A.G. Andreou 2000 1
520/580.495
Film Deposition
Andreas G. Andreou
Lecture notes from
Physical Vapor Deposition by R. Darling
http://www.engr.washington.edu/~cam/PROCESSES/physicalvapdeppdf.html
A.G. Andreou 2000 2
OUTLINE
• Thin film deposition methods• Evaporation• Physics and simple model
A.G. Andreou 2000 3
METHODS
• Evaporation– Thermal (Filament)– Electron-beam– Flash
• Sputtering• Chemical Vapor Deposition (CVD)
– Low Pressure (LPCVD)– Plasma Enhanced (PECVD)
• Epitaxy– Vapor Phase (VPE)– Liquid Phase (LPE)– Molecular Beam (MBE)
• Conductors - metal films, polysilicon• Insulators – dielectrics Si02• Semiconductors – GaAs …
A.G. Andreou 2000 4
EVAPORATION
R. B. Darling / EE-527
Evaporation System Requirements
• Vacuum:– Need 10-6 torr for medium quality films.– Can be accomplished in UHV down to 10-9 torr.
• Cooling water:– Hearth– Thickness monitor– Bell jar
• Mechanical shutter:– Evaporation rate is set by temperature of source, but this cannot be
turned on and off rapidly. A mechanical shutter allows evaporantflux to be rapidly modulated.
• Electrical power:– Either high current or high voltage, typically 1-10 kW.
R. B. Darling / EE-527
Evaporation Support Materials
• Refractory metals:– Tungsten (W); MP = 3380°C, P* = 10-2 torr at 3230°C– Tantalum (Ta); MP = 3000°C, P* = 10-2 torr at 3060°C– Molybdenum (Mo); MP = 2620°C, P* = 10-2 torr at 2530°C
• Refractory ceramics:– Graphitic Carbon (C); MP = 3700°C, P* = 10-2 torr at 2600°C– Alumina (Al2O3); MP = 2030°C, P* = 10-2 torr at 1900°C– Boron nitride (BN); MP = 2500°C, P* = 10-2 torr at 1600°C
• Engineering considerations:– Thermal conductivity– Thermal expansion– Electrical conductivity– Wettability and reactivity
R. B. Darling / EE-527
Resistance Heated Evaporation
• Simple, robust, and in widespread use.• Can only achieve temperatures of about 1800°C.• Use W, Ta, or Mo filaments to heat evaporation source.• Typical filament currents are 200-300 Amperes.• Exposes substrates to visible and IR radiation.• Typical deposition rates are 1-20 Angstroms/second.• Common evaporant materials:
– Au, Ag, Al, Sn, Cr, Sb, Ge, In, Mg, Ga– CdS, PbS, CdSe, NaCl, KCl, AgCl, MgF2, CaF2, PbCl2
R. B. Darling / EE-527
Resistance Heated Evaporation Sources
wire hairpin
wire helix
wire basket
foil dimple boat
foil trough
alumina coated foil dimple boat
alumina crucible with wire basket
chromium coated tungsten rod
alumina crucible in tantalum box
R. B. Darling / EE-527
Electron Beam Heated Evaporation - 1
• More complex, but extremely versatile.• Can achieve temperatures in excess of 3000°C.• Use evaporation cones or crucibles in a copper hearth.• Typical emission voltage is 8-10 kV.• Exposes substrates to secondary electron radiation.
– X-rays can also be generated by high voltage electron beam.
• Typical deposition rates are 10-100 Angstroms/second.• Common evaporant materials:
– Everything a resistance heated evaporator will accommodate, plus:– Ni, Pt, Ir, Rh, Ti, V, Zr, W, Ta, Mo– Al2O3, SiO, SiO2, SnO2, TiO2, ZrO2
R. B. Darling / EE-527
Electron Beam Heated Evaporation Source
4-pocket rotarycopper hearth
(0 V)
pyrolytic graphitehearth liner
recirculatingcooling water
evaporation conesof material
cathodefilament
(-10,000 V)
beam formingaperture
270 degree bentelectron beam
magneticfield
R. B. Darling / EE-527
Electron Beam Heated Evaporation - 2
• 270° bent beam electron gun is most preferred:– Filament is out of direct exposure from evaporant flux.– Magnetic field can be used for beam focusing.– Magnetic field can be used for beam positioning.– Additional lateral magnetic field can be used produce X-Y sweep.
• Sweeping or rastering of the evaporant source is useful for:– Allows a larger evaporant surface area for higher deposition rates.– Allows initial charge to be “soaked” or preheated.– Allows evaporant source to be more fully utilized.
• Multiple pocket rotary hearth is also preferred:– Allows sequential deposition of layers with a single pump-down.– Allows larger evaporation sources to be used.
A.G. Andreou 2000 5
PHYSICS AND MODELS
(First order effects)
R. B. Darling / EE-527
Physical Vapor Deposition
Gas Phase Gas Phase
Condensed Phase(solid or liquid)
Condensed Phase(usually solid)
Evaporation
Transport
Condensation
R. B. Darling / EE-527
Equilibrium Vapor Pressure
• P* is the partial pressure of a gas in equilibrium with itscondensed phase at a given temperature T.– No net transfer of material from one state to the other.
• For a given material, P* is only a function of T.– But the dependence of P* on T is rather complicated.
R. B. Darling / EE-527
Evaporation Rates - 1
• P* is the equilibrium vapor pressure of the evaporant at T.• P is the ambient hydrostatic pressure acting upon the
evaporant in the condensed phase.• Heinrich Hertz found experimentally that the evaporation
rate was proportional to (P* - P).– This is consistent with kinetic theory in which the impingement
rates are proportional to pressure.– Hertz also found that the evaporation rate could not be increased
by supplying more heat unless the equilibrium vapor pressure wasalso increased by this action.
– Thus, there is a maximum evaporation rate set by P*, and this isonly achieved in a vacuum, where P = 0.
R. B. Darling / EE-527
Evaporation Rates - 2
• This can be viewed as two opposing fluxes:
evaporant vapor
condensed evaporant
The net evaporation flux is the differencebetween the impingement rates for thetwo fluxes:
( ) ( )PPTmkdtA
dNB
e
e −= − *2/12πrate goes as P
rate goes as P*
R. B. Darling / EE-527
Evaporation Rates - 3
• Hertz only measured rates of about 1/10 of the above usingHg vapor.
• Knudsen postulated that the evaporant vapor moleculesimpinging upon the condensed phase surface may bereflected back.– α v = sticking coefficient for vapor molecules onto the surface.– Then a (1 - α v) fraction of the vapor molecules contribute to the
evaporant pressure, but not to the evaporant flux.– Therefore, the vapor pressure must be higher by a factor of 1/α v to
obtain the same evaporation rate.
• This gives the general Hertz-Knudsen equation:
( ) ( )PPTmkdtA
dNBv
e
e −= − *2/12πα
R. B. Darling / EE-527
Mass Evaporation Rates
• Γ = mass evaporation rate in g/cm2-sec:
• For most elements, Γ ~ 10-4 g/cm2-sec at P* = 10-2 torr.• The mass of the evaporated material is
( )PPTk
mdtA
dNm
Bv
e
e −
==Γ *
2/1
2πα
∫∫Γ=t A
ee
e
dtdAM0 0
R. B. Darling / EE-527
Free Evaporation Versus Effusion
• Evaporation from a free surface is termed Langmuirevaporation.
• Because α v is often much less than unity, the generalHertz-Knudsen expression must be used.
• Effusion refers to evaporation through an orifice by whichthe area of the orifice appears as an evaporation source ofthe same area.
• Free evaporation is isotropic.• Effusion is somewhat directional.
– Ideally, it is a Lambertian angular distribution.
R. B. Darling / EE-527
Equilibrium Vapor Pressure
• A working formulation of the equilibrium vapor pressurefrom standard thermochemical data is therefore:
– P* is in units of atmospheres.– ∆ Heo(298K), ∆ Seo(298K), and cp(T) may be found in standard
tables of thermochemical data.– Note: 1 kcal = 1 Cal = 1000 cal = 4186.8 J = 3.97 BTU– See Section D of the CRC Handbook of Chemistry and Physics.– Example: Aluminum:
• ∆ Heo(298K) = 70 kcal/mole, ∆ Seo(298K) = 30 kcal/mole-K, at theboiling point of P = 1 atm and T = 2327°C = 2600 K.
• ∆ Hmo(298K) = 2.57 kcal/mole, at the melting point of P = 1 atm and T= 658.5°C = 931.7 K.
∫ ∫∆
+∆+∆−=T
K
T
K
peoeo dTdTTc
RTRKS
RTKH
P298 298
* 1)298()298(ln
R. B. Darling / EE-527
Equilibrium Vapor Pressure
1.00E-11
1.00E-10
1.00E-09
1.00E-08
1.00E-07
1.00E-06
1.00E-05
1.00E-04
1.00E-03
1.00E-02
1.00E-01
1.00E+00
1.00E+01
1.00E+02
1.00E+03
0 1000 2000 3000 4000 5000
Temperature, K
Vapo
r Pre
ssur
e, T
orr
Aluminum
Gallium
Indium
Silicon
Gold
Platinum
Chromium
Titanium
R. B. Darling / EE-527
Equilibrium Vapor Pressure
1.00E-11
1.00E-10
1.00E-09
1.00E-08
1.00E-07
1.00E-06
1.00E-05
1.00E-04
1.00E-03
1.00E-02
1.00E-01
1.00E+00
1.00E+01
1.00E+02
1.00E+03
0 5 10 15 20
Reciprocal Temperature, 10000/T(K)
Vapo
r Pre
ssur
e, T
orr
Aluminum
Gallium
Indium
Silicon
Gold
Platinum
Chromium
Titanium
R. B. Darling / EE-527
Adsorption
• Adsorption is the sticking of a particle to a surface.• Physisorption:
– The impinging molecule loses kinetic (thermal) energy withinsome residence time, and the lower energy of the molecule doesnot allow it to overcome the threshold that is needed to escape.
• Chemisorption:– The impinging molecule loses its kinetic energy to a chemical
reaction which forms a chemical bond between it and othersubstrate atoms.
R. B. Darling / EE-527
Condensation of Evaporant - 1
• Condensation of a vapor to a solid or liquid occurs whenthe partial pressure of the vapor exceeds the equilibriumvapor pressure of the condensed phase at this temperature.
• The vapor is “supersaturated” under these conditions.• This is only true if condensation takes place onto material
which is of the same composition as the vapor.• When a material is first deposited onto a substrate of a
different composition, a third adsorbed phase must beincluded to describe the process.
R. B. Darling / EE-527
Condensation of Evaporant - 2
• Molecules impinging upon a surface may:– Adsorb and permanently stick where they land (rare!).– Adsorb and permanently stick after diffusing around on the surface
to find an appropriate site.• This can lead to physisorption or chemisorption.
– Adsorb and then desorb after some residence time τa.– Immediately reflect off of the surface.
• Incident vapor molecules normally have a kinetic energymuch higher than kBT of the substrate surface.
• Whether an atom or molecule will stick depends upon howwell it can equilibrate with the substrate surface,decreasing its energy to the point where it will notsubsequently desorb.
R. B. Darling / EE-527
Condensation of Evaporant - 3
• Thermal accomodation coefficient:
– Ev, Tv = energy, temperature of impinging vapor molecules.– Er, Tr = energy, temperature of resident vapor molecules;
• (Those which have adsorbed, but have not permanently found a site.)– Es, Ts = energy, temperature of substrate surface.
• If α T < 1, (Er > Es), then some fraction of the impingingmolecules will desorb from the surface.
sv
rv
sv
rvT TT
TTEEEE
−−=
−−=α
R. B. Darling / EE-527
Condensation of Evaporant - 4
• Mean residence time for an adsorbed molecule:
– υ 0 = kBT/h = vibrational frequency of adsorbed molecule (~1014 Hz)• This is the frequency at which the molecule “attempts” to desorb.
– ∆ Gdes = free activation energy for desorption.
• Under a constant impinging vapor flux of R, the surfacedensity of the deposit is then:
– R = deposition rate in molecules/cm2-sec.– ns = surface density of deposited molecules in cm-2.
∆=
TG
aB
des
0 kexp1
υτ
∆==
TGRRn asB
des
0 kexp
υτ
R. B. Darling / EE-527
Condensation of Evaporant - 5
• If the impingement rate stops, then the adsorbed moleculeswill all eventually desorb.
• Condensation of a permanent deposit will not occur, evenfor low substrate temperatures, unless the moleculesinteract.
• Within the mean residence time, surface migration occursand clusters form.
• Clusters have smaller surface-to-volume ratios, andtherefore desorb at a reduced rate.
• Nucleation of a permanent deposit is therefore dependentupon clustering of the adsorbed molecules.
R. B. Darling / EE-527
Stages of Thin Film Growth
• Island Stage• Coalescence Stage• Channel Stage• Continuous Film Stage
R. B. Darling / EE-527
Modes of Thin Film Growth
(1) Volmer-Weber: (island growth):
(2) Frank-Van der Merwe: (layer growth; ideal epitaxy):
(3) Stranski-Krastanov: (layers + islands):
M. Volmer and A. Weber, Z. Phys. Chem. 119, p. 277 (1926).
F. C. Frank and J. H. Van der Merwe, Proc. R. Soc. London, Ser. A 198, p. 205 (1949).
J. N. Stranski and L. Krastanov, Ber. Akad. Wiss. Wien 146, p. 797 (1938).
R. B. Darling / EE-527
Condensation Control
• Control of condensation of the evaporant is achievedthrough the control of substrate temperature Ts.
• Higher substrate temperatures:– Increase thermal energy of adsorbed molecules.
• (Shortens the residence time.)– Increase surface diffusivity of adsorbed molecules.– Performs annealing of deposited film.
• Substrate heaters:– Quartz IR lamps from frontside– Ta, W, or Mo foil heaters from backside– Graphite impregnated cloth heaters from backside
• Too much heat will desorb the deposited film, evaporatingit away! (But this can be used for cleaning… )