6” Stainless Steel Wiped-Film Evaporation Plant
BW-WFE-6-SS
6” Stainless Steel Wiped-Film Evaporator
• Delivers greater consistency, purity, and confidence in every cannabis oil distillation.
• Continuous flow leaves behind less advanced and efficient methods with a dependable input up to 7 liters per hour.
www.beakerandwrench.com 213-265-7744 [email protected]
6” Stainless Steel Wiped-Film Evaporator
Throughput capability• Up to 7.0 L/hr• Average 3.0-5.0 L/hr
True Continuous Feed • Peristaltic Inlet pump allows addition of oil while machine is still under vacuum• Outlet pumps allow dispensing of products directly into vessel of choice• Feed rates adjustable from 10mL to 10L/hr
Jacketed body• Thermal fluid circulating through jacketed body for consistent temperature
Precise temperature control• PID temperature controllers on body and all heated lines for creation of precise SOPs
Expert On-Site Training and Installation • Validation with YOUR oil on the day of install• Consultation on how to generate the best SOP for your lab• Sample SOP provided for internal use
Potency up to 99.8% total cannabinoid content
www.beakerandwrench.com 213-265-7744 [email protected]
Specifications
Feed
• 5L or 20L stainless steel feed flask with vacuum inlet line• Peristaltic dosing pump for precise, vacuum-held dosing• Feed line to evaporator is jacketed and PID controlled
Short-Path Evaporator • Max evaporator temperature: 200 °C • 316 Stainless Steel• 316 Stainless Steel Internal condenser (cold finger)• 6 rollers• Easy to adjust drive system speed
Distillate & Residue Discharge Pumps (2 pumps)
• Gear pump in PID controlled heated design (design temperature 100°C), digitally displayed pump speed. Calibration and secret menu options for optimal SOP development
• Check valves used as a pressure lock against the atmosphere
Vacuum System • 21 to 36 CFM Rotary Vane Vacuum pump equipped with
vacuum pump oil• Diffusion vacuum pump for achieving stable vacuum
conditions at low pressures (oil included)• Flanged cold trap & collection vessel for cold trap
Heating & Cooling by Beaker & Wrench/ Polyscience
• 1 independent heating unit for the evaporator (oil circulator)• 1 independent heating unit (silicone pad) for the residue &
distillate line• 1 independent heating unit for the feed tank (silicone pad)• 1 independent cooling unit for the cold trap (immersion
probe)• 1 independent chilling unit for the internal condenser (water
circulator)
Rack/Frame
• Frame constructed of 80/20 aluminium extrusion and equipped with 4 wheels Power supply & power distribution system 1. Voltage: 120V or 220V
• Frequency: 60 Hz 3. Number of Phases: 1 (two hot wires) • Power distribution panel• Control panel for pumps. Included spare parts.• 1 set of rollers• 1 set of static gaskets • 1 set of shaft sealing for rotary transmission • 1 set of bearings for rotary transmission • 1 set of O-rings
Documentation• Operating instructions
Component Certifications See Below• Heaters & Chillers CE/ISO9001 • Vacuum Pumps • Gear Pumps • Wiper Drive • Power Box • Frequency Box • Pressure Gauge
www.beakerandwrench.com 213-265-7744 [email protected]
Vacuum Pump Motor (part 1)
Max. Ambient Temperature 40 Degrees CNominal Efficiency 82.4%Nameplate RPM 1725HP 2Overall Length 13-13/16"Phase 1Voltage Compatibility 115, 120, 208, 230, 240, 115/208-230, 115/230, 120/240, 208-230, 208-240Full Load Amps 18.8/10.2-9.4Motor Enclosure Design Totally Enclosed Fan-CooledMotor Design Capacitor-Start/RunNo. of Speeds 1Motor Bearings BallMotor Application General ApplicationIns. Class BFrame 56cMotor Service Factor 1.00Shaft Dia. 5/8”Manufacturers Warranty Length 1 yr.Duty ContinuousHz 60Motor Shaft Rotation CW/CCWVoltage 115/208-230Standards UL (E47479), CSA (258501)RPM Range 1701-1800RPM Group 1701-1800Footnotes 24,51Frame Material SteelMotor Mounting Type FaceLength Less Shaft 11-13/16”Motor Shaft Design Keyed
www.beakerandwrench.com 213-265-7744 [email protected]
Vacuum Pump Motor (part 2)
Motor Efficiency Group Energy EfficientShaft Length 1-7/8”Item General Purpose MotorMotor Thermal Protection None
www.beakerandwrench.com 213-265-7744 [email protected]
Gear, Peristaltic, Wiper Drive Power Supply
Power Supply Type SwitchingOutput Configuration Single outputOutput Voltage Range 24 VDC (adjustable)Amperage Rating: 10AOutput Power 240WNominal Input Voltage 120/240 VAC or 120-375 VDC Input Voltage Range 85-264 VAC / 120-375 VDC
UL Listed File #: E197592UL Recognized File #: E198298UL Hazardous File #: None
www.beakerandwrench.com 213-265-7744 [email protected]
Circulating Heaters
Model H5W/O H15W/O H25W/O H60W/OTiming Continuous operation or timing functionTemperature Range Room: +5 ~ 99(W)/200(O) °C Temperature Control Digital PID +/-0.1 °C, Touch Screen 7 inchPump Speed 0~20 (+/-10%) L/min, adjustableDrain Valve/Port W: Yes, O: NoTank Volume 5.0 L 15.0 L 25.0 L 60.0 LBath Opening 13x13 cm 24x16 cm 24x16 cm 30x28 cmTank Size (cm) 26x14x14 30x24x20 30x25x28 40x40x38 Heating Watts (W) 750W 1000W 1600W 5000WHeating Watts (O) 1000 W 1650 W 2400 W 8000WMax. Pressure 2.5 barProduct Size (cm) 40x35x45 42x45x51 42x45x58 60x60x75Product Weight 25/30 lbs 28/45 lbs 45/55 lbs 100/125 lbs
Tank Size (cm) 26x14x14 30x24x20 30x25x28 40x40x38Heating Watts (W) 750W 1000W 1600W 5000W Heating Watts (O) 1000 W 1650 W 2400 W 8000WAC Voltage & Amp (W/O) 110V 6.5/9.5A 220V 3.5/4.8A Max. Pressure 2.5 barProduct Size (cm) 40x35x45 42x45x51 42x45x58 60x60x75Product Weight 25/30 lbs 28/45 lbs 45/55 lbs 100/125 lbs
www.beakerandwrench.com 213-265-7744 [email protected]
Vacuum Gauge
Measurement Method Convection Enhanced PiraniMeasurement Range 1 x 10-4 to 1,000 Torr (1.3 x 10-4 to 1,333 mbar)Communications Interface RS-485/RS-232Temperature (Operating) 0-40° CTemperature (Storage) -40-70° CTemperature (Bakeout) 150° C (gauge only -- electronics removed)Display 4-digit OLED (user-selectable Torr, mbar, or Pa)Materials Exposed to Vacuum Gold-plated tungsten, 304 & 316 stainless steel, glass, nickel, PFPEAccuracy (Typical) 1.0x10-4 to 1.0x10-3 Torr; 0.1 mTorr resolution 1.0x10-3 to 400 Torr; ± 10% of reading 400 to 1,000 Torr; ± 2.5% of readingRepeatability (Typical) ± 2% of readingSet-Point Relays Two SPDT RelaysRelay Response 1A at 30 VDC resistive, or AC non-inductiveMounting/Installation Horizontal recommendedOrientation (Orientation has no effect below 1 Torr)Analog Outputs a) non-linear S-curve 0.375–5.659 VDC b) log-linear 1–8 VDC 1) V/decade 2) linear 0–10 VDC, user scalableInternal Volume 26 cm3 (1.589 in3)
Input Power 12-28 VDC, 2 W, protected against power reversal and transient over-voltages
Connections 9-pin sub-D (male) 15-pin high-density sub-D (male)Compliance & Standards CE compliant, RoHS compliant
www.beakerandwrench.com 213-265-7744 [email protected]
-80C Immersion Probe
Working Temperature Range °F -112° to -40°Working Temperature Range °C -80° to -40°Temperature Control (°F) Fixed at -112°Temperature Control (°C) Fixed at -80°CCleanable Air Filter YesDisplay TemperatureMaximum Ambient Temperature °F 86°Maximum Ambient Temperature °C 30°Overall Dimensions (L x W x H) (inches) 20.1 x 15 x 22.3 inOverall Dimensions (L x W x H) (cm) 51.1 x 38.1 x 56.6 cmRefrigerant R404A & R508BImmersion Probe Type Rigid CoilProbe Diameter (inches) 1.75Probe Diameter (cm) 4.44Probe Length (inches) Probe Length (inches)Probe Length (cm) Coil: 17.8 / Exposed: 41.9Flexible Hose Diameter (inches) 2.83Flexible Hose Diameter (cm) 7.14Flexible Hose Length (feet) 6Flexible Hose Length (m) 1.83Shipping Weight (pounds) 162.0Shipping Weight (kilograms) 73.5Catalog Page Number 114-115
www.beakerandwrench.com 213-265-7744 [email protected]
Wiper Drive Motor
Motor Frame Size NEMA 34 - 3.42 in (86.87 mm) sq.Length 4.63 in (117.60 mm)Input (bus) Voltage Range 24-75 VDC (90 VDC max)Peak Torque (@75 VDC) 605 oz-in (4.3 N-m)Cont. (RMS) Torque (@75 VDC) 141 oz-in (1.0 N-m)Max Speed (@75 VDC) 4150 RPMAchievable Resolution 0.450 degreesRepeatability 0.03 degreesShaft Diameter 0.50 in (12.70 mm)Weight 5.8 lb (2.6 kg)Rotor Inertia 11.4 oz-in² (2.1 kg-cm²)Logic Input Voltage Range 4.0 to 28 VDCMaximum Radial Load 50 lbf (222.4 N)Maximum Thrust Load 10.0 lbf (44.5 N) Environmental Rating Dust & water splash resistantAmbient Temperature 0-70 deg C (derated >40C)Ambient Humidity 0-95%; non-condensingRegulatory Certifications UL recognized; CE; RoHSCountry of Origin USA
www.beakerandwrench.com 213-265-7744 [email protected]
Wiper Drive (part 1)
Current at 5V 7.5mA (min.)Input Current at 28V 12.0mA (min.)HLFB Absolute Maximum Voltage 30VDC (across output terminals)HLFB Output Current, Maximum 9mA (non-inductive load)HLFB Output voltage drop @ 2mA 0.30VDC (+/- 100mV)HLFB Output voltage drop @ 5mA 0.55VDC (+/- 100mV)Motor Bearing, NEMA34:Maximum Radial Load, NEMA34 220N (50-lbs), applied 25mm (1.0in) from front bearingMaximum Thrust Load, NEMA34 44N (10-lbs)Bearing Life, NEMA34 revs (typ., load dependent.) 2.4 x109 to 5.3 x109
Motor Bearing, NEMA23:Maximum Radial Load, NEMA23 110N (25 lbs), applied 25mm (1.0in) from front bearingMaximum Thrust Load, NEMA23 22N (5 lbs)Bearing Life, NEMA23 3.2 x109 to 5.0 x109 revs (typ., load dependent.)Environmental:Shock (peak, maximum) 10G (applied no more than twice)Vibration (RMS, 2 Hz-200 Hz) 1.0G or 0.5mm, whichever is lessMaximum External Shaft Deceleration 250,000 rad/s2Maximum Ambient Operating Temp. For seasonal/intermittent duty 70°C/158°F (RMS torque output de-rated)For continuous long-term use 55°C/122°F (RMS torque output de-rated)For full-rated output speed/torque 40°C/104°FMaximum Body Temp. 100°CMaximum Rear Cover Temp. 70°CStorage Temperature -20°C to 85°CHumidity 0% to 95%, Non-CondensingRecommended Optional Fan, NEMA23 40mm square, 45.25 mm bolt center, >7CFM
www.beakerandwrench.com 213-265-7744 [email protected]
Wiper Drive (part 2)
Recommended Optional Fan, NEMA34 60mm square, 70.71 mm bolt center, >14CFMEnvironmental Sealing Front Face, with shaft seal option IP65Front Face, without shaft seal option IP53Body/rear, with dielectric sealing grease in connectors IP55Body/rear, no sealing provisions IP53ComplianceRegulatory Certifications UL recognized, CE, RoHSElectrical Safety UL508C, EN 61010-1EMI EN 61326-1Country of Origin USA
www.beakerandwrench.com 213-265-7744 [email protected]
Varian M-2 Water-Cooled Diffusion Pump
Operating Specifications:Optimum Operating Range 2 x 10^-3 torr to less than 3 x 10^-9 torrMaximum Pumping Speed 285 liters/second for airMaximum Forepressure no load: 5.5 x 10^-1 full load: 4.0 x 10^-1Maximum Throughput 0.5 torr liter/secondBackstreaming Rate at Pump Inlet 0.0009 mg/cm^2/min (with cold cap)Aprox. Power Required 450 wattsHeat-up Time 15 minCool-down Time less than 5 min to “break jet” less than 10 min to vent pumpFluid Charge 100cc. For all conventional/high performance pump fluidsCooling Water Requirements 0.1 gpm at 60 deg F to 80 deg F inlet tempFluid Charge 100cc. For all conventional/high performance pump fluidsBacking Pump Size Recommended 5 cfm or larger for optimum throughout
Physical Specifications:Inlet Flange ConnectionOD 6 inchesID 3 11/32 inchesThickness 1/2 inchBolt Circle 4 3/4 diameterNo. of HolesSize of Holes 3/4 diameterOrientation Straddle GLGasket Groove 3 15/32 ID x 13/64 wideGasket O-ring Parket #2-238 Butyl
www.beakerandwrench.com 213-265-7744 [email protected]
Diffusion Pump
Foreline ConnectionTubing 0.840 OD*Height 12 11/16 inch - allow additional 3 1/2” for heater removalJet Assembly self-aligning, fractionating design with 3 diffusion stages and one ejector stageForeline Baffle Stacked half moons with snap ring retainerCold Cap Conduction cooledWater Connections 1/8 FPT body and quick cool
Materials of ConstructionBody Stainless SteelFlange Mild SteelJet Assembly Stainless SteelForeline Baffle Stainless SteelCooling Coils Copper, welded to bodyHeater Reflector Polished AluminiumCold Cap Copper, Nickel Plated
Heater: Cartridge TypeSTD Voltage (nom.) 115V 1ΦOption (Nom.) 240V 1ΦPower 450 Watts (approx.)Connector Plug-in, 115V, mates with Hubbell #5269 ( 240V mates with Hubbel #5669)Exterior Finish GreenActual Weight 10 lbsShipping Weight 20 lbs0181-6473-02-150 Heater, 450W, 120V
www.beakerandwrench.com 213-265-7744 [email protected]