40 Tower Fan
Bef
ore
usin
g yo
ur T
ower
Fan
, ple
ase
read
thi
s m
anua
l.
Important Satety InstructionsOperating InstructionsCleaning and MaintenanceTroubleshootingWarranty Manufacturing InfoWarningContact Us
45-7
889999
TABLE OF CONTENTS
4
When using your this appliance, basic safety precautions should always be followed to reduce the risk of fire, electric shock, and/ or injury to person. Incorrect operation due to ignoring instructions may cause harm or damage.
• Read all instructions before using the appliance.
• This appliance has a polarized plug (one blade is wider than the other). To reduce the risk of electric shock, this plug is intended to fit in a polarized outlet only one way. If the plug does not fit fully in the outlet, reverse the plug. If it still does not fit, contact a qualified electrician. DO NOT attempt to defeat this safety feature.
• WARNING - To reduce the risk of fire or electric shock, DO NOT use this fan with any solid-state speed control device.
• DO NOT leave the fan running unattended.
• Keep electrical appliances out of reach from Children or infirm persons. DO NOT let them use the appliances without supervision.
• If the supply cord is damaged, it must be replaced by manufacturer or its service agent or a similarly qualified person in order to avoid a hazard.
• This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety. Young children should be supervised to ensure that they DO NOT play with the appliance.
• When the fan was assembled, the rotor blade guard shall not be taken off anymore. - Unplug the fan for prior cleaning. - The rotor guard shall not be dissembled if you want to clean the rotor blades. - Wipe the fan enclosure and rotor blade guard with a slightly damp cloth.
• This product employs overload protection (fuse). A blown fuse indicates an overload or short-circuit situation. If the fuse blows, unplug the product from the outlet. Replace the fuse as per the user servicing instructions. Follow product marking for proper fuse rating. If the replacement fuse blows, a short-circuit may be present and the product should be discarded or returned to an authorized service engineer for examination and/or repair.
• a) DO NOT operate fan with a damaged cord or plug. Discard fan or return to an authorized service facility for examination and/or repair.
• b) DO NOT run cord under carpeting. DO NOT cover cord with throw rugs, runners, or similar coverings. DO NOT route cord under furniture or appliances. Arrange cord away from traffic area so that it will not be tripped over.
FOR SAFE OPERATION• Never insert fingers, pencils, or any other
object through the grille when fan is running.
• Disconnect fan when moving from one location to another.
• Make sure the fan is on a stable surface when operating to avoid overturning.
• DO NOT use fan near or under open window. Rain may create electrical hazard.
Important Satety Instructions
The appliance must be placed on a flat firm surface.
SAVE THESE INSTRUCTIONS For Household Use Only
WARNING
5
Control Panel
Display Window
Fan Body
Base
FOR SAFE OPERATIONNote:
Place the Tower Fan on the package foam or other
soft surfaces and invert it to avoid scratch mark
when install the base.1 Take away the two parts of the base from packaging box. Align the centers of the two parts of the base and place them in a crossed form. Rotate one of the two bases to align holes, then match and lock.
2 Remove the four screws from the Fan body. When the base and the Fan body are aligned accurately, fix and tighten the base to the Fan body with the screws.
Operating Instructions
PARTS DESCRIPTION
6
CONTROL PANEL
REMOTECONTROL
• Press buttons on the top of Fan body to set corresponding functions:
• Press “Speed” to adjust the speed from Low, Medium or High.
• Press “Timer” to adjust the time:
- Set timed power off as 1 hour, 2 hours, 4 hours, 8 hours in starting up mode.
- Set starting up as 1 hour, 2 hours, 4 hours, 8 hours in standby mode (power on but not starting up).• Press “MODE” to adjust wind mode (Natural wind, Sleep wind, Oscillating wind).• Press “SWING” to turn on or off the swing of the fan.
Display panel
Time display
Natural wind
Sleep wind
Oscil-lating
Fan speed
8
Low Med Hi
Nat Slp Osc
Operating Instructions
7
Operating Instructions
REMOTE CONTROLLER BUTTONS
Timer key
Swing key
Mode key
Start up/Standby key
“+” key
“-” key
+
-
Point the remote control toward the receptor on Fan body and press the desired button. The remote control will work at distances of up to roughly 16 feet and an angle of 30 degrees left and right of the control panel. The buttons on the control panel such as ON/OFF, SPEED, TIMER, SWING have the same functions as those of the corresponding keys on the Remote Control.
8
Cleaning and Maintenance
Troubleshooting
User Servicing Instructionsa) Grasp plug and remove from the receptacle or other outlet device. Do not unplug by pulling on cord.b) Open fuse cover. Slide open fuse access cover on top of attachment plug towards blades.c) Remove fuse carefully.d) Risk of fire. Replace fuse only with 2.5 Amp, 125 Volt fuse.e) Close fuse cover. Slide closed the fuse access cover on top of attachment plug.
NOTE: 1. When you replace the fuse, please don’t operate suddenly or overexert, or else the product will be damage or cause accident.2. When you feel it hard to be operated, please make sure you have got the right way.
Cleaning1. Be sure to unplug from the electrical supply source before cleaning.2. Plastic parts should be cleaned with mild soap and a damp cloth or sponge. Thoroughly remove soap film with clean water.3. Be sure not to make water or other liquid enter the inside of Fan body.
PROBLEMS SOLUTIONS
The fan does not respond to button controls.
The appliance is not connected to the power. Plug into the power socket completely before turning it on.
The fuse cover may be open. Disconnect the plug from outlet and close the cover of the fuse.
9
hOme™ offers a limited two-year warranty (“warranty period”) on all of our products purchased new and unused from hOme Technologies, LLC or an authorized reseller, with an original proof of purchase and where a defect has arisen, wholly or substantially, as a result of faulty manufacture, parts or workmanship during the warranty period. The warranty does not apply where damage is caused by other factors, including without limitation: (a) normal wear and tear; (b) abuse, mishandling, accident, or failure to follow operating instructions; (c) exposure to liquid or infiltration of foreign particles; (d) servicing or modifications of the product other than by hOme™ ; (e) commercial or non-household use.
The hOme™ warranty covers all costs related to restoring the proven defective product through repair or replacement of any defective part and necessary labor so that it conforms to its original specifications. A replacement product may be provided instead of repairing a defective product. hOme™
’s exclusive obligation under this warranty is limited to such repair or replacement.
A receipt indicating the purchase date is required for any claim, so please keep all receipts in a safe place. We recommend that you register your product on our website, homelabs.com/reg. Although greatly appreciated, the product registration is not required to activate any warranty and product registration does not eliminate the need for the original proof of purchase. The warranty becomes void if attempts at repair are made by non-authorized third parties and/or if spare parts, other than those provided by hOme™ , are used. You may also arrange for service after the warranty expires at an additional cost.
These are our general terms for warranty service, but we always urge our customers to reach out to us with any issue, regardless of warranty terms. If you have an issue with a hOme™ product, please contact us at 1-800-898-3002, and we will do our best to resolve it for you.
This warranty gives you specific legal rights, and you may have other legal rights which vary from state to state, country to country or province to province. The customer may assert any such rights at their sole discretion.
HME020234N
Warranty
Manufacturing Info
This manual is to be used with all items with the model number
SKU# : HME020234NRated voltage/Frequency: 120V~ 60Hz 0.4A
Keep all plastic bags away from children.
Warning
Contact Us
homelabs.com/chatMon–Fri 10AM–5PM EST
1-(800)-898-3002Mon–Fri 10AM–5PM EST
[email protected] within twelve hours
CHAT W ITH US CALL U S EMAIL US
© 2016 hOme Technologies, LLC37 East 18 Street, 7th FloorNew York, NY 10003
For household Use Only
[email protected]/help
All rights reserved, hO
me
®. Printed in China.