Service ManualContents
This service manual contains information of different types of models.Make sure to refer to the section describing your model.
TYPE A46PFL3608/F7 PHILIPS (Serial No.: DS1, DS2)
46PFL3908/F7 PHILIPS (Serial No.: DS1, DS2)
46PFL3908/F8 PHILIPS (Serial No.: XA1, XA2)
46PFL3608/F7 A PHILIPS (Serial No.: DS3)
TYPE B46PFL3708/F7 PHILIPS (Serial No.: DS1)
46PFL3708/F8 PHILIPS (Serial No.: XA1)
46” LCD TVchassis PL13.14
140224
© 2014 Funai Electric Co., Ltd.
All rights reserved. No part of this manual may be reproduced, copied, transmitted, disseminated, transcribed, downloaded or stored in any storage medium, in any form or for any purpose without the express prior written consent of Funai. Furthermore, any unauthorized commercial distribution of this manual or any revision hereto is strictly prohibited.
Information in this document is subject to change without notice. Funai reserves the right to change the content herein without the obligation to notify any person or organization of such changes.
with the design is a registered trademark of Funai Electric Co., Ltd and may not be used in any way without the express written consent of Funai. All other trademarks used herein remain the exclusive property of their respective owners. Nothing contained in this manual should be construed as granting, by implication or otherwise, any license or right to use any of the trademarks displayed herein. Misuse of any trademarks or any other content in this manual is strictly prohibited. Funai shall aggressively enforce its intellectual property rights to the fullest extent of the law.
This service manual contains information of different types of models.Make sure to refer to the section describing your model.
IMPORTANT SAFETY NOTICE
Proper service and repair is important to the safe, reliable operation of all P&F Equipment. The service procedures recommended by P&F and described in this service manual are effective methods of performing service operations. Some of these service special tools should be used when and as recommended.
It is important to note that this service manual contains various CAUTIONS and NOTICES which should be carefully read in order to minimize the risk of personal injury to service personnel. The possibility exists that improper service methods may damage the equipment. It also is important to understand that these CAUTIONS and NOTICES ARE NOT EXHAUSTIVE. P&F could not possibly know, evaluate and advice the service trade of all conceivable ways in which service might be done or of the possible hazardous consequences of each way. Consequently, P&F has not undertaken any such broad evaluation. Accordingly, a servicer who uses a service procedure or tool which is not recommended by P&F must first use all precautions thoroughly so that neither his safety nor the safe operation of the equipment will be jeopardized by the service method selected.
The LCD panel is manufactured to provide many years of useful life. Occasionally a few non active pixels may appear as a tiny spec of color. This is not to be considered a defect in the LCD screen.
TABLE OF CONTENTS
Specifications [TYPE A] . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1[TYPE B] . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-2
Important Safety Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-1Standard Notes for Servicing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-1Cabinet Disassembly Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-1Electrical Adjustment Instructions [TYPE A] . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-1
[TYPE B] . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-5How to Initialize the LCD TV . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-1Firmware Renewal Mode[TYPE A] . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-1
[TYPE B] . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-2Troubleshooting. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-1Block Diagrams [TYPE A] . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-1
[TYPE B] . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-6Schematic Diagrams / CBA and Test Points . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-1Wiring Diagrams [TYPE A] . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11-1
[TYPE B] . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11-2Exploded Views . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12-1Parts List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13-1Revision History . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14-1
1-1 PL13.14SP
SPECIFICATIONS
[TYPE A]< TUNER / NTSC >
ANT. Input ---------------------- 75 Ω Unbal., F type
< TUNER / ATSC >
< LCD PANEL >
< VIDEO >
< AUDIO >
All items are measured across 8 Ω load at speaker output terminal with L.P.F.
Description Condition Unit Nominal Limit
1. AFT Pull-In Range --- MHz ±2.3 ±2.1
2. Synchronizing Sens.TV.ch.4
CA.ch.31CA.ch.87
dBµVdBµVdBµV
181818
202023
Description Condition Unit Nominal Limit
1. Received Freq. Range (-28dBm) --- kHz --- ±100
2. ATSC Dynamic Range (min / max)ch.4
ch.10ch.41
dBmdBmdBm
---------
-76/0-76/0
-76/+4
Description Condition Unit Nominal Limit
1. Native Pixel Resolution HorizontalVertical
pixelspixels
19201080
------
2. Brightness (w / filter) --- cd/m2 300 ---
3. Viewing Angle HorizontalVertical
°°
-88 to 88-88 to 88
------
Description Condition Unit Nominal Limit
1. Over Scan HorizontalVertical
%%
55
5±55±5
2. Color Temperature
---xy
°K 120000.2720.278
---±5%±5%
<Measurement condition>Input signal: HDMI1 Raster (30/50/80IRE) 1080i@60Measurement point: Screen centerMeasuring instrument: Made of KONICA MINOLTA Luminance meter CA-310Aging time: 60min. (Retail MODE / 100IRE Raster HDMI
1080i@60)MODE setting of TV: Shipment setting / Retail MODEAmbient temperature: 25°C ±5°C
3. Resolution (composite video) HorizontalVertical
lineline
400350
------
Description Condition Unit Nominal Limit
1. Audio MAX Output (ATSC 0dBfs) Lch/Rch W 10.0/10.0 9.0/9.0
2. Audio Distortion (NTSC) 500mW: Lch/Rch % 0.5/0.5 2.0/2.0
1-2 PL13.14SP
[TYPE B]< TUNER / NTSC >
ANT. Input ---------------------- 75 Ω Unbal., F type
< TUNER / ATSC >
< LCD PANEL >
< VIDEO >
< AUDIO >
All items are measured across 8 Ω load at speaker output terminal with L.P.F.
Description Condition Unit Nominal Limit
1. AFT Pull-In Range --- MHz ±2.3 ±2.1
2. Synchronizing Sens.TV.ch.4
CA.ch.31CA.ch.87
dBµVdBµVdBµV
181818
202023
Description Condition Unit Nominal Limit
1. Received Freq. Range (-28dBm) --- kHz --- ±100
2. ATSC Dynamic Range (min / max)ch.4
ch.10ch.41
dBmdBmdBm
---------
-76/0-76/0
-76/+4
Description Condition Unit Nominal Limit
1. Native Pixel Resolution HorizontalVertical
pixelspixels
19201080
------
2. Brightness (w / filter) --- cd/m2 270 ---
3. Viewing Angle HorizontalVertical
°°
-88 to 88-88 to 88
------
Description Condition Unit Nominal Limit
1. Over Scan HorizontalVertical
%%
55
5±55±5
2. Color Temperature
---xy
°K 120000.2720.278
---±3%±3%
<Measurement condition>Input signal: HDMI1 Raster (40/80IRE) 1080i@60Measurement point: Screen centerMeasuring instrument: Made of KONICA MINOLTA Luminance meter CA-310Aging time: 60min. (Retail MODE / 100IRE Raster HDMI
1080i@60)MODE setting of TV: Shipment setting / Retail MODEAmbient temperature: 25°C ±5°C
3. Resolution (composite video) HorizontalVertical
lineline
400350
------
Description Condition Unit Nominal Limit
1. Audio MAX Output (ATSC 0dBfs) Lch/Rch W 10.0/10.0 9.0/9.0
2. Audio Distortion (NTSC) 500mW: Lch/Rch % 0.5/0.5 2.0/2.0
2-1 LTVN_ISP
IMPORTANT SAFETY PRECAUTIONS
Prior to shipment from the factory, our products are strictly inspected for recognized product safety and electrical codes of the countries in which they are to be sold. However, in order to maintain such compliance, it is equally important to implement the following precautions when a set is being serviced.
Safety Precautions for LCD TV Circuit1. Before returning an instrument to the
customer, always make a safety check of the entire instrument, including, but not limited to, the following items:
a. Be sure that no built-in protective devices are defective and have been defeated during servicing. (1) Protective shields are provided on this chassis to protect both the technician and the customer. Correctly replace all missing protective shields, including any removed for servicing convenience. (2) When reinstalling the chassis and/or other assembly in the cabinet, be sure to put back in place all protective devices, including but not limited to, nonmetallic control knobs, insulating fishpapers, adjustment and compartment covers/shields, and isolation resistor/capacitor networks. Do not operate this instrument or permit it to be operated without all protective devices correctly installed and functioning. Servicers who defeat safety features or fail to perform safety checks may be liable for any resulting damage.
b. Be sure that there are no cabinet openings through which an adult or child might be able to insert their fingers and contact a hazardous voltage. Such openings include, but are not limited to, (1) spacing between the Liquid Crystal Panel and the cabinet mask, (2) excessively wide cabinet ventilation slots, and (3) an improperly fitted and/or incorrectly secured cabinet back cover.
c. Antenna Cold Check - With the instrument AC plug removed from any AC source, connect an electrical jumper across the two AC plug prongs. Place the instrument AC switch in the on position. Connect one lead of an ohmmeter to the AC plug prongs tied together and touch the other ohmmeter lead in turn to each tuner antenna input exposed terminal screw and, if applicable, to the coaxial connector. If the measured resistance is less than 1.0 megohm or greater than 5.2 megohm, an abnormality exists that must be corrected before the instrument is returned to the customer. Repeat this test with the instrument AC switch in the off position.
d. Leakage Current Hot Check - With the instrument completely reassembled, plug the AC line cord directly into a 120 V AC outlet. (Do not use an isolation transformer during this test.) Use a leakage current tester or a metering system that complies with American National Standards Institute (ANSI) C101.1 Leakage Current for Appliances and Underwriters Laboratories (UL) 1410, (50.7). With the instrument AC switch first in the on position and then in the off position, measure from a known earth ground (metal water pipe, conduit, etc.) to all exposed metal parts of the instrument (antennas, handle brackets, metal cabinet, screw heads, metallic overlays, control shafts, etc.), especially any exposed metal parts that offer an electrical return path to the chassis. Any current measured must not exceed 0.5 milli-ampere. Reverse the instrument power cord plug in the outlet and repeat the test.
ANY MEASUREMENTS NOT WITHIN THE LIMITS SPECIFIED HEREIN INDICATE A POTENTIAL SHOCK HAZARD THAT MUST BE ELIMINATED BEFORE RETURNING THE INSTRUMENT TO THE CUSTOMER OR BEFORE CONNECTING THE ANTENNA OR ACCESSORIES.
2. Read and comply with all caution and safety-related notes on or inside the receiver cabinet, on the receiver chassis, or on the Liquid Crystal Panel.
ALSO TEST WITHPLUG REVERSEDUSING ACADAPTER PLUGAS REQUIRED
TEST ALL EXPOSEDMETAL SURFACES
READING SHOULD NOT BE ABOVE 0.5 mA
EARTHGROUND
_
DEVICELEAKAGECURRENT
TESTER
+BEINGTESTED
2-2 LTVN_ISP
3. Design Alteration Warning - Do not alter or add to the mechanical or electrical design of this TV receiver. Design alterations and additions, including, but not limited to circuit modifications and the addition of items such as auxiliary audio and/or video output connections, might alter the safety characteristics of this receiver and create a hazard to the user. Any design alterations or additions will void the manufacturer's warranty and may make you, the servicer, responsible for personal injury or property damage resulting therefrom.
4. Hot Chassis Warning -
a. Some TV receiver chassis are electrically connected directly to one conductor of the AC power cord and maybe safety-serviced without an isolation transformer only if the AC power plug is inserted so that the chassis is connected to the ground side of the AC power source. To confirm that the AC power plug is inserted correctly, with an AC voltmeter, measure between the chassis and a known earth ground. If a voltage reading in excess of 1.0 V is obtained, remove and reinsert the AC power plug in the opposite polarity and again measure the voltage potential between the chassis and a known earth ground.
b. Some TV receiver chassis normally have 85V AC(RMS) between chassis and earth ground regardless of the AC plug polarity. This chassis can be safety-serviced only with an isolation transformer inserted in the power line between the receiver and the AC power source, for both personnel and test equipment protection.
c. Some TV receiver chassis have a secondary ground system in addition to the main chassis ground. This secondary ground system is not isolated from the AC power line. The two ground systems are electrically separated by insulation material that must not be defeated or altered.
5. Observe original lead dress. Take extra care to assure correct lead dress in the following areas: a. near sharp edges, b. near thermally hot parts-be sure that leads and components do not touch thermally hot parts, c. the AC supply, d. high voltage, and, e. antenna wiring. Always inspect in all areas for pinched, out of place, or frayed wiring. Check AC power cord for damage.
6. Components, parts, and/or wiring that appear to have overheated or are otherwise damaged should be replaced with components, parts, or wiring that meet original specifications. Additionally, determine the cause of overheating and/or damage and, if necessary, take corrective action to remove any potential safety hazard.
7. Product Safety Notice - Some electrical and mechanical parts have special safety-related characteristics which are often not evident from visual inspection, nor can the protection they give necessarily be obtained by replacing them with components rated for higher voltage, wattage, etc. Parts that have special safety characteristics are identified by a # on schematics and in parts lists. Use of a substitute replacement that does not have the same safety characteristics as the recommended replacement part might create shock, fire, and/or other hazards. The product's safety is under review continuously and new instructions are issued whenever appropriate. Prior to shipment from the factory, our products are strictly inspected to confirm they comply with the recognized product safety and electrical codes of the countries in which they are to be sold. However, in order to maintain such compliance, it is equally important to implement the following precautions when a set is being serviced.
2-3 LTVN_ISP
Precautions during ServicingA. Parts identified by the # symbol are critical for
safety.Replace only with part number specified.
B. In addition to safety, other parts and assemblies are specified for conformance with regulations applying to spurious radiation. These must also be replaced only with specified replacements.Examples: RF converters, RF cables, noise blocking capacitors, and noise blocking filters, etc.
C. Use specified internal wiring. Note especially:
1) Wires covered with PVC tubing
2) Double insulated wires
3) High voltage leads
D. Use specified insulating materials for hazardous live parts. Note especially:
1) Insulation Tape
2) PVC tubing
3) Spacers
4) Insulators for transistors.
E. When replacing AC primary side components (transformers, power cord, etc.), wrap ends of wires securely about the terminals before soldering.
F. Observe that the wires do not contact heat producing parts (heat sinks, oxide metal film resistors, fusible resistors, etc.)
G. Check that replaced wires do not contact sharp edged or pointed parts.
H. When a power cord has been replaced, check that 11~13 lb (5~6 kg) of force in any direction will not loosen it.
I. Also check areas surrounding repaired locations.
J. Use care that foreign objects (screws, solder droplets, etc.) do not remain inside the set.
K. When connecting or disconnecting the internal connectors, first, disconnect the AC plug from the AC supply outlet.
L. When installing parts or assembling the cabinet parts, be sure to use the proper screws and tighten certainly.
2-4 LTVN_ISP
Safety Check after ServicingExamine the area surrounding the repaired location for damage or deterioration. Observe that screws, parts and wires have been returned to original positions. Afterwards, perform the following tests and confirm the specified values in order to verify compliance with safety standards.
1. Clearance Distance
When replacing primary circuit components, confirm specified clearance distance (d) and (d') between soldered terminals, and between terminals and surrounding metallic parts. (See Fig. 1)
Table 1: Ratings for selected area
Note: This table is unofficial and for reference only. Be sure to confirm the precise values.
2. Leakage Current Test
Confirm the specified (or lower) leakage current between B (earth ground, power cord plug prongs) and externally exposed accessible parts (RF terminals, antenna terminals, video and audio input and output terminals, microphone jacks, earphone jacks, etc.) is lower than or equal to the specified value in the table below.
Measuring Method: (Power ON)
Insert load Z between B (earth ground, power cord plug prongs) and exposed accessible parts. Use an AC voltmeter to measure across both terminals of load Z. See Fig. 2 and following table.
Table 2: Leakage current ratings for selected areas
Note: This table is unofficial and for reference only. Be sure to confirm the precise values.
AC Line Voltage Region Clearance Distance (d), (d’)
110 to 130 V U.S.A. or Canada
≥ 3.2 mm (0.126 inches)
AC Line Voltage Region Load Z Leakage Current (i) Earth Ground (B) to:
110 to 130 V U.S.A. or Canada
0.15 µF CAP. & 1.5 kΩ RES. Connected in parallel i ≤ 0.5 mA rms Exposed accessible
parts
Chassis or Secondary Conductor
Primary Circuit
Fig. 1
d' d
AC Voltmeter (High Impedance)
Exposed Accessible Part
B Earth Ground Power Cord Plug Prongs
Z
Fig. 2
3-1 TVN_SN
STANDARD NOTES FOR SERVICING
Circuit Board Indications1. The output pin of the 3 pin Regulator ICs is
indicated as shown.
2. For other ICs, pin 1 and every fifth pin are indicated as shown.
3. The 1st pin of every male connector is indicated as shown.
Pb (Lead) Free SolderPb free mark will be found on PCBs which use Pb free solder. (Refer to figure.) For PCBs with Pb free mark, be sure to use Pb free solder. For PCBs without Pb free mark, use standard solder.
How to Remove / Install Flat Pack-IC
1. Removal
With Hot-Air Flat Pack-IC Desoldering Machine:
1. Prepare the hot-air flat pack-IC desoldering machine, then apply hot air to the Flat Pack-IC (about 5 to 6 seconds). (Fig. S-1-1)
2. Remove the flat pack-IC with tweezers while applying the hot air.
3. Bottom of the flat pack-IC is fixed with glue to the CBA; when removing entire flat pack-IC, first apply soldering iron to center of the flat pack-IC and heat up. Then remove (glue will be melted). (Fig. S-1-6)
4. Release the flat pack-IC from the CBA using tweezers. (Fig. S-1-6)
CAUTION:
1. The Flat Pack-IC shape may differ by models. Use an appropriate hot-air flat pack-IC desoldering machine, whose shape matches that of the Flat Pack-IC.
2. Do not supply hot air to the chip parts around the flat pack-IC for over 6 seconds because damage to the chip parts may occur. Put masking tape around the flat pack-IC to protect other parts from damage. (Fig. S-1-2)
Top View
Out In
Bottom ViewInput
5
10
Pin 1
Pin 1
Pb free mark
Fig. S-1-1
3-2 TVN_SN
3. The flat pack-IC on the CBA is affixed with glue, so be careful not to break or damage the foil of each pin or the solder lands under the IC when removing it.
With Soldering Iron:
1. Using desoldering braid, remove the solder from all pins of the flat pack-IC. When you use solder flux which is applied to all pins of the flat pack-IC, you can remove it easily. (Fig. S-1-3)
2. Lift each lead of the flat pack-IC upward one by one, using a sharp pin or wire to which solder will not adhere (iron wire). When heating the pins, use a fine tip soldering iron or a hot air desoldering machine. (Fig. S-1-4)
3. Bottom of the flat pack-IC is fixed with glue to the CBA; when removing entire flat pack-IC, first apply soldering iron to center of the flat pack-IC and heat up. Then remove (glue will be melted). (Fig. S-1-6)
4. Release the flat pack-IC from the CBA using tweezers. (Fig. S-1-6)
Hot-airFlat Pack-ICDesolderingMachine
CBA
Flat Pack-IC
Tweezers
Masking Tape
Fig. S-1-2
Flat Pack-IC Desoldering Braid
Soldering Iron
Fig. S-1-3
Fine TipSoldering Iron
SharpPin
Fig. S-1-4
3-3 TVN_SN
With Iron Wire:
1. Using desoldering braid, remove the solder from all pins of the flat pack-IC. When you use solder flux which is applied to all pins of the flat pack-IC, you can remove it easily. (Fig. S-1-3)
2. Affix the wire to a workbench or solid mounting point, as shown in Fig. S-1-5.
3. While heating the pins using a fine tip soldering iron or hot air blower, pull up the wire as the solder melts so as to lift the IC leads from the CBA contact pads as shown in Fig. S-1-5.
4. Bottom of the flat pack-IC is fixed with glue to the CBA; when removing entire flat pack-IC, first apply soldering iron to center of the flat pack-IC and heat up. Then remove (glue will be melted). (Fig. S-1-6)
5. Release the flat pack-IC from the CBA using tweezers. (Fig. S-1-6)
Note: When using a soldering iron, care must be taken to ensure that the flat pack-IC is not being held by glue. When the flat pack-IC is removed from the CBA, handle it gently because it may be damaged if force is applied.
2. Installation1. Using desoldering braid, remove the solder from
the foil of each pin of the flat pack-IC on the CBA so you can install a replacement flat pack-IC more easily.
2. The “ I ” mark on the flat pack-IC indicates pin 1. (See Fig. S-1-7.) Be sure this mark matches the pin 1 on the PCB when positioning for installation. Then presolder the four corners of the flat pack-IC. (See Fig. S-1-8.)
3. Solder all pins of the flat pack-IC. Be sure that none of the pins have solder bridges.
To Solid Mounting Point
Soldering Iron
Iron Wire
or
Hot Air Blower
Fig. S-1-5
Fine TipSoldering IronCBA
Flat Pack-ICTweezers
Fig. S-1-6
Example :
Pin 1 of the Flat Pack-ICis indicated by a " " mark. Fig. S-1-7
Presolder
CBA
Flat Pack-IC
Fig. S-1-8
3-4 TVN_SN
Instructions for Handling Semi-conductorsElectrostatic breakdown of the semi-conductors may occur due to a potential difference caused by electrostatic charge during unpacking or repair work.
1. Ground for Human Body
Be sure to wear a grounding band (1 MΩ) that is properly grounded to remove any static electricity that may be charged on the body.
2. Ground for Workbench
Be sure to place a conductive sheet or copper plate with proper grounding (1 MΩ) on the workbench or other surface, where the semi-conductors are to be placed. Because the static electricity charge on clothing will not escape through the body grounding band, be careful to avoid contacting semi-conductors with your clothing.
<Incorrect>
CBA
Grounding Band
Conductive Sheet orCopper Plate
1MΩ
1MΩ
<Correct>
CBA
4-1 PL13.14-A_DC
CABINET DISASSEMBLY INSTRUCTIONS
Screw Torque Specification
* For reference
1. Disassembly FlowchartThis flowchart indicates the disassembly steps for the cabinet parts and the CBA in order to gain access to items to be serviced. When reassembling, follow the steps in reverse order. Bend, route and dress the cables as they were.
2. Disassembly Method
*1: TYPE A
*2: TYPE B
*3: 46PFL3608/F7 (Serial No.: DS2), 46PFL3908/F7 (Serial No.: DS2), 46PFL3908/F8 (Serial No.: XA2), 46PFL3608/F7 A (Serial No.: DS3)
Note:
(1) Order of steps in procedure. When reassembling, follow the steps in reverse order. These numbers are also used as the Identification (location) No. of parts in figures.
(2) Parts to be removed or installed.
Ref.No.
Part Number Part Name Tightening
Torque
L6 GCJP3100 SCREW F-PAN 3CHROM +P-TITE M3X10.0 5.2±0.9lb·in
L10 GCHP3120 SCREW F-PAN BLACK_NI +P-TITE M3X12.0 6.1±0.9lb·in
L23 GBJS3060 SCREW BIND 3CHROM +S-TITE M3X6.0
5.2±0.9lb·inL24 GBHS3060 SCREW BIND BLACK_NI
+S-TITE M3X6.0
L35 GBJB3080 SCREW BIND 3CHROM +B-TITE M3X8.0 5.2±0.9lb·in
L44 FPJ34080 SEMS-SW PAN 3CHROM + M4X8.0 6.9±0.9lb·in
L66 GBJS9060 SCREW BIND 3CHROM +S-TITE M2.6X6.0 4.3±0.45lb·in
SSK1 1ESA34506STAND SCREW KIT (SEMS-SW PAN BLACK_NI + M4X12.0)
(approx.8.7±0.9lb·in)*
[1] Stand HingeAssembly
[3] Rear Cover
[9] Function CBA Unit[10] Stand Bracket
[12] T-CON CBAUnit
[6] Speaker
[11] LCD Panel Assembly
[2] Stand BaseAssembly
[4] Power Supply CBA
[7] BottomCover L
[8] Bottom Cover R
[13] IR SensorCBA Unit
[14] Front Cabinet
[5] Digital MainCBA Unit
Step/Loc. No.
Part Fig. No. Removal Note
[1]Stand Hinge Assembly
D1 4(S-1), 4(S-2) ---
[2] Stand Base Assembly D1 --------------- ---
[3] Rear Cover D1 5(S-3), 6(S-4) ---
[4]Power Supply CBA
D2D5
4(S-5), CN501, CN601, CN1001 ---
[5] Digital Main CBA Unit
D2D5
4(S-6), CN3013*2, CN3101*2, CN3105*1, CN3801, CN3906*1, Jack Holder
---
[6] Speaker D3 --------------- ---
[7] Bottom Cover L D3 2(S-7), (S-8) ---
[8] Bottom Cover R D3 2(S-9), (S-10),
Function Knob *1
[9] Function CBA Unit
D3D5 CN4001 *1
[10] Stand Bracket D3 4(S-11) ---
[11] LCD Panel Assembly D3 --------------- *1
[12] T-CON CBA Unit D4
4(S-12), 2(S-13)*3, FFC Cable, T-CON Shield
*2
[13] IR Sensor CBA Unit D4 Sensor Plate *1
[14] Front Cabinet D4 11(S-14),
Decoration Plate *1
↓(1)
↓(2)
↓(3)
↓(4)
↓(5)
4-2 PL13.14-A_DC
(3) Fig. No. showing procedure of part location
(4) Identification of parts to be removed, unhooked, unlocked, released, unplugged, unclamped, or desoldered. P = Spring, L = Locking Tab, S = Screw, H = Hex Screw, CN = Connectore.g. 2(S-2) = two Screws of (S-2), 2(L-2) = two Locking Tabs of (L-2)
(5) Refer to the following “Reference Notes in the Table.”
*1Precautions concerning the LCD Panel Assembly:1. When you disassemble/re-assemble the Front
Cabinet
• Do not pull the FFC Cable and Board Cable forcefully when you re-assemble.
• Be careful not to scratch the display panel when assembling.
• The screw tightening torque must be 6.1lb·in (7kgf·cm).
• Make sure to replace the Decoration Plate to a new one when replacing the Front Cabinet.
• Be careful not to scratch the rear frame when disassembling/re-assembling or when tightening the screws.
2. When you disassemble/re-assemble the Function CBA Unit or the IR Sensor CBA Unit
• Be careful not to break the hooks. If you pull with too much force, the hooks may be damaged.
• Make sure the hooks are securely in place when assembling.
• The Function CBA Unit and Function Knob are fixed in place by the hooks. Make sure these hooks are not damaged. Make sure the Function CBA Unit and Function Knob are securely in place when re-assembling.
• The IR Sensor CBA Unit and Sensor Plate are fixed in place by the hooks. Make sure these hooks are not damaged. Make sure the IR Sensor CBA Unit and Sensor Plate are securely in place when re-assembling.
• When assembling the IR Sensor CBA Unit, make sure the Sensor Plate is properly set so that it contacts the LCD Panel Assembly.
*2Precautions concerning the T-CON CBA Unit:1. Be careful with the electrostatic discharge
when you repair/replace the T-CON CBA Unit.
• As for the ESD countermeasure purpose, make sure to wear the electrostatic protection gloves or antistatic wrist strap when you repair/replace the T-CON CBA Unit. If you can not conduct on the above countermeasure, make sure to release the electrostatic charge from your body by touching the equipped metal before you conduct on the repair.
• Do not press any components on T-CON CBA Unit with you finger. Make sure to hold the edge of the T-CON CBA Unit when you place it.
• Since it takes approximately 20 seconds for the electrical charge on CBA to be discharged, wait for 20 seconds after you unplug the AC cord before you replace the T-CON CBA Unit.
• Make sure to release the electrostatic charge from your body by touching the equipped metal especially before you detach the FFC cable.
4-3 PL13.14-A_DC
[46PFL3908/F7, 46PFL3708/F7, 46PFL3708/F8, 46PFL3908/F8]
[46PFL3608/F7, 46PFL3608/F7 A]
[3] Rear Cover
(S-3)
(S-3)
(S-2)
(S-2)
(S-1)
(S-4)
(S-4)
(S-4)
[1] Stand Hinge Assembly
[2] Stand Base Assembly
Fig. D1
4-4 PL13.14-A_DC
TYPE A
Jack Holder
TYPE B
[5] Digital Main CBA Unit
[4] Power Supply CBA
(S-6)
(S-6)
(S-6)
Jack Holder
(S-5)
(S-5)
(S-5)
(S-5)
Fig. D2
4-5 PL13.14-A_DC
[6] Speaker
[6] Speaker
[10] Stand Bracket
[7] Bottom Cover L
[8] Bottom Cover R
[9] Function CBA Unit*1
(S-11)
(S-11)
Function Knob*1
(S-7)
(S-9)
(S-10)
(S-8)
[11] LCD Panel Assembly*1
Fig. D3
*1: Make sure to read all the precautions on page 4-2 when you disassemble/re-assemble the Function CBA Unit.
4-6 PL13.14-A_DC
[13] IR Sensor CBA Unit*1
[12] T-CON CBA Unit*2
[14] Front Cabinet*1
Sensor Plate*1
Decoration Plate*1
T-CON Shield
T-CON Shield
FFC Cable
(S-12)
(S-14)
(S-14)
(S-12)
(S-12)
(S-12)
(S-13)
(S-14)
(S-14)
Hook*1
[46PFL3608/F7 (Serial No.: DS2), 46PFL3908/F7 (Serial No.: DS2), 46PFL3908/F8 (Serial No.: XA2), 46PFL3608/F7 A (Serial No.: DS3)]
[All models except 46PFL3608/F7 (Serial No.: DS2), 46PFL3908/F7 (Serial No.: DS2), 46PFL3908/F8 (Serial No.: XA2), 46PFL3608/F7 A (Serial No.: DS3)]
FFC Cable
Fig. D4
*1: Make sure to read all the precautions on page 4-2 when you disassemble/re-assemble the Front Cabinet or IR Sensor CBA Unit.
*2: Make sure to read all the precautions on page 4-2 when you repair/replace the T-CON CBA Unit.
4-7 PL13.14-A_DC
TV Cable Wiring Diagram
Power Supply CBA
Function CBA Unit
IR Sensor CBA Unit
To LCD PanelAssembly
To T-CON CBA Unit
To AC Cord
To Speaker
Digital Main CBA Unit
CN3801
CN4001
CN4051 CN4052
CN1001
CN601
CN501
CN3013
CN3906
*2
*1
CN3101
CN3105
*2
*1
CN3602
CN3601
*2
*1
Fig. D5
*1: TYPE A
*2: TYPE B
5-1 PL13.14EA
ELECTRICAL ADJUSTMENT INSTRUCTIONS
[TYPE A]General Note: “CBA” is abbreviation for “Circuit Board Assembly.”Note: Electrical adjustments are required after
replacing circuit components and certain mechanical parts. It is important to perform these adjustments only after all repairs and replacements have been completed. Also, do not attempt these adjustments unless the proper equipment is available.
Test Equipment Required1. Remote control unit
2. Color Analyzer, CA-310 (KONICA MINOLTA Luminance meter) or measuring instrument as good as CA-310.
How to set up the service mode:
Service mode:1. Turn the power on.
2. Press [0], [6], [2], [5], [9], [6] and [INFO] buttons on the remote control unit in this order. The following screen appears.
1. Purity Check ModeThis mode cycles through full-screen displays of red, green, blue, and white to check for non-active pixels.
1. Enter the service mode.
2. Each time the [7] button on the remote control unit is pressed, the display changes as follows.
3. To cancel or to exit from the Purity Check Mode, press [CH RETURN] or [PREV CH] button.
[current]File code: Total checksum:Panel-Option code:
Press "POWER" key to exit.
***-****_***_*Push "0" key**-***-***-***-***-*** ***-***-***-***-***
Flicker:Tuner: HDMI UART:Touch Sensor Ver: EDID:
*********OFF------ / -.--.--Push "0" key
MAC address:ESN:
**:**:**:**:**:*******************************
Total Watch Time: System Time:Lightsensor:
*******:****
"*" differs depending on the models.
[7] button
Note:When entering this mode, the default setting is White mode.
Purity Check Mode
[7] button
White 50% mode
Red, Green, Blue mode
V-ramp mode
Black mode
[7] button
White mode
[7] button
[7] button
White 20% mode[7] button
5-2 PL13.14EA
The White Balance Adjustment should be performed when replacing the LCD Panel, Digital Main CBA or T-CON CBA.
2. White Balance AdjustmentPurpose: To mix red and blue beams correctly for pure white.
Symptom of Misadjustment: White becomes bluish or reddish.
1. Operate the unit for more than 60 minutes.
2. Enter the service mode.
3. Press [VOLUME DOWN] button three times on the remote control unit to select “Drive setting” mode. “Drive” appears in the screen.
4. Set the color analyzer at the CHROMA mode and zero point calibration. Bring the optical receptor pointing at the center of the LCD-Panel.
Note: The optical receptor must be set perpendicularly to the LCD Panel surface.
5. Press [3] button to select the “HDB” for High Drive Blue adjustment. (“HDB” appears in the screen.)
6. Press [MENU] button. The internal Raster signal appears in the screen. (“Internal (Single)” appears in the upper right of the screen as shown below.)
7. Press [CHANNEL UP/DOWN] buttons to adjust the color temperature becomes 12000°K (x= 0.272 / y= 0.278 ± 0.005).
8. Press [1] button to select the “HDR” for High Drive Red adjustment (“HDR” appears in the screen.) and press [CHANNEL UP/DOWN] buttons to adjust the color temperature.
9. If necessary, adjust the “HDB” or “HDR” again.
10. Press [6] button to select the “MDB” for Middle Drive Blue adjustment (“MDB” appears in the screen.) and press [CHANNEL UP/DOWN] buttons to adjust the color temperature.
11. Press [4] button to select the “MDR” for Middle Drive Red adjustment (“MDR” appears in the screen.) and press [CHANNEL UP/DOWN] buttons to adjust the color temperature.
12. If necessary, adjust the “MDB” or “MDR” again.
ITEM SPECIFICATION
Color temperature x= 0.272 ± 0.005y= 0.278 ± 0.005
Input Signal Internal pattern (30/80% raster)
Measurement point Screen center
M. EQ.
CA-310 (KONICA MINOLTA Luminance meter) or measuring instrument as good as CA-310.
Aging time60min. (Retail MODE/100IRE Raster HDMI 1080i@60)
MODE setting of TV Shipment setting/Retail MODE
Ambient temperature 25°C ± 5°C
Color Analyzer
Perpendicularity
To avoid interference from ambient light, this adjustment should be performed in a dark room.
Internal (Single)
HDB 0
Internal (Single)
MDB 0
5-3 PL13.14EA
13. Press [9] button to select the “LDB” for Low Drive Blue adjustment (“LDB” appears in the screen.) and press [CHANNEL UP/DOWN] buttons to adjust the color temperature.
14. Press [7] button to select the “LDR” for Low Drive Red adjustment (“LDR” appears in the screen.) and press [CHANNEL UP/DOWN] buttons to adjust the color temperature.
15. If necessary, adjust the “LDB” or “LDR” again.
16. Press [CH RETURN] or [PREV CH] to shift to the initial screen in the service mode.If [White Balance] message with a green color is displayed on the upper right of the screen, this adjustment completes.If [White Balance] message with a red color is displayed, repeat above steps from 5. to 15. Then check the initial screen in the service mode again.If [White Balance] message with a red color is displayed, replace the LCD Panel or Digital Main CBA.
17. To cancel or to exit from the White Balance Adjustment, press [CH RETURN] or [PREV CH] button.
Internal (Single)
LDB 0
5-4 PL13.14EA
The VCOM Adjustment should be performed when replacing the T-CON CBA.
3. VCOM Adjustment
1. Set the color analyzer at the flicker adjustment mode and bring the optical receptor pointing at the center of the LCD-Panel at a distance of 1.18 inches(3cm) away from the LCD-Panel surface.Note: The optical receptor must be set perpendicularly to the LCD Panel surface.
2. Set the VCOM Jig to VCOM connector on Digital Main CBA Unit, and connect the VCOM Jig to PC with USB cable as shown below.
3. Enter the service mode.
4. Press [2] button to select the VCOM1 adjustment.
5. Press [1] button. VCOM1 pattern signal (1 X 1 flicker) appears in the screen.
6. Start the VCOM Adjustment software.To check if the connection is properly set, confirm that the I2C address displayed in the [I2C Address Setting] or [......connect] and [I2C Address] appears on the bottom left side of the VCOM Adjustment software screen.
7. Configure the following VCOM Adjustment software settings as shown below.Output Select: DACRegister Addressing Mode: SingleBank Select: Bank1
8. Adjust the VCOM Channel - VCOM setting of the VCOM Adjustment software so that the flicker value of the color analyzer is set to the lowest value available. The target flicker value is under 20[a.u].
9. Configure the following VCOM Adjustment software settings as shown below.Output Select: MTPRegister Addressing Mode: BurstBank Select: Bank1
10. Click on [Burn All Value To Registers] to save the settings.
11. To cancel or to exit from the VCOM Adjustment, press [CH RETURN] or [PREV CH] button.
ITEM SPECIFICATION
Measurement point Screen center
M. EQ.
CA-310 (KONICA MINOLTA Luminance meter) or measuring instrument as good as CA-310.PC (OS: Recommended for Windows XP, Vista (32-bit) or 7)VCOM JigVCOM Adjustment SoftwareUSB Cable (Type AB)
Target flicker value under 20[a.u]
Color Analyzer
Perpendicularity
To avoid interference from ambient light, this adjustment should be performed in a dark room.
Digital Main CBA Unit
4-pin connector
VCOM Jig USB Port
USB cable Type AB(To USB Port)
PC
Connect to 4-pin connector of Digital Main CBA Unit
5-5 PL13.14BEA
[TYPE B]General Note: “CBA” is abbreviation for “Circuit Board Assembly.”Note: Electrical adjustments are required after
replacing circuit components and certain mechanical parts. It is important to perform these adjustments only after all repairs and replacements have been completed. Also, do not attempt these adjustments unless the proper equipment is available.
Test Equipment Required1. Remote control unit
2. Color Analyzer, CA-310 (KONICA MINOLTA Luminance meter) or measuring instrument as good as CA-310.
How to set up the service mode:
Service mode:1. Turn the power on.
2. Press [MENU] button to display Setup menu.
3. Select “Features”.
4. Select “Software Upgrade”.
5. Select “Current Software Info”.
6. Press [0], [6], [2], [5], [9], [6] and [INFO] buttons on the remote control unit in this order. The following screen appears.
1. Purity Check ModeThis mode cycles through full-screen displays of red, green, blue, and white to check for non-active pixels.
1. Enter the service mode.
2. Each time the [7] button on the remote control unit is pressed, the display changes as follows.
3. To cancel or to exit from the Purity Check Mode, press [CH RETURN] or [PREV CH] button.
Code: Pic code:Panel-Option code:MIPS:
Press "POWER" key to exit.
*******-**-**-****-****-***-**-*****-*****-***-***-***-*****
Safety:HDMI EDID: HDMI UART:Touch Sensor Ver:
Safety_Non**OFF-.-- / ---
Total Watch Time: Lightsensor:
*******
"*" differs depending on the models.
[7] button
Note:When entering this mode, the default setting is White mode.
Purity Check Mode
[7] button
White 50% mode
Red, Green, Blue mode
V-ramp mode
Black mode
[7] button
White mode
[7] button
[7] button
White 20% mode[7] button
5-6 PL13.14BEA
The White Balance Adjustment should be performed when replacing the LCD Panel, Digital Main CBA or T-CON CBA.
2. White Balance AdjustmentPurpose: To mix red and blue beams correctly for pure white.
Symptom of Misadjustment: White becomes bluish or reddish.
1. Operate the unit for more than 60 minutes.
2. Enter the service mode.
3. Press [VOLUME DOWN] button three times on the remote control unit to select “Drive setting” mode. “Drive” appears in the screen.
4. Set the color analyzer at the CHROMA mode and zero point calibration. Bring the optical receptor pointing at the center of the LCD-Panel.
Note: The optical receptor must be set perpendicularly to the LCD Panel surface.
5. Press [3] button to select the “HDB” for High Drive Blue adjustment. (“HDB” appears in the screen.)
6. Press [MENU] button. The internal Raster signal appears in the screen. (“Internal (Single)” appears in the upper right of the screen as shown below.)
7. Press [CHANNEL UP/DOWN] buttons to adjust the color temperature becomes 12000°K (x= 0.272 / y= 0.278 ± 0.003).
8. Press [1] button to select the “HDR” for High Drive Red adjustment (“HDR” appears in the screen.) and press [CHANNEL UP/DOWN] buttons to adjust the color temperature.
9. If necessary, adjust the “HDB” or “HDR” again.
10. Press [6] button to select the “LDB” for Low Drive Blue adjustment (“LDB” appears in the screen.) and press [CHANNEL UP/DOWN] buttons to adjust the color temperature.
11. Press [4] button to select the “LDR” for Low Drive Red adjustment (“LDR” appears in the screen.) and press [CHANNEL UP/DOWN] buttons to adjust the color temperature.
12. If necessary, adjust the “LDB” or “LDR” again.
13. Press [VOLUME DOWN] button to shift to the “Debugging Message” mode. If there is no message under “[WB]” section, this adjustment completes. If “Drive settings are NG. Retry again.” is displayed, repeat above steps from 5. to 12. Then check “Debugging Message” again. If “Drive settings are NG. Retry again.” is displayed, replace the LCD Panel or Digital Main CBA.
14. To cancel or to exit from the White Balance Adjustment, press [CH RETURN] or [PREV CH] button.
ITEM SPECIFICATION
Color temperature x= 0.272 ± 0.003y= 0.278 ± 0.003
Input Signal Internal pattern (40/80% raster)
Measurement point Screen center
M. EQ.
CA-310 (KONICA MINOLTA Luminance meter) or measuring instrument as good as CA-310.
Aging time60min. (Retail MODE/100IRE Raster HDMI 1080i@60)
MODE setting of TV Shipment setting/Retail MODE
Ambient temperature 25°C ± 5°C
Color Analyzer
Perpendicularity
To avoid interference from ambient light, this adjustment should be performed in a dark room.
Internal (Single)
HDB 0
Internal (Single)
LDB 0
5-7 PL13.14BEA
The VCOM Adjustment should be performed when replacing the T-CON CBA.
3. VCOM Adjustment
1. Set the color analyzer at the flicker adjustment mode and bring the optical receptor pointing at the center of the LCD-Panel at a distance of 1.18 inches(3cm) away from the LCD-Panel surface.Note: The optical receptor must be set perpendicularly to the LCD Panel surface.
2. Set the VCOM Jig to VCOM connector on Digital Main CBA Unit, and connect the VCOM Jig to PC with USB cable as shown below.
3. Enter the service mode.
4. Press [2] button to select the VCOM1 adjustment.
5. Press [1] button. VCOM1 pattern signal (1 X 1 flicker) appears in the screen.
6. Start the VCOM Adjustment software.To check if the connection is properly set, confirm that the I2C address displayed in the [I2C Address Setting] or [......connect] and [I2C Address] appears on the bottom left side of the VCOM Adjustment software screen.
7. Configure the following VCOM Adjustment software settings as shown below.Output Select: DACRegister Addressing Mode: SingleBank Select: Bank1
8. Adjust the VCOM Channel - VCOM setting of the VCOM Adjustment software so that the flicker value of the color analyzer is set to the lowest value available. The target flicker value is under 20[a.u].
9. Configure the following VCOM Adjustment software settings as shown below.Output Select: MTPRegister Addressing Mode: BurstBank Select: Bank1
10. Click on [Burn All Value To Registers] to save the settings.
11. To cancel or to exit from the VCOM Adjustment, press [CH RETURN] or [PREV CH] button.
ITEM SPECIFICATION
Measurement point Screen center
M. EQ.
CA-310 (KONICA MINOLTA Luminance meter) or measuring instrument as good as CA-310.PC (OS: Recommended for Windows XP, Vista (32-bit) or 7)VCOM JigVCOM Adjustment SoftwareUSB Cable (Type AB)
Target flicker value under 20[a.u]
Color Analyzer
Perpendicularity
To avoid interference from ambient light, this adjustment should be performed in a dark room.
Digital Main CBA Unit
4-pin connector
VCOM Jig USB Port
USB cable Type AB(To USB Port)
PC
Connect to 4-pin connector of Digital Main CBA Unit
6-1 PL13.14INT
HOW TO INITIALIZE THE LCD TV
The purpose of initialization is to place the set in a new out of box condition. The customer will be prompted to select a language and program channels after the set has been initialized.To put the program back at the factory-default, initialize the LCD TV using the following procedure.
NOTE: Disconnect any device from the USB Port before you conduct on this procedure.
[TYPE A]1. Turn the power on.
2. Enter the service mode.
- To cancel the service mode, press [ ] button on the remote control unit.
3. Press [BACK] button to enter the Control Panel Key Confirmation Menu.
4. Press any button on the control panel.
5. Press [INFO] button to proceed with the self check mode.
6. Make sure to confirm the "INITIALIZED : OK" appear in the green screen.
7. Unplug the AC Cord and plug it back on again.
[TYPE B]1. Turn the power on.
2. Enter the service mode.
- To cancel the service mode, press [ ] button on the remote control unit.
3. Press [BACK] button to enter the Control Panel Key Confirmation Menu.
4. Press any button on the control panel.
5. Press [INFO] button to proceed with the self check mode.
6. Make sure to confirm the "INITIALIZED FINISH" appears in the green screen.
7. Unplug the AC Cord and plug it back on again.
7-1 PL13.14FW
FIRMWARE RENEWAL MODE
[TYPE A]
Equipment Required1. USB storage device
2. Remote Control Unit
Firmware Update Procedure1. Turn the power off and unplug the AC Cord.2. Insert the USB storage device to the USB port as
shown below.
3. Plug the AC Cord and turn the power on.
4. After few seconds, the menu mode will appear in the screen.
Note:After 30 seconds without an operation, the menu mode will disappear automatically.To display the menu mode again, press the [MENU] button on the remote control unit.
5. Select “Setup” and press the [OK] button to display the setup menu.
6. Select “Software”.
7. Select “Software update”.
8. Select “USB”.
9. Press the [OK] button on the remote control unit to enter the update mode. Update file selection
screen appears as follows. (Files included in the USB storage device are displayed.)
Note: To cancel the update mode, select “Cancel” and press the [OK] button.
10. Select the file and press [OK] button.
11. The update will start and the following will appear in the screen.
Note:
If the above screen isn’t displayed, repeat from step 1.
12. Select “Yes” and press the [OK] button to update.
Note:
Do not remove the USB storage device or turn the TV off while update is in progress.
13. When the firmware update is completed, the following will appear in the screen.
Remove the USB storage device from the USB port. Turn the power off and turn the power on again.
Rear Cabinet
USB port
USB storage device
Select an upgrade file
Cancel
*****_******.upg
*****_******.upg
*****_******.upg
"*" differs depending on the models.
1 2 3
Are you sure you want to update?
No Yes
Current Version: ***-****-***-* New Version: ***-****-***-*
"*" differs depending on the models.
Update your TV with new software: Done
Software update is successful.Please remove the USB storage device
and restart the TV set.
7-2 FL13.14BFW
[TYPE B]Equipment Requireda. USB storage deviceb. Remote Control Unit
Firmware Update ProcedureUser Upgrade (Filename example: TVNB1012_00_PG_XX91_BA0.bin)Upgrade the firmware only. The setting values will not be initialized. The User Upgrade and the Firmware Upgrade (Factory Upgrade) will be done by the same file. If you want to upgrade the firmware and initialize the setting values also, add “FACT_” at the beginning of the filename. If you want to upgrade the firmware only and leave the setting values as they are, eliminate the “FACT_” from the filename.
Update procedure1. Turn the power on.2. Press [MENU] button to display Menu.3. Select “Features”.4. Select “Software Upgrade”.5. Select “Upgrade” to display Upgrade screen.6. Press [OK] button to display Software Upgrade
screen.7. Select “USB” and press [OK] button.8. Insert the USB storage device to the USB port as
shown below.
9. Select “Check” and press [OK] button.10. Select “Upgrade” and press [OK] button to start
software upgrade.
11. The update will start and the following will appear in the screen.
Note: If the above screen isn’t displayed, repeat from step 1.
The appearance shown in *1 is described as follows.
12. When the firmware update is completed, the following will appear in the screen.
Remove the USB storage device from the USB port. Turn the power off and turn the power on again.
USB port
USB storage device
Rear Cabinet
Appearance State
Downloading... Downloading the firmware from the USB storage device.
Writing... Writing the downloaded firmware in flash memory.
Checking... Checking the new firmware.
Software upgrade in progress. Please wait.Do not remove the USB storage device or turn the TV off while upgrade is in progress.
Software Upgrade
Downloading...
Current Version:New Version:
*******-***-*-***-***********-***-*-***-****
0%*1
"*" differs depending on the models.
Software Upgrade
The software upgrade is completed.Remove USB storage device, turn TV off then on again.
7-3 FL13.14BFW
Factory Upgrade (Firmware Upgrade/Flash Upgrade)
Firmware Upgrade (Filename example: FACT_TVNB1012_00_PG_XX91_BA0.bin)Upgrade the firmware and initialize the setting values.The User Upgrade and the Firmware Upgrade (Factory Upgrade) will be done by the same file. If you want to upgrade the firmware and initialize the setting values also, add “FACT_” at the beginning of the filename. If you want to upgrade the firmware only and leave the setting values as they are, eliminate the “FACT_” from the filename.
Flash Upgrade (Filename example: ALL_TVNB1012_00_PG_XX91_BA0.bin)Upgrade the firmware and initialize the setting values along with the factory default such as White Balance, etc.Before the upgrade, you will need to make a note of all the factory default so you will be able to set it back on the TV after the initialization.The Flash Upgrade will be done by it's unique file.The User Upgrade/Firmware Upgrade (Factory Upgrade) file cannot be used for this upgrade.
Update procedure1. Turn the power off.2. Insert the USB storage device to the USB port as
shown below.
3. Turn the power on.4. The update will start and the following will appear
in the screen.
Note: If the above screen isn’t displayed, repeat from step 1.
The appearance shown in *1 is described as follows.
5. When the firmware update is completed, the following will appear in the screen.
Remove the USB storage device from the USB port. Turn the power off and turn the power on again. Service mode initial screen with a word “INITIALIZED” will appear in the screen. The color of the word “INITIALIZED” will change from red to green when initialization is completed.
USB port
USB storage device
Rear Cabinet
Software upgrade in progress. Please wait.Do not remove the USB storage device or turn the TV off while upgrade is in progress.
Software Upgrade
Downloading...
Current Version:New Version:
*******-***-*-***-***********-***-*-***-****
0%*1
"*" differs depending on the models.
Appearance State
Downloading... Downloading the firmware from the USB storage device.
Writing... Writing the downloaded firmware in flash memory.
Checking... Checking the new firmware.
Software Upgrade
The software upgrade is completed.Remove USB storage device, turn TV off then on again.
8-1 PL13.14ATR
TROUBLESHOOTING
Note: This Troubleshooting section covers the entire PL13.14 chassis models. Thus some Reference number of parts shown below may not be used depending on the model. Please refer to the parts list for each model.
[Power Supply Section]
When buzz sound can be heard in the periphery of power circuit.FLOW CHART NO.4
Check if there is any short-circuit on the rectifying diode and the circuit in each rectifying circuit of the secondary side. Repair it if defective. (D650, D653, D655, IC651(Q657))
The power cannot be turned on.
The fuse blows out.
FLOW CHART NO.1
FLOW CHART NO.2
Is normal state restored when once unpluggedpower cord is plugged again after several seconds?
Check if there is any leak or short-circuit on theprimary circuit component and repair it if defective.(C625, C665, D601, D602, D603, D604, D613, D617, D618, D621, D623, D664, IC601, IC604, Q601, Q602, Q603, T601, R630, R631)
Yes
No
Yes
Is the fuse (F602) normal? See FLOW CHART No.2 <The fuse blows out.>
No
Yes
Is the P-ON+21V line voltage normal?No
Check each rectifying circuit of the secondarycircuit and repair it if defective.
Check if there is any leak or short-circuit on theprimary circuit component and repair it if defective.
Check if there is any leak or short-circuit on theeach rectifying circuit component of secondary side and repair it if defective.
Make sure to repair the primary circuit component before replacing the fuse(F602).
When the output voltage fluctuates.FLOW CHART NO.3
Does the photocoupler circuit on the secondary side operate normally?
No
Yes
Check IC602, D660 and their periphery circuit. Repair it if defective.
Check D609, D613, D614, D615, D617, D619, D620, D621, Q601, Q602, IC602 and their periphery circuit. Repair it if defective.
8-2 PL13.14ATR
AL+3.3V is not output.
Yes
Replace IC651.
No
AL+3.3V is not output.
Replace IC651.
No
Yes
Yes
No
[TYPE A]FLOW CHART NO.7
Check if there is any leak or short-circuit on the loadcircuit. Repair it if defective.
AMP+13V is not output.FLOW CHART NO.6
Is approximately +13V voltage supplied to the cathode of D653(D655)?
Is approximately +13V voltage supplied to Pin(3) of IC651?
No
Yes
Check C654, C655, D653, D654, D655 and their periphery circuit. Repair it if defective.
Check C654, C655, D653, D654, D655, R676, R678, R679, R683, R684 and their periphery circuit. Repair it if defective.
[TYPE B]
Check C654, C655, D653, D654, D655, R676, R678, R679, R683, R684, R688, R689 and their periphery circuit. Repair it if defective.
Is approximately +10V voltage supplied to the emitter of Q657 and Pin(3) of IC651?
Is approximately +3.3V voltage supplied to the collector of Q657?
Replace Q657.
Check if there is any leak or short-circuit on the loadcircuit. Repair it if defective.
P-ON+21V is not output.
Is approximately +21V voltage supplied to thecathode of D650?
No
Yes
Check C651, C652, D650 and their periphery circuit. Repair it if defective.
FLOW CHART NO.5
8-3 PL13.14ATR
[Video Signal Section]
NoIs the "L" pulse supplied to Pin(5) of CN4052?
Yes
Is approximately +3.3V voltage supplied to Pin(3) terminal of the remote control receiver (RS4051)?
No
FLOW CHART NO.2
Check AL+3.3V line and repair it if defective.
Yes
Replace the Digital Main CBA Unit.
When touching each buttons, does the Pin(2) voltage of CN4001 decrease?
The key operation is not functioning.FLOW CHART NO.1
Yes
Replace the Digital Main CBA Unit.
Replace the Function CBA Unit.
Replace the IR Sensor CBA Unit.
No
No operation is possible from the remote control unit. (Operation is possible from the unit.)
Picture does not appear normally.FLOW CHART NO.3
Is approximately +3.3V voltage supplied to Pin(8) of CN501?
Digital Main CBA Unit or LCD Panel Assembly may be defective. Check and replace these parts.
No
Yes
Is approximately +21V voltage supplied to Pin(20, 21, 22, 23) of CN501?
See FLOW CHART NO.5 <P-ON+21V is not output.[Power Supply Section]>
See FLOW CHART NO.7 <AL+3.3V is not output.[Power Supply Section]>
No
Yes
8-4 PL13.14ATR
[Audio Signal Section]
SP3801, SP3802 or CL3801 may be defective. Check and replace these parts.
Audio is not output normally.FLOW CHART NO.1
Are the audio signals output to Pin(1, 2, 3, 4) of CN3801? Replace the Digital Main CBA Unit.No
Yes
Is approximately +13V voltage supplied to Pin(15, 16, 17, 18) of CN501?
Is approximately +3.3V voltage supplied to Pin(8) of CN501?
No
No
Yes
See FLOW CHART NO.7 <AL+3.3V is not output.[Power Supply Section]>
See FLOW CHART NO.6 <AMP+13V is not output. [Power Supply Section]>
Yes
9-1
IC31
01(M
AIN
MIC
RO
CO
NT
RO
LLE
R)
DIG
ITA
L M
AIN
CB
A U
NIT
AX
OA
XI
X31
0125
MH
zO
SC
TO V
IDE
O/A
UD
IOB
LOC
K D
IAG
RA
MLC
D-P
-ON
LCD
-P-O
NC
OM
P-D
ET
HP
-DE
T
CO
MP
-DE
T
VG
A-S
CL
VG
A-S
CL
VG
A-S
DA
VG
A-S
DA
AD
6A
E6
M24
N22
AC7
AC8
AE
4
AA16
Y7
W2
H6
HP
-DE
TL2AD
3
AD
4
CN
3704
CN
3706
US
B0(
-)
TX
(-)
US
B0(
+)
US
B0(
-)U
SB
0(+
)
TX
(+)
RX
(-)
RX
(+)
TX
(-)
TX
(+)
RX
(-)
RX
(+)
ET
HE
RN
ET
JAC
K
US
B J
AC
K
L23
M22
CN
3701
US
B1(
-)U
SB
1(+
)
US
B1(
-)U
SB
1(+
)W
IRE
LES
SLA
N M
OD
ULE
TO
LED
BA
CK
LIG
HT
DR
IVE
BLO
CK
DIA
GR
AM
TO
PO
WE
R S
UP
PLY
B
LOC
K D
IAG
RA
MR
ES
ET
P-O
N-H
2C
N36
01
CN
3601
PR
OT
EC
T3
BA
CK
LIG
HT-
SW
BA
CK
LIG
HT-
AD
J
PO
WE
R S
UP
PLY
CB
A
CN
501
CN
501
PR
OT
EC
T3
P-O
N-H
2S
TB
-RE
SE
T
KE
Y-IN
1
BA
CK
LIG
HT-
SW
LED
1R
EM
OT
E
BA
CK
LIG
HT-
AD
J
ST
M-S
CL
ST
M-S
DA
SC
LS
DA
6 5
(ME
MO
RY
)
Y2
T2
W3
P7
AD
5Y
15T
U-S
CL
TU
-SD
AS
CL
SD
A4 3
TU
3001
(TU
NE
R U
NIT
)P
-ON
-H2
66
KE
Y-IN
14
6
CN
3105
RE
MO
TE
55
LED
16
4
RE
SE
T4
4
PR
OT
EC
T3
33
BAC
KLI
GH
T-S
W5
5B
ACK
LIG
HT-
AD
J7
7
Q31
01LE
D D
RIV
E
RE
SE
TIC
3601
IC31
03
U3
U1
T3
V3
AC
2A
C1
LIG
HT
LIG
HT
73
Q31
02B
UF
FE
RC
N40
51K
EY
SW
ITC
H
IR S
EN
SO
R C
BA
UN
IT
FU
NC
TIO
N C
BA
UN
IT
RE
MO
TE
SE
NS
OR
RS
4051
P-O
N+
5V
CN
4001
D40
51P
OW
ER
KE
Y-IN
12
2
CN
4052
LIG
HT
SE
NS
OR
IC40
51
BLOCK DIAGRAMS
PL13.14ABLS
1. System Control Block Diagram[TYPE A]
9-2
2. Video/Audio Block Diagram
PL13.14ABLVA
DIG
ITA
L M
AIN
CB
A U
NIT
IC38
03 (
AU
DIO
AM
P)
Q38
21
Q38
22
P-O
N+
3.3V
LCD
-P-O
NC
OM
P-D
ET
TO S
YS
TE
M C
ON
TR
OL
BLO
CK
DIA
GR
AM
SP
3802
S
PE
AK
ER
R-C
H
CN
3801
SP
3801
S
PE
AK
ER
L-C
H
AM
P(L
)-O
UT
AM
P(R
)-O
UT
3S
P(R
)-4
SP
(R)+
2S
P(L
)-1
SP
(L)+
DIF
-OU
T1
DIF
-OU
T2
IF-A
GC
TO D
IGIT
AL
SIG
NA
L P
RO
CE
SS
BLO
CK
DIA
GR
AM
JK37
13P
C-R
GB
-IN
1 2 3 13 14 15 12
VG
A-R
-IN
VG
A-G
-IN
VG
A-B
-IN
VG
A-H
SY
NC
VG
A-V
SY
NC
VG
A-S
CL
VG
A-S
DA
TU
3001
DIF
-OU
T1
6D
IF-O
UT
27
(TU
NE
R U
NIT
)
IF-A
GC
5
VID
EO
SIG
NA
LA
UD
IO S
IGN
AL
1 2325 23
CO
NT
RO
L LO
GIC
DR
IVE
DR
IVE
PW
MLO
GIC
18 20
DR
IVE
DR
IVE
PW
MLO
GIC
12P
OW
ER
LIM
IT
PO
WE
RLI
MIT
AU
DIO
(L)-
IN
AU
DIO
(R)-
IN
JK37
06
DIG
ITA
LA
UD
IO-O
UT
(CO
AX
IAL)
Q37
09B
UF
FE
R
AU
DIO
(L)-
INA
UD
IO(R
)-IN
HP
(R)
HP
(L)
SP
DIF
CO
MP
ON
EN
T-Y
/VID
EO
-IN
CO
MP
ON
EN
T-P
b-IN
CO
MP
ON
EN
T-P
r-IN
JK37
01C
OM
-VID
EO
-Y/V
IDE
O-I
N
CO
M-V
IDE
O-P
r-IN
CO
M-V
IDE
O-P
b-IN
HP
-DE
T
JK38
01H
EA
DP
HO
NE
JAC
K
9-3 PL13.14ABLD
[46P
FL
3608
/F7
(Ser
ial N
o.:
DS
2),
46P
FL
3908
/F7
(Ser
ial N
o.:
DS
2),
46P
FL
3908
/F8
(Ser
ial N
o.:
XA
2),
46P
FL
3608
/F7
A (
Ser
ial N
o.:
DS
3)]
DIG
ITA
L M
AIN
CB
A U
NIT
IC31
01 (
DIG
ITA
L S
IGN
AL
PR
OC
ES
S)
CN
3906
DIG
ITA
LS
IGN
AL
PR
OC
ES
SH
DM
I-IN
1
HD
MI-
IN2
JK37
17 DAT
A0(
+)
AR
CA
RC
-OU
T
DAT
A0(
-)D
ATA
1(+
)D
ATA
1(-)
DAT
A2(
+)
DAT
A2(
-)
HD
MI-
DAT
AH
DM
I-C
LOC
K
714 9 4 6 1 3 10 12 16 15 7 9 4 6 1 3 10 12 16 15
JK37
15CLO
CK
(+)
CLO
CK
(-)
DAT
A(0
-15)
AD
DE
SS
(0-1
4)
DAT
A(1
6-31
)
AD
DE
SS
(0-1
4)
AU
DIO
DE
CO
DE
R
HD
MI
I/F
HD
MI S
W
TO V
IDE
O/A
UD
IOB
LOC
K D
IAG
RA
M
VID
EO
DE
CO
DE
R
VID
EO
SIG
NA
LA
UD
IO S
IGN
AL
DAT
A(0
-7)
IC31
02(N
AN
D F
LAS
H M
EM
OR
Y)
IC34
01(D
DR
3 S
DR
AM
)M
MD
Q(0
-31)
MM
A(0
-14)
MM
CD
AT(0
-7)
IC34
02
(DD
R3
SD
RA
M)
A/D
CO
NV
ER
TER
SW
VG
A-R
-IN
VG
A-G
-IN
VG
A-B
-IN
CO
M-V
IDE
O-Y
/VID
EO
-IN
CO
M-V
IDE
O-P
b-IN
CO
M-V
IDE
O-P
r-IN
DE
MO
DU
LATO
R/M
PE
G D
EC
OD
ER
AU
DIO
I/F
DIF
-OU
T1
DIF
-OU
T2
IF-A
GC
IF-A
GC
VG
A-H
SY
NC
VG
A-V
SY
NC
VG
A-H
SY
NC
VG
A-V
SY
NC
LVD
S
TX
AM
P(L
)-O
UT
AM
P(R
)-O
UT
SP
DIF
AU
DIO
(L)-
INA
UD
IO(R
)-IN
HP
(L)
HP
(R)
DAT
A0(
+)
DAT
A0(
-)D
ATA
1(+
)D
ATA
1(-)
DAT
A2(
+)
DAT
A2(
-)
HD
MI-
DAT
AH
DM
I-C
LOC
K
CLO
CK
(+)
CLO
CK
(-)
Y11
AA12
AD13
AB13
AC13
AB10
AC11
AD11
AB11
AB17
AC18
AE14
AC14
AD17
AC17
F4
F5
AC23
AE22
AD23
AE23
AD24
AE24
AD22
AC22
W6
T7
W23
W22
V23
V22
U23
V24
Y25
Y24
AA
5V
7
AE
9A
D9
AA13
HD
MI-
IN3
7 9 4 6 1 3 10 12 16 15
JK37
16 DAT
A0(
+)
DAT
A0(
-)D
ATA
1(+
)D
ATA
1(-)
DAT
A2(
+)
DAT
A2(
-)
HD
MI-
DAT
AH
DM
I-C
LOC
K
CLO
CK
(+)
CLO
CK
(-)
AB24
AC25
AA23
AB25
Y23
AA24
AC24
AD25
AE
3R
9
L4 K3
K4
J3 H2
M6
M5
N5
M4
L6 L5 K5
J5 M7
L7H3
H4
J1 J2L324 23 22 21 20 19 17 1614 13
LVD
S-O
D0(
-)LV
DS
-OD
0(+
)LV
DS
-OD
1(-)
LVD
S-O
D1(
+)
LVD
S-O
D2(
-)LV
DS
-OD
2(+
)
LVD
S-O
CLK
(-)
LVD
S-O
CLK
(+)
LVD
S-O
D3(
-)LV
DS
-OD
3(+
)
T-C
ON
C
BA
UN
IT
CN
_L(6
8PIN
)
LC
D P
AN
EL
AS
SE
MB
LY LC
D
MO
DU
LE
CN
_R(6
8PIN
)
40 39 38 37 36 35 30 29 33 32
LVD
S-E
D0(
-)LV
DS
-ED
0(+
)LV
DS
-ED
1(-)
LVD
S-E
D1(
+)
LVD
S-E
D2(
-)LV
DS
-ED
2(+
)
LVD
S-E
CLK
(-)
LVD
S-E
CLK
(+)
LVD
S-E
D3(
-)LV
DS
-ED
3(+
)
G3
12LV
DS
-OD
4(-)
F3
11LV
DS
-OD
4(+
)K
528
LVD
S-E
D4(
-)J6
27LV
DS
-ED
4(+
)
3. Digital Signal Process Block Diagram
9-4
4. LED Backlight Drive Block Diagram
IC11
01
(LE
D B
AC
KLI
GH
T D
RIV
ER
)
OV
P
DR
IVE
Q11
01
CO
NTR
OL
LOG
IC
1
13 5 6 7
12
DR
IVE
VR
EG
FAIL
DE
TE
CT
1117 15
VLE
D1
1IL
ED
12
Q11
02
PO
WE
R S
UP
PLY
CB
A
LC
D P
AN
EL
A
SS
EM
BLY
PR
OT
EC
T3
BA
CK
LIG
HT-
AD
JB
AC
KLI
GH
T-S
WT
O
SY
ST
EM
CO
NT
RO
LB
LOC
K D
IAG
RA
M
VIN
IC12
01
(LE
D B
AC
KLI
GH
T D
RIV
ER
)
OV
PC
N10
01
DR
IVE
Q12
01
CO
NTR
OL
LOG
IC
1
13 5 6 7
12
DR
IVE
VR
EG
FAIL
DE
TE
CT
1117 15
VLE
D2
3IL
ED
24
Q12
02
IC13
01
(LE
D B
AC
KLI
GH
T D
RIV
ER
)
OV
P
DR
IVE
Q13
01
CO
NTR
OL
LOG
IC
1
13 5 6 7
12
DR
IVE
VR
EG
FAIL
DE
TE
CT
1117 15
VLE
D3
5IL
ED
36
Q13
02
PL13.14BLBD
9-5
5. Power Supply Block Diagram
HO
TC
OL
D
HO
T C
IRC
UIT
. BE
CA
RE
FU
L.
CN
601
B W
AC
601
AC
CO
RD
LIN
EF
ILT
ER
L602
A
LIN
EF
ILT
ER
L601
AT
601
BR
IDG
ER
EC
TIF
IER
T16
02
TO S
YS
TE
M C
ON
TR
OL
BLO
CK
DIA
GR
AM
PO
WE
R S
UP
PLY
CB
A
DIG
ITA
L M
AIN
CB
A U
NIT
F60
2 2.
5A/2
50V
1 3 5 6 7
1415 13 12 11 10
2
2 43
1 4
8 5
T17
01
14 1315 11 10
6 7
IC60
2
14 3
2
Q16
02S
WIT
CH
ING
Q16
01
VC
CS
WIT
CH
ING
IC16
01(S
WIT
CH
ING
CO
NT
RO
L)
SW
ITC
HIN
G
CO
NT
RO
L
7
11
116
12
14
T16
01
1 4
8 58
IC16
02(I
SO
LAT
OR
)
Q69
1
Q16
08
Q16
07
Q16
04
14 3
2
IC17
02
14 3
2
CN
3601
P-O
N+
21V
20-2
3
AL+
3.3V
88
15-1
820
-23
CN
501
AM
P+
13V
15-1
8
Q65
3
Q70
1
Q70
2
P-O
N-H
2
RE
SE
T
RE
SE
TQ
654
RE
SE
TQ
650
D60
1-D
604
AL+
3.3V
P-O
N+
21V
AM
P+
13V
AM
P+
13V
VIN
2.5A
250
V
FB
Q60
1S
WIT
CH
ING
Q60
2S
WIT
CH
ING
IC65
1+
3.3V
RE
G.
SW
ITC
HIN
G
CO
NT
RO
L
IC60
1
2
IS3
OU
T5
VC
C6
ZC
D1
FBQ
1704
SW
ITC
HIN
GQ
1702
Q17
01
SW
+15
V
SW
ITC
HIN
G
CO
NT
RO
L
IC17
01
2
IS3
OU
T5
VC
C6
ZC
D1
ER
RO
R
VO
LTA
GE
DE
T
ER
RO
R
VO
LTA
GE
DE
T
CA
UT
ION
!F
ixed
vol
tage
(or
Aut
o vo
ltage
sel
ecta
ble)
pow
er s
uppl
y ci
rcui
t is
used
in th
is u
nit.
If M
ain
Fus
e (F
602)
is b
low
n , c
heck
to s
ee th
at a
ll co
mpo
nent
s in
the
pow
er s
uppl
y ci
rcui
t are
not
def
ectiv
e be
fore
you
con
nect
the
AC
plu
g to
the
AC
pow
er s
uppl
y.
Oth
erw
ise
it m
ay c
ause
som
e co
mpo
nent
s in
the
pow
er s
uppl
y ci
rcui
t to
fail.
For
con
tinue
d pr
otec
tion
agai
nst r
isk
of fi
re,
repl
ace
only
with
sam
e ty
pe 2
.5A
, 250
V fu
se.
CA
UT
ION
! :
AT
TE
NT
ION
: U
tilis
er u
n fu
sibl
e de
rec
hang
e de
mêm
e ty
pe d
e 2.
5A, 2
50V
.2.
5A 2
50V
NO
TE
:T
he v
olta
ge fo
r pa
rts
in h
ot c
ircui
t is
mea
sure
d us
ing
hot G
ND
as
a co
mm
on te
rmin
al.
PL13.14ABLP
9-6
[TYPE B]
IC30
01(M
AIN
MIC
RO
CO
NT
RO
LLE
R)
DIG
ITA
L M
AIN
CB
A U
NIT
XO
UT
XIN
X31
0124
MH
zO
SC
TO V
IDE
O/A
UD
IOB
LOC
K D
IAG
RA
MA
MP
-MU
TE
AM
P-M
UT
EC
OM
P-D
ET
CO
MP
-DE
T
VG
A-S
CL
VG
A-S
CL
VG
A-S
DA
VG
A-S
DA
194
195
67212
127
133
213
66
CN
3009
US
B(+
)U
SB
(-)
US
B(+
)U
SB
(-)
US
B J
AC
K
TO
LED
BA
CK
LIG
HT
DR
IVE
BLO
CK
DIA
GR
AM
TO
PO
WE
R S
UP
PLY
B
LOC
K D
IAG
RA
MR
ES
ET
P-O
N-H
2C
N36
02
CN
3602
PR
OT
EC
T3
BA
CK
LIG
HT-
SW
BA
CK
LIG
HT-
AD
J
PO
WE
R S
UP
PLY
CB
A
CN
501
CN
501
PR
OT
EC
T3
P-O
N+
3.3V
AL+
3.3V
Q36
05
Q36
06
Q31
03
P-O
N-H
2
ST
B-R
ES
ET
KE
Y-IN
1
BA
CK
LIG
HT-
SW
LED
1R
EM
OT
E
BA
CK
LIG
HT-
AD
J
SP
I-S
CL
SP
I-S
DA
SC
LS
DA
6 5
(ME
MO
RY
)
206
134
75 129
216
126
125
TU
-SC
LT
U-S
DA
SC
LS
DA
4 3
TU
3901
(TU
NE
R U
NIT
)P
-ON
-H2
186
KE
Y-IN
14
6
CN
3101
RE
MO
TE
55
LED
16
4
RE
SE
T20
4
PR
OT
EC
T3
213
BAC
KLI
GH
T-S
W19
5B
ACK
LIG
HT-
AD
J17
7
Q35
01, Q
3502
LED
DR
IVE
RE
SE
TIC
3009
, Q
3104
IC30
06
215
210
208
205
199
200
LIG
HT
LIG
HT
73
Q30
10B
UF
FE
RC
N40
51K
EY
SW
ITC
H
IR S
EN
SO
R C
BA
UN
IT
FU
NC
TIO
N C
BA
UN
IT
RE
MO
TE
SE
NS
OR
RS
4051
P-O
N+
5V
CN
4001
D40
51P
OW
ER
KE
Y-IN
12
2
CN
4052
LIG
HT
SE
NS
OR
IC40
51
PL13.14BBLS
1. System Control Block Diagram
9-7
2. Video/Audio Block Diagram
PL13.14BBLVA
DIG
ITA
L M
AIN
CB
A U
NIT
IC38
01 (
AU
DIO
AM
P)
Q38
01
AM
P-M
UT
EC
OM
P-D
ET
TO S
YS
TE
M C
ON
TR
OL
BLO
CK
DIA
GR
AM
SP
3802
S
PE
AK
ER
R-C
H
CN
3801
SP
3801
S
PE
AK
ER
L-C
H
AM
P(L
)-O
UT
AM
P(R
)-O
UT
3S
P(R
)-4
SP
(R)+
2S
P(L
)-1
SP
(L)+
DIF
-OU
T1
DIF
-OU
T2
IF-A
GC
TO D
IGIT
AL
SIG
NA
L P
RO
CE
SS
BLO
CK
DIA
GR
AM
JK30
01P
C-R
GB
-IN
1 2 3 13 14 15 12
VG
A-R
-IN
VG
A-G
-IN
VG
A-B
-IN
VG
A-H
SY
NC
VG
A-V
SY
NC
VG
A-S
CL
VG
A-S
DA
TU
3901
DIF
-OU
T1
6D
IF-O
UT
27
(TU
NE
R U
NIT
)
IF-A
GC
5
VID
EO
SIG
NA
LA
UD
IO S
IGN
AL
1 2325 23
CO
NT
RO
L LO
GIC
DR
IVE
DR
IVE
PW
MLO
GIC
18 20
DR
IVE
DR
IVE
PW
MLO
GIC
12P
OW
ER
LIM
IT
PO
WE
RLI
MIT
AU
DIO
(L)-
IN
AU
DIO
(R)-
IN
JK37
01
DIG
ITA
LA
UD
IO-O
UT
(CO
AX
IAL)
Q37
01B
UF
FE
R
AU
DIO
(L)-
INA
UD
IO(R
)-IN
HP
(R)
HP
(L)
SP
DIF
CO
MP
ON
EN
T-Y
/VID
EO
-IN
CO
MP
ON
EN
T-P
b-IN
CO
MP
ON
EN
T-P
r-IN
JK37
02C
OM
-VID
EO
-Y/V
IDE
O-I
N
CO
M-V
IDE
O-P
r-IN
CO
M-V
IDE
O-P
b-IN
JK37
03H
EA
DP
HO
NE
JAC
K
9-8 PL13.14BBLD
DIG
ITA
L M
AIN
CB
A U
NIT
IC30
01 (
DIG
ITA
L S
IGN
AL
PR
OC
ES
S)
CN
3013
DIG
ITA
LS
IGN
AL
PR
OC
ES
SH
DM
I-IN
1
HD
MI-
IN2
JK30
03 DAT
A0(
+)
DAT
A0(
-)D
ATA
1(+
)D
ATA
1(-)
DAT
A2(
+)
DAT
A2(
-)
HD
MI-
DAT
AH
DM
I-C
LOC
K
7 9 4 6 1 3 10 12 16 15 7 9 4 6 1 3 10 12 16 15
JK30
02CLO
CK
(+)
CLO
CK
(-)
DAT
A(0
-15)
AD
DE
SS
(0-1
3)
AU
DIO
DE
CO
DE
R
HD
MI
I/F
HD
MI S
W
TO V
IDE
O/A
UD
IOB
LOC
K D
IAG
RA
M
VID
EO
DE
CO
DE
R
VID
EO
SIG
NA
LA
UD
IO S
IGN
AL
IC30
02(D
DR
2 S
DR
AM
)M
DQ
L(0-
7),
MD
QU
(0-7
)
MA
(0-1
3)
A/D
CO
NV
ER
TER
SW
VG
A-R
-IN
VG
A-G
-IN
VG
A-B
-IN
CO
M-V
IDE
O-Y
/VID
EO
-IN
CO
M-V
IDE
O-P
b-IN
CO
M-V
IDE
O-P
r-IN
DE
MO
DU
LATO
R/M
PE
G D
EC
OD
ER
AU
DIO
I/F
DIF
-OU
T1
DIF
-OU
T2
IF-A
GC
IF-A
GC
VG
A-H
SY
NC
VG
A-V
SY
NC
VG
A-H
SY
NC
VG
A-V
SY
NC
LVD
S
TX
AM
P(L
)-O
UT
AM
P(R
)-O
UT
SP
DIF
AU
DIO
(L)-
INA
UD
IO(R
)-IN
HP
(L)
HP
(R)
DAT
A0(
+)
DAT
A0(
-)D
ATA
1(+
)D
ATA
1(-)
DAT
A2(
+)
DAT
A2(
-)
HD
MI-
DAT
AH
DM
I-C
LOC
K
CLO
CK
(+)
CLO
CK
(-)
26 32 31 29 27 36 34 38 35 60 61 47 48 63 64 130
5 4 8 7 11 10 3 2 6 9 89 88 92 91 95 94 87 86 93 96
7170 74
HD
MI-
IN3
7 9 4 6 1 3 10 12 16 15
JK30
04 DAT
A0(
+)
DAT
A0(
-)D
ATA
1(+
)D
ATA
1(-)
DAT
A2(
+)
DAT
A2(
-)
HD
MI-
DAT
AH
DM
I-C
LOC
K
CLO
CK
(+)
CLO
CK
(-)
16 15 19 18 22 21 14 13 20 23
108
105
106
101
102
122
123
120
121
118
119
114
115
116
117
99 100
103
104
107
24 23 22 21 20 19 17 16 40 39 38 37 36 35 30 29 33 3214 13
LVD
S-O
D0(
-)LV
DS
-OD
0(+
)LV
DS
-OD
1(-)
LVD
S-O
D1(
+)
LVD
S-O
D2(
-)LV
DS
-OD
2(+
)
LVD
S-O
CLK
(-)
LVD
S-O
CLK
(+)
LVD
S-O
D3(
-)LV
DS
-OD
3(+
)
T-C
ON
C
BA
UN
IT
CN
_L(6
8PIN
)
LC
D P
AN
EL
AS
SE
MB
LY LC
D
MO
DU
LE
CN
_R(6
8PIN
)
LVD
S-E
D0(
-)LV
DS
-ED
0(+
)LV
DS
-ED
1(-)
LVD
S-E
D1(
+)
LVD
S-E
D2(
-)LV
DS
-ED
2(+
)
LVD
S-E
CLK
(-)
LVD
S-E
CLK
(+)
LVD
S-E
D3(
-)LV
DS
-ED
3(+
)
3. Digital Signal Process Block Diagram
9-9
4. LED Backlight Drive Block Diagram
IC11
01
(LE
D B
AC
KLI
GH
T D
RIV
ER
)
OV
P
DR
IVE
Q11
01
CO
NTR
OL
LOG
IC
1
13 5 6 7
12
DR
IVE
VR
EG
FAIL
DE
TE
CT
1117 15
VLE
D1
1IL
ED
12
Q11
02
PO
WE
R S
UP
PLY
CB
A
LC
D P
AN
EL
A
SS
EM
BLY
PR
OT
EC
T3
BA
CK
LIG
HT-
AD
JB
AC
KLI
GH
T-S
WT
O
SY
ST
EM
CO
NT
RO
LB
LOC
K D
IAG
RA
M
VIN
IC12
01
(LE
D B
AC
KLI
GH
T D
RIV
ER
)
OV
PC
N10
01
DR
IVE
Q12
01
CO
NTR
OL
LOG
IC
1
13 5 6 7
12
DR
IVE
VR
EG
FAIL
DE
TE
CT
1117 15
VLE
D2
3IL
ED
24
Q12
02
IC13
01
(LE
D B
AC
KLI
GH
T D
RIV
ER
)
OV
P
DR
IVE
Q13
01
CO
NTR
OL
LOG
IC
1
13 5 6 7
12
DR
IVE
VR
EG
FAIL
DE
TE
CT
1117 15
VLE
D3
5IL
ED
36
Q13
02
PL13.14BLBD
9-10
5. Power Supply Block Diagram
HO
TC
OL
D
HO
T C
IRC
UIT
. BE
CA
RE
FU
L.
CN
601
B W
AC
601
AC
CO
RD
LIN
EF
ILT
ER
L602
A
LIN
EF
ILT
ER
L601
AT
601
BR
IDG
ER
EC
TIF
IER
T16
02
TO S
YS
TE
M C
ON
TR
OL
BLO
CK
DIA
GR
AM
PO
WE
R S
UP
PLY
CB
A
DIG
ITA
L M
AIN
CB
A U
NIT
F60
2 2.
5A/2
50V
1 3 5 6 7
1415 13 12 11 10
2
2 43
1 4
8 5
T17
01
14 1315 11 10
6 7
IC60
2
14 3
2
Q16
02S
WIT
CH
ING
Q16
01
VC
CS
WIT
CH
ING
IC16
01(S
WIT
CH
ING
CO
NT
RO
L)
SW
ITC
HIN
G
CO
NT
RO
L
7
11
116
12
14
T16
01
1 4
8 58
IC16
02(I
SO
LAT
OR
)
Q69
1
Q16
08
Q16
07
Q16
04
14 3
2
IC17
02
14 3
2
CN
3602
P-O
N+
21V
20-2
3
AL+
3.3V
88
15-1
820
-23
CN
501
AM
P+
13V
15-1
8
Q65
3
Q70
1
Q70
2
P-O
N-H
2
RE
SE
T
RE
SE
TQ
654
RE
SE
TQ
650
D60
1-D
604
AL+
3.3V
P-O
N+
21V
AM
P+
13V
AM
P+
13V
VIN
2.5A
250
V
FB
Q60
1S
WIT
CH
ING
Q60
2S
WIT
CH
ING
IC65
1, Q
657
+3.
3V R
EG
.
SW
ITC
HIN
G
CO
NT
RO
L
IC60
1
2
IS3
OU
T5
VC
C6
ZC
D1
FBQ
1704
SW
ITC
HIN
GQ
1702
Q17
01
SW
+15
V
SW
ITC
HIN
G
CO
NT
RO
L
IC17
01
2
IS3
OU
T5
VC
C6
ZC
D1
ER
RO
R
VO
LTA
GE
DE
T
ER
RO
R
VO
LTA
GE
DE
T
CA
UT
ION
!F
ixed
vol
tage
(or
Aut
o vo
ltage
sel
ecta
ble)
pow
er s
uppl
y ci
rcui
t is
used
in th
is u
nit.
If M
ain
Fus
e (F
602)
is b
low
n , c
heck
to s
ee th
at a
ll co
mpo
nent
s in
the
pow
er s
uppl
y ci
rcui
t are
not
def
ectiv
e be
fore
you
con
nect
the
AC
plu
g to
the
AC
pow
er s
uppl
y.
Oth
erw
ise
it m
ay c
ause
som
e co
mpo
nent
s in
the
pow
er s
uppl
y ci
rcui
t to
fail.
For
con
tinue
d pr
otec
tion
agai
nst r
isk
of fi
re,
repl
ace
only
with
sam
e ty
pe 2
.5A
, 250
V fu
se.
CA
UT
ION
! :
AT
TE
NT
ION
: U
tilis
er u
n fu
sibl
e de
rec
hang
e de
mêm
e ty
pe d
e 2.
5A, 2
50V
.2.
5A 2
50V
NO
TE
:T
he v
olta
ge fo
r pa
rts
in h
ot c
ircui
t is
mea
sure
d us
ing
hot G
ND
as
a co
mm
on te
rmin
al.
PL13.14BBLP
10-1 PL13.14SC
SCHEMATIC DIAGRAMS / CBA AND TEST POINTS
Standard Notes
WARNING
Many electrical and mechanical parts in this chassis have special characteristics. These characteristics often pass unnoticed and the protection afforded by them cannot necessarily be obtained by using replacement components rated for higher voltage, wattage, etc. Replacement parts that have these special safety characteristics are identified in this manual and its supplements; electrical components having such features are identified by the mark “#” in the schematic diagram and the parts list. Before replacing any of these components, read the parts list in this manual carefully. The use of substitute replacement parts that do not have the same safety characteristics as specified in the parts list may create shock, fire, or other hazards.
Notes:1. Do not use the part number shown on these
drawings for ordering. The correct part number is shown in the parts list, and may be slightly different or amended since these drawings were prepared.
2. All resistance values are indicated in ohms (K = 103, M = 106).
3. Resistor wattages are 1/4W or 1/6W unless otherwise specified.
4. All capacitance values are indicated in µF (P = 10-6 µF).
5. All voltages are DC voltages unless otherwise specified.
6. This schematic diagrams are masterized version that should cover the entire PL13.14 chassis models.Thus some parts in detail illustrated on this schematic diagrams may vary depend on the model within the PL13.14 chassis.Please refer to the parts lists for each models.
7. The Circuit Board layout illustrated on this service manual is the latest version for this chassis at the moment of making this service manual. Depend on the mass production date of each model, the actual layout of each Board may differ slightly from this version.
10-2 PL13.14SC
LIST OF CAUTION, NOTES, AND SYMBOLS USED IN THE SCHEMATIC DIAGRAMS ON THE FOLLOWING PAGES:
1. CAUTION:CAUTION: FOR CONTINUED PROTECTION AGAINST RISK OF FIRE, REPLACE ONLY WITH SAME TYPE_A,_V FUSE.
ATTENTION: UTILISER UN FUSIBLE DE RECHANGE DE MÊME TYPE DE_A,_V.
2. CAUTION: Fixed Voltage (or Auto voltage selectable) power supply circuit is used in this unit. If Main Fuse (F602) is blown, first check to see that all components in the power supply circuit are not defective before you connect the AC plug to the AC power supply. Otherwise it may cause some components in the power supply circuit to fail.
3. Note:1. Do not use the part number shown on the drawings for ordering. The correct part number is shown in the
parts list, and may be slightly different or amended since the drawings were prepared.
2. To maintain original function and reliability of repaired units, use only original replacement parts which are listed with their part numbers in the parts list section of the service manual.
4. Voltage indications on the schematics are as shown below: Plug the TV power cord into a standard AC outlet.:
5. How to read converged lines
6. Test Point Information
2 315.0 5.0
Voltage Indicates that the voltage is not consistent here.
Power on mode(Unit: Volt)
1-D3
Distinction AreaLine Number (1 to 3 digits)
Examples:1. "1-D3" means that line number "1" goes to the line number "1" of the area "D3". 2. "1-B1" means that line number "1" goes to the line number "1" of the area "B1".
3
2
1
A B C D
1-B1
1-D3
AREA D3
AREA B1
: Indicates a test point with a jumper wire across a hole in the PCB.
: Used to indicate a test point with a component lead on foil side.
: Used to indicate a test point with no test pin.
: Used to indicate a test point with a test pin.
The reference number of parts on Schematic Diagrams/CBA can be retrieved by application search function.
10-3
1000P/250VC619
L602OPEN
2.5A/250VF602
D651OPEN
C651470/25V
C655470/16V
1ZB20BBD654
D655SB3150BH
3.3KR661
3.9KR657
0R666
2.7KR66022KR659
180R654
C654470/16V
180R655
KTC3875S-Y-RTK/P
Q653
B
CN601W
0.1/310V
C6041.2M/1/2W
R601VARISTORSA601 1
/310V
C614
L601OPEN
1N5406BHD601
1N5406BHD603
1N5406BHD602
1N5406BHD604
10R608
33/400VC605
1000P/2KV
C606
OPENR602
510KR626
D653SB3150BH
D660SL431A-AT
2.7KR658
0.1C660
JS601
680P/2KV
C665560KR631
560KR630
RS1KJTDD664
BEADBC602
1000PC607
820KR609
22KR606
5
6
7
81
4
3
2
IC601FA5640N
ZCD
GND OUT
VCC
NU
VH
IS
FB
150PC608
220PC610
0.22/2W
R618
1ZB36BBD613
4.7KR617
RS1GJTDD609
270R605
4.7KR607
OPENR603
RS1GJTDD621
15KR610
15KR611
15KR614
OPEND611A
1000PC612
TK3P50DQ602
4
3 2
1
IC602TLP781F
C652470/25V
C407OPEND650
SB3200BR
2200P/1KVC650
C62033/35V TFZVTR27B
D614OPENR613
0.1C611
22KR628
TFZVTR18BD618
OPENR663
10KR669
8.2KR667OPEN
R674OPENR675
1R651
KTC3875S-Y-RTK/P
Q654C6561/50V
MM5Z4V3BD657
10KR652
D656RS1GJTD
22KR653
KTC3875S-Y-RTK/P
Q702
KTC3875S-Y-RTK/P
Q701
47KR704
47KR702
OPENC701
10KR701
10KR703
AC601AC CORD
2.5A250V
L602ALINE FILTER
L601ALINE FILTER
1N5406BHD607
1N4005D605
1N4005D606
JS6020.1/310V
C602
510KR625510KR624
39KR627
2.7KR623 RS1GJTD
D619RS1GJTDD620
4
3 2
1
IC603OPEN
4.7R619
8.2KR632
8.2KR633
HSC119D617
47/50V
C615
2200PC625
WIREBC603
2.7KR604
KTC3875S-Y-RTK/P
Q60347KR620MM5Z5V6BD623
47KR629
0.1C624
IC604SL431A-AT
4700PC621
1000PC622
HSC119D615
OPENR664
OPENR665
8.2KR656
47KR662
KTC3875S-Y-RTK/P
Q650
14 GND
4 RESET
9 GND
7 BACKLIGHT-ADJ
5 BACKLIGHT-SW
19 GND
22 P-ON+21V
P-ON-H26
23 P-ON+21V
16 AMP+13V
20 P-ON+21V
15 AMP+13V
21 P-ON+21V
11 GND
2 PROTECT1
10 GND
CN5011 LED-CONT(NU)
13 GND
8 AL+3.3V
18 AMP+13V
3 PROTECT3
17 AMP+13V
12 GND
OPENC638
OPENC639
OPENC637
OPENC664C662
22/50V
3.3R685
2.7R689
Q657AOPEN
3.3R686
6.8/2WR679
3.3R687
6.8/2WR678
6.8/2WR676
2.2R688
3.9R683
3.9R684
OPENC635
OPENC631
HSC119D661
C663100/10V
1 2 3
IC651AP1117E33G-13
OUT
INGND
BACKLIGHT-SWBACKLIGHT-ADJPROTECT3AMP+13V
OPENC630
OPENC636
OPENC633
OPEND406 OPEN
D405
OPENC632
22PC1610
0.1C1611
1200PC1607
OPENC1613
1000PC1608
750KR1618
750KR1613
OPEND1604750K
R1614
47KR1616
100/400V
C1621
30PFB60D1605
OPENC1625
750KR1605
4.7/50V
C1602
1000PC1606
750KR1612
47R1625
12KR1627
750KR1615
12KR1623
750KR1604
750KR1617
120KR1606
OPENC1623
1200PC1605
OPENC1614
51KR1608
1.8KR1621
22PC1609
OPENC1622
750KR1620
750KR1602
47R1626
30PFB60D1603
18KR1610
750KR1601
13
1
15
14
16
3
6
5
11
4
7
12
10
8 9
2
IC1601UCC28063DR
OPEND1602
0.22C1603
5.6KR1609
750KR1619
18KR1622
0.022C1601
68KR1645
220R1607
2.2C1604OPEND1610
BEADBC1602
BEADBC1601
OPENR1653
100R1611
0.22/310V
C1612
OPENR1629
WIREBC1603
0.033/5WR1624
470P/2KVC1626
OPENR1655
OPENR1654
OPENR1630
WIREBC1604
OPENC1615
4
3 2
1
IC1703OPEN
4
3 2
1
IC1702TLP781F
270KR746
RS1KJTDD714
1500P/2KV
C726270KR747
TK3A65DQ601
G
D
S
Q1602TK8A50D
G
D
S
Q1601TK8A50D
G
D
S
BEADBC1703
Q1704TK5A65D
G
D
S 1000P/2KV
C1706
0.15/2WR1719
1ZB36BBD1707
RS1GJTDD1705
10R1714
22KR17181000P
C1710OPEND1710
180R1712
820KR1707
2.7KR1702
0.1C1704150P
C1702
220PC1703
OPENR1709
OPENR1701
5
6
7
81
4
3
2
IC1701FA5640N
ZCD
GND OUT
VCC
NU
VH
IS
FB4.7KR1703
1000PC1701
OPEND1704
22KR1704
33/400VC1708
4
3 2
1
IC1603OPEN
4
3 2
1
IC1602TLP781FQ1604
2SC5344SY
47R16342.7K
R1633
TFZVTR16BD1608 C1618
10/50V
680R1637 2SA1576UBTLQ
Q1607
18KR1638
Q1608KTC3875S-Y-RTK/P
10KR1639
4.7R1656
10KR1642
4.7KR1640
0.1C1624
Q1701KTC3875S-Y-RTK/P
Q17022SA1576UBTLQ
22KR1710
10KR1711
22KR1708C1709
220/10V
27KR1705
270R1720
1000P/250VC1707
2200P/1KVC725
D712SB3200BR
D711SB3200BR
D710SB3200BR
VIN
2.2KR738
TFZVTR27BD1711
0.1C722
1.8KR741
OPEND1713 C723
470/63VC724470/63V
C1001470/63V 1/100V
C1004
15KR739
2.7KR740
D704SL431A-AT 3.3K
R745
1.3KR7440.1
C721 43KR743
0.01C691
330R692
Q691KTC3875S-Y-RTK/P
HSC119D663
C69233/35V 47K
R693
2.2KR691
HSC119D662
GP002OPEN
220/35VC616
0.22/310V
C601
GP003EARTH PLATE
47KR668
Q6572SA950-O
1
2
3
6
7
15
14
13
12
11
10
5
T601POWER TRANS
1 8
4 5
T1601TE2520A7001
1 8
4 5
T1602TE2520A7001
2
3
4
6
7
15
14
13
11
10
T1701POWER TRANS
270R634
OPEND614A
4
3
1
2
ERRORVOLTAGE DET
HOT CIRCUIT. BE CAREFUL.
0.7
0(SWITCHING)
A FB C D E G
HOT COLD
0
1.7
231.2
(SWITCHING)
0
POWER SUPPLY CBA
2.5
1.3
1.0 153.7
0
20.90.1
0
0.7
(RESET)
26.515.6
17.6
1.1
20.1
21.1
0
(SWITCHING)
(SWITCHING)
(SWITCHING)
0
0
0.6
00
0
0 (RESET)
03.33.3
3.33.300
0
0
3.32.8
00
0
12.7
21.2
0 3.3
(+3.3V REG.)
12.6
CONTINUEPOWER SUPPLY 2
CONTINUEPOWER SUPPLY 2
SHUNTREGULATOR (SWITCHING)
ZCDA
0
HVSEN
GDB
PHB
6.0ZCDB
COMP
GND
VREF3.0
1.4
VCC
GND
0
0
6.0
15.6
TSET
0
0.8
6.0
VSENSE
3.6
1.4
PWMCNTL
(SWITCHING)
6.8
0
6.8
VINAC CS
1.4
GDA
(SWITCHING)
(SWITCHING CONTROL)
1.7
0
6.8
ERRORVOLTAGE DET
104.0
(SWITCHING)
14.6
14.6
2.6
0.1
1.0
5.20
SWITCHINGCONTROL
104.0
(ISOLATOR)(SWITCHING)
(SWITCHING)
(SWITCHING)
(SWITCHING)
(SWITCHING)
(SW+15V)
15.6 21.616.2
21.6 21.720.9
0
0.70
15.6 15.615.0
0
00.6
0.1
214.0
4.9
0
1.1-0.2
02.5
1.9
0
0
3.3
12.7
12.712.7
21.221.221.2
0
2.6
25.4
26.4
21.7
21.5
1.8
0.7
0.71.4
0.7
SWITCHINGCONTROL
2.325.4
0
2.420.1
0
TO DIGITAL MAINCBA UNIT CN3601 or CN3602
3.310.5
9.9
(+3.3V REG.)
(9.9)
PL13.14SCP1
Power Supply 1 Schematic Diagram
NOTE:The voltage for parts in hot circuit is measured using hot GND as a common terminal.
CAUTION !Fixed voltage (or Auto voltage selectable) power supply circuit is used in this unit. If Main Fuse (F602) is blown , check to see that all components in the power supply circuit are not defective before you connect the AC plug to the AC power supply. Otherwise it may cause some components in the power supply circuit to fail.
For continued protection against risk of fire, replace only with same type 2.5A, 250V fuse.
CAUTION ! :
ATTENTION : Utiliser un fusible de rechange de même type de 2.5A, 250V.2.5A 250V
10-4
1/100VC1107
1/100VC1108
1KR1108
SB2150BDD1102
100KR1119
110KR1120
CN10011 VLED12 ILED1
1/100VC1102
1/100VC1103 100uH
L1101
120R1102
120R1101
10R1123
HSC119D1103
100/100VC1105
1/100VC1109
1C1110
0.18/1WR1115
100/63VC1101
TFZGTR39CD1105
2.2KR1128
1.8KR1129
8
3
2
10
1
7 12
VCC
UVLO
9
6
11
13
4
ADIM
GND
5 14
15
16
17
18OVP
CONTROLLOGIC
SS
RT
FAILDETECT
VREG
DRIVE
DRIVE
ADIM-P
IC1101BD9488F-GE2
75KR1103
0.047C1112
62KR1114
240KR1111
1KR1122
0.022C1115
1KR1124
51R1125
2200PC1117
1R11271R1126
D1107HSC119
560PC1119
Q1101AP18T10AGH-HF
GD
S
Q1102AP18T10AGH-HF
GD
S
BACKLIGHT-SW
VIN
AMP+13V
BACKLIGHT-ADJPROTECT3
3KR111333KR1112
1C1114
2200PC1116
10KR1121
20KR1105
20KR1104 OPEN
C1111 3 VLED24 ILED25 VLED36 ILED3
200R1118
1000PC1113
OPENR1117OPENR1116
100KR1110
10KR1109
100KR1107
10KR1106
OPEND1106
0R1130
BC1102WIRE
BC1101BEAD
1/100VC1118
1/100VC1309
1/100VC1308
10R1323
33KR1312
1/100VC1303
0R1330
100/63VC1301
0.18/1WR1315
1KR1322
120R1301
75KR1303
D1307HSC119
560PC1319
1R1327
OPENR1316
BC1301BEAD
10KR1309
SB2150BDD1302
20KR1304
240KR1311
2200PC1316
1C1310
OPEND1306
100uHL1301
100/100VC1305
Q1301AP18T10AGH-HF
GD
S
OPENR1317
2.2KR1328
BC1302WIRE
1KR1308
100KR1319
1000PC1313
0.047C1312
1KR1324
3KR1313
10KR1321
200R1318
120R1302
0.022C1315
1/100VC1302
1/100VC1318
2200PC1317
OPENC1311
51R1325
1R1326
110KR1320
62KR1314
1.8KR1329
8
3
2
10
1
7 12
VCC
UVLO
9
6
11
13
4
ADIM
GND
5 14
15
16
17
18OVP
CONTROLLOGIC
SS
RT
FAILDETECT
VREG
DRIVE
DRIVE
ADIM-P
IC1301BD9488F-GE2
1C1314
10KR1306
Q1302AP18T10AGH-HF
GD
S
HSC119D1303
1/100VC1307
100KR1310
100KR1307
TFZGTR39CD1305
20KR1305
1R1226
20KR1205 0.022
C1215
10KR1209
1R1227
100KR1210
100/63VC1201
240KR1211
BC1202WIRE
SB2150BDD1202
0.047C1212
100/100VC1205
0.18/1WR1215
1.8KR1229
Q1202AP18T10AGH-HF
GD
S
1C1210
10KR1206
OPEND1206
D1207HSC119
51R1225
TFZGTR39CD1205 BC1201
BEAD
2.2KR1228
33KR1212
20KR1204 OPEN
C1211
100KR1207
1/100VC1207
HSC119D1203
2200PC1216
1KR1208
62KR1214
2200PC1217
1/100VC1218
3KR1213
1/100VC1203
1/100VC1202
75KR1203
120R1202
1000PC1213
120R1201
110KR1220
200R1218
100KR1219
1C1214
10R1223
Q1201AP18T10AGH-HF
GD
S
1/100VC1209
1/100VC1208
1KR1222
8
3
2
10
1
7 12
VCC
UVLO
9
6
11
13
4
ADIM
GND
5 14
15
16
17
18OVP
CONTROLLOGIC
SS
RT
FAILDETECT
VREG
DRIVE
DRIVE
ADIM-P
IC1201BD9488F-GE2
1KR1224
560PC1219
0R1230
100uHL1201
10KR1221
BEADL1103
L1102BEAD
BEADL1303
BEADL1203
L1202BEAD
L1302BEAD
GP001EARTH PLATE
(SWITCHING)
LED BACKLIGHTDRIVER
82.50.8
POWER SUPPLY CBA
TO LCD PANELASSEMBLY
(SWITCHING)
1
2
3
4
H LKJI M
CONTINUEPOWER SUPPLY 1
0.778.0
0.882.3
LED BACKLIGHTDRIVER
(SWITCHING)
(SWITCHING)
CONTINUEPOWER SUPPLY 1
4.3
10.2
1.6
5.4
0.1
10.2
0.8
2.7
(SWITCHING)
0
0.8
2.7
5.6
0.8
2.85.4
4.4
5.4
2.7
(SWITCHING)10.2
3.3
2.9
LED BACKLIGHTDRIVER
0.1
45.9
2.9
10.2
2.8
0.1
10.2
5.4
0
4.4
0.81.6
2.7
2.7
5.6
5.4
5.4
2.7
3.3
2.9
10.2
2.8
0.1
10.2
5.4
0
4.4
0.81.6
2.7
2.7
5.6
5.4
5.4
2.7
3.3
0.14.3
0.8
10.20.8
45.9
0.14.3
0.8
10.20.8
45.9
PL13.14SCP2
Power Supply 2 Schematic Diagram
10-5
4.7KR4003
8.2KR4002
2.7KR4004
18KR4001
2.2KR4005
OPEND4002
0.1C4002
MM5Z5V6BD4001
CN40011GND2KEY-IN1
SW4006 SW4005 SW4004 SW4003 SW4002 SW4001
2.2KR4006
SW4007
2
1
A B C
FUNCTION CBA UNIT
TO IR SENSOR CBA UNIT CN4051
CH UP VOLDOWN
POWER
UNLESS OTHERWISE SPECIFIED:SWITCHES ARE SKRMABE010.
CHDOWN
VOLUP
MENUSOURCE
PL13.14SCF
Function Schematic Diagram
10-6
1000PC4052
OPENC4055
10C4056
10C4051
R405156
R40526.8K
0.1C4054
1
2
3 4
5
6
IC4051PH5502B2NA1-E4
IOUT
GND
VCC NU
GC1
GC2
R405782K
0.1C4057
R4055OPEN
R405810K
R405610K
R4059OPEN
D4051SMLE12WBC7W1HR
0.1C4053
Vcc
GND
V-OUT
2 31
RS4051RS-272
CN40511GND2KEY-IN1
5 REMOTE4 LED1
7 GND6 KEY-IN1
CN40521 AL+3.3V2 P-ON+5V3 LIGHT
R40532.7K
R4060OPEN
R40541K
8 SCL(NU)9 SDA(NU)
2
1
A B C
TO FUNCTION CBA UNIT CN4001
(REMOTE SENSOR)
(LIGHT SENSOR)
POWER
IR SENSOR CBA UNIT
TO DIGITAL MAINCBA UNIT CN3101 or CN3105
PL13.14SCIR
IR Sensor Schematic Diagram
10-7OP
ENR3
882
6 TP
3PC3
905
OPEN
R388
1
7 GND
3 OE1
7GND
25 P-ON+3.3V
6GND
29PANEL-SDA
28 GND
30GND
12 LVDS-OD3(+)M4
M7
OPEN
R388
0
22LVDS-OCLK(+)
L6
OPEN
R392
8OP
ENR3
884
J3
5 POL
27 VCOM
28PANEL-SCL
18 LVDS-OD2(+)
H4
2 OE2
27 VCOM
21 LVDS-OD1(-)
3PC3
912
29 LCD+21V
LCD-P-ON
26 PWR-CTRL
16 LVDS-OCLK(-)
M6
C391
4
J1
16 LVDS-OCLK(-)
16LVDS-OD1(+)
9 LVDS-OD5(-)
15 LVDS-OCLK(+)
OPENR3975
18LVDS-OD2(-)
2 OE2
F1
29 LCD+21V
OPEN
C394
1
14 GND
R5OE2
K6
P1NUOPENR3974
23GND
G3
22 LVDS-OD0(+)
1 STV
24LVDS-OD3(-)
H2L5
5 POL
25LVDS-OD3(+)
L4
1 STV
24 GND
3PC3
906
20 LVDS-OD1(+)
10 LVDS-OD4(+)
17 GND
3P 3P 3P
C391
3
19 LVDS-OD2(-)
20GND
21 LVDS-OD1(-)
2LCD+12V
R6TP
OPENR3977
J5
OPEN
C393
8
3PC3
908
N5
OPENR3976
J7 NU
22 LVDS-OD0(+)
P4STV
CN390331 LCD+21V30 LCD+21V
3PC3
911
11GND
26GND
N3OE
23 LVDS-OD0(-)13LVDS-OD0(+)
7 GND
M5 11 LVDS-OD4(-)
13 LVDS-OD3(-)
21LVDS-OCLK(-)
3 OE
OPEN
C394
0
11 LVDS-OD4(-)
K7 NU 8 LVDS-OD5(+)
28 GND
OPEN
R388
3
3PC3
903
19LVDS-OD2(+)19 LVDS-OD2(-)
15 LVDS-OCLK(+)
17GND
L7
23 LVDS-OD0(-)
14GND
12 LVDS-OD3(+)
10NU
4LCD+12V
3PC3
916
9LVDS-SEL
20 LVDS-OD1(+)
26 PWR-CTRL
CN39051LCD+12V
12LVDS-OD0(-)
3PC3
904 6 TP
P3CPV
3PC3
907
9 LVDS-OD5(-)
K5
OPEN
C399
8
17 GND
27BIST
N2 NU
OPEN
C394
2
10 LVDS-OD4(+)
4 CPV
15LVDS-OD1(-)
OPEN
C393
9
C391
5
R3POL
F3
L3
*1IC3101(1/7)MN2WS0270HA
K3
4 CPV
F2
CN390430 LCD+21V
OPENR3978
24 GND
3LCD+12V
13 LVDS-OD3(-)
VCOM-PWM
14 GND
P2 NU
18 LVDS-OD2(+)
25 P-ON+3.3V
8PANEL-WP
J6
H3
8 LVDS-OD5(+)
OPENR3979
5GND
9LVDS-OCLK(+)
23PANEL-WP
10LVDS-OCLK(-)
2PANEL-SDA
18LVDS-OD0(+)
3PANEL-SCL
5GND
1GND
17GND
26GND
19LVDS-OD0(-)
14GND
21NU
7LVDS-OD3(-)
16LVDS-OD1(-)
8GND
13LVDS-OD2(-)
22LVDS-SEL
15LVDS-OD1(+)
4NU
CN390130LCD+12V
24GND
6LVDS-OD3(+)
29LCD+12V28LCD+12V
25GND
20GND
12LVDS-OD2(+)
27LCD+12V
11GND
LCD+12V/+21V
R3915 OPEN
LVDS-ED4(+)
LVDS-OD4(+)
LVDS-ED3(+)
LVDS-OD3(-)
LVDS-ED0(-)
LVDS-OD3(+)
LVDS-OD0(+)
LVDS-OCLK(-)
LVDS-OD1(+)
LVDS-ED1(+)LVDS-ED2(-)
LVDS-ED0(+)
LVDS-ECLK(+)
LVDS-OCLK(+)
LVDS-ED3(-)
LVDS-OD2(+)
LVDS-ED1(-)
LVDS-OD0(-)
LVDS-OD1(-)
LVDS-ED2(+)
LVDS-ED4(-)
LVDS-OD2(-)
LVDS-ECLK(-)
LVDS-OD4(-)
C392
7
3PC3
925
3PC3
919
C392
6
3PC3
921
3P 3P3P
C392
4
3PC3
920
3PC3
923
3PC3
922
R3914 OPEN
J2
R3913 OPEN
K4
3PC3
918
3PC3
917
3PC3
928
P-ON+21V
OPENR3909
OPENR3910
OPENR3908
OPENR3907
PANEL-WPPANEL-SCLPANEL-SDA
3 PANEL-SCL4 PANEL-SDA
CN39071 GND2 PANEL-WP
VCOM-DC
OPENR3931
Q3901OPEN
OPENR3924
OPENR3935
OPENR3932
OPENR3934
OPENR3933
OPENC3947
OPENC3948
P-ON+3.3V
OPENR3904OPENR3906
0R3925
BACKLIGHT-ADJ
P7 BACKLIGHT-ADJ
OPENR3901
VCOM-PWM
10KR3916
3
(NO CONNECTION)
FE
4
C
(NO CONNECTION)
TO DIGITAL MAIN 6IC3101(5/7)
1
LVDSTX
DIGITAL SIGNAL PROCESS/MAIN MICRO CONTROLLER
CONTINUEDIGITAL 2
DIGITAL MAIN CBA UNIT
A B D
2
(NO CONNECTION)
CONTINUEDIGITAL 2
CONTINUEDIGITAL 2
CONTINUEDIGITAL 7
CONTINUEDIGITAL 4
CONTINUEDIGITAL 7
(NO CONNECTION)
(NO CONNECTION)
Digital Main 1 Schematic Diagram [TYPE A]
PL13.14ASCD1
The order of pins shown in this diagram is different from that of actual IC3101. IC3101 is divided into seven and shown as IC3101 (1/7) ~ IC3101 (7/7) in this Digital Main Schematic Diagram Section.
1 NOTE:
10-8
50PANEL-SCL
OPENR3867
OPENR3896
OPENC3902
6GND
49PANEL-SDA
OPENC3909
24LVDS-OD0(-)
46LCD-P-ON
OPENR3866
D39021SS400
31GND
9GND
2LCD+12V
12LVDS-OD4(-)
44NU
11LVDS-OD4(+)
7GND
16LVDS-OCLK(+)
LCD-P-ON
OPENR3941
25GND
39LVDS-ED0(+)
CN39061LCD+12V
4LCD+12V
13LVDS-OD3(+)
19LVDS-OD2(+)
22LVDS-OD1(-)
37LVDS-ED1(+)
23LVDS-OD0(+)
8GND
OPENR3905
30LVDS-ED3(-)
PROTECT3
27LVDS-ED4(+)28LVDS-ED4(-)
40LVDS-ED0(-)
OPENR3891
18GND
51PANEL-WP
45VCOM
OPENR3900
OPENR3940
OPENR3903
OPENR3923
34GND
36LVDS-ED2(-)
21LVDS-OD1(+)
43NU
OPENR3899
42NU
OPENR3926 OPENC3910
35LVDS-ED2(+)
OPENR3869
OPENC3996
3LCD+12V
29LVDS-ED3(+)
OPENR3897
26GND
14LVDS-OD3(-)
33LVDS-ECLK(-)
Q3905OPEN
1
2
3 6
7
8
4 5
48NU
Q3904OPEN
OPENR3942
10GND
32LVDS-ECLK(+)
OPENC3997
38LVDS-ED1(-)
OPENR3922
47NU
20LVDS-OD2(-)
15GND
17LVDS-OCLK(-)
VCOM-PWM
OPENR3902
5NU
41GND
OPENR3898
0.047C3946
OPENC3951
1500PC3950
24KR3936100P
C3955 33KR3938
6.8KR39393.3K
R3937
LCD+12V/+21V
0.1C3949
OPEND3905
OPENR3952
D3906OPEN
4.7C3943
OPENC3944
0.1C3945
L390122uH
C39584.7OPEN
C39594.7C3956
4.7C3954
OPENR3911
OPENR3912 C3952
OPEND3901OPEN 4.7
C3953
6.8KR3550
P-ON-H2
OPENR3895
1000PC3992
4.7C3991
4.7C3901
OPENR3982
VCOM-DC
P-ON+3.3V
LVDS-ED3(+)LVDS-ED3(-)
LVDS-ECLK(-)LVDS-ECLK(+)
LVDS-ED2(-)LVDS-ED2(+)
LVDS-ED1(-)LVDS-ED1(+)
LVDS-ED0(+)LVDS-ED0(-)
LVDS-ED4(-)LVDS-ED4(+)
R3985R3984
OPENR3986OPENR3987
R3919 0x4
LVDS-OD2(-)LVDS-OD2(+)
LVDS-OD1(+)LVDS-OD1(-)LVDS-OD0(+)LVDS-OD0(-)
LVDS-OCLK(-)LVDS-OCLK(+)
R3920 0x4
R3980R3981
0R3921000
R3943
LVDS-OD4(-)LVDS-OD4(+)
LVDS-OD3(-)LVDS-OD3(+)
OPENR3988OPENR3989
0R3983
0R39170R3918
PANEL-SDA
PANEL-WPPANEL-SCL
0R3990
P-ON+21V
1
2
3
4 5
6
7
8
IC3901MP1472GJC452Z
SS
EN
COMP
FB GND
SW
IN
BST
CONTINUEDIGITAL 1
DIGITAL MAIN CBA UNIT
H
3
4
J
1
2
LI KG
CONTINUEDIGITAL 1
CONTINUEDIGITAL 8
CONTINUEDIGITAL 6
CONTINUEDIGITAL 7
CONTINUEDIGITAL 2
TO LCD PANELASSEMBLY
(+12V REG.)
00
Digital Main 2 Schematic Diagram [TYPE A]
PL13.14ASCD2
10-9
D17
C3
B2
C2C1
A6
C5
F11
B4
B5
C9
D7
C8
B1
E6
56R3417
D16
A4
C6
C16
C7B7C4
D8
D19
B3A3
A2
B14
C18
C17B18
A14
B13B17
C13
A17
D11
B12
D15C15
A12
C11
B15C14
C12C19
B9B10
F10
D12E11
F14
56R3418
F12
G10
270R3421270R3423
D4
F19
10KR3419
L2 CS#
K1 ODT
F9VSSQ7
0.1C3414
10C3431
G3 DQSL#
F1VDDQ7
J2VSS5
10C3411
D2VDDQ5E9VDDQ6
B1VSSQ1
NU J9
C1VDDQ3
K9CKE
NU J1
R1VDD8
H9VDDQ9
B2VDD1
220R3427
D1VSSQ3
G1VSSQ8
N9VDD7
L1NU
P9VSS10
K8VDD5
CK J7
270R3425
M8VREFCA
K7CK#
M1VSS7
B7 DQSU#
R9VDD9
M9VSS8
D8VSSQ4
E8VSSQ6
A1VDDQ1
C9VDDQ4
G9VSSQ9
T9VSS12
D3 DMU
NU L9
A8VDDQ2
E1VSS3
J8VSS6
E7 DML
A9VSS1
K2VDD4
H2VDDQ8
E2VSSQ5
H1VREFDQ
C7 DQSU
B9VSSQ2
L3 WE#
K3 CAS#
P1VSS9
G7VDD3
0.1C3413
G8VSS4
B3VSS2
J3 RAS#
T1VSS11
F3 DQSL
D9VDD2
N1VDD6
DQL3F8
DQU5A2
DQU0D7
DQU3C2
DQL0E3
DQL5H8
DQU7A3
DQL4H3
DQL7H7
DQU4A7
DQL2F2
DQU6B8
DQU1C3DQU2C8
DQL6G2
DQL1F7
240R3428
L8 ZQ
B1VSSQ1
J2VSS5
DQU7A3
DQL1F7
DQL3F8
G7VDD3D9VDD2
P1VSS9
B7 DQSU#
DQL2F2
D3 DMU
A9VSS1
M8VREFCA
DQL0E3
E1VSS3
0.1C3422
H1VREFDQ
R1VDD8
K3 CAS#
DQL5H8DQL6G2
CK J7
C9VDDQ4
H2VDDQ8
E9VDDQ6
0.1C3424
G3 DQSL#
240R3432
T1VSS11
DQU4A7
220R3431
M1VSS7
N9VDD7
C1VDDQ3
DQU3C2
T9VSS12
P9VSS10
B3VSS2
L2 CS#
DQU2C8
F9VSSQ7
D8VSSQ4
A8VDDQ2
E2VSSQ5
0.1C3423
L3 WE#
DQL7H7
A1VDDQ1
D2VDDQ5
G8VSS4
K9CKE
C7 DQSU
B2VDD1
DQU0D7
G1VSSQ8
DQU1C3
NU J1NU J9
10C3420
K2VDD4
0.1C3421
N1VDD6
F3 DQSL
M9VSS8
10C3432
DQL4H3
K1 ODT
R9VDD9
K8VDD5
NU L9
L8 ZQK7CK#
F1VDDQ7
E8VSSQ6
E7 DML
DQU6B8
J8VSS6
270R3429
H9VDDQ9
D1VSSQ3
J3 RAS#
L1NU
DQU5A2
B9VSSQ2
G9VSSQ9
T2 RESET# T2 RESET#
VCC+1.5V
0.1C3418
0.1C3417
0.1C3426
0.1C3425
0.1C3419
0.1C3429
270R3426
270R3430
0.1C3428
0.1C3430
BA2M3
BA0M2BA1N8
BA0M2BA1N8BA2M3
A1P7
A5P2
A8T8
A3N2
A9R3A10/APL7
A7R2
A13T3
A11R7
A14T7
A0N3
A12/BC#N7
A2P3
A6R8
A4P8
NU
IC3401K4B1G1646G-BCK0
M7A14T7NU
IC3402K4B2G1646G-BCMA
M7
A13T3
A1P7A2P3
A0N3
A12/BC#N7
A8T8
A4P8
A7R2A6R8
A9R3
A3N2
A5P2
A11R7A10/APL7
56R3412
D3
IC3101(2/7)*1
MN2WS0270HA
D6270R3411
0.1
C340
927
0R3
422
0.1
C341
027
0R3
424
270
R341
00.
1C3
406
240R34201C3405
D1
G7
0.1C3427
0.1C3416
0.1C3415
0.1C3412
1C3408
56R3416
OPENC3407
G11E8G8E7E19F18E18E17D18F17F16E16D10E10D9G9
G16E15D14E14
R3409 56x4
R3405 56x4
R3406 56x4
R3407 56x4
R3408 56x4
56R341456R3413
56R3415
G12
10KR3433AL+3.3VT5
OPENR3401
OPENC3401
OPENC3402
OPENR3402
OPENR3403
OPENC3403
OPENC3404
OPENR3404
MMXCK
MMDM2
MMDM1
MMDQ21
MMDQ10
MMDQ12
1
MMDQ30
MMXCS1
M
MMDQ15
P
MMDQ19
MMDQ28
MMDQ5
MMDQ27
MMDQS1
MMDQ26
MMDQ16
MMDQ20
Q
MMDQ8
MMVREF0
MMDQ25
MMXRAS
MMDQ14
3
N
MMDQ29
MMDQ9
MMCKE0
MMDM3MMDM0
MMDQS3
MMDQ0
MMDQ23
MMDQ1
MMDQ22
MMDQ17
MMDQS2
R
MMCK
MMDQ3
MMDQ7
MMDQ4
MMXCS0
4
2
MMDQ13
MMDQ2
MMDQ6
O
MMDQ31
MMODT0
MMDQ11
MMDQ18
MMDQ24
MMDQ31MMDQ30MMDQ29MMDQ28MMDQ27MMDQ26MMDQ25MMDQ24MMDQ23MMDQ22
MMDQ20MMDQ19MMDQ18MMDQ17MMDQ16MMDQ15MMDQ14MMDQ13MMDQ12MMDQ11MMDQ10MMDQ9MMDQ8MMDQ7MMDQ6MMDQ5MMDQ4MMDQ3MMDQ2MMDQ1
MMDQ21
MMDQ0
MAIN MICRO CONTROLLER/DIGITAL SIGNAL PROCESS
MEMORYI/F
TO DIGITAL MAIN 6IC3101(5/7)
DIGITAL MAIN CBA UNIT
MMVREF1
MMXDQS1MMDQS0MMXDQS0
MMXDQS2
MMXDQS3
MMODT1
MMCKE1
MMZQ
MMXRESET
(DDR3 SDRAM)
MMDQ5
MMDQ13
MMDQ0
MMDQ14MMDQ10
MMDQ6
MMDQ8MMDQ12
MMDQ1
MMDQ15
MMDQ3
MMDQ11
MMDQ9
MMDQ4
MMDQ7MMDQ2
MMDQ25MMDQ29
MMDQ23
MMDQ21
MMDQ27
MMDQ24
MMDQ19MMDQ22
MMDQ17
MMDQ18
MMDQ28
MMDQ30
MMDQ31
MMDQ16
MMDQ26
(DDR3 SDRAM)
MMDQ20
MMA0
MMA9
MMA12
MMA5
MMA1
MMA14
MMA6
MMA2
MMA10
MMA8MMA7
MMA13
MMA4MMA3
MMA11
MMA14
MMA6MMA5
MMA1
MMA12
MMA2
MMA7
MMA4
MMA8
MMA10
MMA3
MMA11
MMA9
MMA13
MMA0
MMVREF2
DDR3VOUT
NU
MMA2 MMA2
MMA6 MMA6
MMA8 MMA8
MMA14 MMA14
MMA9 MMA9
MMA11 MMA11
MMA13 MMA13
MMA7 MMA7
MMA4 MMA4MMA5MMA5MMA1MMA1
MMA12 MMA12
MMBA1MMA10MMA10
MMA3 MMA3
MMA0 MMA0
MMBA2MMBA0MMXWEMMXCAS
NU
CONTINUEDIGITAL 7
DDRPWRON
Digital Main 3 Schematic Diagram [TYPE A]
PL13.14ASCD3
The order of pins shown in this diagram is different from that of actual IC3101. IC3101 is divided into seven and shown as IC3101 (1/7) ~ IC3101 (7/7) in this Digital Main Schematic Diagram Section.
1 NOTE:
10-10
P22NU
M20 NU
VCOM-PWM
1KR3118
R3204 75
V20 NU
W17NU
T19NU
Y21 NU
X310125MHz
AE4 AXI
C25 NU
R319256x4
L20 NU
AB22 NU
F24 NU
W19 NU
E23 NU
Y22 NU
AD20NU
C31250.1
D24 NU
10K
R312
8
M21 NU
W18NU
G21 NU
AD19NU
AC20NU
10KR3111
AA20NU10
KR3
123
F23 NU
R3201 75
10KR3113
B21MMCDAT4
AA21NU
R3202 75
J24NU
N21 NU
AD4 AXO
D20 NU
OPENR3169
U19 NU
AD8 NU
AL+3.3V
J25NU
R319156x4
J22NU
1KR3224
1
2
3
4
5
6
7
9
10
8
11
12
13
15
16
14
17
18
19
20
21
30
28
27
42
29
26
25
40
39
24
23
22
41
38
37
36
34
33
35
32
31
43
44
48
45
46
47
IC3102H27U1G8F2BTR-BC
K20 NU
AB7 NU
R3190 75
J23 NU
A24XNFWE
OPENR3130
N19 NU
10K
R313
2
U9 NU
Y17NU
OPENR3127
AA19NU
P21NU
G4 NU
R22NU
4TRSTN
E21XNFRE
Y8 NU
J20 NU
H20 NU
OPENR3125
P-ON+5V
T20NU
OPENR3115
G24NU
L21 NU
R20NU
W21 NU
OPENR3122
5JTMS
7JTDI
T21NU
AB23 NU
R3205 22
U20 NU
H21 NU
E24 NU
AE20NU
AC5 NU
E20MMCDAT5
K19 NU
STB-RESET
F20NU
F22 NU
COMP-DET
AB20NU
AA17NUL19 NU
W20 NU
AA18NU
P24NU
H23NU
AA22 NU
P25NU
10K
R317
3
V21 NU
C20MMCDAT7
N20 NU
K22NU
V19 NU
R21NU
AA7 NU
J19 NU
D21MMCDAT2
C23NFCLE
C31260.1
STMTIME1
B20MMCDAT6
10KR3136
10K
R312
4
M19 NU
L2 HP-DET
B22
IC3101(3/7)*1
MN2WS0270HA
MMCDAT0
AB18NU
M3 NU
F25 NU Y19NU
12PC3124
K21 NU
U21 NU
G6 NU
H22NU
100R3112
P6 VCOM-PWM
AB19NU
R3203 75
AC19NUY16NU
15PC3128
6JTDO
A23XNFCE
D25 NU
B24XNFWP
10K
R312
1
CN310410GND
R19NU
OPENR3126
1AL+3.3V10KR3198
3EVTRG
C22NU
2XRST
C21MMCDAT3
R3189 75
P-ON+3.3V
B23NFALE
H6 COMP-DET
G22NU
100R3129
A22MMCDAT1
OPENR3116
OPENR3208
A20 NU
Y20NU
8EJTCK
D22NANDRYBY
P19 NU
150R3170
P20 NU
Y18NU
G23NU
9NU
OPENR3210
H19 NU
W16NU
W15NU
HP-DET
OPENR3135
W
1
T
3
4
2
VS U X
(NO CONNECTION)
NU MMCDAT0
MMCDAT4
R/B
NU
NU
I/O3
NU
DIGITAL SIGNAL PROCESS/MAIN MICRO CONTROLLER
VCC
NU
NU
NU
MMCDAT5
CLE
NU
NU
NU
MMCDAT2
NU
NU
WP
NUMMCDAT2
DIGITAL MAIN CBA UNIT
NU
NU
VSS
I/O4
MMCDAT3
CONTINUEDIGITAL 7
MMCDAT0
NU
(NAND FLASH MEMORY)
NU
CE
MMCDAT4MEMORYI/F
NU
MMCDAT7
MMCDAT6
WE
MMCDAT1
MMCDAT1
I/O2
VCC
I/O0
MMCDAT5
TO DIGITALMAIN 6IC3104(5/7)
NU
I/O5
MMCDAT7MMCDAT6
NU
NU
RE
NU
NU
I/O6
CONTINUEDIGITAL 8
NU
I/O7
ALE
VSS
MMCDAT3
NU
NU
NU
NU
I/O1
NUCONTINUEDIGITAL 1
CONTINUEDIGITAL 6
Digital Main 4 Schematic Diagram [TYPE A]
PL13.14ASCD4
The order of pins shown in this diagram is different from that of actual IC3101. IC3101 is divided into seven and shown as IC3101 (1/7) ~ IC3101 (7/7) in this Digital Main Schematic Diagram Section.
1 NOTE:
10-11
C24 UART0TX
N24 USB0OD
N23 USB0VBUS
N22 USB0(-)M24 USB0(+)
OPEND3001
OPENC3003
AB9NU
AE9
AD9
AA13IF-AGC
Y15TU-SCLAA16TU-SDA
Y12NUAA15NU
33R300633R3007
39PC3013
L30033.3uH0.1
C3011
0.1C3014 L3004
3.3uH
OPENC3010
OPENC3002
OPEND3002
C37391
L3706OPEN
1
2
3 4
5
IC3701AP2151WG-7
VOUT
GND
/FLAG EN
VIN
AB8 NU
K23 NUK24 NU
P-ON+3.3V
4GND
CN37041USB+5V
3USB0(+)2USB0(-)
TU3001TUNER UNIT
1
+3.3V
2
GND
3
SDA
4
SCL
5
IF-AGC
6
DIF-OUT1
7
DIF-OUT2
OPEND3010
270R3005
270R3003OPEN
C3026
OPENC3027
OPENC3117
UARTOTX 2100R3175
R310110K
UARTORX 3E22 UARTOTX
R3108OPEN
100R3176
P-ON+5V 1
CN3101GND 4
OPENC3116
C3742220/6.3V
R376110K
100R3758
0.1C3727
2.49KR3172
10kR3177
OPENC3115
AC9NU
W14NUW10NU
MM5Z5V6BD3007OPEN
C303910C3040
OPENC3041
L30052.2uH
4.7KR30114.7KR3025
P-ON+5V
10KR3001
0.1C3009
10KR3004
Y13NUW8NUAA8NU
4GND
CN37011USB1(+)
CN37054USB+5V
3USB+5V
3USB1(-)2USB1(+)
2USB1(-)
6GND5GND
1GND
L3701OPEN
L23 USB1(+)M22 USB1(-)
M25 USB1VBUS
C3716OPEN
1
2
3 4
5
IC3702OPEN
VOUT
GND
/FLAG EN
VIN
OPENR3702
R3704OPEN
C3715OPEN
OPENC3714
0R3734
0R3736
R3735OPEN
UART1RXUART1TX
100R3194G20 UART1TX
1KR3217
100R3193F21 UART1RX
M1
IC3101(4/7)*1
MN2WS0270HA
NUN4 NUM2 NUP5 NU
B25 NUD23 NU
R6 RX(-)
R2 TCT
C37010.01
R1 TX(+)
CN3706R8 GND
C37440.01
R3 TX(-)
R5 RCT
R7 NU
R4 RX(+)
AC8RX(-)
AC7RX(+)AE6TX(-)
AD6TX(+)
U10NU
AC6CTRL11 CTRL11C31291
0.1C3008
10KR3180M23 USB10D
Z AC
1
4
2
ABY AA
3
AD
DIGITAL SIGNAL PROCESS/MAIN MICRO CONTROLLER
CONTINUEDIGITAL 7
TO DIGITAL MAIN 6IC3101(5/7)
TO DIGITAL MAIN 6IC3101(5/7)
DEMODULATOR/MPEGDECODER
DIGITAL MAIN CBA UNIT
(USB JACK)
(HIGH SIDE SWITCH)
(NO CONNECTION)
(NO CONNECTION)
WIRELESS LAN MODULE
(ETHERNET JACK)
CONTINUEDIGITAL 8
CONTINUEDIGITAL 7
Digital Main 5 Schematic Diagram [TYPE A]
PL13.14ASCD5
The order of pins shown in this diagram is different from that of actual IC3101. IC3101 is divided into seven and shown as IC3101 (1/7) ~ IC3101 (7/7) in this Digital Main Schematic Diagram Section.
1 NOTE:
10-12
AC18
OPEND3804
OPENC3830
OPENR3807
OPENC3810
1C3819
47KR3825
OPENC3833
OPENR3803
0.22C3803
100KR3812
1C3823
SP3802SPEAKERR-CH
0.047C3827
OPENR3802
1
2
3
4
27
28
26
25
22
24
23
21
6
5
8
7
10
11
12
9
13
14
18
20
15
19
16
17
CONTROLLOGIC
AVCC
POWERLIMIT
PWMLOGIC DRIVE
GAINCONTROL
DRIVE
DRIVE
POWERLIMIT
PWMLOGIC DRIVE
GND
GVDD
NU
PBTL PVCCR
PVCCR
GND
GND
PVCCL
PVCCL
IC3803TPA3110D2PWPR
L380210uH
0.047C3824
10C3842
2SC4081UBTLQQ3822
1000PC3814
0R3820
0.22C3801
1C3816 OPENC3808
1C3817
OPENR3805
0R3806LCD-P-ON
OPEND3801
10KR3824
1C3822
SP3801SPEAKERL-CH
2.2C3825
OPENR3801
OPENC3832
OPENR3826
OPENR3804
10R3813
1C3821
1000PC3813
1C3815
L380310uH
1000PC3812
1C3805
OPENC3809
0.22C3804
1C3820
L380110uH
L380410uH1C3806
OPENC3807
1KR3811
OPENR3810
OPEND3802
Q38212SA1576UBTLQ
OPEND380310K
R3808
0.22C3802
1000PC3811
10KR3809
220/16VC3829
10C3843
1C3818
CN38011 SP(L)+
4 SP(R)+
2 SP(L)-3 SP(R)-
OPENC3837
OPENC3835
OPENC3836
OPENC3834
OPENC3840
OPENC3841
OPENC3839
OPENC3838
2.2C3828
10KR3822
0R3821
AB17
AUDIO-MUTE
OPENR3816
OPENR3815
OPENR3814
OPENR3818
OPENR3819
OPENR3817
P-ON+3.3V
220/16VC3826
100/16VC3831
1.8KR3823
OPENR3828
SP-MUTE
E2 AUDIO-MUTE
3.3R3729
OPENC3718
P-ON-H2
220/6.3VC3712
OPENR3744
OPENR3732
10KR3738
4.7KR3733 47K
R3751
OPENQ3708
10KR3743
OPENR3739
OPENR3740
OPENQ3710
OPENR3752
HEADPHONEJACK
JK3801
OPENR3731
3.3R3728
OPENQ3701
R3713OPEN
220/6.3VC3713
10KR3746
10KR3737
W11
D3704OPEN
47K
R383
9
1C3119
R3220 100
1C3105
1C3120
R3145 36
AC14
D3701OPEN
110R3726
75R3171
R3218 10
56PC3710
D371
4OP
EN
1C3121AC10 NU
AC13
AE17 NU
1C3109
10KR3724
R3154 100
D371
6OP
EN
R3149 36
39PC3703
33R3741
D3707OPEN
1C3102
R3221 100
R3298 100K
100R3727
JK3701
33PC3707
220R3725
10K
R383
0
AD12 NU
AB13JK3706
Y9 NU
AB16 NU
10KR3723
R3297 100K
AB14 NU
AB10
IC3101(5/7)*1
MN2WS0270HA
1C3208
AC11100PC3720
75R3163
10K
R383
1
10R3214
56PC3711
AE141C3207
D3703OPEN
47K
R383
8
AB11R3219 10
AB12
10KR3709
2SC4081UBTLQQ3709
1C3118
F4SPDIF
R3222 100
75R3166
10KR3708
AD16 NUD371
11S
S400
D371
3OP
EN
1
2
3
4
5
14
13
12
11
15
6
7
8
9
10
JK3713PC-RGB-IN
AD11
1C3704COMP-DET
AC16 NUD3
717
OPEN
R3147 36
R3155 100
D371
5OP
EN
Y11 VGA-HSYNC
Y10 NU
1C3103
R3216 1075R3164
D3705OPEN
D3702OPEN
AA11
75R3168
1C3709
AA10
R3148 36
1C3114
AD13
39PC3770
AE12 NU
1C3104
AC12 NU39PC3705
AA12 VGA-VSYNC
100PC3708
AA9 NU
1C3113
75R3167
0.01C3706
AC15 NU
D37121SS400
P-ON+5V AD17AC17
F5 ARC-OUT
ARC-OUT
E4 NUD2 NUF6 NUG5 NUE3 NU
R3195 10KR3196 10KR3197 10K
R3199 OPEN
VGA-SDAVGA-SCL
HP-MUTE
HP-DET
AMP+13V
DIGITAL SIGNAL PROCESS/MAIN MICRO CONTROLLER
SW
AUDIOI/F
TO DIGITAL MAIN 8IC3101(7/7)
A/DCONVERTER
TO DIGITAL MAIN 1IC3101(1/7)
DIGITALSIGNALPROCESS
TO DIGITAL MAIN 5IC3101(4/7)
TO DIGITAL MAIN 4IC3101(3/7)
TO DIGITAL MAIN 3IC3101(2/7)
TO DIGITAL MAIN 8IC3101(7/7)
DIGITAL MAIN CBA UNIT
TO DIGITAL MAIN 5IC3101(4/7)
(AUDIO AMP)
3
2
1
4
AE AF AG AH AI AJ
CONTINUEDIGITAL 8
CONTINUEDIGITAL 7
CONTINUEDIGITAL 8
CONTINUEDIGITAL 4
COMPONENT-Y/VIDEO-IN
COMPONENT-Pb-IN
(BUFFER)
AUDIO(L)-IN
COMPONENT-Pr-IN
AUDIO(R)-IN
DIGITAL AUDIO OUT(COAXIAL)
CONTINUEDIGITAL 2
CONTINUEDIGITAL 8
CONTINUEDIGITAL 7
(SWITCHING)
(SWITCHING)
Digital Main 6 Schematic Diagram [TYPE A]
PL13.14ASCD6
The order of pins shown in this diagram is different from that of actual IC3101. IC3101 is divided into seven and shown as IC3101 (1/7) ~ IC3101 (7/7) in this Digital Main Schematic Diagram Section.
1 NOTE:
10-13
1
2
3
4 5
6
7
8
IC3603MP1472GJC452Z
SS
EN
COMB
FB GND
SW
VIN
BST0.033C3607
OPENC3604
1KR360515KR3677
6.2KR3604
L360422uH
0.01C3612
OPENC3967
OPENR3687C3614
10C360310
C360810
1KR3628
3300PC3611
11KR3606
P-ON+3.3VP-ON+21V
4.7C3616
0.1C3615
OPENC3609
4700PC3666
5.1KR3635
C3669OPEN
C367110
0.033C3661
10KR3633
1
2
3
4 5
6
7
8
IC3602MP1472GJC452Z
SS
EN
COMB
FB GND
SW
VIN
BST
4.7C3674
L360310uH
C367010
0.01C3667
OPENC3968
100R3634
OPENC3665
0.1C3675
OPENR3685
OPENC3673
6.2KR3679
100KR3627
C367210
C3668470/4V
C3623OPEN
1
2
3
4 5
6
7
8
IC3607MP1472GJC452Z
SS
EN
COMB
FB GND
SW
VIN
BST
OPENC3631
4.7C3625
33KR3616
0.1C3617
C362810 OPEN
R3696
0.01C3620
OPENC3966
OPENC3618 4700P
C3619
C362110
12KR3678
L360522uH
4.3KR3614
10KR3617
0.1C3632
D3615KDZTR6.8B
D36061SS400
OPENC3644
0.015C3601
2.2KR3625
OPENC3654
0.01C3639
OPENR3613OPEN
R3676
OPENC3642
0R3626
C364110
OPENR3624
4.7C3645
1
2
3
4 5
6
7
8
IC3604RT8293ALZSP
BS
VIN
SW
GND FB
COMP
EN
SS
10C3643
0.015C3638
L360110uH
0.1C3656
0.1C3655
OPENR3689
OPENC3969
C3646OPEN
100R3629
20P-ON+21V
14GND
22P-ON+21V
3PROTECT3
7BACKLIGHT-ADJ
17AMP+13V
9GND
12GND
8AL+3.3V
6P-ON-H2
10GND
21P-ON+21V
4RESET5BACKLIGHT-SW
OPENC3650
23P-ON+21V
2PROTECT1
13GND
16AMP+13V
OPENC3652
19GND
OPENC3676
100R3647
11GND
18AMP+13V
15AMP+13V
CN36011LED-CONT(NU)
100R3620100R3603
32
1 4
IC3601PST8429UR
CDVDD
GND OUT
270R3608
D3603OPEN 1
C3602
R3602220
0.01C3606
56KR3607
OPENR3621
10KR3619
4.7KR3618
2SC4081UBTLQQ3603
1C3610
D36081SS400
D3609OPEN
BACKLIGHT-ADJ
STB-RESET
HP-MUTE
LCD-P-ONBACKLIGHT-SW
P-ON-H2
PROTECT3PROTECT1
2SA1576UBTLQQ3602
D3605MM5Z15B
10KR3615
10KR3622
OPENC3613
0R3630
0R3631
D3607OPEN
10KR3095
1000PC3605
100R3645
D3602 OPEN
D3601OPEN
R3601OPEN
OPENQ3601
R3610OPEN
OPENR3612
10KR3609
R3611OPEN
AUDIO-MUTE
1C3146
1C3184
10C3173
1C3138
M9VDDTCON25-33
AB15AVDDEVE33
N13VDD33-2
1C3141
*BVDDIO15
0R3022
0.1C3131
M12DPAVDD33
L11LVVDD33-1
*DGND
K11LVVDD11
T16AVDDHP33
0R3024
AB21AVDDH33
R31810
*AVDD11 1C3132
R16AVDDAPUSB33
N9FPEN
*CNU
N10VDDSTM11 0.1C3154
1C3145
10C3136
1C3143
U12AVDDVAD11
U15AVDDV33
L3108BEAD
AVDDADA33 T15
1C3152
1C3172
R15AVDDPLL33
0.1C3130
J21VDDSD18-33
R12TESTSEL
1C3137
10C3142
L10VDDSTM33
D5VDDIOCK15
1C3134
1C3140
1C3144
M11LVVDD33-2
0R3023
1C3151
10C3153
1C3175
M13VDDEM18-33
N12VDD33-1
1C3150
1C3185
L31020
AC21AVDDH11AD21AVDDH11
OPENC3133
AFB R4
IC3101(6/7)*1
MN2WS0270HA
0R3223
OPENC3183
2700PC3182
T9AVDD11-CENAB4AVDD11-RXT10DVDD11
0.1C3147
0.1C3148
0.1C3149
CTRL11
N11LVVDD33-3
AVDDDMD33 U11
AVDD33-CEN P10AVDD33-TX P9
STMADAVDD33 M10STMRONA T4
10C3156
1C3178
0.1C3157
1C3179
0.1C3158
0.1C3155
L31032.2uH
L3104BEAD
10C3159
0.1C3160
0.1C3161
0.1C3162
0.1C3163 L3105
BEAD0.1C3164
560R3185
10C3135
10C3165
0.1C3167
10C3166
0R3183
0.1C3169
0.1C3170
0.1C3171
10C3177
0R3184
0.1C3168
0.1C3174
W9VCOMPJ4LVDSRREFL22USBRREFAD14VREF1V5
24KR31861C3180
6.2KR31871C3181
HP-MUTE
LCD-P-ON
1C3139
22KR3623
OPENC3630
AL+3.3VVCC+1.5V
P-ON+21VP-ON+3.3V
P-ON+3.3VP-ON+5VAL+3.3V
P-ON+3.3VP-ON+5V
P-ON+5VP-ON+3.3VAMP+13V
P-ON+3.3VAL+3.3V
P-ON+5V
D3610MM5Z4V3B
L3101BEAD
L3107BEAD
L3106BEAD
APAOANAMALAK
4
3
1
2
DIGITAL MAIN CBA UNIT
(+3.3V REG.)
(+1.5V REG.)
(+5V REG.)
(+1.14V REG.)
TO POWER SUPPLYCBA CN501
(RESET)
(SW+12V)
CONTINUEDIGITAL 1
CONTINUEDIGITAL 8
*A:J11~J17,K12~K17,L14~L17,M15~M17*B:E9,F8,F9,G13~G15,G19
HEAT SINK
DIGITAL SIGNAL PROCESS/MAIN MICRO CONTROLLER
*C:H5,P23,R13,R23,R24,T13,T22,T23,U22,U24,U25, V5,AD1,AD2,AE2*D:A1,A9,A25,C10,D13,E5,E6,E12,E13,F7,F13,F15, G17,G18,H7,H8,J9,J10,K9,K10,L9,L12,L13,M14, N6,N7,N14~N17,P11~P17,R10,R11,R14,R17,T11, T12,T14,T17,U13,U14,U16,U17,W12,W13,Y14, AA14,AC4,AE1,AE25
CONTINUEDIGITAL 5
CONTINUEDIGITAL 6
CONTINUEDIGITAL 1
CONTINUEDIGITAL 3
CONTINUEDIGITAL 2
CONTINUEDIGITAL 4
CONTINUEDIGITAL 5
CONTINUEDIGITAL 6
CONTINUEDIGITAL 8
(SWITCHING)
Digital Main 7 Schematic Diagram [TYPE A]
PL13.14ASCD7
The order of pins shown in this diagram is different from that of actual IC3101. IC3101 is divided into seven and shown as IC3101 (1/7) ~ IC3101 (7/7) in this Digital Main Schematic Diagram Section.
1 NOTE:
10-14
47KR3774
47KR3773
10KR3777
0.1C3750
47KR3778
47KR3780
10KR3784
47KR3785
47KR3781
0.1C3759
47KR3706
47KR3718
0.1C3702
47KR3722
10KR3721
16 HDMI-DATA
12 CLOCK(-)
JK37171 DATA2(+)
6 DATA1(-)
3 DATA2(-)
14 ARC
9 DATA0(-)10 CLOCK(+)
7 DATA0(+)
5 TMDS DATA1 SHIELD
17 GND18 +5V
13 HDMI-CEC
15 HDMI-CLOCK
19 HOT PLUG DETECT
2 TMDS DATA2 SHIELD
4 DATA1(+)
11 TMDS CLOCK SHIELD
8 TMDS DATA0 SHIELD
16 HDMI-DATA
12 CLOCK(-)
JK37161 DATA2(+)
6 DATA1(-)
3 DATA2(-)
14 NU
9 DATA0(-)10 CLOCK(+)
7 DATA0(+)
5 TMDS DATA1 SHIELD
17 GND18 +5V
13 HDMI-CEC
15 HDMI-CLOCK
19 HOT PLUG DETECT
2 TMDS DATA2 SHIELD
4 DATA1(+)
11 TMDS CLOCK SHIELD
8 TMDS DATA0 SHIELD
14 NU
17 GND
19 HOT-PLUG-DETECT
15 HDMI-CLOCK
18 HDMI+5V
16 HDMI-DATA
2 TMDS DATA2 SHIELD
10 CLOCK(+)
JK37151 DATA2(+)
4 DATA1(+)
7 DATA0(+)
5 TMDS DATA1 SHIELD
8 TMDS DATA0 SHIELD
11 TMDS CLOCK SHIELD
3 DATA2(-)
13 HDMI-CEC
6 DATA1(-)
12 CLOCK(-)
9 DATA0(-)
AD24
IC3101(7/7)MN2WS0270HA
*1
AE24AD23AE23AC23AE22AD22AC22
22R3865
27KR3863
D37221SS400
2SC4081UBTLQQ370710K
R3701
1KR3705
OPENR3719
10KR3703
AB24
AA23AA24
AC24AD25
Y23
AC25
AB25
1KR3779
OPENR3783
2SC4081UBTLQQ370210K
R3707
10KR3710
W23
V23V24
Y25Y24
U23
W22
V22
OPENR3776
1KR3775
2SC4081UBTLQQ370310K
R3711
10KR37122SC4081UBTLQ
Q370410KR3714
33KR3720
OPENQ3706
UART1TX
0R3730
OPENR3772
10KR3715
2SC4081UBTLQQ3705
33KR3716
UART1RX
0R3717
Y3HDMI-CECT6STMCECPULT7HDMI0-SCL
39R313439R3137
W6HDMI0-SDAR9HDMI1-SCL
39R3139
AE3HDMI1-SDA39R3140
V7HDMI2-SCLAA5HDMI2-SDA
39R314139R3142
R7HDMI0-HPDU2HDMI1-HPDU6HDMI2-HPD
ARC-OUT
AA6HDMI1-5VAC3HDMI2-5V
AB5HDMIO-5V
Y6HDMI-UART-CTRL
OPENR3771
100R3179
10KR3002 1
C301282R3008 160
R3014
220PC3719
220PC3717
100KR3212
U5 PROTECT1STB-RESET
AA2 SP-MUTE
OPENC3107
OPENC3110
10KR3151
U1 KEY-IN1
MM5Z5V6BD3101
100R3107
1
2
3
4 5
6
7
8
IC3103M24C16-WMN6TP
A0
A1
A2
VSS SDA
SCL
WP
VCC
W3 BACKLIGHT-SW
39R3157
AB6 P-ON-H2
OPENC3122
BACKLIGHT-SW
10R3117
8P-ON+5V
0R3159
U3 REMOTE
P-ON-H2 2
4.7KR3152
T3 LIGHT-SENS
PROTECT3
U4 STM-EEPROM-WP
PROTECT3
SP-MUTE
P-ON+5V
C31270.1
AC1 STM-SDA
2SC4081UBTLQQ3101
0.1C3111
OPENR3110
1KR3102
2SCL(NU) V3 LED1
5REMOTE
33R3323
100R3133
P-ON+3.3V
39R3156
Y2 P-ON-H2
OPENR3114
1C3108
6LED1
22R3158
AD5 STB-RESET
HP-MUTE
100R3161
100KR3146
100R3160
10KR3106
4KEY-IN1
10KR3103
PROTECT1
OPENC3123
CN31051SDA(NU)
7LIGHT
3GND
P-ON-H2
2SC4081UBTLQQ3102
27KR3104
CN3103AL+3.3V 1
AC2 STM-SCL
9AL+3.3V
T2 PROTECT3
OPENC3112
4.7KR3153
100R3105
OPENR3119
C310633/10V OPEN
R3182
0.1C3101
22KR3096
1KR3131
W7 HP-MUTE
OPENR3138
OPENQ3103
OPENR3120
OPENR3143
W4 LED2
W5 STMTIME1
OPENR3207
OPENR3188
Y5 SW-EN
AA4 NUY1 NUAB1 NUAB3 NUAB2 NUY4 NUV6 NUAA3 NUV4 NU
10KR3109
Y7VGA-SCLAD3VGA-SDAU7NU
39R316539R3178
VGA-SDAVGA-SCL
STB-RESETSTMTIME1
22R3162W2 LCD-P-ONLCD-P-ON
10KR3150
AL+3.3V
Q3107OPEN
OPENR3200
OPENR3209
0R3144
OPENQ3108
OPENR3215
OPENR3206
C3100220/6.3V
DIGITAL SIGNAL PROCESS/MAIN MICRO CONTROLLER
HDMII/F
HDMI-CONNECTOR-1
HDMI-CONNECTOR-3
HDMI-CONNECTOR-2
AQ
DIGITAL MAIN CBA UNIT
(SWITCHING)
(SWITCHING)
(SWITCHING)
CONTINUEDIGITAL 6
CONTINUEDIGITAL 5
2
4
1
3
AR AS AT AU AV
TO DIGITAL MAIN 6IC3101(5/7)
VIDEODECODER
AUDIODECODER
TO DIGITAL MAIN 6IC3101(5/7)
(SWITCHING)
(SWITCHING)
(MEMORY)
CONTINUEDIGITAL 7
(NO CONNECTION)
(LED DRIVE)
CONTINUEDIGITAL 7
CONTINUEDIGITAL 6
CONTINUEDIGITAL 4
CONTINUEDIGITAL 6
CONTINUEDIGITAL 2
(BUFFER)
TO IR SENSORCBA UNIT CN4052
Digital Main 8 Schematic Diagram [TYPE A]
PL13.14ASCD8
The order of pins shown in this diagram is different from that of actual IC3101. IC3101 is divided into seven and shown as IC3101 (1/7) ~ IC3101 (7/7) in this Digital Main Schematic Diagram Section.
1 NOTE:
10-15
OPENR3045
OPENR3044 OPEN
R3047OPENR3046
OPENC3057
P-ON+21V
VCOM-PWM
P-ON+3.3V
CELL-PWR-CTRL
OPENC3058
1
2
3
4 5
6
7
8
IC3201MP1472GJC452Z
SS
EN
COMP
FB GND
SW
IN
BST
0.1C3202
D3203OPEN 4.7
C3213OPENC3210
4.7C3211
OPENR3218
4.7C3205
4.7C3212
10KR3216
L320133uH
0.1C3208
OPENC3209
OPENC3207
4.7C3214
0.015C3201
1KR3213
OPENC3204
1KR3208
120KR3209
10KR3205
OPEND3201
OPENR3211
D3202OPEN
PROTECT3
1SS400D3204
OPENC3000
OPENR3048
3 LCD+12V
48 NU
11 NU12 NU
6 GND
9 NU
5 NU
50 NU(SDA)
47 NU
7 GND
49 NU(SCL)
8 GND
CN30131 LCD+12V
10 NU
43 NU
4 LCD+12V
42 NU
2 LCD+12V
41 GND
44 NU45 SELLVDS
51 NU(GND)
46 NU
OPENR3165
0R3130
OPENR3171
OPENR3170
OPENC3167
OPENC3166
OPENQ3007
OPENR3166OPENR3167
4 NU(SCL)
2 NU(GND)
CN30051 GND
3 NU(SDA)
OPENR3173
1000PC3171
4.7C3170
0R3172
OPENR3129
0R3099
OPENR3253OPENR3254
0R3251OPENR3252
OPENR3168
OPENR3169
OPENR3174
1000PC3203
24KR3202
100PC3235
OPENC3206OPENR3215
OPENR3291
OPENR3217
OPENR3289
Q3282OPEN
1
2
3 6
7
8
4 5
OPENC3282
OPENR3283
OPENC3258
OPENC3257
Q3201OPEN
G
S D
OPENR3085
116
118
103
113
107
119
99
121
100
114
112
117
97
104
105
120
115
101
122
123
102
106
108
3PC3682
3PC3674
3PC3662
3PC3661
3PC3666
OPEN
C3671
3PC3667
3PC3670
OPEN
C3672
3PC3677
OPEN
C3683
3PC3668
OPEN
C3684
3PC3676
3PC3664
3PC3669
3PC3673
3PC3681
3PC3663
3PC3665
3PC3679
3PC3675
3PC3680
3PC3678
0R3145
0R3143
0R3142
0R3141
0R3140
0R3139
0R3137
0R3111
0R3110
0R3109
OPENR3248
OPENR3249
OPENR3149
OPENR3153
P-ON+5V
OPENR3284
OPENQ3202
OPENR3282
OPENC3256
OPENR3281
OPENQ3281
OPENC3281
OPENR3288
OPENR3287
OPENR3286
P-ON-H2
LVDS-OD0(+)
LVDS-OD3(+)
LVDS-OD2(-)
LVDS-OD3(-)
LVDS-OD1(-)
LVDS-OD0(-)
LVDS-OD2(+)
LVDS-OCLK(+)
LVDS-OD1(+)
LVDS-OCLK(-)
98
*1IC3001(1/5)MSD8200DS-S1
PANEL-VCOM-PWMCELL-PWR-CTRLLCD+12V
16 LVDS-OCLK(+)
30 LVDS-ED3(-)29 LVDS-ED3(+)
39 LVDS-ED0(+)
33 LVDS-ECLK(-)
35 LVDS-ED2(+)
19 LVDS-OD2(+)
15 GND
37 LVDS-ED1(+)
34 GND
32 LVDS-ECLK(+)
25 NU26 NU27 NU28 NU
24 LVDS-OD0(-)
38 LVDS-ED1(-)
18 GND
22 LVDS-OD1(-)
40 LVDS-ED0(-)
21 LVDS-OD1(+)
31 GND
14 LVDS-OD3(-)
23 LVDS-OD0(+)
36 LVDS-ED2(-)
20 LVDS-OD2(-)
17 LVDS-OCLK(-)
13 LVDS-OD3(+)
DIGITAL MAIN CBA UNIT
CONTINUEDIGITAL 3
(+12V REG.)
(NO CONNECTION)
DIGITAL SIGNAL PROCESS/MAIN MICRO CONTROLLER
TO DIGITAL MAIN 4IC3001(3/5)
LVDSTX
TO LCD PANELASSEMBLY
CONTINUEDIGITAL 5
CONTINUEDIGITAL 2
A
2
4
1
3
B C D E F
CONTINUEDIGITAL 2
Digital Main 1 Schematic Diagram [TYPE B]
PL13.14BSCD1
The order of pins shown in this diagram is different from that of actual IC3001. IC3001 is divided into five and shown as IC3001 (1/5) ~ IC3001 (5/5) in this Digital Main Schematic Diagram Section.
1 NOTE:
10-16
LVDS-OCLK(-)
LVDS-OD0(+)
LVDS-OD3(+)
LVDS-OD2(-)
LVDS-OD0(-)
LVDS-OD2(+)
LVDS-OD1(+)
LVDS-OCLK(+)LVDS-OD3(-)
LVDS-OD1(-)
OPENR3931
OPENR3932
OPENR3933
OPENR3934
OPENR3935
4 CPV
17 GND
11 LLV4(+)
8 LLV5(-)
28 GND
26 PWR-CTRL
12 LLV3(-)
1 STV
10 LLV4(-)
13 LLV3(+)
22 LLV0(-)
29 LCD+12V
2 OE2
23 LLV0(+)
16 LLVCNK(+)
21 LLV1(+)
15 LLVCLK(-)
30 LCD+12V
CN300131 LCD+12V
20 LLV1(-)
18 LLV2(-)19 LLV2(+)
3 OE1
9 LLV5(+)
24 GND
5 POL6 TP
14 GND
7 GND
25 P-ON+3.3V
27 VCOM-PWM
14 GND
10 LLV4(-)
17 GND
22 LLV0(-)
20 LLV1(-)
13 LLV3(+)
7 GND
21 LLV1(+)
19 LLV2(+)
5 POL4 CPV
18 LLV2(-)
23 LLV0(+)
9 LLV5(+)
12 LLV3(-)
29 LCD+12V
15 LLVCLK(-)16 LLVCNK(+)
2 OE23 OE1
28 GND
11 LLV4(+)
26 PWR-CTRL
8 LLV5(-)
1 STV
24 GND
27 VCOM-PWM
25 P-ON+3.3V
6 TP
CN300630 LCD+12V
LCD+12V
OPENC3513
OPENC3514
OPENR3037
OPENR3038
OPENR3035
CELL-PWR-CTRLPANEL-VCOM-PWM
OPENR3039
OPENC3512
OPENR3910
OPENR3908
OPENR3911
OPENR3914OPENR3912OPENR3909
OPEN
R311
7
OPEN
C316
1OP
ENC3
162
OPEN
C316
3OP
ENC3
164
OPEN
C310
2OP
ENC3
165
OPEN
R311
8OP
ENR3
119
OPEN
R312
0OP
ENR3
132
OPEN
R304
1
OPENR3904
OPENC3902
OPENR3906
OPENR3926
OPENC3923
OPENC3924
OPENC3919
OPENC3921
OPENC3916
OPENC3918
OPENC3914
OPENC3915
OPENR3927
OPENR3925
OPENR3921
OPENR3922
OPENR3928
OPENC3920
VDDC+1.26VL3901OPENC3913
OPEN
OPENR3924
OPENR3923
OPENR3913
OPENR3907
OPENC3922
OPENC3925
BACKLIGHT-DIMBACKLIGHT-ADJ
OPENR3916OPEN
OPENR3919
D3905OPEN
OPENR3920OPEN
C3917
OPENR3917
OPEN
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
21 22 24 25 26 27 28 2923 30 31 32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49505152535455565758596061626364
20191817
DATAINPUTLATCH
LVDSOUTPUT
DATA PROCESSING
LVDSRX
CONTROL SIGNAL GENERATOR
SERIALI/F
IC3902OPEN
VDD-LVDS
GND
VDDC(1.2V)
RESET
GND
LV-SEL
PWMO
/GP0
6
VDDC
(1.2
V)
NU NU VDDP
(3.3
V)
NU NU UD-S
EL/G
P02
KB/G
P01
VDDP
(3.3
V)
GND
GND
VDDP
(3.3
V)
REL
VDDP
(3.3
V)NUNUGND
GND
VDDC
(1.2
V)
MGD-
EN/G
P08
VDDP
(3.3
V)NUOD
-EN/
GP08
VDDP
(3.3
V)
TSET
P-ON+3.3V
OPENR3028
4
1
3
2
JI LG H K
DIGITAL MAIN CBA UNIT
CONTINUEDIGITAL 1
(NO CONNECTION)
(NO CONNECTION)
CONTINUEDIGITAL 5
CONTINUEDIGITAL 5
CONTINUEDIGITAL 1
Digital Main 2 Schematic Diagram [TYPE B]
PL13.14BSCD2
10-17
IC3002K4T51163QJ-BCE7
*A VDDJ2VREF
E2 NU
K2CKEJ8CKK8CKL8CSK7RASL7CASK3WEL1BA2/NUL3BA1L2BA0
R2A12P7A11M2A10/APP3A9P8A8P2A7N7A6N3A5N8A4N2A3M7A2M3A1M8A0K9ODT*BVSS
A2 NU
R8A13
R7 NUR3 NU
B7 UDQSA8 UDQS/NUB3 UDMB9 MDQU7
C2 MDQU1C8 MDQU0F7 LDQSE8 LDQS/NUF3 LDMF9 MDQL7F1 MDQL6H9 MDQL5H1 MDQL4H3 MDQL3H7 MDQL2G2 MDQL1G8 MDQL0
0.1C3222
1
2
3
4 5
6
7
8
IC3006W25Q32FVSSIG
CS
SO
WP
GND SDA
SCL
NU
VCC
0.1C32230.1C32240.1C32250.1C32260.1C32270.1C32280.1C32290.1C32180.1C32160.1C32200.1C32210.1C3215
4.7KR3102
0.1C3073
P-ON+3.3VAL+3.3V
DDR+1.8V
10C3219
D1 MDQU4D3 MDQU3D7 MDQU2
B1 MDQU6D9 MDQU5
1KR3232
1KR3231
OPENC3230OPENC3231OPENC3232OPENC3233OPENC3234
190 SD-A3
174 SD-A4
187 SD-A9
192 SD-CKE
176 SD-A8
169 SD-RAS
183 SD-A10
172 SD-A2
168 SD-ODT
170 SD-CAS
171 SD-A0
181 SD-BA0
188 SD-A12
179 SD-WE
191 SD-BA2
175 SD-A6
165 SD-CLKN
184 SD-A5
180 SD-BA1182 SD-A1
202 WP
177 SD-A11
164 SD-CLK
189 SD-A7
145 SD-UDM
161 MDQL2
144 MDQU6
139 MDQL6
138 MDQL1
152 SD-LDM
143 MDQU1154 MDQU0
142 MDQU4
153
MSD8200DS-S1
*1IC3001(2/5)
MDQU7
162 MDQL5
150 SD-UDQSN
158 MDQL7
136 MDQL4
149 SD-UDQS
157 MDQU5
155 MDQU2
148 SD-LDQSN
160 MDQL0
137 MDQL3
141 MDQU3
147 SD-LDQS
204 CS
199 SPI-SCL
201 SOUT200 SPI-SDA
75R3238
75R322175R322975R323775R3222
75R3235
75R3236
75R322775R3204
75R3203
75R322375R324075R3224
75R322575R3239
75R3226
56R3234
56R3233 0.01
C3217
R3220 75x4
R3228 75x4
178 SD-A1375R323033R3089
33R3154
33R3092
OPENR3194
10KR3107
33R3093
33R3094
0.033C3113
OPEND3108
1000PC3116
220R3178 56K
R3182
1C3106
RESET
32
1 4
IC3009PST8429UR
CDVDD
GND OUT
OPENC3252
OPEND3110
2SC4081UBTLQQ3104100
R3241
10KR3219
OPEND3109
OPENR3242
216 STB-RESET
OPENC3110
VCOM-PWMCELL-PWR-CTRL
OPENC3175
OPENR3150132I2S-OUT-MCK
OPENR3195
1KR3199
75BACKLIGHT-SW
OPENR3210
22R3106
129BACKLIGHT-ADJ
OPENQ3101 PROTECT1
206P-ON-H210R3101
10KR3191
PROTECT3134PROTECT3
BACKLIGHT-ADJ
OPENR3177
100R3161
10KR3196
209PROTECT1
10KR3193
P-ON-H2
2SA1576UBTLQQ3103
BACKLIGHT-SW
33KR3189
10KR3160
10KR3159
OPENQ3102OPEN
R3156
76CELL-PWR-CTRL
OPENR3155
83VCOM-PWM100R3188
10KR3163
X310124MHz
15PC3169
18PC3172
L310122uH
0.1C3121
51AUVRM
53AUVAG
52AUVRP
1C3133
10C3120
4.7C3123
66XOUT67XIN
160R3157
OPENR3158
BACKLIGHT-SWAMP-MUTE127AMP-MUTE
0R3355
OPENC3189
207NU1C3101
100R3162
33KR3197
P-ON-H2PROTECT3
DIGITAL MAIN CBA UNIT
DIGITAL SIGNAL PROCESS/MAIN MICRO CONTROLLER
(DDR2 SDRAM)
*B:A3,A7,B2,B8,D2,D8,E3,E7, F2,F8,H2,H8,J3,J7,N1,P9
*A:A1,A9,C1,C3,C7,C9,E1,E9, G1,G3,G7,G9,J1,J9,M9,R1
1-O32-O33-O3
4-O35-O36-O3
MDQU7
MDQU1MDQU0
MDQL7
1-M32-M3
3-M3
4-M35-M3
6-M3
(MEMORY)
CONTINUEDIGITAL 5
2
M P
1
N O
3
4
Q R
TO DIGITAL MAIN 4IC3001(3/5)
MDQU3MDQU2
MDQU6MDQU5MDQU4
MDQL6MDQL5MDQL4MDQL3MDQL2MDQL1MDQL0
MDQU7
MDQU1MDQU0
MDQU3MDQU2
MDQU6MDQU5MDQU4
MDQL7MDQL6MDQL5MDQL4MDQL3MDQL2MDQL1MDQL0
(RESET)
(SWITCHING)
CONTINUEDIGITAL 1
TO DIGITAL MAIN 4IC3001(3/5)
CONTINUEDIGITAL 5
CONTINUEDIGITAL 4
(SWITCHING)
Digital Main 3 Schematic Diagram [TYPE B]
PL13.14BSCD3
The order of pins shown in this diagram is different from that of actual IC3001. IC3001 is divided into five and shown as IC3001 (1/5) ~ IC3001 (5/5) in this Digital Main Schematic Diagram Section.
1 NOTE:
10-18
SP3801SPEAKERL-CH
3 SP(R)-2 SP(L)-
4 SP(R)+
CN38011 SP(L)+
AMP-MUTE
AL+3.3VP-ON+5VAMP+13V
HEADPHONEJACK
JK3703
P-ON+3.3V
1
2
3
4
27
28
26
25
22
24
23
21
6
5
8
7
10
11
12
9
13
14
18
20
15
19
16
17
CONTROLLOGIC
AVCC
POWERLIMIT
PWMLOGIC DRIVE
GAINCONTROL
DRIVE
DRIVE
POWERLIMIT
PWMLOGIC DRIVE
GND
GVDD
NU
PBTL PVCCR
PVCCR
GND
GND
PVCCL
PVCCL
IC3801TPA3110D2PWPR
1KR3704
1C3704
BACKLIGHT-SW
0.22C3801
OPEND3801
OPENC3820
1000PC3811
L380110uH
OPENR3801
OPENC3807
OPENC3808
1000PC3812
L380210uH
OPENR3802
OPEND3802
1C3821
OPENC3822
OPEND3803
1000PC3813
L380310uH
OPENC3809OPENR3803
OPEND3804
1000PC3814
OPENR3804
OPENC3810
1C3823
L380410uH
0.22C3802
0.22C3803
0.22C38041C3806
1C3805
1C3819
10KR3808
1C3816
1C3817
OPENR3807
0R3806
OPENR3805
1C3818
2SC4081UBTLQQ380110K
R3812
10R3820
OPENR3818
10KR3814 Q3803
OPEN
OPENQ3802
OPENR3817
OPENR3816
10KR3811
OPENR3821
0R3813
10KR3809
OPENR3810
10C3832
0.047C3827
2.2C3828
220/16VC3831
100/16VC3829
SP3802SPEAKERR-CH
OPENC3836
1C3837
OPENC3838
OPENC3839
OPENC3841
1C3842
OPENC3843
OPENC3844
10C3833
0.047C3824
2.2C3825
D38061SS400
D38051SS400
10KR3705
1C3815
100KR3815
OPENR3819
0.1C3830
0R3725220/6.3V
C3705
OPENR3718
OPENR3701
OPENC3711
0R3716
0.01C3721
L370110uH
OPEND3702
OPEND3707
OPEND3706
OPEND3701
1KR3702
L370210uH
0.01C3722
OPENC3712
OPENR3719
0R3724
0R3717
OPENR3703
220/6.3VC3710
OPEND3703
OPEND3708
OPENQ3703
OPENR3722
OPENR3723
OPENR3721
OPENR3720 OPEN
Q3702
OPENC3723
OPENC3724
D3704OPEN
OPENR3726
75R3126
R3136 33
10KR3712
220R3709
10PC3701
10PC3702
330PC3720
R3123 0
D330
21S
S400
12KR3713
1
2
3
4
5
14
13
12
11
15
6
7
8
9
10
JK3001PC-RGB-IN
75R3146
100R3708
100PC3709
JK3702
4.7K
R332
6
2.2C3126
75R3148
1C3707
100PC3188
R3144 33
4.7K
R332
1
0.1C3708
75R3147
2.2C3125
7.5KR3711
330PC3719
10PC3703
2SC4081UBTLQQ3701
R3122 331C3706
75R3127
JK3701
75R3125
D33011SS400
100R3710
OPEN
C301
5
10P
C300
9
D305
5OP
END3
045
OPEN
D305
0OP
EN
D305
3OP
END3
049
OPEN
0.047C31180.047C3139
0.047C3136
1000PC3119
10P
C300
7
OPEN
C301
6
R3131 0 1000PC313728
10P
C300
2
OPEN
C301
7
27
0R3016
OPENC3018
300.047C3117R3121 68
310.047C3134R3134 33
10K
R334
7
R3339 100
26 VGA-HSYNC
10K
R335
8
R3343 100
10P
C302
0OP
ENC3
014
32 VGA-VSYNC
D305
4OP
END3
041
OPEN
38
3534
0.047C314033R313836
COMP-DET133
IC3001(3/5)*1
MSD8200DS-S1
NU3768R3124 0.047C3141
0R3715
OPENC3715
OPENC3716
R3198 100130 SPDIF
10KR3706
560PC3718
47
560PC3713
10KR3707
12KR3714
48
OPENC3714
OPENC3717
6160
220K
R316
433
0PC3
147
220K
R317
533
0PC3
148
6364
10KR3200
1
2
3 4
5
IC3019AP2151WG-7
OUT
GND
/FLAG RN
IN
80VBUS-ST
10KR3479
1C3327
22R317682VBUS-EN
2 USB(-)
4 GND3 USB(+)
CN3009 (USB JACK)1 BUS-POWER
220/6.3VC3348
1C3246
OPEND3052
195USB(+)5.1R30205.1R3021
194USB(-)
2UART0-TX
CN30101P-ON+5V
3UART0-RX4GND
OPENC3254
OPENC3255
OPENR3395
OPENR3396
OPEN
C301
310
PC3
019
100R3015
100R3014
OPENC3253
213 VGA-SDA212 VGA-SCL
100R3114100R3115
UARTTXD0UARTRXD0
0.047C312468R3128NU45
10KR3480
R3354 33
0.047C313529
R3135 33
DIGITAL MAIN CBA UNIT
(AUDIO AMP)
(SWITCHING)
W X
2
4
1
VS
3
T U
DIGITAL SIGNAL PROCESS/MAIN MICRO CONTROLLER
DIGITAL AUDIO OUT(COAXIAL)
AUDIO(R)-IN
SW
COMPONENT-Pr-IN
AUDIOI/F
TO DIGITAL MAIN 6IC3001(5/5)
AUDIO(L)-IN
(BUFFER)
COMPONENT-Pb-IN
COMPONENT-Y/VIDEO-IN
DIGITALSIGNALPROCESS
TO DIGITAL MAIN 1IC3001(1/5)
A/DCONVERTER
(HIGH SIDE SW)
(NO CONNECTION)TO DIGITAL MAIN 6IC3001(5/5)
TO DIGITAL MAIN 6IC3001(5/5)
TO DIGITAL MAIN 6IC3001(5/5)
TO DIGITAL MAIN 3IC3001(2/5)
TO DIGITAL MAIN 3IC3001(2/5)
CONTINUEDIGITAL 5
CONTINUEDIGITAL 6
CONTINUEDIGITAL 3
Digital Main 4 Schematic Diagram [TYPE B]
PL13.14BSCD4
The order of pins shown in this diagram is different from that of actual IC3001. IC3001 is divided into five and shown as IC3001 (1/5) ~ IC3001 (5/5) in this Digital Main Schematic Diagram Section.
1 NOTE:
10-19
6P-ON-H2
CN36011LED-CONT(NU)
17AMP+13V
2PROTECT1
10GND
7BACKLIGHT-ADJ
11GND
15AMP+13V14GND
21P-ON+21V
8AL+3.3V
22P-ON+21V
18AMP+13V
3PROTECT3
13GND
4RESET
23P-ON+21V
9GND
16AMP+13V
20P-ON+21V
12GND
5BACKLIGHT-SW
19GND
19BACKLIGHT-SW
21PROTECT3
8AMP+13V
2P-ON+21V
14GND
22PROTECT1
1P-ON+21V
4P-ON+21V
9AMP+13V
20RESET
3P-ON+21V
18P-ON-H2
12GND
CN360223LED-CONT(NU)
15GND
13GND
11GND
7AMP+13V
5GND
17BACKLIGHT-ADJ
10GND
16AL+3.3V
6AMP+13V
P-ON+5VP-ON+3.3VP-ON21V
10C3623
1
2
3
4 5
6
7
8
IC3604RT8293ALZSP
BS
VIN
SW
GND FB
COMP
EN
SS
OPENR3628
L360210uH
0.1C3618
OPENC3616
0.22C3617
5.1KR3603
C362110
OPENC3643
C3620220/6.3V
0.1C3652
OPENC3638
20KR3615
4700PC3619
0.01C3615
10KR3614
33KR3616
D3608OPEN
Q36012SC4081UBTLQ
20KR3621
1KR3620
OPENC3641
D36091SS400
OPENC3656
0.1C3655
OPENC3657
2SA1576UBTLQQ3005
22KR3008
Q30062SC4081UBTLQ
1C3011
100KR3005
56KR3097
D30121SS400
OPENR3100
100KR3007
10KR3098
OPENC3010
47KR3618
D3011MM5Z7V5B
OPENR3133
OPENC3630
1
2
3
4 5
6
7
8
IC3605RT8293ALZSP
BS
VIN
SW
GND FB
COMP
EN
SS
C363510
2KR3619
100R3647
OPENR3627
10KR3641
10C3622
1C3633
0.01C3629
8.2KR3625
0.1C3601
L360310uH
0.01C3626
10C3634
1KR3626
4.7C3637
OPENC3642
Q36032SC4081UBTLQ
2SA1576UBTLQQ3602
0.1C3628
100R3642
0.047C3627
16KR3624
D3606PTZTE255.1B
10KR3644
C3632220/6.3V
OPENC3686
47KR3643
10KR3645
1
2
3
4 5
6
7
8
IC3603BD00IA5WEFJ-E2
VOUT
FB
GND
NU EN
NU
NU
VCC
10C3610
11KR3613
2.2KR361112KR3612
10C3613 OPEN
R3646OPENC3687
1R3661
10KR3601
10C3608
100R3606
220/6.3VC3605
10C3614
220R3604
1 2 3
IC3602AP1117EG-13
VOUT
VIN
COM
33R3605
10C3612
220/6.3VC3602
0R3608
1 2 3
IC3601AP1117EG-13
VOUT
VIN
COM
120R3609
120R3610
180R3607
D36031SS400
D36011SS400
10C3636
OPENR3623
22KR3656
22KR3651
2SC4081UBTLQQ3606
2SA1576UBTLQQ3605
10KR3655
10R3654
10KR3652
1KR3653
OPENR3638
OPENC3604
OPENC3647
OPENC3646
OPENC3645
0.1C3648
OPENC3649
OPENC3603
10C3660
D3602OPEN OPEN
C3644
OPENC3640
OPENC3624
OPENC3625
4.7C3639
4.7C3607
D3610MM5Z4V3B1
C3659 D3611OPENOPEN
C3658
12 AVDD-DVI90 AVDD-DVI-PC203 AVDD-ALIVE
L31100
10C3103
0.1C3132
0.1C3160
0.1C3114
40 AVDD-CVBS
0.1C3130
0.1C3158
L31120
59 AVDD-AU33
0.1C3159
L31140
68 AVDD-DMPLL
0.1C3157
L31130
65 AVDD-EAR33
25 VDDC
0.1C3127 33 AVDDL-ADC0.1
C3131
84 VDDC0.1C3151
111 AVDDL-MOD
0.1C3185
124 VDDC0.1C3176
156 DVDD-DDR0.1C3186
193 VDDC
0.1C3107
39 AVDD-ADC25
0.1C3129
0.1C3128
L310322uH
54 AVDD-AU25
L310222uH
0.1C3154
L310722uH
69 AVDD-ADC25
L310522uH
72 AVDD-PGA25
0.1C3152
73 PGA-COML310622uH
0.1C3184
110 AVDD-MOD
81 VDDP
10C3155
0.1C3156
L31160
109 AVDD-LPLL
0.1C3181
128 VDDP0.1C3183
10C3182
L31150
166 AVDD-PLL
0.1C3112
140
MSD8200DS-S1
*1IC3001(4/5)
AVDD-DDR-DATA
0.1C3180
0.1C3178
0.1C3179
0.1C3108
0.1C3177 146 AVDD-DDR-DATA
151 AVDD-DDR-DATA
0.1C3111
0.1C3109
159 AVDD-DDR-DATA163 AVDD-DDR-DATA173 AVDD-DDR-CMD186 AVDD-DDR-CMD
C3611220/6.3V
AL+3.3V(1)
62 GND77 GND198 GND
L31110
L310922uH
P-ON+5VP-ON+3.3VAL+3.3V
AMP+13VP-ON+5VAL+3.3V
P-ON+3.3V
OPENC3651
VDDC+1.26VP-ON+3.3V
DDR+1.8VP-ON+3.3VAL+3.3V
PROTECT3
RESET
BACKLIGHT-ADJ
PROTECT1
BACKLIGHT-ADJ
BACKLIGHT-SW
BACKLIGHT-DIM
P-ON-H2
100R3633
100R3631100R3632
OPENR3629
OPENC3650D3607
OPEN
OPENR3637
270R3635
OPENC3653
10C3609
1R3662
57NU58NU167NU185NU196NU197NU
43NU44NU46NU
55NU50NU
42NU
56NU
49NU
41NU
2KR3108
DIGITAL MAIN CBA UNIT
TO POWER SUPPLYCBA CN501
(NO CONNECTION)
(+5V REG.)
(SWITCHING)
(SWITCHING)
(SWITCHING)
(+1.26V REG.)
(+1.8V REG.)
(+3.3V REG.)
(+2.5V REG.)
(SWITCHING)
Z
4
AA ADACABY
2
1
3
DIGITAL SIGNAL PROCESS/MAIN MICRO CONTROLLER
CONTINUEDIGITAL 1
CONTINUEDIGITAL 6
CONTINUEDIGITAL 4
CONTINUEDIGITAL 2
CONTINUEDIGITAL 3
CONTINUEDIGITAL 3
CONTINUEDIGITAL 2
(SWITCHING)
(SWITCHING)
(SWITCHING)
Digital Main 5 Schematic Diagram [TYPE B]
PL13.14BSCD5
The order of pins shown in this diagram is different from that of actual IC3001. IC3001 is divided into five and shown as IC3001 (1/5) ~ IC3001 (5/5) in this Digital Main Schematic Diagram Section.
1 NOTE:
10-20
10KR3275
10KR3278
10KR3212
10KR3214
10KR3001
10KR3003
16 HDMI-DATA
12 CLOCK(-)
JK30041 DATA2(+)
6 DATA1(-)
3 DATA2(-)
14 ARC
9 DATA0(-)10 CLOCK(+)
7 DATA0(+)
5 TMDS DATA1 SHIELD
17 GND18 +5V
13 HDMI-CEC
15 HDMI-CLOCK
19 HOT PLUG DETECT
2 TMDS DATA2 SHIELD
4 DATA1(+)
11 TMDS CLOCK SHIELD
8 TMDS DATA0 SHIELD
16 HDMI-DATA
12 CLOCK(-)
JK30031 DATA2(+)
6 DATA1(-)
3 DATA2(-)
14 NU
9 DATA0(-)10 CLOCK(+)
7 DATA0(+)
5 TMDS DATA1 SHIELD
17 GND18 +5V
13 HDMI-CEC
15 HDMI-CLOCK
19 HOT PLUG DETECT
2 TMDS DATA2 SHIELD
4 DATA1(+)
11 TMDS CLOCK SHIELD
8 TMDS DATA0 SHIELD
14 NU
17 GND
19 HOT-PLUG-DETECT
15 HDMI-CLOCK
18 HDMI+5V
16 HDMI-DATA
2 TMDS DATA2 SHIELD
10 CLOCK(+)
JK30021 DATA2(+)
4 DATA1(+)
7 DATA0(+)
5 TMDS DATA1 SHIELD
8 TMDS DATA0 SHIELD
11 TMDS CLOCK SHIELD
3 DATA2(-)
13 HDMI-CEC
6 DATA1(-)
12 CLOCK(-)
9 DATA0(-)
2SC4081UBTLQQ34071K
R3421
1KR3420
OPENR3423
47KR3422
1KR3010
OPENR3017
2SC4081UBTLQQ30011K
R3018
47KR3019
OPENR3058
1KR3055
2SC4081UBTLQQ30081K
R3063
47KR3066
2SC4081UBTLQQ300210K
R3071
33KR30762SA1576UBTLQ
Q3004
OPENR3077
10KR3079
100R3407100R3406
100R3042100R3050
100R3022100R3023
100R3113
P-ON+5VP-ON+3.3VAL+3.3V
2221191816151413
11
3
10
4
2
578
95
86
91
94
87
8988
92
85HDMI3-HPD
96
2023
6
214HDMI-CEC
93
1HDMI2-HPD17HDMI1-HPD
9
0R34250R34260R34270R34280R34290R34300R34310R3432
0.1C3404D3004
RB751S-40D3005RB751S-40
0R30570R3062
0R30640R3065
0R3056
0R30670R3069
0R3070
0.1C3005D3006
RB751S-40D3007RB751S-40
0R3026
0R3027
0R3036
0R3029
0R3034
0R3024
0R3025
0R3040
0.1C3023D3008
RB751S-40D3009RB751S-40
2SC4081UBTLQQ3011
100R3081
1KR3078
2SC4081UBTLQQ3003
33KR3074
10KR3073
330PC3003
1KR3075
10KR3080
OPENR3243
OPENR3244
OPENR3245
OPENC3556
OPENC3557
22R3105
4KEY-IN1
33PC3551
OPENR3558
100R3552
39KR3186
9AL+3.3V
7LIGHT
22R3103
10R3557
8P-ON+5V
210 KEY-IN1
OPENC3559
10KR3185
215 REMOTE205 LED1
100R3183
OPENC3115
MM5Z5V6BD3501
6LED1
OPENR3503
100R3551
1C3554
OPENC3555
5REMOTE
4.7KR3502
CN31011SDA(NU)
10R3556
78 SCL79 SDA
100KR3560
OPENC3553
10C3558
Q35022SA1576UBTLQ
33PC355210KR3184
OPENR3555
2SC4081UBTLQQ3010
2SCL(NU)
10KR3559
10KR3112100
R3553
4.7KR3501
2SC4081UBTLQQ3501
4.7KR3116
OPENC3191
208 LIGHT
3GND
131 FACTORY-SEL100R3201
UARTTXD0UARTRXD0
C3550OPEN
OPENR3535
Q3531OPEN0
R3536
10KR3192
OPENR3534
0R3353
135 SW-EN
OPENC3187
33PC3908D3901
MM5Z5V6B
L3913OPEN
D3904MM5Z5V6B
TU3901 (TUNER UNIT)
1
+3.3
V
2
GND
3
SDA
4
SCL
5
IF-A
GC
6
DIF-
OUT1
7
DIF-
OUT2
4.7KR3937OPEN
C393410C3905
4.7KR3938D3903
MM5Z5V6B
33PC3909
0.022C3168
0.1C3910
D3902MM5Z5V6B
OPENC3901
OPENC3904
OPENC3906
47R3206
47R3207
100R3936
TU-SDA125TU-SCL126
0R3179
10KR3180
10C3149
74 IF-AGC
L310422uH
33PC3927
33PC3926
0.1C3174
0.1C3173
33R3151
33R3152
OPENC3145 L3108
OPEN
OPENC3144
OPENC3150
70
71
IC3001(5/5)MSD8200DS-S1
*1
51R3181 0.1
C3142
0.1C3143
51R3187
1 2 3
IC3901AP1117EG-13
VOUT
VIN
COM
100R3903
33R3902
220R3901
10C3911
220/6.3VC3907
OPENC3912
24HDMI-ARC
OPENC3012
OPENR3082
AL+3.3V(1)
10KR3417
22R3104
211 WAKE
10R3822
DIGITAL SIGNAL PROCESS/MAIN MICRO CONTROLLER
HDMII/F
HDMI-CONNECTOR-3
HDMI-CONNECTOR-1
HDMI-CONNECTOR-2
AE
DIGITAL MAIN CBA UNIT
(SWITCHING)
(SWITCHING)
(SWITCHING)
2
4
1
3
AF AG AH AI AJ
TO DIGITAL MAIN 4IC3001(3/5)
VIDEODECODER
AUDIODECODER
(SWITCHING)
CONTINUEDIGITAL 5
(SWITCHING)
(SWITCHING)
(SWITCHING)
(LED DRIVE)
(BUFFER)
(LED DRIVE)
DEMODULATOR/MPEGDECODER
(+3.3V REG.)
TO DIGITAL MAIN 4IC3001(3/5)
TO DIGITAL MAIN 4IC3001(3/5)
TO DIGITAL MAIN 4IC3001(3/5)
CONTINUEDIGITAL 4
TO IR SENSOR CBA UNIT CN4052
Digital Main 6 Schematic Diagram [TYPE B]
PL13.14BSCD6
The order of pins shown in this diagram is different from that of actual IC3001. IC3001 is divided into five and shown as IC3001 (1/5) ~ IC3001 (5/5) in this Digital Main Schematic Diagram Section.
1 NOTE:
10-21
CN501
IC1702IC1703
D654
D704
BA3AU0F0102 3
J182
J184
J177
J183
J187
GND
GND P-ON+21V
AMP+13V
GND
C692
J179
Q691
__Ba
se
J190 GND
J151 C651
ALL+
3.3V
RISK OF FIRE -
REPLACE FUSE AS MARKED
CAUTION -
HOT
COLD
UNDE
R SI
DE
__LIVE
__NEUTRAL
PROT
ECT1
P-ON
+21V
IC601 __Vcc
IC604 __Ref
C619
C606
CN60
1
R601
C620
C616
C615
Q601
BC60
2
T601D651
556C456C D655
D653
Q1601
C1614
C605D1605
IC602IC603
R679
D660
IC60
4
Q657
C650
R678
R676
C656
R618
J168
J163
J189
J162
J170
J186
T1601
J185
J176
GND
PFC__
GND
DRIV
E
P-ON
__H2
C665
J175GND
J173
J174
AMP+
13V
C662
C663
GP00
3
J150
ZCDB
IC60
1__
FB
J154
J149
VIN
VIN
PFC __GND
J164
D656
__Ca
thod
e
PFC __GND
J167
IC60
1__
FB
BC16
03
BC60
3
D619A
D620
AD6
21A
HOT
D613
C604
L602
C614
R162
4
C161
2
C161
5
CN1001 D602
D601
D604
D603
C601
D607
C602R6
02JS
601
D605 L601
T1602
J121
PFC__
VIN
VIN
54
L601A
L602
A
BC1601
BC1602
C1626J1
35PF
C__
J136
PFC__
JS60
2VI
N
J132 PFC __GND
F602
T 2.5A L/250V
D606
SA601
D609A
COLD
Q120
2__
Gate
GATE
IC13
01
Q1302 __Gate C1707
C1305
J126
J103
J123
J111
BL-S
W
GND
IC13
01_G
ATE
J120
PFC__
VIN
GND
J156J157
J119
PRI__
D1307 __Cathode
32
BC13
01
J108
GND
GND
J114 J113
J104GND
J105
AMP+
13V
Oute
r__
GND
J193
D1302
R131
5
8765 109
__CS
L130
1
C1621C1
613
Q1602
C162
2
C1301
J138
J134
J147
J146
J109
J143
J129
PRI__
GND
PFC __VOUT
PFC __VOUT
PFC __VOUT
Prot
ect3 GN
D
GND
GND
J124
J122
BC13
02
BC16
04
GND
IC1201 __
Q1101 __Source
BL-A
DJ GND
J131
J137
J128
J106
J107
J118
GND
AMP+
13V
BL-S
W
J125
J127
J116
BL-S
W
J133
GND
J117
AMP+
13V
J178
C1101
D1102
C1205
C1105
GND
Prot
ect3
GP001
1
BA
BC12
01
BC11
01R1
115
GND
L1101
L1201
BC12
02
BC11
02
J115
Q110
2__
Gate
J101 GND
J181
Protect3
D120
2
R121
5
4321TOOL NO.
COLD
HOT
PFC__
GND
GDA
Q1608 __Collector
IC1601 __Vcc
PFC__
GND
IC16
01__
Vref
IC16
01__
Vcc
Q170
4__
SOUR
CE
C1602
D650
C652
D1603
C1623
Q1704
C1708
C723
IC16
02IC
1603
BC17
03
C1706
C725
D1707
C1201
J169
J142
J165
J152
J140
J153
PRI__
GND
GND
C1709J1
59
J171
PFC __GND
J166
C161
8
R1719
C726
C1001
J161
PFC__
VOUT
J148 GDA
J158
IC16
01__
Vcc
J160
J110
J102
J130
PFC __VOUT
D714A
TOP
SIDE
Protect3LED__
Vin
C724
D712
D711
D710
J172
J144Prot
ect3
BL-ADJ
J141
J145
C
J155 GND
D713
J191
J180
Oute
r__
GND
Outer __GND
GP002
D
T1701
BA3AU0F01023
Power Supply CBA Top ViewBecause a hot chassis ground is present in the power supply circuit, an isolation transformer must be used when repairing.Also, in order to have the ability to increase the input slowly, when troubleshooting this type of power supply circuit, a variable isolation transformer is required.
NOTE:The voltage for parts in hot circuit is measured using hot GND as a common terminal.
CAUTION !Fixed voltage (or Auto voltage selectable) power supply circuit is used in this unit. If Main Fuse (F602) is blown , check to see that all components in the power supply circuit are not defective before you connect the AC plug to the AC power supply. Otherwise it may cause some components in the power supply circuit to fail.
For continued protection against risk of fire, replace only with same type 2.5A, 250V fuse.
CAUTION ! :
ATTENTION : Utiliser un fusible de rechange de même type de 2.5A, 250V.2.5A 250V
10-22
CN601
R601
IC604
PFC__
GND
J164
__GND
R629
Q603
R628C621
C611C622
R613
R627
R620R623
C624R632
R633
D614D623
C1621C724
C1301
C1305
C1201
J131
J138
J137
J134
J142
J172J144J140
J146
J128
J126
J106
J107
J118
J109
J129
J103J123
J111
BL-SW
PFC__VOUT
PFC__VOUT
Protect3
BL-ADJ
Protect3GND
GND
GND
GND
AMP+13V
BL-SW
IC1301_GATEGND
J125
J127
J116BL-SW
J133
GND
J117AMP+13V
J141
J145
J178
C1001
C1101
J157
J119
D1102
C1205
C1105
GND
Protect3
GND
D1307__Cathode
GP001
2 1
BA
BC1301
BC1201
BC1101
GNDJ124
R1115
J114
J122
GND
L1101
L1201
J113
BC1302
BC1202
BC1102
J104GND
J105AMP+13V
Outer__
GND
J193
J115Q1102
__Gate
J101GND
J181
Protect3
D1302
R1315
D1202
R1215
R1221
C1115C1116
R1223
R1118C1117
R1224
R1101
R1225
R1102
C1211C1212 R1103
R1301
R1104
C1213
R1302
R1222
C1214
R1303 R1106
C1215
R1304
R1107
C1216
R1108
C1217
R1306
R1109
C1310
R1307
R1110
R1308 R1111
R1309
R1112
C1313
R1310
R1113
C1314
R1311
R1114
C1315
R1312
C1316
R1313
R1119
R1314
R1120
R1318
R1121
R1319
R1122R1320
R1123
R1321
R1124
R1322
R1125
R1323
R1209
R1201R1202
R1203
C1312
R1205
R1206
C1311
R1208
R1305
R1211R1212
R1213
R1218
R1220
C1114
C1113C1112C1111
C1210
Q1101
Q1201
Q1202
Q1302
Q1301 C1110
R1105
R1204
R1207
R1210
Q1102
R1214
R1116
R1117
R1316
R1317
R1126R1127
R1226R1227
C1202
C1203
C1207C1208
C1209
C1102
C1103
C1107
C1108
C1109
C1302
C1303
C1307
C1308
C1309
R1128
R1129
R1130
R1328
R1329
R1330
R1228
R1229
R1230
R1324
R1219
C1118
C1119
C1318
C1319
L1202
L1203
C1218
C1219
L1102
L1103
L1302
L1301
IC1101IC1301
IC1201
D1103
D1105
D1106 D1107
D1203
D1205
D1206D1207
D1303
D1305
D1306
D1307
D613
C604
L602
C614
R1624
C1612
C1615
C1613
Q1602
C1622
CN1001
D602
D601
D604
D603
C601
D607
C602
R602JS601
D605
C605
L601
C1707
R618
T1602 J143
PRI__
GND
J121PFC
__VIN
J120PFC
__VIN J156PRI__
GND
VIN
5 4 3
L601A
L602A
BC1601
BC1602
C1626
J135PFC
__VIN
J136PFC
__VIN
J108
GND
JS602VIN
J132PFC__GND
F602T 2.5A L/250V
D606
BC1604
BC603
SA601
D609A
C1317
R1325
R609R604
R605
R608
R610R611
R614
R625R626
R1326R1327
R1626
R624
L1303
D1604
D611A
C625
R1630
D609
C619
C606
C1602
C620
C616
C615
Q601
BC602
T601
D650
D651
C652
C654C655D65
5
D653
CN501
D1603C1623
Q1601
C1614
IC1702IC1703
Q1704
C1708
C723
D712
D711
D710
D1605
IC1602IC1603
IC602IC603
R679
D654
D660
BC1703
Q657
C650
C1706
R678
R676
C656
C725
D704
D1707
BA3AU0F0102 3
J168
J163
J182
J184
J177
J189
J191
J183
J162
J170
J169
J187
J165
J186
J180
J152
J147
T1601
J153
J185
J176
PRI__
GND
Outer__
GND
Outer__GND
GND
GND
GND
PFC__VOUT
DRIVE
P-ON__
H2
P-ON+21V
AMP+13V
GND
C1709
C665
C692
J159
J171
PFC__GND
J166
J179Q691__
Base
C1618
J175GND
J173
J174
AMP+13V
J190GND
J151C651
R1719
C726
C662
C663
ALL+3.3V
GP002
GP003 DC
J161 PFC__
VOUT
J148GDA
J150
ZCDB J158
IC1601__
Vcc
J160
IC601__
FB
J154
J149J155GND
PFC__GND
D713
J110
J102
T1701
D656__
Cathode
J130
PFC__VOUT
PFC
J167IC601
__FB
BC1603
D619A
D714A
D620AD621A
R1703
R1704
R1705
R1707
R1708
R1710R1711
C1701 C1702
C1703
C1704
R603
R651
R652
R653
R659
R1638
R660
R1639
R661
R1640
R666
R1642
R1645
R674R675
R1653
R1654
R1655
R1701
R1702
R693
C721
C691
C664
C660
C639
C638
C637C635
C633
C632
C630
C631
R740R1709
R669
R668
R667
R658
Q650
Q653
Q1701
Q691
Q1607
Q1608
Q1702
R1622
R1611
C1611
R1610
C1609
C1607
C1610
C1601
R1608
C1605R1607
R1627
R1621R1616
C1608
C1606C1604
C1603
R1606R1609
C1624
R1623
R606
C608
R743
C607
C612
R607
R745
R744
C610
IC651
Q1604
C722
C1625
R617
R619
R1712R1714
R1718
R654R655
R657
R663
R664
R665
R683
R684
R685
R686
R687
R688
R689
R1601
R1602R1604
R1605
R1612
R1613
R1614R1615
R1617
R1618
R1619
R738
R739
R1620
R741
R1625
R1633
R1634
R1637
C1004
R630
R631
R691
R746
R747
Q654
R656
R662
Q701
Q702
R701R702
R703
R704
C701
C636R692
R1656
IC1701
IC601
IC1601
Q657A
D1602
D1608
D1610
D1704
D1710
D1711
D405
D406
D615D617
D618
D657
D661
D662
D663
C1710
Q602
R1629
D619
D620
D621
D714
D664
D1705
D656
D614A
R634
R1720
Power Supply CBA Bottom ViewBecause a hot chassis ground is present in the power supply circuit, an isolation transformer must be used when repairing.Also, in order to have the ability to increase the input slowly, when troubleshooting this type of power supply circuit, a variable isolation transformer is required.
BA3AU0F01023
NOTE:The voltage for parts in hot circuit is measured using hot GND as a common terminal.
CAUTION !Fixed voltage (or Auto voltage selectable) power supply circuit is used in this unit. If Main Fuse (F602) is blown , check to see that all components in the power supply circuit are not defective before you connect the AC plug to the AC power supply. Otherwise it may cause some components in the power supply circuit to fail.
For continued protection against risk of fire, replace only with same type 2.5A, 250V fuse.
CAUTION ! :
ATTENTION : Utiliser un fusible de rechange de même type de 2.5A, 250V.2.5A 250V
PL13.14AWI11-1
WIRING DIAGRAMS
1 23CN
501
1 23
CN
3601 1 51
CN
39061 9
CN
3105
16
CN
1001
BW
CN
601
DIG
ITA
L M
AIN
CB
A U
NIT
PO
WE
R S
UP
PLY
CB
A
AC
CO
RD
ET
HE
RN
ET
JA
CK
CL3
701
CL3
013
CL3
101
WIR
ELE
SS
LA
N M
OD
ULE
14
CN
3801
SP
3801
SP
EA
KE
RL-
CH
SP
3802
SP
EA
KE
RR
-CH
CL3
801
TU
NE
R U
NIT
CO
MP
ON
EN
T-Y
/VID
EO
-IN
CO
MP
ON
EN
T-P
b-IN
CO
MP
ON
EN
T-P
r-IN
AU
DIO
(L)-
IN
AU
DIO
(R)-
IN
RE
AR
DIG
ITA
L A
UD
IO-O
UT
(C
OA
XIA
L)
HD
MI-
CO
NN
EC
TO
R-1
HD
MI-
CO
NN
EC
TO
R-2
HD
MI-
CO
NN
EC
TO
R-3
PC
-RG
B-I
N
US
B J
AC
K
SID
E
HE
AD
PH
ON
EJA
CK
9 1
CN
4052
IR S
EN
SO
R C
BA
UN
ITF
UN
CT
ION
CB
A U
NIT
1 2
CN
4001
1 2
CN
4051
CL4
001
1 68
CN
_L 1 68
CN
_RL
CD
MO
DU
LE
LC
D P
AN
EL
AS
SE
MB
LY
T-C
ON
CB
A U
NIT
[TYPE A]
[TYPE B]
PL13.14BWI11-2
23 1CN
501
1 23
CN
3602 1 51
CN
30131 9
CN
3101
16
CN
1001
BW
CN
601
DIG
ITA
L M
AIN
CB
A U
NIT
PO
WE
R S
UP
PLY
CB
A
AC
CO
RD
CL3
701
CL3
013
CL3
101
14
CN
3801
SP
3801
SP
EA
KE
RL-
CH
SP
3802
SP
EA
KE
RR
-CH
CL3
801
TU
NE
R U
NIT
CO
MP
ON
EN
T-Y
/VID
EO
-IN
CO
MP
ON
EN
T-P
b-IN
CO
MP
ON
EN
T-P
r-IN
AU
DIO
(L)-
IN
AU
DIO
(R)-
IN
RE
AR
DIG
ITA
L A
UD
IO-O
UT
(C
OA
XIA
L)
HD
MI-
CO
NN
EC
TO
R-1
HD
MI-
CO
NN
EC
TO
R-2
HD
MI-
CO
NN
EC
TO
R-3
PC
-RG
B-I
N
US
B J
AC
K
SID
E
HE
AD
PH
ON
EJA
CK
9 1
CN
4052
IR S
EN
SO
R C
BA
UN
ITF
UN
CT
ION
CB
A U
NIT
1 2
CN
4001
1 2
CN
4051
CL4
001
1 68
CN
_L 1 68
CN
_RL
CD
MO
DU
LE
LC
D P
AN
EL
AS
SE
MB
LY
T-C
ON
CB
A U
NIT
12-1 PL13.14CEX
EXPLODED VIEWS
[TYPE A]
A15
See Electrical Parts Listfor parts with this mark.
Digital Main CBA Unit
Power Supply CBAFunction CBA Unit
T-CON CBA Unit
LCD1
A16
A5
A17
AC601
S7
SP3801
SP3802
L23 L23
L23
L23
L23
L23
L10
L10A13
L10
L10
L10
A21
A1
A4-1
L10
L10
X6
A7
A4-2
L44B10
L23
L23
B23
CL3801CL3101
CL3013
CL3701
L10
L23
SSK1
SSK1
SSK1
S7 L24
L24
L6
L6L6
L6
B17
B17
B17
B17
A3
L24
L35
L35
L35
B19
B19
B19
L44
SNA1
SNA1SBA1
SBA1
IR Sensor CBA Unit
B12
CL4001L23
L66
F01
B6
L66
B6
L10
F01
GP001
GP003
A21
A21
[46PFL3608/F7, 46PFL3608/F7 A]
[46PFL3908/F7, 46PFL3908/F8]
[46PFL3608/F7 (Serial No.: DS1, DS2), 46PFL3908/F7 (Serial No.: DS1, DS2), 46PFL3608/F7 A (Serial No.: DS3)]
[46PFL3608/F7 (Serial No.: DS2), 46PFL3908/F7 (Serial No.: DS2), 46PFL3908/F8 (Serial No.: XA2), 46PFL3608/F7 A (Serial No.: DS3)]
[All models except 46PFL3608/F7 (Serial No.: DS2), 46PFL3908/F7 (Serial No.: DS2), 46PFL3908/F8 (Serial No.: XA2), 46PFL3608/F7 A (Serial No.: DS3) ]
L66
L23
L66
12-2 PL13.14CEX
[TYPE B]
A15
See Electrical Parts Listfor parts with this mark.
Digital Main CBA Unit
Power Supply CBA
Function CBA Unit
T-CON CBA Unit
LCD1
A16
A5
A17
AC601
S7
SP3801
SP3802
L23 L23
L23
L23
L23
L23
L10
L10A13
L10
L10
L10
A21
A1
A4-1
L10
L10
X6
A7
A4-2
L44B10
L23
L23
B23
CL3801CL3101
CL3013
CL3701
L10
L23
SSK1
SSK1
S7 L24
L24
L6
L6L6
L6
B17
B17
B17
B17
A3
L24
L35
L35
L35
B19
B19
B19
L44
SNA1
SBA1
IR Sensor CBA Unit
B12
CL4001
L23
L66
F01
B6
L66L10
GP001
GP003
A21
A21
[46PFL3708/F7 (Serial No.: DS1)]
12-3 PL13.14PEX
Packing
[46PFL3708/F7, 46PFL3908/F7, 46PFL3708/F8, 46PFL3908/F8]
[46PFL3608/F7, 46PFL3608/F7 A]
[46PFL3708/F8 (Serial No.: XA1), 46PFL3908/F8 (Serial No.: XA1, XA2)]
Packing Tape
Packing Tape
Packing Tape
Packing Tape
Some Ref. Numbers are not in sequence.
S7
S12
S4
X22
S6
S3
SSK1
SBA1
SNA1
X4X3
X1
X2
Tape
S1
S9
Lower SideUpper Side
REAR SIDE
REAR SIDE
[46PFL3708/F7 (Serial No.: DS1)]
X7
S7
2013/02/16 13-1 A37QACA.fm
TYPE A
PARTS LIST [46PFL3608/F7 (Serial No.: DS1)]
Mechanical Parts
PRODUCT SAFETY NOTE: Products marked with a # have special characteristics important to safety. Before replacing any of these components, read carefully the product safety notice in this service manual. Don't degrade the safety of the product through improper servicing.
NOTE: Parts that are not assigned part numbers (---------) are not available.
LCD PANEL ASSEMBLY
Ref. No. Description Part No.
A3 REAR COVER A37U0UH 1EM030665
A4-1 BOTTOM COVER L A3AQ0UH 1EM030466
A4-2 BOTTOM COVER R A3AQ0UH 1EM030467
A7 FUNCTION KNOB A3AU0UH 1EM334497
A13 JACK HOLDER A37U0UH 1EM334736
A15# RATING LABEL A37QAUH ----------
A16 LOGO LABEL A37U0UH ----------
A17 ENERGY GUIDE LABEL A37QAUH ----------
AC601# AC CORD W/O A GND WIRE UL/CSA/1775/NO/BLACK
WAC172LTE010
B10 STAND BRACKET A3AU0UH 1EM030229A
B12 SENSOR PLATE A3AU0UH 1EM334578
B17 WALL MOUNT BRACKET M6 A21U0UD 1EM332001
B23 WIRE LABEL A3AF0UT ----------
CL3013 FFC WIRE ASSEMBLY 51PIN W/SHIELD 51PIN/427MM
WX1A37Q0P401
CL3101 FFC WIRE ASSEMBLY 9PIN 9PIN/WHITE/327MM
WX1A3AQ0S122
CL3701 FFC WIRE ASSEMBLY 23PIN 23PIN/WHITE/170MM
WX1A37U0S101
CL3801 WIRE ASSEMBLY 4PIN 4PIN/395MM&160MM WX1A3AU0C303
CL4001 WIRE ASSEMBLY 2PIN 2PIN/360MM WX1A3AU0C304
L6 SCREW F-PAN 3CHROM +P-TITE M3X10.0 M3*10 WASHERHEAD+
GCJP3100
L10 SCREW F-PAN BLACK_NI +P-TITE M3X12.0 3X12 WASHER HEAD+BLK
GCHP3120
L23 SCREW BIND 3CHROM +S-TITE M3X6.0 M3X6 BIND HEAD+
GBJS3060
L24 SCREW BIND BLACK_NI +S-TITE M3X6.0 M3X6 BIND HEAD+BLACK
GBHS3060
L44 SEMS-SW PAN 3CHROM + M4X8.0 M4X8 PAN HEAD +
FPJ34080
SBA1 50W STAND BASE ASSEMBLY (FC) A21U0UD 1EMN29162
SNA1 50W STAND HINGE ASSEMBLY (FC) A21U0UD 1EMN29161
SP3801 SPEAKER MAGNETIC 8Ω/10W S0411F19 DS08110XQ004
SP3802 SPEAKER MAGNETIC 8Ω/10W S0411F19 DS08110XQ004
SSK1 STAND SCREW KIT A3AU0UH(SEMS-SW PAN BLACK_NI + M4X12.0)
1ESA34506
PACKINGS1 CARTON A37QAUH 2EMC00042A
S3 STYROFOAM TOP A3AQ0UH 1EM030607
S4 STYROFOAM BOTTOM A3AQ0UH 1EM030945
S6 SET BAG A3AUCUH 2EMC00085
S7 SERIAL NO. LABEL A01PBUH ----------
S9 PAD(580X360X35) A3AU0UH 1EM440437
ACCESSORIESX1 POLYETHYLENE BAG HDPE 180X340XT0.03 1EM435579
X2# OWNERS MANUAL A3RT0UH 2EMN00086
X3 REMOTE CONTROL UNIT YKF340-001 URMT39JHG003
X4 BATTERY R03-B500/01S XB0M451CZB01
X6 QUICK START GUIDE A3RT0UH 1EMN30387A
X22 WARNING MESSAGE FLIER A3AU2UH 2EMN00059
Ref. No. Description Part No.
LCD1# LCD PANEL ASSEMBLY U3FQ0P0
Consists of the following
A1 FRONT CABINET A3AQ2UH 1EM030585
A5 DECORATION PLATE A3AU2UH 1EM228163
A21 BLIND LABEL A3AU0UH ----------
B6 T-CON SHIELD(B) A3AQ0UH 1EM228204
L10 SCREW F-PAN BLACK_NI +P-TITE M3X12.0 3X12 WASHER HEAD+BLK
GCHP3120
L66 SCREW BIND 3CHROM +S-TITE M2.6X6.0 M2.6X6 BIND HEAD+
GBJS9060
LCD MODULE ----------
T-CON CBA UNIT UPB000BEG001
F01 WIRE ASSEMBLY 68PIN FFC SF268-0065FWY00
WX1U3FQ0-F01
Ref. No. Description Part No.
Electrical Parts
PRODUCT SAFETY NOTE: Products marked with a # have special characteristics important to safety. Before replacing any of these components, read carefully the product safety notice in this service manual. Don't degrade the safety of the product through improper servicing.
NOTES:
1. Parts that are not assigned part numbers (---------) are not available.
2. Tolerance of Capacitors and Resistors are noted with the following symbols.
DIGITAL MAIN CBA UNIT
MSW ASSEMBLY
POWER SUPPLY CBA
C.....±0.25% D.....±0.5% F.....±1%
G.....±2% J......±5% K.....±10%
M.....±20% N.....±30% Z.....+80/-20%
Ref. No. Description Part No.
DIGITAL MAIN CBA UNIT A37QAMMA-004
CN3701 WIRELESS LAN MODULE WM5504 UWLMDLACM002
IC3101 IC MAIN PH1-SLD8 MN2WS0270EA QSCA0R0MS053
IC3102 IC NAND FLASH 1GB K9F1G08U0D-SCB0 NSCA0R0SM037
IC3103 16KBIT EEPROM M24C16-WMN6TP NSZBA0TSS259
IC3601 IC RESET IC-PST8429UR QSCA0T0MM075
IC3602 IC DC-DC CONVERTER MP1472GJC452Z NSCA0T09M021
IC3603 IC DC-DC CONVERTER MP1472GJC452Z NSCA0T09M021
IC3604 IC DCDC CONVERTER RT8293ALZSP NSCA0T00B017
IC3607 IC DC-DC CONVERTER MP1472GJC452Z NSCA0T09M021
IC3701 IC USB HIGH-SIDE SW AP2151WG-7/SOT25/5PI
NSCA0TDES015
IC3803 IC D-CLASS AUDIO POWER AMPLIFI TPA3110D2PWPR
NSCA0T0TY073
IC3901 IC DC-DC CONVERTER MP1472GJC452Z NSCA0T09M021
TU3001 TUNER UNIT U9001UH U9001UH
When you replace one of the below ICs on this CBA, replace with the one that has the same part number. Do not mix ICs with different part number.
IC3401 IC 1GB DDR3 SDRAM K4B1G1646G-BCH9 NSCA0R0SM043
IC3402 IC 1GB DDR3 SDRAM K4B1G1646G-BCH9 NSCA0R0SM043
or
IC3401 IC 1GB DDR3 SDRAM H5TQ1G63DFR-H9C NSCA0R0HY018
IC3402 IC 1GB DDR3 SDRAM H5TQ1G63DFR-H9C NSCA0R0HY018
or
IC3401 IC 1GB DDR3 SDRAM H5TQ1G63EFR-H9C NSCA0R0HY035
IC3402 IC 1GB DDR3 SDRAM H5TQ1G63EFR-H9C NSCA0R0HY035
Ref. No. Description Part No.
MSW ASSEMBLYConsists fo the following
A3AU2MSW-002
FUNCTION CBA UNIT A3AU2MSW-002-FN
IR SENSOR CBA UNIT A3AU2MSW-002-IR
IC4051 IC LIGHT SENSOR PH5502B2NA1-E4 QP1ZPH5502B2
Ref. No. Description Part No.
POWER SUPPLY CBAConsists fo the following
A37Q0MPW-002
CAPACITORSC601# CAP METALLIZED FILM 0.22µF/310V /K/LE-MX CTA2240DC001
C602 CAP METALLIZED FILM 0.1µF/310V /K/LE-MX CTA1040DC001
C604# CAP METALLIZED FILM 0.1µF/310V /K/LE-MX CTA1040DC001
C605 CAP ELE 33µF/400V/M/85 CEN3300V8007
C606 CERAMIC CAP RB 1000pF/2kV CA3D102TE006
C607 CHIP CERAMIC CAP.(1608) B K 1000pF/50V CHD1JK30B102
C608 CHIP CERAMIC CAP. CH J 150pF/50V CHD1JJ3CH151
C610 CHIP CERAMIC CAP. B K 220pF/50V CHD1JK30B221
C611 CHIP CERAMIC CAP.(1608) B K 0.1µF/50V CHD1JK30B104
C612 CHIP CERAMIC CAP.(1608) B K 1000pF/50V CHD1JK30B102
C614# CAP METALLIZED FILM 1.0µF/310V /K/LE-MX CTA1050DC001
C615 CAP ELE 47µF/50V/M/85 CEF4700V8006
C616 CAP ELE 220µF/35V/M/85 CEE2210V8006
C619# SAFTY CAP. 1000pF/250V KX CA2E102MR101
C620 CAP ELE 33µF/35V/M/85 CEE3300V8006
C621 CHIP CERAMIC CAP.(1608) B K 4700pF/50V CHD1JK30B472
C622 CHIP CERAMIC CAP.(1608) B K 1000pF/50V CHD1JK30B102
C624 CHIP CERAMIC CAP.(1608) B K 0.1µF/50V CHD1JK30B104
C625 CHIP CERAMIC CAP. B K 2200pF/50V CHD1JK30B222
C650 CAP CERAMIC HV 2200pF/1kV B K CA3A222TE006
C651 CAP ELE 470µF/25V/M/85 CED4710V8006
C652 CAP ELE 470µF/25V/M/85 CED4710V8006
C654 CAP ELE 470µF/16V/M/85 CEC4710V8006
C655 CAP ELE 470µF/16V/M/85 CEC4710V8006
C656 CAP ELE 1µF/50V/M/85 CEF1R00V8006
C660 CHIP CERAMIC CAP.(1608) B K 0.1µF/50V CHD1JK30B104
C662 CAP ELE 22µF/50V/M/85 CEF2200V8006
C663 CAP ELE 100µF/10V/M/85 CEB1010V8006
C665 CERAMIC CAP. RB 680pF/2kV CA3D681TE006
C691 CHIP CERAMIC CAP.(1608) B K 0.01µF/50V CHD1JK30B103
C692 CAP ELE 33µF/35V/M/85 CEE3300V8006
C721 CHIP CERAMIC CAP.(1608) B K 0.1µF/50V CHD1JK30B104
C722 CHIP CERAMIC CAP.(1608) B K 0.1µF/50V CHD1JK30B104
C723 CAP ELE 470µF/63V/M/85 CEG4710V8007
C724 CAP ELE 470µF/63V/M/85 CEG4710V8007
C725 CAP CERAMIC HV 2200pF/1kV B K CA3A222TE006
C726 CERAMIC CAP RB 1500pF/2kV CA3D152TE006
C1001 CAP ELE 470µF/63V/M/85 CEG4710V8007
C1004 CHIP CERAMIC CAP.(3216) X7R K 1.0µF/100V CA2A105MR080
C1101 CAP ELE 100µF/63V/M/85 CEG1010V8006
C1102 CHIP CERAMIC CAP.(3216) X7R K 1.0µF/100V CA2A105MR080
C1103 CHIP CERAMIC CAP.(3216) X7R K 1.0µF/100V CA2A105MR080
C1105 CAP ELE 100µF/100V/M/85 CEH1010V8007
C1107 CHIP CERAMIC CAP.(3216) X7R K 1.0µF/100V CA2A105MR080
C1108 CHIP CERAMIC CAP.(3216) X7R K 1.0µF/100V CA2A105MR080
C1109 CHIP CERAMIC CAP.(3216) X7R K 1.0µF/100V CA2A105MR080
C1110 CHIP CERAMIC CAP.(1608) B K 1µF/25V CHD1EK30B105
C1112 CHIP CERAMIC CAP.(1608) B K 0.047µF/25V CHD1EK30B473
C1113 CHIP CERAMIC CAP.(1608) B K 1000pF/50V CHD1JK30B102
C1114 CHIP CERAMIC CAP.(1608) B K 1µF/25V CHD1EK30B105
C1115 CHIP CERAMIC CAP.(1608) B K 0.022µF/50V CHD1JK30B223
C1116 CHIP CERAMIC CAP. B K 2200pF/50V CHD1JK30B222
C1117 CHIP CERAMIC CAP. B K 2200pF/50V CHD1JK30B222
C1118 CHIP CERAMIC CAP.(3216) X7R K 1.0µF/100V CA2A105MR080
C1119 CHIP CERAMIC CAP. B K 560pF/50V CHD1JK30B561
2013/02/16 13-2 A37QAEL.fm
C1201 CAP ELE 100µF/63V/M/85 CEG1010V8006
C1202 CHIP CERAMIC CAP.(3216) X7R K 1.0µF/100V CA2A105MR080
C1203 CHIP CERAMIC CAP.(3216) X7R K 1.0µF/100V CA2A105MR080
C1205 CAP ELE 100µF/100V/M/85 CEH1010V8007
C1207 CHIP CERAMIC CAP.(3216) X7R K 1.0µF/100V CA2A105MR080
C1208 CHIP CERAMIC CAP.(3216) X7R K 1.0µF/100V CA2A105MR080
C1209 CHIP CERAMIC CAP.(3216) X7R K 1.0µF/100V CA2A105MR080
C1210 CHIP CERAMIC CAP.(1608) B K 1µF/25V CHD1EK30B105
C1212 CHIP CERAMIC CAP.(1608) B K 0.047µF/25V CHD1EK30B473
C1213 CHIP CERAMIC CAP.(1608) B K 1000pF/50V CHD1JK30B102
C1214 CHIP CERAMIC CAP.(1608) B K 1µF/25V CHD1EK30B105
C1215 CHIP CERAMIC CAP.(1608) B K 0.022µF/50V CHD1JK30B223
C1216 CHIP CERAMIC CAP. B K 2200pF/50V CHD1JK30B222
C1217 CHIP CERAMIC CAP. B K 2200pF/50V CHD1JK30B222
C1218 CHIP CERAMIC CAP.(3216) X7R K 1.0µF/100V CA2A105MR080
C1219 CHIP CERAMIC CAP. B K 560pF/50V CHD1JK30B561
C1301 CAP ELE 100µF/63V/M/85 CEG1010V8006
C1302 CHIP CERAMIC CAP.(3216) X7R K 1.0µF/100V CA2A105MR080
C1303 CHIP CERAMIC CAP.(3216) X7R K 1.0µF/100V CA2A105MR080
C1305 CAP ELE 100µF/100V/M/85 CEH1010V8007
C1307 CHIP CERAMIC CAP.(3216) X7R K 1.0µF/100V CA2A105MR080
C1308 CHIP CERAMIC CAP.(3216) X7R K 1.0µF/100V CA2A105MR080
C1309 CHIP CERAMIC CAP.(3216) X7R K 1.0µF/100V CA2A105MR080
C1310 CHIP CERAMIC CAP.(1608) B K 1µF/25V CHD1EK30B105
C1312 CHIP CERAMIC CAP.(1608) B K 0.047µF/25V CHD1EK30B473
C1313 CHIP CERAMIC CAP.(1608) B K 1000pF/50V CHD1JK30B102
C1314 CHIP CERAMIC CAP.(1608) B K 1µF/25V CHD1EK30B105
C1315 CHIP CERAMIC CAP.(1608) B K 0.022µF/50V CHD1JK30B223
C1316 CHIP CERAMIC CAP. B K 2200pF/50V CHD1JK30B222
C1317 CHIP CERAMIC CAP. B K 2200pF/50V CHD1JK30B222
C1318 CHIP CERAMIC CAP.(3216) X7R K 1.0µF/100V CA2A105MR080
C1319 CHIP CERAMIC CAP. B K 560pF/50V CHD1JK30B561
C1601 CHIP CERAMIC CAP.(1608) B K 0.022µF/50V CHD1JK30B223
C1602 CAP ELE 4.7µF/50V/M/85 CEF4R70V8006
C1603 CHIP CERAMIC CAP.(1608) B K 0.22µF/25V CHD1EK30B224
C1604 CHIP CERAMIC CAP.(1608) B K 2.2µF/10V CHD1AK30B225
C1605 CHIP CERAMIC CAP. B K 1200pF/50V CHD1JK30B122
C1606 CHIP CERAMIC CAP.(1608) B K 1000pF/50V CHD1JK30B102
C1607 CHIP CERAMIC CAP. B K 1200pF/50V CHD1JK30B122
C1608 CHIP CERAMIC CAP.(1608) B K 1000pF/50V CHD1JK30B102
C1609 CHIP CERAMIC CAP.(1608) CH J 22pF/50V CHD1JJ3CH220
C1610 CHIP CERAMIC CAP.(1608) CH J 22pF/50V CHD1JJ3CH220
C1611 CHIP CERAMIC CAP.(1608) B K 0.1µF/50V CHD1JK30B104
C1612# CAP METALLIZED FILM 0.22µF/310V /K/LE-MX CTA2240DC001
C1618 CAP ELE 10µF/50V/M/85 CEF1000V8006
C1621 CAP ELECTROLYTIC 100µF/400V/M/22/25 CA2H101DYG17
C1624 CHIP CERAMIC CAP.(1608) B K 0.1µF/50V CHD1JK30B104
C1626 CERAMIC CAP. RB 470pF/2kV CA3D471TE006
C1701 CHIP CERAMIC CAP.(1608) B K 1000pF/50V CHD1JK30B102
C1702 CHIP CERAMIC CAP. CH J 150pF/50V CHD1JJ3CH151
C1703 CHIP CERAMIC CAP. B K 220pF/50V CHD1JK30B221
C1704 CHIP CERAMIC CAP.(1608) B K 0.1µF/50V CHD1JK30B104
C1706 CERAMIC CAP RB 1000pF/2kV CA3D102TE006
C1707# SAFTY CAP. 1000pF/250V KX CA2E102MR101
C1708 CAP ELE 33µF/400V/M/85 CEN3300V8007
C1709 CAP ELE 220µF/10V/M/85 CEB2210V8006
C1710 CHIP CERAMIC CAP.(1608) B K 1000pF/50V CHD1JK30B102
CONNECTORSCN501 FFC CONNECTOR IMSA-9615S-23A-PP-A JC96J23ER007
CN601# CONNECTOR B2P3-VH(LF)(SN) J3VH020JG001
CN1001 PH CONNECTOR TOP 6P B6B-PH-K-S (LF)(SN)
J3PHC06JG029
Ref. No. Description Part No.
DIODESD601# DIODE 1N5406BH NDL1001N5406
D602# DIODE 1N5406BH NDL1001N5406
D603# DIODE 1N5406BH NDL1001N5406
D604# DIODE 1N5406BH NDL1001N5406
D605 RECTIFIER DIODE 1N4005 NDWZ001N4005
D606 RECTIFIER DIODE 1N4005 NDWZ001N4005
D607 DIODE 1N5406BH NDL1001N5406
D609 DIODE FAST RECOVERY RS1GJTD ND1Z0RS1GJTD
D613# DIODE ZENER 1ZB36BB NDWZ0001ZB36
D614 ZENER DIODE SMD TFZVTR27B QD1B00TFZV27
D615 DIODE SWITCHING HSC119 TRF -E QD1Z00HSC119
D617 DIODE SWITCHING HSC119 TRF -E QD1Z00HSC119
D618 ZENER DIODE SMD TFZVTR18B QD1B00TFZV18
D619 DIODE FAST RECOVERY RS1GJTD ND1Z0RS1GJTD
D620 DIODE FAST RECOVERY RS1GJTD ND1Z0RS1GJTD
D621 DIODE FAST RECOVERY RS1GJTD ND1Z0RS1GJTD
D623 ZENER DIODE MM5Z5V6B ND1BMM5Z5V6B
D650 DIODE SHOTTKY SB3200BR NDWZ3200D027
D653 DIODE SCHOTTKY SB3150BH NDWZ00SB3150
D654 DIODE ZENER 1ZB20BB NDWZ0001ZB20
D655 DIODE SCHOTTKY SB3150BH NDWZ00SB3150
D656 DIODE FAST RECOVERY RS1GJTD ND1Z0RS1GJTD
D657 ZENER DIODE MM5Z4V3B ND1BMM5Z4V3B
D660 IC SHUNT REGULATOR SL431A-AT NSZBA0TAUK01
D661 DIODE SWITCHING HSC119 TRF -E QD1Z00HSC119
D662 DIODE SWITCHING HSC119 TRF -E QD1Z00HSC119
D663 DIODE SWITCHING HSC119 TRF -E QD1Z00HSC119
D664 DIODE FAST RECOVERY RS1KJTD ND1Z0RS1KJTD
D704 IC SHUNT REGULATOR SL431A-AT NSZBA0TAUK01
D710 DIODE SHOTTKY SB3200BR NDWZ3200D027
D711 DIODE SHOTTKY SB3200BR NDWZ3200D027
D712 DIODE SHOTTKY SB3200BR NDWZ3200D027
D714 DIODE FAST RECOVERY RS1KJTD ND1Z0RS1KJTD
D1102 DIODE SCHOTTKY BARRIER SB2150BD NDWZ00SB2150
D1103 DIODE SWITCHING HSC119 TRF -E QD1Z00HSC119
D1105 ZENER DIODE SMD TFZGTR39C QD1C000TFZ39
D1107 DIODE SWITCHING HSC119 TRF -E QD1Z00HSC119
D1202 DIODE SCHOTTKY BARRIER SB2150BD NDWZ00SB2150
D1203 DIODE SWITCHING HSC119 TRF -E QD1Z00HSC119
D1205 ZENER DIODE SMD TFZGTR39C QD1C000TFZ39
D1207 DIODE SWITCHING HSC119 TRF -E QD1Z00HSC119
D1302 DIODE SCHOTTKY BARRIER SB2150BD NDWZ00SB2150
D1303 DIODE SWITCHING HSC119 TRF -E QD1Z00HSC119
D1305 ZENER DIODE SMD TFZGTR39C QD1C000TFZ39
D1307 DIODE SWITCHING HSC119 TRF -E QD1Z00HSC119
D1603 DIODE FAST RECOVERY 30PFB60 QDWZ030PFB60
D1605 DIODE FAST RECOVERY 30PFB60 QDWZ030PFB60
D1608 ZENER DIODE SMD TFZVTR16B QD1B00TFZV16
D1705 DIODE FAST RECOVERY RS1GJTD ND1Z0RS1GJTD
D1707 DIODE ZENER 1ZB36BB NDWZ0001ZB36
D1711 ZENER DIODE SMD TFZVTR27B QD1B00TFZV27
ICSIC601 IC SWITCHING FA5640N-C6-TE3/SOP-8 QSCA0T0FD007
IC602# IC PHOTOCOUPLER TLP781F(D4-FUNBLL F) QPEL781FBLLF
IC604 IC SHUNT REGULATOR SL431A-AT NSZBA0TAUK01
IC651 IC REGULATOR AP1117E33G-13 /3PIN NSCA0TDES017
IC1101 IC LED BACKLIGHT CONTROLLER BD9488F-GE2/SOP/18P
QSCA0T0RM418
IC1201 IC LED BACKLIGHT CONTROLLER BD9488F-GE2/SOP/18P
QSCA0T0RM418
IC1301 IC LED BACKLIGHT CONTROLLER BD9488F-GE2/SOP/18P
QSCA0T0RM418
Ref. No. Description Part No.
2013/02/16 13-3 A37QAEL.fm
IC1601 IC DUAL-PHASE PFC CONTROLLER UCC28063DR/R-PDSO-G
NSCA0T0TY087
IC1602# IC PHOTOCOUPLER TLP781F(D4-FUNBLL F) QPEL781FBLLF
IC1701 IC SWITCHING FA5640N-C6-TE3/SOP-8 QSCA0T0FD007
IC1702# IC PHOTOCOUPLER TLP781F(D4-FUNBLL F) QPEL781FBLLF
COILSL601A# LINE FILTER JLB24136 LLEG0Z0XB032
L602A# LINE FILTER JLB24136 LLEG0Z0XB032
L1101 COIL POWER INDUCTORS DIP RP1315BNP-101M/100µH
LLF1010SF013
L1102 COIL CHIP BEADS PZ2012D121-2R5T(F) LLF121SSN006
L1103 COIL CHIP BEADS PZ2012D121-2R5T(F) LLF121SSN006
L1201 COIL POWER INDUCTORS DIP RP1315BNP-101M/100µH
LLF1010SF013
L1202 COIL CHIP BEADS PZ2012D121-2R5T(F) LLF121SSN006
L1203 COIL CHIP BEADS PZ2012D121-2R5T(F) LLF121SSN006
L1301 COIL POWER INDUCTORS DIP RP1315BNP-101M/100µH
LLF1010SF013
L1302 COIL CHIP BEADS PZ2012D121-2R5T(F) LLF121SSN006
L1303 COIL CHIP BEADS PZ2012D121-2R5T(F) LLF121SSN006
TRANSISTORSQ601 FET MOS TK3A65D(FND Q) QEWZTK3A65DQ
Q602 FET MOS TK3P50D RQ(S QF2Z0TK3P50D
Q603 CHIP TRANSISTOR KTC3875S-Y-RTK/P NQ1YKTC3875S
Q650 CHIP TRANSISTOR KTC3875S-Y-RTK/P NQ1YKTC3875S
Q653 CHIP TRANSISTOR KTC3875S-Y-RTK/P NQ1YKTC3875S
Q654 CHIP TRANSISTOR KTC3875S-Y-RTK/P NQ1YKTC3875S
Q691 CHIP TRANSISTOR KTC3875S-Y-RTK/P NQ1YKTC3875S
Q701 CHIP TRANSISTOR KTC3875S-Y-RTK/P NQ1YKTC3875S
Q702 CHIP TRANSISTOR KTC3875S-Y-RTK/P NQ1YKTC3875S
Q1101 FET MOS SMD AP18T10AGH-HF NF2Z18T10AGH
Q1102 FET MOS SMD AP18T10AGH-HF NF2Z18T10AGH
Q1201 FET MOS SMD AP18T10AGH-HF NF2Z18T10AGH
Q1202 FET MOS SMD AP18T10AGH-HF NF2Z18T10AGH
Q1301 FET MOS SMD AP18T10AGH-HF NF2Z18T10AGH
Q1302 FET MOS SMD AP18T10AGH-HF NF2Z18T10AGH
Q1601 MOS FET TK8A50D QFWZTK8A50DQ
Q1602 MOS FET TK8A50D QFWZTK8A50DQ
Q1604 NPN TRANSISTOR SMD 2SC5344SY NQZY2SC5344S
Q1607 PNP TRANSISTOR SMD 2SA1576UBTLQ QQ1Q2SA1576U
Q1608 CHIP TRANSISTOR KTC3875S-Y-RTK/P NQ1YKTC3875S
Q1701 CHIP TRANSISTOR KTC3875S-Y-RTK/P NQ1YKTC3875S
Q1702 PNP TRANSISTOR SMD 2SA1576UBTLQ QQ1Q2SA1576U
Q1704 FET MOS TK5A65D(STA4 A Q) QFEZTK5A65DQ
RESISTORSR601# RES. CARBON FILM J 1/2W J 1.2M Ω RCX2125T1003
R604 RES CHIP 1608 1/10W F 2.70k Ω RTW2701HH008
R605 RES CHIP 3216 1/4W J 270 Ω RRX4271HH034
R606 RES CHIP 1608 1/10W J 22k Ω RRXA223HH013
R607 RES CHIP 1608 1/10W J 4.7k Ω RRXA472HH013
R608 RES CHIP 3216 1/4W J 10 Ω RRX4100HH034
R609 RES CHIP 1608 1/10W J 820k Ω RRXA824HH013
R610 RES CHIP 3216 1/4W J 15k Ω RRX4153HH034
R611 RES CHIP 3216 1/4W J 15k Ω RRX4153HH034
R614 RES CHIP 3216 1/4W J 15k Ω RRX4153HH034
R617 RES CHIP 3216 1/4W J 4.7k Ω RRX4472HH034
R618 METAL OXIDE FILM RES. 2W J 0.22 Ω RN02R22ZU001
R619 RES CHIP 1608 1/10W J 4.7 Ω RRXA4R7HH013
R620 RES CHIP 1608 1/10W J 47k Ω RRXA473HH013
R623 RES CHIP 1608 1/10W F 2.70k Ω RTW2701HH008
R624 RES CHIP 3216 1/4W F 510k Ω RTC5103YF004
R625 RES CHIP 3216 1/4W F 510k Ω RTC5103YF004
R626 RES CHIP 3216 1/4W F 510k Ω RTC5103YF004
R627 RES CHIP 1608 1/10W F 39.0k Ω RTW3902HH008
Ref. No. Description Part No.
R628 RES CHIP 1608 1/10W J 22k Ω RRXA223HH013
R629 RES CHIP 1608 1/10W J 47k Ω RRXA473HH013
R630 RES CHIP 3216 1/4W J 560k Ω RRX4564HH034
R631 RES CHIP 3216 1/4W J 560k Ω RRX4564HH034
R632 RES CHIP 1608 1/10W J 8.2k Ω RRXA822HH013
R633 RES CHIP 1608 1/10W J 8.2k Ω RRXA822HH013
R634 RES CHIP 1608 1/10W J 270 Ω RRXA271HH013
R651 RES CHIP 1608 1/10W J 1.0 Ω RRXA1R0HH013
R652 RES CHIP 1608 1/10W J 10k Ω RRXA103HH013
R653 RES CHIP 1608 1/10W F 22.0k Ω RTW2202HH008
R654 RES CHIP 3216 1/4W J 180 Ω RRX4181HH034
R655 RES CHIP 3216 1/4W J 180 Ω RRX4181HH034
R656 RES CHIP 1608 1/10W J 8.2k Ω RRXA822HH013
R657 RES CHIP 3216 1/4W J 3.9k Ω RRX4392HH034
R658 RES CHIP 1608 1/10W J 2.7k Ω RRXA272HH013
R659 RES CHIP 1608 1/10W F 22.0k Ω RTW2202HH008
R660 RES CHIP 1608 1/10W F 2.70k Ω RTW2701HH008
R661 RES CHIP 1608 1/10W F 3.30k Ω RTW3301HH008
R662 RES CHIP 1608 1/10W J 47k Ω RRXA473HH013
R666 RES CHIP 1608 1/10W 0 Ω RRXA000HH014
R667 RES CHIP 1608 1/10W J 8.2k Ω RRXA822HH013
R668 RES CHIP 1608 1/10W J 47k Ω RRXA473HH013
R669 RES CHIP 1608 1/10W J 10k Ω RRXA103HH013
R676 METAL OXIDE FILM RES. 2W J 6.8 Ω RN026R8ZU001
R678 METAL OXIDE FILM RES. 2W J 6.8 Ω RN026R8ZU001
R679 METAL OXIDE FILM RES. 2W J 6.8 Ω RN026R8ZU001
R683 RES CHIP 3216 1/4W J 3.9 Ω RRX43R9HH034
R684 RES CHIP 3216 1/4W J 3.9 Ω RRX43R9HH034
R691 RES CHIP 1608 1/10W J 2.2k Ω RRXA222HH013
R692 RES CHIP 1608 1/10W J 330 Ω RRXA331HH013
R693 RES CHIP 1608 1/10W J 47k Ω RRXA473HH013
R701 RES CHIP 1608 1/10W J 10k Ω RRXA103HH013
R702 RES CHIP 1608 1/10W J 47k Ω RRXA473HH013
R703 RES CHIP 1608 1/10W J 10k Ω RRXA103HH013
R704 RES CHIP 1608 1/10W J 47k Ω RRXA473HH013
R738 RES CHIP 3216 1/4W J 2.2k Ω RRX4222HH034
R739 RES CHIP 3216 1/4W J 15k Ω RRX4153HH034
R740 RES CHIP 1608 1/10W J 2.7k Ω RRXA272HH013
R741 RES CHIP 3216 1/4W J 1.8k Ω RRX4182HH034
R743 RES CHIP 1608 1/10W F 43.0k Ω RTW4302HH008
R744 RES CHIP 1608 1/10W F 1.30k Ω RT1301RYL002
R745 RES CHIP 1608 1/10W F 3.30k Ω RTW3301HH008
R746 RES CHIP 3216 1/4W J 270k Ω RRX4274HH034
R747 RES CHIP 3216 1/4W J 270k Ω RRX4274HH034
R1101 RES CHIP 1608 1/10W J 120 Ω RRXA121HH013
R1102 RES CHIP 1608 1/10W J 120 Ω RRXA121HH013
R1103 RES CHIP 1608 1/10W F 75.0k Ω RTW7502HH008
R1104 RES CHIP 1608 1/10W F 20.0k Ω RTW2002HH008
R1105 RES CHIP 1608 1/10W F 20.0k Ω RTW2002HH008
R1106 RES CHIP 1608 1/10W J 10k Ω RRXA103HH013
R1107 RES CHIP 1608 1/10W J 100k Ω RRXA104HH013
R1108 RES CHIP 1608 1/10W J 1.0k Ω RRXA102HH013
R1109 RES CHIP 1608 1/10W J 10k Ω RRXA103HH013
R1110 RES CHIP 1608 1/10W J 100k Ω RRXA104HH013
R1111 RES CHIP 1608 1/10W F 240k Ω RTW2403HH008
R1112 RES CHIP 1608 1/10W F 33.0k Ω RTW3302HH008
R1113 RES CHIP 1608 1/10W F 3.00k Ω RTW3001HH008
R1114 RES CHIP 1608 1/10W F 62.0k Ω RTW6202HH008
R1115 METAL OXIDE RES. 1W J 0.18 Ω RN01R18ZU001
R1118 RES CHIP 1608 1/10W J 200 Ω RRXA201HH013
R1119 RES CHIP 1608 1/10W F 100k Ω RTW1003HH008
R1120 RES CHIP 1608 1/10W F 110k Ω RT1103RYL002
R1121 RES CHIP 1608 1/10W F 10k Ω RT1002RYL002
Ref. No. Description Part No.
2013/02/16 13-4 A37QAEL.fm
R1122 RES CHIP 1608 1/10W J 1.0k Ω RRXA102HH013
R1123 RES CHIP 1608 1/10W J 10 Ω RRXA100HH013
R1124 RES CHIP 1608 1/10W J 1.0k Ω RRXA102HH013
R1125 RES CHIP 1608 1/10W J 51 Ω RRXA510HH013
R1126 RES CHIP 3216 1/4W F 1.00 Ω RT1R00RYL007
R1127 RES CHIP 3216 1/4W F 1.00 Ω RT1R00RYL007
R1128 RES CHIP 3216 1/4W J 2.2k Ω RRX4222HH034
R1129 RES CHIP 3216 1/4W J 1.8k Ω RRX4182HH034
R1130 RES CHIP 1608 1/10W 0 Ω RRXA000HH014
R1201 RES CHIP 1608 1/10W J 120 Ω RRXA121HH013
R1202 RES CHIP 1608 1/10W J 120 Ω RRXA121HH013
R1203 RES CHIP 1608 1/10W F 75.0k Ω RTW7502HH008
R1204 RES CHIP 1608 1/10W F 20.0k Ω RTW2002HH008
R1205 RES CHIP 1608 1/10W F 20.0k Ω RTW2002HH008
R1206 RES CHIP 1608 1/10W J 10k Ω RRXA103HH013
R1207 RES CHIP 1608 1/10W J 100k Ω RRXA104HH013
R1208 RES CHIP 1608 1/10W J 1.0k Ω RRXA102HH013
R1209 RES CHIP 1608 1/10W J 10k Ω RRXA103HH013
R1210 RES CHIP 1608 1/10W J 100k Ω RRXA104HH013
R1211 RES CHIP 1608 1/10W F 240k Ω RTW2403HH008
R1212 RES CHIP 1608 1/10W F 33.0k Ω RTW3302HH008
R1213 RES CHIP 1608 1/10W F 3.00k Ω RTW3001HH008
R1214 RES CHIP 1608 1/10W F 62.0k Ω RTW6202HH008
R1215 METAL OXIDE RES. 1W J 0.18 Ω RN01R18ZU001
R1218 RES CHIP 1608 1/10W J 200 Ω RRXA201HH013
R1219 RES CHIP 1608 1/10W F 100k Ω RTW1003HH008
R1220 RES CHIP 1608 1/10W F 110k Ω RT1103RYL002
R1221 RES CHIP 1608 1/10W F 10k Ω RT1002RYL002
R1222 RES CHIP 1608 1/10W J 1.0k Ω RRXA102HH013
R1223 RES CHIP 1608 1/10W J 10 Ω RRXA100HH013
R1224 RES CHIP 1608 1/10W J 1.0k Ω RRXA102HH013
R1225 RES CHIP 1608 1/10W J 51 Ω RRXA510HH013
R1226 RES CHIP 3216 1/4W F 1.00 Ω RT1R00RYL007
R1227 RES CHIP 3216 1/4W F 1.00 Ω RT1R00RYL007
R1228 RES CHIP 3216 1/4W J 2.2k Ω RRX4222HH034
R1229 RES CHIP 3216 1/4W J 1.8k Ω RRX4182HH034
R1230 RES CHIP 1608 1/10W 0 Ω RRXA000HH014
R1301 RES CHIP 1608 1/10W J 120 Ω RRXA121HH013
R1302 RES CHIP 1608 1/10W J 120 Ω RRXA121HH013
R1303 RES CHIP 1608 1/10W F 75.0k Ω RTW7502HH008
R1304 RES CHIP 1608 1/10W F 20.0k Ω RTW2002HH008
R1305 RES CHIP 1608 1/10W F 20.0k Ω RTW2002HH008
R1306 RES CHIP 1608 1/10W J 10k Ω RRXA103HH013
R1307 RES CHIP 1608 1/10W J 100k Ω RRXA104HH013
R1308 RES CHIP 1608 1/10W J 1.0k Ω RRXA102HH013
R1309 RES CHIP 1608 1/10W J 10k Ω RRXA103HH013
R1310 RES CHIP 1608 1/10W J 100k Ω RRXA104HH013
R1311 RES CHIP 1608 1/10W F 240k Ω RTW2403HH008
R1312 RES CHIP 1608 1/10W F 33.0k Ω RTW3302HH008
R1313 RES CHIP 1608 1/10W F 3.00k Ω RTW3001HH008
R1314 RES CHIP 1608 1/10W F 62.0k Ω RTW6202HH008
R1315 METAL OXIDE RES. 1W J 0.18 Ω RN01R18ZU001
R1318 RES CHIP 1608 1/10W J 200 Ω RRXA201HH013
R1319 RES CHIP 1608 1/10W F 100k Ω RTW1003HH008
R1320 RES CHIP 1608 1/10W F 110k Ω RT1103RYL002
R1321 RES CHIP 1608 1/10W F 10k Ω RT1002RYL002
R1322 RES CHIP 1608 1/10W J 1.0k Ω RRXA102HH013
R1323 RES CHIP 1608 1/10W J 10 Ω RRXA100HH013
R1324 RES CHIP 1608 1/10W J 1.0k Ω RRXA102HH013
R1325 RES CHIP 1608 1/10W J 51 Ω RRXA510HH013
R1326 RES CHIP 3216 1/4W F 1.00 Ω RT1R00RYL007
R1327 RES CHIP 3216 1/4W F 1.00 Ω RT1R00RYL007
R1328 RES CHIP 3216 1/4W J 2.2k Ω RRX4222HH034
Ref. No. Description Part No.
R1329 RES CHIP 3216 1/4W J 1.8k Ω RRX4182HH034
R1330 RES CHIP 1608 1/10W 0 Ω RRXA000HH014
R1601 RES CHIP 3216 1/4W F 750k Ω RTC7503YF004
R1602 RES CHIP 3216 1/4W F 750k Ω RTC7503YF004
R1604 RES CHIP 3216 1/4W F 750k Ω RTC7503YF004
R1605 RES CHIP 3216 1/4W F 750k Ω RTC7503YF004
R1606 RES CHIP 1608 1/10W J 120k Ω RRXA124HH013
R1607 RES CHIP 1608 1/10W F 220 Ω RTW2200HH008
R1608 RES CHIP 1608 1/10W F 51.0k Ω RTW5102HH008
R1609 RES CHIP 1608 1/10W J 5.6k Ω RRXA562HH013
R1610 RES CHIP 1608 1/10W F 18.0k Ω RTW1802HH008
R1611 RES CHIP 1608 1/10W J 100 Ω RRXA101HH013
R1612 RES CHIP 3216 1/4W F 750k Ω RTC7503YF004
R1613 RES CHIP 3216 1/4W F 750k Ω RTC7503YF004
R1614 RES CHIP 3216 1/4W F 750k Ω RTC7503YF004
R1615 RES CHIP 3216 1/4W F 750k Ω RTC7503YF004
R1616 RES CHIP 1608 1/10W F 47.0k Ω RTW4702HH008
R1617 RES CHIP 3216 1/4W F 750k Ω RTC7503YF004
R1618 RES CHIP 3216 1/4W F 750k Ω RTC7503YF004
R1619 RES CHIP 3216 1/4W F 750k Ω RTC7503YF004
R1620 RES CHIP 3216 1/4W F 750k Ω RTC7503YF004
R1621 RES CHIP 1608 1/10W F 1.80k Ω RTW1801HH008
R1622 RES CHIP 1608 1/10W J 18k Ω RRXA183HH013
R1623 RES CHIP 1608 1/10W J 12k Ω RRXA123HH013
R1624 RES CEMENT 5W J 0.033 Ω RWJL33PAK002
R1625 RES CHIP 3216 1/4W J 47 Ω RRX4470HH034
R1626 RES CHIP 3216 1/4W J 47 Ω RRX4470HH034
R1627 RES CHIP 1608 1/10W J 12k Ω RRXA123HH013
R1633 RES CHIP 3216 1/4W J 2.7k Ω RRX4272HH034
R1634 RES CHIP 3216 1/4W J 47 Ω RRX4470HH034
R1637 RES CHIP 3216 1/4W J 680 Ω RRX4681HH034
R1638 RES CHIP 1608 1/10W J 18k Ω RRXA183HH013
R1639 RES CHIP 1608 1/10W J 10k Ω RRXA103HH013
R1640 RES CHIP 1608 1/10W J 4.7k Ω RRXA472HH013
R1642 RES CHIP 1608 1/10W J 10k Ω RRXA103HH013
R1645 RES CHIP 1608 1/10W F 68.0k Ω RTW6802HH008
R1656 RES CHIP 1608 1/10W J 4.7 Ω RRXA4R7HH013
R1702 RES CHIP 1608 1/10W F 2.70k Ω RTW2701HH008
R1703 RES CHIP 1608 1/10W J 4.7k Ω RRXA472HH013
R1704 RES CHIP 1608 1/10W J 22k Ω RRXA223HH013
R1705 RES CHIP 1608 1/10W J 27k Ω RRXA273HH013
R1707 RES CHIP 1608 1/10W J 820k Ω RRXA824HH013
R1708 RES CHIP 1608 1/10W J 22k Ω RRXA223HH013
R1710 RES CHIP 1608 1/10W J 22k Ω RRXA223HH013
R1711 RES CHIP 1608 1/10W J 10k Ω RRXA103HH013
R1712 RES CHIP 3216 1/4W J 180 Ω RRX4181HH034
R1714 RES CHIP 3216 1/4W J 10 Ω RRX4100HH034
R1718 RES CHIP 3216 1/4W J 22k Ω RRX4223HH034
R1719 METALOXIDE RES 2W J 0.15Ω RNJR15PAK002
R1720 RES CHIP 1608 1/10W J 270 Ω RRXA271HH013
MISCELLANEOUSB19 POW HEAT SINK A7120UH 1EM423993A
BC602 BEADS INDUCTOR FBR07HA121SB-00 LLBF00STU030
BC603 WIRE CP STP-S-0.50 XZ40F0REN001
BC1101 BEADS INDUCTOR FBR07HA121SB-00 LLBF00STU030
BC1102 WIRE CP STP-S-0.50 XZ40F0REN001
BC1201 BEADS INDUCTOR FBR07HA121SB-00 LLBF00STU030
BC1202 WIRE CP STP-S-0.50 XZ40F0REN001
BC1301 BEADS INDUCTOR FBR07HA121SB-00 LLBF00STU030
BC1302 WIRE CP STP-S-0.50 XZ40F0REN001
BC1601 BEADS INDUCTOR FBR07HA121SB-00 LLBF00STU030
BC1602 BEADS INDUCTOR FBR07HA121SB-00 LLBF00STU030
Ref. No. Description Part No.
2013/02/16 13-5 A37QAEL.fm
BC1603 WIRE CP STP-S-0.50 XZ40F0REN001
BC1604 WIRE CP STP-S-0.50 XZ40F0REN001
BC1703 BEADS INDUCTOR FBR07HA121SB-00 LLBF00STU030
F602# FUSE TIME RAG SLT250V2.5A PDGSLB0NG252
GP001 EARTH PLATE A31FBUT 1EM440258
GP003 EARTH PLATE A31FBUT 1EM440258
JS601 WIRE CP STP-S-0.50 XZ40F0REN001
JS602 WIRE CP STP-S-0.50 XZ40F0REN001
L35 SCREW BIND 3CHROM +B-TITE M3X8.0 D3X8 BIND HEAD+
GBJB3080
SA601# VARISTOR 10D 471K SVR NVQZVR10D471
T601# TRANS POWER BCK-28FX LTT2PCMEK055
T1601# COIL EF TE2520A7001 LLEE0ZMEK005
T1602# COIL EF TE2520A7001 LLEE0ZMEK005
T1701# TRANS POWER BCK-35CU LTT3PCMEK028
Ref. No. Description Part No.
2013/02/16 13-6 A37QAEL.fm
2013/12/16 13-7 A37QCCA.fm
TYPE A
PARTS LIST [46PFL3608/F7 (Serial No.: DS2)]
Mechanical Parts
PRODUCT SAFETY NOTE: Products marked with a # have special characteristics important to safety. Before replacing any of these components, read carefully the product safety notice in this service manual. Don't degrade the safety of the product through improper servicing.
NOTE: Parts that are not assigned part numbers (---------) are not available.
Different parts from the original model 46PFL3608/F7 (Serial No. : DS1)
Ref. No. Description Part No.
CL3013 FFC WIRE ASSEMBLY 51PIN(W/SHIELD) 51P/FFC/SHIELD/439MM
WX1A37QCP401
LCD1# LCD PANEL ASSEMBLY U3GQ0P0
B6 T-CON SHIELD(S) A3AQAUH 1EM228205
L23 SCREW BIND 3CHROM +S-TITE M3X6.0 M3X6 BIND HEAD+
GBJS3060
T-CON CBA UNIT UPB0000SM001
F01 WIRE ASSEMBLY 68PIN FFC SF268-0080FWY00
WX1U3GQ0-F01
2013/12/16 13-8 A37QCEL.fm
Electrical Parts
PRODUCT SAFETY NOTE: Products marked with a # have special characteristics important to safety. Before replacing any of these components, read carefully the product safety notice in this service manual. Don't degrade the safety of the product through improper servicing.
NOTES:
1. Parts that are not assigned part numbers (---------) are not available.
2. Tolerance of Capacitors and Resistors are noted with the following symbols.
Different parts from the original model 46PFL3608/F7 (Serial No. : DS1)
C.....±0.25% D.....±0.5% F.....±1%
G.....±2% J......±5% K.....±10%
M.....±20% N.....±30% Z.....+80/-20%
Ref. No. Description Part No.
DIGITAL MAIN CBA UNIT A37QCMMA-001
2014/02/10 13-9 A37QFCA.fm
TYPE A
PARTS LIST [46PFL3608/F7 A(Serial No.: DS3)]
Mechanical Parts
PRODUCT SAFETY NOTE: Products marked with a # have special characteristics important to safety. Before replacing any of these components, read carefully the product safety notice in this service manual. Don't degrade the safety of the product through improper servicing.
NOTE: Parts that are not assigned part numbers (---------) are not available.
Different parts from the original model 46PFL3608/F7 (Serial No. : DS1)
Ref. No. Description Part No.
A15# RATING LABEL A37QFUH ----------
A17 ENERGY GUIDE LABEL A37QFUH ----------
CL3013 FFC WIRE ASSEMBLY 51PIN(W/SHIELD) 51P/FFC/SHIELD/439MM
WX1A37QCP401
S1 CARTON A37QFUH 2EMC00406
X2# OWNERS MANUAL A37QFUH 2EMN00195
X3 REMOTE CONTROL UNIT YKF340-003 URMT41JHG003
X4 BATTERY DRY R03(SIZE AAA) XB00M0RKT001
X6 QUICK START GUIDE A37QFUH 2EMN00196
LCD1# LCD PANEL ASSEMBLY U3GQ0P0
B6 T-CON SHIELD(S) A3AQAUH 1EM228205
L23 SCREW BIND 3CHROM +S-TITE M3X6.0 M3X6 BIND HEAD+
GBJS3060
T-CON CBA UNIT UPB0000SM001
F01 WIRE ASSEMBLY 68PIN FFC SF268-0080FWY00
WX1U3GQ0-F01
2014/02/10 13-10 A37QFEL.fm
Electrical Parts
PRODUCT SAFETY NOTE: Products marked with a # have special characteristics important to safety. Before replacing any of these components, read carefully the product safety notice in this service manual. Don't degrade the safety of the product through improper servicing.
NOTES:
1. Parts that are not assigned part numbers (---------) are not available.
2. Tolerance of Capacitors and Resistors are noted with the following symbols.
Different parts from the original model 46PFL3608/F7 (Serial No. : DS1)
C.....±0.25% D.....±0.5% F.....±1%
G.....±2% J......±5% K.....±10%
M.....±20% N.....±30% Z.....+80/-20%
Ref. No. Description Part No.
DIGITAL MAIN CBA UNIT A37QFMMA-002
IC3101 IC MAIN PH1-SLD8PLUS MN2WS0270HA QSCA0R0MS065
IC3102 IC NAND FLASH 1GB H27U1G8F2BTR-BC NSCA0R0HY009
TU3001 TUNER UNIT U9004UH U9004UH
When you replace one of the below ICs on this CBA, always replace the IC in accordance with the 3 combinations below. Do not mix ICs of different combination.
IC3401 IC 1GB DDR3 SDRAM K4B1G1646G-BCK0 NSCA0R0SM055
IC3402 IC 2GB DDR3 SDRAM K4B2G1646Q-BCMA NSCA0R0SM057
or
IC3401 IC 1GB DDR3 SDRAM H5TQ1G63EFR-PBC NSCA0R0HY039
IC3402 IC 2GB DDR3 SDRAM H5TQ2G63FFR-PBC NSCA0R0HY041
or
IC3401 IC 1GB DDR3 SDRAM NT5CB64M16FP-DH NSCA0R0J2017
IC3402 IC 2GB DDR3 SDRAM NT5CB128M16FP-DI NSCA0R0J2016
2013/03/21 13-11 A37Q0CA.fm
TYPE A
PARTS LIST [46PFL3908/F7 (Serial No.: DS1)]
Mechanical Parts
PRODUCT SAFETY NOTE: Products marked with a # have special characteristics important to safety. Before replacing any of these components, read carefully the product safety notice in this service manual. Don't degrade the safety of the product through improper servicing.
NOTE: Parts that are not assigned part numbers (---------) are not available.
Different parts from the original model 46PFL3608/F7 (Serial No. : DS1)
Ref. No. Description Part No.
A15# RATING LABEL A37Q0UH ----------
A17 ENERGY GUIDE LABEL A37Q0UH ----------
SBA1 50W STAND BASE ASSEMBLY (PF) A21U2UD 1EMN29164
SNA1 50W STAND HINGE ASSEMBLY (PF) A21U2UD 1EMN29163
S1 CARTON A37Q0UH 1EM334722A
2013/03/21 13-12 A37Q0EL.fm
Electrical Parts
PRODUCT SAFETY NOTE: Products marked with a # have special characteristics important to safety. Before replacing any of these components, read carefully the product safety notice in this service manual. Don't degrade the safety of the product through improper servicing.
NOTES:
1. Parts that are not assigned part numbers (---------) are not available.
2. Tolerance of Capacitors and Resistors are noted with the following symbols.
Different parts from the original model 46PFL3608/F7 (Serial No. : DS1)
C.....±0.25% D.....±0.5% F.....±1%
G.....±2% J......±5% K.....±10%
M.....±20% N.....±30% Z.....+80/-20%
Ref. No. Description Part No.
DIGITAL MAIN CBA UNIT A37Q0MMA-004
2013/12/18 13-13 A37QDCA.fm
TYPE A
PARTS LIST [46PFL3908/F7 (Serial No.: DS2)]
Mechanical Parts
PRODUCT SAFETY NOTE: Products marked with a # have special characteristics important to safety. Before replacing any of these components, read carefully the product safety notice in this service manual. Don't degrade the safety of the product through improper servicing.
NOTE: Parts that are not assigned part numbers (---------) are not available.
Different parts from the original model 46PFL3608/F7 (Serial No. : DS1)
Ref. No. Description Part No.
A15# RATING LABEL A37Q0UH ----------
A17 ENERGY GUIDE LABEL A37Q0UH ----------
CL3013 FFC WIRE ASSEMBLY 51PIN(W/SHIELD) 51P/FFC/SHIELD/439MM
WX1A37QCP401
SBA1 50W STAND BASE ASSEMBLY (PF) A21U2UD 1EMN29164
SNA1 50W STAND HINGE ASSEMBLY (PF) A21U2UD 1EMN29163
S1 CARTON A37Q0UH 1EM334722A
LCD1# LCD PANEL ASSEMBLY U3GQ0P0
B6 T-CON SHIELD(S) A3AQAUH 1EM228205
L23 SCREW BIND 3CHROM +S-TITE M3X6.0 M3X6 BIND HEAD+
GBJS3060
T-CON CBA UNIT UPB0000SM001
F01 WIRE ASSEMBLY 68PIN FFC SF268-0080FWY00
WX1U3GQ0-F01
2013/12/18 13-14 A37QDEL.fm
Electrical Parts
PRODUCT SAFETY NOTE: Products marked with a # have special characteristics important to safety. Before replacing any of these components, read carefully the product safety notice in this service manual. Don't degrade the safety of the product through improper servicing.
NOTES:
1. Parts that are not assigned part numbers (---------) are not available.
2. Tolerance of Capacitors and Resistors are noted with the following symbols.
Different parts from the original model 46PFL3608/F7 (Serial No. : DS1)
C.....±0.25% D.....±0.5% F.....±1%
G.....±2% J......±5% K.....±10%
M.....±20% N.....±30% Z.....+80/-20%
Ref. No. Description Part No.
DIGITAL MAIN CBA UNIT A37QDMMA-001
2013/05/27 13-15 A37QBCA.fm
TYPE A
PARTS LIST [46PFL3908/F8 (Serial No.: XA1)]
Mechanical Parts
PRODUCT SAFETY NOTE: Products marked with a # have special characteristics important to safety. Before replacing any of these components, read carefully the product safety notice in this service manual. Don't degrade the safety of the product through improper servicing.
NOTE: Parts that are not assigned part numbers (---------) are not available.
Different parts from the original model 46PFL3608/F7 (Serial No. : DS1)
Ref. No. Description Part No.
A15# RATING LABEL A37QBMA ----------
A16 LOGO LABEL A37UAMA ----------
A17 Not used
SBA1 50W STAND BASE ASSEMBLY (PF) A21U2UD 1EMN29164
SNA1 50W STAND HINGE ASSEMBLY (PF) A21U2UD 1EMN29163
S1 CARTON A37QBMA 2EMC00136
S12 CARTON LABEL A37QBMA ----------
X2# OWNERS MANUAL A3RTAMA 2EMN00024B
X6 QUICK START GUIDE A3RTAMA 2EMN00025A
X22 WARNING MESSAGE FLIER A3AU2UH 2EMN00059A
2013/05/27 13-16 A37QBEL.fm
Electrical Parts
PRODUCT SAFETY NOTE: Products marked with a # have special characteristics important to safety. Before replacing any of these components, read carefully the product safety notice in this service manual. Don't degrade the safety of the product through improper servicing.
NOTES:
1. Parts that are not assigned part numbers (---------) are not available.
2. Tolerance of Capacitors and Resistors are noted with the following symbols.
Different parts from the original model 46PFL3608/F7 (Serial No. : DS1)
C.....±0.25% D.....±0.5% F.....±1%
G.....±2% J......±5% K.....±10%
M.....±20% N.....±30% Z.....+80/-20%
Ref. No. Description Part No.
DIGITAL MAIN CBA UNIT A37QBMMA-003
2014/01/28 13-17 A37QECA.fm
TYPE A
PARTS LIST [46PFL3908/F8 (Serial No.: XA2)]
Mechanical Parts
PRODUCT SAFETY NOTE: Products marked with a # have special characteristics important to safety. Before replacing any of these components, read carefully the product safety notice in this service manual. Don't degrade the safety of the product through improper servicing.
NOTE: Parts that are not assigned part numbers (---------) are not available.
Different parts from the original model 46PFL3608/F7 (Serial No. : DS1)
Ref. No. Description Part No.
A15# RATING LABEL A37QBMA ----------
A16 LOGO LABEL A37UAMA ----------
A17 Not used
CL3013 FFC WIRE ASSEMBLY 51PIN(W/SHIELD) 51P/FFC/SHIELD/439MM
WX1A37QCP401
SBA1 50W STAND BASE ASSEMBLY (PF) A21U2UD 1EMN29164
SNA1 50W STAND HINGE ASSEMBLY (PF) A21U2UD 1EMN29163
S1 CARTON A37QBMA 2EMC00136
S12 CARTON LABEL A37QBMA ----------
X2# OWNERS MANUAL A3RTAMA 2EMN00024B
X6 QUICK START GUIDE A3RTAMA 2EMN00025A
LCD1# LCD PANEL ASSEMBLY U3GQ0P0
B6 T-CON SHIELD(S) A3AQAUH 1EM228205
L23 SCREW BIND 3CHROM +S-TITE M3X6.0 M3X6 BIND HEAD+
GBJS3060
T-CON CBA UNIT UPB0000SM001
F01 WIRE ASSEMBLY 68PIN FFC SF268-0080FWY00
WX1U3GQ0-F01
2014/01/28 13-18 A37QEEL.fm
Electrical Parts
PRODUCT SAFETY NOTE: Products marked with a # have special characteristics important to safety. Before replacing any of these components, read carefully the product safety notice in this service manual. Don't degrade the safety of the product through improper servicing.
NOTES:
1. Parts that are not assigned part numbers (---------) are not available.
2. Tolerance of Capacitors and Resistors are noted with the following symbols.
Different parts from the original model 46PFL3608/F7 (Serial No. : DS1)
C.....±0.25% D.....±0.5% F.....±1%
G.....±2% J......±5% K.....±10%
M.....±20% N.....±30% Z.....+80/-20%
Ref. No. Description Part No.
DIGITAL MAIN CBA UNIT A37QEMMA-002
2013/03/19 13-19 A3AQ2CA.fm
TYPE B
PARTS LIST [46PFL3708/F7 (Serial No.: DS1)]
Mechanical Parts
PRODUCT SAFETY NOTE: Products marked with a # have special characteristics important to safety. Before replacing any of these components, read carefully the product safety notice in this service manual. Don't degrade the safety of the product through improper servicing.
NOTE: Parts that are not assigned part numbers (---------) are not available.
Different parts from the original model 46PFL3608/F7 (Serial No. : DS1)
Ref. No. Description Part No.
A3 REAR COVER A3AU0UH 1EM030226
A13 JACK HOLDER A3AU0UH 1EM334651
A15# RATING LABEL A3AQ2UH ----------
A16 LOGO LABEL A3AU2UH ----------
A17 ENERGY GUIDE LABEL A3AQ2UH ----------
CL3013 FFC WIRE ASSEMBLY 51PIN W/SHIELD 51PIN/457MM
WX1A3AQ0P401
CL3701 FFC WIRE ASSEMBLY 23PIN 23PIN/WHITE/205MM
WX1A3AU0S103
SBA1 50W STAND BASE ASSEMBLY (PF) A21U2UD 1EMN29164
SNA1 50W STAND HINGE ASSEMBLY (PF) A21U2UD 1EMN29163
S1 CARTON A3AQ2UH 1EM334640
X2# OWNERS MANUAL A31T2UH 2EMN00084
X3 REMOTE CONTROL UNIT YKF335-001 URMT39JHG001
X6 QUICK START GUIDE A31T2UH 1EMN30381
X7 REGISTRATION CARD (PHILIPS) A31T2UH 2EMN00134
2013/03/19 13-20 A3AQ2EL.fm
Electrical Parts
PRODUCT SAFETY NOTE: Products marked with a # have special characteristics important to safety. Before replacing any of these components, read carefully the product safety notice in this service manual. Don't degrade the safety of the product through improper servicing.
NOTES:
1. Parts that are not assigned part numbers (---------) are not available.
2. Tolerance of Capacitors and Resistors are noted with the following symbols.
Different parts from the original model 46PFL3608/F7 (Serial No. : DS1)
C.....±0.25% D.....±0.5% F.....±1%
G.....±2% J......±5% K.....±10%
M.....±20% N.....±30% Z.....+80/-20%
Ref. No. Description Part No.
DIGITAL MAIN CBA UNIT A3AQ2MMA-004
CN3701 Not used
IC3001 IC MSD8200DS-S1 NSAA0RMST001
IC3002 IC 512MB DDR2 SDRAM K4T51163QJ-BCE7 NSCA0R0SM048
IC3006 IC 32M-BIT SERIAL FLASH MEMORY W25Q32FVSSIG
NSCA0R0ZM018
IC3009 IC RESET IC-PST8429UR QSCA0T0MM075
IC3019 IC USB HIGH-SIDE SW AP2151WG-7/SOT25/5PI
NSCA0TDES015
IC3101 Not used
IC3102 Not used
IC3103 Not used
IC3201 IC DC-DC CONVERTER MP1472GJC452Z NSCA0T09M021
IC3601 REGULATOR AP1117EG-13 NSCA0TDES012
IC3602 REGULATOR AP1117EG-13 NSCA0TDES012
IC3603 IC REGULATOR BD00IA5WEFJ-E2 QSCA0T0RM233
IC3605 IC DCDC CONVERTER RT8293ALZSP NSCA0T00B017
IC3607 Not used
IC3701 Not used
IC3801 IC D-CLASS AUDIO POWER AMPLIFI TPA3110D2PWPR
NSCA0T0TY073
IC3803 Not used
IC3901 REGULATOR AP1117EG-13 NSCA0TDES012
TU3001 Not used
TU3901 TUNER UNIT U9001UH U9001UH
IC3401 Not used
IC3402 Not used
POWER SUPPLY CBA A3AQ0MPW-002
Q657 TRANSISTOR 2SA950-O (TE2 F T) QQS002SA950F
R685 RES CHIP 3216 1/4W J 3.3 Ω RRX43R3HH034
R686 RES CHIP 3216 1/4W J 3.3 Ω RRX43R3HH034
R687 RES CHIP 3216 1/4W J 3.3 Ω RRX43R3HH034
R688 RES CHIP 3216 1/4W J 2.2 Ω RRX42R2HH034
R689 RES CHIP 3216 1/4W J 2.7 Ω RRX42R7HH034
2013/05/21 13-21 A3AQCCA.fm
TYPE B
PARTS LIST [46PFL3708/F8 (Serial No.: XA1)]
Mechanical Parts
PRODUCT SAFETY NOTE: Products marked with a # have special characteristics important to safety. Before replacing any of these components, read carefully the product safety notice in this service manual. Don't degrade the safety of the product through improper servicing.
NOTE: Parts that are not assigned part numbers (---------) are not available.
Different parts from the original model 46PFL3608/F7 (Serial No. : DS1)
Ref. No. Description Part No.
A3 REAR COVER A3AU0UH 1EM030226
A13 JACK HOLDER A3AU0UH 1EM334651
A15# RATING LABEL A3AQCMA ----------
A16 LOGO LABEL A3AQZUH ----------
A17 Not used
CL3013 FFC WIRE ASSEMBLY 51PIN W/SHIELD 51PIN/457MM
WX1A3AQ0P401
CL3701 FFC WIRE ASSEMBLY 23PIN 23PIN/WHITE/205MM
WX1A3AU0S103
SBA1 50W STAND BASE ASSEMBLY (PF) A21U2UD 1EMN29164
SNA1 50W STAND HINGE ASSEMBLY (PF) A21U2UD 1EMN29163
S1 CARTON A3AQCMA 2EMC00134
S12 CARTON LABEL A3AQCMA ----------
X2# OWNERS MANUAL A31TAMA 1EMN30390
X3 REMOTE CONTROL UNIT YKF335-001 URMT39JHG001
X6 QUICK START GUIDE A31TAMA 1EMN30391
X22 WARNING MESSAGE FLIER A3AU2UH 2EMN00059A
2013/05/21 13-22 A3AQCEL.fm
Electrical Parts
PRODUCT SAFETY NOTE: Products marked with a # have special characteristics important to safety. Before replacing any of these components, read carefully the product safety notice in this service manual. Don't degrade the safety of the product through improper servicing.
NOTES:
1. Parts that are not assigned part numbers (---------) are not available.
2. Tolerance of Capacitors and Resistors are noted with the following symbols.
Different parts from the original model 46PFL3608/F7 (Serial No. : DS1)
C.....±0.25% D.....±0.5% F.....±1%
G.....±2% J......±5% K.....±10%
M.....±20% N.....±30% Z.....+80/-20%
Ref. No. Description Part No.
DIGITAL MAIN CBA UNIT A3AQCMMA-003
CN3701 Not used
IC3001 IC MSD8200DS-S1 NSAA0RMST001
IC3002 IC 512MB DDR2 SDRAM K4T51163QJ-BCE7 NSCA0R0SM048
IC3006 IC 32M-BIT SERIAL FLASH MEMORY W25Q32FVSSIG
NSCA0R0ZM018
IC3009 IC RESET IC-PST8429UR QSCA0T0MM075
IC3019 IC USB HIGH-SIDE SW AP2151WG-7/SOT25/5PI
NSCA0TDES015
IC3101 Not used
IC3102 Not used
IC3103 Not used
IC3201 IC DC-DC CONVERTER MP1472GJC452Z NSCA0T09M021
IC3601 REGULATOR AP1117EG-13 NSCA0TDES012
IC3602 REGULATOR AP1117EG-13 NSCA0TDES012
IC3603 IC REGULATOR BD00IA5WEFJ-E2 QSCA0T0RM233
IC3605 IC DCDC CONVERTER RT8293ALZSP NSCA0T00B017
IC3607 Not used
IC3701 Not used
IC3801 IC D-CLASS AUDIO POWER AMPLIFI TPA3110D2PWPR
NSCA0T0TY073
IC3803 Not used
IC3901 REGULATOR AP1117EG-13 NSCA0TDES012
TU3001 Not used
TU3901 TUNER UNIT U9001UH U9001UH
IC3401 Not used
IC3402 Not used
POWER SUPPLY CBA A3AQ0MPW-002
Q657 TRANSISTOR 2SA950-O (TE2 F T) QQS002SA950F
R685 RES CHIP 3216 1/4W J 3.3 Ω RRX43R3HH034
R686 RES CHIP 3216 1/4W J 3.3 Ω RRX43R3HH034
R687 RES CHIP 3216 1/4W J 3.3 Ω RRX43R3HH034
R688 RES CHIP 3216 1/4W J 2.2 Ω RRX42R2HH034
R689 RES CHIP 3216 1/4W J 2.7 Ω RRX42R7HH034
14-1 PL13.14REV
REVISION HISTORY
Chassis PL13.14• 2013/02/21 46PFL3608/F7 (Serial No.: DS1) added
• 2013/03/29 46PFL3908/F7 (Serial No.: DS1) added
• 2013/03/29 46PFL3708/F7 (Serial No.: DS1) added
• 2013/05/31 46PFL3708/F8 (Serial No.: XA1) added
• 2013/06/19 46PFL3908/F8 (Serial No.: XA1) added
• 2013/12/28 46PFL3608/F7 (Serial No.: DS2) added
• 2013/12/28 46PFL3908/F7 (Serial No.: DS2) added
• 2014/01/30 46PFL3908/F8 (Serial No.: XA2) added
• 2014/02/24 46PFL3608/F7 A (Serial No.: DS3) First draft added
PL13.14COM
COMPARISON LIST OF MODEL NAMES
Chassis PL13.1446PFL3608/F7 (DS1) A37QAUH TYPE A
(DS2) A37QCUH TYPE A
46PFL3908/F7 (DS1) A37Q0UH TYPE A
(DS2) A37QDUH TYPE A
46PFL3908/F8 (XA1) A37QBMA TYPE A
(XA2) A37QEMA TYPE A
46PFL3708/F7 (DS1) A3AQ2UH TYPE B
46PFL3708/F8 (XA1) A3AQCMA TYPE B
46PFL3608/F7 A (DS3) A37QFUH TYPE A