DESA = 5 x 106 ESA'SNOT TO SCALE
PAVEMENT TYPE 1DESIGN SUBGRADE CBR 10%
50mm AC14 (A15E) SURFACING
145mm AC20 (AR450) BASE10mm C170 SEAL ON AMC0 PRIME150mm DGS20 UNBOUND GRANULAR SUBBASECOURSE MODIFIED WITH CEMENT (UCS = 1.5MPa)
DESA = 3 x 106 ESA'SNOT TO SCALE
PAVEMENT TYPE 2DESIGN SUBGRADE CBR 10%
50mm AC14 (A15E) SURFACING
130mm AC20 (AR450) BASE10mm C170 SEAL ON AMC0 PRIME150mm DGS20 UNBOUND GRANULAR SUBBASECOURSE MODIFIED WITH CEMENT (UCS = 1.5MPa)
DESA = 6 x 106 ESA'SNOT TO SCALE
PAVEMENT TYPE 3DESIGN SUBGRADE CBR 10%
50mm AC14 (A15E) SURFACING
150mm AC20 (AR450) BASE10mm C170 SEAL ON AMC0 PRIME150mm DGS20 UNBOUND GRANULAR SUBBASECOURSE MODIFIED WITH CEMENT (UCS = 1.5MPa)
PAVEMENT NOTES1. ALL DRIVEWAYS TO BE PLAIN CONCRETE TO THE EXTENTS SHOWN,
UNLESS NOTED OTHERWISE.2. AREAS SHOWN ARE EQUAL TO HATCHED SURFACING LAYER SHOWN
ON PLANS. BASE AND SUBBASE LAYER ARE NOT INCLUDED IN THESEAREAS. REFER TO TYPICAL SECTION PLANS FOR PAVEMENT LAYERINGARRANGEMENT.
200mm STEEL FIBRE REINFORCED CONCRETE PAVEMENT
NOT TO SCALE
CONCRETE APRONDESIGN SUBGRADE CBR 10%
100mm REINFORCED, PATTERNED, COLOURED CONCRETE. 25MPA/20 SL62 MESH CENTRALLYPLACED. PATTERN AND COLOUR TO BE ALTERNATING WAVES OF EXPOSED GRAVEL - BELONGILWHITE AND WOODY HEAD BROWN (COOMERA). FINAL ARRANGEMENT TO BE AS DIRECTED BYSUPERINTENDENT ON SITE. NON-SLIP GLOSS, LONG LIFE SEAL COAT.50mm MIN. BEDDING SAND
NOT TO SCALE
CONCRETE MEDIAN INFILL
150mm PLAIN CONCRETE FOOTPATH, WIDTH AS SHOWN.(REFER NORTHERN RIVERS STD DRG'S FOR DETAILS)
50mm BEDDING SAND
NOT TO SCALE
CONCRETE FOOTPATHS/DRIVEWAYS/KERBRAMPS DESIGN SUBGRADE CBR 10%
(REFER LANDSCAPE DRGS.)TURF
(REFER LANDSCAPE DRGS.)MULCH/PLANTS
NOT TO SCALE
PAVEMENT TYPE 4DESIGN SUBGRADE CBR 10%
DESA = 3 x 105 ESA'SNOT TO SCALE
130mm DGB20 UNBOUND GRANULAR BASE
50mm AC14 (A15E) SURFACING
150mm DGS20 UNBOUND GRANULAR SUBBASE
10mm C170 SEAL ON AMC0 PRIME
150mm DGS20 UNBOUND GRANULAR SUBBASECOURSE MODIFIED WITH CEMENT (UCS = 1.5MPa)
(REFER LANDSCAPE DRGS.)GRASS (HYDROMULCH)
100mm MULCH
REMOVE EXISTING PAVEMENT MATERIAL, AS REQUIRED.ADD TOPSOIL, THICKNESS AS REQUIRED.
PAVEMENT JOINT TO EXISTING
EXISTING PAVEMENT
NEW SUBBASE COURSE
NEW SURFACING
150mm
LIMIT
OF
WOR
KSNO
MINA
TED
ON P
LANS
50mm
SAW
CUT
FULL
DEP
TH S
AWCU
T
NEW BASE COURSE
300mm SELF ADHESIVE BITUMENIMPREGNATED GEOTEXTILE (EG BITAC)
5000m2 (REFER NOTE 2)
7315m2 (REFER NOTE 2)
2195m2 (REFER NOTE 2)
690m2 (REFER NOTE 2)
285m2
3760m2
4165m2
6580m2
3845m2
385m2
GHD STANDARD A1 ATTRIBUTE BLOCK CAD File No.: GHD_G_0045_T Updated: 08-07-03 Version: 1.1
This Drawing must not be
used for Construction unless
signed as Approved
GHD STANDARD A1 SHEET CAD File No.: GHD_G_0045 Updated: 08-07-03 Version: 1.1
Date
Check
Drafting
DateDrawnRevisionNo
A1
Rev:Drawing No:
Original Size
Title
Project
Client
Check
DesignerDrawn
Scale
Design
Conditions of Use.
This document may only be used by
GHD's client (and any other person who
GHD has agreed can use this document)
for the purpose for which it was prepared
and must not be used by any other
person or for any other purpose.
DO NOT SCALE
Note: * indicates signatures on original issue of drawing or last revision of drawing
Level 13 The Rocket
203 Robina Town Centre Drive
QLD 4226 Australia
T 61 7 5557 1000 F 61 7 5557 1099
E [email protected] W www.ghd.com
Plot Date: Cad File No:4 February 2019 - 2:55 PM G:\41\29578\CADD\Drawings\41-29578-C301_C308.dwg
Plotted by:
Jack Simmonds
(Project Director)
Approved
Job
Manager
Project
Director
BYRON SHIRE COUNCIL
BYRON BAY BYPASS
PAVEMENT AND SURFACE TYPE LAYOUTS
LEGEND
41-29578-C301
2
M.MASON B. COLLISTER
B. COLLISTER* R. BLUMSON*
A. OLIVER*
25/11/2016
AS SHOWN
0 ISSUED FOR CONSTRUCTION MM CS* AO* 25/11/16
1 CADASTRAL SURVEY BDY & SEPP14 WETLANDS EXTENT ADDED MM CS* AO* 11/04/17
2 FACILITATE PROPOSED BUS INTERCHANGE JS RB* CS* 04/02/19
STORMWATER PIT
VEHICULAR CROSSING
RAMPED KERB CROSSING
STORMWATER MANHOLE
STREET LIGHT AND POLE
BOLLARD
STORMWATER HEADWALL
STONE PITCHING
STREET TREE(FOR DETAILS REFERLANDSCAPE DRGS.)
BARRIER KERB (MODIFIED TYPE B2) UPRIGHT KERB AND CHANNEL (TYPE B1)
RETAINING WALL
SEMI MOUNTABLE KERB (TYPE B5)
PEDESTRIAN FENCE
BATTER SLOPE
(TYPE 1 VERGE )NOISE BARRIERFAUNA EXCLUSION FENCE
LEGEND DESIGN SYMBOLS AND FEATURES
DOUBLE GATE
SEMI MOUNTABLE KERB (MODIFIED TYPE SM3)
SUBSOIL DRAIN (> FLOW DIRECTION) SSD V
GIS PROPERTY BOUNDARYCADASTRAL SURVEYPROPERTY BOUNDARYSEPP14 WETLANDS EXTENTEXTENT OF DESIGN TO BE SUPERSEDEDBY PROPOSED BUS INTERCHANGE.DESIGN BY OTHERS
N
WENTW
ORTH
STRE
ET
ROAD
RES
ERVE
GLEN VILLARESORT
BUTLER STREET
LIMIT OF WORKS (CH.32.477)LOT 11DP 758207
LOT 12DP 758207
LOT 3DP 38981
LOT 4DP 38981
LOT 5DP 38981
LOT 13DP 758207
LOT 184DP 755695
|||||| |||||| ||||||
GHD STANDARD A1 ATTRIBUTE BLOCK CAD File No.: GHD_G_0045_T Updated: 08-07-03 Version: 1.1
This Drawing must not be
used for Construction unless
signed as Approved
GHD STANDARD A1 SHEET CAD File No.: GHD_G_0045 Updated: 08-07-03 Version: 1.1
Date
Check
Drafting
DateDrawnRevisionNo
A1
Rev:Drawing No:
Original Size
Title
Project
Client
Check
DesignerDrawn
Scale
Design
Conditions of Use.
This document may only be used by
GHD's client (and any other person who
GHD has agreed can use this document)
for the purpose for which it was prepared
and must not be used by any other
person or for any other purpose.
DO NOT SCALE
Note: * indicates signatures on original issue of drawing or last revision of drawing
Level 13 The Rocket
203 Robina Town Centre Drive
QLD 4226 Australia
T 61 7 5557 1000 F 61 7 5557 1099
E [email protected] W www.ghd.com
Plot Date: Cad File No:4 February 2019 - 2:58 PM G:\41\29578\CADD\Drawings\41-29578-L001_L010.dwg
Plotted by:
Jack Simmonds
(Project Director)
Approved
Job
Manager
Project
Director
BYRON SHIRE COUNCIL
BYRON BAY BYPASS
LANDSCAPING LAYOUT
SHEET 4 OF 10
41-29578-L004
0
S. DA-RE S. DA-RE
S. DA-RE* S. DA-RE*
A. OLIVER*
09/12/16
AS SHOWN
0 ISSUED FOR CONSTRUCTION SDR CS* AO* 09/12/16
0 2.5 10 12.5m7.55
SCALE 1:250 AT ORIGINAL SIZE
FOR
CONT
INUA
TION
REF
ER D
RAW
ING
41-2
9578
-L00
3
FOR
CONT
INUA
TION
REF
ER D
RAW
ING
41-2
9578
-L00
5
C
PO B ox 14 7 3 B a l l i na N SW 2 47 8T e l e p h o n e 0 4 2 8 2 5 9 2 8 6w w w . d e s i g n t e a m i n k . c o m
design team ink
landscape architecture urban design
1. REFER TO GHD DRAWINGS 41-29578-C101 TO C107 FORTREE REMOVAL AND THE LOCATION OF SERVICES
2. REFER TO LEGEND ON GHD DRAWING SHEET 41-29578-C301
NOTE
Mass planting of 2500
Lomandra hystrix (native
tubes) to embankment
between chainages 672
and 1000 (@2.5 plants/m²)
Plant a single row of Lomandra
hystrix (native tubes) (qty 876) to
edge of pathway between chainage
672 and 1110 (@ 2 plants/lin.m)
Grass (hydromulch)
1 Grevillea
'Moonlight'
1 Banksia
integrifolia
1 Grevillea
'Moonlight'
1 Banksia
integrifolia
1 Waterhousea
floribunda (true form)
Turf base
of swale
Hydromulch
batter
Turf batters and
base of swale
Take care to protect existing
trees and shrubs, their roots
and canopy, along the road
verge
Take care to protect existing
trees and shrubs, their roots
and canopy, along the road
verge
Turf
Turf
Turf
Turf
Turf
Turf
Turf
CH
67
2
N
BUTLER STREET
GLEN VILLARESORT
LOT 184DP 755695
LOT 186DP 755695
GHD STANDARD A1 ATTRIBUTE BLOCK CAD File No.: GHD_G_0045_T Updated: 08-07-03 Version: 1.1
This Drawing must not be
used for Construction unless
signed as Approved
GHD STANDARD A1 SHEET CAD File No.: GHD_G_0045 Updated: 08-07-03 Version: 1.1
Date
Check
Drafting
DateDrawnRevisionNo
A1
Rev:Drawing No:
Original Size
Title
Project
Client
Check
DesignerDrawn
Scale
Design
Conditions of Use.
This document may only be used by
GHD's client (and any other person who
GHD has agreed can use this document)
for the purpose for which it was prepared
and must not be used by any other
person or for any other purpose.
DO NOT SCALE
Note: * indicates signatures on original issue of drawing or last revision of drawing
Level 13 The Rocket
203 Robina Town Centre Drive
QLD 4226 Australia
T 61 7 5557 1000 F 61 7 5557 1099
E [email protected] W www.ghd.com
Plot Date: Cad File No:4 February 2019 - 2:58 PM G:\41\29578\CADD\Drawings\41-29578-L001_L010.dwg
Plotted by:
Jack Simmonds
(Project Director)
Approved
Job
Manager
Project
Director
BYRON SHIRE COUNCIL
BYRON BAY BYPASS
LANDSCAPING LAYOUT
SHEET 5 OF 10
41-29578-L005
0
S. DA-RE S. DA-RE
S. DA-RE* S. DA-RE*
A. OLIVER*
09/12/16
AS SHOWN
0 ISSUED FOR CONSTRUCTION SDR CS* AO* 09/12/16
0 2.5 10 12.5m7.55
SCALE 1:250 AT ORIGINAL SIZE
FOR
CONT
INUA
TION
REF
ER D
RAW
ING
41-2
9578
-L00
4
FOR
CONT
INUA
TION
REF
ER D
RAW
ING
41-2
9578
-L00
6
C
P O B ox 1 4 7 3 B a l l i na NS W 2 47 8T e l e p h o n e 0 4 2 8 2 5 9 2 8 6w w w . d e s i g n t e a m i n k . c o m
design team ink
landscape architecture urban design
1. REFER TO GHD DRAWINGS 41-29578-C101 TO C107 FORTREE REMOVAL AND THE LOCATION OF SERVICES
2. REFER TO LEGEND ON GHD DRAWING SHEET 41-29578-C301
NOTE
Continued mass planting as
specified on previous sheet
Take care to protect existing
trees and shrubs, their roots
and canopy, along the road
verge
Take care to protect existing
trees and shrubs, their roots
and canopy, along the road
verge
Continue planting as
specified on previous sheet
Grass (hydromulch)
Turf base
of swale
Hydromulch
batter
Turf
Hydromulch
batter
Turf
Turf
Turf
Turf
Grass (hydromulch)
Grass (hydromulch)
Hydromulch
batter
N
BUTLER STREET
RAILW
AY LI
NE (N
OT U
SED)
NORT
H CO
AST
LOT 186DP 755695
LOT 6DP 258071
LOT 7DP 258071
LOT 8DP 818197
LOT 9DP 818197
SP 83280
|| | | | | | | | | | | | | | | | |
GHD STANDARD A1 ATTRIBUTE BLOCK CAD File No.: GHD_G_0045_T Updated: 08-07-03 Version: 1.1
This Drawing must not be
used for Construction unless
signed as Approved
GHD STANDARD A1 SHEET CAD File No.: GHD_G_0045 Updated: 08-07-03 Version: 1.1
Date
Check
Drafting
DateDrawnRevisionNo
A1
Rev:Drawing No:
Original Size
Title
Project
Client
Check
DesignerDrawn
Scale
Design
Conditions of Use.
This document may only be used by
GHD's client (and any other person who
GHD has agreed can use this document)
for the purpose for which it was prepared
and must not be used by any other
person or for any other purpose.
DO NOT SCALE
Note: * indicates signatures on original issue of drawing or last revision of drawing
Level 13 The Rocket
203 Robina Town Centre Drive
QLD 4226 Australia
T 61 7 5557 1000 F 61 7 5557 1099
E [email protected] W www.ghd.com
Plot Date: Cad File No:4 February 2019 - 2:59 PM G:\41\29578\CADD\Drawings\41-29578-L001_L010.dwg
Plotted by:
Jack Simmonds
(Project Director)
Approved
Job
Manager
Project
Director
BYRON SHIRE COUNCIL
BYRON BAY BYPASS
LANDSCAPING LAYOUT
SHEET 6 OF 10
41-29578-L006
0
S. DA-RE S. DA-RE
S. DA-RE* S. DA-RE*
A. OLIVER*
09/12/16
AS SHOWN
0 ISSUED FOR CONSTRUCTION SDR CS* AO* 09/12/16
0 2.5 10 12.5m7.55
SCALE 1:250 AT ORIGINAL SIZE
FOR CONTINUATION REFER DRAWING 41-29578-L005
FOR
CONT
INUA
TION
REF
ER D
RAW
ING
41-2
9578
-L00
7
C
P O B o x 14 7 3 B a l l i n a N S W 2 4 78T e l e p h o n e 0 4 2 8 2 5 9 2 8 6w w w . d e s i g n t e a m i n k . c o m
design team ink
landscape architecture urban design
1. REFER TO GHD DRAWINGS 41-29578-C101 TO C107 FORTREE REMOVAL AND THE LOCATION OF SERVICES
2. REFER TO LEGEND ON GHD DRAWING SHEET 41-29578-C301
NOTE
Take care to protect all
existing trees and shrubs,
their roots and canopy,
along the road verge
Take care to protect existing
trees and shrubs, their roots
and canopy, along the road
verge
285 Crinum pedunculatum
(@ 2.5 plants/m²)
220 Carpobrotus
glaucescens 'Edna Walling'
(@ 2.5 plants/m²)
60 Carpobrotus glaucescens
'Edna Walling' (@ 3 plants/m²)
64 Lomandra 'Lime tuff'
(@ 4 plants/m²)
42 Crinum pedunculatum
(centrally) (@ 3 plants/m²)
Continued mass planting as
specified on previous sheet
Turf base
of swale
Hydromulch to
limit of works
Hydromulch
batters to limit of
works
Grass
(hydromulch)
Turf
277 Lomandra hystrix
(@ 2 plants/m²)
Continued mass planting as
specified on previous sheet
Mass plant 455
Lomandra hystrix (@ 2.5
plants/m²)
2 x Cupaniopsis
anacardioides
planted in grass
verge
Turf
Turf
1 Waterhousea floribunda (true
form) planted centrally. Install
900mm root redirector to back of
roundabout kerb in accordance
with manufacturer's
recommendations.
Turf
Turf
Turf
CH
10
50
CH1000
CH
11
00
GHD STANDARD A1 ATTRIBUTE BLOCK CAD File No.: GHD_G_0045_T Updated: 08-07-03 Version: 1.1
This Drawing must not be
used for Construction unless
signed as Approved
GHD STANDARD A1 SHEET CAD File No.: GHD_G_0045 Updated: 08-07-03 Version: 1.1
Date
Check
Drafting
DateDrawnRevisionNo
A1
Rev:Drawing No:
Original Size
Title
Project
Client
Check
DesignerDrawn
Scale
Design
Conditions of Use.
This document may only be used by
GHD's client (and any other person who
GHD has agreed can use this document)
for the purpose for which it was prepared
and must not be used by any other
person or for any other purpose.
DO NOT SCALE
Note: * indicates signatures on original issue of drawing or last revision of drawing
Level 13 The Rocket
203 Robina Town Centre Drive
QLD 4226 Australia
T 61 7 5557 1000 F 61 7 5557 1099
E [email protected] W www.ghd.com
Plot Date: Cad File No:4 February 2019 - 2:59 PM G:\41\29578\CADD\Drawings\41-29578-L001_L010.dwg
Plotted by:
Jack Simmonds
(Project Director)
Approved
Job
Manager
Project
Director
BYRON SHIRE COUNCIL
BYRON BAY BYPASS
LANDSCAPE DETAILS AND SPECIFICATIONS
SHEET 8 OF 10
41-29578-L008
0
S. DA-RE S. DA-RE
S. DA-RE* S. DA-RE*
A. OLIVER*
09/12/16
AS SHOWN
0 ISSUED FOR CONSTRUCTION SDR CS* AO* 09/12/16
01
-
PLANTING AREA (SLOPE<1:4)
Ensure that the top of the mulch in garden areas is flush
with adjacent surfaces, below weepholes and with
adequate setdowns to termite barriers (usually 75mm).
x
2x
SECTION
03
-
TYPICAL TURFING
Ensure that the top of turf is flush with
adjacent surfaces (kerbs, edges etc), below
weepholes and with adequate setdowns to
termite barriers. Topdress to fill any joints or
voids and achieve a smooth finished profile.
Section
C
P O B o x 1 47 3 B a l l i n a N S W 2 4 7 8T e l e p h o n e 0 4 2 8 2 5 9 2 8 6w w w . d e s i g n t e a m i n k . c o m
design team ink
landscape architecture urban design
Typical Section (1:200)
Minimum offset 1.0m
ROOTBALL
3 (no.) 1800x50x50mm (min.) hardwood stakes.
Drive stakes at least 600mm into ground clear of
rootball.
Hessian or rubber ties min. 100mm wide wrapped
in figure of eight around trunk. Ties should allow
the tree to be self supporting and provide
additional support during wind or storm events.
100mm thickness of mulch pulled at least 100mm
away from trunk of tree.
Backfill with imported garden soil. Add slow
release fertilser to the soil mix as recommended
by the manufacturer and as suitable for the plant
species.
Form a firm base from 50% imported
garden soil and 50% cultivated site soil
for the tree
Cultivate the subsoil to 300mm depth
Tree (installed plumb)
Prior to planting remove all
grass (and it's roots) from
the entire area to be
planted and mulched
GRASS VERGE
Form a recessed
spade edge
'X' m
Twice 'X' m
30
0m
m
If fill material is present, remove
fill to a minimum depth of 400mm
and replace with stockpiled site
topsoil or imported garden soil.
04
-
TYPICAL TREE PLANTING IN GRASS VERGE
CONCRETE SHARED PATHWAY
Minimum Offset 1.0m0.5m
CO
NC
RE
TE
S
HA
RE
D P
AT
HW
AY
Form a recessed
spade edge
Plan View
GRASS VERGE
GRASS VERGE
1.0m
Turf sod ('A-grade) - Install turf across the
contours with staggered and close butted joints.
100mm depth of topsoil mix
Cultivated subgrade to a depth of 200mm to
loosen soil and remove hardpans and glazings
02
-
PLANTING AREA (SLOPE = 1:4)
Ensure that the top of the mulch in garden areas is flush
with adjacent surfaces, below weepholes and with
adequate setdowns to termite barriers (usually 75mm).
100mm depth of mulch. Pull the
mulch away from the base of each
plant.
Backfill planting holes with imported
garden soil and fertiliser to suit the
plant species
Cultivated site soil
1
4 max
x
2x
100mm depth of mulch. Pull the
mulch away from the base of each
plant.
Backfill planting holes with imported
garden soil and fertiliser to suit the
plant species
Cultivated site soil
Plants
installed
plumb
If fill material is present, remove
fill to a minimum depth of 400mm
and replace with stockpiled site
topsoil or imported garden soil.
Check for services
prior to excavation
MULCH
Clear of services
Clear of services
Existing ground
GHD STANDARD A1 ATTRIBUTE BLOCK CAD File No.: GHD_G_0045_T Updated: 08-07-03 Version: 1.1
This Drawing must not be
used for Construction unless
signed as Approved
GHD STANDARD A1 SHEET CAD File No.: GHD_G_0045 Updated: 08-07-03 Version: 1.1
Date
Check
Drafting
DateDrawnRevisionNo
A1
Rev:Drawing No:
Original Size
Title
Project
Client
Check
DesignerDrawn
Scale
Design
Conditions of Use.
This document may only be used by
GHD's client (and any other person who
GHD has agreed can use this document)
for the purpose for which it was prepared
and must not be used by any other
person or for any other purpose.
DO NOT SCALE
Note: * indicates signatures on original issue of drawing or last revision of drawing
Level 13 The Rocket
203 Robina Town Centre Drive
QLD 4226 Australia
T 61 7 5557 1000 F 61 7 5557 1099
E [email protected] W www.ghd.com
Plot Date: Cad File No:4 February 2019 - 2:59 PM G:\41\29578\CADD\Drawings\41-29578-L001_L010.dwg
Plotted by:
Jack Simmonds
(Project Director)
Approved
Job
Manager
Project
Director
BYRON SHIRE COUNCIL
BYRON BAY BYPASS
LANDSCAPE DETAILS AND SPECIFICATIONS
SHEET 9 OF 10
41-29578-L009
1
S. DA-RE S. DA-RE
S. DA-RE* S. DA-RE*
A. OLIVER*
09/12/16
AS SHOWN
0 ISSUED FOR CONSTRUCTION SDR CS* AO* 09/12/16
1 FACILITATE PROPOSED BUS INTERCHANGE JS RB* CS* 04/02/19
C
P O B o x 1 47 3 B a l l i n a N S W 2 4 78T e l e p h o n e 0 4 2 8 2 5 9 2 8 6w w w . d e s i g n t e a m i n k . c o m
design team ink
landscape architecture urban design
Typical Section (1:200)
Typically min. 5.8m from back of kerb (7.93m from edge of traffic lane)
ROOTBALL
3 (no.) 1800x50x50mm (min.) hardwood stakes.
Drive stakes at least 600mm into ground clear of
rootball.
Hessian or rubber ties min. 100mm wide wrapped
in figure of eight around trunk. Ties should allow
the tree to be self supporting and provide
additional support during wind or storm events.
100mm thickness of mulch pulled at least 100mm
away from trunk of tree.
Backfill with imported garden soil. Add slow
release fertilser to the soil mix as recommended
by the manufacturer and as suitable for the plant
species.
Edge of excavation for tree
Form a firm base from 50% imported
garden soil and 50% cultivated site soil
for the tree
Cultivate the subsoil to 300mm depth
Tree (installed plumb) on
consistent alignment
Prior to planting remove all
grass (and it's roots) from
the entire area to be
planted and mulched
CONCRETE SHARED PATHWAY
'X' m
Twice 'X' m
30
0m
m
05
-
TYPICAL TREE PLANTING IN PLANTED VERGE ON BATTER (1:4)
Top o
f batt
er
Stre
et lig
ht an
d foo
ting b
eyon
d
Edge
of fo
otpath
PLANTING
AREA
Back
of K
erb
BATTER
PLANTING
AREA
Offset garden
plantings 0.5m
from pathway
edge
PLANT SCHEDULE
Botanical Name (Common Name) Mature Ht Min. Stock Size Quantity
Trees
Banksia integrifolia (Coast banksia) 8m 200 litre 7
Cupaniopsis anacardioides (Tuckeroo) 6m 200 Litre 3
Melaleuca quinquenervia (Broad leaf paper bark) 12-15m 200 Litre 8
Waterhousea floribunda (Weeping lilly pilly) 8-10m 300 Litre 2
Shrubs
Alectryon coriaceus (Beach alectryon) 2m 300mm pot 1
Austromyrtus dulcis (Midgen berry) 1m 200mm pot 121
Crinum pedunculatum (Swamp lilly) 1m 200mm pot 573
Grevillea 'Moonlight' (a grevillea) 3-4m 300mm pot 2
Groundcovers
Carpobrotus glaucescens 'Edna Walling' (Pigs face)Prostrate 140mm pot 470
Dianella revoluta 'Little rev' 0.4m 140mm pot 312
Lomandra hystrix (Matt rush) 1.0m 140mm pot 732
Lomandra hystrix (native tubes) (Matt rush) 1.0m 100mm pot 5826
Lomandra 'Lime tuff' (a cultivar matt rush) 0.5m 140mm pot 731
Check for services
prior to excavation
Existing ground
GHD STANDARD A1 ATTRIBUTE BLOCK CAD File No.: GHD_G_0045_T Updated: 08-07-03 Version: 1.1
This Drawing must not be
used for Construction unless
signed as Approved
GHD STANDARD A1 SHEET CAD File No.: GHD_G_0045 Updated: 08-07-03 Version: 1.1
Date
Check
Drafting
DateDrawnRevisionNo
A1
Rev:Drawing No:
Original Size
Title
Project
Client
Check
DesignerDrawn
Scale
Design
Conditions of Use.
This document may only be used by
GHD's client (and any other person who
GHD has agreed can use this document)
for the purpose for which it was prepared
and must not be used by any other
person or for any other purpose.
DO NOT SCALE
Note: * indicates signatures on original issue of drawing or last revision of drawing
Level 13 The Rocket
203 Robina Town Centre Drive
QLD 4226 Australia
T 61 7 5557 1000 F 61 7 5557 1099
E [email protected] W www.ghd.com
Plot Date: Cad File No:4 February 2019 - 2:59 PM G:\41\29578\CADD\Drawings\41-29578-L001_L010.dwg
Plotted by:
Jack Simmonds
(Project Director)
Approved
Job
Manager
Project
Director
BYRON SHIRE COUNCIL
BYRON BAY BYPASS
LANDSCAPE DETAILS AND SPECIFICATIONS
SHEET 10 OF 10
41-29578-L010
0
S. DA-RE S. DA-RE
S. DA-RE* S. DA-RE*
A. OLIVER*
09/12/16
AS SHOWN
0 ISSUED FOR CONSTRUCTION SDR CS* AO* 09/12/16
GENERAL ITEMS
GENERAL
SURVEY: Do not disturb any permanent or other survey marks found on, or near
the site, as part of the work. Any survey marks that are destroyed during the work
are required to be reinstated by a Registered Surveyor at the contractor's expense
and as required by the Project Manager and Regulations.
EXISTING SERVICES: This plan does not show all underground services. The true
location of underground services should be determined on site prior to excavations.
Rectification of any service that is required as a result of damage caused by the
contractor or their sub-contractors is the responsibility of the contractor.
PLAN COMPLIANCE: Work not constructed in accordance with the plans or by an
approved variation may be rejected. If works are rejected the contractor will be
required to rectify the defective or non-complying work.
PROTECTION OF EXISTING TREES AND PLANTS
PROTECTION
Care should be taken at all times to minimise damage to all trees which are to be
retained, as well as to any native shrub or groundcover plants where possible.
Do not dispose of any chemicals, waste, paints or other building products within the
dripline of any tree or plant which is to be retained. Do not park any machinery or
vehicles within the drip line of any tree or plant to be retained. Do not store any
materials or equipment within the dripline of the trees. If damage is incurred to a
tree to be retained, the contractor shall provide a new tree of a similar size and of the
correct local genetic origin to replace the existing tree at their own expense.
FENCING
Prior to commencing any construction work at the site, install temporary fencing
outside the dripline (where possible) of the trees within the work area which are to be
retained. Where work is to occur within the dripline of a tree, temporarily remove the
smallest section of fence required to do the work, undertake the work with care and
reinstate the fence immediately upon completion.
The fence is to be constructed as follows:
- with a minimum height of 1.2m
- outside the dripline of the tree/s where construction work does not occur within the
dripline
- with steel star pickets at a maximum distance of 2m between pickets (include
picket caps)
- with a minimum of 3 strands of tensioned steel wire
- to fully enclose the tree/s and
- with orange barrier mesh, or similar, attached to the outside of the fence and
continuing around its perimeter.
The fence shall be maintained to it's full height and in good condition for the duration
of the site clearing, preparation and construction works.
WEED REMOVAL
WEED ERADICATION: Remove all weeds (including grass, weed vines and garden
plantings) within areas to be planted. Use the correct technique to prevent regrowth
of the weed and plant species. All weed matter shall be removed from the site and
disposed of at a legal waste or composting facility.
PLANTS AND PLANTING
PLANT TYPES: All plants shall be of the species specified on the drawings. If the species
specified can not be obtained, contact the Project Manager prior to ordering or purchasing
substitutes.
PLANT PROVENANCE: All specified native plant species shall be grown from seed collected
from local vegetation communities, and be of local genetic provenance.
PLANT CONDITION: Plant stock shall be of the sizes specified in the Plant Schedule (as a
minimum). Plant stock shall be:
· well established and have a healthy straight tap root (as applicable) and well established
fibrous root system which shows no evidence of being restricted or damaged;
· be sun hardened and suitable for planting in the specific microclimate of the site;
· show no evidence of pest, insect or disease damage.
INSPECTION: All plant stock shall be delivered to site in a holding area and inspected by the
project manager prior to planting. Any plants rejected by the Project Manager due to poor
quality, form or incorrect species will need to be replaced by the Contractor.
TREE REQUIREMENTS
TYPES: All trees shall be true to the type of species specified and each tree clearly labeled
with a tag showing the species name (including variety or cultivar name).
HEALTH AND VIGOUR: The foliage size, texture and colour at the time of delivery must be
consistent with the size texture and colour exhibited by health specimens of the same species.
PESTS AND DISEASE: Foliage and roots shall be free from evidence of attack by pests or
insects, fungal diseases or rot.
GENERAL FORM: All tree species shall be self-supporting. The caliper at any given point on
the stem or trunk must be greater than the caliper at any higher point on the stem or trunk.
Street trees shall have a clean stem height of at least 30% of the total height of the tree and no
more than 40% of the total tree height. Any pruned limbs must be clean cut at the collar and no
more than 20% of pruned limbs shall have been recently cut (non-calloused). The distance
from the centre of the trunk to the extremity of the rootball must not vary by more than 10%.
CROWN FORM: All trees shall have a balanced crown with the difference in crown distribution
on opposite sides of the stem axis not exceeding 20%.
ROOT FORM AND HEALTH: For trees in containers greater than 45 Ltr or ex-ground tree
stock with a size index greater than 70 (as measured in accordance with NATSPEC (Clark,
2006, Specifying Trees, A Guide to Assessment of Tree Quality'), roots within the outer 50% of
the rootball must have undergone primary division at not more than 100mm intervals. Roots,
from the point of initiation, must generally grow in an outwards (radial) or downwards direction.
Any deviation from the established direction shall not exceed 45 degrees. All rootballs shall
not exceed 550mm depth. The root crown must be at the surface of the rootball.
SOIL
SOIL IN GARDEN AREAS: All garden areas, shall use imported garden soil to a minimum
depth of 300mm or as otherwise detailed. All excavations for planting shall be backfilled with
imported garden soil.
Imported garden soil must be a 'premium quality' landscape /garden mix and:
· be of a friable and porous nature,
· contain no refuse or material toxic to plant growth,
· be free of extraneous matter (stones, lumps, root matter or sticks) larger than 20mm in
size,
· have an organic matter content of at least 25% by mass,
· have a pH between 5-7,
· have an EC of 0.4-1.0
· be suitable for phosphorus sensitive plants.
The soil shall consist of the following approximate components, 50-60% red soil and sandy
loam, 10-15% coarse sand and 25-30% compost (including at least 5% mushroom compost).
A certificate from the supplier certifying the soils properties may be requested.
SOIL IN TURF AREAS: Soil for turf areas must be a 'Turf Underlay' soil consisting of 65-70%
double washed sand and 30-35% screened nitrohumus fines or similar. PH shall be between 6
and 7. Add a specialist turf grass fertiliser after laying the turf or as recommended by the
fertiliser manufacturer.
SOIL FOR TOPDRESSING GRASS AND TURF AREAS: Soil for topdressing must be an organic
topdressing soil or similar lawn topdressing soil consisting of 10-15% double washed sand,
50-60% soil, 30% composted organics and a complete fertiliser. PH shall be between 6 and 7.
MULCH
MULCH TYPE: 'coarse Tea-tree' mulch or equivalent. The mulch shall be formed from 100 percent
recycled wood waste, have a pH between 5.5 and 7.0. Ensure the mulch does not contain more
than 5 percent fines. Ensure that the mulch is free of seed and deleterious matter.
GENERAL MULCHING REQUIREMENTS: Mulch the entire garden area to the depths shown in
the details (after settlement). Pull the mulch away from the trunk/base of all plants. Ensure mulch
finishes at least 75mm below the weepholes and any termite barrier protection of buildings or
walls. Grade all garden areas away from buildings and towards drainage pits and lines, unless
otherwise shown by others.
TURFING
TYPE: Grade A 'Winter green' couch
INSTALLATION: Remove compacted fill material from areas to be turfed. Install 100mm minimum
depth of topsoil to create a smooth and consistent base. Keep turf moist at all times during
delivery and storage and lay it in its final position as soon as possible after delivery. Install the
turf sods across the land contour with staggered and close butted joints. Water turf deeply. Top
dress to fill any voids or gaps.
GRASS HYDROMULCH
PREPARATION: Remove fill material from the area to be mulched to a depth of 100mm. Install
topsoil to a minimum depth of 100mm after settlement not more than 2 days prior to mulching.
MIX: The hydromulch mix shall consist of the following components:
· Water
· Straw mulch (similar to Envirostraw plus) 3000kg/ha
· Binder (similar to Hydrogrip plus) 40kg/ha
· Green dye (similar to Green malachite crystals) 1kg/ha
· Japanese millet (September to March) 35kg/ha or Rye Corn (April to August) 25kg/ha
· Zoysia 20kg/ha
· Themeda 15kg/ha
APPLICATION: Agitate continuously the slurry to maintain a uniform consistency during
application. Apply it uniformly over the whole surface. The sprayed hydromulch layer within 48
hours of application must have a minimum thickness at any location of 5 mm when using sugar
cane mulch (mixed with shredded paper), or 2 mm when using wood fibre.
MAINTENANCE NOTES
MAINTENANCE PERIOD AND TASKS: All works shall be maintained for a period of 52 weeks
from the date of practical completion.
Maintenance shall include:
· replacement of failed, damaged or stolen plants at least 6 months prior to final completion and
again prior to final completion is required
· watering to maintain plants in a healthy and vigorously growing condition
· replenishment of soil and mulch to the design depths throughout the maintenance period
· pruning if required to maintain good form or safety
· regular removal of rubbish and litter
· weed treatment and removal undertaken on at least a monthly basis
· mowing to maintain a maximum grass height of 50mm
· pulling mulch away from the base of plants and from building weepholes
· pest and disease control
· fertilising if required to encourage growth
A log book or record of all maintenance work undertaken (date and tasks) shall be kept and made
available for inspection if requested. Final completion shall be granted when all maintenance
activities have been recently completed, pedestrian pavements cleaned, soils and mulches have
been topped up to design levels and depths, weeds removed and the site is in a neat and tidy
condition.
C
P O B o x 1 47 3 B a l l i n a N S W 2 4 78T e l e p h o n e 0 4 2 8 2 5 9 2 8 6w w w . d e s i g n t e a m i n k . c o m
design team ink
landscape architecture urban design