Date post: | 04-Jun-2018 |
Category: |
Documents |
Upload: | diegopytboy |
View: | 228 times |
Download: | 0 times |
of 13
8/13/2019 3K3Y Super Slim Install
1/13
3K3y PS3 400x Installation Manual
1. Remove the main PCB from your PS3 Superslim. Locate the four SATA bus capacitors
The SATA Bus Capacitors are circled in red
Illustration 1: Locate The Four SATA Bus Capacitors
8/13/2019 3K3Y Super Slim Install
2/13
. Remove the SATA bus capacitors
Illustration 2: Close Up Of The Four SATA Bus Capacitors
Illustration 3: Remoe The Four SATA Bus Capacitors
8/13/2019 3K3Y Super Slim Install
3/13
3. !it the 3"3# Super Slim adapter to the PS3 PCB
Center the cut out in the 3"3# adapter over the pads for the SATA Bus capacitors. Ali$nthe pads %ith the solder points A&'. (hen you are satisfied %ith the ali$nment solder the)*+ pad to the ad,acent capacitors -blac line/
&Solder points A&' to their respective SATA Bus capacitor pads.
&Solder a %ire from the 0 pad to the top of the t%o capacitors -red line/
&Solder the 3"3# main PCB po%er cable to the 0 -red %ire/ and )*+ -blac/ pads
&Solder a %ire from the L2+ point on the adapter to the centre pin of the cover s%itchconnector
Illustration !: Install the 3"3# A$apter
8/13/2019 3K3Y Super Slim Install
4/13
Illustration %: &ire from LI' (oint to Coer S)itch Connector
8/13/2019 3K3Y Super Slim Install
5/13
Illustration *: Sol$erin+ Complete
8/13/2019 3K3Y Super Slim Install
6/13
. 2nstall The !!Cs
&!it the lon$est %ay !!C to the 42! connector labelled 56T&!it the shortest %ay !!C to the 42! connector labelled 3"S
&!it the and 7 %ay !!Cs
Illustration ,: Fit The FFCs
8/13/2019 3K3Y Super Slim Install
7/13
8/13/2019 3K3Y Super Slim Install
8/13
0. Refit The 'S! 8 Top Shieldin$
Route the !!Cs out of the cutouts as sho%n tae care not to pinch the !!Cs.Reconnect the fan po%er cable 8 the R! cables
Refit the bottom shield and retainin$ scre%s
Illustration .: Refit The /SF 0 Top Shiel$in+
8/13/2019 3K3Y Super Slim Install
9/13
9. Route the 6SB !!C 5ut of the PS3:s case
!eed the 6SB !!C out of the case throu$h a ventilation slot.
Illustration 1: Route the USB FFC
8/13/2019 3K3Y Super Slim Install
10/13
7. 2nsulate the PS3 ;etal%or
Cover the metal shield %ith an insulatin$ material.
7A. Testin$
Before fully reassemblin$ your PS3 it is a $ood idea to test your installation. The 3"3y!!Cs are lon$ enou$h to allo% the PS3 to be reassembled %hile still allo%in$ access tothe 3"3y main PCB.
Replace the PS3 PS6< po%er s%itch< cover s%itch and B+ drive mechanics. Tape thecover s%itch in the do%n position< this simulates the cover in the closed position.
Po%er up the PS3 and observe L=+1. See Appendi> A for an e>planation of the dia$nosticcodes.
&2f the 3"3y indicates Passthru mode chec the cover s%itch is taped do%n correctly andrepeat the test.
&2f the 3"3y indicates =mulation mode then the installation has been successful.
Illustration 11: Insulate the (S3 etal)or
8/13/2019 3K3Y Super Slim Install
11/13
?. 2nstall the 3"3# main PCB
Illustration 13: Install The 3"3# (CB
Illustration 12: 3"34 Connectors
8/13/2019 3K3Y Super Slim Install
12/13
@. ;odify the PS6 Plastic
(ith a sharp nife< remove the plastic pe$ circled in red.
Illustration 1!: o$if4 The (SU (lastic
8/13/2019 3K3Y Super Slim Install
13/13
1. Reassemble the PS3
Replace the PS3 PS6< B+ drive sled 8 plastic top cover.
11. !it the 6SB Adapter
2nsert the %ay !!C into the 6SB adapter main$ sure the blue reinforcement plastic isfacin$ to%ards the female end of the adapter. Plu$ the adapter into one of the PS3:s 6SBport
Appendi> A
The 3"3y %ill display dia$nostic information by flashin$ L=+1. After @ seconds the 3"3ydia$nostics %ill be stable and can be interpreted as follo%s
L=+ State ;eanin$ Action
Slo% !lashin$ S+ card incorrectly seated Reseat the S+ Card
!ast !lashin$ +etectin$ PS3 drive controller Chec solder points A&+
Solid (aitin$ for PS3 Chec solder points =&'
1 flash 3"3y is in Passthru mode
flashes Bad !P)A!P)A ersion 6pdate the !P)A
3 flashes Bad B+ Chec solder points A&+
flashes Bad +1 6pdate the 3"ey.cf$ %ith a valid +10 flashes 3"3y is in =mulation mode
Illustration 1%: Fit the USB A$apter