Gillette Generators, Inc. • 2921 Thorne Dr. •Elkhart, IN • 46514 • Ph: 574-264-9639 • Fax: 574-262-1840 • Web: www.gillettegenerators.com • spc4-190719 1 60 HZ MODEL SPJD-2100 LIQUID COOLED DIESEL ENGINE GENERATOR SET GENERATOR RATINGS GENERATOR MODEL VOLTAGE PH HZ 120°C RISE STANDBY RATING POWER LEAD CONNECTIONS L-N L-L KW/KVA AMP SPJD-2100-1-1 120 240 1 60 210/210 875 4 LEAD DEDICATED 1 PH SPJD-2100-3-2 120 208 3 60 210/262.5 729 12 LEAD LOW WYE SPJD-2100-3-3 120 240 3 60 210/262.5 632 12 LEAD HIGH DELTA SPJD-2100-3-4 277 480 3 60 210/262.5 316 12 LEAD HIGH WYE SPJD-2100-3-5 127 220 3 60 210/262.5 690 12 LEAD LOW WYE SPJD2100-3-16 346 600 3 60 210/262.5 252 4 LEAD DEDICATED 3 PH RATINGS: All single phase gen-sets are dedicated 4 lead windings, rated at unity (1.0) power factor. All three phase gen-sets are 12 lead windings, rated at .8 power factor. 120° C “STANDBY RATINGS” are strictly for gen-sets that are used for back-up emergency power to a failed normal utility power source. This standby rating allows varying loads, with no overload capability, for the entire duration of utility power outage. All gen-set power ratings are based on temperature rise measured by resistance method as defined by MIL-STD 705C and IEEE STD 115, METHOD 6.4.4. All generators have class H (180°C) insulation system on both rotor and stator windings. All factory tests and KW/KVA charts shown above are based 120°C (standby) R/R winding temperature, within a maximum 40°C ambient condition. Generators operated at standby power ratings must not exceed the temperature rise limitation for class H insulation system, as specified in NEMA MG1-22.40. Specifications & ratings are subject to change without prior notice. Model STANDBY 120ºC RISE HZ SPJD-2100-60 HERTZ 60 210 “OPEN” GEN-SET There is no enclosure, so gen-set must be placed within a weather protected area, un- inhabited by humans or animals, with proper ventilation. Silencer not supplied, as installation requirements are not known. However, this item is available as optional equipment. “LEVEL 2” HOUSED GEN-SET Full aluminum weather protection and superior sound attenuation for specific low noise applications. Critical grade muffler is standard. All generator sets are USA prototype built and thoroughly tested. Production models are USA factory built and 100% load tested. UL2200, UL1446, UL508, UL142, UL498 NFPA 110, 99, 70, 37 All generator sets meet NFPA-110 Level 1, when equipped with the necessary accessories and installed per NFPA standards. NEC 700, 701, 702, 708 NEMA ICS10, MG1, ICS6, AB1 ANSI C62.41, 27, 59, 32, 480, 40Q, 81U, 360-05 ASCE 7-05 & 7-10 All generator sets meet 180 MPH rating. EPA 40CFR Part 60, 1048, 1054, 1065, 1068
Transcript
Gillette Generators, Inc. •••• 2921 Thorne Dr. •Elkhart, IN • 46514 • Ph: 574-264-9639 • Fax: 574-262-1840 • Web: www.gillettegenerators.com • spc4-190719 1
60 HZ MODEL
SPJD-2100 LIQUID COOLED DIESEL ENGINE GENERATOR SET
RATINGS: All single phase gen-sets are dedicated 4 lead windings, rated at unity (1.0) power factor. All three phase gen-sets are 12 lead windings, rated at .8 power factor. 120° C “STANDBY RATINGS” are strictly for gen-sets that are used for back-up emergency power to a failed normal utility power source. This standby rating allows varying loads, with no overload capability, for the entire duration of utility power outage. All gen-set power ratings are based on temperature rise measured by resistance
method as defined by MIL-STD 705C and IEEE STD 115, METHOD 6.4.4. All generators have class H (180°C) insulation system on both rotor and stator windings. All
factory tests and KW/KVA charts shown above are based 120°C (standby) R/R winding temperature, within a maximum 40°C ambient condition. Generators operated at standby power ratings must not exceed the temperature rise limitation for class H insulation system, as specified in NEMA MG1-22.40. Specifications & ratings are subject
to change without prior notice.
Model
STANDBY 120ºC RISE HZ
SPJD-2100-60 HERTZ 60 210
“OPEN” GEN-SET
There is no enclosure, so gen-set must be placed within a weather protected area, un-inhabited by humans or animals, with proper ventilation. Silencer not supplied, as installation requirements are not known. However, this item is available as optional equipment.
“LEVEL 2” HOUSED GEN-SET
Full aluminum weather protection and superior sound attenuation for specific low noise applications. Critical grade muffler is standard.
All generator sets are USA prototype built and thoroughly tested. Production models are USA factory built and 100% load tested.
UL2200, UL1446, UL508, UL142, UL498
NFPA 110, 99, 70, 37 All generator sets meet NFPA-110 Level 1, when equipped with the necessary accessories and installed per NFPA standards.
Gillette Generators, Inc. •••• 2921 Thorne Dr. •Elkhart, IN • 46514 • Ph: 574-264-9639 • Fax: 574-262-1840 • Web: www.gillettegenerators.com • spc4-190719 2
GENERATOR SPECIFICATIONS
Manufacturer ................................... Stamford Electric Generators Model & Type ...... UCID274J-311, 4 Pole, 12 Lead, Three Phase ........................ UCI274H-17, 4 Pole, 6 Lead, 600V, Three Phase Exciter ..................................................... Brushless, shunt excited Voltage Regulator ....................................... Solid State, HZ/Volts Voltage Regulation ................................ ½%, No load to full load Frequency ............................................................................ 60 HZ
Frequency Regulation ........ ± ½% (1/2 cycle, no load to full load) Unbalanced Load Capability ..................... 100% of standby amps
Total Stator and Load Insulation ........................... Class H, 180°C
Temperature Rise ......... 120°C R/R, standby rating @ 40°C amb. 3 Ø Motor Starting @ 30% Voltage Dip (208-240V) ..... 620 kVA 3 Ø Motor Starting @ 30% Voltage Dip (480V) ............ 840 kVA 3 Ø Motor Starting @ 30% Voltage Dip (600V) ............ 850 kVA Bearing ..................................................... 1, Pre-lubed and sealed Coupling .......................................................... Direct flexible disc Total Harmonic Distortion ............... Max 3½% (MIL-STD705B) Telephone Interference Factor ............ Max 50 (NEMA MG1-22) Deviation Factor ................................. Max 5% (MIL-STD 405B) Ltd. Warranty Period .................. 24 Months from start-up date or ....................................................... 1000 hours use, first to occur.
ENGINE ___________________________________
Manufacturer ............................................................... John Deere Model and Type .................... 6068HF485, 4 cycle, liquid Cooled Aspiration ................................................................ Turbocharged Charged Air Cooled System ……………….………… Air to Air Cylinder Arrangement ................................... 6 Cylinders, In-Line Displacement Cu. In. (Liters) .......................................... 415 (6.8) Bore & Stroke in (Cm.) ............................... 4.19 x 5 (10.6 x 12.7) Compression Ratio .............................................................. 17.0:1 Main Bearings & Style ............................... 7, Replaceable Inserts Cylinder Head ................................................................. Cast Iron Pistons ............................................................ 6, Aluminum Alloy Crankshaft ................................................... Forged Chrome Steel Exhaust Valve ........................................................ Stainless Steel Governor ............................... JDEC Electronic L16 DENSO HP3
Frequency Regulation ........................................................ ± 1/4% Air Cleaner ......................................... Dry, Replaceable Cartridge Engine Speed ................................................................. 1800 rpm Max Power, bhp (kwm) Standby .................. ................ 315 (235) BMEP: psi (kpa) Standby ............................. .............. 334 (2304) Ltd. Warranty Period ........... 24 months or 2000 hrs, first to occur
FUEL SYSTEM ____________________________
Type ......................................... Diesel Fuel Oil (ASTM No. 2-D) Combustion System ............................................. Direct Injection Fuel Injection Pump ................................. Stanadyne Rotary Type 12 VDC air intake heaters ............................. Standard Equipment Fuel Filter and Water Separator………...……………………Yes
GENERATOR FEATURES
• World Renown Stamford Electric Generator having UL-1446 certification.
• Full generator protection with Deep Sea 7420 controller, having UL-508 certification.
• Automatic voltage regulator with over-excitation, under-frequency compensation, under-speed protection, and EMI filtering. Entire solid-state board is encapsulated for moisture protection.
• Generator power ratings are based on temperature rise, measured by resistance method, as defined in MIL-STD 705C and IEEE STD 115, Method 6.4.4.
• Power ratings will not exceed temperature rise limitation for class H insulation as per NEMA MG1-22.40.
• Insulation resistance to ground, exceeds 1.5 meg-ohm.
• Stator receives 2000 V. hi-potential test on main windings, and rotor windings receive a 1500 V. hi-potential test, as per MIL-STD 705B.
• Full amortisseur windings with UL-1446 certification.
• Complete engine-generator torsional acceptance, confirmed during initial prototype testing.
• Full load testing on all engine-generator sets, before shipping. • Self ventilating and drip-proof & revolving field design
FUEL CONSUMPTION
GAL/HR (LITER/HR) STANDBY
100% LOAD 15.5 (58.7)
75% LOAD 11.3 (42.8)
50% LOAD 7.9 (29.9)
OIL SYSTEM
Type ......................................................................... Full Pressure Oil Pan Capacity qt. (L) ............................................... 34.4 (32.5) Oil Pan Cap. W/ filter qt. (L) ....................................... 35.3 (33.4) Oil Filter .................................................. 1, Replaceable Spin-On
Recommended Battery to -18°C (0°F): ... 12 VDC, Size BCI# 27, Max Dimensions: ........ 12" lg X 6 3/4” wi X 9" hi, with standard round posts. Min output at 700 CCA. Battery tray (max. dim. at 12”lg x 7”wi), hold down straps, battery cables, and battery charger, is furnished. Installation of (1) starting battery is required, with possible higher AMP/HR rating, as described
above, if normal environment averages -13°F (-25°C) or cooler.
CERTIFICATIONS
All engines are CARB and EPA emissions certified. All emergency stationary diesel engines are Tier III compliant.
APPLICATION AND ENGINEERING DATA FOR MODEL SPJD-2100-60 HZ
ENGINE SPECIFICATIONS AND APPLICATIONS DATA
Gillette Generators, Inc. •••• 2921 Thorne Dr. •Elkhart, IN • 46514 • Ph: 574-264-9639 • Fax: 574-262-1840 • Web: www.gillettegenerators.com • spc4-190719 3
COOLING SYSTEM
Type of System ............................ Air to Air, Charged Air Cooler Coolant Pump ..................................... Pre-lubricated, self-sealing Cooling Fan Type (no. of blades) ................................. Pusher (7) Fan Diameter inches (cm) ............................................. 22" (55.9)
Note: Coolant temp. shut-down switch setting at 212°F (100°C) with 50/50 (water/antifreeze) mix.
COOLING AIR REQUIREMENTS
Combustion Air cfm (m3/min) ...................... ............... 619 (17.5) Max Air Intake Restrictions: Clean Air Cleaner, H2O (KPA) .............. ................. 15 (3.75) Intake Manifold Pressure, Psi (kpa) .............. ............ …..37 (252) Max. Allowable Temp. Rise, Amb.
Air to Eng. Inlet, °F (°C) ....................... ................ …..15 (8) Max. Temp. out of Charger Air Cooler
@ 77° F (25°C), Amb. Air °F (°C) ........ ................. 140 (60) Radiator Cooling Air, SCFM (m3/min)…………….8000 (226.5)
EXHAUST SYSTEM
Exhaust Outlet Size ................................................................. 3.5" Max. Back Pressure in H2O (kpa) ...................................... 40 (10) Exhaust Flow, at rated KW, cfm (m3/min) ... ............. 1514 (42.9)
Exhaust Temp, at rated KW, °F (ºC)............. ................ 905 (485)
Deep Sea 7420 The “7420” controller is an auto start mains (utility) failure module for single gen-set applications. This controller includes a backlit LCD display which continuously displays the status of the engine and generator at all times.
The “7420” controller will also monitor speed, frequency, voltage, current, oil pressure, coolant temp., and fuel levels. These modules have been designed to display warning and shut
down status. It also includes: (11) configurable inputs • (8)
configurable outputs • voltage monitoring • mains (utility)
Note: Open sets (no enclosure) have silencer system choices due to unknown job-site applications. Level 2 enclosure has installed critical silencer with upgrade to Level 3 hospital silencer. Sound tests are averaged from several test points and taken at 23 ft. (7 m) from source of noise at normal operation.
DERATE GENERATOR FOR ALTITUDE
3% per 1000 ft.(305 meters) above 3000 ft. (914 meters) from sea level.
This controller includes expansion features including RS232, RS484 (using MODBUS-RTU/TCP), direct USB connection with PC, expansion optioned using DSENet for remote annunciation and remote relay interfacing for a distance of up to 3300FT. The controller software is freely downloadable from the internet and allows monitoring with direct USB cable, LAN, or by internet via the built in web interface.
Further expansion is available by adding the optional “WebNet“ gateway interface module. This device will allow comprehensive monitoring of the generator via the cloud including identification, location, and status. Some advantages of this module include: reduced site visits and
maintenance costs • remote fuel management
• fault analysis • asset tracking • automatic
system alerts • maximized system up-time.
APPLICATION AND ENGINEERING DATA FOR MODEL SPJD-2100-60 HZ
DEEP SEA 7420 DIGITAL MICROPROCESSOR CONTROLLER
Gillette Generators, Inc. •••• 2921 Thorne Dr. •Elkhart, IN • 46514 • Ph: 574-264-9639 • Fax: 574-262-1840 • Web: www.gillettegenerators.com • spc4-190719 4
CONTROL PANEL: Deep Sea 7420 digital microprocessor with logic allows programming in the field. Controller has:
• STOP-MANUAL-AUTO modes and automatic engine shutdowns, signaled by full text LCD indicators:
• Low oil pressure Engine fail to start
• High engine temp Engine over speed Low Radiator Level Engine under speed Three auxiliary alarms Over & under voltage Battery fail alarm
Also included is tamper-proof engine hour meter
ENGINE:
Full flow oil filter • Air filter • Oil pump • Solenoid type
starter motor • Hi-temp radiator • Jacket water pump
• Thermostat • Pusher fan and guard • Exhaust manifold
Design & specifications subject to change without prior notice. Dimensions shown are approximate. Contact Gillette for certified drawings. DO NOT USE DIMENSIONS FOR INSTALLATION PURPOSES.
Engine Performance Curves 6068 - Generator June 2007
Ref: Engine Emission Label
Tier-3 Emission Certifications: Certified by:
Notes:
ENGINE PERFORMANCE CURVE
Air Intake Restriction ...................12 in.H2O (3 kPa) Exhaust Back Pressure ........... 30 in.H2O (7.5 kPa)
Gross power guaranteed within + or - 5% at SAE J1995 and ISO 3046 conditions:
Fuel System Prime StandbyECU Description ...................................L14 ControllerFuel System Description................................... HPCRFuel Injection Pump .................................Denso HP3Governor Type ............................................ ElectronicTotal Fuel Flow--lb/hr (kg/hr)..........161 (73.1) .... 174 (78.7)Fuel Consumption--lb/hr (kg/hr)..........97 (44) ....... 110 (50)
25 % Power50 % Power75 % Power100 % Powe
Number of Cylinders ......................................................... 6Bore and Stroke--in. (mm).............. 4.19 x 5.00 (106 x 127)Displacement--in.3 (L) ...........................................415 (6.8)Compression Ratio ................................................... 17.0:1Valves per Cylinder--Intake/Exhaust ............................ 2 / 2Firing Order....................................................... 1-5-3-6-2-4Combustion System....................................... Unit InjectionEngine Type ................................................ In-line, 4-CycleAspiration ......................................................TurbochargedCharge Air Cooling System...................................Air-to-AirEngine Crankcase Vent System ................................ Open
(Includes flywheel hsg., flywheel & electrics)Center of Gravity Location
From Rear Face of Block (X-axis)--in. (mm).15.5 (394)Right of Crankshaft (Y-axis)--in. (mm) ........ -0.1 (-2.24)Above Crankshaft (Z-axis)--in. (mm) ..............7.4 (189)
Cooling SystemEngine Heat Reject.--BCoolant Flow--gal/min Thermostat Start to OpThermostat Fully Open
AP
PR
OV
ED
DO
CU
ME
NT
UCDI274J - Winding 311
Technical Data Sheet
AP
PR
OV
ED
DO
CU
ME
NT
UCDI274JSPECIFICATIONS & OPTIONS
STANDARDS Stamford industrial generators meet the requirements of BS EN 60034 and the relevant section of other internationalstandards such as BS5000, VDE 0530, NEMA MG1-32, IEC34,CSA C22.2-100, AS1359.Other standards and certifications can be considered onrequest.
VOLTAGE REGULATORS
SX460 AVR - STANDARD
With this self excited control system the main stator suppliespower via the Automatic Voltage Regulator (AVR) to the exciterstator. The high efficiency semiconductors of the AVR ensurepositive build-up from initial low levels of residual voltage.The exciter rotor output is fed to the main rotor through a threephase full wave bridge rectifier. This rectifier is protected by asurge suppressor against surges caused, for example, by shortcircuit.
AS440 AVR
With this self-excited system the main stator provides power viathe AVR to the exciter stator. The high efficiency semi-conductors of the AVR ensure positive build-up from initial lowlevels of residual voltage.The exciter rotor output is fed to the main rotor through a three-phase full-wave bridge rectifier. The rectifier is protected by asurge suppressor against surges caused, for example, by shortcircuit or out-of-phase paralleling.The AS440 will support a range of electronic accessories,including a 'droop' Current Transformer (CT) to permit paralleloperation with other ac generators.
MX341 AVR
This sophisticated AVR is incorporated into the StamfordPermanent Magnet Generator (PMG) control system.The PMG provides power via the AVR to the main exciter,giving a source of constant excitation power independent ofgenerator output. The main exciter output is then fed to themain rotor, through a full wave bridge, protected by a surgesuppressor. The AVR has in-built protection against sustainedover-excitation, caused by internal or external faults. This de-excites the machine after a minimum of 5 seconds.An engine relief load acceptance feature can enable full load tobe applied to the generator in a single step.If three-phase sensing is required with the PMG system theMX321 AVR must be used.We recommend three-phase sensing for applications withgreatly unbalanced or highly non-linear loads.
MX321 AVR
The most sophisticated of all our AVRs combines all thefeatures of the MX341 with, additionally, three-phase rmssensing, for improved regulation and performance.Over voltage protection is built-in and short circuit current leveladjustments is an optional facility.
WINDINGS & ELECTRICAL PERFORMANCE
All generator stators are wound to 2/3 pitch. This eliminatestriplen (3rd, 9th, 15th …) harmonics on the voltage waveformand is found to be the optimum design for trouble-free supplyof non-linear loads. The 2/3 pitch design avoids excessiveneutral currents sometimes seen with higher winding pitches,when in parallel with the mains. A fully connected damperwinding reduces oscillations during paralleling. This winding,with the 2/3 pitch and carefully selected pole and toothdesigns, ensures very low waveform distortion.
TERMINALS & TERMINAL BOX
Standard generators are 3-phase reconnectable with 12 endsbrought out to the terminals, which are mounted on a cover atthe non-drive end of the generator. A sheet steel terminal boxcontains the AVR and provides ample space for thecustomers' wiring and gland arrangements. It has removablepanels for easy access.
SHAFT & KEYS
All generator rotors are dynamically balanced to better thanBS6861:Part 1 Grade 2.5 for minimum vibration in operation.
INSULATION/IMPREGNATION
The insulation system is class 'H'.All wound components are impregnated with materials andprocesses designed specifically to provide the high buildrequired for static windings and the high mechanical strengthrequired for rotating components.
QUALITY ASSURANCE
Generators are manufactured using production procedureshaving a quality assurance level to BS EN ISO 9001.
The stated voltage regulation may not be maintained in thepresence of certain radio transmitted signals. Any change inperformance will fall within the limits of Criteria 'B' of EN61000-6-2:2001. At no time will the steady-state voltageregulation exceed 2%.
DE RATES
All values tabulated on page 8 are subject to the followingreductions
5% when air inlet filters are fitted.3% for every 500 metres by which the operating altitudeexceeds 1000 metres above mean sea level.3% for every 5°C by which the operational ambienttemperature exceeds 40°C.
Note: Requirement for operating in an ambient exceeding60°C must be referred to the factory. NB Continuous development of our products entitles us tochange specification details without notice, therefore theymust not be regarded as binding.
Front cover drawing typical of product range.
2
AP
PR
OV
ED
DO
CU
ME
NT
CONTROL SYSTEM SER.3 SEPARATELY EXCITED BY P.M.G.
A.V.R. MX321 MX341
VOLTAGE REGULATION ± 0.5 % ± 1.0 % With 4% ENGINE GOVERNING
SUSTAINED SHORT CIRCUIT
CONTROL SYSTEM SER.4 SELF EXCITED
A.V.R. SX460 AS440
VOLTAGE REGULATION ± 1.0 % ± 1.0 % With 4% ENGINE GOVERNING
SUSTAINED SHORT CIRCUIT SERIES 4 CONTROL DOES NOT SUSTAIN A SHORT CIRCUIT CURRENT
INSULATION SYSTEM CLASS H
PROTECTION
RATED POWER FACTOR
STATOR WINDING
WINDING PITCH
WINDING LEADS
STATOR WDG. RESISTANCE
ROTOR WDG. RESISTANCE
EXCITER STATOR RESISTANCE
EXCITER ROTOR RESISTANCE
R.F.I. SUPPRESSION BS EN 61000-6-2 & BS EN 61000-6-4,VDE 0875G, VDE 0875N. refer to factory for others
WAVEFORM DISTORTION NO LOAD < 1.5% NON-DISTORTING BALANCED LINEAR LOAD < 5.0%
MAXIMUM OVERSPEED
BEARING NON-DRIVE END
WEIGHT COMP. GENERATOR
WEIGHT WOUND STATOR
WEIGHT WOUND ROTOR
WR² INERTIA
SHIPPING WEIGHTS in a crate
PACKING CRATE SIZE
TELEPHONE INTERFERENCE
COOLING AIR
VOLTAGE SERIES STAR 380/220 400/231 415/240 440/254 416/240 440/254 460/266 480/277
VOLTAGE PARALLEL STAR 190/110 200/115 208/120 220/127 208/120 220/127 230/133 240/138
VOLTAGE SERIES DELTA 220/110 230/115 240/120 254/127 240/120 254/127 266/133 277/138kVA BASE RATING FOR REACTANCE VALUES
3-phase 2-phase L-L 1-phase L-NVoltage Factor Voltage Factor x 1.00 x 0.87 x 1.30
380v X 1.00 416v X 1.00 x 1.00 x 1.80 x 3.20400v X 1.05 440v X 1.07 x 1.00 x 1.50 x 2.50415v X 1.10 460v X 1.12 10 sec. 5 sec. 2 sec.
480v X 1.16The sustained current value is constant irrespectiveof voltage level
Three-phase Short Circuit Decrement Curve. No-load Excitation at Rated SpeedBased on star (wye) connection.
Max. sustained durationAll other times are unchanged
Instantaneous
SustainedMinimum
UCDI274J
50Hz 60Hz
Sustained Short Circuit = 850 Amps
Sustained Short Circuit = 1,000 AmpsNote 1The following multiplication factors should beused to adjust the values from curve betweentime 0.001 seconds and the minimum currentpoint in respect of nominal operating voltage :
Note 2The following multiplication factor should be used to convert thevalues calculated in accordance with NOTE 1 to those applicableto the various types of short circuit :
Note 3Curves are drawn for Star (Wye) connected machines. For otherconnection the following multipliers should be applied to currentvalues as shown : Parallel Star = Curve current value X 2Series Delta = Curve current value X 1.732
50Hz
60Hz
100
1000
10000
0.001 0.01 0.1 1 10TIME (secs)
CURR
ENT
(Am
ps)
SYMMETRICAL
ASYMMETRICAL
100
1000
10000
0.001 0.01 0.1 1 10TIME (secs)
CUR
REN
T (A
mps
)
SYMMETRICAL
ASYMMETRICAL
7
AP
PR
OV
ED
DO
CU
ME
NT
Class - Temp Rise
Series Star (V) 380 400 415 440 380 400 415 440 380 400 415 440 380 400 415 440
RATINGSCont. F - 105/40°C Cont. H - 125/40°C Standby - 150/40°C Standby - 163/27°C
DIMENSIONS
50Hz
60Hz
8
AP
PR
OV
ED
DO
CU
ME
NT
UCD274J-311-TD-EN-SG-A
Head Office Address:
Barnack Road, StamfordLincolnshire, PE9 2NB
United KingdomTel: +44 (0) 1780 484000Fax: +44 (0) 1780 484100
www.cumminsgeneratortechnologies.com
Copyright 2010, Cummins Generator Technologies Ltd, All Rights ReservedStamford and AvK are registered trade marks of Cummins Generator Technologies Ltd
Cummins and the Cummins logo are registered trade marks of Cummins Inc.
AP
PR
OV
ED
DO
CU
ME
NT
UCI274H - Winding 17
Technical Data Sheet
AP
PR
OV
ED
DO
CU
ME
NT
UCI274HSPECIFICATIONS & OPTIONS
STANDARDS
Stamford industrial generators meet the requirements ofBS EN 60034 and the relevant section of other internationalstandards such as BS5000, VDE 0530, NEMA MG1-32, IEC34,CSA C22.2-100, AS1359.Other standards and certifications can be considered onrequest.
VOLTAGE REGULATORS
SX460 AVR - STANDARD
With this self excited control system the main stator suppliespower via the Automatic Voltage Regulator (AVR) to the exciterstator. The high efficiency semiconductors of the AVR ensurepositive build-up from initial low levels of residual voltage.The exciter rotor output is fed to the main rotor through a threephase full wave bridge rectifier. This rectifier is protected by asurge suppressor against surges caused, for example, by shortcircuit.
AS440 AVR
With this self-excited system the main stator provides power viathe AVR to the exciter stator. The high efficiency semi-conductors of the AVR ensure positive build-up from initial lowlevels of residual voltage.The exciter rotor output is fed to the main rotor through a three-phase full-wave bridge rectifier. The rectifier is protected by asurge suppressor against surges caused, for example, by shortcircuit or out-of-phase paralleling.The AS440 will support a range of electronic accessories,including a 'droop' Current Transformer (CT) to permit parallel
WINDINGS & ELECTRICAL PERFORMANCE
All generator stators are wound to 2/3 pitch. This eliminatestriplen (3rd, 9th, 15th …) harmonics on the voltage waveformand is found to be the optimum design for trouble-free supplyof non-linear loads. The 2/3 pitch design avoids excessiveneutral currents sometimes seen with higher winding pitches,when in parallel with the mains. A fully connected damperwinding reduces oscillations during paralleling. This winding,with the 2/3 pitch and carefully selected pole and toothdesigns, ensures very low waveform distortion.
TERMINALS & TERMINAL BOX
Standard generators are 3-phase reconnectable with 12 endsbrought out to the terminals, which are mounted on a cover atthe non-drive end of the generator. A sheet steel terminal boxcontains the AVR and provides ample space for thecustomers' wiring and gland arrangements. It has removablepanels for easy access.
SHAFT & KEYS
All generator rotors are dynamically balanced to better thanBS6861:Part 1 Grade 2.5 for minimum vibration in operation.
INSULATION/IMPREGNATION
The insulation system is class 'H'.All wound components are impregnated with materials andprocesses designed specifically to provide the high buildrequired for static windings and the high mechanical strengthrequired for rotating components.
STANDARDS
Stamford industrial generators meet the requirements ofBS EN 60034 and the relevant section of other internationalstandards such as BS5000, VDE 0530, NEMA MG1-32, IEC34,CSA C22.2-100, AS1359.Other standards and certifications can be considered onrequest.
VOLTAGE REGULATORS
SX460 AVR - STANDARD
With this self excited control system the main stator suppliespower via the Automatic Voltage Regulator (AVR) to the exciterstator. The high efficiency semiconductors of the AVR ensurepositive build-up from initial low levels of residual voltage.The exciter rotor output is fed to the main rotor through a threephase full wave bridge rectifier. This rectifier is protected by asurge suppressor against surges caused, for example, by shortcircuit.
AS440 AVR
With this self-excited system the main stator provides power viathe AVR to the exciter stator. The high efficiency semi-conductors of the AVR ensure positive build-up from initial lowlevels of residual voltage.The exciter rotor output is fed to the main rotor through a three-phase full-wave bridge rectifier. The rectifier is protected by asurge suppressor against surges caused, for example, by shortcircuit or out-of-phase paralleling.The AS440 will support a range of electronic accessories,including a 'droop' Current Transformer (CT) to permit paralleloperation with other ac generators.
MX341 AVR
This sophisticated AVR is incorporated into the StamfordPermanent Magnet Generator (PMG) control system.The PMG provides power via the AVR to the main exciter,giving a source of constant excitation power independent ofgenerator output. The main exciter output is then fed to themain rotor, through a full wave bridge, protected by a surgesuppressor. The AVR has in-built protection against sustainedover-excitation, caused by internal or external faults. This de-excites the machine after a minimum of 5 seconds.An engine relief load acceptance feature can enable full load tobe applied to the generator in a single step.If three-phase sensing is required with the PMG system theMX321 AVR must be used.We recommend three-phase sensing for applications withgreatly unbalanced or highly non-linear loads.
MX321 AVR
The most sophisticated of all our AVRs combines all thefeatures of the MX341 with, additionally, three-phase rmssensing, for improved regulation and performance.Over voltage protection is built-in and short circuit current leveladjustments is an optional facility.
WINDINGS & ELECTRICAL PERFORMANCE
All generator stators are wound to 2/3 pitch. This eliminatestriplen (3rd, 9th, 15th …) harmonics on the voltage waveformand is found to be the optimum design for trouble-free supplyof non-linear loads. The 2/3 pitch design avoids excessiveneutral currents sometimes seen with higher winding pitches,when in parallel with the mains. A fully connected damperwinding reduces oscillations during paralleling. This winding,with the 2/3 pitch and carefully selected pole and toothdesigns, ensures very low waveform distortion.
TERMINALS & TERMINAL BOX
Standard generators are 3-phase reconnectable with 12 endsbrought out to the terminals, which are mounted on a cover atthe non-drive end of the generator. A sheet steel terminal boxcontains the AVR and provides ample space for thecustomers' wiring and gland arrangements. It has removablepanels for easy access.
SHAFT & KEYS
All generator rotors are dynamically balanced to better thanBS6861:Part 1 Grade 2.5 for minimum vibration in operation.
INSULATION/IMPREGNATION
The insulation system is class 'H'.All wound components are impregnated with materials andprocesses designed specifically to provide the high buildrequired for static windings and the high mechanical strengthrequired for rotating components.
QUALITY ASSURANCE
Generators are manufactured using production procedureshaving a quality assurance level to BS EN ISO 9001.
The stated voltage regulation may not be maintained in thepresence of certain radio transmitted signals. Any change inperformance will fall within the limits of Criteria 'B' of EN61000-6-2:2001. At no time will the steady-state voltageregulation exceed 2%.
DE RATES
All values tabulated on page 6 are subject to the followingreductions
5% when air inlet filters are fitted.3% for every 500 metres by which the operating altitudeexceeds 1000 metres above mean sea level.3% for every 5 C by which the operational ambienttemperature exceeds 40 C.
Note: Requirement for operating in an ambient exceeding60 C must be referred to the factory.
NB Continuous development of our products entitles us tochange specification details without notice, therefore theymust not be regarded as binding.
Front cover drawing typical of product range.
STANDARDS
Stamford industrial generators meet the requirements ofBS EN 60034 and the relevant section of other internationalstandards such as BS5000, VDE 0530, NEMA MG1-32, IEC34,CSA C22.2-100, AS1359.Other standards and certifications can be considered onrequest.
VOLTAGE REGULATORS
SX460 AVR - STANDARD
With this self excited control system the main stator suppliespower via the Automatic Voltage Regulator (AVR) to the exciterstator. The high efficiency semiconductors of the AVR ensurepositive build-up from initial low levels of residual voltage.The exciter rotor output is fed to the main rotor through a threephase full wave bridge rectifier. This rectifier is protected by asurge suppressor against surges caused, for example, by shortcircuit.
AS440 AVR
With this self-excited system the main stator provides power viathe AVR to the exciter stator. The high efficiency semi-conductors of the AVR ensure positive build-up from initial lowlevels of residual voltage.The exciter rotor output is fed to the main rotor through a three-phase full-wave bridge rectifier. The rectifier is protected by asurge suppressor against surges caused, for example, by shortcircuit or out-of-phase paralleling.The AS440 will support a range of electronic accessories,including a 'droop' Current Transformer (CT) to permit paralleloperation with other ac generators.
MX341 AVR
This sophisticated AVR is incorporated into the StamfordPermanent Magnet Generator (PMG) control system.The PMG provides power via the AVR to the main exciter,giving a source of constant excitation power independent ofgenerator output. The main exciter output is then fed to themain rotor, through a full wave bridge, protected by a surgesuppressor. The AVR has in-built protection against sustainedover-excitation, caused by internal or external faults. This de-excites the machine after a minimum of 5 seconds.An engine relief load acceptance feature can enable full load tobe applied to the generator in a single step.If three-phase sensing is required with the PMG system theMX321 AVR must be used.We recommend three-phase sensing for applications withgreatly unbalanced or highly non-linear loads.
MX321 AVR
The most sophisticated of all our AVRs combines all thefeatures of the MX341 with, additionally, three-phase rmssensing, for improved regulation and performance.Over voltage protection is built-in and short circuit current leveladjustments is an optional facility.
WINDINGS & ELECTRICAL PERFORMANCE
All generator stators are wound to 2/3 pitch. This eliminatestriplen (3rd, 9th, 15th …) harmonics on the voltage waveformand is found to be the optimum design for trouble-free supplyof non-linear loads. The 2/3 pitch design avoids excessiveneutral currents sometimes seen with higher winding pitches,when in parallel with the mains. A fully connected damperwinding reduces oscillations during paralleling. This winding,with the 2/3 pitch and carefully selected pole and toothdesigns, ensures very low waveform distortion.
TERMINALS & TERMINAL BOX
Standard generators are 3-phase reconnectable with 12 endsbrought out to the terminals, which are mounted on a cover atthe non-drive end of the generator. A sheet steel terminal boxcontains the AVR and provides ample space for thecustomers' wiring and gland arrangements. It has removablepanels for easy access.
SHAFT & KEYS
All generator rotors are dynamically balanced to better thanBS6861:Part 1 Grade 2.5 for minimum vibration in operation.
INSULATION/IMPREGNATION
The insulation system is class 'H'.All wound components are impregnated with materials andprocesses designed specifically to provide the high buildrequired for static windings and the high mechanical strengthrequired for rotating components.
QUALITY ASSURANCE
Generators are manufactured using production procedureshaving a quality assurance level to BS EN ISO 9001.
The stated voltage regulation may not be maintained in thepresence of certain radio transmitted signals. Any change inperformance will fall within the limits of Criteria 'B' of EN61000-6-2:2001. At no time will the steady-state voltageregulation exceed 2%.
DE RATES
All values tabulated on page 6 are subject to the followingreductions
5% when air inlet filters are fitted.3% for every 500 metres by which the operating altitudeexceeds 1000 metres above mean sea level.3% for every 5 C by which the operational ambienttemperature exceeds 40 C.
Note: Requirement for operating in an ambient exceeding60 C must be referred to the factory.
NB Continuous development of our products entitles us tochange specification details without notice, therefore theymust not be regarded as binding.
Front cover drawing typical of product range.
2
AP
PR
OV
ED
DO
CU
ME
NT
CONTROL SYSTEM SEPARATELY EXCITED BY P.M.G.
A.V.R. MX321 MX341
VOLTAGE REGULATION ± 0.5 % ± 1.0 % With 4% ENGINE GOVERNING
SUSTAINED SHORT CIRCUIT
CONTROL SYSTEM SELF EXCITED
A.V.R. SX460 AS440
VOLTAGE REGULATION ± 1.5 % ± 1.0 % With 4% ENGINE GOVERNING
SUSTAINED SHORT CIRCUIT SERIES 4 CONTROL DOES NOT SUSTAIN A SHORT CIRCUIT CURRENT
INSULATION SYSTEM CLASS H
PROTECTION
RATED POWER FACTOR
STATOR WINDING
WINDING PITCH
WINDING LEADS
STATOR WDG. RESISTANCE
ROTOR WDG. RESISTANCE
EXCITER STATOR RESISTANCE
EXCITER ROTOR RESISTANCE
R.F.I. SUPPRESSION BS EN 61000-6-2 & BS EN 61000-6-4,VDE 0875G, VDE 0875N. refer to factory for others
WAVEFORM DISTORTION NO LOAD < 1.5% NON-DISTORTING BALANCED LINEAR LOAD < 5.0%
MAXIMUM OVERSPEED
BEARING DRIVE END
BEARING NON-DRIVE END
UCI274HWINDING 17
REFER TO SHORT CIRCUIT DECREMENT CURVES (page 5)
BALL. 6310-2RS (ISO)
IP23
0.8
1.82 Ohms at 22°C
0.028 Ohms PER PHASE AT 22°C SERIES STAR CONNECTED
TWO THIRDS
12
20 Ohms at 22°C
0.091 Ohms PER PHASE AT 22°C
DOUBLE LAYER CONCENTRIC
2250 Rev/Min
BALL. 6315-2RS (ISO)
WEIGHT COMP. GENERATOR
WEIGHT WOUND STATOR
WEIGHT WOUND ROTOR
WR² INERTIA
SHIPPING WEIGHTS in a crate
PACKING CRATE SIZE
TELEPHONE INTERFERENCE
COOLING AIR
VOLTAGE SERIES STAR
VOLTAGE PARALLEL STAR
VOLTAGE SERIES DELTA
kVA BASE RATING FOR REACTANCE VALUES
Xd DIR. AXIS SYNCHRONOUS
X'd DIR. AXIS TRANSIENT
X''d DIR. AXIS SUBTRANSIENT
Xq QUAD. AXIS REACTANCE
X''q QUAD. AXIS SUBTRANSIENT
XL LEAKAGE REACTANCE
X2 NEGATIVE SEQUENCE
X0 ZERO SEQUENCE
REACTANCES ARE SATURATED VALUES ARE PER UNIT AT RATING AND VOLTAGE INDICATED
Three-phase Short Circuit Decrement Curve. No-load Excitation at Rated Speed
THREE PHASE EFFICIENCY CURVES
Based on star (wye) connection.
1000
10000
SYMMETRICAL
ASYMMETRICAL
3-phase 2-phase L-L 1-phase L-N
x 1.00 x 0.87 x 1.30
x 1.00 x 1.80 x 3.20
x 1.00 x 1.50 x 2.50
10 sec. 5 sec. 2 sec.
SustainedMax. sustained duration
All other times are unchanged
InstantaneousMinimum
Sustained Short Circuit = 860 Amps
NoteThe following multiplication factor should be used to convert the values from curve for thevarious types of short circuit :
10
100
1000
10000
0.001 0.01 0.1 1 10TIME (secs)
CU
RR
ENT
(Am
ps)
SYMMETRICAL
ASYMMETRICAL
55
AP
PR
OV
ED
DO
CU
ME
NT
Class - Temp Rise
Series Star (V)
Parallel Star (V)
Series Delta (V)
kVA
kW
Efficiency (%)
kW Input 235.6
346
280.0
224.0
93.3
240.0
346
275.0
220.0
93.4
188.0
93.7
200.6
346
255.0
204.0
93.6
218.0
DIMENSIONS
UCI274H
Cont. F - 105/40°C Cont. H - 125/40°C Standby - 150/40°C Standby - 163/27°C
Winding 17 / 0.8 Power Factor
RATINGS
346
235.0
600
300
600
300
600
300
600
300
60Hz60Hz
66
AP
PR
OV
ED
DO
CU
ME
NT
UCI274H-17-TD-EN-SG-A
Head Office Address:Barnack Road, StamfordLincolnshire, PE9 2NB
United KingdomTel: +44 (0) 1780 484000Fax: +44 (0) 1780 484100
www.cumminsgeneratortechnologies.com
Copyright 2010, Cummins Generator Technologies Ltd, All Rights ReservedStamford and AvK are registered trade marks of Cummins Generator Technologies Ltd
Cummins and the Cummins logo are registered trade marks of Cummins Inc.
UCI274H-17-TD-EN-SG-A
Head Office Address:Barnack Road, StamfordLincolnshire, PE9 2NB
United KingdomTel: +44 (0) 1780 484000Fax: +44 (0) 1780 484100
www.cumminsgeneratortechnologies.com
Copyright 2010, Cummins Generator Technologies Ltd, All Rights ReservedStamford and AvK are registered trade marks of Cummins Generator Technologies Ltd
Cummins and the Cummins logo are registered trade marks of Cummins Inc.
DSE7410/20AUTO START & AUTO MAINS FAILURE MODULES
DSEGenset
®
11ph2ph3phN
1ph2ph3phEN
1ph2ph3phN
1
11
232
6 4
MODEM
ISSUE 1
RS232 ANDRS485
CONFIGURABLEINPUTS
DC OUTPUTS ANALOGUESENDERS
EMERGENCY STOP
DC POWER SUPPLY 8-35V
DEUTZISUZUPERKINSCATERPILLARMTUVOLVOCUMMINSSCANIA
+D +W/L
GENERATOR SENSING
VOLTSVOLTS CURRENT
ELECTRONICENGINES &MAGNETIC PICK-UP
FUEL & CRANKOUTPUTSFLEXIBLE WITH CAN
CHARGEALTERNATOR
N/O VOLTFREE OUTPUT
N/C VOLT FREEOUTPUT
+
COMPREHENSIVE FEATURE LIST TO SUIT A WIDE VARIETY OFGEN-SET APPLICATIONS
7
OTHER
DSE7410/20
The DSE7410 is an Auto StartControl Module and the DSE7420is an Auto Mains (Utility) FailureControl Module suitable for a widevariety of single, diesel or gas, gen-set applications.
A sophisticated module monitoringan extensive number of engineparameters, the DSE74xx willannunciate warnings, shutdownand engine status information onthe back-lit LCD screen, illuminatedLED, remote PC, audible alarm andvia SMS text alerts. The moduleincludes RS232, RS485 & Ethernetports as well as dedicatedterminals for system expansion.
The DSE7400 Series modules arecompatible with electronic (CAN)and non-electronic (magnetic pick-up/alternator sensing) engines andoffer a comprehensive number offlexible inputs, outputs andextensive engine protections so thesystem can be easily adapted tomeet the most demanding industryparalleling requirements.
The modules can be easilyconfigured using the DSEConfiguration Suite Software.Selected front panel editing is alsoavailable.
FEATURES
ENVIRONMENTAL TESTING STANDARDS
ELECTRO-MAGNETIC COMPATIBILITYBS EN 61000-6-2EMC Generic Immunity Standard for the Industrial EnvironmentBS EN 61000-6-4EMC Generic Emission Standard for the Industrial Environment
ELECTRICAL SAFETYBS EN 60950Safety of Information Technology Equipment, including Electrical Business Equipment
TEMPERATUREBS EN 60068-2-1Ab/Ae Cold Test -30 oCBS EN 60068-2-2Bb/Be Dry Heat +70 oC
VIBRATIONBS EN 60068-2-6Ten sweeps in each of three major axes5 Hz to 8 Hz @ +/-7.5 mm, 8 Hz to 500 Hz @ 2 gn
• Additional display screens tohelp with modem diagnostics
• DSENet® expansion • Integral PLC editor
KEY BENEFITS• RS232, RS485 & Ethernet can
be used at the same time• DSENet® connection for
system expansion• PLC functionality• Five step dummy load support• Five step load shedding support• High number of inputs and
outputs• Worldwide language support• Direct USB connection to PC• Ethernet monitoring• USB host• Data logging & trending
RELATED MATERIALSTITLE PART NO’SDSE7410 Installation Instructions 053-085DSE7420 Installation Instructions 053-088DSE74xx Quick Start Guide 057-162DSE74xx Operator Manual 057-161DSE74xx PC Configuration Suite Manual 057-160
SPECIFICATION
DC SUPPLYCONTINUOUS VOLTAGE RATING8 V to 35 V Continuous
CRANKING DROPOUTSAble to survive 0 V for 50 mS, providing supply was at least 10 V before dropoutand supply recovers to 5 V. This is achieved without the need for internal batteries
MAXIMUM OPERATING CURRENT260 mA at 12 V, 130 mA at 24 V
MAXIMUM STANDBY CURRENT120 mA at 12 V, 65 mA at 24 V
CHARGE FAIL/EXCITATION RANGE0 V to 35 V
OUTPUTSOUTPUT A (FUEL)15 A DC at supply voltage
OUTPUT B (START)15 A DC at supply voltage
OUTPUTS C & D8 A AC at 250 V AC (Volt free)
AUXILIARY OUTPUTS E,F,G,H,I & J2 A DC at supply voltage
GENERATOR VOLTAGE RANGE 15 V to 333 V AC (L-N)
FREQUENCY RANGE3.5 Hz to 75 Hz
MAINS (UTILITY) (DSE7420)VOLTAGE RANGE 15 V to 333 V AC (L-N)
FREQUENCY RANGE3.5 Hz to 75 Hz
BUS (DSE7410)VOLTAGE RANGE 15 V to 333 V AC (L-N)
FREQUENCY RANGE3.5 Hz to 75 Hz
MAGNETIC PICK UPVOLTAGE RANGE+/- 0.5 V to 70 V
FREQUENCY RANGE10,000 Hz (max)
DIMENSIONSOVERALL240 mm x 172 mm x 57 mm 9.4” x 6.8” x 2.2”
PANEL CUTOUT 220 mm x 160 mm 8.7” x 6.3”
MAXIMUM PANEL THICKNESS8 mm0.3”
STORAGE TEMPERATURE RANGE-40 oC to +85 oC
DSE7410/20AUTO START & AUTO MAINS FAILURE MODULES
®
DSEGenset
FEATURES
Registered in England & Wales No.01319649VAT No.316923457
Deep Sea Electronics Plc maintains a policy of continuous development and reserves the right to changethe details shown on this data sheet without prior notice. The contents are intended for guidance only.
The ABB Quality System complies with the international ISO 9001 - 2000 Standard (model for quality assurance in design, development, construction, and installation and service) and with the equivalent European EN ISO 9001 and Italian UNI EN ISO 9001 Standards
Interrupting ratings (RMS sym. kAmps) T5Continuous Current Rating 400-600A
Number of Poles 3-4
N S H L V
AC
240V 65 100 150 200 200
480V 25 35 65 100 150
600V 18 25 35 65 100
DC* ( 400 A only )
500V 2 poles in series 25 35 50 65 100
600V 3 poles in series 16 25 35 50 65
*Thermo Magnetic Trip Only
Auxiliary Devices for Indication and Control
• Auxiliary contacts - AUX
• Undervoltage release - UVR
• Shunt trip - SOR
• Terminal covers
• Front for lever operating mechanism - FLD
• Direct rotary handle - RHD
• Stored energy motor operator - MOE
• Key lock - KLF
• Early auxiliary contact - AUE
ABB Inc. 1206 Hatton RoadWichita Falls, TX 76302For more information and the location of your local fi eld offi ce please go to www.abb-control.com
Pub
licat
ion
LV03
9 N
o. 1
SX
U 2
10 0
39 D
0201
Prin
ted
in U
SA
, Nov
emb
er, 2
005
• Transmitted rotary handle - RHE
• Front terminal for copper cable - FC Cu
• Front extended terminal - EF
• Front terminal for copper-aluminum - FC CuAl
• Front extended spread terminal – ES
• Distribution lugs
• Rear orientated terminal - R
• Phase separators
• Residual current release (IEC Only)
Mounting
Fixed Plug-in Drawout
Connections
Busbar connection or compression lugs Pressure-type terminals for bare cables Rear connections
Trip Unit
TMA thermo magnetic trip units, with adjustable thermal threshold (I1 = 0.7…1 x In) and adjustable magnetic threshold (I3 = 5…10 x In).
PR221DS, PR222DS/P and PR222DS/PD-A electronic trip unit
The new Tmax series has a hologram on the front, obtained using special anti-imitation techniques, which guarantees the quality and that the circuit breaker is an original ABB product.
Attention to protection of the environment and to health and safety in the work place is another priority commitment for ABB and, as confi rmation of this, the company environmental man-agement system has been certifi ed by RINA in 1997, in confor-mity with the international ISO 14001 Standard. This certifi ca-tion has been integrated in 1999 with the Management System for Health and Safety in the workplace, according to OHSAS 18001 (British Standards), obtaining one of the fi rst certifi cation of integrated management System, QES (Quality, Environment,
Safety) issued by RINA. ABB - the fi rst industry in the electro-mechanical section in Italy to obtain this recognition - thanks to a revision of the production process with an eye to ecology has been able to reduce the consumption of raw materials and waste from processing by 20%. ABB’s commitment to safeguarding the environment is also shown in a concrete way by the Life Cycle Assessments of its products carried out directly by the ABB Research and Development in collabora-tion with the ABB Research Center. Selection of materials, processes and packing materials is made optimizing the true environmental impact of the product, also foreseeing the pos-sibility of its being recycled.
Dimensions 3P Fixed Version 10.55H x 8.26W x 4.07D
Weight 20.9 (Ibs)
The ABB Quality System complies with the international ISO 9001 - 2000 Standard (model for quality assurance in design, development, construction, and installation and service) and with the equivalent European EN ISO 9001 and Italian UNI EN ISO 9001 Standards
Interrupting ratings (RMS sym. kAmps) T6Continuous Current Rating 800Number of Poles 3-4
N S H LAC 240V 65 100 200 200 480V 35 50 65 100 600V 20 25 35 42DC* 500V 2 poles in series 35 35 50 65 600V 3 poles in series 20 20 35 50*Thermal Magnetic Trip Only
Auxiliary Devices for Indication and Control
• Auxiliary contacts - AUX
• Undervoltage release - UVR
• Shunt trip - SOR
• Terminal covers
• Front for lever operating mechanism - FLD
• Direct rotary handle - RHD
• Stored energy motor operator - MOE
• Key lock - KLF
• Early auxiliary contact - AUE
ABB Inc. 1206 Hatton RoadWichita Falls, TX 76302For more information and the location of your local field office please go to www.abb-control.com
Pub
licat
ion
LV11
3N
o. 1
SX
U21
0113
D02
01P
rinte
d in
US
A, A
pril
, 200
8
• Transmitted rotary handle - RHE
• Front extended terminal - EF
• Front terminal for copper-aluminum - FC CuAl
• Front extended spread terminal – ES
• Rear orientated terminal - R
• Phase separators
• Residual current relay (IEC Only)
Mounting
Fixed Drawout
Connections
Busbar connection or compression lugs Pressure-type terminals for bare cables Rear connections
Trip Unit
TMA thermal magnetic trip units, with adjustable thermal threshold (I1 = 0.7…1 x In) and adjustable magnetic thresh-old (I3 = 5…10 x In).
PR221DS, PR222DS/P, and PR222DS/PD-A electronic trip unit
The new Tmax series has a hologram on the front, obtained using special anti-imitation techniques, which guarantees the quality and that the circuit breaker is an original ABB product.
Attention to protection of the environment and to health and safety in the work place is another priority commitment for ABB and, as confirmation of this, the company environmental man-agement system has been certified by RINA in 1997, in confor-mity with the international ISO 14001 Standard. This certifica-tion has been integrated in 1999 with the Management System for Health and Safety in the workplace, according to OHSAS 18001 (British Standards), obtaining one of the first certification of integrated management System, QES (Quality, Environment,
Safety) issued by RINA. ABB - the first industry in the electro-mechanical section in Italy to obtain this recognition - thanks to a revision of the production process with an eye to ecology has been able to reduce the consumption of raw materials and waste from processing by 20%. ABB’s commitment to safeguarding the environment is also shown in a concrete way by the Life Cycle Assessments of its products carried out directly by the ABB Research and Development in collabora-tion with the ABB Research Center. Selection of materials, processes and packing materials is made optimizing the true environmental impact of the product, also foreseeing the pos-sibility of its being recycled.
