4-17-14 - ESAB · 2019-01-28 · 4-17-14 CERTIFICATE OF CONFORMANCE INDEX ESAB Electrode ESAB Flux...

4-17-14

CERTIFICATE OF CONFORMANCE INDEX

ESAB Electrode

ESAB Flux or Shielding Gas

AWS Classification

AWS Specification

Section Number

Spoolarc 81 OK Flux 231 F7A2-EM12K-H8 A5.17:1997 1 OK Flux 350 F7A2-EM12K-H8 A5.17:1997 2 OK Flux 429 F7A2-EM12K-H8 A5.17:1997 3 OK Flux 10.71 F7A5-EM12K-H8 A5.17:1997 4 OK Flux 10.62 F7A8-EM12K-H8 A5.17:1997 5 OK Flux 10.72 F7A8-EM12K-H8 A5.17:1997 6 Spoolarc 29S OK Flux 350 F7A2-EM13K-H8 A5.17:1997 7 OK Flux 429 F7A2-EM13K-H8 A5.17:1997 8 OK Flux 10.71 F7A4-EM13K-H8 A5.17:1997 9 Spooalrc 53 OK Flux 429 F7A4-EH12K-H8 A5.17:1997 10 OK Flux 10.71 F7A5-EH12K-H8 A5.17:1997 11 OK Flux 10.62 F7A8-EH12K-H8 A5.17:1997 12 Spoolarc 75 OK Flux 429 F8A4-ENi1K-Ni1-

H8 A5.23::2011 13

OK Flux 10.71 F8A4-ENi1K-Ni1-H8

A5.23::2011 14

OK Flux 10.72 F8A4-ENi1K-Ni1-H8

A5.23::2011 15

Spoolarc ENi4 OK Flux 429 F9A4-ENi4-Ni4-

H8 A5.23::2011 16

OK Flux 10.62 F8A8-ENi4-Ni4-H8 & F9A8-ENi4-Ni4-H8

A5.23: 2011 17

Spoolarc 95 OK Flux 10.62 F10A6-EM2-M2-

H8 A5.23::2011 18

Spoolarc 29S 100% CO2 ER70S-3-H4 A5.18:2005 19 Spoolarc 65 100% CO2 ER70S-2-H4 A5.18:2005 20 Spoolarc 82 100% CO2 ER70S-3 H4 A5.18:2005 21 Spoolarc 86 100% CO2 ER70S-6-H4 A5.18:2005 22 Spoolarc 87HP

100% CO2 ER70S-7 H4 A5.18:2005 23

Spoolarc 83 100% CO2 ER80S-D2 H4 A5.28:2005 24 Spoolarc 83 95Ar/5O2 ER90S-D2 H4 A5.28:2005 25 Spoolarc 95 98Ar/2O2 ER100S-1 H4 A5.28:2005 26

Section 1

ESAB Welding and Cutting Products

256 Midway Drive. Union, South Carolina 29379

Certificate of Conformance To: Specification Requirements For: Welding Electrodes and Fluxes.

This is to certify that this weldng electrode and the flux material are of the same classification as listed below and were tested on the test date shown. The electrode was manufactured and supplied according to Quality System Program of ESAB Welding and Cutting Products, Union, South Carolina All tests required by the AWS Specification were performed, and met all the requirements for the AWS classification listed. The chemical compostion of the electrode and mechanical properties of the deposited weld metal were as follows:

Product: Spoolarc 81 AWS Specification: AWS A5.17 Diameter: 5/32 AWS Classification : F7A2-EM12K-H8 Heat: 0818305 Test Date : 3/1/2013 Flux Material : OK 231 Flux Lot: ME 302051

Chemistry (wt%)C Mn Si P S Cr Ni Mo Cu

AWS Requirements 0.05-0.15 0.80-1.25 0.10-0.35 0.030 0.030 N/R N/R N/R 0.35 Chemical Composition of Electrode 0.10 1.00 0.22 0.009 0.008 0.13 AWS Requirements N/R Chemical Composition of Weld Metal Deposit

Radiography Test: Weld Metal Diffusible Hydrogen:Satisfactory #1 #2 #3 #4 Avg Req'ts

Weld Test Number : (ml/100g) 3.5 3.9 3.7 3.6 3.7 8 max.B1-9192-13-10500 Test: B1-9192-13-10500 Habs = 20.8 70°F; 20%RH

As Welded Mechanical Results: Welding Parameters:AWS Req'ts Results AWS Req'ts Actual

Ultimate Tensile Strength: ksi (MPa) 70-95(483-656) 81.4(561) Current: (Amps) 475-575 550 Yield Strength (0.2% Offset): ksi (MPa) 58 (400) min. 69.6(480) Voltage: (Volts) 27-30 29 Elongation: (%) 22 min. 29 Travel Speed: (in/min) 15-17 16 Reduction in Area: (%) N/R 73 Diameter: in (mm) 5/32 (4.0) 5/32 (4.0)

As Welded Charpy V-Notch Impact Results Plate & Joint Temperature Results Req'ts AWS Req'ts Results

°F (°C) ft-lbs Joules Avg.* ft-lbs Joules ft-lbs (J) Base Plate : A36 A36-20(-29) 46 62 27 37 20 (27) Set-up: 30° 1/2" RO 30° 1/2" RO

24 33 Pass/Layer: 7S/1T40 54 Preheat /Interpass: (°F)/(°F) 60 / 300±25 70/30018 2416 22

* Discard High and Low Value and Avg. Remaining Values Signature: Roger A. Bushey Compliance Manager

Section 2



Certificate of Conformance

To: Specification Requirements

For: Welding Electrodes and Fluxes.


Product: Spoolarc 81 AWS Specification: AWS A5.17 Diameter: 5/32 AWS Classification : F7A2-EM12K-H8 Heat: 08122418 Test Date : 1/31/2014 Flux Material : OK 350 Flux Lot: ME 330061

Chemistry (wt%)

C Mn Si P S Cr Ni Mo Cu

AWS Requirements 0.05-0.15 0.80-1.25 0.10-0.35 0.030 0.030 N/R N/R N/R 0.35 Chemical Composition of Electrode 0.10 1.05 0.21 0.008 0.012 0.03 0.04 0.005 0.09 AWS Requirements N/R Chem. Composition of Weld Metal Dep.

Radiography Test: Weld Metal Diffusible Hydrogen:

Satisfactory #1 #2 #3 #4 Avg Req'ts


As Welded Mechanical Results: Welding Parameters:

AWS Req'ts Results AWS Req'ts Actual

Ultimate Tensile Strength: ksi (MPa) 70-95(483-656) 87.3(603) Current: (Amps) 475-575 550 Yield Strength (0.2% Offset): ksi (MPa) 58 (400) min. 71.3(492) Voltage: (Volts) 27-30 29 Elongation: (%) 22 min. 26 Travel Speed: (in/min) 15-17 15.8 Reduction in Area: (%) N/R 58.6 Diameter: in (mm) 5/32 (4.0) 5/32 (4.0)

As Welded Charpy V-Notch Impact Results Plate & Joint

Temperature Results Req'ts AWS Req'ts Results

°F (°C) ft-lbs Joules Avg.* ft-lbs Joules ft-lbs (J) Base Plate : A515 Gr 70 A515 Gr 70-20(-29) 39 53 37 50 20 (27) Set-up: 30° 1/2" RO 30° 1/2" RO

41 56 Pass/Layer: 8S/1Q38 52 Preheat /Interpass: (°F)/(°F) 60 / 300±25 70/30035 4734 46

* Discard High and Low Value and Avg. Remaining Values Signature:

Roger A. Bushey Compliance Manager

Section 3







Product: Spoolarc 81 AWS Specification: AWS A5.17 Diameter: 5/32 AWS Classification : F7A2-EM12K-H8 Heat: 08122418 Test Date : 2/24/2014 Flux Material : OK Flux 429 Flux Lot: ME 344042

Chemistry (wt%)


AWS Requirements 0.05-0.15 0.80-1.25 0.10-0.35 0.030 0.030 N/R N/R N/R 0.35 Chemical Composition of Electrode 0.10 1.05 0.21 0.008 0.012 0.03 0.04 0.005 0.09 AWS Requirements N/R Chem. Composition of Weld Metal Dep. 0.062 1.36 0.43 0.019 0.013 0.05 0.05 0.02 0.15



Weld Test Number : (ml/100g) 4.3 4.2 4.3 4.3 4.3 8 max.B1-10003-14-10500 Test: B1-10003-14-10500 Habs = 12 70°F; 11%RH



Ultimate Tensile Strength: ksi (MPa) 70-95(483-656) 80.4(555) Current: (Amps) 475-575 550 Yield Strength (0.2% Offset): ksi (MPa) 58 (400) min. 65.6(453) Voltage: (Volts) 27-30 29 Elongation: (%) 22 min. 30 Travel Speed: (in/min) 15-17 16 Reduction in Area: (%) N/R 70.8 Diameter: in (mm) 5/32 (4.0) 5/32 (4.0)







Section 4






This is to certify that this weldng electrode and the flux material are of the same classification as listed below and were tested on the test date shown. The electrode was manufactured and supplied according to Quality System Program of ESAB Welding and Cutting Products, Union, South Carolina. All tests required by the AWS Specification were performed, and met all the requirements listed for the AWS classification. The chemical compostion of the electrode and mechanical properties of the deposited weld metal were as follows:

Product: Spoolarc 81 AWS Specification: AWS A5.17 Diameter: 5/32 AWS Classification : F7A5-EM12K-H8 Heat: 08122418 Test Date : 2/6/2014 Flux Material : OK 10.71 Flux Lot: ME 317022

Chemistry (wt%)


AWS Requirements 0.05-0.15 0.80-1.25 0.10-0.35 0.030 0.030 N/R N/R N/R 0.35 Chemical Composition of Electrode 0.10 1.05 0.21 0.008 0.012 0.03 0.04 0.005 0.09 AWS Requirements N/R Chemical Com. of Weld Metal Deposit 0.076 1.43 0.5 0.018 0.012 0.05 0.05 0.017 0.15






Ultimate Tensile Strength: ksi (MPa) 70-95(483-656) 85.2(588)_ Current: (Amps) 475-575 550 Yield Strength (0.2% Offset): ksi (MPa) 58 (400) min. 71.1(490) Voltage: (Volts) 27-30 29 Elongation: (%) 22 min. 31 Travel Speed: (in/min) 15-17 16 Reduction in Area: (%) N/R 67.2 Diameter: in (mm) 5/32 (4.0) 5/32 (4.0)



°F (°C) ft-lbs Joules Avg.* ft-lbs Joules ft-lbs (J) Base Plate : A36 A36-50 (-46) 33 45 48 65 20 (27) Set-up: 30° 1/2" RO 30° 1/2" RO




Section 5








Chemistry (wt%)





Weld Test Number : (ml/100g) 6.2 6.1 6.5 6.4 6.3 8 max.

2-55025-00-0-A Test: 2-55025-00-0-A Habs = 11.7 69°F; 11%RH



Ultimate Tensile Strength: ksi (MPa) 70-95(483-656) 82(566) Current: (Amps) 475-575 550 Yield Strength (0.2% Offset): ksi (MPa) 58 (400) min. 69.2(478) Voltage: (Volts) 27-30 29 Elongation: (%) 22 min. 30 Travel Speed: (in/min) 15-17 16.1 Reduction in Area: (%) N/R 72.2 Diameter: in (mm) 5/32 (4.0) 5/32 (4.0)







Section 6








Chemistry (wt%)





Weld Test Number : (ml/100g) 6.3 6.5 6.5 6.4 6.4 8 max.2-55026-00-0-A Test: 2-55026-00-0-A Habs = 13.2 72°F; 20%RH



Ultimate Tensile Strength: ksi (MPa) 70-95(483-656) 86.3(596) Current: (Amps) 475-575 525 Yield Strength (0.2% Offset): ksi (MPa) 58 (400) min. 74(511) Voltage: (Volts) 27-30 28 Elongation: (%) 22 min. 29 Travel Speed: (in/min) 15-17 15.9 Reduction in Area: (%) N/R 71.1 Diameter: in (mm) 5/32 (4.0) 5/32 (4.0)







Section 8







Product: Spoolarc 29S AWS Specification: AWS A5.17 Diameter: 5/32 AWS Classification : F7A2-EM13K-H8 Heat: 082T123133 Test Date : 2/27/2014 Flux Material : OK Flux 429 Flux Lot: ME 344042

Chemistry (wt%)


AWS Requirements 0.06-0.16 0.90-1.40 0.35-0.75 0.030 0.030 N/R N/R N/R 0.35 Chemical Composition of Electrode 0.09 1.23 0.56 0.016 0.006 0.04 0.04 0.009 0.08 AWS Requirements N/R Chem. Composition of Weld Metal Dep. 0.059 1.63 0.66 0.025 0.009 0.05 0.05 0.01 0.19



Weld Test Number : (ml/100g) 4.5 4 4.6 4.1 4.3 8 max.B1-10004-14-10500 Test: B1-10004-14-10500 Habs = 11 70°F; 10%RH



Ultimate Tensile Strength: ksi (MPa) 70-95(483-656) 87.1(601) Current: (Amps) 475-575 550 Yield Strength (0.2% Offset): ksi (MPa) 58 (400) min. 71.0(490) Voltage: (Volts) 27-30 29 Elongation: (%) 22 min. 29 Travel Speed: (in/min) 15-17 16 Reduction in Area: (%) N/R 71 Diameter: in (mm) 5/32 (4.0) 5/32 (4.0)







Section 9




To Specification Requirements

For Welding Electrodes and Fluxes.

This is to certify that this weldng electrode and the flux material are of the same classification as listed below and were tested on the test date shown.

The electrode was manufactured and supplied according to Quality System Program of ESAB Welding and Cutting Products, Union, South Carolina.

All tests required by the AWS Specification were performed, and met all the requirements for the AWS classification listed.

The chemical compostion of the electrode and mechanical properties of the deposited weld metal were as follows:

Product: Spoolarc 29S AWS Specification: AWS A5.17Diameter: 5/32 AWS Classification : F7A4-EM13K-H8Heat: 082T123133 Test Date : 2/12/2014Flux Material : OK 10.71Flux Lot: ME 317022

Chemistry (wt%)


AWS Requirements 0.06-0.15 0.90-1.40 0.35-0.75 0.030 0.030 0.35Chemical Composition of Electrode 0.09 1.23 0.56 0.016 0.006 0.04 0.04 0.009 0.08AWS Requirements

Chemical Composition of Weld Metal Deposit 0.071 1.65 0.75 0.023 0.008 0.06 0.05 0.02 0.2

Radiography Test: Satisfactory Weld Metal Diffusible Hydrogen

#1 #2 #3 #4 Avg Req'ts

Weld Test Number : B1-9989-14-10500 (ml/100g) 6.5 6.2 6.4 5.6 6.2 8 Test Number : B1-9989-14-10500 Habs=11.8

As Welded Mechanical Results Welding Parameters


Ultimate Tensile Strength ; ksi (MPa) 70-95(483-656) 91(628) Current: (Amps) 475-575 550

Yield Strength (0.2% Offset); ksi (MPa) 58 (400) 75.7(523) Voltage: (Volts) 27-30 29

Elongation (%) 22 29 Travel Speed: (in/min) 15-17 16.1

Reduction in Area (%) N/R 70.5 Diameter; in (mm) 5/32(4.0) 5/32 (4.0)

As Welded Charpy V-Notch Impact Results Plate

Temperature Results AWS Req'ts AWS Req'ts Results

°F (°C) ft-lbs Joules Avg.* ft-lbs Joules ft-lbs (J) Base Plate : A36 A36-40(-40) 33 45 41 56 20 (27) Set-up 30° 1/2" RO 30° 1/2" RO

51 69 Pass/Layer: 7S/1T35 47 Preheat (°F) /Interpass (°F) : RT / 300±25 70/30046 6243 58

* Discard High and Low Value and Avg. Remaining Values Signature

Section 13






This is to certify that this weldng electrode and the flux material are of the same classification as listed below and

were tested on the test date shown. The electrode was manufactured and supplied according to Quality System Program of

ESAB Welding and Cutting Products, Union, South Carolina. All tests required by the AWS Specification were performed,

and met all the requirements for the AWS classification listed. The chemical compostion of the electrode and mechanical

properties of the deposited weld metal were as follows:

Product: Spoolarc 75 AWS Specification: AWS A5.23Diameter: 5/32 AWS Classification : F8A4-ENi1K-Ni1-H8Heat: 7.51E+09 Test Date : 2/20/2014Flux Material : OK 429Flux Lot: ME 344042

Chemistry (wt%)


AWS Requirements 0.12 0.8-1.40 0.40-0.80 0.020 0.020 0.15 0.75-1.25 0.3 0.35Chemical Composition of Electrode 0.08 0.97 0.56 0.011 0.005 0.03 0.97 0 0.05AWS Requirements 0.10* 1.8* 0.8 0.025 0.03 0.15 0.75-1.10 0.35 0.35Chemical Composition of Weld Metal Deposit 0.05 1.5 0.66 0.021 0.008 0.04 0.85 0.018 0.08

* 1.80 max with carbon restricted to 0.10 max


Coupon #1 #2 #3 #4 Avg Req'ts

Weld Test Number : B1-10005-14-10500 (ml/100g) Results 4 3.9 4.3 4.3 4.7 8Baked flux at 600F/2hrs Test Number : B1-10005-14-10500 Habs= 13.2



Ultimate Tensile Strength ; ksi (MPa) 80-100 (552-690) 88.3(609) Current: (Amps) 475-575 550

Yield Strength (0.2% Offset); ksi (MPa) 68(469) min. 75.6(522) Voltage: (Volts) 27-30 29

Elongation (%) 22 min. 27 Travel Speed: (in/min) 15-17 16

Reduction in Area (%) N/R 65.6 Diameter; in (mm) 5/32 (4.0) 5/32 (4.0)




47 64 Pass/Layer: 7S/1T54 73 Preheat (°F) /Interpass (°F) : 300±25 275/30049 6648 65 Signature

* Discard High and Low Value and Avg. Remaining Values


Section 14










Product: Spoolarc 75 AWS Specification: AWS A5.23Diameter: 5/32 AWS Classification : F8A4-ENi1K-Ni1-H8Heat: 0751150531 Test Date : 2/17/2014Flux Material : OK 10.71Flux Lot: ME 317022

Chemistry (wt%)


AWS Requirements 0.12 0.8-1.40 0.40-0.80 0.020 0.020 0.15 0.75-1.25 0.3 0.35Chemical Composition of Electrode 0.08 0.97 0.55 0.011 0.005 0.03 0.97 0 0.05AWS Requirements 0.12 1.6 0.8 0.025 0.03 0.15 0.75-1.10 0.35 0.35Chemical Composition of Weld Metal Deposit 0.06 1.4 0.71 0.02 0.007 0.05 0.89 0.016 0.11


#1 #2 #3 #4 Avg Req'ts

Weld Test Number : B1-9988-14-10500 (ml/100g) 6.8 6.5 6.8 6.5 6.6 8Baked flux at 600F/2hrs Test Number : B1-9988-14-10500 Habs= 11.7



Ultimate Tensile Strength ; ksi (MPa) 80-100 (552-690) 89.7(619) Current: (Amps) 475-575 550

Yield Strength (0.2% Offset); ksi (MPa) 68(469) 75.1(518) Voltage: (Volts) 27-30 29

Elongation (%) 22 30 Travel Speed: (in/min) 15-17 16




°F (°C) ft-lbs Joules Avg.* ft-lbs Joules ft-lbs (J) Base Plate : A515 Gr 70 A515 Gr 70-40(-40) 39 53 47 64 20 (27) Set-up 30° 1/2" RO 30° 1/2" RO

48 65 Pass/Layer: 7S/1T43 58 Preheat (°F) /Interpass (°F) : 300±25 275/30050 6849 66


Section 15










Product: Spoolarc 75 AWS Specification: AWS A5.23Diameter: 5/32 AWS Classification : F8A4-ENi1K-Ni1-H8Heat: 0751115052 Test Date : 2-19-2014Flux Material : OK 10.72Flux Lot: ME 401012

Chemistry (wt%)


AWS Requirements 0.12 0.8-1.40 0.40-0.80 0.020 0.020 0.15 0.75-1.25 0.3 0.35Chemical Composition of Electrode 0.08 0.97 0.55 0.011 0.005 0.03 0.97 0 0.05AWS Requirements 0.12 1.6 0.8 0.025 0.03 0.15 0.75-1.10 0.35 0.35Chemical Composition of Weld Metal Deposit 0.062 1.70 0.57 0.02 0.007 0.05 0.86 0.01 0.11


#1 #2 #3 #4 Avg Req'ts

Weld Test Number : 2-55027-00-0-A (ml/100g) 6 5.8 5.7 6.3 5.9 8Baked flux at 600F/2hrs Test Number : 2-55027-00-0-A Habs=13.2



Ultimate Tensile Strength ; ksi (MPa) 80-100 (552-690) 92(635) Current: (Amps) 475-575 550

Yield Strength (0.2% Offset); ksi (MPa) 68(469) 78(538) Voltage: (Volts) 27-30 29

Elongation (%) 22 29 Travel Speed: (in/min) 15-17 16




°F (°C) ft-lbs Joules Avg.* ft-lbs Joules ft-lbs (J) Base Plate : A36 Clad A36 Clad-40(-40) 67 91 79 107 20 (27) Set-up 30° 1/2" RO 30° 1/2" RO

84 114 Pass/Layer: 7S/1T86 117 Preheat (°F) /Interpass (°F) : 300±25 275/30080 10879 107


Section 17










Product: Spoolarc ENi4 AWS Specification: AWS A5.23Diameter: 5/32 AWS Classification : F8A8-ENi4-Ni4-H8Heat: 093161846 AWS Classification : F9A8-ENi4-Ni4-H8Flux Material : OK 10.62 Test Date : 7/26/2013Flux Lot: ME 311032

Chemistry (wt%)


AWS Requirements 0.12-0.19 0.60-1.00 0.10-0.30 0.015 0.020 1.60-2.10 0.10-0.30 0.35Chemical Composition of Electrode 0.159 0.74 0.18 0.002 0.002 0.03 1.8 0.15 0.06AWS Requirements 0.14 1.6 0.8 0.03 0.025 1.40-2.10 0.10-0.35 0.35Chemical Composition of Weld Metal Deposit 0.089 0.87 0.38 0.01 0.003 0.04 1.67 0.15 0.05


#1 #2 #3 #4 Avg Req'ts

Weld Test Number : B1-9610-13-10500 (ml/100g) 6.2 6.1 6.1 6.5 6.2 <8

Habs = 63



Ultimate Tensile Strength ; ksi (MPa) 80-100(552-690) 93.4(644)

Ultimate Tensile Strength ; ksi (MPa) 90-110(621-690) 93.4(644) Current: (Amps) 475-575 550

Yield Strength (0.2% Offset); ksi (MPa) 68(469) 80.7 (557) Voltage: (Volts) 27-30 29

Yield Strength (0.2% Offset); ksi (MPa) 78(538) 80.7 (557) Travel Speed: (in/min) 15-17 15

Elongation (%) 20 28 Diameter; in (mm) 5/32 5/32

Elongation (%) 17 28

Reduction in Area (%) N/R 72.5




67 91 Pass/Layer: 7S,1T81 110 Preheat (°F) /Interpass (°F) : 300±25 275/30071 9615 20


Section 20



Certificate of Conformance To Specification Requirements For Welding Electrodes

This is to certify that this weldng electrode is of the same classification as listed below and was tested on the test date shown. The electrode was manufactured and supplied according to Quality System Program of ESAB Welding and Cutting Products, Union, South Carolina. All tests required by the AWS Specification were performed, and met all the requirements for the AWS classification listed. The chemical compostion of the electrode and mechanical properties of the deposited weld metal were as follows:

Product: Spoolarc 65 AWS Specification: AWS A5.18Diameter: 1/16 AWS Classification : ER70S-2 H4Heat: 065253896 Test Date : 6/26/2013

Chemistry (wt%)

C Mn Si P S Cr Ni Mo Cu Ti/Zr/AlAWS Requirements 0.07 0.90-1.40 0.40-0.70 0.025 0.035 0.15 0.15 0.15 0.5 0.05-0.15 / 0.02-0.12 / 0.05-0.15

Chemical Composition of Electrode 0.05 1.13 0.53 0.007 0.01 0.04 0.03 0.01 0.12 0.09 / 0.04 / 0.08

AWS Requirements

Chemical Composition of Weld Metal Deposit: N/R

Radiography Test: Satisfactory Weld Metal Diffusible Hydrogen (ml/100g)

#1 #2 #3 #4 Avg Req'ts

Weld Test Number : 2-54282-00-0-A (Chem) & F2-9548-13-10500 1.4 1.3 1.5 1.2 1.3 4.0 max

2-54274-00-0-A (H2) Test Number 2-54274-00-0-A Habs= 20.9



Ultimate Tensile Strength ; ksi (MPa) 70(483) 79.8(550) Current: (Amps) 330.-360 325


Elongation (%) 22 24 Travel Speed: (in/min) 13±1 12.5

Reduction in Area (%) N/R 60 Diameter; in (mm) 1/16 1/16

As Welded Charpy V-Notch Impact Results Shielding Gas 100% CO2 100% CO2

Temperature Results AWS Req'ts

°F (°C) ft-lbs Joules Avg.* ft-lbs Joules ft-lbs (J) Plate AWS Req'ts Results -20(-29) 61 83 43 58 20 (27) Base Plate : A515 Gr 70 A285 Gr C

36 49 Set-up 45° 1/2" RO 45° 1/2" RO71 96 Pass/Layer: 4S / 2T

28 38 Preheat (°F) /Interpass (°F) : RT/300±25 200 / 325

32 43


Section 22

ESAB Welding and Cutting Products256 Midway Drive. Union, South Carolina 29379

Certificate of Conformance To Specification Requirements For Welding Electrodes

This is to certify that this weldng electrode is of the same classification as listed below and was tested on the test date shown. The electrode was manufactured and supplied according to Quality System Program of ESAB Welding and Cutting Products, Union, South Carolina. All tests required by the AWS Specification were performed, and met all the requirements for the AWS classification listed. The chemical compostion of the electrode and mechanical properties of the deposited weld metal were as follows:

Product: Spoolarc 86 AWS Specification: AWS A5.18Diameter: 1/16 AWS Classification : ER70S-6 H4Heat: 100000542 Test Date : 6/20/2013

Chemistry (wt%)

C Mn Si P S Cr Ni Mo CuAWS Requirements 0.06-0.15 1.40-1.85 0.80-1.15 0.025 0.035 0.15 0.015 0.15 0.5Chemical Composition of Electrode 0.072 1.43 0.86 0.008 0.0062 0.02 0.009 0.009 0.1AWS Requirements N/A N/A N/A N/A N/A N/A N/A N/A N/AChem. Composition of Weld Metal Deposit N/A N/A N/A N/A N/A N/A N/A N/A N/A

Radiography Test: Satisfactory Weld Metal Diffusible Hydrogen (Typcial)#1 #2 #3 #4 Avg Req'ts

Weld Test Number : 2-54082-00-0-A (ml/100g) 1.3 1.3 1.2 1 1.2 4.0 max2-54082-00-0-A Habs = 15.5



Ultimate Tensile Strength ; ksi (MPa) 70(483) 76.7(529) Current: (Amps) 330-360 346



Reduction in Area (%) N/R 67.5 Diameter; in (mm) 1/16 1/16

As Welded Charpy V-Notch Impact Results Shielding Gas 100% CO2 100% CO2Temperature Results AWS Req'ts Plate °F (°C) ft-lbs Joules Avg.* ft-lbs Joules ft-lbs (J) AWS Req'ts Results -20(-29) 88 119 78 106 20 (27) Base Plate : A515 Gr 70 A515 Gr70

80 108 Set-up 45° 1/2" RO 45° 1/2" RO76 103 Pass/Layer: 5S,1T74 100 Preheat (°F) /Interpass (°F) : RT/300±25 70/30078 106


Section 23

ESAB Welding and Cutting Products256 Midway Drive. Union, South Carolina 29379



For Welding Electrodes

This is to certify that this weldng electrode is of the same classification as listed below and was tested on the test date shown.




Product: Spoolarc 87HP AWS Specification: AWS A5.18

Diameter: 0.045 AWS Classification : ER70S-7 H4

Heat: 8510209474 Test Date : 7/31/2013

Chemistry (wt%)


AWS Requirements 0.07-0.15 1.50-2.00 0.50-0.80 0.025 0.035 0.15 0.15 0.15 0.5

Chemical Composition of Electrode 0.087 1.54 0.55 0.006 0.0067 0.02 0.01 0.01 10

AWS Requirements N/A N/A N/A N/A N/A N/A N/A N/A N/A

Chemical Composition of Weld Metal Deposit N/A N/A N/A N/A N/A N/A N/A N/A N/A


#1 #2 #3 #4 Avg Req'ts

Weld Test Number : 2-54292-00-0-A (ml/100g) 1.7 1.5 1.6 1.4 1.5 4

Habs = 19.57 2-54292-00-0-A




Yield Strength (0.2% Offset); ksi (MPa) 58(400) 63.6 (439) Voltage: (Volts) 27-31 28

Elongation (%) 22 29 Travel Speed: (in/min) 13±1 12

Reduction in Area (%) N/R 71 Diameter; in (mm) 0.045 0.045

As Welded Charpy V-Notch Impact Results Shielding Gas 100% CO2 100% CO2

Temperature Results AWS Req'ts Plate

°F (°C) ft-lbs Joules Avg.* ft-lbs Joules ft-lbs (J) AWS Req'ts Results

-20(-29) 112 152 105 142 20 (27) Base Plate : A285 Gr C A515 Gr70

102 138 Set-up 45° 1/2" RO 45° 1/2" RO

104 141 Pass/Layer: 3S,3T

104 141 Preheat (°F) /Interpass (°F) : RT/300±25 70/325

106 144


Section 24










Product: Spoolarc 83 AWS Specification: AWS A5.28Diameter: 1/16 AWS Classification : ER80S-D2Heat: 832240927 Test Date : 2/17/2014

Chemistry (wt%)


AWS Requirements 0.07-0.12 1.60-2.10 0.50-0.80 0.025 0.025 0.15 0.40-0.60 0.5Chemical Composition of Electrode 0.08 1.77 0.64 0.009 0.003 0.06 0.06 0.5 0.05AWS Requirements N/A N/A N/A N/A N/A N/A N/A N/A N/AChemical Composition of Weld Metal Deposit 0.74 1.2 0.35 0.01 0.007 0.06 0.06 0.49 0.09


#1 #2 #3 #4 Avg Req'ts

Weld Test Number : B1-9975-14-10500 (ml/100g) 1.2 1.1 1.1 1.2 1.1 4.0 max.Test Number B1-9975-14-10500 Habs=10.7



Ultimate Tensile Strength ; ksi (MPa) 80(550) min. 98.0(676) Current: (Amps) 300-360 348

Yield Strength (0.2% Offset); ksi (MPa) 68(470) min. 85.3(588) Voltage: (Volts) 27-32 28

Elongation (%) 17 min. 26 Travel Speed: (in/min) 13±2 14.3


As Welded Charpy V-Notch Impact Results Shielding Gas 100% CO2 100% CO2Temperature Results AWS Req'ts Plate


-20(-29) 60 81 56 76 20 (27) Base Plate : A515 Gr 70 A515 Gr7044 60 Set-up 45° 1/2" RO 45° 1/2" RO55 75 Pass/Layer: 4S, 2T, 62 84 Preheat (°F) /Interpass (°F) : 300±25 325/32554 73


Section 25










Product: Spoolarc 83 AWS Specification: AWS A5.28Diameter: 1/16 AWS Classification : ER90S-D2Heat: 083W36146 Test Date : 4/17/2014

Chemistry (wt%)


AWS Requirements 0.07-0.12 1.60-2.10 0.50-0.80 0.025 0.025 N/R 0.15 0.40-0.60 0.5Chemical Composition of Electrode 0.1 1.7 0.69 0.013 0.014 0 0.06 0.46 0.1AWS Requirements N/R N/R N/R N/R N/R N/R N/R N/R N/RChemical Composition of Weld Metal Deposit 0.085 1.62 0.64 0.011 0.016 0.05 0.07 0.49 0.07


#1 #2 #3 #4 Avg Req'ts

Weld Test Number : B1-10091-14-10500 (ml/100g) 2.5 2.4 2.4 2.3 2.4 4.0 max.Test Number B1-9974-14-10500 (98Ar / 2O2) Habs=10.7



Ultimate Tensile Strength ; ksi (MPa) 90(620) min. 99.1(684) Current: (Amps) 340-420 369

Yield Strength (0.2% Offset); ksi (MPa) 78(540) min. 87.1(601) Voltage: (Volts) 25-30 27.8

Elongation (%) 17 min. 24 Travel Speed: (in/min) 13±2 12.9


As Welded Charpy V-Notch Impact Results Shielding Gas Ar /1-5% O2 95Ar / 5O2Temperature Results AWS Req'ts Plate


-20(-29) 105 142 115 156 20 (27) Base Plate : A285 A285 Butt114 155 Set-up 45° 1/2" RO 45° 1/2" RO127 172 Pass/Layer: 2S, 3T121 164 Preheat (°F) /Interpass (°F) : 300±25 325/325111 150


N/R = Not Required N/A = Not Applicable

Section 26






This is to certify that the welding electrode tested met all the requirements for AWS classification listed and was tested

on the test date shown.

The electrode was manufactured and supplied according to Quality System Program of ESAB Welding and Cutting Products,

Union, South Carolina. All tests required by the AWS Specification were performed, and met all the requirements for the

AWS classification listed. The chemical compostion of the electrode and mechanical properties of the deposited weld

metal were as follows:

Product: Spoolarc 95 AWS Specification: AWS A5.28Diameter: 0.045 AWS Classification : ER100S-1 Heat: 095824350 Test Date : 1/31/2014

Chemistry (wt%)

C Mn Si P S Cr Ni Mo V

AWS Requirements 0.08 1.25-1.80 0.20-0.55 0.010 0.010 0.3 1.40-2.10 0.25-0.55 0.05Chemical Composition of Electrode 0.054 1.51 0.33 0.008 0.007 0.11 1.85 0.35 0.005

Ti Zr Al Cu TOE N

AWS Requirements 0.1 0.1 0.1 0.25 >0.5 N/AChemical Composition of Electrode 0.018 <0.001 0.0008 0.11 0.025 0.0017

AWS Requirements N/A N/A N/A N/A N/A N/A N/A N/A N/AChemical Composition of Weld Metal Deposit 0.05 1.43 0.29 0.008 0.009 0.14 1.96 0.41 0.13


#1 #2 #3 #4 Avg Req'ts

Weld Test Number : B1-10012-14-10500 (ml/100g) 3.6 3.6 3.6 3.6 3.6 4.0 max.Test Number B1-10015-14-10500 Habs=10.0




Yield Strength (0.2% Offset); ksi (MPa) 88(607) 95.9(661) Voltage: (Volts) 27-32 27.6


Reduction in Area (%) N/R 69.9 Diameter; in (mm) 0.045 0.045

As Welded Charpy V-Notch Impact Results Shielding Gas 98Ar/2O2 98Ar/2O2Temperature Results AWS Req'ts Plate


-60(-51) 126 171 117 159 20 (27) Base Plate : HY-80 HY-80102 138 Set-up 45° 1/2" RO 45° 1/2" RO119 161 Pass/Layer: 3S, 2T113 153 Preheat (°F) /Interpass (°F) : 300±25 275/275119 161


Roger A. Bushey

TOE: Total Other Elements excluding Fe. N/A: Not Applicable

Date post:	20-Jan-2020
Category:	Documents
Upload:	others
View:	33 times
Download:	2 times

4-17-14 - ESAB · 2019-01-28 · 4-17-14 CERTIFICATE OF CONFORMANCE INDEX ESAB Electrode ESAB Flux...

Documents