4-WAY SPLITTER (FOR 6-ROW SRES PLANTERS)
INSTALLATION PROCEDURE
99 M AVE PHONE (515) 382-3506 NEVADA, IA 50201-1549 FAX (515) 382-2973 USA BEEPER (515) 239-0642
www.almaco.com
MOP0201041
SRES 4-way Splitter Kit INSTALLATION PROCEDURE
ALMACO 4-WAY SPLITTER INSTALLATION PROCEDURE
for SRES 6-row planters
INSTALLATION Page 1 of 19
SRES 4-way Splitter Kit INSTALLATION PROCEDURE
Page 2 of 19 INSTALLATION
SRES 4-way Splitter Kit INSTALLATION PROCEDURE
Center seat moved one mount to the right where ladder was mounted.
Rt
Figure 1: New seat and ladder locations (left-rear STEP - 1 Reposition center seat and right side ladder Move center seat one row space to the right and move the right side
as shown in Figure 1.
INSTALLATION
ight side ladder moved o center mount
view)
ladder to the center mount
Page 3 of 19
SRES 4-way Splitter Kit INSTALLATION PROCEDURE
(a)
(b)
(e)
Vertical pipe
Figure 2: Existing gate valve (left view) STEP - 2 Remove existing gate valves
(a) Disconnect pneumatic hoses (DO NOT cut hoses - ALMACO splitters will use the same quick connections).
(b) Disconnect flexible seed drop tubes (DO NOT cut tubes). (c) Dismount head set connectors (d) Dismount or disconnect any other custom components attached to gate valves or in the way
of removing gate valves. (e) Loosen gate valve pipe clamp from vertical pipe then remove gate valve and clamp.
Page 4 of 19 INSTALLATION
SRES 4-way Splitter Kit INSTALLATION PROCEDURE
(b) (a)
Figure 3: New location for Hammerhead mount and Control Box (left end - rear view) STEP - 3 Relocate Main control box and Hammerhead mount
(a) Move Hammerhead mount to right side of left operator’s seat. (b) Move Control box to the right of the Hammerhead mount.
(Use existing pipes and clamps)
INSTALLATION Page 5 of 19
SRES 4-way Splitter Kit INSTALLATION PROCEDURE
ALMACO provided mounting bracket
Figure 4: New Big John control box location (rear view) STEP - 4 Remount Big John control box Remount Big John control box above Main control box with ALMACO provided mounting
bracket. Position control box as desired for left side operator.
Page 6 of 19 INSTALLATION
SRES 4-way Splitter Kit INSTALLATION PROCEDURE
(b)(c)
(a)
STEP
(a
(b
(c
Seed Drop Tube
Figure 5: Location of ALMACO 4-way Splitter on
- 5 Mount ALMACO 4-way Splitter on left side of p) Slide pipe clamp for 4-way Splitter Mount up onto w
planter, and clamp tight to pipe. ) Set pipe clamp as high as possible on vertical pipe
is necessary for good seed flow through the seed d) Center and attach 4-way Splitter mount to pipe clam
INSTALLATION
Seed Drop Tube
left side of planter (front view)
lanter elded pipe, located on the left side of the
that will still allow T-handle to turn. This rop tubes. p.
Page 7 of 19
SRES 4-way Splitter Kit INSTALLATION PROCEDURE
(b)
(c)
(a)
Seed Drop Tubes
Figure 6: Location of ALMACO 4-way Splitter on right side of planter (front view) STEP - 6 Mount right side ALMACO 4-way Splitter
(a) Slide pipe clamp for 4-way Splitter Mount up onto welded pipe, located on the right side of the planter, and clamp tight to pipe.
(b) Set pipe clamp as high as possible on vertical pipe that will still allow T-handle to turn. This is necessary for good seed flow through the seed drop tubes.
(c) Align far right mounting holes of 4-way Splitter Mount and attach to pipe clamp.
Page 8 of 19 INSTALLATION
SRES 4-way Splitter Kit INSTALLATION PROCEDURE
48” (center-to-center of Splitters)
(a) & (d)
Main pipe hanger
(b) - c- mouand ri(a)
Figure 7: Location of ALM STEP - 7 Mount center ALMACO 4-w
(a) Reposition the mounting pipe, hanger. The mounting pipe shthe right-side ALMACO 4-way
(b) Slide pipe clamp for 4-way SplSet pipe clamp as high as possis necessary for good seed flow
(c) Center and attach 4-way Splittmounting pipe will help to keep
(d) Make final adjustments to achiALMACO 4-way Splitters as sh
(c) - cannot see in this view - similar toleft Splitter mount
RA4s
annot see in this view nt clamp similar to left ght Splitter clamps
ACO 4-way Splitter in middle of planter (rear vie
ay Splitter which was used for the center gate valve, on mould be positioned so the center-to-center distaSplitter and the center ALMACO 4-way Splitter itter mount up onto the mounting pipe and clamible on vertical pipe that will still allow T-handle through the seed drop tubes.
er mount to pipe clamp. Centering Splitter mou the pipe from spinning in its hangers. eve the 48” center-to-center distance needed bown in figure 7.
INSTALLATION
ight-side LMACO -way plitter
w)
ain pipe nce between is 48”. p tight to pipe. to turn. This
nt on the
etween
Page 9 of 19
SRES 4-way Splitter Kit INSTALLATION PROCEDURE
ALMACO 4-way Splitter Mount
Vertical mounting pipe for 4-way Splitter
Figure 8a: Safety-Pin location
Drill a 9/32” dia. hole through pipe
Safety-Pin
3/8”
Figure 8b: Safety-Pin location STEP - 8 Install Safety-Pins for ALMACO 4-way Splitters
(a) 3/8” up from the bottom of each pipe that an ALMACO 4-way Splitter is mounted (3-pipes) drill a 9/32” diameter hole through both sides of the pipe as shown above.
(b) Insert ALMACO provided Safety-Pin. (These Safety-Pins will keep the 4-way Splitters from completely falling off the mounting pipes if
a pipe clamp would happen to come loose.) Page 10 of 19 INSTALLATION
SRES 4-way Splitter Kit INSTALLATION PROCEDURE
Red hose
Green hose
Figure 9: Pneumatic hose connections to ALMACO 4-way Splitters STEP - 9 Reconnecting pneumatic hose quick couplers to ALMACO 4-way Splitters
(a) Connect red hose into connector marked “RED”. (b) Connect green hose into connector marked “GREEN”. (c) Route hoses appropriately.
INSTALLATION Page 11 of 19
SRES 4-way Splitter Kit INSTALLATION PROCEDURE
Clear flexible tube connector
Clear flexible tube connector
End of tubes with beveled inside diameter
Figure 10: ALMACO PVC seed drop tubes (rear view) STEP - 10 Attach ALMACO PVC seed drop tubes to ALMACO 4-way Splitters
(a) Cut PVC tubes to desired length (determined by tube location) as shown in figure 10 (planter is in lowered or planting position). DO NOT CUT OFF PVC TUBE END WITH BEVELED INSIDE DIAMETER! Lower end of tube should reach opening in platform.
(b) Connect PVC seed drop tubes to 4-way Splitter drop tubes with clear flexible tube connectors (provided by ALMACO). Make sure the end of the tube with the beveled inside diameter is connected here (or used as the upper end of the tube).
Page 12 of 19 INSTALLATION
SRES 4-way Splitter Kit INSTALLATION PROCEDURE
Figure 11a: Flexible seed drop tubes attached to ALMACO PVC seed drop tubes (left-rear view)
ALMACO PVC seed drop tubes
Slide excess flexible tubing over PVC tubes.
Use ALMACO provided plastic pads between clamp and flexible tubing.
Clamp flexible tubing to lower end of PVC tube.
Flexible tubing should telescope in and out of metering unit funnel.
(a) - minimum of 2-1/2” when planter is in raised position
Figure 11b: ALMACO provided plastic pads for clamping flexible tubing to PVC tube.
STEP - 11 Connect flexible seed drop tubes to ALMACO PVC seed drop tubes
(a) Insert flexible tubing into metering unit funnel. When planter is in raised position and row unit is in its lowest position, metering unit funnel should still overlap flexible tubing by a minimum of 2-1/2”.
(b) Slide excess flexible tubing over PVC tubes and clamp flexible tubing to bottom of PVC tubes. Use two ALMACO provided plastic pads between clamp and flexible tubing. Leave enough flexible tubing below PVC tube to keep it engaged with metering unit funnel when planter is in raised and lowered positions.
NOTE: Too much flexible tubing between PVC tube and metering unit funnel can hinder seed flow or cause seed hang-up.
INSTALLATION Page 13 of 19
SRES 4-way Splitter Kit INSTALLATION PROCEDURE
Left-side 4-way Spliter
Lhc
Figcon
STE
Pag
eft-side eadset onnector
Right-side 4-way Splitter
ure12a: New location of left headset nector (left-rear view)
Figure 12b: New location of right heaconnector (right-rear view)
Center 4-way Spliter
Figure 12c: New location of center headset connector (left-rear view)
P - 12 Remount headset connectors Remount headset connecters so headsets can be connected conveniently and functiproperly. See figures 12a, 12b, and 12c.
e 14 of 19 INSTALLATION
Right-side headset connector
dset
Center headset connector
on
SRES 4-way Splitter Kit INSTALLATION PROCEDURE
Left-side 4-way Splitter
Left-side seed packet holder
ALMACO provided pipe and hangers Main pipe hanger
Figure 13: New left-side seed packet holder location (left-front view) STEP - 13 Move left side seed packet holder Remount the left-side seed packet holder to the left end of the main pipe hanger. Use ALMACO
provided pipe and hangers.
INSTALLATION Page 15 of 19
SRES 4-way Splitter Kit INSTALLATION PROCEDURE
Right-side seed packet holder
Center seed packet holder Right-side
4-way Splitter
Main pipe hangerALMACO provide pipe and hangers
Figure 14: New right-side and center seed packet holder locations (right-front view) STEP - 14 Move right-side and center seed packet holders
(a) Remount the right-side seed packet holder to the right end of the main pipe hanger. Use ALMACO provided pipe and hangers.
(b) Remount the center seed packet holder just to the inside of the right-side seed packet holder. Reposition existing pipes and hangers to locate center seed packet holder
Page 16 of 19 INSTALLATION
SRES 4-way Splitter Kit INSTALLATION PROCEDURE
Main pipe hanger
ALMACO handrails
Attach to bottom side of main pipe hanger
Mounting tubes for ladders
Figure 15: ALMACO handrail locations (left-rear view) STEP - 15 Mount ALMACO supplied handrail Center ALMACO supplied handrails over the mounting tubes for ladders. Attach handrails to the
bottom side of the main pipe hanger with ALMACO supplied hardware as shown above.
INSTALLATION Page 17 of 19
SRES 4-way Splitter Kit INSTALLATION PROCEDURE
Headset junction box
Main pipe hanger
Figure 16: New location of headset junction box (front view) STEP - 16 Relocate headset junctions box If needed, relocate headset junction box on top of main pipe hanger on left side of planter.
Page 18 of 19 INSTALLATION
SRES 4-way Splitter Kit INSTALLATION PROCEDURE
Customized component
Customized components
Customized component
FIGURE 17: Customized components relocated
STEP - 17 Relocate customized components If necessary, you may need to relocate any customized components your planter may have
(components specific to you planter).
INSTALLATION Page 19 of 19
Reposition center seat and right side ladder