14

15

9

8

10

7

6

4

11

12

13

16

5

1 2 3• Models are hazardous when operated and maintained incorrectly. • Always install and operate a radio control system correctly. • Always pilot a model so the model is kept under control in all

conditions. • Please seek help from an experienced pilot or your local hobby

store. • Contact local or regional modeling organizations for guidance and

instructions about fl ying in your area. • When working with a model, always power on the transmitter fi rst

and power off the transmitter last. • After a model is bound to a transmitter and the model is set up in

the transmitter, always bind the model to the transmitter again to establish failsafe settings.

• Always make sure all batteries are fully charged before fl ying. • Time fl ights so you can fl y safely within the time allotted by your

battery.• Perform a range check of the transmitter and the model before

fl ying the model. • Make sure all control surfaces correctly respond to transmitter

controls before fl ying. • Do NOT fl y a model near spectators, parking areas or any other

area that could result in injury to people or damage to property.• Do NOT fl y during adverse weather conditions. Poor visibility, wind,

moisture and ice can cause pilot disorientation and/or loss of control of a model.

• When a fl ying model does not respond correctly to controls, land the model and correct the cause of the problem.

Age Recommendation:Not for children under 14 years. This is not a toy.

WARNING: Read the ENTIRE instruction manual to become familiar with the features of the product before operating. Failure to operate the product

correctly can result in damage to the product, personal property and cause serious injury.

This is a sophisticated hobby product. It must be operated with caution and common sense and requires some basic mechanical ability. Failure to operate this Product in a safe and responsible manner could result in injury or damage to the product or other property. This product is not intended for use by children without direct adult supervision. Do not use with incompatible components or alter this product in any way outside of the instructions provided by Horizon Hobby, LLC. This manual contains instructions for safety, operation and maintenance. It is essential to read and follow all the instructions and warnings in the manual, prior to assembly, setup or use, in order to operate correctly and avoid damage or serious injury.

The following terms are used throughout the product literature to indicate various levels of potential harm when operating this product:

NOTICE: Procedures, which if not properly followed, create a possibility of physical property damage AND a little or no possibility of injury.

CAUTION: Procedures, which if not properly followed, create the probability of physical property damage AND a possibility of serious injury.

WARNING: Procedures, which if not properly followed, create the probability of property damage, collateral damage, and serious injury OR create a high probability of superfi cial injury.

NOTICE

All instructions, warranties and other collateral documents are subject to change at the sole discretion of Horizon Hobby, LLC. For up-to-date product literature, visit horizonhobby.com and click on the support tab for this product.

Meaning of Special Language

WARNING: Failure to exercise caution while using this product and comply with the following warnings could

result in product malfunction, electrical issues, excessive heat, FIRE, and ultimately injury and property damage.

• Read all safety precautions and literature prior to use of this product• Never allow minors to charge battery packs• Never drop charger or batteries• Never attempt to charge damaged batteries• Never attempt to charge a battery pack containing different types

of batteries• Never charge a battery if the cable has been pinched or shorted• Never allow batteries or battery packs to come into contact with

moisture at any time• Never charge batteries in extremely hot or cold places (recom-

mended between 50–80 degrees F or 10–27 degrees C) or place in direct sunlight

• Always disconnect the battery after charging, and let the charger cool between charges

• Always inspect a new battery before charging• Always terminate all processes and contact Horizon Hobby if the

product malfunctions• Always keep batteries and charger away from any material that

could be affected by heat (such as ceramic and tile), as they can get hot

• Always end the charging process if the charger or battery becomes hot to the touch or starts to change form (swell) during the charge process

Charging Warnings

General Notes

Pilot Safety

www.KnowChroma.comBLH8645

M A N U A LW I Z A R D

1. Aircraft Mode LED2. Wizard GPS LED3. Aircraft Status LED4. Ascend / Forward Button5. Rotate / Fly Left Button6. Rotate / Fly Right Button7. Descend / Backward Button8. Magic Button

9. Camera Tilt Down10. Camera Tilt Up11. Start / Stop Motors Button12. Wizard Power Button13. Wizard Power LED14. Smart / AP / Home Mode

Switch15. Clip16. USB Port

Control Layout

Specifi cations

LED Codes

Aircraft Mode LED

Smart Mode: LED solid green

AP Mode: LED solid purple

Home Mode: LED solid red

‘Point-N-Fly’ Function Activated: LED solid blue

‘Follow Me’ Function Activated: LED solid yellow

Wizard GPS LED

GPS Locked: LED solid green

Aircraft Status LED

Wizard not bound: LED solid red

GPS Loss of Aircraft: LED off

Battery full: LED solid green

Battery 50%: LED blinking green twice every 2 seconds

Battery 25%: LED blinking green once every 2 seconds

Low Voltage Warning of the Aircraft:LED blinking red quickly, the Wizard vibratesfor 2 seconds

Wizard Power LED:

Powered On: LED solid green

During Charging: LED solid red

Charging Completed: Red LED off

Low Voltage Warning of the Wizard:

Low Battery: LED blinking green twice every 2 seconds

Low Voltage: LED blinking green once every 2 seconds

Power Cut-off: LED blinking red quickly, the Wizard vibrating for 2 seconds once continuously.

Dimensions: 5.47 X 1.46 X 0.98 in (139 X 37 X 25 mm)Weight: 2.52 oz (71.5 g)Built-In LiPo Battery Voltage/Capacity: 3.7V 500mAhApproximate Working Time: 3.5 hCompatible Aircfraft*: Blade® Chroma™

Compatible Camera: CGO2, CGO2+, CGO3Water Resistant: Yes

* This transmitter is not compatible with Spektrum DSM®, DSM2® or DSMX® technology equipped aircraft.

This transmitter is not compatible with Spektrum DSM®, DSM2® or DSMX® technology equipped aircraft.

©2015 Horizon Hobby, LLC.Blade, Chroma, DSM, DSM2, DSMX, Point-N-Fly and the Horizon Hobby logo are trademarks or registered trademarks of Horizon Hobby, LLC.The Spektrum trademark is used with permission of Bachmann Industries, Inc.Created 09/15 51112 (EN) BLH8645

Three fl ight modes are available using the Wizard, Smart Mode, Angle (AP) Mode and Home Mode.To change fl ight modes, change the position of the fl ight mode slider to the desired fl ight mode.Smart ModeThe aircraft mode LED glows solid green. While in Smart Mode, the quadcopter isgeo-fenced to no further than 300 feet(90 meters) away from the Wizard.While in Smart Mode, the fl ight controls function relative to the pilot position.Point-N-Fly™ Function

NOTICE: The recommended fl ying height is 10-20m. The operating range of the Wizard is 10-50m.This function is only available while Smart Mode is enabled.Point the Wizard in the direction you wish the quadcopter to fl y.Press and hold the Magic Button until the Aircraft Mode LED glows solid blue and the wand vibrates once.Tilt the wand from 0° – 90° to control the distance away desired. The closer to 0°, the farther away from you the quadcopter will travel. The closer to 90°, the closer to you the quadcopter will travel. When the wand is held at 90°, the quadcopter will fl y close to you and hold at a safe distance.To exit Point-N-Fly, press any direction control button. The quadcopter will stop moving and hold its position, if a suitable GPS signal is held, and maintain a level attitude.

Tracking FunctionTracking enables the camera to track the position of the Wizard, adjusting the tilt angle of the gimbal and the yaw of the quadcopter to keep the wand position in frame. The Rotate Left and Rotate Right functions are disabled while the Tracking function is active, however the Fly Left and Fly Right functions are still available.Tracking is the default function while in Smart Mode.To return to the Tracking Function from the Follow Me Function, press the Magic Button once. The Aircraft Mode LED will glow solid green.

Follow Me FunctionWith the Follow Me Function enabled, the quadcopter will follow the movement of the Wizard. To enable the Follow Me function, press the Magic Button quickly once. The Aircraft Mode LED will glow solid yellow, indicating Follow Me is enabled. All controls function normally while the Follow Me function is enabled. You must use the fl ight controls to keep the camera oriented in the desired direction.

CAUTION: The maximum fl ight speed of the Chroma™ quadcopter is approximately 18 mph.

If the movement of the pilot and Wizard exceeds 30 mph, the aircraft may crash or experience a “fl y away,” neither of which are covered under warranty.

Angle Mode (AP Mode)The aircraft mode LED glows solid purple.While in Angle Mode (AP Mode), the fl ight controls function relative to the quadcopter’s orientation. Point to Fly, Watch Me and Follow Me functions are disabled while Angle Mode is active.NOTICE: Do not allow the quadcopter to travel farther than 200m from the Wizard. If the aircraft exceeds 200m away, the Wizard will vibrate until the quadcopter is fl own back to within 200m.

Charge the Wizard (~2 hours)

Powering On the Wizard

Binding the Wizard to the Chroma

Flight Controls

Flight Modes

Starting and Stopping the Motors

Calibration Procedures

Troubleshooting

CAUTION: Refer to the Charging Warnings section. All instructions and warnings must be followed

exactly. Mishandling of Li-Po batteries can result in a fi re, personal injury and/or property damage.

Power off the Wizard. Using the USB cable provided, connect the Wizard to a suitable USB power source.Power LED Indications

Power On: Solid GreenCharging: Solid RedCharging Complete: Off

NOTICE: Storing the fully charged Wizard for extended periods of time may damage the installed LiPo battery. The wand should be stored in a partially discharged state.NOTICE: Do not remove the installed LiPo battery. Battery removal may damage the wand and will void the warranty.

Press and hold the Power Button. When the LEDs blink once and the Wizard vibrates once, release the Power button. The Power LED glows solid green, and the Aircraft Mode LED is on, showing the currently selected fl ight mode color.

The Wizard must be bound to the Chroma quadcopter for proper operation. To bind or re-bind your quadcopter to Wizard, follow the directions below.1. With the transmitter and quadcopter powered OFF, connect

the battery to the quadcopter.2. Place the quadcopter on a fl at level surface.3. Power the quadcopter ON and let it initialize. The status

LEDs will remain off.4. Hold the quadcopter upside down until the status LEDs fl ash

blue, indicating it has entered bind mode.5. Set the quadcopter back

upright.6. Press and hold the Wizard

power button until the Aircraft Mode LED glows solid blue.

7. Shake the Wizard up and down as shown until the quadcopter beeps twice, indicating binding is successful.

8. Release the power button.

The Wizard controls different aspects of the quadcopter’s fl ight by changing the orientation of the wand.

Holding the wand between 50° and 90°, as shown, enables the control functions shown below:

Push and hold the Motor Start/Stop button to start the motors. When you have completed your fl ight, you may either use Home Mode to land and stop the motors, or land manually and press the Motor

Start/Stop button after the quadcopter is on the ground.If the quadcopter is below 20 ft above the Wizard, hold the stop button for 1.5 seconds to stop the motors.If the quadcopter is above 20 ft above the Wizard, hold the stop button for 3 seconds to stop the motors.

NOTICE: Do not press the Motor Stop button while the aircraft is airborne. The motors could stop, causing the aircraft to crash.

WARNING: Stopping the motors while the quadcopter is still in fl ight will cause the quadcopter to crash.

Crash damage is not covered under warranty.

90°50°

0°

90°40°

0°

Holding the wand between 0° and 40°, as shown, enablesthe control functions shown below:

Ascend

Fly forward

Descend

Fly backward

Rotate right

Fly right

Rotate left

Fly left

Home ModeThe Aircraft Mode LED glows solid red.When Home Mode is activated, the quadcopter will fl y in a straight line in the direction of the pilot. If the quadcopter is below 30 ft when Home Mode is activated, it will climb above 30 ft prior to returning to the pilot. The quadcopter will return to within 4-8m from the pilot, land and stop the motors. Pay attention to the prospective landing area when the quadcopter begins its descent. The fl y forward, fl y backward, fl y left and fl y right buttons may be used, while the quadcopter is descending, to re-position it to a safe landing area if needed. NOTICE: During the controlled descent, the fl ight controls function relative to the quadcopter’s orientation, similar to Angle Mode.

Point-N-Fly, Tracking and Follow Me functions are disabled while Home Mode is active.To exit Home Mode before the quadcopter lands, change the fl ight mode slider to Smart or Angle (AP) Mode. The quadcopter will stop and hold its position, if it has a suitable GPS lock, and maintain a stable attitude.

CAUTION: Do not activate Home Mode if you are in or near a body of water.

The tilt angle of the camera gimbal is controlled using the Camera Tilt buttons on the Wizard.Photo and video functions are

controlled using your smart device via the mobile application available from Google Play or the App Store.

NOTICE: The control radius of the camera, under ideal conditions, is approximately 90m.

Problem Solution

Wizard vibrates continu-ously afterpowering on

Contact customer service

Wizard fails to power on Contact customer serviceAircraft Status LED is solid yellow or blinking yellowfrequently

Follow the calibrationprocedures to calibrate the Wizard

Power LED fl ashes red rapidly

Low battery – Follow thecharging procedure to re-charge the Wizard

For a complete description of the function, capabilitiesand maintenance of the Wizard, refer to the online videos at www.KnowChroma.com.

NOTICE: Magnetic interference may affect the calibration procedure. It is recommended to calibrate the Wizard outdoors, away from any magnetic surface.

To enter calibration mode:Press and hold both the Descend/Backward Button and the Power Button together until the Aircraft Status LED is solid pink, approximately 2 seconds.Release both buttons. If for any reason the Wizard does not enter calibration mode successfully, power it off and back on again and attempt to enter calibration mode again.When the Wizard has successfully entered calibration mode, hold it at arms length with the buttons facing toward your body and move it in a horizontal fi gure-eight continuously, as shown in the illustration, rotating the Wizard to follow the path. While following the fi gure-eight with the Wizard, rotate your body slowly in a circle. This process should take approximately30 seconds.When the calibration process is complete, the Wizard will automatically power off. The Wizard is now calibrated and may be powered on and used normally.If the calibration process fails, the Aircraft Mode LED will glow solid red and the power LED will rapidly fl ash red. Power the Wizard off and repeat the calibration process until successful.For further information on calibrating the Wizard, see the online videos at www.KnowChroma.com.

Camera Control