beka

series

40

APPLICATIONS• Commercial and housing developments

• Public buildings

KEY ADVANTAGES• Operating temperature (Ta): -20˚C to +35˚C

• Minimum 60 000hrs useful lifetime (L70)

• Effective high-power LED, 4000K(*) at a colour rendering

index >80

• Ingress protection - IP 65

• 3 year warranty*

• High-pressure die-cast aluminium base

• High-impact acrylic diffuser

• Reduced light pollution

CONSTRUCTION DETAILSThe luminaire consists of a high-pressure die-cast aluminium

(EN 1706 AC-44300) base and eyelid trim ring and clear

prismatic or opal high-impact acrylic diffuser. It is designed

to operate LEDs of 1095lm (8W).

SABS MARKSThe luminaire bears the SANS 60598-2-1 safety mark.

INGRESS PROTECTIONIP 65 in compliance with SANS 60598-2-1:

The IP rating is certified by an SABS test report.

BASE• All base castings are manufactured from high-pressure die-

cast aluminium, finished both outside and inside in white

epoxy powder coating for added protection and reflectivity.

• It is simple to install due to four mounting holes provided

outside the lamp compartment through lugs that form part

of the base casting.

• The incorporated reflector is manufactured from 99.98%

super pure deep anodized aluminium for optimal downward

light output.

beka

series 40

• The trim ring casting is mounted onto the base casting by

stainless steel M5 Allen head screws, located outside the

lamp compartment.

• The fixing holes can be supplied with stainless steel helicoil

inserts on request.

DIFFUSER• A clear prismatic or opal non-discolouring high-impact

acrylic injection moulded diffuser is used throughout the

range.

• It offers excellent vandal resistance, is highly translucent

and will not discolour even when subjected to the harshest

UV environments.

• A silicon sponge gasket is fitted into a special groove in the

diffuser to prevent damage to the gasket during installation.

• It fits snugly over a tongue provided on the base casting,

thus achieving the certified ingress protection rating of

IP 65.

TRIM RING• The eyelid trim ring casting is manufactured from high-

pressure die-cast aluminium and is finished in a special

multi-stage epoxy powder surface coating.

ELECTRICAL COMPONENTS• The electronic control gear is mounted directly onto the

base casting.

• It is suitable for operation with the specified rating of the

lamp on a 230V ±10% 50Hz single phase system.

• The luminaire is supplied with a 300mm supply lead.

• All external screws, bolts and metals are stainless steel or

of non-corrosive material.

• Mains connections are by means of a suitable screw

terminal block with a wire clamping contact.

• The power factor is rated at ≥0,9.

Series 42 Black, opaque Series 41 Silver, prismatic Series 41 White, prismatic

(*) Correlated colour temperature (CCT)

*Terms and conditions apply

Front view

195

341

Bottom view

105

48

Side view

LIGHT DISTRIBUTIONS

BEKA Series 40 LED 8W

45˚

60˚

75˚

90˚

30˚15˚ 0˚

0˚/180˚ 90˚/270˚

cd/klm300 200400

150818A -SERIES 40 11W 20 LEDs 700mA / 2 X WU-M-508-840 557995 PCB'Spolar diagram

BEKA (PTY) LTD.P.O. BOX 120, 13 West View Road, Olifantsfontein-1665 South Africa- Tel +27 11 238 0132 - FAX +27 11 238 0186 page 2 / 21

C0 C9030°30°

45°45°

60°60°

75°75°

90°90°

105°105°

200

300

400

500

600

I ( cd/klm )

100

DIMENSIONS IN MM

Four fixing holes to hold the trim ring casting to the base casting by stainless steel M5 Allen head screws, located outside the lamp compartment.

Base casting is manufacturedfrom high-pressure die-cast

aluminium, finished both outside and inside in white

epoxy powder coating for added protection

and reflectivity.

Tongue provided on the base casting fits into

the silicon sponge gasket seated in the diffuser,

thus achieving SABS certified IP 65

protection.Four mounting holes provided outside the lamp compartment ensure the integrity of the certified IP rating. The mounting holes are raised 2mm from the base, preventing rainwater from running over the luminaire surface, and are also offset from the main axis in order to prevent accidental damage to conduits during the installation process.

99.98% super pure deepanodized aluminiumreflector.

The grommet provided in the base casting allows the feeding through of the Teflon® wiring supplied, thus ensuringintegrity of IP 65 rating.

It is designed to operate

LEDs of up to 8W.

Electronic data files can be downloaded from www.beka-schreder.co.za/knowledge-base

ELECTRICAL

Correlated colour temperature Warm white (3000K)

MECHANICAL

Mounting spacer unit

35mm deep surface mount

50mm deep surface mount

50mm deep recessed

Extras Stainless steel helicoil inserts

Colour

White (RAL 9003), Textured finish

Silver (RAL 9023), Textured finish

Other RAL colour, Matt finish

Other RAL colour, Brilliant finish

Other RAL colour, Textured finish

OPTIONS AND ACCESSORIES

ORDERING DATA

Copy

right

© B

EKA

Schr

éder

(Pty

) Ltd

201

7 –

13 W

est V

iew

Roa

d –

PO B

ox 1

20 –

Olif

ants

font

ein

– 16

65 –

Sou

th A

frica

- Th

e in

form

atio

n, d

escr

iptio

ns a

nd il

lust

ratio

ns h

erei

n ar

e of

onl

y an

indi

cativ

e na

ture

. Due

to a

dvan

ced

deve

lopm

ents

, w

e m

ay b

e re

quire

d to

alte

r the

cha

ract

eris

tics

of o

ur p

rodu

cts

with

out n

otic

e. A

s th

ese

may

pre

sent

diff

eren

t cha

ract

eris

tics

acco

rdin

g to

the

requ

irem

ents

of i

ndiv

idua

l cou

ntrie

s, w

e in

vite

you

to c

onsu

lt us

.

DESCRIPTION LINE CURRENT (A) LUMEN (1) MASS (KG)

41 BULKHEAD LED 8W prismatic-clear 0.03 1 095 2.5

42 BULKHEAD LED 8W opaque 0.03 1 095 2.5

EMERGENCY VERSION - 1 HOUR

EM-SERIES 41 8W LED 1hr 0.03 1 095/770 (EM) 2.5

EM-SERIES 42 8W LED 1hr 0.03 1 095/770 (EM) 2.5

EMERGENCY VERSION - 3 HOURS

EM-SERIES 41 8W LED 3hr 0.03 1 095/770 (EM) 2.5

EM-SERIES 42 8W LED 3hr 0.03 1 095/770 (EM) 2.5

Standard colours: Black (RAL 9017), Textured finish Standard CCT: Neutral white (4000K)

(1) The type of LED used is subject to change due to the ongoing rapid progress taking place in LED technology.

Designed and manufactured by BEKA Schréder (Pty) Ltd - South AfricaManufacturers of Luminaires and Glass Fibre Poles

SANS 475SANS 60598

12/19

BEKA Schréder (Pty) Ltd | 13 West View Road | P.O. Box 120 | Olifantsfontein | 1665 | South Africa T: +27 11 238 0000 | F: +27 11 238 0180info@beka-schreder.co.za | www.beka-schreder.co.za