61168147 manual-de-servicio-sharp-al-2030-2040cs-2050cs

SERVICE MANUAL

Parts marked with “ ” are important for maintaining the safety of the set. Be sure to replace these parts withspecified ones for maintaining the safety and performance of the set.

CONTENTS

CODE: 00ZAL2040CS2E

DIGITAL MULTIFUNCTIONAL SYSTEM

AL-2030AL-2040CS

MODEL AL-2050CSAL-2050CS

[1] GENERAL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 - 1

[2] SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 - 1

[3] CONSUMABLE PARTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 - 1

[4] EXTERNAL VIEWS AND INTERNAL STRUCTURES . . . . . . . . . 4 - 1

[5] UNPACKING AND INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . 5 - 1

[6] COPY PROCESS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 - 1

[7] OPERATIONAL DESCRIPTIONS . . . . . . . . . . . . . . . . . . . . . . . . . 7 - 1

[8] DISASSEMBLY AND ASSEMBLY . . . . . . . . . . . . . . . . . . . . . . . . . 8 - 1

[9] ADJUSTMENTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 - 1

[10] SIMULATION, TROUBLE CODES . . . . . . . . . . . . . . . . . . . . . . . 10 - 1

[11] USER PROGRAM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 - 1

[12] ELECTRICAL SECTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 - 1

[13] CIRCUIT DIAGRAM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 - 1

This document has been published to be usedfor after sales service only.The contents are subject to change without notice.

SHARP CORPORATION

CAUTION

This laser radiation is not a danger to the skin, but when an exact focusing of the laser beam is achievedon the eye’s retina, there is the danger of spot damage to the retina.

The following cautions must be observed to avoid exposure of the laser beam to your eyes at the time ofservicing.

1) When a problem in the laser optical unit has occurred, the whole optical unit must be exchanged as aunit, not as individual parts.

2) Do not look into the machine with the main switch turned on after removing the developer unit, tonercartridge, and drum cartridge.

3) Do not look into the laser beam exposure slit of the laser optical unit with the connector connectedwhen removing and installing the optical system.

4) The middle frame contains the safety interlock switch.

Do not defeat the safety interlock by inserting wedges or other items into the switch slot.

LASER WAVE – LENGTH : 770 ~ 795nmPulse times : 12.88µs ± 12.88ns/7mmOut put power : MAX 0.2mW

CAUTIONINVISIBLE LASER RADIATION,

WHEN OPEN AND INTERLOCKS DEFEATED.

AVOID EXPOSURE TO BEAM.

VORSICHTUNSICHTBARE LASERSTRAHLUNG,WENN ABDECKUNG GEÖFFNET UNDSICHERHEITSVERRIEGELUNG ÜBERBRÜCKT.NICHT DEM STRAHL AUSSETZEN.

VARO !AVATTAESSA JA SUOJALUKITUSOHITETTAESSA OLET ALTTIINANÄKYMÄTTÖMÄLLE LASERSÄTEILYLLE ÄLÄKATSO SÄTEESEEN.

ADVARSELUSYNLIG LASERSTRÅLNING VED ÅBNING, NÅRSIKKERHEDSBRYDERE ER UDE AFFUNKTION. UNDGÅ UDSAETTELSE FORSTRÅLNING.

VARNING !OSYNLIG LASERSTRÅLNING NÄR DENNA DELÄR ÖPPNAD OCH SPÄRREN ÄR URKOPPLAD.BETRAKTA EJ STRÅLEN. – STRÅLEN ÄRFARLIG.

This product is a class 1 laser product that complies with 21CFR 1040 of the CDRH standard andIEC825. This means that this machine does not produce hazardous laser radiation. The use of controls,adjustments or performance of procedures other than those specified herein may result in hazardousradiation exposure.

At the production line, the output powerof the scanner unit is adjusted to 0.18MILLI-WATT PLUS 20 PCTS and ismaintained constant by the operation ofthe Automatic Power Control (APC).Even if the APC circuit fails in operationfor some reason, the maximum outputpower will only be 15 MILLI-WATT 0.1MICRO-SEC. Giving and accessibleemission level of 42 MICRO-WATTwhich is still-less than the limit ofCLASS-1 laser product.

VAROITUS! LAITTEEN KÄYTTÄMINEN MUULLAKUIN TÄSSÄ KÄYTTÖOHJEESSA MAINITULLATAVALLA SAATTAA ALTISTAA KÄYTTÄJÄNTURVALLISUUSLUOKAN 1 YLITTÄVÄLLENÄKYMÄTTÖMÄLLE LASERSÄTEILYLLE.

VARNING - OM APPARATEN ANVÄNDS PÅ ANNATSÄTT ÄN I DENNA BRUKSANVISNINGSPECIFICERATS, KAN ANVÄNDAREN UTSÄTTASFÖR OSYNLIG LASERSTRÅLNING, SOMÖVERSKRIDER GRÄNSEN FÖR LASERKLASS 1.

CautionThis product contains a low power laserdevice. To ensure continued safety do notremove any cover or attempt to gain accessto the inside of the product. Refer allservicing to qualified personnel.

LUOKAN 1 LASERLAITEKLASS 1 LASER APPARAT

The foregoing is applicable only to the 220Vmodel, 230V model and 240V model.

CONTENTS

[1] GENERAL1. Major functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1

[2] SPECIFICATIONS1. Basic Specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-12. Operation specifications . . . . . . . . . . . . . . . . . . . . . . . . 2-13. Copy performance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-24. GDI Printer (AL-2030/2040CS) . . . . . . . . . . . . . . . . . . . 2-35. SPLC printer (AL-2050CS only). . . . . . . . . . . . . . . . . . . 2-36. Scan function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-37. SPF (AL-2030/2040CS). . . . . . . . . . . . . . . . . . . . . . . . . 2-48. RSPF (AL-2050CS) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-4

[3] CONSUMABLE PARTS1. Supply system table. . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-1

A. SEC/SECL (AL-2030/2040CS/2050CS). . . . . . . . . . 3-1B. Brazil (AL-2030/2040CS) . . . . . . . . . . . . . . . . . . . . . 3-1

2. Environmental . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3-13. Production control number (lot No.) identification . . . . . 3-2

[4] EXTERNAL VIEWS AND INTERNAL STRUCTURES1. Appearance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-12. Internal. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-13. Operation panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-2

A. AL-2030/2040CS . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-2B. AL-2050CS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-3

4. Motors and solenoids. . . . . . . . . . . . . . . . . . . . . . . . . . . 4-5A. AL-2030/2040CS . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-5B. AL-2050CS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-6

5. Sensors and switches . . . . . . . . . . . . . . . . . . . . . . . . . . 4-7A. AL-2030/2040CS (For the AL-2030,

the 2nd cassette is not provided.) . . . . . . . . . . . . . . 4-7B. AL-2050CS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-8

6. PWB unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-9A. AL-2030/2040CS . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-9B. AL-2050CS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-10

7. Cross sectional view . . . . . . . . . . . . . . . . . . . . . . . . . . 4-11A. AL-2030/2040CS . . . . . . . . . . . . . . . . . . . . . . . . . . 4-11B. AL-2050CS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-12

[5] UNPACKING AND INSTALLATION1. Copier installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-12. Cautions on handling . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-13. Checking packed components and accessories . . . . . . 5-14. Unpacking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-25. Removing protective packing materials . . . . . . . . . . . . . 5-26. Installing the TD cartridge . . . . . . . . . . . . . . . . . . . . . . . 5-27. Loading paper . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-38. Power to copier . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-39. Software. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-3

A. Before installation. . . . . . . . . . . . . . . . . . . . . . . . . . . 5-3B. Installing the software. . . . . . . . . . . . . . . . . . . . . . . . 5-4C. Setting up Button Manager

(AL-2040CS/2050CS only). . . . . . . . . . . . . . . . . . . . 5-910. Interface. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-10

A. USB . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-10B. RJ45 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-10

11. Moving . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-1012. Scanner moisture-proof kit. . . . . . . . . . . . . . . . . . . . . . 5-10

A. Components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5-10B. Precautions at installation . . . . . . . . . . . . . . . . . . . 5-10C. Attachment method . . . . . . . . . . . . . . . . . . . . . . . . 5-11

[6] COPY PROCESS1. Functional diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-12. Outline of print process . . . . . . . . . . . . . . . . . . . . . . . . . 6-23. Actual print process . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-2

[7] OPERATIONAL DESCRIPTIONS1. Outline of operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-12. Scanner section . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-2

A. Scanner unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-2B. Optical system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-2

3. Laser unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-3A. Basic structure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-3B. Laser beam path. . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-3C. Composition . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-3

4. Fuser section . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-3A. General description . . . . . . . . . . . . . . . . . . . . . . . . . 7-4

5. Paper feed section and paper transport section . . . . . . 7-4A. Paper transport path and general operations . . . . . . 7-4

6. Process unit new drum detection mechanism . . . . . . . . 7-77. SPF/RSPF section . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-7

A. Outline . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7-7B. Document transport path and basic composition . . .7-8C. Operational descriptions. . . . . . . . . . . . . . . . . . . . . . 7-8D. SPF/RSPF open/close detection

(book document detection) . . . . . . . . . . . . . . . . . . . . 7-98. D-D (Duplex to Duplex) mode paper/

document transport (Duplex model) (AL-2050CS only) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-9A. Initial state . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-9B. Front copy. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-9C. Back copy . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7-10

9. Shifter (AL-2050CS only) . . . . . . . . . . . . . . . . . . . . . . .7-10

[8] DISASSEMBLY AND ASSEMBLY1. High voltage section. . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-1

A. List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-1B. Disassembly procedure . . . . . . . . . . . . . . . . . . . . . . 8-1C. Assembly procedure. . . . . . . . . . . . . . . . . . . . . . . . .8-1D. Charger wire cleaning. . . . . . . . . . . . . . . . . . . . . . . .8-1E. Charger wire replacement . . . . . . . . . . . . . . . . . . . . 8-2

2. Operation panel section . . . . . . . . . . . . . . . . . . . . . . . . .8-2A. List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-2B. Disassembly procedure . . . . . . . . . . . . . . . . . . . . . . 8-2C. Assembly procedure. . . . . . . . . . . . . . . . . . . . . . . . .8-3

3. Optical section . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-3A. List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-3B. Disassembly procedure . . . . . . . . . . . . . . . . . . . . . . 8-3C. Assembly procedure. . . . . . . . . . . . . . . . . . . . . . . . .8-5

4. Fusing section . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-5A. List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-5B. Disassembly procedure . . . . . . . . . . . . . . . . . . . . . . 8-5C. Assembly procedure. . . . . . . . . . . . . . . . . . . . . . . . .8-8

5. Tray paper feed/transport section . . . . . . . . . . . . . . . . . 8-8A. List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-8B. Disassembly procedure . . . . . . . . . . . . . . . . . . . . . . 8-8C. Assembly procedure. . . . . . . . . . . . . . . . . . . . . . . .8-14

6. Manual paper feed section. . . . . . . . . . . . . . . . . . . . . . 8-14A. List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-14B. Disassembly procedure . . . . . . . . . . . . . . . . . . . . . 8-14C. Assembly procedure. . . . . . . . . . . . . . . . . . . . . . . .8-16D. Pressure plate holder attachment. . . . . . . . . . . . . . 8-16

7. Rear frame section. . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-16A. List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-16B. Disassembly procedure . . . . . . . . . . . . . . . . . . . . . 8-16C. Assembly procedure. . . . . . . . . . . . . . . . . . . . . . . .8-17

8 Power section . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-18A. List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-18B. Disassembly procedure . . . . . . . . . . . . . . . . . . . . . 8-18C. Assembly procedure. . . . . . . . . . . . . . . . . . . . . . . .8-18

9. Duplex motor section (AL-2040CS/2050CS only) . . . . 8-18A. List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-18B. Disassembly procedure . . . . . . . . . . . . . . . . . . . . . 8-18C. Assembly procedure. . . . . . . . . . . . . . . . . . . . . . . . 8-18

10. Reverse roller section (AL-2040CS/2050CS only) . . . 8-18A. List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-18B. Disassembly procedure . . . . . . . . . . . . . . . . . . . . . 8-18C. Assembly procedure. . . . . . . . . . . . . . . . . . . . . . . . 8-18

11. RSPF section (AL-2050CS only) . . . . . . . . . . . . . . . . . 8-19A. Front cabinet, rear cabinet . . . . . . . . . . . . . . . . . . . 8-19B. Upper door unit. . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-19C. Document tray unit . . . . . . . . . . . . . . . . . . . . . . . . . 8-19D. Upper door open/close sensor . . . . . . . . . . . . . . . . 8-19E. Reverse clutch, paper exit roller. . . . . . . . . . . . . . . 8-19F. Drive unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-20G. Shutter solenoid . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-21H. Pickup roller, take-up roller. . . . . . . . . . . . . . . . . . . 8-21I. Paper empty sensor . . . . . . . . . . . . . . . . . . . . . . . . 8-22J. PS roller . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-22K. Upper transport roller . . . . . . . . . . . . . . . . . . . . . . . 8-23L. Paper sensor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-23M. Lower transport roller . . . . . . . . . . . . . . . . . . . . . . . 8-23N. Paper exit sensor . . . . . . . . . . . . . . . . . . . . . . . . . . 8-24

12. SPF section (AL-2030/2040CS only). . . . . . . . . . . . . . 8-24A. SPF motor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-24B. Pick-up roller, paper feed roller . . . . . . . . . . . . . . . 8-25C. Paper exit roller . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-26D. Set sensor, scan front sensor. . . . . . . . . . . . . . . . . 8-26E. Transport roller . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-26

13. 2nd cassette section (AL-2040CS/2050CS only) . . . . 8-27A. Paper sensor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-27B. Cassette detection switch. . . . . . . . . . . . . . . . . . . . 8-28C. Paper feed solenoid . . . . . . . . . . . . . . . . . . . . . . . . 8-28D. Transport roller . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-28E. Paper feed clutch . . . . . . . . . . . . . . . . . . . . . . . . . . 8-28F. 2nd paper feed roller . . . . . . . . . . . . . . . . . . . . . . . 8-28

[9] ADJUSTMENTS1. Optical section . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-1

A. Copy magnification ratio adjustment . . . . . . . . . . . . 9-1B. Image position adjustment . . . . . . . . . . . . . . . . . . . . 9-2

2. Copy density adjustment . . . . . . . . . . . . . . . . . . . . . . . . 9-4A. Copy density adjustment timing . . . . . . . . . . . . . . . . 9-4B. Note for copy density adjustment . . . . . . . . . . . . . . . 9-4C. Necessary tool for copy density adjustment. . . . . . . 9-4D. Features of copy density adjustment . . . . . . . . . . . . 9-4E. Copy density adjustment procedure. . . . . . . . . . . . . 9-5

3. High voltage adjustment . . . . . . . . . . . . . . . . . . . . . . . . 9-5A. Main charger (Grid bias). . . . . . . . . . . . . . . . . . . . . . 9-5B. DV bias check . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-6

4. Duplex adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9-6A. Adjusting the paper reverse position in memory

for duplex copying . . . . . . . . . . . . . . . . . . . . . . . . . . 9-6B. Adjusting trailing edge void in duplex copy mode . . 9-6

5. SPF/RSPF scan position automatic adjustment . . . . . . 9-76. SPF/RSPF mode sub scanning direction

magnification ratio adjustment . . . . . . . . . . . . . . . . . . . . 9-87. Automatic black level correction . . . . . . . . . . . . . . . . . . 9-8

[10] SIMULATION, TROUBLE CODES1. Entering the simulation mode . . . . . . . . . . . . . . . . . . . 10-12. Key rule . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-13. List of simulations . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-14. Descriptions of various simulations . . . . . . . . . . . . . . . 10-25. Trouble codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-30

A. Trouble codes list . . . . . . . . . . . . . . . . . . . . . . . . . 10-30B. Details of trouble codes . . . . . . . . . . . . . . . . . . . . 10-30

[11] USER PROGRAM1. Functions that can be set with user programs . . . . . . . 11-12. Toner save mode (AL-2030/2040CS) . . . . . . . . . . . . .11-13. User programs (AL-2030/2040CS) . . . . . . . . . . . . . . . 11-14. User programs (AL-2050CS) . . . . . . . . . . . . . . . . . . . . 11-2

A. Copy mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11-2B. Print mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11-4

[12] ELECTRICAL SECTION1. Block diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12-1

A. Overall block diagram. . . . . . . . . . . . . . . . . . . . . . .12-12. Actual wiring diagram. . . . . . . . . . . . . . . . . . . . . . . . . . 12-3

A. AL-2030 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12-3B. AL-2040CS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12-5C. AL-2050CS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12-7D. AL-2040CS/2050CS . . . . . . . . . . . . . . . . . . . . . . . .12-9

3. Signal name list . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12-9

[13] CIRCUIT DIAGRAM1. MCU PWB (AL-2030/2040CS). . . . . . . . . . . . . . . . . . . 13-12. OPERATION PWB (AL-2030/2040CS) . . . . . . . . . . . 13-143. MCU PWB (AL-2050CS) . . . . . . . . . . . . . . . . . . . . . . 13-154. OPERATION PWB (AL-2050CS). . . . . . . . . . . . . . . . 13-31

AL-2030/2040CS/2050CS GENERAL 1 - 1

[1] GENERAL

1. Major functionsConfigurations

Descriptions of itemsCPM: Copy speed (Copies Per Minute)

PPM: Print speed (Print Per Minute)

SB/MB: SB = Manual feed single bypass, MB = Manual feed multi-bypass

2 tray: Second cassette unit.

SPF: Original feed unit

R-SPF: Duplex original feed unit

Color scanner: Color scanner function

GDI printer: GDI printer function with USB

SPLC printer: SPLC printer function

E-SORT: Electronic sort function

Duplex: Auto duplex copy/print function

Shifter: Job separator function

FAX: FAX function.

Sharpdesk: Scanner utilities

IEEE1284: Interface port (parallel)

USB: Interface port (USB)

RJ45: Interface port (Network)

External NIC: Network expansion kit

Descriptions of table: Standard provision

: No function or no option available

Opt: Option

ItemCPM

(Letter)PPM

(Letter)SB/MB

2 Tray

SPFR-

SPF

Color Scanner (push)

GDI printer

SPLC printer

E-SORT

Duplex Shifter FAX Sharpdesk

IEEE1284

USB RJ45External

NICModelAL-2030 20

CPM16

PPMMB

(2.0Full)

AL-2040CS 20CPM

16PPM

MB(2.0Full)

(print only)

AL-2050CS 20CPM

20PPM

MB(2.0Hi)

(print only)

AL-2040CSAL-2030

AL-2050CS

[2] SPECIFICATIONS

1. Basic Specifications

2. Operation specifications

Item

Type Desktop

Copy system Dry, electrostatic

Segment (class) Digital personal copier

Copier dimensions AL-2030 20-1/2" (W) x 17-5/8" (D) x 14-1/8" (H) (518mm (W) x 445mm (D) x 358mm (H))AL-2040CS 20-1/2" (W) x 17-5/8" (D) x 17-5/8" (H) (518mm (W) x 445mm (D) x 445mm (H))

AL-2050CS 20-1/2" (W) x 17-5/8" (D) x 18-1/8" (H) (518mm (W) x 445mm (D) x 459mm (H))

Weight (Approximately) AL-2030 37.9 lbs. (17.2Kg) TD cartridge not included

AL-2040CS 45.9 lbs. (20.8Kg)

AL-2050CS 51.2 lbs. (23.2Kg)

Section, item Details

Paper feed section

Paper feed system

AL-2030 1 tray (250 sheet) + multi-bypass (50 sheet)

AL-2040CS/2050CS 2 tray (500 sheet) + multi-bypass (50 sheet)Inch system

Tray paper feed section

Paper size 8-1/2" x 14", 8-1/2" x 13", 8-1/2 x 11", 8-1/2" x 5-1/2" (Landscape)

Paper weight 15 - 21 lbs.Paper feed capacity 250 sheets

Kinds Standard paper, specified paper, recycled paper

Remark User adjustment of paper guide available

Multi-bypass paper feed section

Paper size Max, feedable size: 8-1/2" x 14" / Min, feedable size: 3.87" x 5.83"

Paper weight 15 - 34.5 lbs.

Paper feed capacity 50 sheets

Kinds Standard paper, specified paper, recycled paper, OHP, Label, Envelop (Single copy)


AB system Tray paper feed section

Paper size A4, B5, A5 (Landscape)

Paper weight 56 - 80g/m2 (15 - 21 lbs.)Paper feed capacity 250 sheets

Kinds Standard paper, specified paper, recycled paper


Multi-bypass paper feed section

Paper size Max, feedable size: A4 / Min, feedable size: 89 x 140mm

Paper weight 56 - 128g/m2 (15 - 34.5 lbs.)

Paper feed capacity 50 sheets

Kinds Standard paper, specified paper, recycled paper, OHP, Label, (Single copy)


Paper exit section Exit way Face downCapacity of output tray 200 sheets

Originals Original set Center Registration (left edge)

Max. original size 8-1/2" x 14" (A4)

Original kinds sheet, book

Original size detection None

Optical section

Scanning section

Scanning system 3 CCDs (RGB) sensor scanning by lighting white lampCCD sensor Resolution 600 dpi

Lighting lamp Type CCFL

Voltage 560Vrms

Power consumption 2.8W

Output data Output: R, G, B 1 or 8 bits/pixel / Input: A/D 16 bits (12 bits actual)

Writing section

Writing system Writing to OPC drum by the semiconductor laser

Laser unit Resolution 600 dpi

AL-2030/2040CS/2050CS SPECIFICATIONS 2 - 1

3. Copy performance

*1: The first-copy time is measured after the power save indicator turns off following power on, using the document glass with the polygon rotat-ing in the copy ready state and "Selection of copy start state" set to ON in the user programs (8-1/2" x 11" (A4), paper fed from paper tray).

The first-copy time may vary depending on machine operating conditions and ambient conditions such as temperature.

Image forming Photoconductor Type OPC (30ø)

Life 18kCharger Charging system Saw-tooth charging with a grid, / (-) scorotron discharge

Transfer system (+) DC corotron system

Separation system (-) DC corotron system

Developing Developing system Dry, 2-component magnetic brush development system

Cleaning Cleaning system Counter blade system (Counter to rotation)

Fusing section Fusing system Heat roller systemUpper heat roller Type Teflon roller

Lower heat roller Type Silicon rubber roller

Heater lamp Type Halogen lamp

Voltage 120V

Power consumption 800W

Electrical section Power source Voltage 120VFrequency Common use for 50 and 60Hz

Power consumption Max. Less than 1000W

Average (during copying) 350Wh/H or less (AL-2030/2040CS)

380Wh/H or less (AL-2050CS)

Average (stand-by) 80Wh/H or less

Pre-heat mode 25Wh/H or less (AL-2030/2040CS)

28Wh/H or less (AL-2050CS)

Auto power shut-off mode 8.8W or less (AL-2030/2040CS)

12.5W or less (AL-2050CS)

Section, item Details AL-2030/2040CS/2050CS

Copy magnification Fixed magnification ratios

4 Reduction + 3 Enlargement

(Inch system: 25, 50, 64, 78, 100, 129, 200, 400%)

(AB system: 25, 50, 70, 86, 100, 141, 200, 400%)Zooming magnification ratios

25 - 400% (376 steps in 1% increments)

50 - 200% when using SPF/RSPF (151 steps in 1% increments)

Manual steps (manual, photo) 5 steps

Copy speed (CPM) First-copy time *1 (Approximately)

AL-2030/2040CS:

8.0 seconds (When user program 24 is set to OFF)

AL-2050CS:

10.7 seconds

(paper: A4 (8-1/2" x 11"), exposure mode: AUTO, copy ratio: 100%)

Inch system

8-1/2" x 11" (Landscape)

Same size 20

AB system

A4 (Landscape)

Same size 20

AB system

B5 (Landscape)

Same size 20

Max. continuous copy quantity 99Void Void area Leading edge 1 - 4mm

Trailing edge 4mm or less

Side edge void area 0.5mm or more (per side)

4.5mm or less (total of both sides)

Image loss Leading edge same size: 3.0mm or less (OC) / 4mm or less (SPF/RSPF)

Enlarge: 1.5mm or less (OC) / 3mm or less (SPF/RSPF)

Reduction (50%): 6.0mm or less (OC) / 8mm or less (SPF/RSPF)

Warm-up time 0 sec. Immediately the ready lamp is lit.

Power save mode reset time 0 sec. Immediately the ready lamp is lit.Paper jam recovery time 0 sec.

∗ Jam recovery condition: Recovery time from 60 sec of door open.

Section, item Details


4. GDI Printer (AL-2030/2040CS)

*1: Engine Resolution

*2: By running change

5. SPLC printer (AL-2050CS only)

*1: Engine Resolution

*2: Running change

6. Scan function


Print speed Max. 16ppm (excluding bypass tray, paper size A4, 8.5" x 11") (Variable depending on the PC performance)Duplex Yes (AL-2040CS only)

Memory 8MB (Duplex model: 16MB)

Interface USB 2.0 (Full speed) (AL-2040CS only)

Network Built-in NIC (10 Base) (AL-2040CS only)

Emulation GDI

MIB support NoResolution 600dpi *1

Supported OS Windows 98/Me, Windows 2000 Professional, Windows XP Home Edition/Professional, Windows Vista *2

WHQL support Yes *2

Application Status window

Print speed Max. 20ppm (Paper size: A4, excluding manual paper feed)

∗ Varies depending on the PC performance.

First print time 8 sec. (without data transfer time)

Duplex Yes

ROPM Yes

Memory 64MB

Interface USB2.0 (Hi Speed)Network Built-in NIC (10 Base)

Emulation SPLC (JBIG GDI)

MIB support No

Resolution 600dpi *1

Supported OS Windows 98/Me, Windows 2000 Professional, Windows XP Home Edition/Professional, Windows Vista

WHQL support Yes *2Application Status window

AL-2030/2040CS AL-2050CS

Type Flat Bed Color Scanner

Scanning system Original table/SPF Original table/RSPF

Light source 3 CCDs (RGB) sensor scanning by lighting white lamp (2 pcs of CCFL)Resolution Optical: 600 x 1200dpi

Setting range: 50 - 9600dpi (Preview resolution is fixed at 75dpi)

Originals Sheet type / Book type

Output data R, G, B 1 or 8 bits/pixel

Scan range OC / SPF : 8.5" (H) x 14.0" (V)

Original position: Left Center

OC / RSPF : 8.5" (H) x 14.0" (V)

Original position: Left Center

Scan speed OC / SPF : Max. 2.88ms/line OC / RSPF : Max. 2.88ms/line

Protocol TWAIN / WIA (XP, Vista) / STIInterface USB2.0 (Full speed support) USB2.0 (Hi speed support)

Scanner utility Button Manager / Sharpdesk / Composer

Scan key/lamp Yes

Duplex scan No Yes

Supported OS Win 98 / Me / 2000 / XP / Vista *1

Void area No (User settable by PC)WHQL supported Yes *1


7. SPF (AL-2030/2040CS)

8. RSPF (AL-2050CS)

[Conditions] Speed with tray 1, normal size, paper size of 8.5" x 11" (A4), and RSPF.

*1: Indicates the speed from 1st to 30th sheet (i.e., 60th surface).

Original capacity 50 sheets (15 - 23.9 lbs.) (56 - 90g/m2) Stacking Height: less than 6.5mm or 1/4"Original size 8-1/2" x 14" to 5-1/2" x 8-1/2" / A4 to A5 (Landscape)

Original replacement speed 8-1/2" x 11" about 14 sheets (70%)

A4 about 14 sheets (70%)

Original placement Face up

Original weight 15 - 23.9lbs. (56 - 90g/m2)

Mixed feeding (Paper size) No

Original which cannot Thermal papers, originals with punch holes for files, be used folded paper, transparent originals such as OHP films, stapled or clip used originals with cover up liquid used, Originals with tape sealed, originals with high level frictional coefficient such as photos or catalogs.

Original capacity 50 sheets (56 - 90g/m2) or 6.5mm, 1/4" or less.

Original size 8-1/2" x 14" to 5-1/2" x 8-1/2" / A4 to A5 (Landscape)

Original replacement speed 8-1/2" x 11" about 14 sheets (70%)

A4 about 13 sheets (65%)

Job speed (Tray1, Landscape) Single copy S to S About 14CPM (8-1/2" x 11") About 13CPM (A4)

S to D About 10CPM (1 - 30 sheets)(*1) About 5.6CPM (31 sheets ~)

D to S About 6CPMD to D About 6CPM (1 - 30 sheets)(*1) About 5.6CPM (31 sheets ~)

Multi copy S to S About 20CPM

S to D About 13CPM (1 - 30 sheets)(*1) About 5.6CPM (31 sheets ~)

D to S About 16CPM

D to D About 13CPM (1 - 30 sheets)(*1) About 5.6CPM (31 sheets ~)

Original placement Face upOriginal weight 15 - 23.9lbs. (56 - 90g/m2)

Mixed feeding No

Original which cannot Thermal papers, originals with punch holes for files, be used folded paper, transparent originals such as OHP films, stapled or clip used originals with cover up liquid used, Originals with tape sealed, originals with high level frictional coefficient such as photos or catalogs.


[3] CONSUMABLE PARTS

1. Supply system tableA. SEC/SECL (AL-2030/2040CS/2050CS)

B. Brazil (AL-2030/2040CS)

2. EnvironmentalThe environmental conditions for assuring the copy quality and the machine operations are as follows:

(1) Normal operating conditionTemperature: 20°C - 25°C

Humidity: 65 ± 5%RH

(2) Acceptable operating condition

(3) Transport condition

(4) Supply storage condition

No. Name Content Life Product name Package1 Develop cartridge (Black) x 1 Toner/developer cartridge x 1 6K

(5% document)

AL-100TD 5

2 Develop cartridge (Black) x 1 Toner/developer cartridge x 1 4K

(5% document)

AL-110TD 5

3 Drum cartridge Drum cartridge 18K AL-100DR 5

No. Name Content Life Product name Package

1 Develop cartridge (Black) Toner/developer cartridge x 1

Warranty card x 1

IC-Chip: No Stirring function: Yes

6K

(A4 5% document)

AL-100TDN 5

2 Drum cartridge Drum cartridge x 1

Warranty card x 1

18K

(A4 5% document)

AL-100DR 5

Humidity (RH)

85%

60%

20%

10˚C 30˚C 35˚C

Humidity (RH)

90%

60%

15%

–25˚C 30˚C 40˚C

Humidity (RH)

90%

20%

–5˚C 45˚C

AL-2030/2040CS/2050CS CONSUMABLE PARTS 3 - 1

3. Production control number (lot No.) identification<Developing cartridge>

∗ Destination

<Drum cartridge>

The label on the drum cartridge shows the date of production.

(SOCC production)

<JAPAN production> *1: The production control label is not attached to the cartridge ofa China product.

Division No.EX Destination A same pack G

B same pack H

Option Destination A P

B Q

Division No.

Ex production 1

Option 2

Same pack 3

Production month

Production day

Destination code

(Dealer, distributor, OEM, etc.)

Production place

(SOCC: Fixed to B.)

End digit of year

Version No.

Production month

Production day

Destination code

(Dealer, distributor, OEM, etc.)

Production place

(SOCC: Fixed to B.)

End digit of year

Version No.

X000119Ver.A 1

Production month

(1 - 9 = Jan. - Sep. 0 = Oct. X = Nov. Y = Dec.)

Serial number of month

Fixed to 1.

Pack division

(See table below)

End digit of year

Version No.

Production controllabel attachment position

Production controllabel attachment position(*1)

AL-2030/2040CS/2050CS CONSUMABLE PARTS 3 - 2

[4] EXTERNAL VIEWS AND INTERNAL STRUCTURES

1. Appearance

2. Internal

1 Document glass 2 Operation panel 3 Front cover4 Paper tray 1 5 Paper tray 2 (AL-2040CS/2050CS only) 6 Multi-bypass tray

7 Side cover 8 Side cover open button 9 Bypass tray paper guides

10 Paper output tray 11 Paper output tray extension 12 Power switch

13 Handle 14 Power cord

1 Front cover 2 Side cover 3 Fusing unit release lever4 Transfer charger 5 Charger cleaner

LAN connector (AL-2040CS/2050CS only)

Interface

USB connector(AL-2030/2040CS)

Interface

SPF/RSPF

Exit area

2

3

4

5

1

7

98

1011

Original guide

Document feeder tray

Peep hole (SPF only)

Document feeder cover

12

1314

6

USB connector(AL-2050CS

TD cartridge Drum cartridge

3

4

5

2

1

AL-2030/2040CS/2050CS EXTERNAL VIEWS AND INTERNAL STRUCTURES 4 - 1

3. Operation panelA. AL-2030/2040CS

*1: Drum cartridge replacement

The useful life of the drum cartridge is approximately 18,000copies*. When the internal counter reaches approximately17,000 copies, the drum replacement required ( ) indicatorwill light up indicating that replacement of the drum cartridgewill be needed soon. For more information on purchasing thedrum cartridge, please refer to the Operation Manual. When theindicator begins to blink, the unit will stop operating until the car-tridge is replaced. Replace the drum cartridge at this time.

*: Based on copying onto letter size paper at 5% toned area.

*2: TD cartridge replacement

The TD cartridge replacement required ( ) indicator will lightup when toner is needed. For more information on purchasingthe TD cartridge. If copying is continued while the indicator is lit,copies will gradually become lighter until the unit stops and theindicator begins blinking.

*3: Indicators on the operation panel

The ONLINE indicator and the start ( ) indicator indicate thestate of the printer or scanner.

Start indicator

1 Original to copy key and indicators (AL-2040CS only) 2 Exposure mode selector key and indicatorsUse to sequentially select the exposure modes: AUTO, MANUAL or PHOTO.

Selected mode is shown by a lit indicator.

Two-sided copies from one-sided originals.

Turn on Long Edge or Turn on Short Edge can be selected.

3 Light and dark keys and indicatorsUse to adjust the MANUAL or PHOTO exposure level. Selected exposure level is shown by a lit indicator. Use to start and terminate user program setting.

4 Alarm indicatorsDrum replacement required indicator *1

Misfeed indicator

TD cartridge replacement required indicator *25 SPF indicator 6 SPF misfeed indicator7 Copy ratio selector key and indicators

Use to sequentially select preset reduction/enlargement copy ratios.

Selected copy ratio is shown by a lit indicator.

8 Copy ratio display (%) key• Use to verify a zoom setting without changing the zoom ratio.• Use to check the number of originals that must be returned to

the document feeder tray if an original misfeed occurs whileusing the SPF.

9 DisplayDisplays the specified copy quantity, zoom copy ratio, user program code, and error code.

10 SCAN key and indicator (AL-2040CS only) *3, *4

11 ONLINE key and indicatorLights up when the unit is used as a printer and scanner (AL-2040CS only). *3

12 Start key and indicator• Copying is possible when the indicator is on.• Press to start copying• Use to set a user program.

13 Power save indicatorLights up when the unit is in a power save mode.

14 Tray select keyUse to select a paper feed station (paper tray 1, paper tray 2 (AL-2040CS only) or multi-bypass tray).

15 Paper feed location indicatorsLight up to show the selected paper feed station.

16 ZOOM keys and indicatorUse to select any reduction or enlargement copy ratio from 25% to 400% in 1% increments. (When the SPF is being used, the zoom copy ratio range is 50% to 200%.)

17 Copy quantity keys• Use to select the desired copy quantity (1 to 99).• Use to make user program entries.

18 Clear key• Press to clear the display, or press during a copy run to

terminate copying.• Press and hold down during standby to display the total

number of copies made to date.

1 2 3 4 5 6 7 8 9 10 11 12 13

14 15 16 17 18

On: Indicates the unit is ready for copying or scanning isbeing performed.

Blinking: The indicator blinks in the following situations:

• When a print job is interrupted.

• When reserving a copy job.

• When toner is being replenished during a copy orprint job.

Power save indicator

Start indicatorONLINE indicator

SCAN indicator


ONLINE indicator

The ONLINE key is pressed and on line and off line arechanged.

Power save indicator

SCAN indicator (AL-2040CS only)

*4: Using the SCAN key to begin scanning

Note:

• Scanning is not possible during a copy job.

• If the SCAN ( ) key is pressed during a print job, the scanjob will be stored.

• When scanning an original that has been placed in the SPF,only one original can be placed unless you are using Sharp-desk.

1) Press the SCAN ( ) key.

The unit enters scan mode.

2) Place the original you wish to scan on the document glass/SPF.

3) Press the right copy quantity key to display the number ofthe application that you wish to use for scanning.

The application numbers are initially as follows.

4) Press the start ( ) key.

Scanning will start and the scanned data will be transferredto the application.

B. AL-2050CS

Off: The indicator is off in the following situations:

• During copying or scanning.

• The unit is in the auto power shut-off mode.

• When a misfeed or error has occurred.

On: Indicates the unit is ready for printing or scanning is being performed. (On line)

Blinking: Printing or data is being received from a computer.Off: Copying is being performed. (Off line)

On: Indicates the unit is in a power save mode.Blinking: Indicates that the unit is initializing (when the side

cover is opened and closed or the power turned off and on).

On: The SCAN ( ) key has been pressed and the unit is in scanner mode.

Blinking: A scan job is being executed from the computer, or scan data is stored in the unit’s memory.

Off: The unit is in the copy mode.

Application number

Application launched

SC1 Sharpdesk (Full color) (if installed)

SC2 Sharpdesk (Monochrome) (if installed)

SC3 E-mail (your standard e-mail program in the Windows OS you are using)

SC4 Fax (if a fax program is installed)

SC5 OCR (if an OCR program is installed)

SC6 Microsoft Word (if installed)

1 [MODE SELECT] key / Mode indicatorsPress this key to select the mode. The indicator of the selected mode lights (copy, printer, scanner indicators).

2 DisplayThis shows messages indicating the machine status and any problems that occur, as well as user programs and function setting menus.

3 Numeric keysUse these to enter the number of copies and other numerical settings.

The keys can also be used to select items in function setting menus.

4 [CLEAR] key ( )Use this to clear the set number of copies, as well as cancel a job that is in progress. When a setting menu appears, use this key to move back to the previous menu level.

5 Power save indicatorThis lights up when the power save function is activated.

6 RSPF indicatorThis lights up when an original is placed in the RSPF.

7 Error indicatorThis lights steadily or blinks when a paper misfeed or other error occurs.

8 [TRAY SELECT] key ( )Use to select the paper tray that has the desired paper for copying.

1 2 3 4 5

6 7 8 10 11 1312 14 159 16 17

READY TO COPY. 100% 8.5x11 0

Display

18 19 20 21


9 Tray location indicatorIndicates the selected paper tray. The indicator blinks when the tray is out of paper during operation or is not closed properly.

10 [MENU] keyPress this key to select the paper size for copying, to configure a user program or to display the total count.

11 [2-SIDED COPY] keyPress to select the automatic two-sided copying mode.

12 [E-SORT/SP.FUN] keyPress to select the sort function, 2 IN 1 copy function, or margin shift function.

13 [ ] key ( ), [ ] key ( ), [ENTER] keyPress the [ ] key ( ) or [ ] key ( ) to select an item in a function setting menu.

Press the [ENTER] key to enter a selection.

14 [EXPOSURE] keyUse to switch from auto exposure adjustment to text mode or photo mode.

15 [COPY RATIO] keyPress to select an enlargement or reduction ratio.

To select a preset ratio setting, press the [COPY RATIO] key and select the desired preset ratio. To select a ratio that is not preset, press the [COPY RATIO] key, select the preset ratio that is closest to the desired ratio, and then press the [ ] key ( ) or [ ] key ( ) to increase or decrease the ratio in increments of 1%.

16 [CLEAR ALL] key ( )This returns all functions to the default settings. When pressed in a setting menu, this returns the settings and display to the initial state.

17 [START] key ( ) / Ready indicatorThe ready indicator lights up when copying or scanning is possible.

To begin copying, press the [START] key ( ).

The [START] key ( ) is also pressed to return to normal operation from auto power shut-off mode.

18 Shows the current copy ratio.

19 Shows the selected paper size. 20 Shows the number of copies that has been entered with the numeric keys.

21 A checkmark " " appears when the exposure has been changed, or when two-sided copying, sort, 2 IN 1, or margin shift is selected.


4. Motors and solenoidsA. AL-2030/2040CS

3

9

2

8

4

1

5

7

10

6

No. Part name Control signal Function / Operation1 Main motor MM Drives the copier.2 Scanner motor MRMT Drives the optical mirror base (scanner unit).3 Toner motor TM Supplies toner.4 Cooling fan motor VFM Cools the optical, fusing section.5 Resist roller solenoid RRS Resist roller rotation control solenoid6 Paper feed solenoid CPFS1 Cassette Paper feed solenoid 17 Multi paper feed solenoid MPFS Multi manual pages feed solenoid8 SPF motor SPFM Drives the single pass feeder9 Duplex motor DMT Devices the duplex paper transport section (AL-2040CS only)

10 Paper feed solenoid CPFS2 Cassette Paper feed solenoid 2 (AL-2040CS only)


B. AL-2050CS

12

13

8

1

4

2

5

61011

7

3

9

No. Part name Control signal Function / Operation1 Main motor MM Drives the copier.2 Scanner motor MRMT Drives the optical mirror base (scanner unit).3 Toner motor TM Supplies toner.4 Cooling fan motor VFM Ventilate the fuser section.5 Resist roller solenoid RRS Resist roller rotation control solenoid6 Paper feed solenoid CPFS1 Cassette Paper feed solenoid 17 Multi paper feed solenoid MPFS Multi manual pages feed solenoid8 Drive motor SPMT Drives the RSPF.9 Duplex motor DMT Devices the duplex paper transport section

10 Paper feed solenoid CPFS2 Cassette Paper feed solenoid 211 Shifter motor SFTM Drives the shifter.12 Reverse clutch SRVC Reverses the rotating direction of the roller.13 Paper feed solenoid (RSPF) SPUS Feeds paper.


5. Sensors and switchesA. AL-2030/2040CS

(For the AL-2030, the 2nd cassette is not provided.)

1 2

8

9

3

4

10

5

116

7

No. Name Signal Type Function Output1 Scanner unit home position

sensorMHPS Transmission sensor Scanner unit home position detection "H" at home position

2 POD sensor POD Transmission sensor Paper exit detection "H" at paper pass3 PPD2 sensor PPD2 Transmission sensor Paper transport detection 2 "L" at paper pass4 Cassette detection switch CED1 Micro-switch Cassette installation detection "H" at cassette insertion5 PPD1 sensor PPD1 Transmission sensor Paper transport detection 1 "L" at paper pass6 Door switch DSW Micro-switch Door open/close detection

(safety switch for 24V)1 or 0V of 24V at door open

7 Drum reset switch DRST Micro-switch New drum detection switch Instantaneously "H" at insertion of new drum

8 SPF sensor SPID/SD SW

Transmission sensor Paper entry detection

Cover open/close detection

"L" at paper pass

9 SPPD sensor SPPD Transmission sensor Paper transport detection "L" at paper pass10 2nd cassette DSW Micro-switch 2nd cassette door open detection

(AL-2040CS only)1 or 0V of 5V at door open

11 PPD3 sensor PPD3 Transmission sensor Paper transport detection 3 "L" at paper pass


B. AL-2050CS

1

3

4

2

8 9

13

12

5

6

10

7 11

No. Name Signal Type Function Output1 Scanner unit home position

sensorMHPS Transmission sensor Scanner unit home position detection "H" at home position

2 POD sensor POD Transmission sensor Paper exit detection "H" at paper pass3 PPD2 sensor PPD2 Transmission sensor Paper transport detection 2 "L" at paper pass4 Cassette detection switch CED1 Micro-switch Cassette installation detection "H" at cassette insertion5 PPD1 sensor PPD1 Transmission sensor Paper transport detection 1 "L" at paper pass6 Door switch DSW Micro-switch Door open/close detection

(safety switch for 24V)1 or 0V of 24V at door open

7 Drum reset switch DRST Micro-switch New drum detection switch Instantaneously "H" at insertion of new drum

8 Paper empty sensor SPID Transmission sensor Paper entry detection "H" paper empty9 Paper exit sensor SRJD Transmission sensor Paper exit detection "H" paper empty

10 2nd cassette DSW Micro-switch 2nd cassette door open detection 1 or 0V of 5V at door open11 PPD3 sensor PPD3 Transmission sensor Paper transport detection 3 "L" at paper pass12 Paper sensor SPPD Transmission sensor Paper transport detection "H" paper empty13 Upper door open/close sensor SCOD Transmission sensor Cover open/close detection "L" open


6. PWB unitA. AL-2030/2040CS

2

4

5

8

3

6

7

9

10

1

No. Name Function1 Exposure lamp invertor PWB Exposure lamp (CCFL) control2 Main PWB (MCU) Copier control3 Operation PWB Operation input/display4 High voltage PWB High voltage control5 CCD sensor PWB For image scanning6 LSU motor PWB For polygon motor drive7 TCS PWB For toner sensor control8 LSU PWB For laser control9 NIC PWB Network print control (AL-2040CS only)

10 Power PWB AC power input, DC voltage control


B. AL-2050CS

1

5 2

8

6

37

4

10

9

No. Name Function1 Exposure lamp invertor PWB Exposure lamp (CCFL) control2 Main PWB (MCU) Copier control3 Operation PWB Operation input/display4 High voltage PWB High voltage control5 CCD sensor PWB For image scanning6 LSU motor PWB For polygon motor drive7 TCS PWB For toner sensor control8 LSU PWB For laser control9 NIC PWB Network print control

10 Power PWB AC power input, DC voltage control


7. Cross sectional viewA. AL-2030/2040CS

3

4

5

8

9

10

11

6

7

121314

1

2

15 16

17

18

No. Part name Function and operation1 Scanner unit Illuminates the original with the copy lamp and passes the reflected light to the lens unit (CCD).2 Exposure lamp Exposure lamp (CCFL) Illuminates original3 LSU (Laser unit) Converts the original image signal into laser beams and writes onto the drum.4 Paper exit roller Roller for paper exit5 Main charger Provides negative charges evenly to the drum surface.6 Heat roller Fuses toner on the paper. (Teflon roller)7 Pressure roller Fuses toner on the paper. (Silicon rubber roller)8 Drum Forms images.9 Transfer unit Transfers images onto the drum.

10 Pickup roller Picks up the manual feed paper. (In multi feed only)11 Manual paper feed tray Tray for manual feed paper12 Manual paper feed roller Transport the paper from the manual paper feed port.13 PS roller unit Takes synchronization between the lead edge and the rear edge of the paper.14 Paper feed roller Picks up a sheet of paper from the cassette.15 Pickup roller Picks up documents.16 Separation roller Separates documents to feed properly.17 PS roller Feeds documents to the scanning section.18 Paper exit roller Discharges documents.


B. AL-2050CS

2019

15 16 1718

6

7

8

9

10

11

12

41 2

53

14 13

No. Part name Function and operation1 Scanner unit Illuminates the original with the copy lamp and passes the reflected light to the lens unit (CCD).2 Exposure lamp Exposure lamp (CCFL) Illuminates original3 LSU (Laser unit) Converts the original image signal into laser beams and writes onto the drum.4 Paper exit roller Roller for paper exit5 Main charger Provides negative charges evenly to the drum surface.6 Heat roller Fuses toner on the paper. (Teflon roller)7 Pressure roller Fuses toner on the paper. (Silicon rubber roller)8 Drum Forms images.9 Transfer unit Transfers images onto the drum.

10 Pickup roller Picks up the manual feed paper. (In multi feed only)11 Manual paper feed tray Tray for manual feed paper12 Manual paper feed roller Transport the paper from the manual paper feed port.13 PS roller unit Takes synchronization between the lead edge and the rear edge of the paper.14 Paper feed roller Picks up a sheet of paper from the cassette.15 Pickup roller Picks up documents.16 Separation roller Separates documents to feed properly.17 Upper transport roller Transports of a document.18 Paper exit roller Discharges documents.19 Lower transport roller Transports of a document.20 PS roller Feeds documents to the scanning section.


[5] UNPACKING AND INSTALLATION

1. Copier installationImproper installation may damage the copier. Please note the fol-lowing during initial installation and whenever the copier is moved.

Caution: If the copier is moved from a cool place to a warm place,condensation may form inside the copier. Operation in thiscondition will cause poor copy quality and malfunctions.Leave the copier at room temperature for at least 2 hoursbefore use.

Do not install your copier in areas that are:

• damp, humid, or very dusty

• exposed to direct sunlight

• poorly ventilated

• subject to extreme temperature or humidity changes, e.g., nearan air conditioner or heater.

The copier should be installed near an accessible power outlet foreasy connection.

Be sure to connect the power cord only to a power outlet that meetsthe specified voltage and current requirements.

Also make certain the outlet is properly grounded.

Be sure to allow the required space around the machine for servic-ing and proper ventilation.

2. Cautions on handlingBe careful in handling the copier as follows to maintain the perfor-mance of this copier.

Do not drop the copier, subject it to shock or strike it against anyobject.

Do not expose the drum cartridge to direct sunlight.

Doing so will damage the surface (green portion) of the drum car-tridge, causing poor print quality.

Store spare supplies such as drum cartridges and TD cartridges ina dark place without removing from the package before use.

If they are exposed to direct sunlight, poor print quality may result.

Do not touch the surface (green portion) of the drum cartridge.

Doing so will damage the surface of the cartridge, causing poorprint quality.

3. Checking packed components and accessories

Open the carton and check if the following components and acces-sories are included.

8" (20cm)8" (20cm)

4"(10cm)

4"(10cm)

Operation manual

Software CD-ROM

TD cartridge

Drum cartridge(installed in unit)

AL-2030/2040CS/2050CS UNPACKING AND INSTALLATION 5 - 1

4. UnpackingBe sure to hold the handles on both sides of the unit to unpack theunit and carry it to the installation location.

5. Removing protective packing materials

1) Remove all pieces of tape shown in the illustration below. Thenopen the SPF/RSPF and remove protective materials. Afterthat, take out the bag containing the TD cartridge.

2) Release the scan head locking switch.

The scan head locking switch is under the document glass.

If the switch is locked ( ), the unit will not operate. Unlock theswitch ( ) as shown below.

To lock the scan head locking switch, hold up the catch in illus-tration (A) and turn the center knob counter-clockwise 90degrees until you hear a click.

6. Installing the TD cartridge1) Open the multi-bypass tray, and then open the side cover.

2) Remove the CAUTION tape from the front cover and removethe two protective pins from the fusing unit by pulling the stringsupward one at a time.

3) Push gently on both sides of the front cover to open the cover.

4) Remove the TD cartridge from the bag. Remove the protectivepaper. Hold the cartridge on both sides and shake it horizontallyfour or five times. Hold the tab of the protective cover and pullthe tab to your side to remove the cover.

5) Gently insert the TD cartridge until it locks in place while push-ing the lock release button.

6) Close the front cover and then the side cover by pressing theround projections near the side cover open button.

Caution: When closing the covers, be sure to close the front coversecurely and then close the side cover. If the covers areclosed in the wrong order, the covers may be damaged.

AL-2030

AL-2040CS/2050CS

(A)

Lock Unlock

Grasp here and turn in the direction of the arrow.

CAUTION tape

Protective pins

4 or 5 times

Lock release button


7. Loading paper1) Raise the handle of the paper tray and pull the paper tray out

until it stops.

2) Remove the pressure plate lock. Rotate the pressure plate lockin the direction of the arrow to remove it while pressing downthe pressure plate of the paper tray.

3) Store the pressure plate lock which has been removed in step2). To store the pressure plate lock, rotate the lock to fix it on therelevant location.

4) Adjust the paper guides on the paper tray to the copy paperwidth and length. Squeeze the lever of paper guide (A) andslide the guide to match with the width of the paper. Move paperguide (B) to the appropriate slot as marked on the tray.

5) Fan the paper and insert it into the tray. Make sure the edges gounder the corner hooks.

Note: Do not load paper above the maximum height line ( ).Exceeding the line will cause a paper misfeed.

6) Gently push the paper tray back into the unit.

8. Power to copierEnsure that the power switch of the unit is in the OFF position. Plugthe other end of the power cord into the nearest outlet. Turn thepower switch on the left side of the unit to the "ON" position. Thestart ( ) indicator will light up and other indicators which show theinitial settings of the operation panel will also light up to indicate theready condition.

9. SoftwareThe CD-ROM that accompanies the machine contains the followingsoftware:

Printer driver (AL-2030)The printer driver enables you to use the printer function of themachine.

The printer driver includes the Print Status Window. This is a utilitythat monitors the machine and informs you of the printing status,the name of the document currently being printed, and error mes-sages.

Please note that the printing over a network connection is not possi-ble.

MFP driver (AL-2040CS/2050CS)Printer driver

The printer driver enables you to use the printer function of themachine.

The printer driver includes the Print Status Window. This is a utilitythat monitors the machine and informs you of the printing status,the name of the document currently being printed, and error mes-sages.

Please note that the Print Status Window does not operate whenthe machine is used as a network printer.

Scanner driver*

The scanner driver allows you to use the scanning function of themachine with TWAIN-compliant and WIA-compliant applications.

Sharpdesk* (AL-2040CS/2050CS)Sharpdesk is an integrated software environment that makes iteasy to manage documents and image files, and launch applica-tions.

Button Manager* (AL-2040CS/2050CS)Button Manager allows you to use the scanner menus on themachine to scan a document.

*: The scanning feature can only be used with computers that areconnected to the machine by a USB cable. If you are connectedto the machine by a LAN connection, only the printer function canbe used.

A. Before installation

Hardware and software requirementsCheck the following hardware and software requirements in order toinstall the software.

Pressure plate lock

Paper guide (B)Paper guide (A)

Computer type

IBM PC/AT or compatible computer equipped with a USB 2.0*1/1.1*2 or 10Base-T LAN interface

Operating system*3 *4

Windows 98, Windows Me, Windows 2000 Professional*5, Windows XP*5, Windows Vista*5

Display 800 x 600 dots (SVGA) display with 256 colors (or better) (AL-2030/2040CS)

1024 x 768 dots resolution and 16-bit color or higher is recommended. (AL-2050CS)

Hard disk free space

150 MB or more

Other hardware requirements

An environment on which any of the operating systems listed above can fully operate


*1: The machine’s USB connector will transfer data at the speedspecified by the USB 2.0 (Hi-Speed) only if the Microsoft USB2.0 driver is installed in the computer.

*2: Compatible with Windows 98, Windows Me, Windows 2000Professional, Windows XP or Windows Vista preinstalled modelstandardly equipped with a USB port.

*3: Printing is not available in MS-DOS mode.

*4: The machine does not support printing from a Macintosh envi-ronment.

*5: Administrator’s rights are required to install the software usingthe installer.

Installation environment and usable softwareThe following table shows the drivers and software that can beinstalled for each version of Windows and interface connectionmethod.


*2: The printer driver that is installed will vary depending on thetype of connection between the machine and your computer.

*3: Although it is possible to install Button Manager and Sharpdeskon Windows 98/Me/2000/XP/Vista, neither Button Manager northe scanner function of Sharpdesk can actually be used. (AL-2030/2040CS)

B. Installing the softwareNote:

• If you need to use a different connection method after installingthe software using a USB or network connection, you must firstuninstall the software and then install it using the new connectionmethod.

• In the following explanations it is assumed that the mouse is con-figured for right hand operation.

• The scanner function only works when using a USB cable.

• If an error message appears, follow the instructions on the screento solve the problem. After the problem is solved, the installationprocedure will continue. Depending on the problem, you mayhave to click the "Cancel" button to exit the installer. In this case,reinstall the software from the beginning after solving the prob-lem.

(1) Using the machine with a USB connection1) The USB cable must not be connected to the machine. Make

sure that the cable is not connected before proceeding.

If the cable is connected, a Plug and Play window will appear. Ifthis happens, click the "Cancel" button to close the window anddisconnect the cable.

Note: The cable will be connected in step 13).

2) Insert the CD-ROM into your computer’s CD-ROM drive.

3) Click the "start" button, click "My Computer", and then double-click the CD-ROM icon.

• In Windows Vista, click the "Start" button, click "Computer",and then double-click the CD-ROM icon.

• In Windows 98/Me/2000, double-click "My Computer", andthen double-click the CD-ROM icon.

4) Double-click the "setup" icon.

In Windows Vista, if a message screen appears asking you forconfirmation, click "Allow".

5) The "SOFTWARE LICENSE" window will appear. Make surethat you understand the contents of the software license, andthen click the "Yes" button.

Note: You can show the "SOFTWARE LICENSE" in a differentlanguage by selecting the desired language from thelanguage menu. To install the software in the selectedlanguage, continue the installation with that languageselected.

6) Read the "Readme First" in the "Welcome" window and thenclick the "Next" button.

(AL-2030)

7) To install all of the software, click the "Standard" button and goto step 12).

To install particular packages, click the "Custom" button and goto next step.

8) Click the "Printer Driver" button.

Click the "Display Readme" button to show information on pack-ages that are selected.

9) Select "Connected to this computer" and click the "Next" button.

Follow the on-screen instructions.

When "The installation of the SHARP software is complete."appears, click the "OK" button and go to step 12).

Caution:

• If you are using Windows Vista and a security warning win-dow appears, be sure to click "Install this driver software any-way".

• If you are running Windows 2000/XP and a warning messageappears regarding the Windows logo test or digital signature,be sure to click "Continue Anyway" or "Yes".

CableOperating

systemPrinter driver

Scanner driver

Button Manager

Sharpdesk

USB Windows 98/Me/2000/XP/Vista*1

Available*2 Available

LAN Windows 98/Me/2000/XP/Vista*1

Not Available*3


(AL-2040CS/2050CS)

7) To install all of the software, click the "Standard" button and goto step 12).

To install particular packages, click the "Custom" button and goto next step.

8) Click the "MFP Driver" button.


9) The files required for installation of the MFP driver are copied.


When "The installation of the SHARP software is complete."appears, click the "OK" button.

Caution:



10) You will return to the window of step 8). If you wish to install But-ton Manager or Sharpdesk, click the "Utility Software" button.

If you do not wish to install the Utility Software, click the "Close"button and go to step 12).

Note: After the installation, a message prompting you to restartyour computer may appear. In this case, click the "Yes"button to restart your computer.

Installing the Utility Software

11) Click the "Button Manager" or the "Sharpdesk" button.



Caution: In Windows 98/Me/2000, if the following screenappears, click the "Skip" button or the "Continue" but-ton as appropriate to continue the Sharpdesk installa-tion.

If "Skip" is selected, the Sharpdesk installation willcontinue without installing Sharpdesk Imaging.

If "Continue" is selected, Sharpdesk Imaging will beinstalled. If Imaging for Windows is installed on yourcomputer, Sharpdesk Imaging will overwrite Imagingfor Windows.

12) When installing is finished, click the "Close" button.

Caution:



A message will appear instructing you to connect the machineto your computer. Click the "OK" button.


13) Make sure that the power of the machine is turned on, and thenconnect the USB cable (p.5-6).

Windows will detect the machine and a Plug and Play screenwill appear.

14) Follow the instructions in the plug and play window to install thedriver.


Caution:




Note: A "USB 2.0 Composite Device" installation window mayappear prior to this procedure. In this case, follow theinstructions in the window to install the USB 2.0Composite Device.

This completes the installation of the software.

• If you installed Button Manager, set up Button Manager asexplained in "Setting up the Button Manager" (p.5-9).

• If you installed Sharpdesk, the Sharpdesk setup screen willappear. Follow the instructions in the screen to set up Sharpdesk.

(2) Connecting a USB cableFollow the procedure below to connect the machine to your com-puter.

A USB cable for connecting the machine to your computer is notincluded with the machine. Please purchase the appropriate cablefor your computer.

Caution:

• USB is available with a PC/AT compatible computer that was orig-inally equipped with USB and had Windows 98, Windows Me,Windows 2000 Professional, Windows XP Professional or Win-dows XP Home Edition preinstalled.

• Do not connect the USB cable before installing the printer driver.The USB cable should be connected during installation of theprinter driver.

1) Insert the cable into the USB connector on the machine.

2) Insert the other end of the cable into your computer’s USB port.

(3) Using the machine as a network printer (AL-2040CS/2050CS only)

Note:

• Interface cables for connecting the machine to your computer arenot included with the machine. Please purchase the appropriatecable for your computer.

• If you intend to use the machine as a scanner, it must be con-nected to your computer with a USB interface cable. The scannerfunction cannot be used if the machine is connected with a LANcable.

1) Insert the LAN cable into the LAN connector on the machine.

Use a network cable that is shielded.

2) Turn on the machine.

3) Insert the CD-ROM into your computer's CD-ROM drive.

4) Click the "start" button, click "My Computer", and then double-click the CD-ROM icon.

• In Windows Vista, click the "Start" button, click "Computer",and then double-click the CD-ROM icon.

• In Windows 98/Me/2000, double-click "My Computer", andthen double-click the CD-ROM icon.

5) Double-click the "setup" icon.

In Windows Vista, if a message screen appears asking you forconfirmation, click "Allow".

6) The "SOFTWARE LICENSE" window will appear. Make surethat you understand the contents of the software license, andthen click the "Yes" button.

Note: You can show the "SOFTWARE LICENSE" in a differentlanguage by selecting the desired language from thelanguage menu. To install the software in the selectedlanguage, continue the installation with that languageselected.

7) Read the "Readme First" in the "Welcome" window and thenclick the "Next" button.

Note: To set the IP address of the machine, follow the stepsbelow. If the machine is already connected to thenetwork and its IP address has been set, go to "LPR(TCP/IP) direct printing" (p.5-7).

Set the IP Address

This setting is only required once when using the machine on a net-work.

8) Click the "Set the IP Address" button.

9) The printer or printers connected to the network will bedetected.

Click the printer to be configured (the machine) and click the"Next" button.

Note:

• The "Ethernet Address" is indicated on the left side of themachine near the LAN connector.

• If the machine can not be recognized, enter the EthernetAddress and click the "Initialize" button to initialize the IPaddress. Follow the on-screen instructions to click the "OK"button and then the "Search" button. If the machine is still notrecognized, disable your computer’s firewall and then repeatthe installation from the beginning.

(AL-2030/2040CS) (AL-2050CS)


10) Enter the IP address, subnet mask, and default gateway.

The settings in the above window are examples.

Be sure to ask your network administrator for the correct IPaddress, subnet mask, and default gateway to be entered.

Note: When "Get IP Address Automatically" is selected, the IPaddress may at times change automatically. This willprevent printing. In this event, select "Assign IP Address"and enter the IP address.

11) Click the "Next" button.

12) Click the "Yes" button in the confirmation dialog box thatappears.

Go to "LPR (TCP/IP) direct printing" step 11).

LPR (TCP/IP) direct printing

After step 1) - 7) on page 5-6.


If you have not set the IP Address, click the "Set the IPAddress" button first and go to step 8).

9) Read the message in the "Welcome" window and then click the"Next" button.

10) Select "LPR Direct Print" and click the "Next" button.

11) The printer or printers connected to the network will bedetected.

Click the printer to be configured (the machine) and click the"Next" button.

Note: If the machine’s IP address cannot be found, make surethe machine is powered on, make sure the network cableis connected correctly, and then click the "Search"button.

12) In the window for setting the destination print port name, makesure that ":lp" appears at the end of the IP address and click the"Next" button.

Note: Any name can be entered in "Printer Port Name"(maximum of 38 characters).

13) A window appears to let you check your entries. Make sure thatthe entries are correct and then click the "Finish" button.

If any of the entries are incorrect, click the "Back" button toreturn to the appropriate window and correct the entry.

14) Select the port you want to use with the machine, and click the"Next" button.

15) Select whether or not you wish the printer to be your defaultprinter and click the "Next" button.


Caution:



16) When "The installation of the SHARP software is complete."appears, click the "OK" button.

17) When the "Finish" screen appears, click the "Close" button.




(4) Using the machine as a shared printer (AL-2030)If the machine will be used as a shared printer on a network, followthese steps to install the printer driver in the client computer.

Note: To configure the appropriate settings in the print server, seethe operation manual or help file of your operating system.

1) Perform steps 2) through 6) in "Using the machine with a USBconnection" (p.5-4).

2) Click the "Custom" button.



4) Select "Connected via the network" and click the "Next" button.

5) Click the "Add Network Port" button.

6) Select the network printer that is shared and click the "OK" but-ton.

Ask your network administrator for the server name and printername of the machine on the network.

7) In the printer port selection window, verify the network printerthat is shared and whether the machine is to be used as thedefault printer, make the selections and click the "Next" button.


Caution: If you are running Windows 2000/XP and a warningmessage appears regarding the Windows logo test ordigital signature, be sure to click "Continue Anyway"or "Yes".

8) You will return to the window of step 3). Click the "Close" button.



(5) Sharing the printer using windows networking (AL-2040CS/2050CS)

If the machine will be used as a shared printer on a network, followthese steps to install the printer driver in the client computer.

Note: To configure the appropriate settings in the print server, seethe operation manual or help file of your operating system.

1) Perform steps 3) through 7) in "Using the machine as a networkprinter" (p.5-6).


3) Select "Shared Printer" and click the "Next" button.


4) For the port to be used, select the machine set as a sharedprinter, and click the "Next" button.

You can also click the "Add Network Port" button and select theprinter to be shared (the machine) by browsing the network inthe window that appears.

Note: If the shared printer does not appear in the list, check thesettings in the printer server.

5) Follow the on-screen instructions.

6) When the "Finish" screen appears, click the "Close" button.



C. Setting up Button Manager (AL-2040CS/2050CS only)

Button Manager is a software program that works with the scannerdriver to enable scanning from the machine.

To scan using the machine, Button Manager must be linked with thescan menu on the machine. Follow the steps below to link ButtonManager to scanner events.

(1) Windows XP/Vista1) Click the "start" button, click "Control Panel", click "Printers and

Other Hardware", and then click "Scanners and Cameras".

In Windows Vista, click the "Start" button, select "Control Panel"and click "Hardware and Sound", and then click "Scanners andCameras".

2) Click the "SHARP AL-XXXX" icon and select "Properties" fromthe "File" menu.

In Windows Vista, select "Properties" from the "Organize"menu.

3) In the "Properties" screen, click the "Events" tab.

4) Select "SC1:" from the "Select an event" pull-down menu.

5) Select "Start this program" and then select "Sharp Button Man-ager O" from the pull-down menu.

6) Click the "Apply" button.

7) Repeat Steps 4) through 6) to link Button Manager to "SC2:"through "SC6:".

Select "SC2:" from the "Select an event" pull-down menu.Select "Start this program", select "Sharp Button Manager O"from the pull-down menu, and then click the "Apply" button. Dothe same for each ScanMenu through "SC6:".

When the settings have been completed, click the "OK" buttonto close the screen.

Button Manager is now linked to the scan menu (1 through 6).

The scan settings for each of scan menu 1 through 6 can bechanged with the setting window of Button Manager.

For the factory default settings of the scan menu and the proce-dures for configuring Button Manager settings, see "ButtonManager Settings" in the Online Manual.

(2) Windows 98/Me/20001) Click the "Start" button, select "Settings", and then click "Con-

trol Panel".

2) Double-click the "Scanners and Cameras" icon.

Note: If the "Scanners and Cameras" icon does not appear inWindows Me, click "view all Control Panel options".

3) Select "SHARP AL-XXXX" and click the "Properties" button.

In Windows Me, right click "SHARP AL-XXXX" and click "Prop-erties" in the pop-up menu.

4) In the "Properties" screen, click the "Events" tab.

5) Select "SC1:" from the "Scanner events" pull-down menu.


6) Select "Sharp Button Manager O" in "Send to this application".

Note: If other applications are shown, deselect the checkboxesfor the other applications and leave only the ButtonManager checkbox selected.

7) Click the "Apply" button.

8) Repeat Steps 5) through 7) to link Button Manager to "SC2:"through "SC6:".

Select "SC2:" from the "Scanner events" pull-down menu.Select "Sharp Button Manager O" in "Send to this application"and click the "Apply" button.

Do the same for each ScanMenu through "SC6:".

When the settings have been completed, click the "OK" buttonto close the screen.

Button Manager is now linked to the scan menu (1 through 6).

The scan settings for each of scan menus 1 through 6 can bechanged with the setting window of Button Manager.

For the factory default settings of the scan menu and the proce-dures for configuring Button Manager settings, see "ButtonManager Settings" in the Online Manual.

10. InterfaceA. USB

ConnectorType-B connector

CableShielded twisted pair cable

(2 m (6 feet) Max.: high-speed transmission equivalent)

Pin configurationThe pin numbers and signal names are listed in the following table.

B. RJ45RJ-45 connector pin arrangement

11. MovingMoving instructionsWhen moving the unit, follow the procedure below.

Note: When moving this unit, be sure to remove the TD cartridge inadvance.

1) Turn the power switch off and remove the power cord from theoutlet.

2) Open the side cover and front cover, in that order. Remove theTD cartridge and close the front cover and side cover, in thatorder.

To open and close the side cover and front cover, and to removethe TD cartridge.

3) Raise the handle of the paper tray and pull the paper tray outuntil it stops.

4) Push the center of the pressure plate down until it locks in placeand lock the plate using the pressure plate lock which has beenstored in the front of the paper tray.

5) Push the paper tray back into the unit.

6) Lock the scan head locking switch.

Note: When shipping the unit, the scan head locking switch mustbe locked to prevent shipping damage.

7) Close the multi-bypass tray and the paper output tray extension,and attach the packing materials and tape which were removedduring installation of the unit.

8) Pack the unit into the carton.

12. Scanner moisture-proof kitIf the machine is installed in a highly humid environment, you canalleviate dew condensation inside the scanner by installing thescanner moisture-proof kit described below.

A. ComponentsScanner moisture-proof kit (DKIT-0016QSZZ)

B. Precautions at installationClean the position where each cushion/mylar is attached withindustrial alcohol before the work.

Pin No. Signal name1 +5V2 -DATA3 +DATA4 GND

12

3 4

Pin No. Signal name LAN adapter RJ-45 connector1 TD+ Send output +

2 TD– Send output -

3 RD+ Receive input +

6 RD– Receive input -

4, 5, 7, 8 Not used. Not used.

Name Part code Qty

1 Scanner condensation prevention mylar

PSHEZ0493QSZZ 3

2 Optical right hole mylar B PSHEZ0469QSZZ 2

3 Scanner motor metal plate cushion

PMLT-0106QSZZ 2

4 Scanner upper surface cushion PMLT-0105QSZZ 1

5 Scanner motor lower mylar PSHEP0600QSZZ 16 Scanner UPG mylar J3 PSHEP0599QSZZ 1

7 Fan housing cushion PMLT-0108QSZ1 1

1 8


C. Attachment methodTurn the main switch to the "OFF" position and remove the powerplug from the outlet.

1) Detach the RSPF.

Detach the RSPF from the copier and softly place it on top ofthe original table as shown below.

2) Remove the rear cabinet.

<1> Unscrew the screw and remove the rear cabinetshielding plate. (Save the screw.)

<2> Unscrew three screws and remove the rear cabinet. (Savethe screws.)

<3> Disconnect the connector of the RSPF, and remove theRSPF from the machine.

3) Remove the rear cover for the document glass.

<1> Remove the two screws and then remove the right glassholder.

<2> Slide the rear cover for the document glass to remove it.

<3> Remove the table glass.

4) Attach the Scanner condensation prevention mylar at the 3positions on the rear side of the main unit as described below.

Note: The hole should be covered with the mylar.

Align the edge of the mylar to the R part (the yellow line in thediagram below) so that the hole of the metal plate is covered asmuch as possible.

Align the edge of the mylar to the R part (the yellow line in thediagram below) so that the hole of the metal plate is covered asmuch as possible.

Attach along the edge of the projection (the yellow line in thediagram below).

1

2

1

23


5) Attach the Optical right hole mylar B at the 2 positions shown inthe diagrams below which are at the top of the rear side of themain unit.

Note: The holes should be covered with the mylar.

Attach along the edge of the cushion (the yellow line in the dia-gram below).

Align with the inside line of the bent part (the yellow line in thediagram below).

Align with the raised part (the yellow line in the diagram below).

Match the center of the mylar (in the horizontal direction) to thecenter of the raised part.

6) Attach the Scanner motor metal plate cushion at 1 position onthe attachment plate of the motor on the rear side of the mainunit.

Note: The hole on the top of the motor unit should be coveredwith the mylar.

Align the edge of the metal plate and the edge of the cushion(the yellow line in the diagram below).

7) Attach the Scanner upper surface cushion on the top and therear side at the rear side of the main unit.

Align the cushion with the side of the raised part (the yellow linein the diagram below).

Bend the part which is sticking out to the rear side of the scan-ner and attach to the surface.

Press the cushion at the steps shown in the diagram so thatthere will be no gap.

Press the cushion to make sure all the holes are covered.

Stick the excessive part on the side.

Stick the excessive part on the side.

Press and attach the cushion aligning it to the metal plate so

that there will be no gap between them.

20mm - 25mm

Do not cover this hole. Align the edge of the cushion with

the edge of the metal plate.


8) Bend the edge of the Scanner motor lower mylar and sticktogether.

9) Attach the Scanner motor lower mylar at 1 position under themotor attachment plate on the rear side of the main unit.

Note: The mylar should cover the hole under the motor unit.

Attach matching the hole (the yellow mark in the diagram) andalong with the side edge (the yellow arrow in the diagram).

Disconnect the motor harness from the connector and take offthe snap band from the hole.

Press the mylar with a sharp-pointed stick or something so thatit is stuck correctly.

10) Attach the Scanner motor metal plate cushion covering the bot-tom part of the Scanner motor lower mylar.

Note: The hole under the motor unit should be covered.

Attach the cushion to cover the gap between the mylar and themetal plate (the yellow mark).

Press the cushion with a sharp-pointed stick or something to fillthe gap between the mylar and the metal plate.

11) Attach the motor connector and the snap band to the originalposition.

Stick together. Stick together.

Stick the lower part of the cushion to the mylar, too.


12) Attach the Scanner UPG mylar J3 to cover the hole on the rightside of inside of the scanner.

Note: The mylar should cover the hole shown by the arrow inthe diagram.

Attach along with the bent part of the metal plate and align theedge of the mylar with the line shown in the diagram (the yellowline in the diagram).

13) Attach the Fan housing cushion to the cooling fan at the posi-tion shown in the diagram below.

Cover the top and the right side of the fan housing when yousee the fan housing from the backside of the machine.

Note: Please make sure the double-sided tape is not exposedwhere the cushion is sticking out from the edge of the fanhousing.

Attach the cushion leaving 3 - 7mm from the edge so that thegap between the Fan housing cushion and the filter of the rearcabinet is filled for sure.

14) Attach the parts removed in the items 1), 2), and 3).

A

View from

the arrow A

Back side

Attach the cushion leaving 3 - 7mm

from the edge.

Reference position

3 - 7mm


[6] COPY PROCESS

1. Functional diagram

(Basic operation cycle)

(20 microns thick)

Aluminum drum

Pigment layer (0.2to 0.3 microns thick)

An OPC drum is used for the photoconductor.(Structure of the OPC drum layers)

OPC layer

Main charger

Laser beam

MG roller

Cleaning blade

Drum

Transfer unit

Resist roller

ExposureMain high voltage unit

Saw tooth Charge

DrumCleaning

Cleaning blade

Waste toner box

Paper release Fusing Separation

Heat roller

Heater lamp

Transfer

Transfer charger

Transfer highvoltage unit

Developing

Toner

Developer

Print process

Paper transport route

Semiconductor laser

Manual feed

PS roller

Focus correction lens

Electrode

Synchronizationwith drum

Cassettepaper feed

To facedown tray

AL-2030/2040CS/2050CS COPY PROCESS 6 - 1

2. Outline of print processThis printer is a non-impact printer that uses a semiconductorlaser and electrostatic print process. This printer uses an OPC(Organic Photo Conductor) for its photoconductive material.

First, voltage from the main corona unit charges the drum surfaceand a latent image is formed on the drum surface using a laserbeam. This latent image forms a visible image on the drum surfacewhen toner is applied. The toner image is then transferred onto theprint paper by the transfer corona and fused on the print paper inthe fusing section with a combination of heat and pressure.

Step-1: Charge

Step-2: Exposure

∗ Latent image is formed on the drum.

Step-3: DevelopingLatent image formed on the drum is then changed intovisible image with toner.

Step-4: TransferThe visible image (toner image) on the drum is transferredonto the print paper.

Step-5: CleaningResidual toner on the drum surface is removed and col-lected by the cleaning blade.

Step-6: Optical dischargeResidual charge on the drum surface is removed, bysemiconductor laser beam.

3. Actual print processStep-1: DC charge

A uniform negative charge is applied over the OPC drum surfaceby the main charging unit. Stable potential is maintained by meansof the Scorotron charger.

Positive charges are generated in the aluminum layer.

Step-2: Exposure (laser beam, lens)

A Laser beam is generated from the semiconductor laser and con-trolled by the print pattern signal. The laser writes onto the OPCdrum surface through the polygon mirrors and lens. The resis-tance of the OPC layer decreases for an area exposed by the laserbeam (corresponding to the print pattern signal). The beam neu-tralizes the negative charge. An electrostatic latent image isformed on the drum surface.

AboutDC5.5KV

( 580V/ 400V)

OPC layerPigmentlayerAluminumdrum

OPC layerPigmentlayerAluminumlayer

Drum surface chargeafter the exposure

Non-image area Image area

Semiconductor laser

Exposure(semiconductor laser)


Step-3: Developing (DC bias)

A bias potential is applied to the MG roller in the two componentmagnetic brush developing method, and the toner is charged nega-tive through friction with the carrier.

Non-image area of the drum surface charged with negative poten-tial repel the toner, whereas the laser exposed portions where nonegative charges exist, attract the toner. As a result, a visibleimage appears on the drum surface.

Toner is attracted over the shadowed area because of the develop-ing bias.

Step-4: Transfer

The visible image on the drum surface is transferred onto the printpaper by applying a positive charge from the transfer corona to thebackside of the print paper.

Step-5: Separation

Since the print paper is charged positively by the transfer corona, itis discharged by the separation corona. The separation corona isconnected to ground.

Step-6: Cleaning

Toner remaining on the drum is removed and collected by thecleaning blade. It is transported to the waste toner collecting sec-tion in the cleaning unit by the waste toner transport roller.

S

N

N

:Carrier (Magnetized particle):Toner (Charge negative by friction)(N) (S) Permanent magnet

(provided in three locations)

MG roller

DC400V 8V

About DC 5.2kV


Step-7: Optical discharge (Semiconductor laser)

Before the drum rotation is stopped, the semiconductor laser isradiated onto the drum to reduce the electrical resistance in theOPC layer and eliminate residual charge, providing a uniform stateto the drum surface for the next page to be printed.

When the electrical resistance is reduced, positive charges on thealuminum layer are moved and neutralized with negative chargeson the OPC layer.

Charge by the Scorotron charger

Function

The Scorotron charger functions to maintain uniform surfacepotential on the drum at all times, It control the surface potentialregardless of the charge characteristics of the photoconductor.

Basic function

A screen grid is placed between the saw tooth and the photocon-ductor. A stable voltage is added to the screen grid to maintain thecorona current on the photoconductor.

As the photoconductor is charged by the saw tooth from the maincorona unit, the surface potential increases. This increases thecurrent flowing through the screen grid. When the photoconductorpotential nears the grid potential, the current turns to flow to thegrid so that the photoconductor potential can be maintained at astable level.

Process controlling

Function

The print pattern signal is converted into an invisible image by thesemiconductor laser using negative to positive (reversible) devel-oping method. Therefore, if the developing bias is added beforethe drum is charged, toner is attracted onto the drum. If the devel-oping bias is not added when the drum is charged, the carrier isattracted to the drum because of the strong electrostatic force ofthe drum.

To avoid this, the process is controlled by adjusting the drumpotential and the grid potential of the Scorotron charger.

Basic function

Voltage added to the screen grid can be selected, high and low. Tomake it easily understood, the figure below shows voltage transi-tion at the developer unit.

Start1) Because the grid potential is at a low level, the drum potential

is at about -400V. (Carrier may not be attracted though the car-rier is pulled towards the drum by the electrostatic force of -400V.

2) Developing bias (-400V) is applied when the photoconductorpotential is switched from LOW to HIGH.

3) Once developing bias (-400V) is applied and the photo conduc-tor potential rises to HIGH, toner will not be attracted to thedrum.

StopThe reverse sequence takes place.

Retaining developing bias at an abnormal occurrence

Function

The developing bias will be lost if the power supply was removedduring print process. In this event, the drum potential slightlyabates and the carrier makes deposits on the drum because ofstrong static power. To prevent this, the machine incorporates afunction to retain the developing bias for a certain period anddecrease the voltage gradually against possible power loss.

Basic function

Normally, the developing bias voltage is retained for a certain timebefore the drum comes to a complete stop if the machine shouldstop before completing the normal print cycle. The developing biascan be added before resuming the operation after an abnormalinterruption. Therefore, carrier will not make a deposit on the drumsurface.

Semiconductor laser

0START STOP

Print potential

Toner attractpotential

2)

3)

1) Low

4) High Drum potential

Developing bias

Time


[7] OPERATIONAL DESCRIPTIONS

1. Outline of operationThe outline of operation is described referring to the basic configuration.

(Basic configuration)

(Outline of copy operation)Setting conditions

1) Set copy conditions such as the copy quantity and the copydensity with the operation section, and press the Start key. Theinformation on copy conditions is sent to the MCU.

Image scanning

2) When the Start key is pressed, the scanner section starts scan-ning of images. The light from the copy lamp is reflected by the document andpassed through the lens to the CCD.

Photo signal/Electric signal conversion

3) The image is converted into electrical signals by the CCD circuitand passed to the MCU.

Image process

4) The document image signal sent from the CCD circuit is pro-cessed under the revised conditions and sent to the LSU (laserunit) as print data.

Electric signal/Photo signal (laser beam) conversion

5) The LSU emits laser beams according to the print data.(Electrical signals are converted into photo signals.)

6) The laser beams are radiated through the polygon mirror andvarious lenses to the OPC drum.

Printing

7) Electrostatic latent images are formed on the OPC drumaccording to the laser beams, and the latent images are devel-oped to be visible images (toner images).

8) Meanwhile the paper is fed to the image transfer section in syn-chronization with the image lead edge.

9) After the transfer of toner images onto the paper, the tonerimages are fused to the paper by the fusing section. The copiedpaper is discharged onto the exit tray.

(Outline of printer operation)The print data sent from the PC are passed through the NIC PWB(in case of network connection) and the MCU to the LSU. The pro-cedures after that are the same as above 5) and later.

(Outline of scanner operation)The scan data are passed through the MCU to the PC accordingto the conditions requested by the operations with the operationpanel.

Operationsection

Scanner section

CCD

MCU (Main control/image process section)

USB PC

Laser beamPaper exit

Fusing section

Paper transport section

Manual paperfeed section

Cassette paperfeed section

Printer section

LSU (Laser unit)Laser diode, Polygon mirror lens

Process section

NIC PWB(AL-2040CS/

2050CS)

Network(print only) PC

AL-2030/2040CS/2050CS OPERATIONAL DESCRIPTIONS 7 - 1

2. Scanner sectionA. Scanner unitThe scanner unit in the digital copier scans images.

It is composed of the optical unit and the drive unit. The optical unitperforms scanning in the main scan direction with the light receivingelements (color CCD). The drive unit performs scanning in the subscanning direction by moving the optical unit.

B. Optical systemTwo white lamps are used as the light source.

Light radiated from the light source is applied to the document onthe document table. The reflected light from the document isreflected 4 times by No. 1 - No. 3 mirrors and passed through thereduction lens to form images on the light-receiving surface of 3-lineCCD.

The light-receiving surface of the color CCD is provided with 3 linescanning sections for RGB. Separate images scanned in each colorsection are overlapped to complete color scanning. (When PCscanning)

The resolution is 600dpi.

When copying, only the green component is used to print with theprinter.

The color component for printing can be switched to red or blue bythe service simulation.

(Spectrum characteristics of the lamp)

(Spectrum characteristics of the color CCD)

(Optical unit)

C. Drive systemThe drive system is composed of the scanner motor, the pulleygear, the idle pulley, the idle gear, the belt 473, the belt 190, and theshaft.

The motor rotation is converted into reciprocated movements of thebelt 473 through the idle gear, the pulley gear, the belt 190, and theidle pulley to drive the optical unit.

100

75

5045.4

100.0

50.2

25

380 480 580 680 780

Wavelength [nm]

Sen

sitiv

ity

1 Table glass 2 Optical unit 3 Lens4 Mirror 1 5 Mirror 2 6 Mirror 37 CCD PWB 8 Lamp 9 Reflector10 Original

Spectral sensitivity characteristics (Standard characteristics)

Rela

tive

se

nsitiv

ity

Wavelength [nm]

89 98101

7

53 4 2

6

7 9

3 4 6 2 8 5

1

3

1 Scanner motor 2 Pulley gear 3 Idle pulley4 Belt 473 5 Belt 190 6 Optical unit7 Shaft 8 Idle gear 9 Table glass


3. Laser unitThe image data sent from the MCU (image process circuit) is sentto the LSU (laser unit), where it is converted into laser beams.

A. Basic structureThe LSU unit is the writing section of the digital optical system.

The semiconductor laser is used as the light source, and imagesare formed on the OPC drum by the polygon mirror and fθ lens, etc.

The laser beams are passed through the collimator lens, the cylin-drical lens, the polygon mirror, the fθ lens, and the mirror to formimages on the OPC drum in the main scanning direction. The laseremitting PWB is provided with the APC (auto power control) in orderto eliminate fluctuations in the laser power. The BD PWB works formeasurement of the laser writing start point.

Makes the laser scanning speeds at both ends of the drum same aseach other.

B. Laser beam path

C. CompositionEffective scanning width: 216mm (max.)

Resolution: 600dpi

Beam diameter: 75um in the main scanning direction, 80um in thesub scanning direction

Image surface power: 0.18 ± 0.01mW (Laser wavelength 770 -795nm)

Polygon motor section: Brushless motor 20.787rpmNo. of mirror surfaces: 5 surfaces

4. Fuser section

No Component Function1 Semiconductor laser Generates laser beams.2 Collimator lens Converges laser beams in parallel.3 Cylinder lens Takes the focus.4 Polygon mirror,

polygon motorReflects laser beams at a constant rpm.

5 BD (Lens, PWB) Detects start timing of laser scanning.

6 fθ lens Converges laser beams at a spot on the drum.Makes the laser scanning speeds at both ends of the drum same as each other. (Refer to the figure below.)

2

3

3

6

4 1

5

6

a ≠ b ≠ ca b c

d = e = fd e f

fθ LENS


A. General descriptionGeneral block diagram (cross section)

Top view

(1) Heat rollerA Teflon roller is used for the heat roller and a silicone rubber rolleris used for the lower heat roller for better toner fusing performanceand paper separation.

(2) Separator pawlThree separator pawls are used on the upper heat roller. The sep-arator pawls are Teflon coated to reduce friction with the roller andprevent a smear on the paper caused by the separator pawl.

(3) Thermal control1) The heater lamp, thermistor, main PWB, DC power supply

PWB, and triac within the power supply unit are used to controlthe temperature in the fuser unit.To prevent against abnormally high temperature in the fuserunit, a thermal breaker and thermal fuse are used for safety pur-poses.

2) The surface temperature of the upper heat roller is set to 160 -200°C. The surface temperature during the power save mode isset to 100°C.

3) The self-check function comes active when one of the followingmalfunctions occurs, and an "H" is displayed on the multicopywindow.

a. When the heat roller surface temperature rises above 240°C.

b. When the heat roller surface temperature drops below 100°Cduring the copy cycle.

c. Open thermistor

d. Open thermal fuse

e. When the heat roller temperature does not reach 190°C within27 second after supplying the power.

(4) Fusing resistorThis model is provided with a fusing resistor in the fusing sectionto improve transfer efficiency.

Since the upper heat roller is conductive, when using copy paperthat contains moisture and the distance between the transfer unitand the fusing unit is short, the transfer current may find a path toground via the copy paper, the upper heat roller and the discharg-ing brush.

5. Paper feed section and paper transport section

A. Paper transport path and general operations

Paper feed is made in two ways; the tray paper feed and the man-ual paper feed. The tray is of universal-type, and has the capacityof 250 sheets.

The front loading system allows you to install or remove the trayfrom the front cabinet.

The general descriptions on the tray paper feed and the manualpaper feed operation are given below.

Separator pawl

Separator pawl

PPD2

Thermal fuse

Thermistor

Heat roller

Paper guide

Pressure roller

Heat rollerThermistor

Thermal fuse

Heater lamp

Separator pawl

Safety device(thermal breaker, thermalfuse)

Triac (in thepower supply unit)

Heated by the heater lamp. (950W)

The surface temperatureof the upper heat roller issensed by the thermistor.

Level of the thermistor iscontrolled by the main PWB.

With the signal from themain PWB, the triac iscontrolled on and off.(power supply PWB)

1 Scanner unit 8 Drum

2 Copy lamp 9 Transfer unit3 LSU (Laser unit) 10 Pickup roller

4 Paper exit roller 11 Manual paper feed tray

5 Main charger 12 Manual paper feed roller

6 Heat roller 13 PS roller unit

7 Pressure roller 14 Paper feed roller

1

54 3

7

6

89

11121314

10

2


(1) Cassette paper feed operation1) The figure below shows the positions of the pick-up roller, the

paper feed clutch sleeve, and the paper feed latch in the initialstate without pressing the Start key after lighting the readylamp.The paper feed latch is in contact with the projection of theclutch sleeve.

2) When the Start key is pressed, the main drive motor startsrotating to drive each drive gear.The pick-up drive gear also is driven at that time. Since, how-ever, the paper feed latch is in contact with the projection of theclutch sleeve, rotation of the drive gear is not transmitted to thepick-up roller, which does not rotate therefore.

3) After about 0.1 sec from when the main motor start rotating, thetray paper feed solenoid (PFS) turns on for a moment.This disengages the paper feed latch from the projection of theclutch sleeve, transmitting rotation of the pick-up drive gear tothe paper feed roller shaft, rotating the pick-up roller to feed thepaper.

4) After more than half rotation of the pick-up roller, the paper feedlatch is brought in contact with a notch on the clutch sleeve,stopping rotation of the pick-up roller.

5) At this time, the paper is fed passed the paper entry detectionswitch (PPD1), and detected by it. After about 0.15 sec fromdetection of paper by PPD1, the tray paper feed solenoid (PFS)turns on so that the clutch sleeve projection comes into contactwith the paper feed latch to stop the pick-up roller. Then thepick-up roller rotates for about 0.15 sec so that the lead edge ofthe paper is evenly pressed on the resist roller, preventingagainst skew feeding.

6) To release the resist roller, the tray paper feed solenoid and theresist solenoid are turned on by the paper start signal to disen-gage the resist start latch from the clutch sleeve, transmittingrotation of the resist drive gear to the resist roller shaft. Thus thepaper is transported by the resist roller.

7) After the resist roller starts rotating, the paper is passed throughthe pre-transfer guide to the transfer section. Images are trans-ferred on the paper, which is separated from the OPC drum bythe drum curve and the separation section.

8) The paper separated from the drum is passed through the fus-ing paper guide, the heat roller (fusing section), POD (paper outdetector) to the copy tray.

OFF

PFS

OFF

RRS

OFF

PFS

OFF

RRS

ON

PFS

OFF

RRS

OFF

PFS

ON

RRS


(2) Manual multi paper feed operation1) Before paper feed operation, the manual paper feed solenoid

(MPFS) is turned OFF as shown in the figure below.

2) When the Start key is pressed, the manual paper feed solenoid(MPFS) turns on to disengage the manual paper feed latch.A from the manual paper feed clutch sleeve A, rotating the man-ual paper feed roller and the manual take-up roller. At the sametime, the manual paper feed stopper opens and the manualtake-up roller is pressed to the surface of the paper to startpaper feeding.

3) When pawl C of the manual paper feed clutch sleeve isengaged with the manual feed latch, the manual feed stopperfalls and the manual take-up roller rises. At that time, the man-ual paper feed roller is rotating.

4) The lead edge of the transported paper is pressed on the resistroller by the transport roller. Then the paper is stopped tempo-rarily to allow synchronization with the lead edge of the imageon the OPC drum.From this point, the operation is the same as the paper feedoperation from the tray. (Refer to 7-5 - 8.)

5) The solenoid turns off to close the gate and return to the initialstate.

OFMPFS

F

C A

ON

MPFS

A

C

ONMPFS

A

C

OFMPFS

F

AC


(3) Conditions of occurrence of paper misfeed

a. When the power is turned on:PPD or POD is ON when the power is turned on.

b. Copy operation

6. Process unit new drum detection mechanism

1) When the power is turned on, the detection gear 38T is rotatedin the arrow direction by the detection gear 20T to push themicro-switch (process detection switch) installed to the machinesensor cover, making a judgement as a new drum.

2) When the detection gear 38T turns one rotation, there is nogear any more and it stops.

The latch section of the 38T gear is latched and fixed with theprojection of the process cover.

7. SPF/RSPF sectionA. OutlineThe SPF (Single Path Feeder) is installed to the AL-2030/2040CSas a standard provision.

The RSPF (Reverse Single Path Feeder) is installed to the AL-2050CS as a standard provision.

It automatically copies up to 50 sheets of documents of a samesize. (Only one set of copies)

a PPD1 jam PPD1 does not turn off within 4 sec after turning on the resist roller.

b PPD2 jam PPD2 is off immediately after turning on the resist roller.

PPD2 does not turn off within 1.2 sec after turning off the resist roller.

c POD jam POD does not turn on within 2.9 sec after turning on the resist roller.

POD does not turn off within 1.5 sec - 2.7 sec after turning off PPD2.

Gear 20T

Process detection switch

Gear 38T

Gear notch

Gear pawl

Projection

Gear notch

Gear pawl

Projection


B. Document transport path and basic composition

AL-2030/2040CS

AL-2050CS

C. Operational descriptions

AL-2030/2040CS

SPF JAM generation condition

1) When SPPD is ON (document remaining) in initializing

2) When SPPD is not turned ON within about 1.5 sec (at 100%copy) after starting the document feed operation.

3) When SPPD is not turned OFF within about 4.7 sec (at 100%copy) after turning on SPPD.

4) When the OC cover is opened during document transport (dur-ing SPF motor rotation) (The SPF motor is stopped during doc-ument transport, but the OC cover open error occurs instead ofthe SPF JAM.)

1 Pickup roller 2 Sheet of document for paper feed3 Set detection ACT 4 Document feed roller5 Separation sheet 6 Paper entry sensor7 PS roller D 8 Transport follower roller9 Paper exit roller 10 Paper exit follower roller11 Document tray

1 Pickup roller 2 Separation roller3 Paper empty sensor 4 Upper transport roller5 Paper sensor 6 PS roller7 Lower transport roller 8 Reverse self-weight gate9 Paper exit sensor 10 Paper exit roller

1119 3 4

5

210 6 7

8

1 2 4 5

6810 7

3

9

SPID ON

PSW ON

MRMT rotation

MM rotation

CPFS ON

SPFM rotation

Document set

Document set sensor

Document feed unit lamp ON

PPD ON

RRC ON SPPD ON

POD ON

Copy start

The scanner is shiftedto the exposure position.

(Copier side)

Main motor rotation

Paper feed

Synchronization

(Transfer)

(Fusing) (Document exit)

Paper transport(Exposure)

In the zooming mode, the magnification ratio in the sub scanning direction (paper transport direction) is adjustedby changing the document transport speed.

(Paper exit)

SPF motor rotation

Document transport sensor

Document transport

(SPF side)

PSW

MRMT

SPF M

CL

SPPD260ms 182ms

SCANST

MAIN M

CPFS1

RRS

PPD1

PPD2

POD


AL-2050CS

RSPF JAM generation condition

1) The SPPD is ON when turning ON the power.

2) The SPPD does not turn ON for 4.0sec from starting documentfeed. (in 100% copy)

3) The SPPD does not turn OFF for 4.7sec after detecting turningON of the SPPD. (100% copy)

4) The RSPF cover or the OC cover is opened during documenttransportation.

5) The SRJD is ON when the power is turned ON.

6) The SRJD is not turned ON for 2.4sec from release of PS inpaper feed from the document set position. (100% copy)

7) The SRJD is not turned OFF for 1.6sec from completion of doc-ument scan in the case of complete document exit. (100%copy)

D. SPF/RSPF open/close detection (book document detection)

SPF/RSPF open/close detection (book document) detection is per-formed by detecting the interval between the reference lines on thewhite Mylar attached to the paper exit guide (document scanningsection) by the scanner (CCD) and detecting the varied quantity.

Note: When replacing the carriage unit, be sure to execute SIM41-06.If SIM41-06 is not executed, the carriage unit may not readthe reference line on the white Mylar, preventing the docu-ment from being fed.

8. D-D (Duplex to Duplex) mode paper/document transport (Duplex model) (AL-2050CS only)

A. Initial stateSet duplex documents on the document tray.

Set paper on the cassette. (In the duplex mode, the manual feedtray cannot be selected.)

B. Front copyDocument transport:

The document feed roller feeds the document from the paper feedroller to the PS roller.

• The document is exposed in the exposure section, and trans-ported to the document exit section by the lower transport rollerand the paper exit roller.

• The document is transported to the paper exit tray. (However, it isnot discharged completely.)

• The document is stopped once, and then switchback operation isperformed. (To the back copy)

Paper transport:

The paper is passed through the paper feed roller and the PS roller,and the images on the front surface are transferred.

• The paper is passed through the fusing section and the lowerside of the gate section to the paper exit tray side. (However, it isnot discharged completely.)

• The paper is stopped once, and switchback operation is per-formed. (To the back copy)

PSW

MRMT

SPF M

CLSPUSSPPD

SCANST

SRVC

SRJD

MAIN M

CPFS1RRSPPD1

PPD2

POD

1200msec560msec

BA

B

AA - B = Varied quantity of pixels

(pixel)

(Floating)

(White Mylar)

(CCD)

Reference line Reference line


C. Back copyDocument transport:

By switchback operation, the document is sent through the uppertransport roller and the PS roller to the exposure section, where theback surface of the document is exposed.

• The document is sent to the document exit section by the lowertransport roller and the paper exit roller.

• The document is sent to the intermediate tray. (However, it is notdischarged completely.)

• The document is stopped once, and switchback operation is per-formed.

• The document is sent through the upper transport roller and thePS roller and the exposure section (without being exposed) to thedocument exit section.

• The document is discharged to the document exit tray.

Paper transport:

Switchback operation is performed.

• The paper is sent through the upper side of the gate section andthe duplex transport section and the PS roller, and the images onthe back surface are transferred.

• The paper is sent through the fusing section and discharged tothe paper exit tray.

Rotation copy mode:

The front and the back are in upside down each other.

Copy mode without rotation:

The front and the back are not in upside down.

9. Shifter (AL-2050CS only)

Shift width: 2.5cm

The offset function by the shifter is turned ON/OFF by the user pro-gram.

According to the setting, offset operation is performed for every job.(Default: ON)


[8] DISASSEMBLY AND ASSEMBLY

The disassembly and assembly procedures are described for thefollowing sections:

1. High voltage section

2. Operation panel section

3. Optical section

4. Fusing section

5. Tray paper feed/transport section

6. Manual paper feed section

7. Rear frame section

8 Power section

9. Duplex motor section (AL-2040CS/2050CS only)

10. Reverse roller section (AL-2040CS/2050CS only)

11. RSPF section (AL-2050CS only)

12. SPF section (AL-2030/2040CS only)

13. 2nd cassette section (AL-2040CS/2050CS only)

1. High voltage sectionA. List

B. Disassembly procedure1) Press the side cover open/close button and open the side

cover.

2) Push up the lock pawls (2 positions) of the side cover, andremove the transfer charger.

C. Assembly procedureFor assembly, reverse the disassembly procedure.

D. Charger wire cleaning1) Remove the charger cleaner from the manual paper feed unit.

Before disassembly, be sure to disconnect the power cord for safety.

1. Do not disconnect or connect the connector and the harness while the machine is powered. Especially be careful not to disconnect or connect the harness between the MCU PWB and the LSU (MCU PWB: CN42) during the machine is powered. (If it is disconnected or connected during the machine is powered, the IC inside the LSU will be destroyed.)

2. To disconnect the harness after turning on the power, be sure to turn off the power and wait for at least 10 sec before disconnection. (Note that a voltage still remains immediately after turning off the power.)

No. Part name Ref.1 Transfer charger unit2 Charger wire

1)

2)

2)

1)

1)Transfercharger

Lock pawl rear

Lock pawl front

1)

AL-2030/2040CS/2050CS DISASSEMBLY AND ASSEMBLY 8 - 1

2) Clean the TC front guide and the TC holder with alcohol.

3) Set the charger cleaner to the transfer unit, and move it recipro-cally a few times in the direction of the arrow shown in the figurebelow.

E. Charger wire replacement1) Remove the TC cover and remove the screw.

2) Remove the spring and remove the charger wire.

3) Install a new charger wire by reversing the procedures (1) and(2).At that time, be careful of the following items.

• The rest of the charger wire must be within 1.5mm. Refer to Fig.1

• The spring hook section (charger wire winding section) must bein the range of the projection section.

• Be careful not to twist the charger wire.

2. Operation panel sectionA. List

B. Disassembly procedure1) Open the side door, and Open the front cover.

1)

2)

3)4)

No. Part name Ref.1 Operation panel unit2 Operation PWB

1mm

1.5mm

Fig.1

1)

1)

2)

3)

Charger wire

Protrusion

1)

2)


2) Remove the screws (4 pcs.), the harness, and the operationpanel unit.

3) Remove four screws, and remove the operation cabinet.

4) Remove four screws, and remove the operation PWB.

(AL-2030/2040CS)

(AL-2050CS)

C. Assembly procedureFor assembly, reverse the disassembly procedure

3. Optical sectionA. List

B. Disassembly procedure1) Remove four screws, and remove the rear cabinet and the rear

cabinet cover.

1)

1)

1)

2)

1)

1)

1)1)

1)2)

3)3)

3)

3)3)

3)

3) 3)

4)

NO. Part name Ref.1 Copy lamp unit2 Copy lamp3 Lens unit

1)

3)

2)

2)

5)

5)

5)

5)

4)

1)

1)

2)

2)

1)


2) Remove two screws, and remove the earth wire.

3) Disconnect the connector.

4) Remove the SPF/RSPF unit.

5) Remove five screws. Remove the operation unit, and discon-nect the connector.

6) Remove the right cabinet.

7) Remove the left cabinet.

8) Remove the screw, and remove the rear cover.

9) Remove the table glass.

10) Move the carriage to the position indicated on the figure.

11) Loosen the screw which is fixing the tension plate.

12) Move the tension plate in the arrow direction to release the ten-sion, and remove the belt.

13) Remove the screw, and remove the rod stopper.

14) Remove the rod.

15) Lift the rear side of the carriage, remove the belt and the con-nector, and remove the carriage.

1)

2)

3)

1)

2)

4)

5)

6)

7)

8)

1)

1)

1)

3)

1)

1)

1)

2) 4)

3)

1)2)

3)

1)

2)

4)

3)


C. Assembly procedureCCD core

1) Insert the CCD-MCU harness into the CCD PWB of the car-riage unit.

2) Attach the CCD-MCU harness to the duplex tape on the backsurface of the carriage unit. Clean and remove oil and dirt fromthe attachment surface.

3) Pass the CCD-MCU harness through the square hole in thebase plate.

4) Attach the CCD-MCU harness to the base plate with duplextape.

5) Attach two cable fixing sheets to fix the CCD-MCU harness tothe base plate.

6) Pass the core through the CCD-MCU harness and fix the core.

7) Insert the CCD-MCU harness into the MCU PWB.

4. Fusing sectionA. List

B. Disassembly procedure1) Remove the connectors (3 pcs.) of the rear cabinet.

2) Open the side cover, remove two screws, and remove the fus-ing unit.

3) Cut the binding band, remove the screw, and remove the ther-mistor.

Note: Attach the FCC to the base plate securely with duplex tape to prevent against coming loose.

Note: Attach the FCC to fit with the marking line. Marking line.

No. Part name Ref.1 Thermistor2 PPD2 sensor3 Heater lamp4 Pressure roller5 Heat roller

1)

2)3)

2)

1)

2)

3)Thermistor


4) Remove the screw and remove the U-turn guide.

Pressure roller section disassembly

5) Remove the three screws, remove the fusing cover lower on theright side, and open the heat roller section.

6) Remove the screw and remove the PPD2 sensor.

7) Remove the plate spring on the right and remove the heaterlamp.

8) Remove the spring, and remove the upper separation pawls (3pcs.).

9) Remove the E-ring and remove the reverse gate.

1)

2)

1)

5)

5)

6)

6)

4)3)2)

1)

2)PPD2 sensor

1)

2)

Heater lamp

3)

1)

2)

2)

1)

3)


10) Remove the spring, and remove the lower separation pawls (4pcs.).

11) Remove the pressure release levers on the right and the leftsides.

12) Remove the pressure roller, the pressure bearing, and thespring.

Note: Apply grease to the sections specified with an asterisk (∗).Grease: "JFE552" UKOG-0235FCZZ

Heat roller disassembly

(Continued from procedure (4).)

5) Remove screws, remove the fusing cover, and open the heatroller section.

6) Remove the C-ring and the fusing bearing, and remove the heatroller.

7) Remove the parts from the heat roller.

Note: Apply grease to the sections specified with ∗1.Grease: "JFE552" UKOG-0235FCZZ

8) Remove two screws and remove the thermo unit.

Note: The set temperature of the thermostat differs from that of thecurrent model.

2)

2)

2)

1)

2)

1)

1)

1)

2)

2)

1)

3)

3)

Pressure roller

Temperature

Current model 210°C

AL-2030/2040CS/2050CS 230°C

1)

2)

2)

3)

3)

1)2) 3) Heat roller

3)2)

1)

1

1

1



5. Tray paper feed/transport sectionA. List

B. Disassembly procedure1) Remove the paper holding arm.

Remove the arm holder from the main unit, and remove theholder from the arm. (AL-2050CS only)

2) Remove two screws, and remove the hinge guide R.

3) Disconnect the connector. (2 positions)

4) Remove five screws, and remove the scanner unit.

5) Remove the fan duct.

6) Remove each connector and four screws, and remove the MCUPWB. (The shape of the MCU PWB differs depending on themodel.)

No. Part name Ref.1 PPD1 sensor PWB2 POD sensor PWB3 LSU unit4 Intermediate frame unit5 Paper feed roller

1)

2)

3)

3)

1)

2)

2)

4)

2)

2)

1)

2)2)

2) 2)

2)

3)

1)

1)1)

1)

2)

2)

3)

2)

1)

1)


7) Remove the PWB insulation mylar and remove the paper trans-port detection sensor (POD).

8) Remove two springs and open the intermediate frame unit. (AL-2030/2040CS only)

9) Remove the screw, and open the upper paper guide. (AL-2050CS only)

10) Remove the roller, and remove the belt. (AL-2050CS only)

2)

1)

1)

2)

1)1)

2)

1)

2)


11) Remove the pulleys on the both sides and remove the paperexit roller. (AL-2030/2040CS only)

12) Disengage the pawl, and remove the roller knob.

13) Disengage the pawl, and shift the pulley and the bearing.

14) Remove the paper exit roller, and remove the belt, the pulley,and the bearing.

15) Remove the harness guide.

16) Remove two screws and remove the toner motor.

17) Remove three screws, and remove the DUP motor unit and thebelt. (AL-2040CS/2050CS)

4)

2)

1)3)

1)

2)3)

4)

1)2)

1)

2)

1)

1)

2) 3)


18) Remove five screws and the grounding wire.

For the AL-2030, remove the main drive plate and the belt.For the AL-2040CS/2050CS, remove the main drive plate.

19) Remove the parts as shown below, and remove the pressurerelease solenoid and the paper feed solenoid.

20) Remove four screws, and remove the paper guide unit. (AL-2030/2040CS only)

21) Remove four screws, and remove the lower paper guide unit.(AL-2050CS only)

[Note for installation]

Fit the lower paper guide hole (a) with the shifter gear hole (b)so that the black resin (c) of the shifter unit can be checked.

1)

1)

3)

2)

1)

CAUTION:Attach the gears securely

1)

AL-2030 onlyAL-2030 onlyAL-2030 only

3)

3)

1)

1)

2)

2)

4)

4)

2)

1)

1)

1)

1)

1)1)1)

2)

abc


22) Put the lower paper guide unit upside down, remove twoscrews, and remove the shifter motor. (AL-2050CS only)

23) Remove the screw, and remove the grounding plate and thegear. (AL-2050CS only)

24) Remove the E-ring, the gear, and the bearing, and remove theshifter roller. (AL-2050CS only)

25) Disengage the pawl, and remove the pulley.

26) Shift and remove the shifter unit. (AL-2050CS only)

27) Remove four screws, and remove the LSU unit.

[Note for assembling the LSU]

When installing the LSU, turn the LSU clockwise and fix withscrews in order to provide an attachment backlash in the properdirection.

Observe the following sequence of fixing screws.

1)

2)

1)

2)

3)

1)

2)

3)

3)

4)

1)

1)

1)

2)


28) Remove the screw, slide the left cabinet to the left to detach it.

Remove each pawl, and remove the paper exit tray.

29) Remove two screws and remove the fusing connector.

30) Remove five screws and the connector, and lift the intermediateframe unit to remove.

31) Remove the screw and the E-ring, and remove the PS semi-cir-cular earth plate and the PS roller unit.

32) Remove the E-ring and remove the spring clutch from the PSroller unit.

33) Remove three screws and remove the TC front paper guide.

5)

1)2)

3)

4)

2)

2)

3)

4)

1)

5)

4)

4)

1)

2)

3)

PS roller unit

PS semi-circulerearth plate

5)

4)

4)

1)

2)

3)

PS semi-circularearth plate

Use grease of Floil FG40H only to apply to this section.

1)

2)


34) Remove the screw and the connector, and remove the PPD1sensor PWB.

35) Remove two E-rings and remove the paper feed roller.

36) Remove three E-rings and remove the clutch unit.


6. Manual paper feed sectionA. List

B. Disassembly procedureMulti unit

1) Remove the screw and remove the multi upper cover.

1)

2)

4)

5)

1)

2)

3)

4)

Back

Front

Clutch unit

Paper feedroller

No. Part name Ref.1 Manual transport roller2 Cassette detection switch3 Side door detection unit

2)

1)


2) Remove the screw and remove the side door detection unit.

3) Remove three screws and remove the multi paper feed upperframe.

4) Remove two screws and remove the multi feed bracket unitfrom the multi paper feed upper frame.

5) Remove three E-rings and remove the manual paper feed rollerB9.

1)

2)

Back Wire treatment

1)

2)

1)

2)

2)

1) 1)

2)

1) 1)

1)

3)

L O C K

TO

K


6) Remove the pick-up roller.

7) Cut the binding band and remove the multi paper feed solenoid.


D. Pressure plate holder attachment1) Attach the pressure plate holder so that the resin section is not

covered with the seal M1-N.

7. Rear frame sectionA. List

B. Disassembly procedure1) Remove four screws, and remove the rear cabinet and the rear

cabinet cover.

2)

1)

1)

2)3)Multi paper feedsolenoid

No. Part name Ref.1 Scanner motor2 Main motor3 Exhaust fan motor4 NIC PWB5 Main PWB

Pressure plateholder

Seal M1-N

Attachmentreference

Attachmentreference

1)

1)

2)

2)

1)



3) Remove two screws, and remove the scanner motor.

4) Remove two screws and one harness, and remove the mainmotor.

5) Remove two screws and one connector, and remove theexhaust fan motor.


7) Remove the two screws, and remove the NIC PWB. (AL-2040CS/2050CS only)


9) Remove the three screws, and remove the NIC PWB unit. (AL-2040CS/2050CS only)

10) Disconnect the connectors.

11) Remove the five screws, and remove the MCU PWB. (Theshape of the MCU PWB differs depending on the model.)


1)

2)

3)

1)

2)

3)

1)

2)

3)

Blowing direction

2)

2)

3)

1)

3)

3)

1)2)

2)

2)

3)

2)

2)

2)1)

1)

1)1)

1)

1)


8 Power sectionA. List

B. Disassembly procedure1) Disconnect each connector.

2) Remove the screw, and remove the earth line.

3) Remove two screws, and remove the power PWB unit.


9. Duplex motor section (AL-2040CS/2050CS only)

A. List

B. Disassembly procedure1) Remove the rear cabinet.

2) Remove two screws.

3) Remove the Duplex motor cover.

4) Remove the Duplex motor.

Note: When reassembling, be sure to engage the Duplex motorgear with the belt on the main body side.


10. Reverse roller section (AL-2040CS/2050CS only)

A. List

B. Disassembly procedure1) Remove four screws.

2) Remove the spring, and the earth wire.

3) Remove the reverse unit.

4) Bend the reverse roller and remove it.


No. Part name Ref.1 Power PWB

No. Part name Ref.1 Duplex motor

1) 1)1)

1)

2)

3)

4)

4)5)

1)

12

31

No. Part name Ref.1 Reverse roller

1

2

3

1


11. RSPF section (AL-2050CS only)A. Front cabinet, rear cabinet

(1) Open the upper door unit.

(2) Front cabinet and rear cabinet removal1) Remove two screws.

2) Disengage the five pawls.

3) Remove the front cabinet and the rear cabinet.

B. Upper door unit1) Release the shaft on the front side.

2) Remove the upper door unit.

C. Document tray unit1) Release the shaft on the front side.

2) Remove the tray unit.

Note for reassembly

Use care so that the paper exit Mylar in not pinched between thepaper exit roller and the follower roller.

D. Upper door open/close sensor1) Disconnect one connector.

2) Remove the upper door open/close sensor.

E. Reverse clutch, paper exit roller

(1) Reverse clutch removal1) Disconnect one connector.

2) Remove the resin E-ring.

3) Remove the reverse clutch.

Note for reassembly

Attach the stopper of the reverse clutch along with the rib on themotor mounting plate.

1

1

2

2

222

1

33

1

2

1

2

2

1

1

3

2


(2) Paper exit roller removal1) Remove the E-ring.

2) Slide the bearing.

3) Remove the paper exit roller.

4) Remove the E-ring.

5) Remove the bearing.

F. Drive unit

(1) Transport unit removal1) Disconnect four connectors.

2) Remove the harness from the clamp.

3) Remove the snap band.

4) Remove one screw.

5) Remove the earth wire.


7) Disconnect the RSPF harness.

8) Remove four screws.

9) Remove the transport unit.

Note for reassembly

Before assembly, be sure to check that the harness is passedthrough the rib.

Arrange the RSPF harness to the outside of the base tray so that itis nit pinched before assembly.

(2) Drive unit removal1) Remove three screws.

2) Remove the drive unit.

(3) Drive motor removal1) Remove the gear.


3) Remove the drive motor.

Note for reassembly

Connect the connectors according to the arrow indication markedon the motor mounting plate.

3

41

2

5

1

1

3

6

7

54

1

1

2

8

8

8

9

1

12

1

3

2

1


G. Shutter solenoid

(1) Shutter solenoid unit removal1) Remove the harness from the edge saddle.


3) Remove the shutter solenoid unit.

Note for reassembly

Install the paper feed solenoid under the state where the projectionof the paper feed planet arm is lower than the paper feed solenoidlever.

(2) Shutter solenoid removal1) Remove the paper feed solenoid spring from the shutter sole-

noid.

2) Remove the paper feed solenoid lever.

Note for reassembly

When assembling, use care so that the paper feed solenoid springdoes not extend out of the paper feed solenoid lever.

H. Pickup roller, take-up roller

(1) Paper feed unit removal1) Remove the E-ring.

2) Slide the bearing.

3) Remove the stopper arm.

4) Release the paper feed shaft pressure release spring.

5) Remove the paper feed unit.

6) Remove the paper feed shaft release arm.

(2) Parts removal1) Remove the E-ring.

2) Remove the resin E-ring.

3) Slide the shaft.

4) Remove the spring pin.

(3) Paper feed roller removal1) Pull out the shaft.

2) Remove the clutch boss and the clutch spring from the pickuproller.

2

3

1

2

1

2

1

3

4

5

6

3

1

4

2

1

2


(4) Pickup roller removal1) Disengage one pawl.

2) Remove the pickup drive gear from the pickup roller.

I. Paper empty sensor

(1) Paper feed PG unit removal1) Remove the harness.

2) Remove three screws.

3) Lift the front side, and remove the paper feed PG unit.

(2) Paper feed PG support plate removal1) Remove one screw.

2) Slide and remove the paper feed PG support plate.

(3) Paper empty sensor removal1) Disconnect one connector.

2) Remove the paper empty sensor.

J. PS roller

(1) Parts removal1) Remove the gear.

2) Remove the pulley.

3) Remove the belt.

(2) Parts removal1) Remove one screw.

2) Remove the earth wire.



5) Open the scan plate.

Note for reassembly

Pass the earth wire through the hole to the outside of the frame,then install parts.

1

32

2

3

2

1

2

1

2

1

1

3

2

4

1

5

3

4

2


(3) Scan plate removal1) Remove the scan plate.

(4) PS roller removal1) Remove the PS roller.

K. Upper transport roller

(1) Parts removal1) Remove the gear.

2) Remove the upper transport release arm.




Note for reassembly

Use care so that the rib on the upper transport release arm catchesthe guide.

(2) Upper transport roller removal1) Remove the upper transport roller.

L. Paper sensor1) Disconnect one connector.

2) Remove the paper sensor.

M. Lower transport roller

(1) Reverse self-weight gate removal1) Remove the reverse self-weight gate.

1

1

12 3

5 4

1

2

1

1


(2) Lower transport roller removal1) Remove the E-ring.

2) Remove the gear.


4) Remove the lower transport roller.

N. Paper exit sensor

(1) OC mat removal1) Remove the OC mat.

(2) Paper exit sensor removal1) Disconnect one connector.

2) Remove the paper exit sensor.

12. SPF section (AL-2030/2040CS only)

(1) Rear cabinet disassembly1) Remove four screws.


(2) Remove the SPF.1) Remove two screws, and remove the earth wire.


3) Remove the SPF unit.

A. SPF motor1) Remove the screw.

2) Disengage the pawl (3 positions).


4

12

3

3

1

2

1

No. Part name Ref.A SPF motorB Pick-up roller, paper feed rollerC Paper exit rollerD Set sensor, scan front sensorE Transport roller

1)

2)

3)

1)

3)

2)2)

1)


1) Remove the screw, and remove the harness.


3) Disengage the pawl (4 positions).

4) Remove the transport unit.

1) Remove two screws, and remove the earth wire.

2) Remove the SPF motor unit.



2) Remove the SPF motor.

B. Pick-up roller, paper feed roller1) Remove two gears.

1) Open the upper door.

2) Remove two E-rings, and remove the spring, the arm, and thebearing.

3) Remove the pick-up roller unit.

1) Remove the shaft.

2) Remove the paper feed roller.

3) Remove the bearing and the spring.

2)

2)

3)

3)

1)

4)

1)

2)

1)

1)

3)

1)

2)

1)

1)

1)2)

2)

2)

2)

3)

1)

2)

3)


1) Remove the pick-up roller.

2) Remove the gear.

C. Paper exit roller1) Remove four gears.


3) Remove the frame.



3) Remove the paper guide unit.

4) Remove the paper exit roller.

D. Set sensor, scan front sensor1) Remove the set sensor.

2) Remove the scan front sensor.

3) Disconnect the connectors.

∗ When assembling, attach the blue harness to the marking B sideof the sensor, and attach the orange harness to the opposite sidesensor.

E. Transport roller1) Remove the actuator.

2) Remove the transport roller.

3) Remove the gear and the bearing.

1)

2)

1)

2)

2)

3)

1)

1)

3)

2)

4)

1)

3)

3)

2)B

3)

1)

2)


13. 2nd cassette section (AL-2040CS/2050CS only)

Paper feed unit removal

1) Remove the screw.

2) Remove the rear cover.

∗ When installing, engage the pawl and install the unit.

1) Open the right cabinet.


3) Remove one connector from MCU.

4) While tilting down the 2nd connection arm A, pull and removethe paper feed unit toward you.

∗ When installing, securely insert two bosses C on the machineside and two bosses D on the paper feed unit side. Be sure tosecure the ground wire B.

∗ Insert the 2nd page feed.

A. Paper sensor1) Remove the pawl.

2) Remove the paper sensor.

3) Remove the harness.

No. Part name Ref.A Paper sensorB Cassette detection SWC Paper feed solenoidD Transport rollerE Paper feed clutchF 2nd paper feed roller

1)

1)

2)

2)

1)

12A

1

2

4

B

A

3

2

D

D

C

2

3

1


B. Cassette detection switch1) Remove the pawl.

2) Remove the cassette detection switch.

3) Remove the harness.

C. Paper feed solenoid1) Remove the screw.

2) Remove the connector.

3) Remove the paper feed solenoid.

D. Transport roller1) Remove two E-rings.

2) Remove the transport roller.

∗ Install so that the earth spring A is brought into contact over bear-ing B.

E. Paper feed clutch1) Remove the E-ring.

2) Remove the paper feed clutch.

3) Remove the parts.

∗ When installing, fit the cut surface A.

F. 2nd paper feed roller1) Remove the E-ring and the parts.

2) Remove the 2nd paper feed roller.

∗ When installing, hang the 2nd connection arm on the 2nd con-nection arm Spring B. Be sure to install so that the earth spring Cis in contact under the bearing D.

1

2

3

1

2

3

4

2

1

3AB

A

1

2

3

B

1

2

1

CD

A


[9] ADJUSTMENTS

1. Optical sectionA. Copy magnification ratio adjustmentThe copy magnification ratio must be adjusted in the main scan-ning direction and in the sub scanning direction. To adjust, useSIM 48-1.

(1) OutlineThe main scanning (front/rear) direction magnification ratio adjust-ment is made automatically or manually.

Automatic adjustment: The width of the reference line marked onthe shading correction plate is scanned to perform the main scan-ning (front/rear) direction magnification ratio adjustment automati-cally.

Manual adjustment: The adjustment is made by [Copy quantity]keys (or [Numeric] keys for the AL-2050CS) operations. (In either ofthe automatic and manual adjustments, the zoom data register setvalue is changed for adjustment.)

The magnification ratio in the sub scanning direction is adjusted bychanging the carriage (scanner) scanning speed.

(2) Main scanning direction magnification ratio adjustment

a. Cases when the adjustment is required

1) When the main PWB is replaced.

2) When the EEPROM in the main PWB is replaced.

3) When "U2" trouble occurs.

4) When repairing or replacing the optical section.

b. Necessary tools

• Screwdriver (+)

• Scale

c. Adjustment procedure

1) Set the scale vertically on the document table. (Use a longscale for precise adjustment.)

2) Set the copy magnification ratio to 100%.

3) Make a copy on A4 or 81/2" x 11" paper.

4) Measure the length of the copied scale image.

5) Calculate the main scanning direction magnification ratio. Main scanning direction magnification ratio

6) Check that the copy magnification ratio is within the specifiedrange. If it is not within the specified range, perform the follow-ing procedures.

7) Execute SIM 48-1 to select the main scanning direction copymagnification ratio adjustment mode.To select the adjustment mode, use the [Exposure mode selec-tor] key (or [ ] [ ] key for the AL-2050CS).

In the case of the automatic adjustment, when the START switch ispressed, the mirror base unit moves to the white plate for shadingto scan the width of the reference line, calculating the correctionvalue and displaying and storing this value.

After execution of the automatic adjustment, go out from the simu-lation mode and make a copy to check the magnification ratio.

If the magnification ratio is not in the specified range (100 ± 1.0%),manually adjust as follows.

(AL-2030/2040CS)

(AL-2050CS)

8) Enter the new set value of main scanning direction copy magni-fication ratio with the copy quantity key (or [Numeric] key for theAL-2050CS), and press the [START] key.

9) Change the set value and repeat the adjustment until the ratio iswithin the specified range.When the set value is changed by 1, the magnification ratio ischanged by 0.1%.

(3) Sub scanning direction copy magnification ratio

a. Cases when the adjustment is required

1) When the scanner unit drive section is disassembled or the partis replaced.




b. Necessary tools

• Scale

=Copy image dimensions

X 100 (%)Original dimension

Adjustment mode Display lamp DefaultMain scanning direction magnification ratio

TEXT mode lamp 50

OC mode sub scan direction magnification ratio

PHOTO mode lamp 50

Adjustment modeDisplay

itemLED Default

Main scan direction magnification ratio

F-R PRINT mode lamp 50


SCAN SCAN mode lamp 50

100 110 120 130 150140mm1/2mm

JAPAN

HARDENEDSTAINLESS

Shizuoka

100 110 120 130 150140mm1/2mm

JAPAN

HARDENEDSTAINLESS

Shizuoka

110

10 20

10 20

(When a 100mm scale is used as the original.)

Paper feeddirection

Reference Comparison point

Original (Scale)

Copy

AL-2030/2040CS/2050CS ADJUSTMENTS 9 - 1

c. Adjustment procedure

1) Set the scale on the document table as shown below. (Use along scale for precise adjustment.)

2) Set the copy magnification ratio to 100%.

3) Make a copy on A4 or 81/2" x 11" paper.

4) Measure the length of the copied scale image.

5) Calculate the sub scanning direction copy magnification ratiousing the formula below.

6) Check that the actual copy magnification ratio is within thespecified range. (100 ± 1.0%).If it is not within the specified range, perform the following pro-cedures.

7) Execute SIM 48-1 to select the sub scanning direction copymagnification ratio adjustment mode.To select the adjustment mode, use the [Exposure mode selec-tor] key (or [ ] [ ] key for the AL-2050CS). (PHOTO lampON (or SCAN mode lamp ON for the AL-2050CS))

8) Enter the new set value of sub scanning direction copy magnifi-cation ratio with the [Copy quantity] keys (or [Numeric] keys forthe AL-2050CS), and press the [START] key.

Repeat procedures 1) - 8) until the sub scanning direction actualcopy magnification ratio in 100% copying is within the specifiedrange.

When the set value is changed by 1, the magnification ration ischanged by 0.1%.

B. Image position adjustmentThere are following eleven kinds of image position adjustments,which are made by laser control except for the image scan startposition adjustment. For the adjustments, SIM 50-01 and 50-10 areused.

(AL-2030/2040CS)

To select the adjustment mode with SIM 50-01, use the [Exposuremode selector] key.

The relationship between the adjustment modes and the lightinglamps are as shown in the table below.

: Supported for the installing model and skipped for non-install-ing mode.

To select the adjustment mode with SIM 50-10, use the [Exposuremode selector] key.


Machine with the multi manual paper feed unit

: Supported for the installing model and skipped for non-install-ing mode.

=Copy image dimensions

X 100 (%)Original dimension

100 110 120 130 150140mm1/2mm

JAPAN

HARDDENCDSTAINLESS

Shizuoka

100 110 120 130 150140mm1/2mm

JAPAN

HARDDENCDSTAINLESS

Shizuoka

110

10 20

10 20

Original (Scale)

Paper feeddirection

Reference Comparison point Copy

No. Mode SIM1 Print start position

(Main cassette paper feed)50-01

2 Print start position (2nd cassette paper feed)

50-01 AL-2040CSAL-2050CS

3 Print start position (Manual paper feed) 50-014 Image lead edge void amount 50-015 Image scan start position 50-016 Image rear edge void amount

(Cassette paper feed)50-01

7 Image rear edge void amount (Manual paper feed)

50-01 AL-2050CS

8 Print center offset (Main cassette paper feed)

50-10

9 Print center offset (2nd cassette paper feed)

50-10 AL-2040CSAL-2050CS

10 Print center offset (Manual paper feed) 50-1011 2nd print center offset

(Main cassette paper feed)50-10 AL-2040CS

AL-2050CS

Adjustment mode Lamp ONPrint start position (Main cassette paper feed)

AE, main cassette lamp

Print start position (2nd cassette paper feed)

AE, 2nd cassette lamp

Print start position (Manual paper feed)

AE, manual feed lamp

Image lead edge void quantity TEXT lampImage scan start position PHOTO lampImage rear edge void quantity AE, TEXT, PHOTO lamp

Adjustment mode Lamp ONPrint center offset (Main cassette paper feed)

AE, main cassette lamp

Print center offset (2nd cassette) AE, 2nd cassette lampPrint center offset (Manual paper feed)

AE, manual paper feed lamp

Second side center offset TEXT lamp


(AL-2050CS)

To select the adjustment mode with SIM 50-01, use the [ ] [ ]key.


To select the adjustment mode with SIM 50-10, use the [ ] [ ]key.


(1) Lead edge adjustment1) Set a scale to the center of the paper lead edge guide as shown

below, and cover it with B4 or 8 1/2" x 14" paper.

2) Execute SIM 50-01

3) Set the print start position (AE lamp ON) (A), the lead edge voidamount (TEXT lamp ON) (B), and the scan start position(PHOTO lamp ON) (C) to 0, and make a copy of a scale at100%. (AL-2030/2040CS)

For the AL-2050CS, the following LED’s are lighted:

• AE lamp/COPY mode lamp: (A)

• TEXT lamp/PRINT mode lamp: (B)

• PHOTO lamp/SCAN mode lamp: (C)

4) Measure the image loss amount (R mm) of the scale image.Set C = 10 X R (mm). (Example: Set the value of C to 30.)When the value of C is increased by 10, the image loss isdecreased by 1mm. (Default: 50)

5) Measure the distance (H mm) between the paper lead edgeand the image print start position.Set A = 10 X H (mm). (Example: Set the value of A to 50.)When the value of A is increased by 10, the image lead edge isshifted to the paper lead edge by 1mm. (Default: 50)

6) Set the lead edge void amount to B = 50 (2.5mm).When the value of B is increased by 10, the void amount isincreased by about 1mm. For 25 or less, however, the voidamount becomes zero. (Default: 50)

(2) Image rear edge void amount adjustment1) Set a scale to the rear edge section of A4 or 11" x 8 1/2" paper

size as shown in the figure below, and cover it with B4 or 8 1/2"x 14" paper.

2) Execute SIM 50-01 to select the image rear edge void amountadjustment mode.The set adjustment value is displayed on the copy quantity dis-play.

3) Make a copy and measure the void amount of image rear edge.

Adjustment mode Display item Lamp ONPrint start position (Main cassette paper feed)

TRAY1 COPY mode lampMain cassette lamp

(*) Print start position (2nd cassette paper feed)

TRAY2 COPY mode lamp2nd cassette lamp


MFT COPY mode lampManual paper feed lamp

Image lead edge void amount

DEN-A PRINT mode lampMain cassette lamp

Image scan start position RRC-A SCAN mode lampMain cassette lamp

Image rear edge void amount (Cassette paper feed)

DEN-B COPY mode lampPRINT mode lampSCAN mode lampMain cassette lamp

Image rear edge void amount (Manual paper feed)

RRC-B COPY mode lampPRINT mode lampManual paper feed lamp

Adjustment mode Display item Lamp ONPrint center offset (Main cassette paper feed)


Print center offset (2nd cassette paper feed)


Print center offset (Manual paper feed)


2nd print center offset (Main cassette paper feed)

SIDE2 PRINT mode lampMain cassette lamp

5mm

10mm

(Example)Distance between paper leadedge and image: H = 5mm

Image loss:R = 3mm

B4 or 8 1/2″ × 14″ paper

A4 size rear edge

Paper rear edge

Void amount (Standard value: 2 - 3mm)

Scale image


4) If the measurement value is out of the specified range, changethe set value and repeat the adjustment procedure.The default value is 50.

Note: The rear edge void cannot be checked with the first sheetafter entering the simulation mode, the first sheet after turn-ing off/on the power, or the first sheet after inserting thecassette. Use the second or later sheet to check the rearedge void.

(3) Center offset adjustment1) Set the self-made test chart for the center position adjustment

so that its center line is aligned with the center mark of the doc-ument guide.

• Test chart for the center position adjustment.Draw a line at the center of A4 or 8 1/2" x 11" paper in the papertransport direction.

2) Execute SIM 50-10 to select the print center offset (cassettepaper feed) adjustment mode.The set adjustment value is displayed on the copy quantity dis-play.

3) Make a copy and check that the copied center line is properlypositioned.The standard value is 0 ± 2mm from the paper center.

4) If the measured value is out of the specified range, change theset value and repeat the adjustment procedure.When the set value is increased by 1, the copy image isshifted by 0.1mm toward the rear frame.

• For the manual paper feed, change the manual paper feedadjustment mode and perform the similar procedures.

• Since the document center offset is automatically adjusted bythe CCD which scan the reference lines (F/R) on the back ofdocument guide, there is no need to adjust manually.

2. Copy density adjustmentA. Copy density adjustment timingThe copy density adjustment must be performed in the followingcases:

• When maintenance is performed.

• When the developing bias/grid bias voltage is adjusted.

• When the optical section is cleaned.

• When a part in the optical section is replaced.

• When the optical section is disassembled.

• When the OPC drum is replaced.

• When the main control PWB is replaced.

• When the EEPROM on the main control PWB is replaced.

• When the memory trouble (U2) occurs.

B. Note for copy density adjustment1) Arrangement before execution of the copy density adjustment

• Clean the optical section.

• Clean or replace the charger wire.

• Check that the voltage at the high voltage section and the devel-oping bias voltage are in the specified range.

C. Necessary tool for copy density adjustment• One of the following test charts:

UKOG-0162FCZZ, UKOG-0089CSZZ, KODAK GRAY SCALE

• B4 (14" x 8 1/2") white paper

• The user program AE setting should be "3."

Test chart comparison table

D. Features of copy density adjustmentFor the copy density adjustment, the image data shift function pro-vided in the image process LSI is used.

List of the adjustment modes

Document guide

Center

Copy paper(A4 or 8 1/2″ × 11″)

(Copy A)

(Copy B)

2.0mm or less

2.0mm or less

Copy image

Copy paperfolding line

Copy image

Copy paperfolding line

Shift

Shift

(Paper feed direction)

UKOG-0162FCZZDENSITYNo.

1 2 3 4 5 6 7 8 9 10 W

UKOG-0089CSZZDENSITYNo.

0.1 0.2 0.3 0.5 1.9 0

KODAKGRAYSCALE

1 2 3 4 19 A

Auto mode Brightness 1 step onlyManual mode Brightness 5 steps. Adjustment of only the

center brightness is made.Photo mode Brightness 5 steps. Adjustment of only the

center brightness is made.Manual T/S mode Brightness 5 steps. Adjustment of only the

center brightness is made.T/S Auto mode Brightness 1 step only

1 10 W2 3 4 5 6 7 8 9


E. Copy density adjustment procedureUse SIM 46-1 to set the copy density for each copy mode.

For selection of modes, use the [Exposure mode selector] key (or[ ] [ ] key for the AL-2050CS).

(1) Test chart (UKOG-0162FCZZ) setting1) Place the test chart so that its edge is aligned with the A4 (Let-

ter) reference line on the document table. Then place a A4(14" x 8 1/2") white paper on the test chart and close the docu-ment cover.

(2) Perform the adjustment in each mode.1) Execute SIM 46-01 (300dpi). To adjust in 600dpi, execute SIM

46-02.

2) AL-2030/2040CS

Select the mode to be adjusted with the exposure mode selectkey. Set the exposure level to 3 for all adjustment. (Except forthe auto mode.)

2) AL-2050CS

Select the mode to be adjusted with the exposure key. Set theexposure level to 3 (center) for all adjustment. (Except for theauto mode.)

3) Make a copy.Check the adjustment level (shown in the above table) of theexposure test chart (Sharp Gray Scale).

(When too bright): Decrease the value displayed on the copyquantity display.

(When too dark): Increase the value displayed on the copy quan-tity display.

∗ The value can be set in the range of 1 - 99.

3. High voltage adjustmentA. Main charger (Grid bias)Note:

• Use a digital multi meter with internal resistance of 10MΩ ormore measurement.

• After adjusting the grid LOW output, adjust the HIGH output. Donot reverse the sequence.

Procedures

1) Set the digital multi meter range to DC700V.

2) Set the positive side of the test rod to the connector CN11-3(GRID) of high voltage section of the power PWB and set thenegative side to the frame ground (power frame).

3) Execute SIM 8-2. (The main charger output is supplied for 30sec in the grid voltage HIGH output mode.)

4) Adjust the control volume (VRG1) so that the output voltage is580 ± 12V.

Adjustment mode

Exposure modedisplay lamp

Sharp gray chart adjustment level

Auto mode Auto lamp ON "3" is slightly copied.

Manual mode Manual lamp ON "3" is slightly copied.

Photo mode Photo lamp ON "3" is slightly copied.

Manual T/S mode

Manual lamp/Photo lamp ON "3" is slightly copied.

Auto T/S mode

Auto lamp/Photo lamp ON "3" is slightly copied.

Test chart

White paper

(1) (2)

Exposure mode select key/display lamp

[Exposure mode selector] key/display lamp

(1)

(2)

(2) Exposure key

(1) Exposure mode, level displayTEXT | | | | |

Adjustment mode

Display item

LEDSharp gray chart adjustment level

Auto mode AE COPY mode lamp "3" is slightly copied.

Text mode TEXT PRINT mode lamp "3" is slightly copied.

Photo mode PHOTO SCAN mode lamp "3" is slightly copied.

Text T/S mode TSTXT PRINT mode lampSCAN mode lamp

"3" is slightly copied.

Auto T/S mode TSAE COPY mode lampSCAN mode lamp

"3" is slightly copied.

Sharp Gray Scale adjustment level

Non toner save mode

Toner save mode

1 10 W2 3 4 5 6 7 8 9

Slightly copied.

Not copied.

1 10 W2 3 4 5 6 7 8 9

Slightly copied.

Not copied.

VRG1


B. DV bias check

Procedures

1) Set the digital multi meter range to DC500V.

2) Set the positive side of the test rod to the connector CN-10-1(DV BIAS) and set the negative side to the frame ground(power frame).

3) Execute SIM 8-1 to output the developing bias for 30sec, andcheck that the output is –400 ± 8V.

4. Duplex adjustmentA. Adjusting the paper reverse position in

memory for duplex copyingThis step adjusts the front surface printing (odd-number pages of adocument set) in the S-D mode copying and the leading edge posi-tion of an image on even-number pages in the D-S mode.

That is, it covers the adjustment of the second surface printingmode (image loss at the front edge of an image) in which imagedata is once stored in memory.

The image data is read, starting from its front end in the documentdelivery direction (Reference direction of document setting in theOC mode)and stored in memory.

This stored image data is printed starting at the printing start posi-tion, in the order of last-stored data to the first-stored data.

In other words, the front edge image loss of the image can beadjusted by changing the document read end position.

(Adjustment procedure)

1) Preparing test chart (Draw a scale at the rear end of one side ofa sheet of A4 white paper or letter paper)

2) Set the test chart so that the scale is positioned as shownbelow, in the S-D mode and the D-S mode.

3) Execute simulation 50-18.

Select the SPF/RSPF memory reverse output position, andpress [START] key to make a copy.

Adjust the setting so that the front edge image loss is less than4.0 mm in the SPF/RSPF mode.An increase of 1 in setting represents an increase of 0.1 mm inimage loss.

B. Adjusting trailing edge void in duplex copy mode

This is the adjustment of the first surface printing mode (rear endvoid) in duplex copying.

In a duplex copying operation, the paper is delivered starting fromthe rear end of the first printing surface. It is therefore necessary tomake a void area at the rear end on the first printing surface to pre-vent paper jam at the fusing part.

There are two adjustment modes:

1) Paper trailing edge void quantity 50-19 (TEXT)This adjustment is made when the cassette paper size is rec-ognized. The trailing edge void quantity can be adjusted bychanging the trailing edge image laser OFF timing.

Note: • A digital multi meter with internal resistance of 1GΩ mustbe use for correct check.

• The adjustment volume is locked, and no adjustment canbe made.

VRDV

5 10

Mode Display item Default LEDOC memory reverse output position

OC 50 COPY mode lamp

SPF/RSPF memory reverse output position

SPF 50 PRINT mode lamp

Scale (S-D mode) Scale (D-S mode)

5 10

The front edge of thescale on test chart

Front edge of paper

Void area

less than 4 mm

2nd printing surface where scale is printed (lower side)


2) Print start position (Duplex back surface) (SPF/RSPF) 50-19(PHOTO)The size (length) of a document read from the SPF/RSPF isdetected, the image at the trailing edge of the first printing sur-face is cut to make a void area. (The adjustment of void quantityat the time when the cassette paper size is not recognized.)

The paper void quantity should be first adjusted before the imagecut trailing edge void quantity (SPF/RSPF) is adjusted.

(Adjustment procedure)

(1) Paper trailing edge void quantity1) Preparing test chart (Draw a scale at the rear end of one side

of a sheet of A/4 white paper or letter paper)

2) Set the test chart on the document glass as shown below.

3) Using the user simulation [18], set the paper size of the firstcassette.

• Letter paper: 4

• A4 paper: 3

4) Execute SIM 50-19 to turn on the TEXT lamp (or PRINT modelamp for the AL-2050CS) and make the printing mode in OC-Dmode.Make a copy of the test chart to check the void area of the scaleon the image.

Adjust the setting so that the void area is 4 - 5 mm. An increase in1 of setting represents 0.1 mm in void area.

(2) Print start position (Duplex back surface)1) Set the test chart so that the scale is positioned as shown

below.

2) Execute SIM 50-19 to turn on the PHOTO lamp (or SCAN modelamp for the AL-2050CS) and make the printing mode in the S-D mode.

3) Remove and reinsert the cassette.

Note: Make sure to carry out this step before making a copy dur-ing this adjustment.

4) Make a copy and check the void area of the scale on theimage.Adjust the setting so that the void area is 2 - 4 mm. Anincrease of 1 in setting represents an increase of 0.1 mm invoid area.Void position to be checked

5. SPF/RSPF scan position automatic adjustment

Place a A4 paper (white chart) so that it covers the SPF scan glassand the OC glass together, and close the SPF/RSPF.

When simulation 53-08 is executed, the current adjustment value isdisplayed as the initial display.

* Default is 1. Adjustment range is 1 – 99. Adjustment unit 1 =about 0.127mm

* If the values are kept as the default values, SPF/RSPF scan isnot performed properly. The front area of the proper scan positionmay be scanned.

In case of AUTO, press [START] key, and the mirror unit scans fromthe home position to the SPF/RSPF scan position with the adjust-ment value displayed. The SPF glass cover edge position is calcu-lated from the difference between the SPF glass cover edge andthe OC side document glass CCD output level. If the adjustment isnormal, the adjusted value is displayed. If abnormal, the error LEDlights up with the current set value displayed.

During the error LED is lighted, when [START] key is pressed again,execution is performed again.

Operation

The operation is similar to simulation 46-01. (In MANUAL)OK/ERR display in AUTO (AL-2050CS only)

Document guide The trailing edge has a scale

Table glass

The trailing edge void on the first printing surface is shown above.

Paper

Void position to be check

Scale (S-D mode)

ModeDisplay

itemDefault LED

SPF/RSPF scan position auto adjustment

AUTO 1 AE mode lamp (AL-2030/2040CS)COPY mode lamp (AL-2050CS)

SPF/RSPF scan position manual adjustment

MANU 1 TEXT mode lamp (AL-2030/2040CS)PRINT mode lamp (AL-2050CS)

<When OK> <When ERR>

53-08 SPF AUTOAUTO 100% ** OK

53-08 SPF AUTOAUTO 100% ** ERR

6cm or more is required.


6. SPF/RSPF mode sub scanning direction magnification ratio adjustment

Note: Before performing this adjustment, be sure to check that theOC mode adjustment in copying has been completed.

1) Put a scale on the original table as shown below, and make anormal copy (100%) on the front and the back surfaces tomake a test chart.

Note: Since the printed copy is used as a test chart, put the scalein paralled with the edge lines.

2) Set the test chart on the SPF and make a copy in the normalratio (100%). (AL-2030/2040CS)

Set the test chart on the RSPF and make a duplex copy (D-D orD-S) in the normal ratio (100%). (AL-2050CS)

3) Compare the scale image and the actual image.If necessary, perform the following adjustment procedures.

4) Execute SIM 48-05.

5) The current sub scanning direction magnification ratio correc-tion value is displayed in two digits on the display section.

6) Enter the set value and press the [START] key.

When adjusting the RSPF, use [2-SIDED COPY] key to selectsingle/duplex after entering the one page print mode, perform-ing 2-page single copy.

∗ When there is no document in SPF/RSPF, copy is inhibited.

<Adjustment specification>

7. Automatic black level correctiona. Cases when the adjustment is required




4) When repairing or replacing the optical section.

b. Adjustment procedure

Used to acquire the black level target value used for the black leveladjustment of white balance.

When SIM 63-02 is executed, the current correction value is dis-played in 3 digits of 12bit hexadecimal number.

Place the gray gradation chart (UKOG-0162FCZZ) used as thecorrection document so that the density 10 (black side) comes onthe left side and that the chart is upside down at the center of theplate left center.

When START key is pressed, the mirror base unit scans the chartand calculates the correction value.

After completion of correction, the corrected value is displayed onthe display section.

∗ Default: 0

∗ If the value is set to the default, operation is made with 0x60.

AL-2050CS only

c. Operation

1) Initial display

2) [ENTER]/[START] key: Correction start

<During canceling - When [Clear]/[Clear All] key is pressed->

After canceling, the machine goes into the sub code entry standbymode.

3) After execution

3) In case of an error

ModeDisplay item (AL-2050CS)

Default LED

Sub scan magnification ratio adjustment on the surface of SPF/RSPF document

SIDE1 50 AE mode lamp (AL-2030/2040CS)COPY mode lamp (AL-2050CS)

Sub scan magnification ratio adjustment on the surface of RSPF document (AL-2050CS only)

SIDE2 50 PRINT mode lamp

Adjustment mode Spec value SIM Set valueSetting range

Sub scanning direction magnification ratio (SPF/RSPF mode)

At normal: ±1.0%

48-5 Add 1: 0.1% increaseReduce 1: 0.1% decrease

1 – 99

63-02 BLACK LEVEL 0

63-02 BLACK LEVELEXECUTING...

THE JOB IS BEINGCANCELED.

63-02 BLACK LEVEL *** OK

63-02 BLACK LEVEL *** ERR

Chart back surface

10


[10] SIMULATION, TROUBLE CODES

1. Entering the simulation modeTo enter the serviceman simulation mode, press the keys as fol-lows:

AL-2030/AL-2040CS

[Clear] key → Exposure mode selector key → [Clear] key → Exposure mode selector key

AL-2050CS

[#] key → [∗] key → [Clear] key → [∗] key

To cancel the simulation mode, press the [Clear All] key.

2. Key ruleAL-2030/AL-2040CS

AL-2050CS

3. List of simulations

[ ] [ ] key: Entry of MAIN CODE/SUB CODESetting of the adjustment values for the adjustment-related simulationsWhen [%] key is pressed simultaneously, the value is displayed in the descending sequence such as [0] → [9], not as [0] → [1].

[START] key: Settlement<In case of simulations for print>[START] key: Settlement / Print

[Exposure mode selector] key: Selection of an item

[Clear] key: (Interrupting operation check) Returns to the upper hierarchy.On the initial display (00-00), it terminates the simulation.Exits from the simulation mode.For a simulation of adjustment, the display returns to the initial display (00-00).

[Numeric] key: Entry of MAIN CODE/SUB CODESelection of an itemSetup of an adjustment value in case of simulations for adjustment

[ ] [ ] key: Selection of MAIN CODE/SUB CODESelection of an item

[ENTER]/[START] key: Settlement<In case of simulations for print>[ENTER] key: Settlement (Without print)[START] key: Settlement / Print

[Clear] key: (Interrupting operation check) Returns to the upper hierarchy.In case of simulation of operation check, terminates the operations.

[Clear All] key: Exits from the simulation mode.For a simulation of adjustment, the display returns to the initial display (00-00).

Sim No.

Sub code

Operation

01 01 Mirror scan operation02 Mirror home position sensor (MHPS) status display06 Aging of mirror scanning

02 01 SPF/RSPF aging operation02 SPF/RSPF sensor status display03 SPF/RSPF Motor ON06 Resist clutch ON (SPF) (AL-2030/2040CS only)08 RSPF paper feed solenoid operation check

(AL-2050CS only)09 RSPF reverse solenoid operation check

(AL-2050CS only)03 03 Shifter operation check (AL-2050CS only)05 01 Operation panel display check

02 Fusing lamp, cooling fan operation check03 Copy lamp ON

06 01 Paper feed solenoid ON02 Resist solenoid ON

07 01 Warm-up display and aging with jam06 Intermittent aging08 Shift to copy with the warm-up display

08 01 Developing bias02 Main charger (Grid high)03 Grid voltage (Low)06 Transfer charger

09 01 Duplex motor normal rotation operation check (AL-2040CS/2050CS only)

02 Duplex motor reverse operation check (AL-2040CS/2050CS only)

04 Duplex motor rotation speed adjustment (AL-2040CS/2050CS only)

10 Toner motor aging14 Cancel of troubles other than U216 Cancel of U2 trouble22 04 JAM total counter display

05 Total counter display08 SPF/RSPF counter display12 Drum counter display14 ROM version display16 Duplex counter display (AL-2040CS/2050CS only)17 Copy counter display18 Printer counter display19 Scanner mode counter display

(AL-2040CS/2050CS only)21 Scanner counter display22 SPF/RSPF JAM counter display

24 01 JAM total counter clear04 SPF/RSPF counter clear05 Duplex counter clear (AL-2040CS/2050CS only)07 Drum counter clear08 Copy counter clear09 Printer counter clear13 Scanner counter clear14 SPF/RSPF JAM total counter clear15 Scanner mode counter clear

(AL-2040CS/2050CS only)25 01 Main motor operation check

(Cooling fan motor rotation check)10 Polygon motor ON

AL-2030/2040CS/2050CS SIMULATION, TROUBLE CODES 10 - 1

4. Descriptions of various simulations

Sim No.

Sub code

Operation

26 02 SPF/RSPF setup03 Second cassette setup04 Machine duplex setup06 Destination setup07 Machine conditions check20 Rear edge void setup30 CE mark support control ON/OFF38 Cancel of stop at drum life over39 Memory capacity check40 Polygon motor OFF time setup (Time required for

turning OFF after completion of printing)42 Transfer ON timing control setup43 Side void setup54 γ life correction setting62 Energy-save mode copy lamp setup

30 01 Paper sensor status display41 06 OC cover float detection level adjustment

07 OC cover float detection margin setting43 01 Fusing temperature setting (Normal copy)

04 Fusing temperature setting in multi copy05 Fusing temperature setup in duplex copy

(AL-2040CS/2050CS only)14 Fusing start temperature setting

46 01 Copy density adjustment (300dpi)02 Copy density adjustment (600dpi)18 Image contrast adjustment (300dpi)19 Exposure mode setup20 SPF/RSPF exposure correction

Sim No.

Sub code

Operation

46 29 Image contrast adjustment (600dpi)30 AE limit adjustment31 Image sharpness adjustment32 Copier color reproduction setup

48 01 Front/rear (main scanning) direction and scan (sub scanning) direction magnification ratio adjustment

05 SPF/RSPF mode sub scan direction magnification ratio in copying

49 01 Flash ROM program writing mode50 01 Lead edge image position

06 Copy lead edge position adjustment (SPF/RSPF)10 Center offset adjustment12 Document off-center adjustment18 Memory reverse position adjustment in duplex

copy (AL-2040CS/2050CS only)19 Duplex copy rear edge void adjustment

(AL-2040CS/2050CS only)51 02 Resist quantity adjustment53 08 SPF/RSPF scan position automatic adjustment61 03 Polygon motor check (HSYNC output check)63 01 Shading check

02 Black level automatic correction12 Light quantity stabilization wait time setting13 Light quantity stabilization band setting

64 01 Self print67 50 USB receive speed adjustment (USB1.1)

(AL-2030/2040CS only)

Main code

Sub code

Contents Details of function/operation

1 01 Mirror scan operation [Function]When [ENTER]/[START] key is pressed, the home position is checked and the mirror base per-forms full scan at the speed of the set magnification ratio.

During operation, the set magnification ratio is displayed.

The mirror home position sensor status is displayed with the "Drum replacement required lamp(or the copy mode indicator for the AL-2050CS)". (When the mirror is in the home position, thelamp lights up.)

During operation, the copy lamp lights up.

When [Clear] key is pressed, if the operation is on the way, it is terminated and the machinegoes to the sub code entry standby mode.

[Operation] (AL-2050CS only)

02 Mirror home position sensor (MHPS) status display

[Function]Monitors the mirror home position sensor, and makes the "Drum replacement required lamp (orthe copy mode indicator for the AL-2050CS)" turn on during the sensor ON status.


1) Initial display 2) [ZOOM] key

2) [ ] key

2) [ ] key

3) [ENTER]/[START] key

01-01 SCAN CHK - 100% +

01-01 SCAN CHK - 78% +

01-01 SCAN CHK - 99% +

01-01 SCAN CHK - 101% +

01-01 SCAN CHKEXECUTING... - 78% +

1) Initial display

01-02 MHP-SENSOREXECUTING...


1 06 Aging of mirror scanning [Function]When [ENTER]/[START] key is pressed, the mirror base performs full scan at the speed of theset magnification ratio.

During operation, the set magnification ratio is displayed.

After 3sec, the mirror base performs full scan again.

∗ When [ENTER]/[START] key is pressed once, the ready lamp remains OFF.The mirror home position sensor status is displayed on the "Drum replacement required lamp(or the copy mode indicator for the AL-2050CS)." (The lamp is ON when the mirror is in thehome position.)

During aging, the copy lamp is ON.

[Operation] (AL-2050CS only)The operation is similar to simulation 1-01.

2 01 SPF/RSPF aging operation [Function]When [ENTER]/[START] key is pressed, the set magnification ratio is obtained. For the SPF, thesingle-face document transport is performed. For the RSPF, the duplex document transport isperformed.

However, the operating conditions don't matter and the operation is not stopped even in case ofa jam. Also the magnification ratio is displayed on the LCD/display.


02 SPF/RSPF sensor status display

[Function]The ON/OFF status of the SPF/RSPF sensors can be checked with the LCD/LED.When a sensor is ON, the sensor name is displayed on the LCD/LED.


03 SPF/RSPF Motor ON [Function]When [ENTER]/[START] key is pressed, the motor rotates for 10sec at the speed correspond-ing to the set magnification ratio.


06 Resist clutch ON (SPF) (AL-2030/2040CS only)

When the [START] key is pressed, the SPF resist clutch (SRRC) repeats ON (500 ms) and OFF (500 ms) 20 times.

08 RSPF paper feed solenoid operation check (AL-2050CS only)

[Function]The RSPF paper feed solenoid (SPUS) repeats ON for 500ms and OFF for 500ms 20 times bythe use of the solenoid drive control Bios.


09 RSPF reverse solenoid operation check (AL-2050CS only)

[Function]The RSPF reverse solenoid (SPFS) repeats ON for 500ms and OFF for 500ms 20 times by theuse of the solenoid drive control Bios.


Main code

Sub code


SensorDisplay item AL-2050CS

Display itemAL-2030/2040CS

Document set sensor SPID TD cartridge replacement required lamp

RSPF document transport sensor SPPD Misfeed lampRSPF paper feed cover open/close sensor

SDSW —

RSPF paper exit sensor SPOD —

1) Initial display 2) When the sensor is ON:

02-02 SPF SENSOR 02-02 SPF SENSORSPID SPPD SDSW SPOD

1) Initial display

02-08 SPF SPUS CHKEXECUTING...

1) Initial display

02-09 RSPF SPFS CHKEXECUTING...


3 03 Shifter operation check (AL-2050CS only)

[Function]The shifter is moved back and forth in four reciprocations.


5 01 Operation panel display check

[Function]<LED check mode (All ON/Individual ON)>When [ENTER]/[START] key is pressed, all the LCD's on the operation panel are turned ON (allpixels ON).After 5sec of ON, the machine goes into the sub code entry standby mode.When [Mode Select] key is pressed under the all ON state, the mode is shifted to the individualON mode, where the LED's are turned on one by one from the left upper end to the left lowerside then from the right upper side to the right lower side. (All the pixels of LCD are lightedsimultaneously.) After lighting all the LCD's sequentially, all the LCD's are lighted simulta-neously. After 5sec from lighting all the LCD's simultaneously, the machine goes into the subcode entry standby mode. (Cycle of individual ON mode: ON 300ms, OFF 20ms)

When [Clear] key is pressed in the LED check mode, the machine goes into the sub code entrystandby mode.When [START] key is pressed, the machine goes into the key input check mode.

<Key input check mode>When the machine goes into the key input check mode, the value display section indicates "– ––" (For the AL-2050CS, 0 of the LCD is indicated).When any key is pressed after pressing a key on the operation panel, "+1" is added to thevalue.Once a key is pressed, it is not recounted.When [START] key is pressed, counting is made and the machine goes into the LED ON checkmode (LED all ON status) after 3sec.When [Clear] key is pressed for the first time, it is counted. When it is pressed for the secondtime, the key check mode is retained as well as when another key is pressed.

(Note in the key input check mode)• Be sure to press [START] key at the last. (If it is pressed on the way, the machine goes into

the LED ON check mode.) (LED all ON status)

• Multi key input is ignored.

[Operation] (AL-2050CS only)<LED check mode (All ON/Individual ON)>

<Key input check mode>

02 Fusing lamp, cooling fan operation check

[Function]When [ENTER]/[START] key is pressed, the fusing lamp repeats ON for 500ms and OFF for500ms 5 times. During this period, the cooling fan motor rotates.


03 Copy lamp ON [Function]When [ENTER]/[START] key is pressed, the copy lamp turns ON for 5sec.


Main code

Sub code


1) Initial display

03-03 SHIFTER CHKEXECUTING...

1) Initial display

2) When [Mode Select] key is pressed, the machine goes into the individual ON mode.

1) Initial display 2) [ENTER/START] key

05-01 LCD/LED CHK. 0

05-01 LCD/LED CHK. **

1) Initial display

05-02 HT LAMP CHKEXECUTING...

1) Initial display

05-03 C-LAMP CHKEXECUTING...


6 01 Paper feed solenoid ON [Function]When [ENTER]/[START] key is pressed, the selected paper feed solenoid repeats ON for500ms and OF for 500ms 20times.

When tray select key (or [Numeric] key or [ ] [ ] key for the AL-2050CS) is pressed, thepaper feed solenoid setting is switched.


02 Resist solenoid ON [Function]When [ENTER]/[START] key is pressed, the resist solenoid repeats ON for 500ms and OFF for500ms 20 times.


7 01 Warm-up display and aging with jam

[Function]Copying is repeated to make the set quantity of copies.When the simulation is executed, warm-up is started and warm-up time is added for every sec-ond from 0 and displayed.When warm-up is completed, addition is stopped. When [Clear All] key is pressed, the readylamp lights up.After that, enter the copy quantity with [ ] [ ] key (or [Numeric] key for the AL-2050CS) andpress [ENTER]/[START] key to repeat copying of the set quantity (interval 0sec).To cancel the simulation, turn off the power or execute a simulation which causes hardwarereset.


06 Intermittent aging [Function]Copying is repeated to make the set quantity of copies.When the simulation is executed, warm-up is performed and the ready lamp is lighted.Enter the copy quantity with the [ ] [ ] key (or [Numeric] key for the AL-2050CS) and press[ENTER]/[START] key, and copying is executed to make the set quantity of copies, and theready state is kept for 3sec, and copying is executed again to make the set quantity of copies.These operations are repeated.To cancel the simulation, turn off the power or execute a simulation which executes hardwarereset.


Main code

Sub code


Code number Setting Remark0 CPFS11 CPFS2 Operation is possible only when No. 2 cassette is installed. 2 MPFS

1) Initial display 2) [Numeric] key or [ ] key

2) [Numeric] key or [ ] key


4) Returns to the initial display.

06-01 PSOL CHK0:CPFS1

06-01 PSOL CHK1:CPFS2

06-01 PSOL CHK2:MPFS

06-01 PSOL CHKEXECUTING...

1) Initial display

06-02 RES.R SOL CHKEXECUTING...

1) Initial display 2) After 10sec

07-01 W-UP/AGING 0

07-01 W-UP/AGING 10

1) Initial display (Basic display of copy)

READY TO COPY 100% A4 0


7 08 Shift to copy with the warm-up display

[Function]Enter the simulation code, and warm-up is started and warm-up time is counted for every sec-ond from 0 and displayed.When [Clear All] key is pressed during counting up, "0" is displayed on the display and countingis stopped. However, warm-up is continued.After completion of warm-up, counting is terminated. (The aging function is removed from simu-lation 7-01.)


8 01 Developing bias [Function]When [ENTER]/[START] key is pressed, the developing bias signal is turned ON for 30sec.

When, however, an actual output value is measured, use simulation 25-01.

After completion of this process, the machine goes into the sub code entry standby mode.


02 Main charger (Grid high) [Function]When [ENTER]/[START] key is pressed, the main charger is outputted for 30sec in the grid volt-age HIGH move.



03 Grid voltage (Low) [Function]When [ENTER]/[START] key is pressed, the main charger is outputted for 30sec in the grid volt-age LOW move.



06 Transfer charger [Function]When [ENTER]/[START] key is pressed, the transfer charger is outputted for 30sec.



9 01 Duplex motor normal rotation operation check (AL-2040CS/2050CS only)

[Function]Use the duplex motor Bios to drive the duplex motor in the normal direction (paper exit direc-tion) for 30sec.



02 Duplex motor reverse operation check (AL-2040CS/2050CS only)

[Function]Use the duplex motor Bios to drive the duplex motor in the reverse direction for 30sec.



Main code

Sub code


1) Initial display 2) After 10sec

07-08 W-UP C-MODE 0

07-08 W-UP C-MODE 10

1) Initial display

08-01 DVLP BIAS SET.EXECUTING...

1) Initial display

08-02 MHV(H) SET.EXECUTING...

1) Initial display

08-03 MHV(L) SET.EXECUTING...

1) Initial display

08-06 THV SET.EXECUTING...

1) Initial display

09-01 DPLX ROT.EXECUTING...

1) Initial display

09-02 DPLX ROT.REV.EXECUTING...


9 04 Duplex motor rotation speed adjustment (AL-2040CS/2050CS only)

[Function]When this simulation is executed, the currently set value is displayed.Enter the adjustment value with [ ] [ ] key (or [Numeric] key for the AL-2050CS) and press[ENTER]/[START] key. The entered value is stored and the machine goes into the sub codeentry standby mode. The greater the set value is, the higher the speed is. The smaller the setvalue is, the lower the speed is. (Setting range: 1 - 13, Default: 6)

[Operation]

10 Toner motor aging [Function]When [ENTER]/[START] key is pressed, the toner motor is rotated for 30sec.After completion of this process, the machine goes into the main code entry standby mode.


14 Cancel of troubles other than U2

[Function]Used to cancel troubles other than U2.∗ Cancel troubles such as H trouble which writes data into EEPROM, and perform hardware

reset.


16 Cancel of U2 trouble [Function]Used to cancel U2 trouble.When [ENTER]/[START] key is pressed, check sum of the total counter in the EEPROM isrewritten and hardware reset is made.


22 04 JAM total counter display [Function]The JAM total counter is displayed.

[Operation]

05 Total counter display [Function]The total counter value is displayed.

[Operation]

Main code

Sub code


AL-2050CS

1) Initial display

2) [Numeric] key

3) [ENTER/START] key

AL-2040CS

1) Press [ ] [ ] key to change the code number.

2) Press [START] key to fix the code number.09-04 DPLX ROT.SPEED 6( 1-13)

09-04 DPLX ROT.SPEED 5( 1-13)

09-04 DPLX ROT.SPEED 5( 1-13)

1) Initial display

10-00 TONER MOTOREXECUTING...

1) Initial display

14-00 TRBL CANC.CLEARED

1) Initial display

16-00 U2 TRBL CANC.CLEARED

AL-2050CS

1) Initial display

AL-2030/2040CS

The count value is displayed in 3 digits X 2times repeatedly.

<Display example: 12345>22-04 JAM TTL CNT ***,***

012 → Blank → 345 → Blank → 0120.7s 0.3s 0.7s 1.0s 0.7s

AL-2050CS

1) Initial display

AL-2030/2040CS

The operation is similar to simulation 22-04.

22-05 TTL CNT ***,***


22 08 SPF/RSPF counter display [Function]The SPF/RSPF counter is displayed.

[Operation]

12 Drum counter display [Function]The drum counter is displayed.

[Operation]

14 ROM version display [Function]The P-ROM version is displayed.Press [ ] [ ] key (or [Numeric] key or [ ] [ ] key for the AL-2050CS) to switch the display version.

[Operation]

16 Duplex counter display (AL-2040CS/2050CS only)

[Function]The duplex counter is displayed.

[Operation]

17 Copy counter display [Function]The copy counter is displayed.

[Operation]

18 Printer counter display [Function]The printer counter is displayed.

[Operation]

Main code

Sub code


AL-2050CS

1) Initial display

AL-2030/2040CS


22-08 SPF CNT ***,***

AL-2050CS

1) Initial display

AL-2030/2040CS


22-12 DRUM CNT ***,***

Code number Version Display item0 Main unit Program MAIN PROG.1 F-IMC Program F-IMC PROG.2 LCD DATA LCD DATA

AL-2050CS

1) Initial display



AL-2030/2040CS


22-14 ROM VER.MAIN PROG. 00.00

22-14 ROM VER.F-IMC PROG. 00.00

22-14 ROM VER.LCD DATA 00.00

AL-2050CS

1) Initial display

AL-2040CS

The count value is displayed in 3 digits X 2times repeatedly.

<Display example: 12345>22-16 DPLX CNT ***,***

012 → Blank → 345 → Blank → 0120.7s 0.3s 0.7s 1.0s 0.7s

AL-2050CS

1) Initial display

AL-2030/2040CS


22-17 COPIES CNT ***,***

AL-2050CS

1) Initial display

AL-2030/2040CS


22-18 PRT.CNT ***,***


22 19 Scanner mode counter display (AL-2040CS/2050CS only)

[Function]The scanner mode counter is displayed.

[Operation]

21 Scanner counter display [Function]The scanner counter is displayed.

[Operation]

22 SPF/RSPF JAM counter display

[Function]The SPF/RSPF JAM counter is displayed.

[Operation]

24 01 JAM total counter clear [Function]When [ENTER]/[START] key is pressed, the JAM total counter is cleared to 0 and "000,000" isdisplayed on the LCD/display.

[Operation]

04 SPF/RSPF counter clear [Function]When [ENTER]/[START] key is pressed, the SPF/RSPF counter value is cleared to 0 and"000,000" is displayed on the LCD/display.

[Operation]

05 Duplex counter clear (AL-2040CS/2050CS only)

[Function]When [ENTER]/[START] key is pressed, the duplex counter value is cleared to 0, and "000,000"is displayed on the LCD/display.

[Operation]

07 Drum counter clear [Function]When [ENTER]/[START] key is pressed, the drum counter value is cleared to 0, and "000,000"is displayed on the LCD/display.

[Operation]

Main code

Sub code


AL-2050CS

1) Initial display

AL-2040CS


22-19 S-MODE CNT ***,***

AL-2050CS

1) Initial display

AL-2030/2040CS


22-21 SCAN CNT ***,***

AL-2050CS

1) Initial display

AL-2030/2040CS


22-22 S JAM CNT ***,***

AL-2050CS

1) Initial display

AL-2030/2040CS


24-01 JAM TTL CLR.CLEARED 000,000

AL-2050CS

1) Initial display

AL-2030/2040CS


24-04 SPF CLR.CLEARED 000,000

AL-2050CS

1) Initial display

AL-2040CS


24-05 DPLX CLR.CLEARED 000,000

AL-2050CS

1) Initial display

AL-2030/2040CS


24-07 DRUM CLR.CLEARED 000,000


24 08 Copy counter clear [Function]When [ENTER]/[START] key is pressed, the copy counter value is cleared to 0, and "000,000" isdisplayed on the LCD/display.

[Operation]

09 Printer counter clear [Function]When [ENTER]/[START] key is pressed, the printer counter value is cleared to 0, and "000,000"is displayed on the LCD/display.

[Operation]

13 Scanner counter clear [Function]When [ENTER]/[START] key is pressed, the scanner counter value is cleared to 0, and "000,000" is displayed on the LCD/display.

[Operation]

14 SPF/RSPF JAM total counter clear

[Function]When [ENTER]/[START] key is pressed, the SPF/RSPF JAM total counter value is cleared to 0,and "000,000" is displayed on the LCD/display.

[Operation]

15 Scanner mode counter clear (AL-2040CS/2050CS only)

[Function]When [ENTER]/[START] key is pressed, the scanner mode counter value is cleared to 0, and"000,000" is displayed on the LCD/display.

[Operation]

25 01 Main motor operation check (Cooling fan motor rotation check)

[Function]When [ENTER]/[START] key is pressed, the main motor (and the duplex motor in the case of aduplex model) is operated for 30sec.

To reduce toner consumption, if the developing unit is installed, the developing bias, the maincharger, and the grid are also outputted.

In this case, laser discharge is required when stopping the motor, the polygon motor is alsooperated at the same time. Check for installation of the developing unit. If it is not installed, thehigh voltage above is not outputted and only the motor is rotated.

To check the developing bias, install the developing unit.

After completion of 30sec operation, the machine goes into the sub code entry standby mode.


Main code

Sub code


AL-2050CS

1) Initial display

AL-2030/2040CS


24-08 COPIES CLR.CLEARED 000,000

AL-2050CS

1) Initial display

AL-2030/2040CS


24-09 PRT.CLR.CLEARED 000,000

AL-2050CS

1) Initial display

AL-2030/2040CS


24-13 SCAN CLR.CLEARED 000,000

AL-2050CS

1) Initial display

AL-2030/2040CS


24-14 S JAM TTL CLR.CLEARED 000,000

AL-2050CS

1) Initial display

AL-2040CS


24-15 S-MODE CLR.CLEARED 000,000

1) Initial display

25-01 MAIN MOTOR CHKEXECUTING...


25 10 Polygon motor ON [Function]When [ENTER]/[START] key is pressed, the Bios is called to rotate the polygon motor for 30sec. After completion of 30sec operation, the operation is turned off with the Bios and the machinegoes into the sub code entry standby mode.


26 02 SPF/RSPF setup [Function]When this simulation is executed, the current set SPF/RSPF is displayed. Enter the code num-ber corresponding to the desired SPF/RSPF and press [ENTER]/[START] key to save the set-ting.

[Operation]

03 Second cassette setup [Function]When this simulation is executed, the current set second cassette is displayed. Enter the codenumber corresponding to the desired second cassette and press [ENTER]/[START] key to savethe setting.

[Operation]The operation is similar to simulation 26-02.

04 Machine duplex setup [Function]When this simulation is executed, the current set duplex is displayed. Enter the code numbercorresponding to the desired duplex and press [ENTER]/[START] key to save the setting.


06 Destination setup [Function]When this simulation is executed, the current set destination is displayed. Enter the code number corresponding to the desired destination and press [ENTER]/[START] key to save the setting.

* Code number 2 cannot be selected.


Main code

Sub code


1) Initial display

25-10 LSU CHKEXECUTING...

Code number SPF/RSPF Display item0 SPF NO SPF OFF1 SPF YES SPF ON2 RSPF YES RSPF ON

AL-2050CS

1) The current set value isdisplayed.




AL-2030/2040CS

1) Press [ ] [ ] key tochange the code number.

2) Press [START] key to fixthe code number.

26-02 SPF/RSPF1:SPF ON (0- 2)

26-02 SPF/RSPF0:SPF OFF (0- 2)

26-02 SPF/RSPF2:RSPF ON (0- 2)

26-02 SPF/RSPF2:RSPF ON (0- 2)

Code number Second cassette Display item0 Second cassette NO OFF1 Second cassette YES ON

* AL-2030: cannot be executed.

Code number Duplex Display item0 Duplex NO OFF1 Duplex YES* ON

Code number Destination Display item0 Inch series INCH1 EX Japan AB series AB2 Japan AB series –


26 07 Machine conditions check [Function]When this simulation is executed, the current machine setting is displayed.


20 Rear edge void setup [Function]When this simulation is executed, the current set rear edge void is displayed. Enter the codenumber corresponding to the desired rear edge void and press [ENTER]/[START] key to savethe setting.


30 CE mark support control ON/OFF

[Function]When this simulation is executed, the current set CE mark support control is displayed. Enterthe code number corresponding to the desired CE mark support control and press [ENTER]/[START] key to save the setting.


38 Cancel of stop at drum life over

[Function]When this simulation is executed, the current setup of the code number is displayed. Enter thecode number and press the PRINT switch to enable the setup.


39 Memory capacity check [Function]When the simulation is executed, the currently installed SDRAM of the main unit is displayed.


40 Polygon motor OFF time setup (Time required for turning OFF after completion of printing)

[Function]When this simulation is executed, the current setting is displayed. Enter the code number corre-sponding to the desired setting and press [ENTER]/[START] key to save the setting.


Main code

Sub code


CPM Copy quantity Remark20 CPM 20

1) The machine setting is displayed.

26-07 CPM20 CPM

Code number Setting Display item Remark0 Rear edge void NO OFF1 Rear edge void YES ON Default

Code number Setting Display item Remark0 CE mark support control OFF OFF Default (100V series)1 CE mark support control ON ON

Code number Setup0 Stop at drum life over * Default (AL model)1 Cancel of stop at drum life over

Code number Setting Remark8 8 MBYTE16 16 MBYTE

1) Memory capacity display

26-39 MEM.CHK8 MBYTE

Code number SettingDisplay item

RemarkAL-2050CS AL-2030/2040CS

0 0sec 0 SEC. 01 30sec 30 SEC. 30 Default2 60sec 60 SEC. 603 90sec 90 SEC. 90


26 42 Transfer ON timing control setup

[Function]


Main code

Sub code


AL-2030/2040CS

When this simulation is executed, the currently set code number is displayed.

Enter the code number and press the [START] key, and the setting will be changed. (For anynumber different from the following ones, the default time is automatically set.)

<Paper lead edge adjustment table>

* The default value, "11," of the transfer ON timing indicates "236msec passed from PSrelease."

* When set to "0," it is same as setting to the default, "11."

* The transfer ON timing can be adjusted to 236msec ± 2ms.

AL-2050CS

For the AL-2050CS, the adjustment can be made individually for each of the following modes.

<Paper lead edge adjustment table> is the same as that of the AL-2030/2040CS above.

<Front/back surface of paper rear edge adjustment table>

* The default "50" of the transfer OFF timing indicates "210msec passed from PPD1OFF."

* The transfer OFF timing can be adjusted to 210msec ± 2ms.

Code number Setting Code number Setting0 Default (236 msec) 11 Default (236 msec)1 –20 msec 12 +2 msec2 –18 msec 13 +4 msec3 –16 msec 14 +6 msec4 –14 msec 15 +8 msec5 –12 msec 16 +10 msec6 –10 msec 17 +12 msec7 –8 msec 18 +14 msec8 –6 msec 19 +16 msec9 –4 msec 20 +18 msec

10 –2 msec 21 +20 msec

Mode Display item Default Setting rangeFront surface paper lead edge F-REAR 11 0 - 21Front surface paper rear edge F-END 50 1 - 99Back surface paper lead edge B-REAR 11 0 - 21Back surface paper rear edge B-END 50 1 - 99

Code Setting Remark1 –98 msec

. . . . . .49 –2 msec50 0 msec Default51 +2 msec. . . . . .99 +98 msec

1) Initial display <Front surface lead edge setting>

2) [ ] [ ] key: Mode selection

3) [Numeric] key: Value entry

4) [ENTER]/[START] key: Settles the entered value. The display isshifted to the sub code input standbymenu.

26-42 TC ON TIMINGF-REAR 11( 0-21 )

26-42 TC ON TIMINGF-END 50( 1-99 )

26-42 TC ON TIMINGF-END 51( 1-99 )


26 43 Side void setup [Function]When this simulation is executed, the currently set code of the side void quantity is displayed(initial display), and the set data are saved. (Setting range: 0 – 10, Default: 4 (= One side2.0mm))

* When the adjustment value is increased by 1, the side void is changed as follows:Side void adjustment: The side void is increased by 0.5mm. (The side void of "Set value x0.5mm" is made.)


54 γ life correction setting [Function]Used to set the γ life correction.

When this simulation is executed, the current set code number is displayed.

Enter the desired code number and press [ENTER]/[START] key to save the setting. (Setting range: 0 – 1, default: 1)


62 Energy-save mode copy lamp setup

[Function]Used to set half-ON /OFF of the copy lamp in the pre-heat mode.

When this simulation is executed, the current set code number is displayed. Enter the desiredcode number and press [ENTER]/[START] key to save the setting.


30 01 Paper sensor status display [Function]The paper sensor status is displayed on the LCD/LED.

∗ Since the manual paper feed sensor is a single bypass sensor, its status is not displayed.∗ The width sensor is available only in the FAX models.


Main code

Sub code


Code Setting Remark0 0 mm1 0.5 mm2 1.0 mm3 1.5 mm4 2.0 mm Default5 2.5 mm6 3.0 mm7 3.5 mm8 4.0 mm9 4.5 mm

10 5.5 mm

Code number Setting Display item Remark0 OFF OFF1 ON ON Default

Code number Setting Display item Remark0 Copy lamp OFF OFF1 Copy lamp half-ON ON Default

SensorDisplay item (AL-2050CS)

Display lamp (AL-2030/2040CS)

Paper exit sensor POD Photoconductor cartridge replacement lampPaper entry sensor PPD1 Developer cartridge replacement lampDuplex sensor PPD2 JAM lamp No. 2 tray paper feed sensor PPD3 2nd cassette lamp New drum cartridge sensor DRST Zoom lamp

1) Initial display 2) When sensor ON

30-01 P-SENSOR 30-01 POD PD1 PD2PPD1 PPD2 PPD3 DRST


41 06 OC cover float detection level adjustment

[Function]When this simulation is executed, the current set value is displayed. When [ENTER]/[START]key is pressed, the mirror base unit moves to the SPF/RSPF scan position to acquire the OCcover float detection level.

When the mirror base unit returns to the home position, the acquired value is displayed.

If the adjustment is NG, the following message is displayed.

AL-2030/2040CS: Misfeed lamp lights up, and the 7seg display remains unchanged.

AL-2050CS: The LCD indicates "ERR."

Note that, this simulation must be executed with the OC cover closed.∗ If the value is 0, float detection is not performed in normal jobs.


07 OC cover float detection margin setting

[Function]For the number of pixels between black markers on the SPF/RSFP scanning position saved in"41-06: (OC cover float detection level adjustment)", if the number of pixels between the mark-ers when processing float detection is less than the number of pixels set with this simulation, itis judged as the float error.

When the set value of this simulation is "0," no float error occurs.

When this simulation is executed, the current set value is displayed.

Enter the adjustment value with [ ] [ ] key (or [Numeric] key for the AL-2050CS), and press[START] key. The setting is saved and the display is shifted to the sub code input standby menu. Setting range: 0 – 99 (Copes with margin 0 – 99 pixels.)

Default: 30 (30 pixels)


Main code

Sub code


1) Initial display

2) [ENTER/START] key

41-06 OC FLOAT LEVEL 0

41-06 OC FLOAT LEVELEXECUTING...

<Canceling - when [Clear]/[Clear All] key is pressed->

After canceling, the machine goes into the sub code entrystandby mode.

3) When the level is acquired:

3) When the level is not acquired:


41-06 OC FLOAT LEVEL **** OK

41-06 OC FLOAT LEVEL **** ERR


43 01 Fusing temperature setting (Normal copy)

[Function]Used to set the fusing temperature of 3rd or later sheet. (For 1st and 2nd sheets, SIM 43-14 isused.)

When this simulation is executed, the current set code number is displayed. Press [ ] [ ] key(or [Numeric] key for the AL-2050CS) to change the setting and press [ENTER]/[START] key tosave the setting into the EERPOM. The machine goes into the sub code entry standby mode.

The [Exposure mode selector] key (or [ ] [ ] key for the AL-2050CS) is used to select themode.

[Operation]

04 Fusing temperature setting in multi copy

[Function]For 20th sheet or later in multi copy, the fusing temperature is automatically changed from thetemperature set with simulation 43-1 to the temperature set with this simulation.

When this simulation is executed, the current set code number is displayed. Enter the codenumber and press [ENTER]/[START] key to change the setting.

∗ The cassette feed and the manual feed are controlled similarly.


Main code

Sub code


* The cassette feed and the manual feed are controlled similarly.

Code Set temperature (°C) Remark Code Set temperature (°C) Remark0 170 5 195 Default1 175 6 2002 180 7 2053 185 8 2104 190


Display item(AL-2030/2040CS)

Main cassette paper feed & 2nd cassette paper feed TRAY1 AE mode lamp Manual paper feed MFT TEXT mode lamp

AL-2050CS

1) Initial display <Main cassette paper feed& 2nd cassette paper feed setting>

2) [ ] [ ] key: Mode selection



Settles the entered value. The display isshifted to the sub code input standbymenu.

AL-2030/2040CS

1) Press [Exposure mode selector] key tochange the mode.

2) Press [ ] [ ] key to set the value.

3) Press [START] key to fix the code number.

43-01 FU TEMPTRAY1 6( 0-8 )

43-01 FU TEMPMFT 6( 0-8 )

43-01 FU TEMPMFT 6( 0-8 )

Code Set temperature (°C) Remark0 1651 1702 1753 1804 1855 1906 1957 200


Display lamp(AL-2030/2040CS)

Default

Main cassette paper feed & 2nd cassette paper feed

TRAY1 AE mode lamp 3

Manual paper feed MFT TEXT mode lamp 3Main cassette paper feed & 2nd cassette paper feed (small-size)

TRAY1 SH PHOTO mode lamp 1

Manual paper feed (small-size) MFT SH AE mode lampTEXT mode lamp

1


43 05 Fusing temperature setup in duplex copy (AL-2040CS/2050CS only)

[Function]In the case of duplex copy, the shift temperature set with this simulation is applied to the fusingtemperature.When this simulation is executed, the current set code number is displayed. Enter the desired code number and press [ENTER]/[START] key to save the setting.


14 Fusing start temperature setting

[Function]When this simulation is started, the currently set code number is displayed.Press [ ] [ ] key (or [Numeric] key or [ ] [ ] key for the AL-2050CS) to switch the setting,and press [ENTER]/[START] key to save it to the EEPROM. The machine goes to the sub codeentry standby mode.


Main code

Sub code


Code Shift temperature (°C) Remark0 ±0 Default1 –82 –63 –44 –25 ±06 +27 +48 +69 +8

Code Set temperature (°C) Remark0 1601 1652 1703 1754 1805 1856 1907 195 Default8 2009 20510 210


46 01 Copy density adjustment (300dpi)

[Function]Copy density is set for each mode.When this simulation is executed, the current se value is displayed in 2 digits (Default: 50).Change the set value and press [START] key to make a copy under the set value.When the set value is increased, the copy becomes darker. When the set value is decreased,the copy becomes lighter.In this case, only Exp.3 copy is made. When, however, the setting is made to make darker copy,Exp.1 and Exp.5 copies also become darker. When made to lighter copy, Exp1. and Exp.5 cop-ies become lighter, too.Press [Exposure mode selector] key (or [ ] [ ] key for the AL-2050CS) to switch the mode.The set value of the selected mode is displayed on the LCD/display. (Adjustment value: 1 – 99) The setting procedure of the magnification ratio is the same as that to copy operation.

[Operation]

02 Copy density adjustment (600dpi)

[Function]Copy density is set for each mode.When this simulation is executed, the current se value is displayed in 2 digits (Default: 50).Change the set value and press [START] key to make a copy under the set value.When the set value is increased, the copy becomes darker. When the set value is decreased,the copy becomes lighter.In this case, only Exp.3 copy is made. When, however, the setting is made to make darker copy,Exp.1 and Exp.5 copies also become darker. When made to lighter copy, Exp1. and Exp.5 cop-ies become lighter, too.Press [Exposure mode selector] key (or [ ] [ ] key for the AL-2050CS) to switch the mode.The set value of the selected mode is displayed on the LCD/display. (Adjustment value: 1 – 99)


Main code

Sub code



LED(AL-2050CS)


Default

AE mode (300dpi) AE COPY mode lamp AE mode lamp 50TEXT mode (300dpi) TEXT PRINT mode lamp TEXT mode lamp 50PHOTO mode PHOTO SCAN mode lamp PHOTO mode lamp 50TS mode (TEXT) (300dpi) TSTXT PRINT mode lamp

SCAN mode lampTEXT mode lampPHOTO mode lamp

50

TS mode (AE) (300dpi) TSAE COPY mode lampSCAN mode lamp

AE mode lampPHOTO mode lamp

50

AL-2050CS1) Initial display

2) [ ] key: Mode selection

2) [ ] key: Mode selection


4) [START] key: Fixing and printing value (No change on the LCD)

* Print is started in the set mode.

4) To fix the set value without printing, press[Enter] key.

* To cancel manual feed paper empty MSG,press any key.

* When performing the AE mode exposureadjustment, place the test chart on the docu-ment table so that the center area of 10cm isnot covered.

AL-2030/2040CS1) Press [Exposure mode selector] key to

change the mode.

2) Press [ ] [ ] key to set the value.

3) [START] Fixing and printing value

* Print is started in the set mode.

46-01 EXP.LEVEL 300AE 100% 50( 1-99)

46-01 EXP.LEVEL 300TSAE 100% 50( 1-99)

46-01 EXP.LEVEL 300TEXT 100% 50( 1-99)

46-01 EXP.LEVEL 300AE 100% 62( 1-99)

46-01 EXP.LEVEL 300AE 100% 62( 1-99)

46-01 EXP.LEVEL 300AE 100% 62( 1-99)


LED(AL-2050CS)


Default

AE mode (600dpi) AE COPY mode lamp AE mode lamp 50TEXT mode (600dpi) TEXT PRINT mode lamp TEXT mode lamp 50PHOTO mode PHOTO SCAN mode lamp PHOTO mode lamp 50TS mode (TEXT) (600dpi) TSTXT PRINT mode lamp


50



50


46 18 Image contrast adjustment (300dpi)

[Function]Contrast is set for each mode.When this simulation is executed, the current se value is displayed in 2 digits (Default: 50).Change the set value and press [START] key to make a copy under the set value.When the set value is increased, the contrast becomes higher. When the set value isdecreased, the contrast becomes lower.In this case, only Exp.3 copy is made. When, however, the setting is made to make higher con-trast, Exp.1 and Exp.5 copies also become in higher contrast. When made to a lower contrast,Exp1. and Exp.5 copies become lower contrast, too.Press [Exposure mode selector] key (or [ ] [ ] key for the AL-2050CS) to switch the mode.The set value of the selected mode is displayed on the LCD/display. (Adjustment value: 1 – 99)

* No density display on LCD/display.


19 Exposure mode setup [Function]<γ table setting>

When this simulation is executed, the code number of the current set gamma table is displayed.(Default: 2)Enter the code number corresponding to the desired gamma table, and press [Exposure modeselector] key (or [ ] [ ] key for the AL-2050CS) to change the mode and write into theEEPROM.

<AE operation mode>

When setting the γ table, press [Exposure mode selector] key (or [ ] key for the AL-2050CS)to change to the AE operation mode, and the current set code number of the AE operationmode is displayed. (Default: 0)Enter the code number corresponding to the desired AE operation mode and press [Exposuremode selector] key (or [ ] [ ] key for the AL-2050CS) to change the mode and write intothe EEPROM.

<PHOTO image process setting>

When [Exposure mode selector] key (or [ ] key for the AL-2050CS) is pressed in AE opera-tion mode setting, the mode is changed to the PHOTO image process setting and the codenumber of the current set PHOTO image process setting is displayed. (Default: 1)Enter the code number corresponding to the desired PHOTO image process setting and press[Exposure mode selector] key (or [ ] [ ] key for the AL-2050CS) to change the mode andwrite into the EEPROM.


Main code

Sub code



LED(AL-2050CS)


Default

AE mode (300dpi) AE COPY mode lamp AE mode lamp 50TEXT mode (300dpi) TEXT PRINT mode lamp TEXT mode lamp 50PHOTO mode PHOTO SCAN mode lamp PHOTO mode lamp 50TS mode (TEXT) (300dpi)

TSTXT PRINT mode lampSCAN mode lamp

TEXT mode lampPHOTO mode lamp

50

TS mode (AE) (300dpi)

TSAE COPY mode lampSCAN mode lamp


50



Code number

Setting content Remark

γ GAMMA OFF1

Image quality priority mode

2Toner consumption priority mode

Default

AE AE AE 0 Lead edge stop Default1 Real time process

PHOTO PHOTO PHOTO1 Error diffusion process Default2 Dither process


46 20 SPF/RSPF exposure correction

[Function]Used to adjust the exposure correction amount in the SPF/RSPF mode. The adjustment ismade by adjusting Vref voltage variation for the OC mode.

When this simulation is executed, the current set value is displayed in 2 digits (Default: 50).Change the set value and press [START] key to save the setting and make a copy.

When the set value is increased, copy becomes darker. When the set value is decreased, copybecomes lighter. (Adjustment range: 1 – 99)


29 Image contrast adjustment (600dpi)

[Function]Contrast is set for each mode.

When this simulation is executed, the current se value is displayed in 2 digits (Default: 50).

Change the set value and press [START] key to make a copy under the set value.

When the set value is increased, the contrast becomes higher. When the set value isdecreased, the contrast becomes lower.

In this case, only Exp.3 copy is made. When, however, the setting is made to make higher con-trast, Exp.1 and Exp.5 copies also become in higher contrast. When made to a lower contrast,Exp1. and Exp.5 copies become lower contrast, too.

Press [Exposure mode selector] key (or [ ] [ ] key for the AL-2050CS) to switch the mode.The set value of the selected mode is displayed on the LCD/display. (Adjustment value: 1 – 99)

* No density display on LCD/display.


30 AE limit adjustment [Function]Used to set the limit value in AE and AE (toner save).Change the setting and press [ENTER]/[START] key to write the setting into the EEPROM. Themachine goes into the sub code entry standby mode.By pressing [Exposure mode selector] key (or [ ] [ ] key for the AL-2050CS), setting ischanged. (Setting range: 0 – 31, Default: 0)

<Remark>

When simulation 26-06 (Destination setting) or simulation 46-19 Auto Exposure mode ischanged, the setting of this simulation is also changed to the default in connection.


Main code

Sub code


ModeDisplay item(AL-2050CS)


Default Remark

RSPF/SPF SPF TEXT mode lamp 50


LED(AL-2050CS)


Default

AE mode (600dpi) AE COPY mode lamp AE mode lamp 50TEXT mode (600dpi) TEXT PRINT mode lamp TEXT mode lamp 50PHOTO mode PHOTO SCAN mode lamp PHOTO mode lamp 50TS mode (TEXT) (600dpi)

TSTXT PRINT mode lampSCAN mode lamp

TEXT mode lampPHOTO mode lamp

50



50

ModeDisplay item(AL-2050CS)


Remark

Limit value for AE AE AE mode lampLimit value for AE (toner save) TEXT TEXT mode lamp


46 31 Image sharpness adjustment

[Function]Used to adjust sharpening/blurring of image in each mode.

When this simulation is executed, warm-up and shading are performed and the current setvalue is displayed. (Default: 1)Change the set value and press [START] key to make a copy under the set conditions.To change the mode, press [Exposure mode selector] key (or [ ] [ ] key for the AL-2050CS). The code number of the selected mode is dip0slayed on the LCD/display.


32 Copier color reproduction setup

[Function]Used to set color reproduction in each mode. Colors easy to be copied and colors difficult to becopied can be switched.

* This setting has virtually no effect on black-and-white documents.

When this simulation is executed, warm-up and shading are performed and the current setvalue is displayed. (Default: 0)Press [START] key to make a copy under the set conditions . At that time, color components arechanged for used in copying.To change the mode, press [Exposure mode selector] key (or [ ] [ ] key for the AL-2050CS). The code number of the selected mode is dip0slayed on the LCD/display.


Main code

Sub code


Image quality Setting No RemarkBlurring 0

Standard 1 DefaultSharpening 2


LED(AL-2050CS)


Default setting

AE mode AE COPY mode lamp AE mode lamp 1TEXT mode TEXT PRINT mode lamp TEXT mode lamp 1PHOTO mode PHOTO SCAN mode lamp PHOTO mode lamp 1TS mode (TEXT) TSTXT PRINT mode lamp


1

TS mode (AE) TSAE COPY mode lampSCAN mode lamp

AE mode lamp PHOTO mode lamp

1

Set value Colors easy to be copied Colors difficult to be copied0 Purple, Blue, Red Yellow, Green, Water blue1 Water blue, Green, Blue Purple, Red, Yellow2 Yellow, Red, Green Blue, Water blue, Purple

Specification component Setting No RemarkGreen 0 DefaultRed 1Blue 2


LED(AL-2050CS)


Default setting

AE mode (including TS)

AE COPY mode lamp AE mode lamp 0

TEXT mode (including TS)

TEXT PRINT mode lamp TEXT mode lamp 0

PHOTO mode PHOTO SCAN mode lamp PHOTO mode lamp 0


48 01 Front/rear (main scanning) direction and scan (sub scanning) direction magnification ratio adjustment

[Function]Used to adjust the magnification ratio in the main scan (front/rear) direction and sub scan direc-tion.

Enter the adjustment value with [ ] [ ] key (or [Numeric] key for the AL-2050CS). Press[START] key to save the set value and make a copy. (When the adjustment value is increasedby 1, the magnification ratio is increased by 0.1%.)

The adjustment mode can be changed by pressing [Exposure mode selector] key (or [ ] [ ]key for the AL-2050CS). (Adjustment range: 1 – 99, Default: 50)


05 SPF/RSPF mode sub scan direction magnification ratio in copying

[Function]Used to display the current SPF/RSPF mode sub scan direction magnification ratio on the LCD/display.

When [START] key is pressed, the entered data is acquired and saved into the EEPROM, and acopy is made. (When the set value is increased by 1, the magnification ratio is increased by0.1%.)


When adjusting the RSPF, the mode is set to "Duplex → Single," single copies of two sheets areperformed.

For printing, regardless of the density mode and the density level,

Density mode = MANUALDensity level = 3

* When there is no document in SPF/RSPF, copy is inhibited.


Main code

Sub code



LED(AL-2050CS)


Default value

Main scan direction magnification ratio

F-R PRINT mode lamp TEXT mode lamp 50


SCAN SCAN mode lamp PHOTO mode lamp 50

ModeInitial value of duplex setting

Display item (AL-2050CS)

LED(AL-2050CS)


Default

Sub scan magnification ratio adjustment on the front surface of SPF/RSPF document

S-S SIDE1 COPY mode lamp

AE mode lamp

50

Sub scan magnification ratio adjustment on the back surface of RSPF document (AL-2050CS only)

D-S SIDE2 PRINT mode lamp

— 50


49 01 Flash ROM program writing mode

[Function]When this simulation is executed, "d" is displayed on the display (or "DOWNLOAD MODE" isdisplayed on the LCD for the AL-2050CS), the machine goes into the program writing modefrom PC to Flash ROM.

Use the writing tool on the PC and write the program.

During writing, the display shows as follows:

After completion of download, turn OFF/ON the power to reset.

In case of an error in download, the following message is displayed on the LCD. (AL-2050CS only)

To enter the download mode, there is a method to use key operations as well as to use a simu-lation. With the power OFF, press and hold [Clear All] key + [ ] key, turn on the power.


Main code

Sub code


* "∗" in an error display indicates the error position.

StatusAL-2050CS AL-2030/2040CS

RemarkDisplay item Display

Pre-heat lamp

Ready lamp

Download data receiving RECEIVING "d" ON ON OFFLoader function transfer LOADER COPYING AL-2050CS onlyDate delete start FLASH ERASE "d" ON OFF ONData write (Boot section) BOOT WRITING "d" ON Blink OFFData write (Program section)

PROGRAM WRITING "d" ON Blink Blink

Data write (EEPROM) E2PROM WRITING AL-2050CS onlyData write (LCD) LCD DATE WRITING AL-2050CS onlyDuring SUM CHECK FLASH ROM SUM

CHECK"d" ON ON ON

During BOOT SUM CHECK

BOOT SUM CHECK AL-2050CS only

During EEPROM SUM CHECK

EEPROM SUM CHECK AL-2050CS only

Download complete DOWNLOAD COMPLETE!

"0FF" ON OFF OFF

Error state "E ∗" ON OFF OFF AL-2030/2040CS only

1 Data reception error 6 Sum check (Loader section)2 Loader function transfer 7 Sum check (Boot section)3 FLASH ROM delete 8 Sum check (Program section)4 FLASH ROM writing (Boot section) 9 Sum check (EEPROM section)5 FLASH ROM writing (Program section) 10 Data error

Error status Display itemPC data receiving E-01 PC TRANSLoader function transfer E-02 LOADER COPYFLASH ROM delete E-03 FLASH ERASEBoot section FLASH ROM write E-04 BOOT WRITEProgram section FLASH ROM write E-05 PROGRAM WRITELoader section SUM CHECK E-06 LOADER SUMBoot section SUM CHECK E-07 BOOT SUMProgram section SUM CHECK E-08 PROGRAM SUME2PROM SUM CHECK E-09 E2PROM SUME2PROM write E-10 E2PROM WRITEE2PROM read Verify E-11 E2PROM READE2PROM collating Verify E-12 E2PROM COLLATEBoot section lens check E-13 BOOT LENGTHProgram section lens check E-14 PROGRAM LENGTHE2PROM lens check E-15 E2PROM LENGTHTotal data size check E-16 DATE SIZEIMC communication error E-17 IMC TRANSIMC FRASH ROM write E-18 IMC FLASH WRITELCD section lens check E-19 LCD DATE LENGTHLCD section FLASH ROM write E-20 LCD DATE WRITELCD section SUM CHECK E-21 LCD DATE SUM

1) Initial display

DOWNLOAD MODE


50 01 Lead edge image position [Function]Used to adjust the copy image position and the lead edge void amount on copy paper. Theadjustment is made by adjusting the image scan start position at 100% and the print start posi-tion (resist roller ON timing). When this simulation is executed, the current set value is displayedin 2 digits. (Center value: 50)

When [Exposure mode selector] key (or [ ] [ ] key for the AL-2050CS) is pressed, the set-ting mode and the display are changed.

Enter the adjustment value and press [START] key to save the set value and make a copy.

When the adjustment is made by the main cassette paper feed, the adjustment values of all thepaper feed ports become the same. (When the set value is increased by 1, shift is made by0.1mm.)

(*): Support for the installation models. For non-installation models, skip.

* When printing with the manual paper feed tray, use paper of the letter size.

* When paper is discharged, the shifter is operated.

[Adjustment procedure]1) Set the print start position (AE lamp ON) (A), the lead edge void amount (TEXT lamp ON)

(B), and the scan start position (PHOTO lamp ON) (C) to 0, and make a copy of a scale at100%. (AL-2030/2040CS)

For the AL-2050CS, the following LED’s are lighted:

• AE lamp/COPY mode lamp: (A)

• TEXT lamp/PRINT mode lamp: (B)

• PHOTO lamp/SCAN mode lamp: (C)

2) Measure the image loss (Rmm) of the scale.

Set C = 10 x R (mm). (Example: Set to 40.)

When the value of C is increased by 10, the image loss is decreased by 1mm. (Default: 50)

3) Measure the distance (Hmm) from the paper lead edge to the image print start position.

Set A = 10 x H (mm). (Example: Set to 50.)

When the value of A is increased by 10, the image lead edge is moved to the paper leadedge by 1mm. (Default: 50).

4) Set the lead edge void amount to B = 50 (2.5mm). (Default: 50)

When the value of B is increased by10, the void is extended by about0.1mm. (For 25 or less, however, thevoid amount is regarded as 0.)

∗ The SPF/RSPF adjustment is made by adjusting the SPF/RSPF image scan start position after OC adjustment.


Main code

Sub code



LED(AL-2050CS)


Default

Print start position (Main cassette paper feed)


AE mode lampMain cassette lamp

50

(*) Print start position (2nd cassette paper feed)


AE mode lamp2nd cassette lamp

50



AE mode lampManual feed lamp

50

Image lead edge void amount

DEN-A PRINT mode lampMain cassette lamp

TEXT mode lampMain cassette lamp

50

Image scan start position

RRC-A SCAN mode lampMain cassette lamp

PHOTO mode lampMain cassette lamp

50

Image rear edge void amount (Cassette paper feed)

DEN-B COPY mode lampPRINT mode lampSCAN mode lampMain cassette lamp

AE mode lampTEXT mode lampPHOTO mode lampMain cassette lamp

50

Image rear edge void amount (Manual paper feed)

RRC-B COPY mode lampPRINT mode lampManual paper feed lamp

— 50

5mm

10mm

Distance from the paper lead edge to the image lead edge, H = 5mm

Image loss, R = 4mm

(Example)


50 06 Copy lead edge position adjustment (SPF/RSPF)

[Function]Used to adjust the SPF/RSPF copy lead edge.

When the adjustment value of the document scan position adjustment is increased by 1, thescan start timing is advanced by 0.1mm.

The print result is shifted to the opposite direction of the scan start position.


When scanning a back surface of document, the mode must be changed to operate the SPF/RSPF by pressing [2-SIDED COPY] key.

∗ When there is no document in the SPF/RSPF, copy is inhibited.∗ When paper is discharged, the shifter is operated.


10 Center offset adjustment [Function]Used to adjust the center offset position of copy images on copy paper and that in scanningdocument.When this simulation is executed, the current set value is displayed.Enter the adjustment value and press [START] key to save the setting and make a copy. (Whenthe set value is changed by 1, the center is shifted by 0.1mm.)When the adjustment value is increased, the center is shifted to right. When decreased, thecenter is shifted to left.The modes can be selected by pressing [Exposure mode selector] key (or [ ] [ ] key for theAL-2050CS).When the set value is changed largely, the area outside the shading area may be scanned tocause black streaks on the edges. When the SPF/RSPF is used, select the mode for use of theSPF/RSPF by [2-SIDED COPY] key.


(**): For Simplex models, skip.* When printing with the manual paper feed tray, use paper of the letter size.

* In the 2nd print center offset adjustment, print is made forcibly as 1to2/Short Edge from OCregardless of duplex setting.



Main code

Sub code




LED(AL-2050CS)


Default

Front surface document scan position adjustment

S-S SIDE1 COPY mode lamp

AE mode lamp

50

Back surface document scan position adjustment (AL-2050CS only)

D-S SIDE2 PRINT mode lamp

— 50

Rear edge void adjustment (RSPF)

S-S END SCAN mode lamp

PHOTO mode lamp

50


LED(AL-2050CS)


Default

Print center offset (Main cassette paper feed)



50

(*) Print center offset (2nd cassette paper feed)



50

Print center offset (Manual paper feed)


AE mode lampManual paper feed lamp

50

(**) 2nd print center offset (Main cassette paper feed)

SIDE2 PRINT mode lampMain cassette lamp

TEXT mode lampMain cassette lamp

50


50 12 Document off-center adjustment

[Function]Used to adjust document scan off-center adjustment.The adjustment modes can be selected by pressing [Exposure mode selector] key (or [ ][ ] key for the AL-2050CS). (Adjustment range: 1 – 99, Default: 50)

When the adjustment value is increased, the print result is shifted to left.



18 Memory reverse position adjustment in duplex copy (AL-2040CS/2050CS only)

[Function]When this simulation is executed, the current set correction value is displayed.

Enter the correction value and press [START] key to save the entered correction value. (Correc-tion value range; 1 – 99, Default: 50)

For S-D mode front surface print and print of even paged in D-S mode, reverse memory copyoperation is performed from the rear edge of documents.

When, therefore, the print position adjustment of output images is required, adjust as follows:

In the reverse memory coping, when the document scan is made in the arrow direction, the out-put image is printed from the rear edge of scan image.

When, therefore, the print lead edge is shifted, set the reference chart so that the referenceposition is on the rear edge, and use this simulation to adjust the set value so that the print leadedge is matched.

Since printing is made from the image data most lately stored in memory to the lead edge datafrom the print start position, the image lead edge adjustment is made by changing the end dataposition stored in memory by the set value of this simulation.

Since it is performed by changing the scan end position, the image position adjustment is madeby changing the scan end position and the end data stored in memory.

The adjustment modes can be selected by pressing [Exposure mode selector] key (or [ ][ ] key for the AL-2050CS)

* The initial value of duplex setting is "1to2/Long Edge" for the duplex model, or "2to1" for thesimplex model.

∗ When paper is discharged, the shifter is operated.


Main code

Sub code




LED(AL-2050CS)

Display lamp (AL-2030/2040CS)

Default

Platen document scan S-S OC COPY mode lamp

AE mode lamp

50

SPF document front scan

S-S SPF PRINT mode lamp

TEXT mode lamp

50

RSPF document back scan (AL-2050CS only)

D-S RSPF SCAN mode lamp

— 50



LED(AL-2050CS)


Default

OC memory reverse output position

S-D OC COPY mode lamp

AE mode lamp 50

SPF/RSPF memory reverse output position

D-S SPF PRINT mode lamp

TEXT mode lamp

50

Document transport direction Document transport directionScan lead edge Print lead edge

Lead edge void (1)Print start position

Scan end position(Default: Scan cut by void (1)) Rear edge void

Print rear edgeScan direction Scan rear edge


50 19 Duplex copy rear edge void adjustment (AL-2040CS/2050CS only)

[Function]Used to adjust the rear edge void amount in duplex copy.

When this simulation is executed, the current set value is displayed in 2 digits. (Center value:50.) The adjustment modes can be selected by pressing [Exposure mode selector] key (or [ ][ ] key for the AL-2050CS). (Adjustment range; 1 – 99)

Enter the adjustment value and press [START] key to save the set value and make a copy. (Thepaper information is cleared for every copy.)

When the set value is increased by 1, the void amount is increased by about 0.1mm.

* The initial value for duplex setting is "1to2/Short Edge" for the OC setting, or "2to2" for theRSPF setting.

∗ When paper is discharged, the shifter is operated.


51 02 Resist quantity adjustment [Function]Used to adjust the contact pressure of the main unit resist roller and the SPF/RSPF resist rolleronto paper. When this simulation is executed, the current set value is displayed.

The adjustment modes can be selected by pressing [Exposure mode selector] key (or [ ][ ] key for the AL-2050CS).

Enter the adjustment value with [ ] [ ] key (or [Numeric] key for the AL-2050CS) and press[START] key to save the set value and make a copy.



Main code

Sub code



LED(AL-2050CS)

Display lamp

(AL-2030/2040CS)Default

Paper rear edge void amount

DEN-B PRINT mode lamp TEXT mode lamp 50

Print start position (Duplex back surface)

RRC-D SCAN mode lamp PHOTO mode lamp 50


LED(AL-2050CS)


Default

Main cassette paper feed



50

(*) 2nd cassette paper feed



50

Manual paper feed MFT COPY mode lampManual paper feed lamp

AE mode lampManual paper feed lamp

50

RSPF document paper feed (Front surface) (AL-2050CS only)

SIDE1 COPY mode lampPRINT mode lampSCAN mode lampMain cassette lamp

— 50

RSPF document paper feed (Back surface) (AL-2050CS only)

SIDE2 COPY mode lampPRINT mode lampMain cassette lamp

— 50

(*) Duplex back surface

DUP-2 PRINT mode lampSCAN mode lampMain cassette lamp

TEXT mode lampPHOTO mode lampMain cassette lamp

50


53 08 SPF/RSPF scan position automatic adjustment

[Function]Place a A4 paper (white chart) so that it covers the SPF/RSPF scan glass and the OC glasstogether, and close the SPF/RSPF.

When this simulation is executed, the current adjustment value is displayed as the initial display.

* Default is 1. Adjustment range is 1 – 99. Adjustment unit 1 = about 0.127mm

* If the values are kept as the default values, SPF/RSPF scan is not performed properly. Thefront area of the proper scan position may be scanned.

In case of AUTO, press [START] key, and the mirror unit scans from the home position to theSPF/RSPF scan position with the adjustment value displayed. The SPF/RSPF glass cover edgeposition is calculated from the difference between the SPF/RSPF glass cover edge and the OCside document glass CCD output level. If the adjustment is normal, the adjusted value is dis-played. If abnormal, the error LED lights up with the current set value displayed.

During the error LED is lighted, when [START] key is pressed again, execution is performedagain.

[Operation]The operation is similar to simulation 46-01. (In MANUAL)

OK/ERR display in AUTO

61 03 Polygon motor check (HSYNC output check)

[Function]When [ENTER]/[START] key is pressed, HSYNC is performed and the polygon motor is rotated for 30sec.At that time, the ZOOM lamp (or the COPY mode lamp for the AL-2050CS) is lighted for100msec every time when HSYNC is detected.


63 01 Shading check [Function]Used to display the detection level of white plate for shading.

When [ENTER]/[START] key is pressed, the mirror base unit moves to the white plate for shad-ing and the copy lamp is lighted.

When the light quantity is stabilized, revision is made for every second, and the level of onepixel at the center of CCD which is not corrected is detected and the value is displayed in deci-mal values on the LCD/display. (3 digits)


Main code

Sub code



LED(AL-2050CS)

Display lamp

(AL-2030/2040CS)Default

SPF/RSPF scan position auto adjustment

AUTO COPY mode lamp AE mode lamp 1

SPF/RSPF scan position manual adjustment

MANU PRINT mode lamp TEXT mode lamp 1

<When OK> <When ERR>

53-08 SPF AUTOAUTO 100% ** OK

53-08 SPF AUTOAUTO 100% ** ERR

1) Initial display

61-03 LSU CHKEXECUTING...

1) Initial display

63-01 SHADING CHKEXECUTING... 000


63 02 Black level automatic correction

[Function]Used to acquire the black level target value used for the black level adjustment of white balance.

When this simulation is executed, the current correction value is displayed in 3 digits of 12bithexadecimal number.

Place the gray gradation chart (UKOG-0162FCZZ) used as the correction document so that thedensity 10 (black side) comes on the left side and that the chart is upside down at the center ofthe plate left center.

When [ENTER]/[START] key is pressed, the mirror base unit scans the chart and calculates thecorrection value.

After completion of correction, the corrected value is displayed on the LCD/display.

* Default: 0

* If the value is set to the default, operation is made with 0x60.


12 Light quantity stabilization wait time setting

[Function]Used to set the wait time before entering the light quantity level stable evaluation process in thelight quantity stable process of white balance. (Note: The light quantity stable level in the previ-ous light quantity stable state is used as the target. When the light quantity level reaches thetarget during the wait time, the set time of this simulation is ignored and the operation enters thestable evaluation process.)

When this simulation is executed, the currently set value is displayed.Enter the adjustment value with [ ] [ ] key (or [Numeric] key for the AL-2050CS) and press [START] key. The entered value is stored and the machine goes into the sub code entry standby mode.Setting range: 0 – 99 (Complying with the light quantity stable wait time of 0 – 99sec.)

Default: 15 (15sec)


13 Light quantity stabilization band setting

[Function]When the difference between the maximum and the minimum values of the light quantity levelsampled for 3.2sec in the cycle of 100msec in the white balance light quantity stable process iswithin the range set with this simulation, it is judged as the light quantity is stable. (Note: Themagnification ratio of the AFE gain setting is automatically reflected on the stable width.)

When this simulation is executed, the currently set value is displayed.Enter the adjustment value with [ ] [ ] key (or [Numeric] key for the AL-2050CS) and press [START] key. The entered value is stored and the machine goes into the sub code entry standby mode.Setting range: 1 – 99 (Light quantity stable width: Complying with 1 – 99 in 4095 gradations.)

Default: 16


Main code

Sub code


Chart back surface

10

1) Initial display

2) [ENTER/START] key: Correction start

63-02 BLACK LEVEL 000

63-02 BLACK LEVELEXECUTING...

<During canceling - When [Clear]/[Clear All] key ispressed->

After canceling, the machine goes into the subcode entry standby mode.

3) After execution

3) In case of an error


63-02 BLACK LEVEL *** OK

63-02 BLACK LEVEL *** ERR


5. Trouble codesA. Trouble codes list B. Details of trouble codes

64 01 Self print [Function]The status of the optical section is ignored and printing of one page is made. Also when theprint command is received from the host, printing is made.

When this simulation is executed, warm-up is performed and the ready lamp is lighted. (Since,however, the scanner is disabled, initializing is not made.)

Enter the code number and press [ENTER]/[START] key to start paper feed from the selectedcassette and print in the selected pattern.

* For 4 – 99, flip.


67 50 USB receive speed adjustment (USB1.1) (AL-2030/AL-2040CS only)

Used to set the limitation on the print data receive speed of USB2.0 (Full speed) port (USB porton the machine).

→ When print images from USB2.0 (Full speed) port are disturbed, change the setting and tryagain.

When this simulation is executed, the currently set code number is displayed.

Enter the code number corresponding to the adjustment value, and press [START] key tochange the setting.

Main code

Sub code


Code number Pattern Display item0 1by2 1 BY 21 Grid pattern CHECK2 White paper WHITE3 Black background BLACK

Code number Setting Speed1 FAST ↑ Fast2 NORMAL13 NORMAL24 SLOW ↓ Slow

Main code

Sub code

Details of trouble

E1 00 IMC communication trouble10 IMC trouble13 IMC flash ROM error81 IMC communication interface error (Parity)82 IMC communication interface error (Overrun)84 IMC communication interface error (Framing)

E7 01 Duplex model memory setup error, memory not-detected error

02 LSU trouble10 Shading trouble (Black correction)11 Shading trouble (White correction)16 Abnormal laser output

F5 02 Copy lamp lighting abnormalityH2 00 Thermistor openH3 00 Heat roller high temperature detectionH4 00 Heat roller low temperature detectionL1 00 Feeding is not completed within the specified time

after starting feeding. (The scan head locking switch is locked)

L3 00 Scanner return troubleL4 01 Main motor lock detection

32 Exhaust fan motor lock detection troubleL6 10 Polygon motor lock detectionU2 04 EEPROM read/write error (Serial communication

error)11 Counter check sum error (EEPROM)

Main code

Sub code

Details of trouble

E1 00 Content IMC communication troubleDetail An abnormality occurs in communication

between the CPU and the IMC.Cause IMC abnormality

IMC memory defect/data abnormalityCheck and remedy

Replace the MCU PWB with new one.

10 Content IMC troubleDetail An abnormality occurs in the IMC.Cause USB chip error/CODEC error on the IMC.Check and remedy

Replace the MCU PWB with a new one.

13 Content IMC flash ROM errorDetail An abnormality occurs in the IMC flash

ROM.Cause IMC abnormalityCheck and remedy

Replace the MCU PWB with a new one.If downloading of the program is abnormally terminated, it may cause an error. Download the program again to avoid this.

81 Content IMC communication interface error (Parity)Detail A parity error occurs in communication

between the CPU and the IMC.Cause IMC abnormality

IMC memory defect/data abnormalityCheck and remedy



E1 82 Content IMC communication interface error (Overrun)

Detail An overrun error occurs in communication between the CPU and the IMC.

Cause IMC abnormalityIMC memory defect/data abnormality.

Check and remedy


84 Content IMC communication interface error (Framing)

Detail A framing error occurs in communication between the CPU and the IMC.

Cause IMC abnormalityIMC memory defect/data abnormality.

Check and remedy


E7 01 Content Duplex model memory setup error, memory not-detected error

Detail The memory is not set properly or the memory capacity is not set to the duplex setup (6M).

Check and remedy

Set SIM 26-39 code number to 2.

02 Content LSU troubleDetail The BD signal from the LSU cannot be

detected in a certain cycle. (Always OFF or always ON)

Cause LSU connector or LSU harness defect or disconnectionPolygon motor rotation abnormalityLaser beams are not generated.MCU PWB abnormality.

Check and remedy

Check connection of the LSU connector.Execute SIM 61-03 to check the LSU operations.Check that the polygon motor rotates normally.Check that the laser emitting diode generates laser beams.Replace the LSU unit.Replace the MCU PWB.

10 Content Shading trouble (Black correction)Detail The CCD black scan level is abnormal when

the shading.Cause Improper connection of the CCD unit flat

cableCCD unit abnormalityMCU PWB abnormality

Check and remedy

Check connection of the CCD unit flat cable.Check the CCD unit.

Main code

Sub code

Details of trouble

E7 11 Content Shading trouble (White correction)Detail The CCD white scan level is abnormal when

the shading.Cause Improper connection of the CCD unit flat

cableDirt on the mirror, the lens, and the reference white plateCopy lamp lighting abnormalityCCD unit abnormalityMCU PWB abnormality(When occurred in the SPF/RSPF scan position.)Improper installation of the mirror unit

Check and remedy

Clean the mirror, lens, and the reference white plate.Check the light quantity and lighting status of the copy lamp (SIM 05-03).Check the MCU PWB.

16 Content Abnormal laser outputDetail When the laser output is stopped, HSYNC is

detected.Cause Laser abnormality

MCU PWB abnormality.Check and remedy

Check the laser emitting diode operation.Replace the MCU PWB.

F5 02 Content Copy lamp lighting abnormalityDetail The copy lamp does not turn on.Cause Copy lamp abnormality

Copy lamp harness abnormalityCCD PWB harness abnormality.

Check and remedy

Use SIM 5-3 to check the copy lamp operations.When the copy lamp lights up.Check the harness and the connector between the CCD unit and the MCU PWB.When the copy lamp does not light up.Check the harness and the connector between the copy lamp unit and the MCU PWB.Replace the copy lamp unit.Replace the MCU PWB.

H2 00 Content Thermistor openDetail The thermistor is open.

The fusing unit is not installed.Cause Thermistor abnormality

Control PWB abnormalityFusing section connector disconnectionThe fusing unit is not installed.

Check and remedy

Check the harness and the connector between the thermistor and the PWB.Use SIM 14 to clear the self diagnostic display.

Main code

Sub code

Details of trouble


H3 00 Content Heat roller high temperature detectionDetail The fusing temperature exceeds 240°C.Cause Thermistor abnormality

Control PWB abnormalityFusing section connector disconnection.

Check and remedy

Use SIM 5-02 to check the heater lamp blinking operation.When the lamp blinks normally.Check the thermistor and its harness.Check the thermistor input circuit on the control PWB.When the lamp keeps ON.Check the power PWB and the lamp control circuit on the MCU PWB.Use SIM 14 to clear the self diagnostic display.

H4 00 Content Heat roller low temperature detectionDetail 1) When the target temperature (165°C) is

not reached in 55 sec after starting warming-up.

2) When the temperature below 100°C is detected for 300ms under the ready print state.

∗ "Starting warming-up" means not only that in power supply but also reset that in reset from shut-off and in side door close. (The timing of generating H4 is not limited to that in power supply.)

Cause Thermistor abnormalityHeater lamp abnormalityThermostat abnormalityControl PWB abnormality

Check and remedy

Use SIM 5-02 to check the heater lamp blinking operation.When the lamp blinks normally.Check the thermistor and its harness.Check the thermistor input circuit on the control PWB.When the lamp does not light up.Check for disconnection of the heater lamp and the thermostat. Check the interlock switch.Check the power PWB and the lamp control circuit on the MCU PWB.Use SIM 14 to clear the self diagnostic display.

Main code

Sub code

Details of trouble

L1 00 Content Feeding is not completed within the specified time after starting feeding. (The scan head locking switch is locked)

Detail The white area and the black marking on the shading plate are used to obtain the difference in the CCD level values for judgment of lock. When the difference in the levels of which and black is small, it is judged that the black mark could not be scanned by lock and the trouble code "L1" is displayed.

Cause The scan head is locked by the lock switch.Mirror unit abnormalityThe scanner wire is disconnected.The origin detection sensor abnormalityMirror motor harness abnormality

Check and remedy

Check to confirm that the scan head lock switch is released.Use SIM 1-1 to check the mirror reciprocating operations.When the mirror does not feed.Check for disconnection of the scanner wire.Check the harness and the connector between the mirror motor and the MCU PWB.Replace the mirror unit.Replace the MCU PWB.When the mirror does feed.Use SIM 1-2 to check the mirror home position sensor.

L3 00 Content Scanner return troubleDetail When the mirror base is returned for the

specified time (6 sec) in mirror initializing after turning on the power, the mirror home position sensor (MHPS) does not turn ON. Or when the mirror base is returned for the specified time (about 6 sec) after start of copy return, the mirror home position sensor (MHPS) does not turn ON.

Cause Mirror unit abnormalityScanner wire disconnectionOrigin detection sensor abnormalityMirror motor harness abnormality

Check and remedy

Use SIM 1-1 to check the mirror reciprocating operations.When the mirror does not return.Check for disconnection of the scanner wire.Check the harness and the connector between the mirror motor and the MCU PWB.Replace the mirror unit.Replace the MCU PWB.When the mirror does feed.Use SIM 1-2 to check the mirror home position sensor.

Main code

Sub code

Details of trouble


L4 01 Content Main motor lock detectionDetail When the main motor encoder pulse is not

detected for 100 msec.Cause Main motor unit abnormality

Improper connection or disconnection the main motor and the harness.MCU PWB abnormality

Check and remedy

Use SIM 25-01 to check the main motor operations.Check connection of the main motor harness/connector.Replace the main motor.Replace the MCU PWB.

32 Content Exhaust fan motor lock detection troubleDetail The error detection is started after 2 sec

from starting rotation of the exhaust fan motor.1) The continuous rotation state of 250ms is

not detected for 1 sec after starting detection.

2) When the lock sensor (in the exhaust fan) detects the HIGH level (unstable) after detection the lock state (stable state).

Cause Exhaust fan motor connector connection troubleExhaust fan motor troubleMCU PWB trouble

Check and remedy

Exhaust fan motor connector connection checkExhaust fan motor replacementReplace the MCU PWB.

L6 10 Content Polygon motor lock detectionDetail The lock signal (specified rpm signal) does

not return within a certain time (about 20 sec) from starting the polygon motor rotation.

Cause Polygon motor unit abnormalityImproper connection or disconnection of the polygon motor and the harness.MCU PWB abnormality

Check and remedy

Use SIM 61-1 to check the polygon motor operations.Check connection of the polygon motor harness/connector.Replace the polygon motor.Replace the MCU PWB.

U2 04 Content EEPROM read/write error (Serial communication error)

Detail EEPROM access process errorCause EEPROM abnormalityCheck and remedy

Check that the EEPROM is properly set.Use SIM 16 to cancel the trouble.Replace the MCU PWB.

11 Content Counter check sum error (EEPROM)Detail Check sum error of the counter area in the

EEPROMCause EEPROM abnormalityCheck and remedy

Check that the EEPROM is properly set.Use SIM 16 to cancel the trouble.Replace the MCU PWB.

Main code

Sub code

Details of trouble


[11] USER PROGRAMThe conditions of factory setting can be changed according to theuse conditions.

1. Functions that can be set with user programs

Toner save modeReduces toner consumption by approximately 10%.

Power save modesThe unit has two power save modes of operation: preheat modeand auto power shut-off mode.

Preheat mode

When the unit enters the preheat mode, the power save ( ) indi-cator will light up and other indicators will remain on or off asbefore. In this condition, the fuser in the unit is maintained at alower heat level, thereby saving power. To copy from the preheatmode, make desired copier selections and press the start ( )key using the normal copying procedure.

Auto power shut-off mode

When the unit enters the auto power shut-off mode, the powersave ( ) indicator will light up and other indicators except theONLINE indicator will go out. The auto power shut-off mode savesmore power than the preheat mode but requires a longer timebefore starting copying. To copy from the auto power shut-offmode, press the start ( ) key. Then make desired copier selec-tions and press the start ( ) key using the normal copying proce-dure.

Auto clearThe unit returns to the initial settings a preset amount of time afterthe end of job.

This preset amount of time (auto clear time) can be changed.

Resolution of AUTO & MANUAL modeYou can set the copy resolution used for AUTO and MANUAL( ) exposure mode.

2. Toner save mode (AL-2030/2040CS)1) Press the exposure mode selector key to select the MANUAL

( ) mode.

2) Press and hold down the exposure mode selector key forapproximately 5 seconds. The MANUAL ( ) indicator willgo out and the PHOTO ( ) indicator will begin to blink. Thelight and dark indicator marked "5" will light up, indicating thestandard toner mode is active.

3) To enter the toner save mode, press the light ( ) key. Thelight and dark indicator marked "1" will light up, indicating thetoner save mode is selected.

4) Press the exposure mode selector key. The PHOTO ( ) indi-cator will stop blinking and light up steadily. The light and darkindicator marked "3" will light up. The toner save mode is nowactive.

Note: To return to the standard mode, repeat the procedure butuse the dark ( ) key to select exposure level "5" in step3).

3. User programs (AL-2030/2040CS)The user programs allow the parameters of certain functions to beset, changed, or canceled as desired.

Set the power save modes, auto clear time, preheat mode, SPF automatic original discharge time, resolution of AUTO & MANUAL mode and reset factory setting.

1) Press and hold down the light ( ) key simultaneously formore than 5 seconds until all the alarm indicators ( , ,

) blink and " " appears in the display.

2) Use the left copy quantity ( ) key to select a user programnumber (1: Auto clear time, 2: Preheat mode, 3: Auto powershut off mode, 4: Auto power shut off timer, 6: SPF automaticoriginal discharge time, 10: Resolution of AUTO & MANUALmode, 21: Reset factory, 24: Prevention of OC copies whenthe SPF is up function, 25: Copy effective paper width settingfunction (Bypass tray), 26: Copy effective paper width settingfunction (Tray 1), 27: Copy effective paper width setting func-tion (Tray 2) (AL-2040CS only), 28: Selection of copy startstate (Polygon rotation on/off), 29: Fusing temperature settingwhen the bypass tray is used). The selected number will blinkin the left side of the display.

3) Press the start ( ) key. The entered program number will besteadily lit and the currently selected parameter number for theprogram will blink on the right side of the display.

4) Select the desired parameter using the right copy quantity( ) key. The entered parameter number will blink on theright of the display.

Program No.

Mode Parameters

1 Auto clear time 1 → 10 sec., 2 → 30 sec., *3 → 60 sec., 4 → 90 sec., 5 → 120 sec., 6 → OFF

2 Preheat mode *1 → 30 sec., 2 → 60 sec., 3 → 5 min., 4 → 30 min., 5 → 60 min., 6 → 120 min., 7 → 240 min.

3 Auto power shut off mode *1 → ON, 2 → OFF4 Auto power shut off timer *1 → 5 min., 2 → 30min.,

3 → 60 min., 4 → 120 min., 5 → 240 min.

6 SPF automatic original discharge time

1 → 5 min., *2 → 30 min., 3 → 60 min., 4 → 120 min., 5 → 240 min., 6 → OFF

10 Resolution of AUTO & MANUAL mode

*1 → 300dpi, 2 → 600dpi

21 Reset factory 1 → YES, *2 → NO

AL-2030/2040CS/2050CS USER PROGRAM 11 - 1

∗ Factory default settings are indicated with an asterisk (*).

5) Press the start ( ) key. The right-hand number in the displaywill be steadily lit and the entered value will be stored.

Note: To change the setting or to set another mode, press the clearkey. The unit will return to step 2).

6) Press the light ( ) key to return to the normal copy mode.

4. User programs (AL-2050CS)1) Press the [MENU] key and then press the [ENTER] key.

In printer mode, the user programs are accessed by simplypressing the [MENU] key.

2) Press the [ ] key ( ) or [ ] key ( ) to select the itemthat you wish to configure in the USER PROGRAM items, andthen press the [ENTER] key.

• You can also select a program by directly entering the pro-gram number with the numeric keys.

3) Press the [ ] key ( ) or [ ] key ( ) to change the set-ting of the selected item.

Note:

• If you mistakenly select the wrong item, press the [CLEAR] key( ) and repeat the procedure from step 2.

• To cancel a setting for a user program, press the [MENU] key.

4) Press the [ENTER] key.

Your selection appears briefly and then the previous screenappears.

Note: When "AE LEVEL ADJUST" is selected in the user programsand the [ENTER] key is pressed, the automatic exposureadjustment screen appears. Adjust the exposure and pressthe [ENTER] key.

A. Copy mode

24 Prevention of OC copies when the SPF is up function

*1 → ON, 2 → OFF

25 Copy effective paper width setting function (Bypass tray)

*1 → Large (LETTER/A4 width), 2 → Small (INVOICE/B5R width)

26 Copy effective paper width setting function (Tray 1)


27 Copy effective paper width setting function (Tray 2)(AL-2040CS only)


28 Selection of copy start state (Polygon rotation on/off)

*1 → ON, 2 → OFF

29 Fusing temperature setting when the bypass tray is used

1 → Low, *2 → High

Program No.

Mode Parameters

Program number

Program nameSetting codes

(factory default setting appears in bold)

Explanation

1 AUTO CLEAR 1: 10 SEC.2: 30 SEC.3: 60 SEC.4: 90 SEC.5: 120 SEC.6: OFF

• Auto clear time automatically returns the copy settings to the initial settings ifno keys are pressed for a preset period of time following the end of a copyjob.

• This program is used to select the period of time. Auto clear time can also bedisabled.

2 PREHEAT MODE 1: 30 SEC.2: 1 MIN.3: 5 MIN.4: 30 MIN.5: 60 MIN.6: 120 MIN.7: 240 MIN.

• This function automatically switches the machine to a low power consumptionstate if the set duration of time elapses without the machine being used whenthe power is on. The power save indicator lights up, however, the keys on theoperation panel can be used. Normal operation automatically resumes whena key on the operation panel is pressed, an original is placed, a print job isreceived.

3 AUTO SHUT-OFF 1: ON2: OFF

• Use this setting to enable or disable auto power shut-off mode.

4 AUTO SHUT-OFF TIME

1: 5 MIN.2: 30 MIN.3: 60 MIN.4: 120 MIN.5: 240 MIN.

• This function automatically switches the machine to a state that consumeseven less power than preheat mode if the set duration of time elapses withoutthe machine being used when the power is on. All lights except the powersave indicator go off.To resume normal operation, press the [START] key ( ).Normal operation also resumes automatically when a print job is received orscanning is begun from a computer. While in auto power shut-off mode, nokeys (except the [START] key ( )) can be used.

7 LAYOUT IN 2IN1 1: PATTERN 12: PATTERN 2

• Use this setting to select the layout pattern when two original pages arecopied onto a single sheet of paper.

8 OFFSET FUNCTION

1: ON2: OFF

• When enabled, this function offsets the position of each set of copies in theoutput tray in copy mode, and each print job in printer mode.

9 ROTATE ORIG. IMAGE

1: ON2: OFF

• When two-sided copying is performed, this function rotates the image on theback of the original. This is convenient when binding the copies at the top(tablet binding).

10 AE/TEXT RESOLUTION

1: 300dpi2: 600dpi

• This setting is used to change the copy resolution in AUTO and TEXT modefrom 600 x 300 dpi to 600 x 600 dpi (high-quality mode). Scanning is slowerwhen high-quality mode is used.


11 2-SIDED COPY MODE

1: HI-SPEED2: NORMAL

• If the memory fills up when two-sided copying is performed, "NORMAL" canbe selected to make copying possible. However, "NORMAL" results in aslower copying speed. Normally "HI-SPEED" is selected to enable fast two-sided copying.

12 MARGIN WIDTH 1: 1/4"2: 1/2"3: 3/4"4: 1"

• Use this setting to set the margin width.

13 MEM. FOR PRINTER

1: 30%2: 40%3: 50%4: 60%5: 70%

• Use this to change the proportion of machine memory used for printer mode.

14 AUTO KEY REPEAT

1: ON2: OFF

• Use this setting to select whether or not holding down a key causes repeatedinput of the key. For keys that normally cause a set value to decrease orincrease when held down (for example, the [ ] key ( ) or [ ] key( )), this program can be used to have the set value not change when thekey is held down.

15 KEY PRESS TIME 1: NORMAL2: 0.5 SEC.3: 1.0 SEC.4: 1.5 SEC.5: 2.0 SEC.

• Use this setting to select how long a key must be pressed for the input to beaccepted.By selecting a longer time, you can prevent settings from being changed bythe accidental pressing of a key.

16 KEY TOUCH SOUND

1: LOW2: HIGH3: OFF

• This sets the volume of beep signals.

17 SOUND AT DEFAULT

1: ON2: OFF

• Use this to sound a beep when a base setting is selected.

18 TONER SAVE MODE

1: ON2: OFF

• This mode reduces toner usage by about 10% when copying. Toner savemode is effective when the exposure mode is AUTO or TEXT.

19 AE LEVEL ADJUST

1: SPF/RSPF (Adjustment to 5 levels is possible.)

2: DOCUMENT GLASS (Adjustment to 5 levels is possible.)

• This is used to adjust the exposure level.• The automatic exposure level can be adjusted separately for the document

glass and the RSPF.• For the procedure for adjusting the exposure and guidelines for numeric

values. The factory default setting for the exposure level is center.

20 LANGUAGE 1: AMERICAN ENGLISH2: ENGLISH3: FRENCH4: SPANISH

• This is used to set the language used in the display.

21 RESET FACTORY 1: YES2: NO

• This is used to return all settings to the factory default settings.

22 SORT AUTO SELECT

1: ON2: OFF

• Use this setting to enable or disable sort auto select mode.

24 CHECK RSPF OPEN

1: ON2: OFF

• You can set the operation that takes place if the [START] key ( ) is pressedwhen the RSPF is not completely closed.

25 VALID COPY WIDTH

1: 8.5x112: 5.5x8.5

• Set the allowed paper sizes for copying from the bypass tray. When "5.5x8.5"is selected, a copy of a letter size original will only be printed up to invoicesize.

28 LSU SETTING 1: ON2: OFF

• Select whether copying is only allowed when the polygon motor is rotating, oralso when the polygon motor is stopped.

29 PAPER TYPE 1: PLAIN PAPER2: HEAVY PAPER

• Set the temperature of the fusing unit when the bypass tray is used. Normally"PLAIN PAPER" should be selected.

30 DISPLAYCONTRAST

1: LIGHTER2: LIGHT3: NORMAL4: DARK5: DARKER

• Set the contrast of the display.

Program number



Explanation


B. Print mode

* The scanning speed increases when the USB 2.0 mode is set to "HI-SPEED", however, the printing speed does not increase considerably.

Program number



Explanation

1 FORCEDOUTPUT

1: ON2: OFF

• When this function is enabled, printing in printer mode will automaticallycontinue using a different size of paper if the specified size of paper runs outin all trays. This feature does not function in copy mode.

2 USB 2.0 MODESWITCH*

1: FULL-SPEED2: HI-SPEED

• This sets the USB 2.0 data transfer speed. To obtain the fastest speed whenusing the USB 2.0 connector, first verify that your computer meets thesystem requirements (operating system and driver), and then use thisprogram to change the USB 2.0 mode to "Hi-Speed". Note that the settingshould not be changed while running a TWAIN driver.

3 AUTO TRAYSWITCH

1: ON2: OFF

• If the paper runs out during printing and there is paper of the same size inanother tray, this function automatically switches to that tray (excluding thebypass tray). The function can be disabled.


[12] ELECTRICAL SECTION

1. Block diagramA. Overall block diagram

(1) AL-2030/2040CS

Ca

rria

ge

Un

it

CC

DP

WB

12V

5V

NF

A5V

3.3V

Reg

5V

SPFM

oto

rM

ech

an

icalL

oa

d

RMPF

S,RR

S,CPF

S1

G8bits(M

SB/L

SB)

B(C

ou

nte

r)MCNT

5V

Se

nso

r/SW

(Ele

cto

ricald

ete

cto

r/SW/S

en

so

r)

CPUINTERRUPT

SPPD

PSW

MC

U-P

WB

FW

MHP

S

CPUI/O

Inte

rlo

ck

SW

Ca

sse

tte

de

tecto

rX2

DrumIn

itiald

ete

cto

r

3.3V

PPD1

POD

MFD

PPD2

SPOD

Prin

terCLK

(18

.3856MHz)

3.3V

Sca

nn

erCLK(48MHz)

A[19…1]

OPEPWB

D[15…0]

USBI/F

1Mb

it

16Mb

it

Duple

xM

oto

r

16b

it

FanM

oto

rI2CBu

s

(2sp

ee

d,L

ock

se

nso

r)8Kbyte

24V

12V

2n

dC

as

se

tte

Ma

inM

oto

rT

on

erM

oto

rM

irro

rM

oto

r

(AL2040

only)

Polyg

on

Me

ch

an

icallo

ad

Moto

r

CPF

S2

Se

nso

r/SW

PAPD,PPD3,

PD2,CED2

ACC

ode

LSU

KRONO

SA

SIC

(296

pin)

CPU

H8S/2321

(19

.6608MHz)

EEPROM

SDRAM

16Mbyte(AL2040)

or8Mbyte(AL2030)

ResetIC

SRAM

Drive

r

Fla

shROM

AFE(HT82V24)

CD

SAGC

MPX

AD

16b

its

CCDD

rive

r

CCFL

x2

Lam

pIn

vert

er

forCCFL

HOME

PO

SITION

SEN

SOR

CCD

(ILX558X)

CPUCLK(19.6608MHz)

SystemR

eset S

SCG

PMD

Drive

r

LEDD

rive

rLED AL203044

pcs

AL204048

pcs

HC151

x2

KEYM

atr

ix

AL203013

pcs

AL204015

pcs

STARTKEY

POWER

SUPPLY

/POFF,HL,PR

FW3

.3V,5VEN,5V,12V,24V

HVU

TC,GRID,MC,BIA

S

PMCLK

PSW

KEYIN1,2

SELIN1,2,3

OP-CLK

OP-LATCH

OP-DATA

PSL

MHP

S

Drive

r

/MMD

PWM

0-24V

HC151

DC-DC

/MMRDY

LA

SER

MMCLK

USB1T20

PSLLED

Drive

r

ONLLED

ONL

Drive

r

NICPCBA

(AL2040

only)

RJ45

(N/W

connecto

r)E

therC

hip

RTL8019A

S

FPGA

CPU

uPD703100

Fla

shROM

1Mb

it

SRAM

256

kbit

1284I/F

AL2040

only

USB2.0

FullSpeed

AL-2030/2040CS/2050CS ELECTRICAL SECTION 12 - 1

(2) AL-2050CS

Car

riag

e U

nit

12V

12V

Reg

A5V

3.3V

SP

F M

otor

R G8b

its (

MS

B/L

SB

)B

FA

X M

od

el O

nly

AR

-FX

135V

Spe

aker

Mec

han

ical

Lo

ad

MC

U-P

WB

MP

FS

,RR

S,C

PF

S1

(RS

PF

UN

IT S

PU

S,S

RV

C)

3.3V

8Mb

256M

bx1

or 1

6Mb

1284

I/F

D[7

..0]

AR

-NB

2AR

D12

MH

z(A

R O

ptio

n)C

SIN

TS

enso

r/S

WP

rinte

r C

LKE

ther

net

(E

lect

oric

al d

etec

tor/

SW

/Sen

sor)

/ES

PR

DC

PU

INT

ER

RU

PT

SP

PD

18.3

856M

Hz

3.3V

18.3

856M

Hz

UA

RT

CP

U I/

ON

W P

WB

Inte

rlock

SW

Cas

sette

det

ecto

r X

2D

rum

Initi

al d

etec

tor

Sca

nner

CLK

(12M

Hz

x448

MH

z)A

[19…

1]P

PD

1P

OD

D[1

5…0]

MF

DP

PD

21M

bit

OP

E P

WB

16

Mbi

tS

PID

SR

JDS

CO

D

Dup

lex

Mod

el O

nly

CP

UC

LK8b

itD

uple

x M

otor

FA

X M

odel

Onl

yI2

C B

us

8bit

FA

X O

PE

PW

BA

R-F

X13

D[1

5…8]

8Kby

teS

hifte

r M

otor

Buz

zer

Fan

Mot

or24

V12

V

(AR

Mod

el O

nly)

2nd

Cas

sett

eM

ain

Mot

orT

oner

Mot

orM

irror

Mot

or

Mec

hani

cal l

oad

CP

FS

2

Sen

sor/

SW

Pol

ygon

M

otor

PP

D3,

PD

2,C

ED

2

AC

Cod

e

LSU

KR

ON

OS

AS

IC

(296

pin)

CP

UH

8S/2

321

(19.

6608

MH

z)

EE

PR

OM

SD

RA

M8M

byte

Res

et IC

SR

AM

Driv

er

Fla

sh R

OM

AF

E(H

T86

V26

)

C D S

A G C

M P X

AD

16bi

ts

CC

D D

river

CC

FL

x 2

Lam

p In

vert

erfo

r C

CF

L

HO

ME

PO

SIT

ION

SE

NS

OR

CC

D(I

LX55

8K)

CP

U C

LK(1

9.66

08M

Hz)

Sys

tem

Res

et

SS

CG

PMD

Driv

er

LED

Driv

erLE

D

HC

151

KE

Y M

atrix

ST

AR

T K

EY

PO

WE

R S

UP

PL

Y

/PO

FF,H

L,P

RFW 3.

3V,5

VE

N,5

V,1

2V,2

4V

HV

U

TC

, GR

ID, M

C, B

IAS

PMCLK

PS

W

KE

YIN

SE

LIN

1,2,

3

OP

-CLK

OP

-LA

TC

HO

P-D

AT

A

PS

L

MH

PS

Driv

er

Driv

er

/MMD

PW

M

0 -

24V DC

-DC

Imag

e B

US

(PI-

Bus

)Im

age

BU

S(P

O-B

us)

OA

982

SD

RA

MF

lash

RO

M

/MMLD

8

KE

YS

CA

N1-

3

ISP

1583

USB2.0High-speed

P-B

us

LCD

(2 x

20)

FA

X I/

F

HC

238

(3 to

8 d

ecod

e)

EE

PR

OM

(CR

UM

)

LCD

ELC

D R

SLC

D R

/W(T

BD

)LC

D D

B7-

4

FA

X M

ain

PC

BA

Driv

er

IO A

SIC

LAS

ER

KE

Y M

atrix

LED

NIC

PC

BA

(A

L M

odel

onl

y)R

J45

(N/W

conn

ecto

r)E

ther

Chi

pR

TL8

019A

S

FP

GA

CP

UuP

D70

3100

Fla

shR

OM

1Mbi

tS

RA

M25

6kbi

t

MMCLK

PS

L LE

D

8

SS

CG

PMRDY

Driv

er

Net

wor

k B

ox10

0Bas

e-T


2. Actual wiring diagramA. AL-2030

(1) MCU PWB (1/2)DHAI-0519Q

SPZ

DHAI-0287Q

SZZ

CN22

CN2

DHAI-0513Q

SPZ

CN304

CN303

DHAI-0270Q

SZZ

LEDPPD2

LEDPPD2

11

11

PPD2

22

22

D-GND

33

3

44

55

B5B-PH-K-S

66

77

88

CN11

99

10

10

11

11

12

12

13

13

B4B-PH-K-S

14

14

15

15

16

16

17

17

18

18

IMSA-9619S-18A

CN13

B05B-XA

SK-1

DHAI-0286Q

SZZ

CN19

CN4

1 2B3B-PH-K-S

3 4

B4B-PH-K-R

DHAI-0530Q

SPZ

CN42

8 7 6CN3

DHAI-0268Q

SZ3

51

1

42

2

33

3

24

4

15

5

B08B-CZHK-B

66

77

88

99

10

10

DHAI-0529Q

SPZ

CN41

11

11

512

12

413

13

314

14

215

15

116

16

1B05B-CZHK-B

17

17

2

18

18

19

19

CN25

20

20

21

21

22

22

23

23

B3B-PH-K-M

24

24

25

25

DHAI-0514Q

SPZ

CN6

26

26

1

27

27

2

28

28

3

29

29

4

30

30

5

31

31

B5B-PA

SK-1

32

32

FF4-32-S15D5

CN23

B2P-VH

CN5

DHAI-0526Q

SPZ

11

1

CN12

22

2

36

6

45

5

B4B-PH-K-R

88

B3B-PH-K-E

DHAI-0515Q

SPZ

11

CN10

2

DHAI-0273Q

SZZ

CN1

DHAI-0525Q

SPZ

1

B3B-PH-K-S

11

4

22

33

44

DHAI-0292Q

SZZ

DHAI-0269Q

SZZ

CN7

55

1

CED1

16

6

D-GND

27

7

88

DHAI-0267Q

SPZ

B3B-PH-K-K

B24B-PNDZ

S-1

1

DHAI-0289Q

SZZ

CN16

CN1

B3B-PH-K-R

91

10

2

11

3

12

41

DHAI-0510Q

SP1

DHAI-0511Q

SP1

CN26

13

52

11

14

62

2

15

716

817

9

18

10

B5B-PH-K-R

19

11

20

12

21

13

1

DHAI-0272Q

SZZ

CN15

22

14

2

23

15

24

16

B2P-VH-R

B24B-PNDZ

S-1

L N

3 4 5

HLN

TMB_O

/RR

S

1 2

/MMCLK

MMLD

/MMCLK

TMA_O

-VIDEO

-S/H

D-GND

MMLD

-HSYNC

D-GND

+5V

-LDEN

3

STROBE

PSL

KIN2

3/DMT_1

5VDR

ST

D-GND

HLL

HLN

P-GND

/PMD

PMRDY

PMCLK_A

5 14

CCD_PHI1

(AFE_DB7)

SELIN1

OP-CLK

SELIN2

OP-LATCH

OP-DATA

5VEN

ONL

PSW

D-GND

24V

24V1(D

SW

S)

CCD-R

S

(BSAMP)

CCD-CP

(AFE_SDI)

CCD_PHI2

D-GND

(AFE_DB5)

(AFE_SCK)

OUTA-

OUTB-

CCD-TG

P-GND

P-GND

EN5V

VCL

VCL

12V

12V

D-GND

/DMT_3

124VDupMT

21 2 3 15

DR

ST

/DMT_2

2/DMT_0

4 323

24V

D-GND

D-GND

LEDPPD1

2

PPD1

(AFE_DB0)

(AFE_DB2)

(AFE_DB1)

DV

SEL

TC

S

24V

INT24V

/MMD

2

CED1

1

24V

1 2 2

PGND

SELIN3

OP-STB

D-GND

(VSAMP)

SELIN1

OP-DATA

OP-LATCH

5VKEYIN2#

OP-CLK

DR

ST

D-GND

D-GND

KIN1

DR

ST

D-GND

ONL

SELIN2

PSL

PSW

EN5V

KEYIN1#

D-GND

SELIN3

D-GND

D-GND

LEDPOD

POD

OUTB+

OUTA+

D-GND

VFMOUT

PGND

1

PPD2

D-GND

1 2FANLK

/VFMCNT

3 4

22

D-GND

RTH_IN

15

RTH_IN

D-GND

1 2 3

1 2 3

D-GND

53 4

24V

D-GND

1 2 3 4

D-GND

/LDEN

/VIDEO

SHOLD

53 46 87 1 2

(VSAMP)

2

D-GND

3 1 1

(AFE_SEN)

(ADCLK)

D-GND

PMCLK_A

12V

12V

EN5V

D-GND

P-GND

P-GND

VCL

VCL

CCD-TG

D-GND

CCD-R

S

(BSAMP)

CCD-CP

(AFE_

SDI)

CCD_PHI2

D-GND

CCD_PHI1

(AFE_

SEN)

(AFE_DB5)

(AFE_DB6)

VCL

P-GND

(AFE_DB4)

(AFE_DB3)

MHP

S

D-GND

(ADCLK)

D-GND

(AFE_

SCK)

(AFE_DB7)

D-GND

(AFE_DB0)

(AFE_DB2)

(AFE_DB1)

D-GND

mt_

at_

hom

e

(AFE_DB6)

(AFE_DB4)

(AFE_DB3)

MC

24V

TC

S

DV

SEL

D-GND

BIA

S

/GRIDL

INT5V

INT24V

BIA

S

F-GND

MCFB

TC

BC

/BIA

S

/TC

/GRIDL

/MC

INT5V

INT24V

EN5V

3.3VIN

5V

GRID

/MC

/BIA

S

/TC

D-GND

P-GND

D-GND

3.3VIN

/POFF

12VIN

24V

FW

P-GND

24V

/PR

HLOUT

P-GND

HLL

D-GND

P-GND

D-GND

3.3VIN

EN5V

3.3VIN

5V

P-GND

/PR

HLOUT

P-GND

24V

/POFF

12VIN

24V

FW

D-GND

P-GND

2PD1

1

PMRDY

/PMD

/SYNC

INT5V

D-GND

3

24V

/CPF

S1

1 2 3 1

INT24V

PGND

/MMD

3

DGND

24V

/MPF

S

5 MFD

PP

D2

Th

erm

isto

r

Fan

MT

PO

D

PO

LY

GO

NM

T

LD

TO

NE

RM

T

RE

SIS

TR

OL

LE

R

SO

LE

NO

ID

CA

SS

ET

TE

PA

PE

R

SO

LE

NO

ID

CE

D1 PP

D1

DR

ST

OP

E

PW

B

SC

AN

NE

R

MT

CC

D

PW

B

INV

ER

TE

R

PW

B

CL

CL

TC

SD

V

un

HV

TP

WB

PO

WE

R

SU

PP

LY

PW

BA

C-C

OR

D

MC

UP

WB

MA

INM

T

AL

MO

DE

LO

NL

Y

TH

ER

MO

ST

AT

HL

SC

AN

NE

R

UN

MP

FS

SO

LE

NO

ID


(2) SPF unit (2/2)

CN24

DHAI-0532Q

SP1

B12B-PH-K-S

24V

SPFMT

1

24V

SPFMT

2

SPMT_0

3

SPMT_2

4

SPMT_1

5

SPMT_3

6

SPID

7

DGND

8

LED

SPID

9

SPPD

10

DGND

11

LED

SPPD

12

2DGND

3LED

SPPD

3LED

SPID

1SPPD

SPID

2DGND

3B

1/B

1

A

6/A

5COMA

2COMB

4

MC

U

PW

BS

PID

SP

MT

SP

FU

NIT

SP

PD


B. AL-2040CS

(1) MCU PWB (1/2)DHAI-0519Q

SPZ

DHAI-0287Q

SZZ

CN22

CN2

DHAI-0513Q

SPZ

CN304

CN303

DHAI-0270Q

SZZ

11

11

11

22

22

22

33

33

3

44

11

55

22

B5B-PH-K-S

66

77

88

CN11

99

10

10

11

11

12

12

13

13

B4B-PH-K-S

14

14

15

15

16

16

17

17

18

18

IMSA-9619S-18A

CN13

B05B-XA

SK-1

DHAI-0286Q

SZZ

CN19

CN4

1 2B3B-PH-K-S

3 4

B4B-PH-K-R

DHAI-0530Q

SPZ

CN42

-HSYNC

8

D-GND

7

+5V

6CN3

DHAI-0268Q

SZ3

51

1

-LDEN

42

2

-VIDEO

33

3

-S/H

24

4

D-GND

15

5

B08B-CZHK-B

66

77

88

99

10

10

DHAI-0529Q

SPZ

CN41

11

11

512

12

413

13

314

14

215

15

116

16

1B05B-CZHK-B

17

17

218

18

19

19

CN25

20

20

21

21

22

22

23

23

B3B-PH-K-M

24

24

25

25

DHAI-0514Q

SPZ

CN6

26

26

127

27

228

28

329

29

430

30

531

31

B5B-PA

SK-1

32

32

FF4-32-S15D5

CN23

B2P-VH

CN5

DHAI-0526Q

SPZ

11

1

CN12

22

2

36

6

45

5

B4B-PH-K-R

88

B3B-PH-K-E

DHAI-0515Q

SPZ

11

CN10

2

DHAI-0273Q

SZZ

CN1

DHAI-0525Q

SPZ

1

B3B-PH-K-S

11

4

22

33

44

DHAI-0292Q

SZZ

DHAI-0269Q

SZZ

CN7

55

1

CED1

66

D-GND

77

88

DHAI-0267Q

SPZ

B3B-PH-K-K

B24B-PNDZ

S-1

1

DHAI-0289Q

SZZ

CN16

CN1

B3B-PH-K-R

91

10

2

11

3

12

41

DHAI-0510Q

SP1

DHAI-0511Q

SP1

CN26

13

52

11

14

62

2

15

716

817

9

18

10

B5B-PH-K-R

19

11

20

12

21

13

1

DHAI-0272Q

SZZ

CN15

22

14

2

23

15

24

16

B2P-VH-R

B24B-PNDZ

S-1

L N

1 2

TMA_O

TMB_O

/RR

S

1

D-GND

MMLD

/MMCLK

LEDPPD2

PD1

MMLD

/MMCLK

PPD2

LEDPPD2

D-GND

RTH_IN

KIN2

3/DMT_1

5VDR

ST

D-GND

5V

/DMT_0

OP-DATA

5VEN

SELIN1

OP-CLK

SELIN2

OP-LATCH

D-GND

(AFE_

SCK)

(AFE_

SEN)

(ADCLK)

D-GND

24V

/MPF

S

24V

CCD-R

S

(BSAMP)

CCD-CP

(AFE_

SDI)

CCD_PHI2

D-GND

CCD_PHI1

24V1(D

SW

S)

5 MFD

DGND

3

PPD1

D-GND

CED1

D-GND

LEDPPD1

1 2

D-GND

3

(AFE_DB4)

(AFE_DB3)

EN5V

(AFE_DB0)

(AFE_DB2)

(AFE_DB1)

(AFE_DB7)

(AFE_DB5)

(AFE_DB6)

mt_

at_

hom

e

OP-STB

D-GND

(VSAMP)

CCD-TG

P-GND

P-GND

OP-LATCH

PSL

ONL

PSW

FANLK

/VFMCNT

PGND

24V

/DMT_3

24VDu

pMT

/DMT_2

PMRDY

/PMD

D-GND

KEYIN1#

SELIN3

STROBE

VFMOUT

PPD2

D-GND

D-GND

RTH_IN

DR

ST

D-GND

D-GND

KIN1

SELIN3

OUTB+

OUTA-

OUTB-

OUTA+

D-GND

DR

ST

SELIN1

OP-CLK

D-GND

D-GND

PMCLK_A

3

DR

ST

D-GND

D-GND

LEDPOD

POD

5

SELIN2

KEYIN2#

PSW

D-GND

PSL

ONL

OP-DATA

EN5V

3 4 1 2 34 51 2

D-GND

53 4

VCL

VCL

12V

12V

8 1 2

D-GND

D-GND

P-GND

24V

1 2 3 4 1 2 1 253 46 72 1 132 2 3 4 5 2

P-GND

P-GND

VCL

VCL

12V

12V

EN5V

D-GND

(VSAMP)

CCD-TG

D-GND

CCD-R

S

(BSAMP)

CCD-CP

(AFE_

SDI)

CCD_PHI2

D-GND

CCD_PHI1

(AFE_

SEN)

(AFE_DB5)

VCL

P-GND

(AFE_DB6)

D-GND

(ADCLK)

D-GND

(AFE_

SCK)

(AFE_DB7)

MHP

S

(AFE_DB0)

(AFE_DB4)

(AFE_DB3)

(AFE_DB2)

(AFE_DB1)

D-GND

D-GND

24V

DV

SEL

TC

S

BIA

S

24V

TC

S

DV

SEL

BIA

S

F-GND

MC

/GRIDL

INT5V

INT24V

INT5V

INT24V

BC

/BIA

S

/TC

/GRIDL

/MC

D-GND

P-GND

D-GND

3.3VIN

EN5V

3.3VIN

5V/POFF

12VIN

24V

FW24V

/PR

HLOUT

P-GND

P-GND

D-GND

P-GND

D-GND

3.3VIN

EN5V

3.3VIN

5V/POFF

12VIN

24V

FW

P-GND

24V

/PR

HLOUT

P-GND

21 2D-GND

23 4 5 11

SHOLD

/SYNC

INT5V

D-GND

/LDEN

/VIDEO

/PMD

PMRDY

PMCLK_A

2 3

INT24V

/MMD

PGND

24V

GRID

MCFB

TC

/MC

/BIA

S

/TC

HLN

HLL

HLL

3HLN

/CPF

S1

1

INT24V

PGND

/MMD

1

24V

P-GND

PP

D2

Th

erm

isto

r

Fa

nM

T

PO

D

PO

LY

GO

NM

T

LD

TO

NE

RM

T

RE

SIS

TR

OL

LE

R

SO

LE

NO

ID

CA

SS

ET

TE

PA

PE

R

SO

LE

NO

ID

CE

D1 PP

D1

DSW

DR

ST

OP

E

PW

B

SC

AN

NE

R

MT

CC

D

PW

B

INV

ER

TE

R

PW

B

CL

CL

TC

SD

V

un

HV

TP

WB

PO

WE

R

SU

PP

LY

PW

BA

C-C

OR

D

12

0V

/60

Hz

MC

UP

WB

MA

INM

T

DU

PL

EX

MT

AL

MO

DE

LO

NL

Y

TH

ER

MO

ST

AT

HL

SC

AN

NE

R

UN

MP

FS

SO

LE

NO

ID


(2) SPF unit (2/2)

CN24

DHAI-0532Q

SP1

B12B-PH-K-S

24V

SPFMT

1

24V

SPFMT

2SPMT_0

3

SPMT_2

4

SPMT_1

5

SPMT_3

6

SPID

7

DGND

8

LED

SPID

9

SPPD

10

DGND

11

LED

SPPD

12

2DGND

3LED

SPPD

3LED

SPID

1SPPD

SPID

2DGND

3B

1/B

1

A

6/A

5COMA

2COMB

4

MC

U

PW

BS

PID

SP

MT

SP

FU

NIT

SP

PD


C. AL-2050CS

(1) MCU PWB (1/2)D

HA

I-05

19Q

SP

ZD

HA

I-02

87Q

SZ

ZC

N11

CN

3D

HA

I-05

17Q

SP

ZC

N30

2C

N30

3D

HA

I-02

70Q

SZ

Z1

LED

PP

D2

1LE

DP

PD

21

321

12

PP

D2

22

312

23

D-G

ND

33

303

429

528

2D

-GN

D2

B5B

-PH

-K-S

627

726

825

CN

169

2410

2311

2212

2113

20B

4B-P

H-K

-S14

1915

1816

1717

1618

15C

N27

1914

2013

2112

2211

2310

249

258

267

276

285

CN

2029

430

331

232

1

B05

B-X

AS

K-1

Dup

lex

Mod

elon

lyC

N22

1

DH

AI-

0286

QS

ZZ

CN

262 3 4

B4B

-PH

-K-R

B3B

-PH

-K-S

CN

4D

HA

I-02

68Q

SZ

41

1

DH

AI-

0530

QS

P1

CN

422

2

-HS

YN

C8

33

D-G

ND

74

4

+5V

65

5

56

6

-LD

EN

47

7

-VID

EO

38

8

-S/H

29

9

D-G

ND

110

10

B08

B-C

ZH

K-B

1111

1212

CN

213

1314

1415

15D

HA

I-05

29Q

SP

1C

N41

1616

15

1717

24

1818

319

19C

N3

220

201

2121

B05

B-C

ZH

K-B

2222

2323

2424

CN

2825

2526

26P

D1

2727

2828

B3B

-PH

-K-M

2929

3030

3131

3232

DH

AI-

0514

QS

PZ

CN

12FF

4-32

-S15

D5

1 2 3M

MLD

4M

MLD

/MM

CLK

5/M

MC

LKB

5B-P

AS

K-1

CN

25T

MA

_OT

MB

_OB

2P-V

H

CN

18C

N6

11

1/R

RS

22

23

66

B3B

-PH

-K-E

45

5B

4B-P

H-K

-R8

8

CN

15D

HA

I-05

15Q

SP

Z1

MC

12

B3B

-PH

-K-S

DH

AI-

0273

QS

ZZ

CN

2D

HA

I-05

25Q

SP

Z1

11

42

2D

HA

I-02

69Q

SZ

ZC

N21

33

CE

D1

14

4D

HA

I-02

92Q

SZ

ZD

-GN

D2

55

16

6B

3B-P

H-K

-K7

78

8D

HA

I-02

67Q

SP

ZB

24B

-PN

DZ

S-1

1

DH

AI-

0289

QS

ZZ

CN

24

CN

2D

HA

I-05

25Q

SP

Z

B3B

-PH

-K-R

91

102

DH

AI-

0510

QS

P1

(for

100V

area

)11

3D

HA

I-05

36Q

SP

Z(f

or20

0Var

ea)

124

HLL

1C

N14

135

21

11

146

HLN

22

215

73

168

DH

AI-

0511

QS

P1

(for

100V

area

)4

179

DH

AI-

0537

QS

PZ

(for

200V

area

)5

1810

For

120V

area

B5B

-PH

-K-R

1911

2012

2113

L1

DH

AI-

0272

QS

ZZ

CN

1022

14N

223

1524

16

B2P

-VH

-RB

24B

-PN

DZ

S-1

For

200V

area

DH

AI-

0491

QS

ZZ

MC

FB

GR

ID

TC

BC

124

VD

upM

T

(AF

E_D

B6)

D-G

ND

(AF

E_D

B4)

(AF

E_D

B3)

(AF

E_S

CK

)

mt_

at_h

ome

(AF

E_D

B5)

AC

VO

UT

(AF

E_D

B2)

1D

-GN

DG

ND

3

CC

D_P

HI1

(AF

E_S

EN

)(A

FE

_SE

N)

(AD

CLK

)(A

DC

LK)

CC

D_P

HI1

CC

D_P

HI2

VC

LD

-GN

DP

-GN

D

CC

D-C

PG

ND

3(A

FE

_SD

I)

(BS

AM

P)

(BS

AM

P)

AC

VO

UT

1

D-G

ND

D-G

ND

CC

D-R

SC

CD

-RS

(VS

AM

P)

(VS

AM

P)

CC

D-T

GC

CD

-TG

EN

5VE

N5V

D-G

ND

D-G

ND

12V

12V

12V

12V

VC

LV

CL

VC

LV

CL

OU

TB

-

P-G

ND

P-G

ND

P-G

ND

P-G

ND

/SF

TM

T_3

OU

TA

+O

UT

B+

OU

TA

-

5V D-G

ND

VC

C3

D-G

ND

/SF

TM

T_0

3/S

FT

MT

_14

/SF

TM

T_2

LCD

E

3/D

MT

_1

LCD

RS

LCD

CO

NT

BZ

R

LCD

RS

/DM

T_0

124

VS

FT

MT

24V

/MP

FS

24V

24V

1(D

SW

S)

5 MF

DD

GN

D

3

PP

D1

D-G

ND

CE

D1

D-G

ND

LED

PP

D1

1 2D

-GN

D3

(AF

E_D

B1)

(AF

E_D

B0)

(AF

E_D

B7)

FA

NLK

/VF

MC

NT

PG

ND

CC

D-C

P(A

FE

_SD

I)C

CD

_PH

I2D

-GN

D

OP

_LA

TC

H

PS

W

LCD

D6

LCD

D5

PS

LD

RS

T

D-G

ND

24V

/DM

T_3

/DM

T_2

PM

RD

Y/P

MD

D-G

ND

D-G

ND

BL

INF

OLE

DO

P_L

AT

CH

VF

MO

UT

PP

D2

D-G

ND

D-G

ND

RT

H_I

N

DR

ST

D-G

ND

D-G

ND

BL

INF

OLE

D

BZ

RLC

DC

ON

T

D-G

ND

OP

_CLK

LCD

D7

LCD

D4

OP

_CLK

OP

_DA

TA

PS

W

D-G

ND

PM

CLK

_A

3

DR

ST

D-G

ND

D-G

ND

LED

PO

DP

OD

5

OP

_DA

TA

LCD

ELC

DD

4

LCD

D7

LCD

D6

LCD

D5

PS

LD

RS

T

3 4 1 2 34 522 5

D-G

ND

53 4 8 1 2

D-G

ND

P-G

ND

24V

1 253 4 1 2 1 132 2

D-G

ND

(AF

E_S

CK

)(A

FE

_DB

7)M

HP

S(A

FE

_DB

5)(A

FE

_DB

6)D

-GN

D(A

FE

_DB

4)(A

FE

_DB

3)(A

FE

_DB

2)

(AF

E_D

B1)

(AF

E_D

B0)

D-G

ND

D-G

ND

24V

DV

SE

LT

CS

BIA

S

24V

TC

SD

VS

EL

BIA

SF

-GN

D

/GR

IDL

INT

5VIN

T24

V

P-G

ND

INT

5VIN

T24

VP

-GN

D

/BIA

S

/GR

IDL

/MC

D-G

ND

/MC

5V /PO

FF

12V

IN

P-G

ND

D-G

ND

3.3V

INE

N5V

24V

FW

24V

/PR

HLO

UT

P-G

ND

P-G

ND

D-G

ND

P-G

ND

D-G

ND

3.3V

INE

N5V

3.3V

IN5V

1

P-G

ND

24V

/PR

HLO

UT

P-G

ND

/PO

FF

12V

IN24

VF

W

1

SH

OLD

/SY

NC

INT

5VD

-GN

D

/LD

EN

/VID

EO

6 72

/PM

DP

MR

DY

PM

CLK

_A

2 3

INT

24V

/MM

DP

GN

D

24V

/CP

FS

1

1

INT

24V

PG

ND

/MM

D

223 4 5

HLN

HLL

3

P-G

ND

/BIA

S/T

C

P-G

ND

3.3V

IN

/TC

1

24V

P-G

ND

KE

YIN

SE

LIN

3S

ELI

N2

SE

LIN

1D

-GN

DE

N5V

D-G

ND

KE

YS

C1

KE

YS

C2

KE

YS

C3

1 21 2 3 4

KE

YS

C1

KE

YS

C2

KE

YS

C3

KE

YIN

SE

LIN

3S

ELI

N2

SE

LIN

1D

-GN

D

VC

C3

D-G

ND

EN

5VD

-GN

D5V D

-GN

D

PP

D2

Th

erm

isto

r

Fan

MT

PO

D

PO

LY

GO

NM

T

LD

TO

NE

RM

T

RE

SIS

TR

OL

LE

RS

OL

EN

OID

CA

SS

ETT

EP

AP

ER

SO

LEN

OID

CE

D1 PP

D1

DS

W

DR

ST

LC

D_O

PE

PW

B

TC

SD

V un

HV

TP

WB

PO

WE

RS

UP

PL

YP

WB

AC

-CO

RD

MC

UP

WB

MA

INM

T

DU

PL

EX

MT

AL

MO

DE

LO

NLY

TH

ER

MO

ST

AT

HL

MP

FS

SO

LE

NO

ID

SH

IFT

ER

MT

SC

AN

NE

RM

T

CC

DP

WB

INV

ER

TE

RP

WB

CC

FL

CC

FL

SC

AN

NE

RC

arri

age

UN

AC

-IN

LET

AC

-CO

RD


(2) RSPF section (2/2)

CN

30D

HA

I-05

33Q

SP

ZD

HA

I-05

41Q

SP

Z

DH

AI-

0540

QS

PZ

DH

AI-

0539

QS

PZ

B24

B-P

ND

ZS

-1

/B CO

MB

B A /A

24V

12

SR

VC

2

2_S

PU

S2

11S

PID

11

24V

1

3LE

D_S

PID

32

D-G

ND

2

1

21

SP

PD

1

3LE

D_S

RJD

32

D-G

ND

21

SR

JD

SP

ID2

DG

ND

3LE

DS

PID

1S

CO

D2

DG

ND

3LE

D_S

PP

D3

2D

-GN

D

2D

GN

D3

LED

SP

PD

3LE

DS

RJD

1S

PP

D

LED

SC

OD

SR

JD2

DG

ND

1 6313 1 5C

OM

A

2 4

LED

_SR

JD1

LED

_SP

PD

2

DG

ND

3

DG

ND

4

SR

JD5

SP

PD

6LE

D_S

CO

D7

LED

_SP

ID8

DG

ND

9

DG

ND

10

SC

OD

11

SP

ID12

NC

15

SP

MT

_116

24V

SP

FS

OL

13

24V

SP

FS

OL

17

SP

MT

_218

SP

MT

_314

SP

US

19

SP

MT

_020

24V

SP

FS

OL

21

24V

SP

FM

T22

SR

VC

23

24V

SP

FM

T24

MC

UP

WB

SR

JD

SP

MT

RS

PF

UN

IT

SP

PD

SC

OD

SP

ID

SP

US

SR

VC


D. AL-2040CS/2050CS

(1) 2nd cassette unit (1/2)

(2) NIC PWB (2/2)

3. Signal name listSignal name Name Function/Operation Section

LEDPPD2 PPD2 sensor power Fusing sectionPPD2 PPD2 sensor Paper transport detection Fusing sectionRTH_IN Thermistor Fusing section thermistor temperature detection Fusing sectionFANLK Fusing fan Fan lock detection signal Optical section MHPS MHPS sensor Carriage HP detection Optical section /MPFS Multi bypass solenoid Optical section /VFMCNT Fan speed signal Fan rotation speed control Optical section VFMOUT Fusing fan Fan drive signal Optical section /DMT_0 DUP motor DUP motor phase control Duplex drive section /DMT_1 DUP motor DUP motor phase control Duplex drive section /DMT_2 DUP motor DUP motor phase control Duplex drive section /DMT_3 DUP motor DUP motor phase control Duplex drive section LEDPOD POD sensor power Paper exit section POD POD sensor Paper transport detection Paper exit section PMCLK_A Polygon motor Clock signal to the polygon motor LSU PMRDY Polygon motor Polygon motor ON/OFF detection signal LSU /PMD Polygon motor Polygon motor drive signal LSU

DHAI-0306QSZZ CN18

B14B-PHDSS-B

CED2 1

D-GND 2

1 24V 1

D-GND 1

5V 3

PPD3 2

5

10

PD2 1

D-GND 2

D-GND

/CPFS2

24V

5V

PPD3

D-GND

PD2

D-GND

CED2

3

5

6

9

1

2

4

7

8

11

12

13

14

10

3

9

10

14

6

3

9

D-GND

CED2

D-GND

FG

4

2

1

5

PD2 96

9

11

13

8 PPD3 7

7 D-GND 8

13 24V 2

11 5V 4

14 /CPFS2 12 /CPFS2 2

MCU PWB

CPFS2

PPD3

PD2

CED2

2nd CASSETTE UN

CN1 DHAI-0518QSPZ CN39

24FMN-BTK-A

VCC3

5V

5V

D-GND

P2

P1

P0

/RESET

P6

P5

P4

P3

PFRR

PBSY

/PACK

P7

23

24

D-GND

DIR3

/IT3

/SELIN3

/AFFFD3

/STB

/FLT

SLCT

19

20

21

22

15

16

17

18

11

12

13

14

7

8

9

10

3

4

5

6

EN5V2

D-GND1

VCC34

EN5V3

PARAD06

/OA_RST5

PARAD28

PARAD17

PARAD410

PARAD39

PARAD612

PARAD511

/ACK14

PARAD713

PE16

BUSY15

/FAULT18

SLCT17

/AUTOFD20

/STB19

/INIT22

/SLCTIN21

D-GND24

/REV23

1

2

MCU

PWB

NIC

PWBTO

NETWORK


/LDEN Laser Laser circuit control signal LSU SHOLD Laser Laser APC signal LSU /SYNC Laser Horizontal sync signal from the LSU LSU /VIDEO Laser Laser drive signal LSU PD1 PD SW sensor 1st CS paper width sensor Not used /MMCLK Main motor Clock signal to the polygon motor Main drive section /MMD Main motor Polygon motor drive signal Main drive section MMLD Main motor Polygon motor ON/OFF detection signal Main drive section TMA_O Toner motor Toner motor phase control Toner motor drive section TMB_O Toner motor Toner motor phase control Toner motor drive section CED1 Machine cassette detection Paper transport section /CPFS1 1st CS pickup solenoid Paper transport section LEDPPD1 PPD sensor power Paper transport section PPD1 PPD sensor Paper transport detection Paper transport section /RRS 1st transport solenoid Paper transport section BZR Buzzer signal Buzzer Operation section DRST Drum reset detection CRU initial detection Operation section KEYIN Key scan input Key detection control Operation section KEYIN1# Key scan input Key detection control Operation section KEYIN2# Key scan input Key detection control Operation section KEYSC1 Key scan output Key scan output Operation section KEYSC2 Key scan output Key scan output Operation section KEYSC3 Key scan output Key scan output Operation section LCDCON LCD control signal Signal for LCD Operation section LCDDB4 LCD data signal Signal for LCD Operation section LCDDB5 LCD data signal Signal for LCD Operation section LCDDB6 LCD data signal Signal for LCD Operation section LCDDB7 LCD data signal Signal for LCD Operation section LCDE LCD control signal Signal for LCD Operation section LCDRS LCD control signal Signal for LCD Operation section ONL Online LED Operation section OP-CLK LED driver control Operation section OP-DATA LED driver control Operation section OP-LATCH LED driver control Operation section PSL Power save LED Operation section PSW Start button control Operation section SELIN1 Select signal 1 HC151 select signal Operation section SELIN2 Select signal 2 HC151 select signal Operation section SELIN3 Select signal 3 HC151 select signal Operation section STROBE LED driver control Operation section OUTA+ Scanner motor Scanner motor phase control Optical drive section OUTA- Scanner motor Scanner motor phase control Optical drive section OUTB+ Scanner motor Scanner motor phase control Optical drive section OUTB- Scanner motor Scanner motor phase control Optical drive section (ADCLK) AFE AFE control signal Scanner unit section (AFE_DB0) AFE Image scan data Scanner unit section (AFE_DB1) AFE Image scan data Scanner unit section (AFE_DB2) AFE Image scan data Scanner unit section (AFE_DB3) AFE Image scan data Scanner unit section (AFE_DB4) AFE Image scan data Scanner unit section (AFE_DB5) AFE Image scan data Scanner unit section (AFE_DB6) AFE Image scan data Scanner unit section (AFE_DB7) AFE Image scan data Scanner unit section (AFE_SCK) AFE AFE control signal Scanner unit section (AFE_SDI) AFE AFE serial data Scanner unit section (AFE_SEN) AFE AFE control signal Scanner unit section (BSAMP) AFE AFE control signal Scanner unit section (VSAMP) AFE AFE control signal Scanner unit section CCD-CP CCD CCD control signal Scanner unit section CCD-RS CCD CCD control signal Scanner unit section CCD-TG CCD CCD control signal Scanner unit section CCD_PHI1 CCD CCD control signal Scanner unit section CCD_PHI2 CCD CCD control signal Scanner unit section VCL Copy lamp Copy lamp control Scanner unit section

Signal name Name Function/Operation Section


DVSEL Developing tank detection Developing section TCS Toner sensor Toner quantity detection Developing section /BIAS HV bias signal HV bias drive Process section /GRIDL HV grid signal Main charger grid control Process section /MC HV MC signal Main charger control Process section /TC HV TC signal Transfer charger grid control Process section /POFF Low voltage power Output power control Power section FW Low voltage power Zero cross detection Power section /PR Heater lamp Power relay control Power section HLOUT Heater lamp Heater lamp control Power section LEDSCOD SCOD sensor power SPF/RSPF sectionLEDSPID SPID sensor power SPF/RSPF sectionLEDSPPD SPPD sensor power SPF/RSPF sectionLEDSRJD SRJD sensor power SPF/RSPF section/RSV_SOL Reverse solenoid SPF/RSPF sectionSCOD SCOD sensor SPF/RSPF cover open sensor SPF/RSPF sectionSPID SPID sensor SPF/RSPF UN paper entry sensor SPF/RSPF sectionSPMT_0 SPF/RSPF motor SPF/RSPF motor phase control SPF/RSPF sectionSPMT_1 SPF/RSPF motor SPF/RSPF motor phase control SPF/RSPF sectionSPMT_2 SPF/RSPF motor SPF/RSPF motor phase control SPF/RSPF sectionSPMT_3 SPF/RSPF motor SPF/RSPF motor phase control SPF/RSPF sectionSPPD SPPD sensor SPF/RSPF transport detection SPF/RSPF section/SPUS Paper feed solenoid SPF/RSPF sectionSRJD SRJD sensor SPF/RSPF paper exit sensor SPF/RSPF section/SRVC Reverse clutch SPF/RSPF sectionCED2 2nd CS cassette detection 2nd cassette section /CPFS2 2nd CS pickup solenoid 2nd cassette section PD2 PD2 SW sensor 2nd CS paper width detection 2nd cassette section PPD3 PPD3 sensor 2nd CS paper transport detection 2nd cassette section /ACK IEEE1284 /ACK signal Network section /AUTOFD IEEE1284 /AUTOFD signal Network section BUSY IEEE1284 BUSY signal Network section /FAULT IEEE1284 /FAULT signal Network section /INIT IEEE1284 /INIT signal Network section PARAD0 IEEE1284 Data bus Network section PARAD1 IEEE1284 Data bus Network section PARAD2 IEEE1284 Data bus Network section PARAD3 IEEE1284 Data bus Network section PARAD4 IEEE1284 Data bus Network section PARAD5 IEEE1284 Data bus Network section PARAD6 IEEE1284 Data bus Network section PARAD7 IEEE1284 Data bus Network section PE IEEE1284 PE signal Network section /REV IEEE1284 /REV signal Network section SLCT IEEE1284 SLCT signal Network section /SLCTIN IEEE1284 /SLCTIN signal Network section /STB IEEE1284 /STB signal Network section /OA_RST Option reset Reset signal to the NIC PWB Network section USB +D USB signal USB section USB -D USB signal USB section /SFTMT0 Shifter motor Shifter motor phase control Shifter motor section/SFTMT1 Shifter motor Shifter motor phase control Shifter motor section/SFTMT2 Shifter motor Shifter motor phase control Shifter motor section/SFTMT3 Shifter motor Shifter motor phase control Shifter motor section

Signal name Name Function/Operation Section


[13] CIRCUIT DIAGRAM

1. MCU PWB (AL-2030/2040CS)5 5

4 4

3 3

2 2

1 1

DD

CC

BB

AA

(SIN

2)

/STBY

/CS

3#

DM

T3

D2

AR

B_I

NT

(SP

PD

)

/WDTOVF

D7

ON

L

AR

B_I

NT

/WD

TO

VF

/CS

5

SC

L

D6

/CS

2#

DM

T2

(SIN

3)

SD

A

D4

/SC

AN

ST

/SC

AN

SP

#

NMI

D2

D10

/ST

BY

/CS

1#

D5

D3

/CS

0#

/CS

3#

DM

T0

A20

D10

CC

D_T

G

SP

FM

T1

/RD

#

D4

(FW

)

D11

D8

(KE

YIN

1)

D8

/LW

R#

D3

D0

/HW

R#

D15

D5

/CS

1#

/SC

AN

ST

PO

FF

/TR

AN

SS

TD

9

SP

FM

T3

/LW

R#

D1

CP

U_S

YN

C

/HW

R#

D9

SP

FM

T2/

MIR

CN

TD

6

(SIN

1)

D11

A12

CP

U_S

YN

C

D13

/SC

AN

SP

#

/CS

0#

/RD

#

DM

T1

/TR

AN

SS

T

D1

MC

NT

A8

CP

UC

LK(N

C)

NM

I

(FW

)

D14

D12

D0

SP

FM

T0

D7

SP

FM

T1

SP

FM

T3

SP

FM

T0

SP

FM

T2/

MIR

CN

T

/ES

SR

DY

RY

/BY

CR

UM

SC

L/P

RIN

TS

T

EX

TA

L

XT

AL

(KE

YIN

2)

/PR

INT

ST

TxD

SD

AR

xDS

CL

PO

FF

/ES

_PA

GE

/MS

U_S

T1

MC

NT

RY

/BY

/ES

SR

DY

(KE

YIN

2)

TxD R

xDC

RU

MS

DT

A

RE

SE

TO

UT

1

ST

RO

BE

ST

RO

BE

A0A1A2A3

A4A5A6A7

A9A10A11

A13A14A15A16A17A18A19

(PS

W)

D12

D13

D14

D15

/CS

5C

RU

MS

DT

AC

RU

MS

CL

RE

SE

TO

UT

1M

MC

LKD

MT

3D

MT

2D

MT

1D

MT

0

XTALEXTAL

CPUCLK(NC)

/ES

_PA

GE

/MS

U_S

T1

PS

L

/CS

2#

CC

D_T

G

VC

C3

CP

U3.

3

VC

C3

CP

U3.

3

VC

C3

VC

C3

VC

C3

RT

H(5

)

(SIN

2)(4

)SE

LIN

1(4

)

(SIN

3)(4

)

SP

FM

T1

(4)

DM

T0

(6)

(SIN

1)(4

)

/CS

1(3

)

CC

D_T

G(2

,4)

DM

T3

(6)

/CS

0(3

)

D_C

ON

T(4

)

DM

T2

(6)

/LW

R(2

)

D[1

5..0

](2

,3)

SP

FM

T3

(4)

A[2

0..0

](2

,3)

/RE

SE

T0

(2,3

,4)

ST

RO

BE

(4)

/TR

AN

SS

T(2

)

CP

U_S

YN

C(2

)

(SP

PD

)(7

)

/RD

(2,3

)

/SC

AN

SP

(2)

AR

B_I

NT

(2)

/RESET1(2,4)

(FW

)(4

)

SE

LIN

3(4

)

SP

FM

T0

(4)

/SC

AN

ST

(2)

DM

T1

(6)

/CS

2(2

)

PM

CLK

(5)

(PS

W)

(7)

/HW

R(3

)

SP

FM

T2/

MIR

CN

T(4

)

/AS

IC_R

ST

(2,4

,12)

SE

LIN

2(4

)M

MC

LK(5

)

/PR

INT

ST

(2)

PO

FF

(2,5

)T

xD(9

)S

DA

(3)

RxD

(9)

SC

L(3

)(U

SB

_IN

)(4

)

(KE

YIN

2)(4

)

(TC

S_A

N)

(5)

(KE

YIN

1)(4

)

RY

/BY

(3)

ON

L(8

)C

RU

MS

DT

A(1

2)C

RU

MS

CL

(12)

PS

L(8

)

mt_

at_h

ome#

(4)

MC

NT

(5)

MC

U P

WB

(C

PU

sec

tio

n)

(AL

-203

0/20

40C

S)

Res

et C

ircu

it

AS

IC_R

ES

ET

TP

226

TP

253

TP

180

TP162TP139

C200.1u C200.1u

TP

201

C250.1u C250.1u

TP167

BR

8

10kJ

x4

1 2 3 4

8 7 6 5

R26

110

kJ

TP

222

TP

10

TP

242

TP172TP150

BR2233Jx4

1234

8765

BR

10

10kJ

x4

1 2 3 4

8 7 6 5

TP227

TP

185

TP163TP140

R4

*1

TP

254

TP

181

C26

47p

TP

202

TP

6TP168

BR2333Jx4

1234

8765

BR

3

10kJ

x4

1 2 3 4

8 7 6 5

TP

24

IC2

H8S

/232

1

HD

6412

321V

F25

(H8S

/232

1)

IC2

P35

/SC

K1

64

P34

/SC

K0

63

P33

/RxD

162

P32

/RxD

061

P31

/TxD

160

P30

/TxD

059

VC

C58

PD

7/D

1557

PD

6/D

1456

PD

5/D

1355

PD

4/D

1254

Vss

53

PD

3/D

1152

PD

2/D

1051

PD

1/D

950

PD

0/D

849

PE

7/D

748

PE

6/D

647

PE

5/D

546

PE

4/D

445

Vss

44

PE

3/D

343

PE

2/D

242

PE

1/D

141

PE

0/D

040

VC

C39

AV

cc10

3

Vre

f10

4

P40

/AN

010

5

P41

/AN

110

6

P42

/AN

210

7

P43

/AN

310

8

P44

/AN

410

9

P45

/AN

511

0

P46

/AN

6/D

A0

111

P47

/AN

7/D

A1

112

AV

ss11

3

Vss

114

P17

/PO

15/T

IOC

B2/

TC

LKD

115

P16

/PO

14/T

IOC

A2

116

P15

/PO

13/T

IOC

B1/

TC

LKC

117

P14

/PO

12/T

IOC

A1

118

P13

/PO

11/T

IOC

D0/

TC

LKB

119

P12

/PO

10/T

IOC

C0/

TC

LKA

120

P11

/PO

9/T

IOC

B0/

DA

CK

112

1

P10

/PO

8/T

IOC

A0/

DA

CK

012

2

MD

012

3

MD

112

4

MD

212

5

PG

0/C

AS

126

PG

1/C

S3

127

PG

2/C

S2

128

PG3/CS11

PG4/CS02

Vss3

NC4

VCC5

PC0/A06

PC1/A17

PC2/A28

PC3/A39

Vss10

PC4/A411

PC5/A512

PC6/A613

PC7/A714

PB0/A815

PB1/A916

PB2/A1017

PB3/A1118

Vss19

PB4/A1220

PB5/A1321

PB6/A1422

PB7/A1523

PA0/A1624

PA1/A1725

PA2/A1826

PA3/A1927

Vss28

PA4/A20/IRQ429

PA5/A21/IRQ530

PA6/A22/IRQ631

PA7/A23/IRQ732

P67/CS7/IRQ333

P66/CS6/IRQ234

Vss35

Vss36

P65/IRQ137

P64/IRQ038

P53/ADTRG102

P52/SCK2101

Vss100

Vss99

P51/RxD298

P50/TxD297

PF0/BREQ96

PF1/BACK95

PF2/LCAS/ WAIT/BREQO94

PF3/LWR93

PF4/HWR92

PF5/RD91

PF6/AS90

VCC89

PF7/088

Vss87

EXTAL86

XTAL85

VCC84

STBY83

NMI82

RES81

WDTOVF80

P20/PO0/TIOCA379

P21/PO1/YICOB378

P22/PO2/TIOCC377

P23/PO3/TIOCD376

P24/PO4/TIOCA475

P25/PO5/TIOCB474

P26/PO6/TIOCA573

P27/PO7/TIOCB572

P63/TEND171

P62/DREQ170

P61/TEND0/CS569

Vss68

Vss67

P60/DREQ0/CS466

Vss65

TP

261

TP151

TP

243

TP173

TP

245

TP

186

R25

22k

J

TP228

TP

182

BR2433Jx4

1234

8765

TP141

TP

154

TP

131

BR

6

10kJ

x4

1 2 3 4

8 7 6 5

TP

203

TP

8

TP

195

TP169

C2

0.1u

C160.1u

TP

25

BR2533Jx4

1234

8765

R17

10kJ

R12

33J

TP174

TP

246

TP152

TP

244

TP210

C4

100p

C4

100p

R26

210

kJ

TP142

TP229

TP

187

TP

183

TP

132

TP

204

TP

255

TP

155

BR2633Jx4

1234

8765

R8

*4

TP

196

BR

11

10kJ

x4

1234

8765

R25

010

kJ

TP170

R2

N.M

.N

.M.

R13

33J

TP

258

C1222pF

TP153

R24

810

kJ

TP175

TP247

TP143

TP

235

BR

1733

Jx4

1 2 3 4

8 7 6 5

TP211

TP

188

TP230 TP230

C14N.M.

TP

184

BR

7

10kJ

x4

1 2 3 4

8 7 6 5

TP156TP133

TP

205

C13N.M.

TP

256

TP

197

C6

12p

IC3 BU

4212

F

IC3 GN

D1

VD

D2

CT

3

VO

UT

4

C15N.M.

BR

1833

Jx4

1 2 3 4

8 7 6 5R1633J

R14

33J

BR

15

10kJ

x4

1 2 3 4

8 7 6 5

R22

10kJ

R26

310

kJ

TP

1

R24

610

kJ

TP

259

TP176

TP

248

R1

N.M

.

TP

126

TP212

TP144

TP

236

TP

231

R21

33J

TP

189

X1

HC

-49U

/S19

.660

8MH

z

TP

262

BR

1933

Jx4

1 2 3 4

8 7 6 5

TP

206

TP

257

TP157TP134

BR

12

10kJ

x4

1234

8765

TP

198

C210.1u C210.1u

TP

193

TP

30

R19

10kJ

TP

260

BR

2033

Jx4

1 2 3 4

8 7 6 5

TP7

TP

267

TP

127

TP

177

TP

2

C220.1u C220.1u

TP

237

TP213

R3

*2

TP145

R9

33J

BR

21

33Jx

4

1234

8765

TP

232

R5

N.M

.

TP

190

TP

263

TP158TP135

C230.1u C230.1u

TP

207

TP

199

C733p

R42

110

kJT

P19

4

C101uF

C240.1u C240.1u

R24

510

kJ(o

pen)

TP

31

C78

100p

TP

218

C17

0.01

uF

TP

250

+

C19

10u/

16V

+

C19

10u/

16V

TP

128

TP214

TP146

TP

238

TP

233

TP

191

TP223

R6

0J

TP159TP136

TP

208

C833p

R7

*3

C3

100p

C3

100p

C5

*5

TP164

C933p

BR

1

10kJ

x4

1 2 3 4

8 7 6 5

R25

12k

J

TP

32

L11

0J (

1608

)L1

10J

(16

08)

TP219

TP

129

TP

251

TP215

TP147

TP

239

TP

234

TP

192

BR

14

10kJ

x4

1 2 3 4

8 7 6 5

TP

224

R20

100k

J

TP137

TP

209

TP

249

TP

178

TP160

R24

9N

.M._

10kJ

TP165

R11

100J

TP

33

TP

220

L1 ZJS

R51

01-2

23(o

pen)

L1 ZJS

R51

01-2

23(o

pen)

TP

130

TP148

TP

240

TP216

BR

16

10kJ

x4

1234

8765

R18

33J

TP225

TP

179

TP161TP138

TP

252

R24

710

kJ

BR

2

10kJ

x4

1 2 3 4

8 7 6 5

TP

200

IC1

N.M

._C

Y25

811S

C

XIN

/CLK

IN1

XO

UT

8V

DD

7

VS

S2

SS

CLK

5F

RS

EL

6

S0

4

S1

3

C18

N.M

.

TP166

C1

*6

TP

125

TP221

TP

9

R10

33J

BR

5

10kJ

x4

1 2 3 4

8 7 6 5

TP171

TP217

TP149

TP

241

C11

N.M

.

1/13

AL-2030/2040CS/2050CS CIRCUIT DIAGRAM 13 - 1

PF

CLK

IN

PFCLKOUT

/INR

EQ

SY

NC

#

AF

E_D

B0

AF

E_D

B7

AF

E_D

B4

AF

E_D

B5

AF

E_D

B6

AF

E_D

B1

AF

E_D

B2

AF

E_D

B3

/OU

TA

CK

/PC

LPR

O/F

AX

PR

O/E

SP

RD

CLK

_CO

NT

/OU

TC

S

MM

_BI1

MM

_AI0

MM

_BI2

MM

_BI0

MM

_AI2

MM

_AI1

/AU

TO

FD

/SLC

TIN

/INIT

/ST

B

PA

RA

D7

PA

RA

D3

PA

RA

D4

PA

RA

D5

PA

RA

D6

PA

RA

D1

PA

RA

D2

PA

RA

D0

VM

IN

RC

VV

PIN

AF

E_D

B7

AF

E_D

B6

AF

E_D

B3

AF

E_D

B5

AF

E_D

B2

AF

E_D

B1

AF

E_D

B4

AF

E_D

B0

AF

E_S

DI

RA

MD

B0

RA

MD

B3

RA

MD

B2

RA

MD

B1

RA

MD

B5

RA

MD

B4

RA

MD

B7

RA

MD

B6

RA

MD

B12

RA

MD

B14

RA

MD

B15

RA

MD

B13

RA

MD

B8

RA

MD

B9

RA

MD

B10

RA

MD

B11

VM

IN

JTG

_TD

IJT

G_T

MS

JTG

_TC

K

PF

CLK

JTG

_TD

O

/PIR

EQ

/PO

AC

K

PO

DA

TA

3P

OD

AT

A2

PO

DA

TA

1P

OD

AT

A0

PO

DA

TA

7P

OD

AT

A6

PO

DA

TA

5P

OD

AT

A4

ME

M_I

NT

CLK

SW

CLK

_CO

NT

CLK

_CO

NT

SF

CLK

48

AF

E_S

DI

MT

AD

0M

TA

D1

MT

AD

2M

TA

D3

MT

AD

4M

TA

D5

MT

AD

6M

TA

D7

/AU

TO

FD

/SLC

TIN

/INITSLC

TP

EB

US

Y/A

CK

FA

ULT

/RE

V

PA

RA

D7

PA

RA

D6

PA

RA

D5

PA

RA

D4

PA

RA

D3

PA

RA

D2

PA

RA

D1

PA

RA

D0

MM

_BI0

MM

_AI0

MM

_AI1

MM

_AI2

PO

DA

TA

1

PIDATA4

MTAD1

/PCLPRO

A7

D1

/INREQ

A1

PF

CLK

OU

T

CLKSW

PO

DA

TA

0

/PIR

EQ

MTAD8

MTAD12

A5

D6

JTG_TMS

MTAD0

/OUTACK

A2

D0

D7

PO

DA

TA

3

SFCLK48

D10

D12

PIDATA0

MTAD7

MTAD11

A8

D5

D15

A6

VP

IN

PO

DA

TA

6

/PO

AC

K

/OUTCS

D14

PO

DA

TA

5

PO

DA

TA

2

PIDATA1

MTAD4

MTAD10SYNC#

JTG_TCK

JTG_TDI

PIDATA5

RAM_CLK_OUT

MTAD15

MM

_BI2

PFCLK

D9D8

PIDATA2

MTAD3

RC

V

JTG_TDO

PIDATA6

A3

A9

D2

MTAD5

MTAD14

MM

_BI1

PIDATA3

MTAD2

D3

D11

D13

PO

DA

TA

7

PO

DA

TA

4

PIDATA7

/ESPRD

MEM_INT

/ST

B

PFCLKIN

MTAD6

MTAD9

MTAD13

/FAXPRO

A4

D4

RA

M_C

LK_O

UT

MA

D3

MA

D2

MA

D1

MA

D0

MA

D10

MA

D12

MA

D11

MA

D9

MA

D8

MA

D7

MA

D6

MA

D5

MA

D4

RA

MD

B7

RA

MD

B6

RA

MD

B5

RA

MD

B4

RA

MD

B3

RA

MD

B2

RA

MD

B1

RA

MD

B0

RA

MD

B15

RA

MD

B14

RA

MD

B13

RA

MD

B12

RA

MD

B11

RA

MD

B10

RA

MD

B9

RA

MD

B8

MT

AD

8M

TA

D9

MT

AD

10M

TA

D11

MT

AD

12M

TA

D13

MT

AD

14M

TA

D15

PID

AT

A0

PID

AT

A1

PID

AT

A2

PID

AT

A3

PID

AT

A4

PID

AT

A5

PID

AT

A6

PID

AT

A7

G3.

3V

VC

C3

VC

C3

VC

C3

VC

C3

VC

C3

VC

C3

G3.

3V

VC

C3

VC

C3

VC

C3

VC

C3

VC

C3

VC

C3

VC

C3

VC

C3

VC

C3

VC

C3

VC

C3

MM

_Y2

(5)

/SD

WD

E(3

)

CC

D_C

P(4

)

HL

(5)

(/S

YN

C)

(4)

MRPS2 (5)

VFM_24V (5)

DQ

M1

(3)

/LWR (1)

TM

(4)

VFMCNT_12V (5)

MM

_Y1

(5)

/LEND (5)

CC

D_T

G(1

,4)

MC (5)

PR

(5)

/SC

AN

SP

(1)

BIAS (5)

MM

_PH

_B(6

)

VS

AM

P(4

)

RRS (5)

MP

FS

(5)

CPFS1 (5)

/SD

RA

S(3

)

MM

_Y3

(5)

CC

D_P

HI1

(4)

/CS2 (1)

/RD (1,3)

MMD (5)

SD

CLK

(3)

MM

_PH

_A(6

)

TM

_(4

)

VIDEO# (4)

TC (5)

MM

_BI0

(6)

AF

E_S

CK

(4)

D[1

5..0

](1

,3)

MIRCNT (4)

CC

D_P

HI2

(4)

PTPULSE (5)

/SD

CS

(3)

MM

_AI0

(6)

OP

_LA

TC

H(4

)

CL

(10)

MA

D[1

2..0

](3

)

BA

NK

0(3

)

MM

_BI1

(6)

LDEN (5)

/RESET0

(1,3,4)

A[2

0..0

](1

,3)

RA

MD

B[1

5..0

](3

)

CP

FS

2(5

)

/TR

AN

SS

T(1

)

SD

CK

E(3

)

AF

E_S

EN

(4)

MRPS3 (5)

MIR

ON

(4)

/ASIC_RST (1,4,12)

OP

_CLK

(4)

MRPS1 (5)

BS

AM

P(4

)

GRIDL (5)

SP

FO

N(4

)

MM

_AI1

(6)

DQ

M0

(3)

OP

_DA

TA

(4)

CC

D_R

S(4

)

PMD (5)

/SD

CA

S(3

)

AD

CLK

(4) A

FE

_DB

[7..0

](4

)

VP

OU

T(1

1)V

MO

UT

(11)

OE

N(1

1)

SU

SP

EN

D(1

1)

VM

IN(1

1)

/PR

INT

ST

(1)

VP

IN(1

1)R

CV

(11)

/SC

AN

ST

(1)

AF

E_S

DI

(4)

PO

FF

(1,5

)PA

RA

D[7

..0]

(13)

/RE

V(1

3)/F

AU

LT(1

3)

/AC

K(1

3)B

US

Y(1

3)P

E(1

3)S

LCT

(13)

/INIT

(13)

/SLC

TIN

(13)

/AU

TO

FD

(13)

/OA

_RS

T(1

3)

(/A

SIC

_RS

T)

(4)

/RE

SE

T1

(1,4

)

CPU_SYNC (1)

/ST

B(1

3)

ARB_INT (1)B

AN

K1

(3)

BR

3010

kJx4

1 2 3 4

8 7 6 5

TP

405

TP327

TP

338

TP274

TP

385

R24

33J

R24

33J

TP281

TP

352

TP

356

R29

33J

R29

33J

TP

388

C48

47p

TP

429

TP

112

1

TP

308

R51

10kJ

R51

10kJ

R50

N.M

.

TP80

1

TP110

1

C680.1u

TP

346

TP

34

C640.1uu

TP

377

C600.1u

TP

367

TP

37

1

BR

290J

x41 2 3 4

8 7 6 5

TP

302

TP96

1

TP335

TP275

R33

33J

R33

33J

TP

65

1

TP

47

1

TP

447

TP79

1

TP

406

TP109

1

R38

10kJ

TP282

TP328

BR

5310

kJx4

1 2 3 4

8 7 6 5

TP

389

R41

33J

TP

116

1

TP4

TP276T

P43

0

TP

339

TP

410

BR

4810

kJx4

1 2 3 4

8 7 6 5

C340.1u

C590.1u

BR

61

33Jx

4

1 2 3 4

8 7 6 5

TP

368

TP

399

TP95

1

TP

353

BR

60

33Jx

4

1 2 3 4

8 7 6 5

TP

311

R30

33J

R30

33J

TP78

1

R31

33J

R31

33J

TP

5

TP

73

1

TP

42

1

TP294

TP

378

TP

70

1

TP108

1

TP

39

1

TP

347

TP

121

1

TP

423

TP

303

C660.1u

BR

63

33Jx

4

1 2 3 4

8 7 6 5

TP336

TP

448

TP

432

TP

56

1

TP

407

TP

392

TP283TP94

1

TP

442

R32

33J

R32

33J

TP

54

1

C310.1u

TP

390

TP

58

1

BR

3433

Jx4

1 2 3 4

8 7 6 5

R36

333

J

TP

411

BR

6610

kJx4

1234

8765

TP279

BR

6710

kJx4

1234

8765

TP297

TP107

1

TP277

TP

431

C73N.M. .M.

TP

369 TP

400

TP

451

BR

4782

Jx4

1 2 3 4

8 7 6 5

TP

76

1

BR

4510

kJx4

1 2 3 4

8 7 6 5

C52

47p

TP

354

C25

6N

.M.

C55

47p

TP

340

TP

312

TP

379

TP93

1

TP295

TP

52

1

TP

60

1

R25

410

kJ

R37

5N

.M.

TP

436

BR

4310

kJx4

1 2 3 4

8 7 6 5

C430.1u

TP

424

R48

N.M

.R

48N

.M.

TP285

TP106

1

TP337

TP

393

BR

3633

Jx4

1 2 3 4

8 7 6 5

TP

45

1

R49

10kJ

R49

10kJ

TP

433

TP

67

1

TP

449

TP

443

TP284

R34

10K

JR

3410

KJ

R53

33J

33J

TP

391

TP

36

TP92

1

TP

412

TP280

R40

9N

.M._

10K

J

TP

370

TP

401

C670.1u

TP105

1

TP

355

BR

2810

kJx4

BR

2810

kJx4

1234

8765

TP

313

TP

357

C290.1u

TP296

BR

5210

kJx4

1 2 3 4

8 7 6 5

C270.1u

TP

360

TP

62

1

X3

SG

8002

DC

(18.

3856

MH

z)

N.C

.1

VC

C8

OU

TP

UT

5

GN

D4

TP

50

1

TP91

1

TP

341

TP

437

R23

33J

R23

33J

TP

425

C460.1u

TP286

BR

6810

kJx4

1234

8765

TP

434

TP

394

R23

6N

.M.

R37

4N

.M.

TP

120

1

TP104

1

TP

444

X2

SG

8002

DC

(48.

0000

MH

z)

N.C

.1

VC

C8

OU

TP

UT

5

GN

D4

C320.1u

TP

316

TP

413

TP

402

TP3

TP292

C280.1u

TP90

1

C300.1u

TP

314

TP

358

TP103

1

C50

47p

TP

40

1

C54

47p

TP

38

1

TP271

TP

371

BR

3533

Jx4

1 2 3 4

8 7 6 5

TP

361

TP

426

L12

N.M

.

TP268

C23

112

0p

TP

72

1

TP

438

TP77

1

TP

124

1

BR

5110

kJx4

1 2 3 4

8 7 6 5

R40

433

J

TP

435

TP329

R25

510

kJ

TP

395

R52

10J

TP

445

BR

62

33Jx

4

1 2 3 4

8 7 6 5

TP

380

TP89

1

C58

N.M

.

TP

48

1

TP

317

TP

64

1

TP

342

C25

747

p

BR

2710

kJx4

BR

2710

kJx4

1234

8765

TP102

1

TP288

BR

4033

Jx4

1 2 3 4

8 7 6 5

TP

414

TP

69

1

TP

43

1

BR

4133

Jx4

1 2 3 4

8 7 6 5

C23222000p

TP293

TP290

TP

75

1

TP

415

R25

610

kJ

TP

359

TP

452

TP

315

C350.1u

C630.1u

TP88

1

TP

372

TP

362

TP272

C470.1u

C49

47p

TP101

1

TP

439

TP

427

TP269

TP

396

BR

3910

kJx4

1 2 3 4

8 7 6 5

BR

4210

kJx4

1 2 3 4

8 7 6 5

TP330

BR

7110

kJx4

1 2 3 4

8 7 6 5

TP

381

TP323

TP

318

TP

348

R40

7N

.M.

TP

115

1

BR

5410

kJx4

1 2 3 4

8 7 6 5

TP87

1

TP289

TP

119

1

R47

33J

TP

304

TP

309

L2

ZJS

R51

01-2

23

BR

3733

Jx4

1 2 3 4

8 7 6 5

TP

416

C51

47p

TP291

TP100

1

R27

33J

R27

33J

TP

446

R28

10K

JR

2810

KJ

+C

37

47u/

16V

+

TP

343

C420.1u

C380.1u

TP

373

TP

363

C650.1u

C71N.M. .M.

TP86

1

TP

440

C330.1u

TP

66

1

TP331

TP

46

1

TP

397

C450.1u

TP324

C610.1u

TP

57

1

IC4

HG

73C

141H

FV

AS

IC

CPU_DATA71

CPU_DATA62

CPU_DATA53

CPU_DATA44

CPU_DATA18

CPU_DATA36

CPU_DATA27

VCC(AC)5

CPU_DATA09

GND(AC)10

MIRCNT11

/CPUSYNC12

MEM_INT13

ARB_INT14

VCC(CORE)15

CPU_AD816

CPU_AD717

CPU_AD618

CPU_AD519

GND(CORE)20

RAM_CLK_IN21

CPU_AD422

CPU_AD323

CPU_AD224

CPU_AD125

CPU_AD026

/CPUCS27

SFCLK4828

GND(CORE)29

/CPUWR30

/CPURD31

/RESET32

PFCLK34

CLKSW35

GND(CORE)36

PFCLKOUT37

PFCLKIN38

GND(PLL)39

VCC(PLL)40

GND(PLL)41

VCC(PLL)42

TM2_15M43

/SYNC44

GND(AC)45

/VIDEO46

/LEND47

VCC(AC)48

OUTP00A49

OUTP02A51

OUTP03A52

OUTP04A53

OUTP05A54

OUTP06A55

VCC(CORE)57OUTP15A56

OUTP07A58

OUTP08A59

GND(CORE)60

OUTP09A61

OUTP10A62

OUTP11A63

OUTP12A64

VC

C(C

OR

E)

86

OU

TP

13B

84

OU

TP

12B

83

OU

TP

10B

81

GND(AC)69

OU

TP

09B

80

OU

TP

08B

79

OUTP03B72

GN

D(C

OR

E)

78

OU

TP

07B

77

OU

TP

06B

76

OUTP00B68OUTP14A67VCC(CORE)66OUTP13A65

VCC(AC)74OUTP04B73

OU

TP

11B

82

OUTP02B71

OU

TP

05B

75

OU

TP

14B

85

OUTP01B70

TS

P_M

OD

E96

OP

E_C

LK92

/TM

87T

M88

OP

E_D

AT

A89

OP

E_L

AT

CH

90G

ND

(AC

)91

VC

C(A

C)

93/S

CA

NS

P94

TS

O0

95

IE12

84_S

TB

97IE

1284

_AU

TO

FD

98V

CC

(CO

RE

)99

IE12

84_S

LCT

IN10

0IE

1284

_IN

IT10

1IE

1284

_SLC

T10

2G

ND

(CO

RE

)10

3IE

1284

_PE

104

IE12

84_B

US

Y10

5IE

1284

_AC

K10

6IE

1284

_FA

ULT

107

VC

C(C

OR

E)

108

IE12

84_R

EV

109

IE12

84_P

AR

AD

711

0IE

1284

_PA

RA

D6

111

IE12

84_P

AR

AD

511

2IE

1284

_PA

RA

D4

113

IE12

84_P

AR

AD

311

4IE

1284

_PA

RA

D2

115

VC

C(A

C)

116

IE12

84_P

AR

AD

111

7IE

1284

_PA

RA

D0

118

SU

SP

EN

D11

9G

ND

(AC

)12

0O

EN

121

VM

OU

T12

2V

PO

UT

123

GN

D(C

OR

E)

124

VM

IN12

5V

PIN

126

RC

V12

7/S

CA

NS

T12

8

VCC(CORE)192

/INREQ191

/OUTCS190

/OUTACK189

/ESPRD188

/FAXPRD187

/PCLPRD186

GND(AC)185

MDAT15184

MDAT14183

MDAT13182

VCC(CORE)181

MDAT12180

MDAT11179

MDAT10178

VCC(AC)177

MDAT09176

MDAT08175

MDAT07174

GND(CORE)173

MDAT06172

MDAT05171

MDAT04170

VCC(CORE)169

MDAT03168

MDAT02167

MDAT01166

MDAT00165

GND(AC)164

/INCS163

/INACK162

/OUTREQ161

GND(CORE)160

/HSYNC159

PIDATA0158

PIDATA1157

PIDATA2156

VCC(AC)155

PIDATA3154

PIDATA4153

PIDATA5152

PIDATA6151

PIDATA7150

/POCS149

/PO

RE

Q14

8

VC

C(A

C)

147

/PIW

T14

6

/PIA

CK

145

GN

D(A

C)

144

/PO

AC

K14

3

/PIR

EQ

142

GN

D(C

OR

E)

141

PO

DA

TA

014

0

PO

DA

TA

113

9

PO

DA

TA

213

8

PO

DA

TA

313

7

PO

DA

TA

413

6

PO

DA

TA

513

5

PO

DA

TA

613

4

PO

DA

TA

713

3

VC

C(C

OR

E)

132

/TR

AN

SS

T13

1

/RE

CE

PT

ST

130

/PR

INT

ST

129

RA

M_D

AT

A4

256

RA

M_D

AT

A5

255

RA

M_D

AT

A6

254

RA

M_D

AT

A7

253

GN

D(A

C)

252

RA

M_D

QM

025

1R

AM

_WD

E25

0V

CC

(AC

)24

9R

AM

_CA

S24

8R

AM

_RA

S24

7R

AM

_CS

246

RA

M_B

AN

KS

024

5R

AM

_BA

NK

S1

244

VC

C(C

OR

E)

243

RA

M_M

AD

1024

2R

AM

_MA

D0

241

RA

M_M

AD

124

0G

ND

(CO

RE

)23

9R

AM

_MA

D2

238

RA

M_M

AD

323

7G

ND

(AC

)23

6M

M_A

I223

5M

M_A

I123

4M

M_A

I023

3M

M_P

H_A

232

AFE_DB3217

MM

_BI2

231

MM

_BI1

230

MM

_Y2

225

VCC(AC)221

MM

_Y1

226

AFE_DB0220

AFE_DB1219

GN

D(C

OR

E)

223

AFE_DB2218

AFE_DB4216

AFE_DB5215

MM

_BI0

229

MM

_PH

_B22

8V

CC

(CO

RE

)22

7

MM

_Y3

224

CLPWM222

AFE_DB6214

AFE_DB7213

GND(AC)212

AFESCK211

VCC(CORE)210

ADCLK209

GND(CORE)208

AFE_SEN207

CCD_PH1206

CCD_PH2205

AFE_SDI204

CCD_CP203

BSAMP202

CCD_RS201

CCD_TG200

VSAMP199

GND(CORE)198

TD0197

TRSK195 TDI196

TCK193 TMS194

VCC(CORE)33

OUTP01A50

GN

D(C

OR

E)

257

RA

M_D

AT

A3

258

RA

M_D

AT

A2

259

RA

M_D

AT

A1

260

RA

M_D

AT

A0

261

GN

D(A

C)

262

RA

M_D

AT

A15

263

RA

M_D

AT

A14

264

VC

C(C

OR

E)

265

RA

M_D

AT

A13

266

RA

M_D

AT

A12

267

RA

M_D

AT

A11

268

RA

M_D

AT

A10

269

RA

M_D

AT

A9

270

RA

M_D

AT

A8

271

VC

C(C

OR

E)

272

RA

M_D

QM

127

3

RA

M_C

KE

274

GN

D(A

C)

275

RA

M_C

LK_O

UT

276

GN

D(C

OR

E)

277

RA

M_M

AD

1227

8

RA

M_M

AD

1127

9

RA

M_M

AD

928

0

VC

C(C

OR

E)

281

RA

M_M

AD

828

2

RA

M_M

AD

728

3

VC

C(A

C)

284

RA

M_M

AD

628

5

RA

M_M

AD

528

6

RA

M_M

AD

428

7

GN

D(A

C)

288

CP

UD

AT

A15

289

CP

UD

AT

A14

290

CP

UD

AT

A13

291

CP

UD

AT

A12

292

CP

UD

AT

A11

293

CP

UD

AT

A10

294

CP

UD

AT

A9

295

CP

UD

AT

A8

296

TP

382

TP

55

1

TP99

1

TP

319

TP

349

TP

123

1

R26

33J

R26

33J

TP

310

BR

7010

kJx4

1 2 3 4

8 7 6 5

C26

410

00p

R35

33J

R35

33J

C74

N.M

.

TP

305

R40

333

J

R25

310

kJ

TP

59

1

BR

4433

Jx4

1 2 3 4

8 7 6 5TP85

1

TP

417

TP

53

1

TP

420

BR

4610

kJx4

1 2 3 4

8 7 6 5

TP287

R42

33J

TP98

1

TP

364

TP

374

TP

320

TP

441

R25

33J

R25

33J

TP

408

R45

N.M

.R

45N

.M.

TP

398

L10

0J (

1608

)

TP332

TP

344

TP

383

TP84

1

TP

403

TP325

BR

310J

x41 2 3 4

8 7 6 5

TP

71

1

C360.1u

TP

350

TP

41

1

TP

61

1

TP

51

1

TP97

1

TP

386

TP

306

TP

418

R39 10

kJ

TP

421

TP

450

C53

N.M

.

BR

5033

Jx4

1 2 3 4

8 7 6 5

TP

114

1

TP

298

R36

10kJ

BR

3210

kJx4

1 2 3 4

8 7 6 5

TP83

1

TP

74

1

BR

6910

kJx4

1234

8765

TP

118

1

R44

10kJ

TP278

C390.1u

C72N.M. .M.

TP

375

TP

321

BR

3310

kJx4

1 2 3 4

8 7 6 5

TP

365

R40

633

J

C79 47

p

C7522000p

TP

409

TP

113

1

BR

4933

Jx4

1 2 3 4

8 7 6 5

TP333

TP

117

1

R37

10kJ

C70N.M. .M.

TP

300

R40

33J

TP

404

TP326

TP273

TP

384

TP

351

TP

44

1

TP

68

1

TP82

1

TP

387

TP

345

C400.1u

R40

8N

.M.

C440.1u

TP

35

TP

428

TP

307

L13

0J (

1608

)

TP

49

1

TP

419

TP

63

1

TP

422

TP

299

TP

299

C690.1u

C410.1u

C77

82p

TP

122

1

C2300.1u

R43

33J

C76

0.1u

C56

N.M

.

TP

376

TP

322

TP

366

C57

47p

TP81

1

TP111

1

TP

301

TP334

C620.1u

5 5

4 4

3 3

2 2

1 1

DD

CC

BB

AA

MC

U P

WB

(G

rap

hic

_AS

IC s

ecti

on

) (A

L-2

030/

2040

CS

)2/

13


D6

/HW

R

RA

MD

B14

D7

A17

A4

RA

MD

B5

A8

MA

D9

/HW

R

MA

D1

A5

A2

A7

A14

MA

D6

D0

D2

D8

RA

MD

B9

RA

MD

B13

A15

A3

A2

RA

MD

B3

D15

MA

D8

VP

P

MA

D12

A8

A11

D13

D11

A15

VP

P

D3

D10

D14

A13

A19A13

RA

MD

B12

D10

RA

MD

B8

MA

D2

D14

RA

MD

B4

MA

D7

D15

MA

D11

A10

D9

A16

A18

D11

A12

MA

D3

A1

RA

MD

B11

D5

A16

RA

MD

B7

A1

A14

MA

D10

RA

MD

B2

D9

MA

D5

D8

RA

MD

B10

A7

A5

RA

MD

B0

A3

A9

D1

A1

A6

D12

RA

MD

B15

A10

A9

MA

D0

/RD

RA

MD

B6

A6

D4

MA

D4

RA

MD

B1

A12

A0

A4

A11

A17

D13

D12

A20

/RD

VC

C3

VC

C3

VC

C3

VC

C3

VC

C3

VC

C3

VC

C3

VC

C3

VC

C3

VC

C3

VC

C3

D[1

5..0

](1

,2)

RA

MD

B[1

5..0

](2

)

/CS

1(1

)

/CS

0(1

)

RY

/BY

(1)

/SD

CS

(2)/S

DR

AS

(2)

/RE

SE

T0

(1,2

,4)

MA

D[1

2..0

](2

)

/RD

(1,2

)

/SD

WD

E(2

)D

QM

0(2

)

BA

NK

0(2

)

SD

CLK

(2)

/HW

R(1

)

/SD

CA

S(2

)D

QM

1(2

)

SD

CK

E(2

)

BA

NK

1(2

)

A[2

0..0

](1

,2)

SC

L(1

)S

DA

(1)

Ser

ial E

E-P

RO

M

Fla

shR

OM

VP

P C

on

tro

ll

SD

RA

M

FL

AS

H R

OM

SR

AM

TP

453

C233N.M.

C234N.M.

C89

0.1u

IC7

Fla

sh R

OM

A0

25A

124

A2

23A

322

A4

21A

520

A6

19A

718

A8

8A

97

A10

6A

115

A12

4A

133

A14

2A

151

A16

48

A17

17

DQ

029

DQ

131

DQ

233

DQ

335

DQ

438

DQ

540

DQ

642

DQ

744

DQ

830

DQ

932

DQ

1034

DQ

1136

DQ

1239

DQ

1341

DQ

1443

DQ

1545

A19

9

NC

10

A18

16

GN

D46

GN

D27

VC

C37

VP

P13

BY

TE

47

OE

28

CE

26

WE

11

RP

12

WP

14

RY

/BY

15

R56

10kJ

R65N.M.T

P45

4

C90

0.1u

C91

0.1u

TP

458

C92

0.1u

C93

0.1u

TP

455

C81

0.1u

C84

0.1u

R64N.M.

C94

0.1u

R69

0J

R68

0J0J

R6310kJ

TP

456

C86N.M.

C236N.M.

C88

0.1u

R59

N.M

.

C235N.M.

IC5

24C

02/2

4WC

04/2

4WC

08

E0

1

E1

2

E2

3

VS

S4

SD

A5

SC

L6

WC

7V

CC

8

C82

N.M

.

C850.1u .1u

IC6

SD

RA

M (

16bi

t x 4

bank

)

A0

23

A1

24

A2

25

A3

26A

429

A5

30A

631

A7

32A

833

A9

34

A10

22

BA

020

DQ

02

DQ

14

DQ

25

DQ

37

DQ

48

DQ

510

DQ

611

DQ

713

DQ

842

DQ

944

DQ

1045

DQ

1147

DQ

1248

DQ

1350

DQ

1451

DQ

1553

VC

C1

VC

C27

VS

S54

VS

S28

VC

CQ

9

VS

S41

VC

CQ

43

VC

CQ

49V

SS

Q6

VS

SQ

12

VS

SQ

46

VS

SQ

52

LDQ

M15

UD

QM

39W

E16

CA

S17

RA

S18

CS

19C

LKE

37C

LK38

NC

40

NC

36

VC

CQ

3

VC

C14

BA

121

A11

35

R66

10kJ

R67

0J

J1,J

2

1 2 3

IC8

IS63

LV10

24L-

12J-

TR

IC8

I/O0

6A

01

I/O1

7A

12

I/O2

10A

23

I/O3

11A

34

I/O4

22A

413

I/O5

23A

514

I/O6

26A

615

I/O7

27A

716

A8

17

A9

18

A10

19

A11

20

A12

21

A13

29

A14

30

CS

15

OE

28

WE

12

VD

D8

GN

D9

VD

D24

A15

31

A16

32

GN

D25

R58

1kJ

TP

457

C83

0.1u

R62N.M. .M.

C87

0.1u

R70N.M.

5 5

4 4

3 3

2 2

1 1

DD

CC

BB

AA

MC

U P

WB

(M

emo

ry s

ecti

on

) (A

L-2

030/

2040

CS

)3/

13


/RE

SE

T#

VS

AM

P#

CC

D_T

G#

CC

D_R

S#

BS

AM

P#

CC

D_C

P#

CC

D_P

HI2

#C

CD

_PH

I1#

AD

CLK

#

PR

OT

EC

T

/RE

SE

T#

AF

E_S

DI#

AF

E_S

DI

AF

E_S

DI#

AF

E_S

DI

AF

E_D

B#0

AF

E_D

B#3

AF

E_D

B#2

AF

E_D

B#1

AF

E_D

B#7

AF

E_D

B#5

AF

E_D

B#4

AF

E_D

B#6 AF

E_D

B#0

AF

E_D

B#3

AF

E_D

B#2

AF

E_D

B#1

AF

E_D

B#7

AF

E_D

B#5

AF

E_D

B#4

AF

E_D

B#6

AF

E_D

B3

AF

E_D

B7

AF

E_D

B5

AF

E_D

B4

AF

E_D

B6

AF

E_D

B2

AF

E_D

B0

AF

E_D

B5

AF

E_D

B2

AF

E_D

B1

AF

E_D

B4

AF

E_D

B7

AF

E_D

B6

AF

E_D

B1

AF

E_D

B0

AF

E_D

B3

VS

AM

P#

BS

AM

P#

AD

CLK

#

CC

D_P

HI1

#

CC

D_P

HI2

#

CC

D_C

P#

CC

D_R

S#

CC

D_T

G#

VC

C3

5V

5V

5V

5V 5V 5V

VC

C3

5V

VC

C3

VC

C3

VC

C3

VC

C3

5V

5V

VC

C3

VC

C3

VC

C3

VC

C3

SE

LIN

3(1

)

(CE

D1)

(7)

SIN

2

OP

_LA

TC

H(2

)

KE

YIN

1(8

)

(PD

1)(7

)

(OP

_CLK

)(8

)

(SP

ID)

(7)

OP

_DA

TA

(2)

(FW

)(1

)

TM

_(2

)

(DR

ST

)(7

)

(TM

_)(6

)(T

M)

(6)

(PM

RD

Y)

(7)

/SY

NC

(9)

(CE

D2)

(7)

(OP

_LA

TC

H)

(8)

SE

LIN

2(1

)

(PO

D)

(7)

(PP

D3)

(7)

(PP

D2)

(7)

(TC

S)

(7)

(OP

_DA

TA

)(8

)

(SE

LIN

3)(8

)

(SE

LIN

1)(8

)

/VID

EO

(9)

SIN

1

SE

LIN

1(1

)

(PD

2)(7

)

DS

WS

(7)

/RE

SE

T1

(1,2

)

SIN

1S

IN2

OP

_CLK

(2)

SIN

3

(MF

D)

(7)

TH

OP

EN

(5)

(PP

D1)

(7)

(SE

LIN

2)(8

)

TM

(2)

VID

EO

#(2

)

(MM

LD)

(7)

SIN

3

DV

S1

(7)

FW

(8)

US

B_I

N(1

1)

KE

YIN

2(8

)(K

EY

IN1)

(1)

(KE

YIN

2)(1

)/R

ES

ET

0(1

,2,3

)

MIR

ON

(2)

SP

FM

T2/

MIR

CN

T(1

)(S

PF

MT

1)(6

)(S

PF

MT

0)(6

)

SP

FO

N(2

)

MIR

CN

T(2

)

(SP

FM

T2)

(6)

SP

FM

T0

(1)

(SP

FM

T3)

(6)

SP

FM

T3

(1)

SP

FM

T1

(1)

(/S

YN

C)

(2)(S

ELI

N2)

(8)

(SE

LIN

1)(8

)

(SE

LIN

3)(8

)

(US

B_I

N)

(1)

(SIN

1)(1

)

(SIN

3)(1

)(S

IN2)

(1)

D_C

ON

T(1

)(D

_CO

NT

)(1

1)

(FA

NLK

)(7

)

/AS

IC_R

ST

(1,2

,12)

(/A

SIC

_RS

T)

(2)

ST

RO

BE

(1)

(ST

RO

BE

)(8

)

mt_

at_h

ome

(10)

mt_

at_h

ome#

(1)

CC

D_C

P#

(10)

CC

D_T

G#

(10)

VS

AM

P#

(10)

CC

D_P

HI1

#(1

0)

AF

E_S

CK

#(1

0)

CC

D_P

HI2

#(1

0)

BS

AM

P#

(10)

CC

D_R

S#

(10)

AD

CLK

#(1

0)

AF

E_S

DI#

(10)

VS

AM

P(2

)C

CD

_TG

(1,2

)C

CD

_RS

(2)

BS

AM

P(2

)C

CD

_CP

(2) C

CD

_PH

I2(2

)C

CD

_PH

I1(2

)A

DC

LK(2

)

AF

E_S

DI

(2)

AF

E_S

EN

(2)

AF

E_S

CK

(2)

AF

E_S

EN

#(1

0)

AF

E_D

B#[

7..0

](1

0)A

FE

_DB

[7..0

](2

)

5V/3

.3V

3.3V

5V

3.3V

Dig

ital

Inp

ut

Mu

ltip

rexe

r

5V3.

3V

3.3V

3.3V

5V/3

.3V

3.3V

5V/3

.3V

3.3V

3.3V

3.3V

5V3.

3V

TP

472

R91

33J

BR

64

0Jx4

1 2 3 4

8 7 6 5

R12810kJ

TP

539

TP

498

C13

233

p

R88

33J

TP

523

R95

100J

R42

210

0J

TP

270

TP

270

C10

3

0.1u

TP

480

TP

492

C10

9

47p

R73

33J

33J

IC15

74V

HC

T24

4

1A1

2

1A2

4

1A3

6

1A4

8

2A1

11

2A2

13

2A3

15

2A4

17

1G1

2G19

1Y1

18

1Y2

16

1Y3

14

1Y4

12

2Y1

9

2Y2

7

2Y3

5

2Y4

3

VC

C20

GN

D10

BR

55

33Jx

4

BR

55

1234

8765

IC14

74LC

X24

4

1A1

2

1A2

4

1A3

6

1A4

8

2A1

11

2A2

13

2A3

15

2A4

17

1G1

2G19

1Y1

18

1Y2

16

1Y3

14

1Y4

12

2Y1

9

2Y2

7

2Y3

5

2Y4

3

VC

C20

GN

D10

IC13

74H

C15

1

D0

4

D1

3

D2

2

D3

1

D4

15

D5

14

D6

13

D7

12

A11

B10

C9

G7

W6

Y5

VC

C16

GN

D8

R86

10J

TP

473

R15

0JT

P46

3

C99

0.1u

C96

0.1u

TP

540

TP

499

TP

524

R10

033

J

R90

33J

C13

382

p

C10

4

33p

TP

503

R87

33J

TP

500

R74

10J

R80

10J

TP

533

IC45

NC

7ST

08M

5X

1 2 3

4

5

R81 10kJ1

C80

0.1u

TP

474

C10

0

33p

TP

507

R46

56J

TP

464

R13

00J

TP

541

TP

510

TP

496

TP

525

TP

11

TP

527

C97

33p

TP

513

IC9

74LC

X24

4

1A1

2

1A2

4

1A3

6

1A4

8

2A1

11

2A2

13

2A3

15

2A4

17

1G1

2G19

1Y1

18

1Y2

16

1Y3

14

1Y4

12

2Y1

9

2Y2

7

2Y3

5

2Y4

3

VC

C20

GN

D10

TP

493

TP

501

TP

482

R79

33J

R85

10kJ

TP

508

TP

475

TP

18

R20

50N

.M.

C10

882

p

R78

100J

TP

465

C10

2

N.M

.

TP

511

TP

526

TP

487

R54

56J

TP

528

R13

3op

en

TP

514

IC16

NC

7ST

08M

5X

1 2 3

4

5

TP

494

TP

483

R10

133

J

TP

497

TP

19

TP

509

TP

476TP

466

C12

482

p

TP

488

TP

529

TP

515

C26

3

0.1u

R55

100J

IC11

74LC

X24

4

IC11

1A1

2

1A2

4

1A3

6

1A4

8

2A1

11

2A2

13

2A3

15

2A4

17

1G1

2G19

1Y1

18

1Y2

16

1Y3

14

1Y4

12

2Y1

9

2Y2

7

2Y3

5

2Y4

3

VC

C20

GN

D10

TP

484

TP

495

IC12

74H

C15

1

D0

4

D1

3

D2

2

D3

1

D4

15

D5

14

D6

13

D7

12

A11

B10

C9

G7

W6

Y5

VC

C16

GN

D8

TP

467

TP

12

TP

534

TP

489

TP

505

TP

530

TP

516R

7633

J

C12

582

p

TP

485

TP

17T

P17

R57

56J

TP

468

C95

0.1u

TP

535

TP

531

R92

33J

TP

517

R83

47J

TP

544

C25

5

N.M

.

TP

486

C25

8

0.1u

(N.M

.)

R75

33J

C12

6N

.M.

R77

1kJ

IC10

74H

C15

1

D0

4

D1

3

D2

2

D3

1

D4

15

D5

14

D6

13

D7

12

A11

B10

C9

G7

W6

Y5

VC

C16

GN

D8

IC18

NC

7WZ

17

A1

1

A2

3

Y1

6

Y2

4

GN

D2

Vcc

5

R60

56J

C98

0.1u

C22

1

0.1u

BR

65 0Jx4

1234

8765

TP

469

TP

536

TP

520

TP

518

R98

N.M

.

TP

542

C10

1

0.01

uF

IC43

74LC

X24

4

1A1

2

1A2

4

1A3

6

1A4

8

2A1

11

2A2

13

2A3

15

2A4

17

1G1

2G19

1Y1

18

1Y2

16

1Y3

14

1Y4

12

2Y1

9

2Y2

7

2Y3

5

2Y4

3

VC

C20

GN

D10

C11

0

0.1u

C11

0

0.1u

C12

9N

.M.

C10

6

0.1u

IC35

NC

7WZ

17

A1

1

A2

3

Y1

6

Y2

4

GN

D2

Vcc

5

TP

502

TP

470

R61

100J C

262

0.1u

C10

50.

1u

TP

537

TP

521

TP

543

C10

7

0.1u

TP

519

R9610kJ

R71

33J

33J

R99

10kJ

TP

490

TP

477

TP

506

R9710kJ

C13

082

p

TP

471

R20

3010

kJ

R89

33J

R93

33J

R82

100J

TP

538

R94

33J

TP

522

R72

33J

33J

IC44

74LC

X24

4(op

en)

IC44

74LC

X24

4(op

en)

1A1

2

1A2

4

1A3

6

1A4

8

2A1

11

2A2

13

2A3

15

2A4

17

1G1

2G19

1Y1

18

1Y2

16

1Y3

14

1Y4

12

2Y1

9

2Y2

7

2Y3

5

2Y4

3

VC

C20

GN

D10

TP

491

TP

478

5 5

4 4

3 3

2 2

1 1

DD

CC

BB

AA

MC

U P

WB

(D

rive

r se

ctio

n 1

) (A

L-2

030/

2040

CS

)4/

13


/PR

PR

#

PR

#

VC

C3

VC

C3

24V

VC

C3

VC

C3

5V

12V

PG

ND

INT

5V

12V

PG

ND

VC

C3

12V

12V

12V

5V

24V

12V

5VV

CC

3

24V

12V

PG

ND

24V

PG

ND

5VV

CC

3

5V

VC

C3

VC

C3

12V

VC

C3

12V

12V

INT

24V

PG

ND

MM

ref0

(6)

/MC

(8)

/MP

FS

(9)

/GR

IDL

(8)

HL

(2)

LDE

N(2

)

MM

ref2

(6)

GR

IDL

(2)

MP

FS

(2)

BIA

S(2

)

CP

FS

1(2

)

MM

_Y2

(2)

VF

M_2

4V(2

)

/CP

FS

1(9

)

MM

_Y1

(2)

VF

MC

NT

_12V

(2)

PM

CLK

(1)

/TC

(8)

TC

(2)

MR

PS

2(2

)

RT

H(1

)

PR

(2)

MR

PS

_3(6

)

RT

H_I

N(9

)

/VF

MC

NT

(9)

/PM

D(9

)

MM

ref1

(6)

MR

PS

_2(6

)

PM

CLK

_A(9

)

FT

H

/RR

S(9

)

/BIA

S(8

)

SH

OLD

(9)

/MM

D(9

)

FT

H

VF

MO

UT

(9)

MM

_Y3

(2)M

RP

S1

(2)

/PO

FF

(8)

HLO

UT

(8)

TH

OP

EN

(4)

/LD

EN

(9)

CP

FS

2(2

)

MR

PS

_1(6

)

/LE

ND

(2)

MC

(2)

MM

D(2

)

/CP

FS

2(9

)

PM

D(2

)

MR

PS

3(2

)

TC

S_A

N(1

2)(T

CS

_AN

)(1

)

MC

NT

(1)

/MC

NT

(9)

/MM

CLK

(9)

MM

CLK

(1)

PO

FF

(1,2

)

RR

S(2

)

PT

PU

LSE

(2)

/PR

(8)

An

alo

g T

on

ner

Sen

sor

Bu

ffer

+ -

IC17

AK

IA39

3F

+ -

3 21

8 4

TP

21

R19

5

100J

TP

604

TP

612

TP

264

TP

547

Q18

KR

C10

2S

1

2

3

TP

559

R36

50J

TP

26

R38

847

kJ

R41

3N

.M._

10kJ

TP

479

R38

947

kJ

C13

4

1uF

/16V

IC19

KID

6500

1AF

1B1

2B2

3B3

4B4

5B5

6B6

7B7

E8

CO

M9

1C16

2C15

3C14

4C13

5C12

6C11

7C10

BR

7210

kJx4

1234

8765

TP

548

TP

560

TP

27

Q21

KR

C10

2S

1

2

3

TP

562

D2

KD

S22

6(op

en)

213

R11

710

kJR

117

10kJ

Q20

KR

A11

9S

1

2

3

D55

CR

H01

Q13

2SB

1132

B

E C

TP

549

TP

22

IC25

KID

6550

3F

1B1

2B2

3B3

4B4

5B5

6B6

7B7

G8

NC

9

1C16

2C15

3C14

4C13

5C12

6C11

7C10

TP

28

TP

561

+ -

IC20

BK

IA39

3F

+ -

5 67

8 4

R37

01.

5kJ

TP

617

R12

9N

.M.

R10

47.

5kF

R10

47.

5kF

Q2

N.M

._K

TA

1505

S

TP

555

R19

610

kJ

Q16

KR

C10

2S

1

2

3

R15

547

0kJ

TP

554

C16

02.

2uF

/10V

R36

4

0J

D49

MT

Z J

22B

R11

21.

2kF

CP

16

0603

FA

1.5A

/060

3SF

F15

0FM

R19

14.

7kJ

R10

74.

3kF

R10

74.

3kF

R10

9

N.M

._4.

7kJ

1/4

W

R14

61.

5kF

TP

265

R11

410

kF

D34

1SS

355

TP

618

R10

8

N.M

._47

kJ

TP

605

R19

310

kJ

IC24

KID

6550

3F

1B1

2B2

3B3

4B4

5B5

6B6

7B7

G8

NC

9

1C16

2C15

3C14

4C13

5C12

6C11

7C10

TP

551

TP

551

R38

0N

.M._

1.5k

J

TP

556

D35

1SS

355

D57

RLS

-73

D57

R38

6

4.7k

J 1/

4W

R14

447

kJ

R11

310

kJ

D1

MA

700

D1

R36

6N

.M.

R11

610

kJ

TP

619

TP

606

+ -

IC17

B

KIA

393F

+ -

5 67

8 4

C11

5

2200

0p

R10

31M

F

R11

030

0J

+ -

IC22

BK

IA35

8F

+ -

5 67

8 4

TP

557

Q17

KR

C10

2S

1

2

3

Q12

2SB

1132

B

E C

(G)

(D)

(S)

Q11

2SK

3018

(ope

n)(G)

(D)

(S)

R10

21k

F

R40

50J

R11

110

0J

D33

1SS

355

R36

7

10kJ

TP

620

D3

KD

S22

6

213

R41

4N

.M._

10kJ

C11

3

0.1u

C23

7

N.M

.

(G)

(D)

(S)

Q19

2SK

3018

(G)

(D)

(S)

TP

607

R13

810

kJC

162

0.1u

TP

558

R41

9N

.M._

10kJ

R10

610

kF

C11

222

000p

BR

561.

5kJx

41 2 3 4

8 7 6 5

R15

310

0J

R37

9N

.M._

1.5k

J

TP

624

TP

624

IC21

KID

6500

1AF

1B1

2B2

3B3

4B4

5B5

6B6

7B7

E8

CO

M9

1C16

2C15

3C14

4C13

5C12

6C11

7C10

D58

RLS

-73

R14

210

kJ(o

pen)

TP

608

TP

29

TP

266

R84

10kJ

BR

571.

5kJx

41 2 3 4

8 7 6 5

TP

621

TP

613

TP

613

C11

1

0.1u

/50V

+ -

IC22

AK

IA35

8F

+ -

3 21

8 4

D56

CR

H01D

56

CP

17

0603

FA

1.5A

/060

3SF

F15

0FM

TP

609

C11

4

0.1u

/50V

+ -

IC20

AK

IA39

3F

+ -

3 21

8 4

TP

610

TP

545

D46

KD

S22

6(op

en)

213T

P62

2

D4

1SS

355

TP

614

D5

1SS

355

D47

KD

S22

6(op

en)

213

Q14

KR

C10

2S

1

2

3

Q3

KR

A11

9S

1

2

3

R38

7

4.7k

J 1/

4W

TP

603

R41

8N

.M._

10kJ

TP

611

R10

51k

J

R19

210

kJ

TP

546

TP

623

Q4

KR

C10

2S

1

2

3

TP

23

TP

615

R11

510

0J 1

/4W

R19

4

100J

5 5

4 4

3 3

2 2

1 1

DD

CC

BB

AA

MC

U P

WB

(D

rive

r se

ctio

n 2

) (A

L-2

030/

2040

CS

)5/

13


PG

ND

PG

ND

5V

24V

SP

FM

T

24V

Dup

MT

PG

ND

PG

ND

24V

PG

ND

PG

ND

24V

SC

MT

PG

ND

PG

ND

PG

ND

PG

ND

24V

SC

MT

PG

ND

5V

24V

Dup

MT

5V

5V

PG

ND

PG

ND

5V

PG

ND

24V

SP

FM

T

24V

OU

T_A

-(9

)

TM

B_O

(9)

(SP

FM

T1)

(4)

SP

MT

_3(9

)

MM

ref2

(5)O

UT

_B+

(9)

(TM

)(4

)

(SP

FM

T3)

(4)

TM

A_O

(9)

MM

_BI0

(2)

MM

_AI0

(2)

(SP

FM

T0)

(4)

MM

_PH

_A(2

)M

M_A

I1(2

)

/DM

T3

(9)

OU

T_B

-(9

)

(SP

FM

T2)

(4)

(TM

_)(4

)

OU

T_A

+(9

)

SP

MT

_2(9

)

MM

ref1

(5)

DM

T1

(1)

DM

T0

(1)

/DM

T2

(9)

DM

T2

(1)

MM

ref0

(5)

MM

_PH

_B(2

)

SP

MT

_1(9

)

/DM

T1

(9)

DM

T3

(1)

/DM

T0

(9)

MM

_BI1

(2)

MR

PS

_3(5

)M

RP

S_2

(5)

MR

PS

_1(5

)

SP

MT

_0(9

)

Sca

nn

er M

oto

r D

rive

r

SP

F M

oto

r D

rive

r

Du

ple

x M

oto

r D

riv

er

To

nn

er

Mo

tor

Dri

ve

r

Fo

r A

L20

40 M

od

el O

nly

R13

562

0JJ

TP

597

TP

595

C12

8

0.1u

/50V V

R13

61.

2kJ

R12

01.

5kJ

R13

710

0JJ

R11

8

0.68

J 1W

TP

586

TP

596

R13

11.

2kJ

C11

682

0pp

C22

2

0.1u

R12

11.

5kJ

R12

330

kJ

C12

10.

1uC

121

0.1u

R11

9

0.68

J 1W

C11

882

0pp

R12

21k

JR

122

1kJ

IC26

TD

6206

4AF

IC26

TD

6206

4AF

I13

NC

4

NC

5

I26

NC

10

I311

NC

12

NC

13

GN

D17

O1

2

O2

7

O3

9

O4

16

CO

M1

CO

M8

GN

D18

I414

NC

15

R12

430

kJ

C11

782

0pp

C11

982

0p

BR

59

10kJ

x4

1234

8765

+C

122

47u/

35V

+

IC29

TA

7291

AS

Vcc

2

IN1

9

IN2

1

GN

D5

OU

T2

3

OU

T1

7

Vre

f8

Vs

6

N.C

4

D6

MT

Z J

22B

D6

MT

Z J

22B

R12

751

0JJ

C13

1

0.1u

R13

21J

2W

R12

61k

JC

120

0.1u

R12

52k

J

C12

30.

1u/5

0VV

IC28

ST

A71

00M MO

UT

A1

OU

T A

2

OU

T A

/3

OU

T A

/4

Vs

13

OU

T B

17

OU

T B

18

OU

T B

/15

OU

T B

/16

GN

D10

IN A

8

IN A

/7

IN B

11

IN B

/12

RE

F9

Sen

se A

5

Sen

se B

14

Syn

c6

+C

127

10u/

35V

+

TP

593

CP

106

03F

A1.

5A/0

603S

FF

150F

M

IC27

L621

9DS

OU

T 2

A2

SE

NS

E 2

3

CO

MP

24

OU

T 2

B5

GN

D6

GN

D7

I02

8

I12

9

PH

AS

E 2

10

VR

EF

211

RC

212

VS

S13

RC

114

VR

EF

115

PH

AS

E 1

16I1

117

GN

D18

GN

D19

I01

20O

UT

1B

21C

OM

P 1

22S

EN

SE

123

VS

24O

UT

1A

1

TP

587

R24

44.

7kJ

TP

590

R13

430

0JJ

R14

11J

2W

TP

588

TP

591

TP

589

CP

206

03F

A1.

5A/0

603S

FF

150F

M

TP

592

TP

594

CP

306

03F

A1.

5A/0

603S

FF

150F

M

5 5

4 4

3 3

2 2

1 1

DD

CC

BB

AA

MC

U P

WB

(D

rive

r se

ctio

n 3

) (A

L-2

030/

2040

CS

)6/

13


VC

C3

5V

INT

5V

PG

ND

VC

C3

EN

5V

VC

C3

5V

PG

ND

12V

5V

24V

VC

C3

INT

24V

INT

24V

5V 5V5V5V

PG

ND

5V

VC

C3

(PD

2)(4

)

DV

SE

L(1

2)

(DR

ST

)(4

)D

RS

T(8

)

PD

2(9

)

(PP

D3)

(4)

(CE

D1)

(4)

(TC

S)

(4)

(MM

LD)

(4)

PP

D1

(9)

(PP

D1)

(4)

TC

S(1

2)

PS

W(8

)

(CE

D2)

(4)

CE

D1

(9)

(SP

PD

)(1

)

CE

D2

(9)

PP

D3

(9)

(PP

D2)

(4)

(PM

RD

Y)

(4)

(PO

D)

(4)

12V

IN(8

)

DV

S1

(4)

PM

RD

Y(9

)

SP

PD

(9)

MF

D(9

)(M

FD

)(4

)

PO

D(9

)

PD

1(9

)(P

D1)

(4)

PP

D2

(9)

SP

ID(9

)

3.3V

IN(8

)

(PS

W)

(1)

MM

LD(9

)

(SP

ID)

(4)

DS

WS

(4)

24V

1(D

SW

S)

(9)

(FA

NLK

)(4

)F

AN

LK(9

)

R16

01k

J

L15

N.M

.

R16

615

kJ

R14

3

0.22

J 2W

R39

810

0kJ

R17

812

kJ

C17

9

0.1u

R37

710

kJ

C15

3

0.1u

R16

710

kJ

D14

KD

S22

6

213

R17

93.

3kJ

C22

4

1000

p

C17

1

1000

p

R37

81k

J

C15

4

0.1u

D15

KD

S22

6(op

en)

213

R14

74.

7kJ

R14

74.

7kJ

R17

57.

5kJ

C16

4

1000

p

C17

2

1000

p

D16

KD

S22

6(op

en)

213

R17

67.

5kJ

C15

5

0.1u

C16

8

0.1u

R15

21k

J 2W

C17

3

1000

p

R39

910

0kJ

C18

6

1000

p

C22

3

1000

p

R17

210

0J 2

W

C13

5

0.1u

C15

6

0.1u

C18

9

1000

p

C22

6

1000

p

R18

01k

J

C19

0

1000

p

D18

KD

S22

6

213

TP

151

D52

ZENER_UDZS4.7B(open)

C15

7

0.1u

R18

11k

J

+C

181

22u/

16V

+

R39

410

0kJ

C13

6

N.M

.

C18

7

1000

p

D20

1SS

355

D19

KD

S22

6(op

en)

213

D10

KD

S22

6(op

en)

213

C16

3

1000

p

IC30

KIA

7805

IN1

GN

D

2OU

T3

C18

3

0.1u

R18

21k

J

C15

8

0.1u

C18

8

1000

p

D21

KD

S22

6

213

D17

KD

S22

6(op

en)

213

D9

KD

S22

6(op

en)

213

R24

210

J

C18

4

0.1u

R18

31k

J

D13

KD

S22

6

213

D22

KD

S22

6(op

en)

213

C15

9

N.M

.

C13

7

0.1u

R14

910

kJR

149

10kJ

R14

515

kJR

145

15kJ

C17

6

0.1u

+C

182

22u/

16V

+

R24

010

J

R18

41k

J

C14

6

N.M

.

D51

ZENER_UDZS4.7B(open)

R16

81k

J

+C

175

47u/

35V

+

C16

1

1000

p

C18

0

0.1u

R18

51k

J

C14

7

N.M

.

R16

91k

J

C13

8

0.1u

C16

7

1000

p

L5 ZJS

R51

01-2

23

R18

61k

J

R14

810

kJR

148

10kJ

L14

0J (

1608

)

R17

01k

J

+C

178

22u/

16V

+

R17

77.

5kJ

C14

8

N.M

.

D12 1S

S35

5

C14

0

N.M

.

C13

9

N.M

.

R17

11k

J

TP

161

D11

1SS

355

C14

9

0.1u

C24

8

1000

p

C24

8

1000

p

C14

1

N.M

.

C22

5

1000

p

TP

585

C18

5

1000

p

C15

0

0.1u

C14

2

N.M

.

D27

KD

S22

6(op

en)

213

R15

91k

J

R17

315

kJ

R15

41k

J

C16

6

1000

p

D28

KD

S22

6(op

en)

213

C14

3

N.M

.

D25

KD

S22

6(op

en)

213

+C

169

47u/

35V

+

R39

6

100k

J

+C

177

47u/

25V

+

R24

110

J

D23

KD

S22

6(op

en)

213

C14

4

N.M

.

R15

110

kJR

151

10kJ

C17

0

0.1u

/50V

R15

61k

J

TP

131

D26

KD

S22

6

213

L4 ZJS

R51

01-2

23(o

pen)

D50

KD

S22

6(op

en)

213

C14

5

N.M

.

D29

KD

S22

6(op

en)

213

R16

32.

7kJ

R15

71k

J

D24

KD

S22

6(op

en)

213

R39

710

0kJ

C15

1

0.1u

R16

410

kJ

R16

120

kJC

165

1000

p

TP

141

R24

310

J

R15

81k

J

R16

510

kJ

R16

220

kJ

R15

015

kJR

150

15kJ

C15

2

0.1u

R17

415

kJ

5 5

4 4

3 3

2 2

1 1

DD

CC

BB

AA

MC

U P

WB

(N

ois

e fi

lter

/Pu

ll-u

p s

ecti

on

) (A

L-2

030/

2040

CS

)7/

13


KE

YIN

2#

KE

YIN

1#

KE

YIN

2#K

EY

IN1#

EN

5V

24V

INT

24V

PG

ND

5V

INT

5V

PG

ND

5V

5VE

N5V

PG

ND

HLO

UT

(5)

/PR

(5)

/MC

(5)

/BIA

S(5

)/T

C(5

)

12V

IN(7

)

3.3V

IN(7

)

/GR

IDL

(5)

FW

(4)

/PO

FF

(5)

PS

L(1

)

(SE

LIN

2)(4

)

KE

YIN

1(4

)

(OP

_DA

TA

)(4

)

(SE

LIN

3)(4

)

KE

YIN

2(4

)

PS

W(7

)

ON

L(1

)

(OP

_CLK

)(4

)(S

ELI

N1)

(4)

(OP

_LA

TC

H)

(4)

(ST

RO

BE

)(4

)

DR

ST

(7)

To

Op

erat

ion

al P

WB

To

Po

wer

un

it

R19

01k

J

C193

0.1u/50V

D31

KD

S22

6(op

en)

213

R40

0N

.M._

1608

size

C19

5

1000

p

C19

5

1000

p

CN

2

IMS

A-9

619S

-18A

123456789101112131415161718

R18

710

kJ

Q5

KR

C10

6SQ

5K

RC

106S

1

2

3

C194

N.M._1608size

Q6

KR

C10

6SQ

6K

RC

106S

1

2

3

CP7

0603FA1.5A/0603SFF150FM

CN

1

B24

B-P

ND

ZS

-1

1 3 5 7 9 11 13 15 17 19 21 23

2 4 6 8 10 12 14 16 18 20 22 24

D30

KD

S22

6(op

en)

213

R18

810

kJ

C19

1

1000

p

C19

2

1000

p

CP8

0603FA1.5A/0603SFF150FM

R18

91k

J

5 5

4 4

3 3

2 2

1 1

DD

CC

BB

AA

MC

U P

WB

(C

on

nec

tor

sect

ion

1)

(AL

-203

0/20

40C

S)

8/13


24V

PG

ND

5V5V

24VPG

ND

5V

24V

24V

SP

FM

T

24V

5V

5V

5V

VC

C3

5V

PG

ND

24V

INT

24V

PG

ND

24V

Dup

MT

24V

PG

ND

24V

5V

24V

PG

ND

INT

5V

5V

/VF

MC

NT

(5)

TM

B_O

(6)

/RR

S(5

)

PD

1(7

)

/DM

T1

(6)/C

PF

S1

(5)

24V

1(D

SW

S)

(7)

/MP

FS

(5)

SP

ID(7

)

PP

D1

(7)

VF

MO

UT

(5)

TM

A_O

(6)

PO

D(7

)

/DM

T0

(6)

SP

MT

_1(6

)

/DM

T3

(6)

PP

D2

(7) RT

H_I

N(5

)

MF

D(7

)

SP

PD

(7)

CE

D1

(7) /D

MT

2(6

)

SP

MT

_3(6

)

TxD

(1)

PD

2(7

)PP

D3

(7)

CE

D2

(7)/C

PF

S2

(5)

OU

T_B

+(6

)O

UT

_A-

(6)

OU

T_B

-(6

)

OU

T_A

+(6

)

/MM

D(5

)M

MLD

(7) /M

MC

LK(5

)

/MC

NT

(5)

FA

NLK

(7)

RxD

(1)

/PM

D(5

)

PM

CLK

_A(5

)P

MR

DY

(7)

/SY

NC

(4)

/LD

EN

(5)

/VID

EO

(4)

SH

OLD

(5)

SP

MT

_0(6

)S

PM

T_2

(6)

(Wh

ite)

(Wh

ite)

To

SP

F u

nit

(Fo

r d

ebu

g)

To

Pap

er d

etec

t

(Red

)

CP

U S

eria

l

(Wh

ite)

(Blu

e)

To

Cas

sett

e p

aper

so

len

oid

(Wh

ite)

(Wh

ite)

Not m

ou

nted

To

Po

lyg

on

mo

tor

To

Pap

er p

ass

det

ect

To

Fan

mo

tor

To

HL

un

it

(Bla

ck)

To

Cas

sett

e d

etec

t

(Red

)

To

To

ner

mo

tor

(Red

)

To

Du

ple

x m

oto

r

To

Inte

rlo

ck s

wit

ch

To

Mu

lti u

nit

To

Pap

er o

ut

det

ect

To

Res

ist

rolle

r so

len

oid

To

2n

d. c

asse

tte

To

Mir

ror

mo

tor

To

Mai

n m

oto

rT

o M

ech

a. C

OU

NT

ER

(Red

)

(Red

)

Fo

r A

L20

40 M

od

el O

nly

Fo

r A

L20

40 M

od

el O

nly

(Gre

en)

To

LD

(Wh

ite)

CN

18

B14

B-P

HD

SS

-B

1 3 5 7 9 11 13

2 4 6 8 10 12 14

CN

10

B3B

-PH

-K-S

1 2 3

CN

12

B3B

-PH

-K-E

1 2 3

R140

200J 1/4W

CN

16

B3B

-PH

-K-R

1 2 3

R20

820

0J 1

/4W

CN

19

B3B

-PH

-K-S

1 2 3

CN

17

N.M

._B

4B-P

H-K

-S

1 2 3 4

CN

6

B5B

-PA

SK

-1

1 2 3 4 5

CN

13

B05

B-X

AS

K-1

1 2 3 4 5

CN

7

B3B

-PH

-K-K

1 2 3

R20

520

0J 1

/4W

R20

320

0J 1

/4W

C20

1

1000

p

R20

420

0J 1

/4W

C20

0

1000

p

C19

9

1000

p

CN

25

B3B

-PH

-K-M

1 2 3

C2050.1u/50V

C2060.1u/50V

D42

KD

S22

6

213

CN

24

B12

B-P

H-K

-S

1 2 3 4 5 6 7 8 9 10 11 12

C19

8

1000

p

C2021000p

CN

11

B4B

-PH

-K-S

1 2 3 4

C2031000p

CN

15

B2P

-VH

-R

1 2

CN

28

N.M

._B

03B

-PH

-K-R

123

C2041000p

C246N.M.

CN

23

B2P

-VH

1 2

R207

200J 1/4W

CN

22

B5B

-PH

-K-S

1 2 3 4 5

CN

41

B05

B-C

ZH

K-B

1 2 3 4 5

CN

26

B5B

-PH

-K-R

1 2 3 4 5

C247

N.M._1608size

CN

4

B4B

-PH

-K-R

1 2 3 4

R20

61k

J

CN

42

B08

B-C

ZH

K-B

1 2 3 4 5 6 7 8

5 5

4 4

3 3

2 2

1 1

DD

CC

BB

AA

MC

U P

WB

(C

on

nec

tor

sect

ion

2)

(AL

-203

0/20

40C

S)

9/13


AF

E_D

B#0

AF

E_D

B#6

AF

E_D

B#6

VC

L

AF

E_D

B#4

AF

E_D

B#0

AF

E_D

B#7

AF

E_D

B#3

VC

L

AF

E_D

B#7

AF

E_D

B#5

AF

E_D

B#1

VC

L

AF

E_D

B#4

AF

E_D

B#2

AF

E_D

B#5

AF

E_D

B#3

AF

E_D

B#2

AF

E_D

B#1

PG

ND

PG

ND

VC

C3

PG

ND

24V

12V

EN

5V

CL

(2)

AF

E_S

DI#

(4)

CC

D_C

P#

(4)C

CD

_PH

I1#

(4)

VS

AM

P#

(4)

BS

AM

P#

(4)

AD

CLK

#(4

)

mt_

at_h

ome

(4)

AF

E_S

EN

#(4

)

CC

D_T

G#

(4)

CC

D_R

S#

(4)C

CD

_PH

I2#

(4)

AF

E_S

CK

#(4

) AF

E_D

B#[

7..0

](4

)

To

Sca

nn

er u

nit

Co

py

Lam

p In

vert

er

R20

991

0J

C20

9

0.1u

/50V

R21

31k

J

CN

3

FF

4-32

-S15

D5

135791113151719212325272931

2468101214161820222426283032

R212

5.6kJ 1/4W

CP

9

0603

FA

1.5A

/060

3SF

F15

0FM

+C

208

47u/

35V

+D

4411

EQ

S06

L6 220u

H

TW

KA

-221

K

R21

415

kJ

Q9

2SJ5

37

R21

556

kJ

C21

033

p

Q8

KT

C31

98

R21

015

kJ

CP

606

03F

A1.

5A/0

603S

FF

150F

M

R21

112

kJ

C21

1

1000

p

D43

KD

S22

6

213

CP

1006

03F

A1.

5A/0

603S

FF

150F

M

+C

207

47u/

35V

+

5 5

4 4

3 3

2 2

1 1

DD

CC

BB

AA

MC

U P

WB

(S

can

ner

I/F

sec

tio

n)

(AL

-203

0/20

40C

S)

10/1

3


VC

C3

VC

C3

VP

OU

T(2

)V

MO

UT

(2)US

B_I

N(4

)

OE

N(2

) VP

IN(2

)V

MIN

(2)

RC

V(2

)

SU

SP

EN

D(2

)

(D_C

ON

T)

(4)

F.G

C21

7

N.M

.

L7B

LM18

BB

121S

N1D

TP

567

IC31

US

B1T

20

IC31

MO

DE

1

OE

#2

RC

V3

VP

4

VM

5

SU

SP

EN

D6

GN

D7

NC

8

SP

EE

D9

D-

10D

+11

VP

O12

VM

O/F

SE

O13

VC

C14

D32

HZ

M6.

2Z4M

WA

(ope

n)

TP

568

C21

5

N.M

.

C21

2

100p

TP

569

R21

7

10kJ

R42

0N

.M.

TP

570

D45 ZE

NE

R_6

.2V

TP

571

L9 0J (

1608

)

L8B

LM18

BB

121S

N1D

R22

024

J

R21

624

J

TP

563

CN

33

UB

S21

-4K

2J00

(AC

ON

)

+5V

1

D-

2

D+

3

GN

D4

Shi

eld

L16

0J (

1608

)

C21

3

0.1u

R21

8

1.5k

J

TP

564

R22

133

JR

222

24J

TP

565

R22

333

J

C21

6

N.M

.

C21

4

0.1u

TP

566

R21

9N

.M.

R22

433

J

5 5

4 4

3 3

2 2

1 1

DD

CC

BB

AA

MC

U P

WB

(U

SB

2.0

(FU

LL

) I/F

sec

tio

n)

(AL

-203

0/20

40C

S)

11/1

3


EN

5V

EN

5V

VC

C3

24V

EN

5V

24V

PG

ND

/AS

IC_R

ST

(1,2

,4)

(CR

UM

SC

L)C

RU

MS

CL

(1)

(CR

UM

SD

TA

)C

RU

MS

DT

A(1

)

(CR

UM

SC

L)

TC

S(7

) DV

SE

L(7

)

(CR

UM

SD

TA

)

TC

S_A

N(5

)

5V

5V

3.3V

3.3V

CR

UM

Co

ntr

ol

(Wh

ite)

To

DV

Un

it w

ith

CR

UM

(An

alo

g T

on

ner

Sen

sor)

(Red

)

To

DV

Un

it(A

nal

og

To

nn

er S

enso

r)

F-G

ND

3

F-G

ND

4

F-G

ND

2

F-G

ND

1

TP

575

N.M

._B

10B

-PH

DS

S-B

CN

9

1 3 5 7 9

2 4 6 8 10

R20

010

JR

200

10J

D40

KD

S22

6

213

R36

90J

C22

0

0.1u

R13

91k

J

FB

1

0J (

1608

)

FB

1

0J (

1608

)

R23

10J

R23

210

kJ(o

pen)

IC32

TC

7SB

D38

5AF

U(o

pen)

A1

B2

OE

4G

ND

3

Vcc

5

R37

6N

.M.

TP

574

R20

2N

.M._

300J

TP

576

FB

4

0J (

1608

)

FB

4

0J (

1608

)

CN

5

B4B

-PH

-K-R

1 2 3 4

D39

KD

S22

6

213

IC34

NC

7ST

08M

5X(o

pen)

1 2 3

4

5

FB

2

0J (

1608

)

FB

2

0J (

1608

)

R22

5N

.M.

TP

573

TP

572

R22

610

kJ

C21

80.

1u

R36

8N

.M.

R20

1N

.M._

300J

FB

3

0J (

1608

)

FB

3

0J (

1608

)

5 5

4 4

3 3

2 2

1 1

DD

CC

BB

AA

MC

U P

WB

(C

RU

M I/

F s

ecti

on

) (A

L-2

030/

2040

CS

)12

/13


/ST

B

PA

RA

D7

PA

RA

D6

/INIT

/AC

KB

US

Y

/FA

ULT

PA

RA

D1

SLC

T

PA

RA

D2

PA

RA

D3

/RE

V

PA

RA

D4

/SLC

TIN

PA

RA

D5

/AU

TO

FD

PE

PA

RA

D0

VC

C3

EN

5V

EN

5VV

CC

3

/OA

_RS

T(2

)

PA

RA

D[7

..0]

(2)

/RE

V(2

)/IN

IT(2

)/SLC

TIN

(2)

/AU

TO

FD

(2)

/ST

B(2

)/FA

ULT

(2)

SLC

T(2

)P

E(2

)B

US

Y(2

)/A

CK

(2)

To

NIC

PW

B

Fo

r A

L20

40 M

od

el O

nly

C25

3

0.1u

CP12

0603FA1.5A/0603SFF150FM

C25

4

0.1u

CP11

0603FA1.5A/0603SFF150FM

CN

39

24F

MN

-BT

K-A

123456789101112131415161718192021222324

R40

2N

.M.

R40

11k

J

C25

1

0.1u

C25

2

0.1u

TP

459

TP

462

TP

460

TP

461

A A

B B

C C

D D

E E

44

33

22

11

MC

U P

WB

(N

IC In

terf

ace

sect

ion

) (A

L-2

030/

2040

CS

)13

/13


2. OPERATION PWB (AL-2030/2040CS)

DR

ST

D-G

ND

ON

L

SE

LIN

1

D-G

ND

KIN

1

SE

LIN

3

OP

-ST

B

KIN

2

5VDR

ST

PS

W

SE

LIN

2

OP

-CLK

OP

-DA

TA

5VE

NP

SL

D-G

ND

D-G

ND

DR

ST

D-G

ND

KIN

1

KIN

2

SE

LIN

3

SE

LIN

2

SE

LIN

1

PS

W

5VD-G

ND

D-G

ND

OP

-ST

B

OP

-CLK

OP

-DA

TA

PS

LO

NL

5VE

N

OP

-LA

TC

H

OP

-LA

TC

H

+5V

+5V

+5V

+5V

+5V

+5V

+5V

+5V

+5V

+5V

+5V

5VE

N

ON

LP

SL

ON

LP

SL

5VE

N

LEDM

f1

e1

a1

g1

d1

b1

c1

a2

g2

d2

f2

e2

b2

c2

a3

g3

d3

e3

b3

c3

LEDM

f3

DU

22A

EM

PL

PE

ME

ZP

LD

U21

SP

FL

JPL

CS

1LD

PL

EX

LE

XD

EX

NC

S2L

DA

A1

SC

NL

SJA

LB

PL

1EN

RT

PL

3RE

2RE

1RE

NO

RD

AA

22E

NR

PM

LO

NLL

DU

PK

EX

UP

K

EX

DW

K

EX

MO

DK

ZU

PK

ZD

WK

CR

SK

BP

K

10U

PK

MA

GK

SC

NK

OLK

CLK

1UP

K

PS

W

CV

OP

RP

L

SK

QN

AB

D01

0

SW

16

LTL-

1LH

EE

-002

A

LED

74

TP

52

d1Q

306

2SB

1197

K

2

13

C3411000p

CN

304

18F

MN

-BM

TT

R-A

-TB

123456789101112131415161718

SK

QN

AB

D01

0S

W19

IC30

6

74H

C15

1

D0

4

D1

3

D2

2

D3

1

D4

15

D5

14

D6

13

D7

12

A11

B10

C9

G7

W6

Y5

VC

C16

GN

D8

SK

QN

AB

D01

0S

W23

C3471000p

b2

TP

25

R38

210

0J

TP

5

C3391000p

g2

TP

42

d3

D31

7

1SS

133

LTL-

1LH

G-0

02A

LED

98

C32

8

200P

F

TP

59

C3361000p

C35

4

N.M

.

LTL-

1LH

G-0

02A

LED

79

TP

36

TP

45

LTL-

1LH

G-0

02A

LED

90

TP

53

R36

347

0J

R4014.7KJ

SK

QN

AB

D01

0S

W28

R37

615

0J

LTL-

1LH

G-0

02A

LED

70

D31

3

1SS

133

TP

2

C3321000p

TP

16

TP

26T

P6

R3974.7KJ

R40

915

0J

R37

215

0J

LTL-

1LH

G-0

02A

LED

61

TP

43

C34

3

2200

0PF

R41

651

0J

TP

60

TP

46

C3291000p

TP

54

LTL-

1LH

EE

-002

A

LED

94

R36

815

0J

LTL-

1LH

G-0

02A

LED

75

R42

610

kJ

TP

18

R42

215

0J

C34

6

200P

F

c1

R38

710

0J

IC30

5

74H

C15

1

D0

4

D1

3

D2

2

D3

1

D4

15

D5

14

D6

13

D7

12

A11

B10

C9

G7

W6

Y5

VC

C16

GN

D8

TP

17

TP

27

TP

49

SK

QN

AB

D01

0S

W24

R4064.7KJ

TP

7

a2

C34

9

0.1u

F

TP

28

C34

8

2200

0PF

R42

51k

J

R38

310

0J

C34

5

200P

FT

P61

f3

TP

47

C3401000p

c3

LTL-

1LH

G-0

02A

LED

99

SK

QN

AB

D01

0S

W20

TP

55

LTL-

1LH

G-0

02A

LED

80

R42

71k

J

D31

81S

S13

3

LTL-

1LH

G-0

02A

LED

91

TP

13

TP

19 R38

010

0J

R4314.7KJ

TP

50

R36

447

0J

R40

210

0J

LTL-

1LH

G-0

02A

LED

71

TP

8

g1

TP

29

D31

41S

S13

3

TP

51

C3331000p

TP

62

TP

65

f2

TP

48

R3984.7KJ

IC30

4

LC79

35A

N

IC30

4

/Q333

/Q434

/Q536

/Q637

/Q738

/Q940

/Q1041

/Q1142

/Q17 1

/Q18 2

/Q19 3

/Q20 4

/Q216

/Q227

/Q238

/Q249

/Q2510

/Q2611

/Q1243

/Q1345

/Q1446

/Q1547

/Q839

/Q131

VCC 63

/STROBE 51

BEO 49

/LATCH 50

S IN 30

CLOCK 64

S OUT 19

GND1 5

GND2 14

GND3 35

GND4 44

GND5 62

/Q31 17

/Q30 16

/Q2813

/Q2712

/Q32 18

/Q16 48

/Q232

/Q29 15

TP

56

R37

315

0J

Q30

42S

B11

97K

2

13

R41

71K

J

SK

QN

AB

D01

0S

W29

C35

1

N.M

.

TP

20

C3301000p

LTL-

1LH

G-0

02A

LED

95

LTL-

1LH

G-0

02A

LED

72

R3944.7KJ

b1

TP

9

R3914.7KJ

CN

303

S3B

-PH

-K-S

1 2 3

R36

915

0J

TP

30

R38

810

0J

R41

31K

J

SK

QN

AB

D01

0S

W25

LTL-

1LH

G-0

02A

LED

67

TP

15

TP

63 TP

66

R40

710

0J

C35

0

0.1u

F

R42

11K

J

TP

57

CN

305

NM

_ S

3B-P

H-K

-R

(RE

D)

1 2 3

R41

81K

JR

410

150J

SK

QN

AB

D01

0S

W21

b3

R38

410

0J

R37

815

0J

TP

21

LTL-

1LH

G-0

02A

LED

81

LTL-

1LH

G-0

02A

LED

92

R40

410

0J

TP

10

D31

91S

S13

3

TP

31

C3371000p

R42

31.

5KJ

LTL-

1LH

G-0

02A

LED

76

f1

TP

37

TP

64 TP

67

SK

QN

AB

D01

0S

W17

R4034.7KJ

d2

D31

51S

S13

3

C3341000p

TP

22

R36

515

0J

TP

70

R3994.7KJ

LTL-

1LH

G-0

02A

LED

96

R37

415

0J

TP

11

C35

2

N.M

.

LTL-

1LH

G-0

02A

LED

77

D31

1

1SS

133

TP

32

C3311000p

a1

TP

38

TP

68

SK

QN

AB

D01

0S

W26

R3954.7KJ

SK

QN

AB

D01

0S

W30

R40

815

0J

R37

015

0J

LTL-

1LH

EE

-002

A

LED

68

R3924.7KJ

R41

451

0J

R38

910

0J

TP

71

SK

QN

AB

D01

0S

W22

a3

R41

91K

J

R36

615

0J

TP

12

R38

510

0J

e2

R37

715

0J

R41

11.

5KJ

TP

33

LTL-

1LH

G-0

02A

LED

102

R4054.7KJ

TP

39

TP

69

LTL-

1LH

G-0

02A

LED

73

R42

810

kJ

D32

01S

S13

3

e1

R38

110

0J

SK

QN

AB

D01

0S

W18

R33

91K

J

C3381000p

R42

410

kJ

c2

D31

6

1SS

133

TP

23

g3

C3351000p

LTL-

1LH

G-0

02A

LED

97

e3

LTL-

1LH

G-0

02A

LED

78

R4004.7KJ

TP

40

LTL-

1LH

EE

-002

A

LED

89

R42

91k

J

R37

515

0J

TP

1

D31

21S

S13

3

Q30

52S

B11

97K

2

13

C35

3

N.M

.

TP

34

R37

915

0J

SK

QN

AB

D01

0S

W27

R43

010

0J

NM

_LT

L-1L

HE

E-0

02A

LED

69

R3964.7KJ

R3934.7KJ

C34

4

200P

F

R37

115

0J

R41

51K

J

C34

2

47uF

/16V

TP14

TP

24

R39

010

0J

C355

NM_1000p

LTL-

1LH

G-0

02A

LED

60

LTL-

1LH

G-0

02A

LED

101

TP

41

R36

715

0JR

420

150J

TP

3

TP

58

R38

610

0J

LTL-

1LH

G-0

02A

LED

93

R41

21.

5KJ

TP

35

TP

44

A A

B B

C C

D D

E E

44

33

22

11

OP

ER

ATI

ON

PW

B (7

SE

G) (

AL-

2030

/204

0CS

)1/

1


3. MCU PWB (AL-2050CS)A A

B B

C C

D D

E E

44

33

22

11

CPUCLK

(FW)

/LWR#

/CS0#

/CS2#

CPU_SYNC

/CS1#

SCL

CCD_TG

SDA

ARB_INT

A0

A5

A2

A4

A11

A19

A13

A3

A8

A10

A7

A12

A16

A14

A18

A1

A15

A17

A6

A9

/HWR#

/RD#

(SPPD)

CPU_

SYNC

/RE

S_NIC

(PSW)

CCD_TG

(FW)

ARB_INT

/CS3#

/RE

S_U

SB20PROTECT

DMT3

/WDTOVF

D14

P60

POFF

D8

D5

D1

DMT0

D1

D15

D7

D11

D3

D0

D12

D11

D13

D8

D3

P60

D10

D4

D7

D5

DMT1

D9

DMT2

D6

D2

D9

D14

D6

D4

D10

/STBY

/STBY

/PRINT

ST

D12

D15

D2

D13

/ES_SRDY

ES_CMD

ES_

ST

S

ES_CMD

/ES_

SRDY

/PRINT

ST

ES_ST

S

/RD#

/LWR#

/HWR#

DMT3

DMT0

DMT2

DMT1

NMI

NMI

/WDTOVF

RSV_IN0

EXTAL

XTAL

SPFMT1

SPFMT3

SPFMT2

SPFMT0

/ES_PAGE

D0

RY/BY

RxD

SPFMT0

SPFMT1

SPFMT2

/TRAN

SST

SPFMT3

/SCAN

ST

/ES_PAGE

/SCAN

SP

RY/BY

/CS5#

/CS5#

/SCAN

ST

/SCAN

SP

/TRAN

SST

/RE

S_FAX

/RE

S_NIC

/RE

S_U

SB20

/RE

S_OA982

/RE

S_IOA

SIC

/RE

S_GA

SIC

/RE

S_GA

SIC

/RE

S_IOA

SIC

/RE

S_OA982

/CS3#

/CS1#

/CS0#

/CS2#

A20

CPUCLK

EXTALXTAL

/RE

S_FAX

SCL

RxD

SDA

TXD

POFF

CRUM

SDA

TxD

CPU3.3

CPU3.3

VCC3

VCC3

VCC3

A[20

..0]

(2,3,4)

(PSW)

(8)

CCD_TG

(2,5)

/PRINT

ST

(2)

CPU_SYNC

(2)

ARB_INT

(2)

D[15

..0]

(2,3,4,13)

(SPPD)

(8)

(FW)

(5,9)

DMT2

(7)

DMT1

(7)

DMT0

(7)

DMT3

(7)

(TC

S_AN)

(6)

RTH

(6)

ES_ST

S(9)

ES_CMD

(9)

/HWR

(3,4)

/LWR

(2)

/ES_SRDY

(9)

/CSIOA

SIC

(3)

/CSGA

SIC

(2)

/CS

SRAM

(4)

/CSFROM

(4)

SDA

(4)

MMCLK

(6)

/RD

(2,3,4,5)

POFF

(6)

TxD

(12)

RxD

(12)

SCL

(4)

BZR

(11)

/ES_PAGE

(9)

CRUM

SDA

(16)

CRUM

SCL

(16)

SPFMT3

(5)

SPFMT0

(5)

SPFMT1

(5)

/SCAN

SP

(2)

PMCLK

(6)

SPFMT2/MIRCNT

(5)

/TRAN

SST

(2)

/SCAN

ST

(2)

RY/BY

(4)

/CS5

(13)

CPUCLK#

(3)

/RE

SET1

(5)

VIDEO#

(2,5)

LCDCONT

(6)

RE

SETOUT1

(5)

mt_

at_

hom

e#

(5)

/RE

S_U

SB20

(10)

/RE

S_FAX

(13)

/RE

S_OA982

(9)

/RE

S_GA

SIC

(2)/RE

S_IOA

SIC

(3)

/RE

S_NIC

(15)

(PSFANLK)

(8)

TP9

TP65

TP35

TP86

C200.1U

C250.1U

BR7

NM_10KJX4

1 2 3 4

8 7 6 5

FB1

0J<1608>

R132

10KJ

R26

10KJ

R364

33J

TP52

TP66

TP22

R94

10KJ

R51

33J

TP79

BR2133JX4

1234

8765

TP101

BR9

NM_10KJX4

1 2 3 4

8 7 6 5

TP32

TP81

R4

NM

TP72

R23

2KJ

TP106

BR2233JX4

1234

8765

TP44

R5033J

BR3

10KJX4

1 2 3 4

8 7 6 5

TP95

IC2

H8

S/2321

HD

6412

321V

F25

(H8S

/232

1)

P35/SCK1

64

P34/SCK0

63

P33/R

xD1

62

P32/R

xD0

61

P31/T

xD1

60

P30/T

xD0

59

VCC

58

PD7/D15

57

PD6/D14

56

PD5/D13

55

PD4/D12

54

Vss

53

PD3/D11

52

PD2/D10

51

PD1/D9

50

PD0/D8

49

PE7/D7

48

PE6/D6

47

PE5/D5

46

PE4/D4

45

Vss

44

PE3/D3

43

PE2/D2

42

PE1/D1

41

PE0/D0

40

VCC

39

AV

cc

103

Vref

104

P40/AN0

105

P41/AN1

106

P42/AN2

107

P43/AN3

108

P44/AN4

109

P45/AN5

110

P46/AN6/DA0

111

P47/AN7/DA1

112

AV

ss

113

Vss

114

P17/PO15/TIOCB2/TCLKD

115

P16/PO14/TIOCA2

116

P15/PO13/TIOCB1/TCLKC

117

P14/PO12/TIOCA1

118

P13/PO11/TIOCD0/TCLKB

119

P12/PO10/TIOCC0/TCLKA

120

P11/PO9/TIOCB0/DACK1

121

P10/PO8/TIOCA0/DACK0

122

MD0

123

MD1

124

MD2

125

PG0/CA

S126

PG1/C

S3

127

PG2/C

S2

128

PG3/CS11

PG4/CS02

Vss3

NC4

VCC5

PC0/A06

PC1/A17

PC2/A28

PC3/A39

Vss10

PC4/A411

PC5/A512

PC6/A613

PC7/A714

PB0/A815

PB1/A916

PB2/A1017

PB3/A1118

Vss19

PB4/A1220

PB5/A1321

PB6/A1422

PB7/A1523

PA0/A1624

PA1/A1725

PA2/A1826

PA3/A1927

Vss28

PA4/A20/IRQ429

PA5/A21/IRQ530

PA6/A22/IRQ631

PA7/A23/IRQ732

P67/CS7/IRQ333

P66/CS6/IRQ234

Vss35

Vss36

P65/IRQ137

P64/IRQ038

P53/ADTRG102

P52/SCK2101

Vss100

Vss99

P51/RxD298

P50/TxD297

PF0/BREQ96

PF1/BACK95

PF2/LCAS/WAIT/BREQO94

PF3/LWR93

PF4/HWR92

PF5/RD91

PF6/AS90

VCC89

PF7/088

Vss87

EXTAL86

XTAL85

VCC84

STBY83

NMI82

RES81

WDTOVF80

P20/PO0/TIOCA379

P21/PO1/YICOB378

P22/PO2/TIOCC377

P23/PO3/TIOCD376

P24/PO4/TIOCA475

P25/PO5/TIOCB474

P26/PO6/TIOCA573

P27/PO7/TIOCB572

P63/TEND171

P62/DREQ170

P61/TEND0/CS569

Vss68

Vss67

P60/DREQ0/CS466

Vss65

TP13

TP59

TP40

TP24

TP43

TP2

TP48

TP15

BR2333JX4

1234

8765

TP70

BR5

10KJX4

1 2 3 4

8 7 6 5

TP26

TP10

TP98

TP93

TP84

C2

0.1U

TP734

C70NM

BR2433JX4

1234

8765

TP724

TP17

C4

100P

R52

10KJ

TP67

TP28

TP76

TP51

TP102

TP87

R19

10KJ

C833P

TP80

BR2533JX4

1234

8765

R12

22J

R16

33J

TP6

R66

10KJ

BR10

10KJX4

1234

8765

TP54

TP56

TP19

R2

NM

TP107

TP90

C1222P

R11

10KJ

BR16

33JX4

1 2 3 4

8 7 6 5

C14NM

TP73

BR6

10KJX4

1 2 3 4

8 7 6 5

C13NM

C6

12P

C15NM

BR17

33JX4

1 2 3 4

8 7 6 5

R17

33J

TP96

BR13

10KJX4

1 2 3 4

8 7 6 5

R20

330J

TP61

TP11

R9

10KJ

C933P

R1

NM

TP735

TP64

X1AT-49

19.6608MHz

BR18

33JX4

1 2 3 4

8 7 6 5

R67

10KJ

TP37

TP29

TP5

TP103

TP99

TP85

TP78

TP36

C210.1U

BR19

33JX4

1 2 3 4

8 7 6 5

R18

33J

R384

33J

TP69

TP38

TP20

C220.1U

TP108

R3

0J

TP47

TP88

BR20

33JX4

1234

8765

R13

33J

R6

NM

C230.1U

C733P

TP7

TP55

TP23

BR12

10KJX4

1 2 3 4

8 7 6 5

TP33

TP3

C10NM

TP109

TP68

C240.1U

R5

10KJ

TP12

TP91

TP82

R78

1KJ

TP42

TP75

TP46

TP14

TP1

TP25

R7

0J

TP729

R8

NM

C19

10U/10V<2012>

TP30

C3

100P

C5

15PF

TP63

TP16

TP97

BR1

10KJX4

1 2 3 4

8 7 6 5

TP49

TP27

R22

33J

R392

10KJ

R21

2KJ

TP74

R95

10KJ

TP50

TP8

BR11

10KJX4

1 2 3 4

8 7 6 5

TP100

C369NM

TP53

TP34

TP71

R15

100J

L1NM_ZJSR5101-223TA

TP4

TP21

TP94

TP89

R25

33J

TP57

R24

10KJ

TP31

BR2

10KJX4

1 2 3 4

8 7 6 5

IC1

CY25811

SC

XIN/CLKIN

1

XOUT

8VDD

7

VS

S2

SSCLK

5FR

SEL

6

S0

4

S1

3

R131

10KJ

TP92

TP83

C115PF

TP77

TP105

R14

33J

R53

10KJ

TP62

BR4

10KJX4

1 2 3 4

8 7 6 5

TP41

C11

NM

MC

UP

WB

(CP

Use

ctio

n)

(AL

-205

0CS

)1/

16


MM_BI2

MM_AI0

MM_BI1

MM_AI2

MM_BI0

MM_AI1

/INIT

/SLCTIN

/AUTOFD

/STB

PARAD7

PARAD6

PARAD5

PARAD4

PARAD3

PARAD2

PARAD1

PARAD0

VPIN

RCV

VMIN

/POREQ

/PIREQ

PODATA0

PODATA1

PODATA2

PODATA3

PODATA4

PODATA5

PODATA6

PODATA7

CLK

SW

MEM_INT

/INREQ

/OUTACK

/FAXPRO

/PCLPRO

/OUTC

S

A8

D9

D7

RAM_CLK_OUT

D4

D2

MEM_INT

MM_AI0

D8

PFCLKIN

D15

PFCLKOUT

D3

D0

A7A6

A5

CLKSW

MM_BI1

MM_BI0

MM_AI1

D1

D13

D5

D12D11

PFCLK

A4

A2A1

A9

A3

D6

SFCLK48

D10

PFCLK

SYNC#

D14

AFE_DB7

AFE_DB6

AFE_DB5

AFE_DB4

AFE_DB3

AFE_DB2

AFE_DB1

AFE_DB0

AFE_SDI

JTG_TDI

JTG_TM

S

JTG_TCK

JTG_TDO

MAD11

MAD8

MAD4

MAD1

MAD2

MAD5

MAD6

MAD9

MAD3

MAD0

MAD7

MAD12

MAD10

AFE_SDI

RAMDB15

RAMDB9

RAMDB5

RAMDB0

RAMDB3

RAMDB12

RAMDB12

RAMDB7

RAMDB6

RAMDB1

RAMDB8

RAMDB4

RAMDB2

RAMDB13

RAMDB9

RAMDB6

RAMDB8

RAMDB2

RAMDB1

RAMDB14

RAMDB7

RAMDB10

RAMDB5

RAMDB0

RAMDB11

RAMDB15

RAMDB10

RAMDB4

RAMDB11

RAMDB13

RAMDB14

/ESPRD

PODATA0

RAM_CLK_OUT

SYNC#

/SLCTIN

/INIT

PE

/FAULT

PARAD0

PARAD1

PARAD2

PARAD3

PARAD4

PARAD5

PARAD6

PARAD7

PIDATA5

PIDATA7

PIDATA0

PIDATA1

PIDATA3

PIDATA4

PIDATA6

PIDATA2

MM_BI2

MM_AI2

PODATA1

PODATA2

PODATA3

PODATA4

PODATA5

PODATA6

PODATA7

RCV

VPIN

VMIN

/REV

/ACK

BU

SY

SLCT

/AUTOFD

/STB

RSV_OUT0

RSV_OUT1

RSV_OUT2

PFCLKOUT

PFCLKIN

/PCLPRO/FAXPRO

/OUTACK/OUTCS

/INREQ

JTG_TCKJTG_TMS

JTG_TDIJTG_TDO

AFE_DB0

AFE_DB1

AFE_DB2

AFE_DB3

AFE_DB4

AFE_DB5

AFE_DB6

AFE_DB7

RAMDB3

SFCLK48B

SFCLK48A

SFCLK48

SFCLK48B

S1

SFCLK48A

S0

S1

G3.3V

VCC3

VCC3

VCC3

VCC3

G3

.3V

VCC3

VCC3

VCC3

VCC3

VCC3

VCC3

VCC3

VCC3

VCC3

VCC3

AFE_SEN

(5)

ADCLK

(5)

CCD_CP

(5)

CCD_PHI1

(5)

CCD_PHI2

(5)

CCD_TG

(1,5)

CL

(14)

CCD_R

S(5)

VSAMP

(5)

AFE_

SCK

(5)

BSAMP

(5)

/H_SYNC

(9)

PIDATA[7

..0]

(9)

PODATA[7

..0]

(9)

/POACK

(9)

/PIREQ

(9)

/POREQ

(9)

/PIACK

(9)

/PIWR

(9)

/SCAN

SP

(1)

/SCAN

ST

(1)

/TRAN

SST

(1)

/PRINT

ST

(1)

OP_CLK

(5)

TM

(5)

TM_

(5)

OP_LATCH

(5)

OP_DATA

(5)

MM_Y1

(6)

MM_PH_A

(7)

MM_AI0

(7)

MM_AI1

(7)

MM_PH_B

(7)

MM_BI0

(7)

MM_BI1

(7)

MM_Y2

(6)

MM_Y3

(6) BANK1

(4)

BANK0

(4)

/SDCA

S(4)

/SDRA

S(4)

/SDC

S(4)

DQM0

(4)

MAD[12..0]

(4)

/SDWDE

(4)

SDCKE

(4)

DQM1

(4)

CPF

S2

(6)

PR

(6)

HL

(6)

MPF

S(6)

MIRON

(5)

SPFON

(5)

KEY

SC1

(5)

KEY

SC3

(5)

KEY

SC2

(5)

(/A

SIC_R

ST)

(3,5)

/PR_LINE

(9)

/SC_LINE

(9)

/IMC_READY

(9)

RAMDB[15

..0]

(4)

A[20..0]

(1,3,4)

D[15

..0]

(1,3,4,13)

SDCLK

(4)

(/SYNC)

(5)

/REV_O

(15)

/FAULT_O

(15)

/ACK_O

(15)

BU

SY_O

(15)

PE_O

(15)

SLCT_O

(15)

PARAD[7

..0](15)

/RE

S_GA

SIC

(1)

GA

SIC_READY

(12)

AFE_DB[7

..0]

(14)

AFE_SDI

(5)

/RE

SET0

(4,5,9,12)

MIRCNT

(5)

CPU_SYNC

(1)

ARB_INT

(1)

/CSGA

SIC

(1)

/LWR

(1)

/RD

(1,3,4,5)

VIDEO#

(1,5)/LEND

(6)

MMD

(6)

PMD

(6)

TC

(6)

GRIDL

(6)

MC

(6)

BIA

S(6)VFMCNT_12V

(6)VFM_24V

(6)/FPOFF

(9)

CPF

S1

(6)

MRP

S3

(6)

MRP

S2

(6)

MRP

S1

(6)

LDEN

(6)

RR

S(6)

PTPUL

SE

(6)

/INIT_I

(15)

/STB_I

(15)

/AUTOFD_I

(15)

/SLCTIN_I

(15)

FWREN

(5)

TP875

TP260

C340.1U

TP879

TP835

TP157

TP865

TP845

TP236

R61

10KJ

TP226

TP173

TP160

C280.1U

TP819

C350.1U

TP195

R41

33J

R356

10KJ

C74

NMR59

33J

TP250

C37

10U/10V<2012>

TP821

C29212P

R69

10J

TP124

TP113

C360.1U

TP817

TP204

IC4

HG73C141HFV(LF)

AS

IC

CPU_DATA71

CPU_DATA62

CPU_DATA53

CPU_DATA44

CPU_DATA18

CPU_DATA36

CPU_DATA27

VCC(AC)5

CPU_DATA09

GND(AC)10

MIRCNT11

/CPUSYNC12

MEM_INT13

ARB_INT14

VCC(CORE)15

CPU_AD816

CPU_AD717

CPU_AD618

CPU_AD519

GND(CORE)20

RAM_CLK_IN21

CPU_AD422

CPU_AD323

CPU_AD224

CPU_AD125

CPU_AD026

/CPUCS27

SFCLK4828

GND(CORE)29

/CPUWR30

/CPURD31

/RESET32

PFCLK34

CLKSW35

GND(CORE)36

PFCLKOUT37

PFCLKIN38

GND(PLL)39

VCC(PLL)40

GND(PLL)41

VCC(PLL)42

TM2_15M43

/SYNC44

GND(AC)45

/VIDEO46

/LEND47

VCC(AC)48

OUTP00A49

OUTP02A51

OUTP03A52

OUTP04A53

OUTP05A54

OUTP06A55

VCC(CORE)57

OUTP15A56

OUTP07A58

OUTP08A59

GND(CORE)60

OUTP09A61

OUTP10A62

OUTP11A63

OUTP12A64

VCC(CORE)

86

OUTP13B

84

OUTP12B

83

OUTP10B

81

GND(AC)69

OUTP09B

80

OUTP08B

79

OUTP03B72

GND(CORE)

78

OUTP07B

77

OUTP06B

76

OUTP00B68

OUTP14A67

VCC(CORE)66

OUTP13A65

VCC(AC)74

OUTP04B73

OUTP11B

82

OUTP02B71

OUTP05B

75

OUTP14B

85

OUTP01B70

TSP_MODE

96

OPE_CLK

92

/TM

87

TM

88

OPE_DATA

89

OPE_LATCH

90

GND(AC)

91

VCC(AC)

93

/SCAN

SP

94

TSO0

95

IE1284_

STB

97

IE1284_AUTOFD

98

VCC(CORE)

99

IE1284_

SLCTIN

100

IE1284_INIT

101

IE1284_SLCT

102

GND(CORE)

103

IE1284_PE

104

IE1284_BU

SY

105

IE1284_ACK

106

IE1284_FAULT

107

VCC(CORE)

108

IE1284_REV

109

IE1284_PARAD7

110

IE1284_PARAD6

111

IE1284_PARAD5

112

IE1284_PARAD4

113

IE1284_PARAD3

114

IE1284_PARAD2

115

VCC(AC)

116

IE1284_PARAD1

117

IE1284_PARAD0

118

SU

SPEND

119

GND(AC)

120

OEN

121

VMOUT

122

VPOUT

123

GND(CORE)

124

VMIN

125

VPIN

126

RCV

127

/SCAN

ST

128

VCC(CORE)192

/INREQ191

/OUTCS190

/OUTACK189

/ESPRD188

/FAXPRD187

/PCLPRD186

GND(AC)185

MDAT15184

MDAT14183

MDAT13182

VCC(CORE)181

MDAT12180

MDAT11179

MDAT10178

VCC(AC)177

MDAT09176

MDAT08175

MDAT07174

GND(CORE)173

MDAT06172

MDAT05171

MDAT04170

VCC(CORE)169

MDAT03168

MDAT02167

MDAT01166

MDAT00165

GND(AC)164

/INCS163

/INACK162

/OUTREQ161

GND(CORE)160

/HSYNC159

PIDATA0158

PIDATA1157

PIDATA2156

VCC(AC)155

PIDATA3154

PIDATA4153

PIDATA5152

PIDATA6151

PIDATA7150

/POCS149

/POREQ

148

VCC(AC)

147

/PIWT

146

/PIACK

145

GND(AC)

144

/POACK

143

/PIREQ

142

GND(CORE)

141

PODATA0

140

PODATA1

139

PODATA2

138

PODATA3

137

PODATA4

136

PODATA5

135

PODATA6

134

PODATA7

133

VCC(CORE)

132

/TRAN

SST

131

/RECEPT

ST

130

/PRINT

ST

129

RAM_DATA4

256

RAM_DATA5

255

RAM_DATA6

254

RAM_DATA7

253

GND(AC)

252

RAM_DQM0

251

RAM_WDE

250

VCC(AC)

249

RAM_CA

S248

RAM_RA

S247

RAM_C

S246

RAM_BANK

S0

245

RAM_BANK

S1

244

VCC(CORE)

243

RAM_MAD10

242

RAM_MAD0

241

RAM_MAD1

240

GND(CORE)

239

RAM_MAD2

238

RAM_MAD3

237

GND(AC)

236

MM_AI2

235

MM_AI1

234

MM_AI0

233

MM_PH_A

232

AFE_DB3217

MM_BI2

231

MM_BI1

230

MM_Y2

225

VCC(AC)221

MM_Y1

226

AFE_DB0220

AFE_DB1219

GND(CORE)

223

AFE_DB2218

AFE_DB4216

AFE_DB5215

MM_BI0

229

MM_PH_B

228

VCC(CORE)

227

MM_Y3

224

CLPWM222

AFE_DB6214

AFE_DB7213

GND(AC)212

AFESCK211

VCC(CORE)210

ADCLK209

GND(CORE)208

AFE_SEN207

CCD_PH1206

CCD_PH2205

AFE_SDI204

CCD_CP203

BSAMP202

CCD_RS201

CCD_TG200

VSAMP199

GND(CORE)198

TD0197

TRSK195

TDI196

TCK193

TMS194

VCC(CORE)33

OUTP01A50

GND(CORE)

257

RAM_DATA3

258

RAM_DATA2

259

RAM_DATA1

260

RAM_DATA0

261

GND(AC)

262

RAM_DATA15

263

RAM_DATA14

264

VCC(CORE)

265

RAM_DATA13

266

RAM_DATA12

267

RAM_DATA11

268

RAM_DATA10

269

RAM_DATA9

270

RAM_DATA8

271

VCC(CORE)

272

RAM_DQM1

273

RAM_CKE

274

GND(AC)

275

RAM_CLK_OUT

276

GND(CORE)

277

RAM_MAD12

278

RAM_MAD11

279

RAM_MAD9

280

VCC(CORE)

281

RAM_MAD8

282

RAM_MAD7

283

VCC(AC)

284

RAM_MAD6

285

RAM_MAD5

286

RAM_MAD4

287

GND(AC)

288

CPUDATA15

289

CPUDATA14

290

CPUDATA13

291

CPUDATA12

292

CPUDATA11

293

CPUDATA10

294

CPUDATA9

295

CPUDATA8

296

TP221

TP162

TP228

TP151

BR51

82JX4

1 2 3 4

8 7 6 5

TP245

TP213

TP190

R359

10KJ

C390.1U

TP205

TP181

TP382

TP846

BR27

10KJX4

1234

8765

R70

0J

TP486

TP861

TP185

TP135

TP119

C66

NM

TP507

TP740

TP212

TP141

C420.1U

TP325

TP150

TP823

TP235

TP261

TP130

C29312P

R31

33J

BR38

33JX4

1 2 3 4

8 7 6 5

BR41

10KJX4

1 2 3 4

8 7 6 5

C400.1U

TP869

TP237

TP197

TP175

TP174

TP163

C399

10U/10V<2012>

C411

0.1U

BR30

33JX4

1 2 3 4

8 7 6 5

BR26

10KJX4

1234

8765

BR55

10KJX4

1 2 3 4

8 7 6 5

C410.1U

R73

NM

TP256

TP727

TP125

TP114

TP876

TP227

TP220

TP198

BR4733JX4

1 2 3 4

8 7 6 5

IC9

CY25814SC

XIN/CLKIN

1

XOUT

8VDD

7

VS

S2

SSCLK

5FR

SEL

6

S0

4

S1

3

TP847

BR32

33JX4

1 2 3 4

8 7 6 5

TP836

BR52

10KJX4

1 2 3 4

8 7 6 5

C380.1U

TP872

TP866

TP142

TP828

TP152

TP402

TP246

C29412P

C76

0.1U

BR2833JX4

1 2 3 4

8 7 6 5

TP490

TP187

BR53

10KJX4

1 2 3 4

8 7 6 5

C430.1U

R30

33J

TP627

TP862

TP207

TP238

TP136

TP120

BR4333JX4

1 2 3 4

8 7 6 5

R47

10KJ

TP215

TP741

TP159

C440.1U

C58

47P

C351

NM

TP825

TP736

TP199

R46

10KJ

TP719

TP153

R68

0J

TP252

TP168

TP144

TP165

TP240

TP229

TP131

BR60

10KJX4

1 2 3 4

8 7 6 5

C450.1U

R32

33J

TP214

TP192

R42

10KJ

R75

NM

TP177

TP206

TP184

BR31

10KJX4

1 2 3 4

8 7 6 5

BR3533JX4

1 2 3 4

8 7 6 5

BR36

33JX4

1 2 3 4

8 7 6 5

C7522000P

TP848

TP176

TP126

TP115

R54

33J

C460.1U

C60

47P

TP223

TP143

R134

NM

TP257

TP230

BR33

10KJX4

1 2 3 4

8 7 6 5

C400

10U/10V<2012>

TP403

BR49

10KJX4

1 2 3 4

8 7 6 5

BR57

10KJX4

1 2 3 4

8 7 6 5

R60

NM

C470.1U

R34

33J

R6533J

TP493

TP837

TP189

TP628

TP881

TP247

TP154

R63NM_33J

TP854

R62

10KJ

X2

NM_

SG8002DC(48MHz)

N.C

.1

VCC

8OUTPUT

5

GND

4

X7

AT-49(12MHz)

TP885

TP164

C480.1U

C62

47P

BR58

10KJX4

1 2 3 4

8 7 6 5

TP892

TP873

TP208

TP137

TP121

C107

10P

BR45

10KJX4

1 2 3 4

8 7 6 5

TP877

TP239

TP110

TP863

TP820

TP167

C77

NM_12P

TP855

TP818

TP742

TP242

TP222

TP200

X5AT-49(18

.3856MHz)

R33

33J

BR54

33JX4

1 2 3 4

8 7 6 5

BR59

10KJX4

1 2 3 4

8 7 6 5

C550.1U

TP746

TP737

C68

NM

R40

10KJ

TP258

TP867

TP132

TP140

C63

NM

C520.1U

C61

47P

BR56

33JX4

1 2 3 4

8 7 6 5

TP217

TP145

R55

33J

TP822

TP720

TP179

TP170

TP127

TP116

R133

33J

BR2933JX4

1 2 3 4

8 7 6 5

TP856

TP255

TP186

C29512P

C401

10U/10V<2012>

R3140J

TP827

C570.1U

R36

33J

TP462

TP232

TP178

TP495

TP201

TP156

R79

0J

TP630

C402

12P

TP146

C560.1U

C64

47P

TP248

TP191

TP155

TP231

C59

47P

TP216

TP193

TP209

TP882

TP857

TP138

TP122

C530.1U

R37

33J

TP161

TP111

BR37

33JX4

1 2 3 4

8 7 6 5

L2ZJSR5101-223TA

TP874

TP241

TP878

TP841

TP243

TP169

C29612P

R56

10KJ

C490.1U

C65

47P

TP253

TP824

TP738

TP147

C270.1U

TP864

TP834

TP133

TP842

TP743

TP224

BR39

33JX4

1 2 3 4

8 7 6 5

BR34

10KJX4

1 2 3 4

8 7 6 5

TP128

TP117

C510.1U

R39

33J

TP351

TP747

TP172

C310.1U

TP468

TP259

TP182

R35

33J

TP498

TP858

BR42

33JX4

1 2 3 4

8 7 6 5

TP859

TP234

TP188

C500.1U

C67

47P

TP843

TP210

TP225

TP202

TP180

TP158

C290.1U

TP891

TP219

C29712P

BR44

33JX4

1 2 3 4

8 7 6 5

TP249

C108

12P

C540.1U

R57

NM

C97

1000P

TP868

C300.1U

R92

NM

TP194

R44

33J

TP139

TP123

TP112

BR48

33JX4

1 2 3 4

8 7 6 5

TP211

C690.1U

TP844

TP149

BR4633JX4

1 2 3 4

8 7 6 5

FB2

NM_0J<1608>

R357

10KJ

C320.1U

TP254

TP244

R48

10J

R38

33J

TP203

TP166

TP171

C29112P

R58

NM

C80 47P

C375

12P

TP739

TP148

TP134

C330.1U

TP251

TP364

TP270

TP233

TP129

TP118

R358

10KJ

R49

10J

TP471

TP860

TP829

TP183

TP218

TP196

C29812P

FB3

0J<1608>

TP500

TP826

BR4033JX4

1 2 3 4

8 7 6 5

R45

10KJ

A A

B B

C C

D D

E E

44

33

22

11

MC

UP

WB

(AS

ICse

ctio

n)

(AL

-205

0CS

)2/

16


RSV_OUT16

D8

D14

RSV_OUT17

D13

RSV_IN2

D9D10

RSV_IN1

D12

D15

D11

A3

A0

A4

A1A2

LCDE

LCDR

S

/ES_CRDY

RSV_OUT12

RSV_OUT13

RSV_OUT10

RSV_OUT8

RSV_OUT11

RSV_OUT14

RSV_OUT15

RSV_OUT9

MSU_

ST1

IOIC3.3V

IOIC3.3V

VCC3

VCC3

VCC3

SELIN3

(11)

SELIN2

(11)

A[20

..0]

(1,2,4)

PSL

(11)

(CED2)

(8)

SFTMT1

(7)

D[15

..0]

(1,2,4,13)

SFTMT3

(7)

KEYIN

(11)

INFOLED

(11)

/RD

(1,2,4,5)

(DR

ST)

(8)

SFTMT0

(7)

SELIN1

(11)

CPUCLK#

(1)

/CSIOA

SIC

(1)

(RSV_SOL)(7)

/HWR

(1,4)

DSW

S(8)

(TC

S)

(8)

DV

S1

(8)

(PD1)

(8)

(CED1)

(8)

(PD2)

(8)

(SCOD)

(8)

LCDDB5

(5)

LCDDB4

(5)

LCDE

(5)

LCDDB6

(5)

LCDR

S(5)

LCDDB7

(5)

/ES_CRDY

(9)

MCNT

(6)

(SRJD)

(8)

(SPID)

(8)

SFTMT2

(7)

(PPD1)

(8)

PSFM

(6)

(PPD2)

(8)

(PPD3)

(8)

(POD)

(8)

(MFD)

(8)

(PMRDY)

(8)

(MMLD)

(8)

(FANLK)

(8)

THOPEN

(6)

(/A

SIC_R

ST)

(2,5) /RE

S_IOA

SIC

(1)

SPU

S(7)

SRVC

(7)

BL

(11)

MSU_ST1

(13)

IOA

SIC

TP299

L15

NM_ZJSR5101-223TA

TP279

C304

10U/10V<2012>

TP313

TP266

TP815

TP294IC52

SC65892(IOA

SIC)<LQFP100>

VDD

1

PHICLK

2

gn

d3

XCE0(PU50K)

4

CE1(PU50K)

5

XOE(PU50K)

6

XWR(PU50K)

7

A4(PU50K)

8

A3(PU50K)

9

A2(PU50K)

10

A1(PU50K)

11

A0(PU50K)

12

XR

ST(S

ch)

13

vdd

14

D7(PU50K)

15

D6(PU50K)

16

SMC(SCAN)(PD50K)

17

SIN(SCAN)(PD50K)

18

SOUT(SCAN)

19

AMC(SCAN)(PD50K)

20

SCK(SCAN)

21

D5(PU50K)

22

D4(PU50K)

23

D3(PU50K)

24

VDD

25

GND26

D2(PU50K)27

D1(PU50K)28

D0(PU50K)29

PORTA7(PD50K)(5VFS)30








vdd38

PORTB7(PD50K)(5VFS)39








PORTC7(PD50K)47

PORTC6(PD50K)48

PORTC5(PD50K)49

GND50

VDD

51

PORTC4(PD50K)

52

PORTC3(PD50K)

53

PORTC2(PD50K)

54

PORTC1(PD50K)

55

PORTC0(PD50K)

56

gnd

57

PORTD7(PD50K)

58

PORTD6(PD50K)

59

PORTD5(PD50K)

60

PORTD4(PD50K)

61

PORTD3(PD50K)

62

PORTD2(PD50K)

63

PORTD1(PD50K)

64

PORTD0(PD50K)

65

gnd

66

PORTE7(PD50K)

67

PORTE6(PD50K)

68

PORTE5(PD50K)

69

PORTE4(PD50K)

70

PORTE3(PD50K)

71

PORTE2(PD50K)

72

PORTE1(PD50K)

73

PORTE0(PD50K)

74

VDD

75

GND76

PORTF7(PD50K)77

PORTF6(PD50K)78

PORTF5(PD50K)79

PORTF4(PD50K)80

PORTF3(PD50K)81

PORTF2(PD50K)82

PORTF1(PD50K)83

PORTF0(PD50K)84

vdd85

PORTG7(PD50K)86

PORTG6(PD50K)87

PORTG5(PD50K)88

PORTG4(PD50K)89

PORTG3(PD50K)90

PORTG2(PD50K)91

PORTG1(PD50K)92

PORTG0(PD50K)93

XCE_EXT94

gnd95

SELA(OD,5VFS)96

SELB(OD,5VFS)97

SELC(OD,5VFS)98

YIN(PD50K)(5VFS)99

GND100

C6630.1U

TP311

TP265

TP303

TP320TP277

TP315

TP321

TP280

TP283

TP300

TP635

TP271

TP317

TP322

TP324

TP318

R122NM_10KJ

R707

4.7KJ

TP319

TP288

R706

NM_10KJ

12

TP316

TP304

TP290

R135

33J

TP272

FB13

0J<1608>

TP305

TP832

TP287

TP281

TP263

R263NM_10KJ

TP262

C5680.1U

C5750.1U

TP636

TP298

C7000.1U

R136

NM

TP286

TP289

C6620.1U

C6600.1U

TP273

TP269

TP296

TP282

TP274

TP284

TP278

TP302

TP267

TP308

C5740.1U

TP307

TP295

TP275

TP312

C98

1000P

TP309

TP285

R10

4.7KJ

TP293

C5690.1U

TP301

TP297

TP314

TP310

TP268

TP292

TP323

TP264

TP276

TP291

TP306

TP811

A A

B B

C C

D D

E E

44

33

22

11

MC

UP

WB

(I/O

AS

ICse

ctio

n)

(AL

-205

0CS

)3/

16


RAMDB0

RAMDB9

RAMDB10

RAMDB11

RAMDB12

RAMDB13

RAMDB14

RAMDB15

RAMDB7

RAMDB8

RAMDB3

RAMDB1

RAMDB5

RAMDB6

RAMDB2

RAMDB4

A12

A7

A10

A11

A17

A9

A12

A5

A16

A14

A1

D14

A15

A8

A6

D10

A2

A4

A10

A14

A13

A15

A3

A6

A16

A7

A11

A2

A4

A8

D9

A13

A9

A18

A19

A5

A1

A0

A3

MAD5

MAD2

MAD7

MAD9

MAD8

MAD3

MAD10

MAD11

MAD1

MAD0

MAD6

MAD4

MAD12

A20

D8

D11

D12

D13

D15

A17

D15

D7

D12

D14

D6D13

D5

D4

D11

D3D10

D2D9D1D8D0

A1

VCC3

VCC3

VCC3

VCC3

VCC3

VCC3

VCC3

VCC3

VCC3

VCC3

VCC3

/CSFROM

(1)

MAD[12..0](2)

BANK0

(2)

BANK1

(2)

/SDC

S(2)

/SDWDE

(2)

/SDCA

S(2)

/SDRA

S(2)

DQM0

(2)

DQM1

(2)

SDCLK

(2)

SDCKE

(2)

D[15..0]

(1,2,3,13)

RAMDB[15..0](2)

/CS

SRAM

(1)

/RD

(1,2,3,5)

/HWR

(1,3)

A[20..0]

(1,2,3)

RY/BY

(1)

/RE

SET0

(2,5,9,12)

VPP

(9)

VPP

(9)

SCL

(1)

SDA

(1)

/HWR

(1,3)

/RD

(1,2,3,5)

Fla

sh

RO

MV

PP

Co

ntr

oll

Se

ria

lE

E-P

RO

M

TP334

TP337

TP346

TP326

TP852

TP813

TP343

R80NMC90

0.1U

R8310KJ

TP350

C91

0.1U

TP358

TP336

C92

0.1U

TP341

TP840

IC5

CAT24WC08LI

E0

1

E1

2

E2

3

VS

S4

SDA

5SCL

6WC

7VCC

8

C93

0.1U

TP359

C94

0.1U

TP353

TP365

TP338

C85

0.1U

R82NM

C95

0.1U

R86

NM

TP347

R81NM

C8722000P

TP352

TP367

TP816

TP851

TP812

TP889

TP340

C355NM

TP839

TP331

TP360

TP335

TP327

TP328

C89

0.1U

TP342

TP369

R77

NM

TP363

C353NM

TP357

TP339

TP354

TP850

C83

NM

IC7

S29AL016D70TFI020

A0

25

A1

24

A2

23

A3

22

A4

21

A5

20

A6

19

A7

18

A8

8A9

7A10

6A11

5A12

4A13

3A14

2A15

1A16

48

A17

17

DQ0

29

DQ1

31

DQ2

33

DQ3

35

DQ4

38

DQ5

40

DQ6

42

DQ7

44

DQ8

30

DQ9

32

DQ10

34

DQ11

36

DQ12

39

DQ13

41

DQ14

43

DQ15

45

A19

9

NC

10

A18

16

GND

46

GND

27

VCC

37

VPP

13

BYTE

47

OE

28

CE

26

WE

11

RP

12

WP

14

RY/BY

15

C352NM

C86NM

C354NM

R74

10KJ

TP838

TP345

IC6

SDRAM(16bit

x4b

ank)

A0

23

A1

24

A2

25

A3

26

A4

29

A5

30

A6

31

A7

32

A8

33

A9

34

A10

22

BA0

20

DQ0

2

DQ1

4

DQ2

5

DQ3

7

DQ4

8

DQ5

10

DQ6

11

DQ7

13

DQ8

42

DQ9

44

DQ10

45

DQ11

47

DQ12

48

DQ13

50

DQ14

51

DQ15

53

VCC

1

VCC

27

VS

S54

VS

S28

VCCQ

9

VS

S41

VCCQ

43

VCCQ

49

VS

SQ

6

VS

SQ

12

VS

SQ

46

VS

SQ

52

LDQM

15

UDQM

39

WE

16

CA

S17

RA

S18

CS

19

CLKE

37

CLK

38

NC

40

NC

36

VCCQ

3

VCC

14

BA1

21

A11

35

R84

10KJ

TP368

TP726

R85

0J

TP329

TP853

TP344

TP362

IC8

IS63LV1024L-12J-TR

I/O0

6A0

1

I/O1

7A1

2

I/O2

10

A2

3

I/O3

11

A3

4

I/O4

22

A4

13

I/O5

23

A5

14

I/O6

26

A6

15

I/O7

27

A7

16

A8

17

A9

18

A10

19

A11

20

A12

21

A13

29

A14

30

CS1

5

OE

28

WE

12

VDD

8

GND

9

VDD

24

A15

31

A16

32

GND

25

R76

100J

C84

0.1U

C82

0.1U

TP349

TP356

TP849

TP361

TP348

TP888

J1,J2

1 2 3

C88

0.1U

TP355

TP333

TP332

TP330

R88NM

TP366

A A

B B

C C

D D

E E

44

33

22

11

MC

UP

WB

(Mem

ory

sect

ion

)(A

L-2

050C

S)

4/16


/RE

SET#

/RE

SET#

AFE_

SDI#

AFE_

SEN#

CCD_TG#

VSAMP#

CCD_R

S#

CCD_PHI1#

CCD_CP#

ADCLK#

CCD_PHI2#

VSAMP#

CCD_TG#

CCD_R

S#

BSAMP#

CCD_CP#

CCD_PHI2#

CCD_PHI1#

ADCLK#

BSAMP#AFE_

SCK#

(/RD)

(PB_NOE)

(PB_NWE)

(PB_NAE0)

AFE_

SCK#

(/RD)

(PB_NOE)

(PB_NWE)

(PB_NAE0)

AFE_

SDI#

AFE_SEN#

VCC3

5V

VCC3

5V

VCC3

VCC3

VCC3

VCC3

VCC3

VCC3

VCC3

VCC3

5V

VCC3

(OP_DATA)

(11)

(OP_LATCH)

(11)

(SPFMT0)

(7)

OP_CLK

(2)

OP_DATA

(2)

SPFMT0

(1)

SPFMT1

(1)

SPFMT3

(1)

MIRON

(2)

SPFON

(2)

(SPFMT1)

(7)

(SPFMT2)

(7)

(SPFMT3)

(7)

TM

(2)

TM_

(2)

(TM)

(7)

(TM_)

(7)

SPFMT2/MIRCNT

(1)

MIRCNT

(2)

KEY

SC1

(2)

KEY

SC2

(2)

KEY

SC3

(2)

OP_LATCH

(2)

(OP_CLK)

(11)

/SYNC

(11)

(/SYNC)

(2)

/ASIC_R

ST

(16)

(/A

SIC_R

ST)

(2,3)

FW

(11)

(FW)

(1,9)

VIDEO#

(1,2)

/VIDEO

(11)

/RE

SET0

(2,4,9,12)

/RE

SET1

(1)

/OP_R

ST

(9,10)

/NIC_R

ST

(15)

/ASIC_R

ST

(16)

RE

SETOUT1

(1)

/FAX_R

ST

(13)

(/A

SIC_R

ST)

(2,3)

/OP_R

ST

(9,10)

mt_

at_

hom

e(14)

mt_

at_

hom

e#

(1)

AFE_

SDI

(2)

AFE_

SEN

(2)

AFE_

SCK

(2)

AFE_

SDI#

(14)

AFE_

SEN#

(14)

AFE_

SCK#

(14)

VSAMP

(2)

CCD_TG

(1,2)

VSAMP#

(14)

CCD_TG#

(14)

CCD_R

S(2)

BSAMP

(2)

CCD_R

S#

(14)

BSAMP#

(14)

CCD_CP

(2)

CCD_PHI1

(2)

CCD_CP#

(14)

CCD_PHI1#

(14)

CCD_PHI2

(2)

ADCLK

(2)

CCD_PHI2#

(14)

ADCLK#

(14)

/RD

(1,2,3,4)PB_NAE0

(9,10)

PB_NWE

(9,10)

PB_NOE

(9,10)

(PB_NOE)

(13)

(PB_NAE0)

(13)

(PB_NWE)

(13)

(/RD)

(13)

/RE

SET0

(2,4,9,12)

LCDDB4

(3)

LCDDB5

(3)

LCDDB6

(3)

LCDDB7

(3)

LCDE

(3)

LCDR

S(3)

LCDDB5#

(11)

LCDDB6#

(11)

LCDDB7#

(11)

LCDE#

(11)

LCDR

S#

(11)

LCDDB4#

(11)

(KEY

SC2)

(11)

(KEY

SC1)

(11)

(KEY

SC3)

(11)

FWREN

(2)

3.3

V

3.3

V3.3

V

5V

3.3

V

3.3

V

3.3

V3.3

V

5V

3.3

V

Re

se

tC

irc

uit

AS

ICR

es

et

OP

Re

se

t

3.3

V

C128

0.1U

TP381

TP718

R119

1KJ

C123

NM

TP386

TP397

TP415TP384

C99

47P

TP407

TP370 C1150.1U

TP895

C306

NM

R223

NM_0J

IC20

74VHCT244

1A1

2

1A2

4

1A3

6

1A4

8

2A1

11

2A2

13

2A3

15

2A4

17

1G

1

2G

19

1Y1

18

1Y2

16

1Y3

14

1Y4

12

2Y1

9

2Y2

7

2Y3

5

2Y4

3

VCC

20

GND

10

R344

33J

IC16

74LCX244

1A1

2

1A2

4

1A3

6

1A4

8

2A1

11

2A2

13

2A3

15

2A4

17

1G

1

2G

19

1Y1

18

1Y2

16

1Y3

14

1Y4

12

2Y1

9

2Y2

7

2Y3

5

2Y4

3

VCC

20

GND

10

R29

10KJ

R333

33J

C3100.01U

R338

33J

C124

NM

R373

33J

TP896

TP377

C290

1U<2012>

TP390

IC23

74LCX244

1A1

2

1A2

4

1A3

6

1A4

8

2A1

11

2A2

13

2A3

15

2A4

17

1G

1

2G

19

1Y1

18

1Y2

16

1Y3

14

1Y4

12

2Y1

9

2Y2

7

2Y3

5

2Y4

3

VCC

20

GND

10

TP412TP375

C307

NM

R101

100J

R354

33J

R110

NM_100J

TP786

R28

33J

C376

NM

TP897

R224

0J

TP395

C125

NM

R374

33J

C105

0.1U

R120

33J

R121

100J

R109

100J

TP417TP387

C308

NM

TP409

TP372 R355

33J

TP898

TP404

R100

33J

C255

0.1U

C120

NM

C126

NM

R375

33J

C104

NM

C17

0.01U

C311NM

TP899

TP396

C309

NM

TP414TP380 R360

33J

TP406

TP378

IC46

NM_TC7SH32FU

1 24

5 3

C127

0.1U

TP394

C26

47P

R376

33J

TP900

R64

33J

TP833

IC26

74LCX244

1A1

2

1A2

4

1A3

6

1A4

8

2A1

11

2A2

13

2A3

15

2A4

17

1G

1

2G

19

1Y1

18

1Y2

16

1Y3

14

1Y4

12

2Y1

9

2Y2

7

2Y3

5

2Y4

3

VCC

20

GND

10

TP419TP389

TP411

TP374

C121

NM

C129

NM

R332

33J

R336

33J

R27

100KJ

R91

33J

TP376

TP398

R361

33J

IC11

NC7WZ17

A1

1

A2

3

Y1

6

Y2

4

GND

2

Vcc

5

TP416TP385

IC3 BU4212F

GND

1

VDD

2

CT

3

VOUT

4

R96

33J

C103

0.1U

TP408

TP371

TP393

C122

NM

C130

NM

C116

NM

C11733P

R89

NM

BR61

33JX4

1234

8765

R71

10KJ

TP383

C110

0.1U

C96

0.1U

R226

NM_10KJ

IC14

NC7WZ17

A1

1

A2

3

Y1

6

Y2

4

GND

2

Vcc

5

TP814

R370

33J

TP391

C79

47P

TP413TP379

R97

33J

C131

NM

C1140.1U

R93

10KJ

IC19

TC74VHC244FT

1A1

2

1A2

4

1A3

6

1A4

8

2A1

11

2A2

13

2A3

15

2A4

17

1G

1

2G

19

1Y1

18

1Y2

16

1Y3

14

1Y4

12

2Y1

9

2Y2

7

2Y3

5

2Y4

3

VCC

20

GND

10

C18

NM

C16

0.1U

TP893

R371

33J

R72

10KJ

IC13

74LCX244

1A1

2

1A2

4

1A3

6

1A4

8

2A1

11

2A2

13

2A3

15

2A4

17

1G

1

2G

19

1Y1

18

1Y2

16

1Y3

14

1Y4

12

2Y1

9

2Y2

7

2Y3

5

2Y4

3

VCC

20

GND

10

TP418TP388

TP410

TP373

R237

10KJ

R98

33J

R345

1KJ

TP405

TP894

A A

B B

C C

D D

E E

44

33

22

11

MC

UP

WB

(Dri

ver

sect

ion

1)(A

L-2

050C

S)

5/16


PR#

/PR

PR#

PGND

24V

PGND

24V

PGND

5V

VCC3

12V

PGND

VCC3

24V

PGND

24V

INT5V

24V

5V

VCC3

VCC3

5V

VCC3

12V

VCC3

VCC3

VCC3

VCC3

12V

VCC3

12V

12V

12V

5V

VCC3

INT24V

PGND

12V

EN5V

VCC3

VCC3

EN5V

12V

12V

12V

VCC3

EN5V

MC

(2)

BIA

S(2)

TC

(2)

GRIDL

(2)

/MC

(11)

/BIA

S(11)

/TC

(11)

/GRIDL

(11)

MCNT

(3)

/MCNT

(12)

PSFM

(3)

/POFF

(11)

POFF

(1)

MRP

S3

(2)

MRP

S_3

(7)

SHOLD

(11)

/LEND

CPF

S2

(2)

/CPF

S2

(12)

MPF

S(2)

CPF

S1

(2)

RR

S(2)

VFM_24V

(2)VFMCNT_12V

(2)

MRP

S2

(2)

MRP

S1

(2)

HL

(2)

LDEN

PMCLK

PMD

MM_Y2

MM_Y1

FTH

MMD

(2)

MM_Y3

/CPF

S1

(12)

VFMOUT

(12)

HLOUT

(11)

/MPF

S(12)

/VFMCNT

(12)

/RR

S(12)

/PMD

(11)

MRP

S_2

(7)

PMCLK_A

(11)

MM

ref1

(7)

/MMD

(12)

/LDEN

(11)

MRP

S_1

(7)

MM

ref0

(7)

/MMCLK

(12)

MMCLK

(1)

MM

ref2

(7)

PSFMOUT

(12)

PTPUL

SE

(2)

TC

S_AN

(16)

(TC

S_AN)

(1)

FTH

RTH

(1)

THOPEN

(3)

RTH_IN

(12)

/PR

(11)

PR

LCDCONT

(1)

(LCDCONT)

(11)

An

alo

gT

on

ner

Sen

so

rB

uff

er

LC

DC

on

tras

tB

uff

er

TP795

TP451

TP430

TP438R102

1KF

TP458

TP428

R113

300J

R383NM

TP427

D58

RL

S-73

D36

1S

S355

R300

470KJ

C371

NM

TP804

R303

10KJ

TP807

R264

12KF

CP17

0603

SFF150FM/32-2

TP801

TP792

R118

1.2KF

IC25

KID65001AF

1B

1

2B

2

3B

3

4B

4

5B

5

6B

6

7B

7

E8

COM

9

1C

16

2C

15

3C

14

4C

13

5C

12

6C

11

7C

10

R26610KJ

R117

10KJ

TP722

TP463

TP445

R114

100J

R308NM

TP459

D56

CRH01

TP448

R316

NM

D66

NM_KD

S226

213

R301

4.7KJ

TP437

R129

NM

TP474

R387

4.7KJ1/4W<3216>

TP449

Q16

KRC102

S

1

2

3

R123

10KF

Q15

NM_2SB1197K

B

E C

TP452

IC27

KID65503F

1B

1

2B

2

3B

3

4B

4

5B

5

6B

6

7B

7

G8

NC

9

1C

16

2C

15

3C

14

4C

13

5C

12

6C

11

7C

10

R307

7.5KF

TP797

TP784

TP435

R413

NM_10KJ

TP444

C111

0.1U/50V<1608>

TP423

R381

NM

TP436

D52

MTZJ22B

TP446

Q20

KRA119

S

1

2

3

Q18

KRC102S

1

2

3

R304

100J

TP472

TP470

Q3

KRA119

S

1

2

3

R302

10KJ

C113

0.1U

R368

NM

TP424

BR62

1.5KJX4

1 2 3 4

8 7 6 5

R124

4.7KJ

C407

NM

D67

KD

S226

213

Q17

KRC102

S

1

2

3

R414

NM_10KJ

TP455

R388

47KJ

R395

1.5KJ

+ -

IC45A

KIA358F-EL/P

3 21

8 4

TP802

TP723

TP439

IC21

KID65001AF

1B

1

2B

2

3B

3

4B

4

5B

5

6B

6

7B

7

E8

COM

9

1C

16

2C

15

3C

14

4C

13

5C

12

6C

11

7C

10

R382

10KJ

TP805

TP454

D5

1S

S355

C112

22000P

TP420

R106

10KF

D4

1S

S355

R380

NM_1.5KJ

D59

NM_KD

S226

213

R142

NM_10KJ

TP798

D2

NM_KD

S226

213

C379

0.1U

C119

22000P

D55

CRH01

R26810KJ

R418

NM_10KJ

R104

7.5KF

TP475

R115

100J1/4W<3216>

+ -

IC22A

KIA393F

3 21

8 4

C118

0.1U/50V<1608>

Q7

KTA1505

S

TP425

TP450

Q4

KRC102

S

1

2

3

TP434

TP426

R297

47KJ

Q21

KRC102S

1

2

3+ -

IC45B

KIA358F-EL/P

5 67

8 4

+ -

IC17A

KIA393F

3 21

8 4

TP461

CP16

0603

SFF150FM/32-2

TP473

TP440

R389

47KJ

+ -

IC53A

KIA358F-EL/P

3 21

8 4

TP793

TP443

R107

4.3KF

R366

0J

TP460

TP429

TP457

R362

4.7KJ1/4W<3216>

R90

10KJ

R396

1.5KJ

TP799

BR63

1.5KJX4

1 2 3 4

8 7 6 5

+ -

IC22B

KIA393F

5 67

8 4

R339

100J

TP781

Q2

NM_KTA1505

S

TP421

D57

RL

S-73

(G)

(D)

(S)

Q19

2SK3018

C398

0.1U

+ -

IC53B

KIA358F-EL/P

5 67

8 4

TP465

R298

1.5KF

TP803

Q13

2SB1132

B

E C

R394

NM

TP553

TP806

TP433

TP464

R363

47KJ

D60

NM_KD

S226

213

D45

1S

S355

TP789

R26910KJ

TP467

R26510KJ

R105

1KJ

+ -

IC17B

KIA393F

5 67

8 4

R386

4.7KJ1/4W<3216>

TP431

TP453

D1

MA700

TP469

TP441

IC24

KID65503F

1B

1

2B

2

3B

3

4B

4

5B

5

6B

6

7B

7

G8

NC

9

1C

16

2C

15

3C

14

4C

13

5C

12

6C

11

7C

10

R296

10KJ

C305

0.1U

TP447

TP794

R379

NM_1.5KJ

R112

NM_4.7KJ1/4W<3216>

R419

NM_10KJ

TP800

TP456

R27010KJ

R299

100J

Q12

2SB1132

B

E C

D3

KD

S226

213

C312

1U<2012>

R103

1MF

C367

2.2U<2012>

D61

1S

S355

R116

10KJ

Q14

KRC102

S

1

2

3

D51

1S

S355

R378

0J

TP476

R108

NM_47KJ

R3930J

TP466

TP790

TP785

TP432

TP442

TP422

R27110KJ

A A

B B

C C

D D

E E

44

33

22

11

MC

UP

WB

(Dri

ver

sect

ion

2)(A

L-2

050C

S)

6/16


PGND

PGND

PGND

5V

24V

SCMT5V

5V

5V

PGND

PGND

PGND

PGND

PGND

PGND

PGND

PGND

PGND

24V

SFTMT

24VDu

pMT

PGND

24V

SPFMT

PGND

5V

PGND

24V

24V

SPF

SOL

24V

SCMT

24VDu

pMT

PGND

24V

SPFMT

24V

PGND

24V

SFTMT

24V

SPF

SOL

MM_PH_A

(2)

OUT_A-

(12)

MM_AI0

(2)

MM_PH_B

(2)

MM_BI0

(2)

MM_BI1

(2)

MM_AI1

(2)

OUT_A+

(12)

OUT_B-

(12)

MM

ref0

(6)

MM

ref1

(6)

MM

ref2

(6)

DMT0

(1)

/DMT0

(12)

DMT1

(1)

DMT2

(1)

DMT3

(1)

/DMT1

(12)

/DMT2

(12)

/DMT3

(12)

(TM)

(5)

(TM_)

(5)

MRP

S_1

(6)

MRP

S_2

(6)

MRP

S_3

(6)

OUT_B+

(12)

SFTMT0

(3)

/SFTMT0

(12)

SFTMT1

(3)

SFTMT2

(3)

/SFTMT1

(12)

/SFTMT2

(12)

/SFTMT3

(12)

SFTMT3

(3)

SPMT_0

(11)

(SPFMT0)

(5)

SPMT_2

(11)

(SPFMT2)

(5)

(SPFMT3)

(5)

(SPFMT1)

(5)

SPMT_3

(11)

SPMT_1

(11)

TMA_O

(12)

TMB_O

(12)

/SRVC

(11)

SRVC

(3)

(RSV_

SOL)

(3)

/RSV_SOL

(11)

SPU

S(3)

/SPU

S(11)

Sc

an

ne

rM

oto

rD

riv

er

SP

FM

oto

rD

riv

er

Du

ple

xM

oto

rD

riv

er

Sh

ifte

rM

oto

rD

riv

er

To

nn

er

Mo

tor

Dri

ve

r

RS

PF

So

len

oid

Dri

ve

r

IC33

TD62064AF

I13

NC

4

NC

5

I26

NC

10

I311

NC

12

NC

13

GND

17

O1

2

O2

7

O3

9

O4

16

COM

1

COM

8GND

18

I414

NC

15

R161

620J

C140

0.1U/50V

<1608>

CP6

0603

SFF150FM/32-2

C143

0.1U/50V<1608>

R162

1.2KJ

R145

1.5KJ

TP482

TP502

R163

100J

R143

0.68J1W

R159

1.2KJ

C133

820P

TP505

TP489

R146

1.5KJ

R148

30KJ

TP492

Q23

2SD1781K

C138

0.1U

R144

0.68J1W

C135

820P

R147

1KJ

IC31

TD62064AF

I13

NC

4

NC

5

I26

NC

10

I311

NC

12

NC

13

GND

17

O1

2

O2

7

O3

9

O4

16

COM

1

COM

8GND

18

I414

NC

15

R149

30KJ

C134

820P

TP497

R407

10KJ

C136

820P

BR66

10KJX4

1234

8765

IC36

TA7291A

S

Vcc

2

IN1

9

IN2

1

GND

5OUT2

3

OUT1

7

Vref

8

Vs

6

N.C

4

R275

NM_1.2KJ

TP479

+C139

47U/35V

TP481

D8

MTZJ22B

R152

510J

C141

0.1U

TP484

CP1

0603

SFF150FM/32-2

TP503

D41

1S

S355

R157

1J2W

R151

1KJ

C137

0.1U

R408

10KJ

R150

2KJ

TP506

CP2

0603

SFF150FM/32-2

IC34

STA7100MOUTA

1

OUTA

2

OUTA/

3

OUTA/

4

Vs

13

OUTB

17

OUTB

18

OUTB/

15

OUTB/

16

GND

10

INA

8

INA/

7

INB

11

INB/

12

REF

9

Se

nseA

5

Se

nseB

14

Syn

c6

TP478

TP494

R403

1.2KJ

TP488

+C142

10U/35V

TP501

Q24

2SD1781K

TP499

C145

0.1U/50V<1608>

CP5

0603

SFF150FM/32-2

TP480

R312

0J<1608>

IC32

L6219D

S

OUT2A

2

SEN

SE2

3

COMP2

4

OUT2B

5

GND

6

GND

7

I02

8

I12

9

PHA

SE2

10

VREF2

11

RC2

12

VS

S13

RC1

14

VREF1

15

PHA

SE1

16

I11

17

GND

18

GND

19

I01

20

OUT1B

21

COMP1

22

SEN

SE1

23

VS

24

OUT1A

1

R164

4.7KJ

D42

1S

S355

C144

NM_10U/10V<2012>

R160

300J

TP485

TP487

TP504

R404

1.2KJ

Q25

NM_2

SD1781K

R158

1J2W

R406

NM_10KJ

TP491

CP3

0603

SFF150FM/32-2

D43

1S

S355

TP496

R309

NM_0J<1608>

D9

MTZJ22B

TP483

TP477

A A

B B

C C

D D

E E

44

33

22

11

MC

UP

WB

(Dri

ver

sect

ion

3)(A

L-2

050C

S)

7/16


5V

5V 5V

VC

C3

24V

PG

ND

INT

24V

INT

5V

EN

5V

VC

C3

5V 5V

VC

C3

5VV

CC

3

12V

VC

C3

VC

C3

5VINT

24V

PG

ND

PG

ND

VC

C3

VC

C3

SR

JD(1

1)

PO

D(1

2)P

MR

DY

(11)

(SC

OD

)(3

)

(SR

JD)

(3)

(PO

D)

(3)

(PM

RD

Y)

(3)

TC

S(1

6)

MM

LD(1

2)

DV

S1

(3)

(MM

LD)

(3)

(TC

S)

(3)

(MF

D)

(3)

DR

ST

(11)

PS

W(1

1)S

PP

D(1

1)

(PP

D3)

(3)

3.3V

IN(1

1)

DV

SE

L(1

6)

(SP

ID)

(3)

(PP

D2)

(3)

(DR

ST

)(3

)

(SP

PD

)(1

)

(CE

D1)

(3)

CE

D2

(12)

(PS

W)

(1)

PP

D1

(12)

CE

D1

(12)

(CE

D2)

(3)

PP

D2

(12)

(PP

D1)

(3)

PD

1(1

2)P

D2

(12)

(PD

1)(3

)(P

D2)

(3)

SC

OD

(11)

PP

D3

(12)

12V

IN(1

1)

DS

WS

(3)

24V

1(D

SW

S)

(12)

(FA

NLK

)(3

)F

AN

LK(1

2)

SP

ID(1

1)

MF

D(1

2)

(PS

FA

NLK

)(1

)P

SF

AN

LK(1

2)

R18

41K

J

R19

015

KJ

R19

710

J

TP

831

R21

212

KJ

C16

4

0.1U

C19

6

0.1U

/50V

<16

08>

R20

40J

R19

14.

7KJ

R12

510

0KJ

D15

KD

S22

6

213

R21

33.

3KJ

R34

04.

7KJ

TP

508

C18

1

1000

P

C18

6

1000

P

R17

04.

7KJ

D16

KD

S22

6

213

R19

610

J

C16

5

0.1U

R30

510

0J

R20

94.

7KJ

TP

509

C18

7

1000

P

C37

2

1000

P

C17

5

1000

P

TP

517

1

D17

KD

S22

6

213

R17

5

0.22

J 2W

R37

74.

7KJ

R21

04.

7KJ

C16

6

0.1U

C18

8

1000

P

R12

810

0KJ

C18

0

1000

P

C19

9

1000

P

R20

610

0J 2

W

TP

516

1

C14

6

0.1U

C18

9

1000

P

C16

7

0.1U

FB

5N

M_0

J <

1608

>

C18

3

1000

P

C20

2

1000

P

C18

5

1000

P

R21

41K

J

C38

0

1000

P

D63

UDZS3.9B

C20

3

1000

P

C16

8

0.1U

D54

KD

S22

6

213

D21

KD

S22

6

213

TP

510

D10

KD

S22

6

213

R21

51K

J

R18

72.

7KJ

+C

204

22U

/16V

D25

1SS

355

C20

0

1000

P

C14

7

NM

D13

KD

S22

6

213

D22

KD

S22

6

213

IC37

KIA

7805

IN1

GN

D

2

OU

T3

D11

KD

S22

6

213

C18

4

1000

P

C17

4

1000

P

C16

9

0.1U

R21

61K

J

C20

6

0.1U

C20

1

1000

P

D18

KD

S22

6

213

D23

KD

S22

6

213

D12

KD

S22

6

213

R37

21K

J

C20

7

0.1U

R19

410

J

R21

71K

J

C17

0

NM

D24

KD

S22

6

213

R16

815

KJ

R17

24.

7KJ

C14

8

0.1U

+C

205

22U

/16V

C19

3

0.1U

R13

010

0KJ

R19

210

J

R21

81K

J

TP

511

R16

715

KJ

C15

7

NM

+C

192

47U

/35V

R19

81K

J

R21

91K

J

C19

7

0.1U

C17

2

1000

P

R19

91K

J

C14

9

0.1U

C15

8

NM

C17

8

1000

P

D20

KD

S22

6

213

C17

1

1000

P

L5 ZJS

R51

01-2

23T

A

R30

610

0J

R20

20J

R22

01K

J

R17

14.

7KJ

D14

1SS

355

R20

01K

J

C15

9

NM

R21

14.

7KJ

+C

195

22U

/16V

C15

1

NM T

P51

2

R20

11K

J

C15

0

NM

C16

0

0.1U

D37

KD

S22

6

213

C15

2

NM

R20

30J

C18

2

1000

P

C19

8

1000

P

R17

61K

J

C16

1

0.1U

TP

830

R18

520

KJ

D30

KD

S22

6

213

C15

3

NM

R12

610

0KJ

R20

715

KJ

R18

31K

J

D19 1S

S35

5

C17

7

1000

P

R17

71K

J

D31

KD

S22

6

213

TP

513

C15

4

NM

TP

518

1

D28

KD

S22

6

213

R17

81K

J

C17

3

1000

P

+C

194

47U

/25V

+C

190

47U

/35V

D26

KD

S22

6

213

R19

310

J

R17

91K

J 2W

R17

44.

7KJ

C15

5

NM

R18

01K

J

C19

1

0.1U

/50V

<16

08>

D29

KD

S22

6

213

L4 NM

_ZJS

R51

01-2

23T

A

R16

915

KJ D

32

KD

S22

6

213

C15

6

NM

R20

50J

C17

9

0.1U

D27

KD

S22

6

213

R18

11K

J

TP

514

C16

2

0.1U

C17

6

1000

P

R18

81K

J

FB

40J

<16

08>

R12

710

0KJ

R18

21K

J

R19

510

J

R17

315

KJ

R18

91K

J

D62

UDZS3.9B

C16

3

0.1U

R36

71K

J

R20

815

KJ

TP

515

1

R18

620

KJ

A A

B B

C C

D D

E E

44

33

22

11

MC

U P

WB

(N

ois

e fi

lter

/Pu

ll-u

p s

ecti

on

) (A

L-2

050C

S)

8/16


_SDRAM_CLK

SDRAM_DATA0

SDRAM_DATA5

_SDRAM_DQMA0

_SDRAM_CKE

ROM_C

S_L

SDRAM_DQMA1

SDRAM_DATA11

_SDRAM_DQMB1

SDRAM_DATA10

SDRAM_RA

S_L

SDRAM_CKE

XOUT

SDRAM_DATA6

SDRAM_CA

S_L

SDRAM_DATA15

SDRAM_DATA9

SDRAM_C

S0_L

SDRAM_CA

S_L

ROM_C

S_L

_SDRAM_DQMA1

_SDRAM_DQMA1

_SDRAM_DQMB0

SDRAM_DQMB0

SDRAM_WE_L

SDRAM_DQMA0

_SDRAM_DQMA0

SDRAM_BANK0

SDRAM_DATA8

SDRAM_DATA12

SDRAM_DATA14

SDRAM_DATA3

SDRAM_DATA2

SDRAM_DATA4

SDRAM_DATA7

SDRAM_DATA13

SDRAM_BANK1

SDRAM_DQMB1

_SDRAM_C

S0_L

SDRAM_DATA1

TR

ST_L

TCK

TM

S

SDRAM_RA

S_L

SDRAM_WE_L

SDRAM_RA

S_L

SDRAM_CA

S_L

_SDRAM_DQMA0

_SDRAM_C

S0_L

SDRAM_WE_L

_SDRAM_CKE

TDI

CLK_EXT

PB_ADDR3

PB_ADDR0

PB_ADDR6

PB_ADDR1

PB_ADDR4

PB_ADDR7

PB_ADDR5

PB_ADDR2

RY_BY

TDO

PB_DATA4

PB_DATA1

PB_DATA0

PB_DATA5

PB_DATA6

PB_DATA7

PB_DATA2

PB_DATA3

TR

ST_L

TDI

TM

S

TCK

TDO

PIDATA1

PIDATA0

PIDATA2

PIDATA4

RY_BY

PIDATA6

PIDATA7

PIDATA3

PIDATA5

SDRAM_ADDR12

SDRAM_ADDR11

SDRAM_ADDR6

SDRAM_ADDR3

SDRAM_ADDR8

SDRAM_ADDR12

SDRAM_ADDR4

SDRAM_ADDR0

SDRAM_ADDR0

SDRAM_ADDR1

SDRAM_ADDR2

SDRAM_ADDR9

SDRAM_ADDR9

SDRAM_ADDR7

SDRAM_ADDR2

SDRAM_ADDR5

SDRAM_ADDR5

SDRAM_ADDR3

SDRAM_ADDR6

SDRAM_ADDR10

SDRAM_ADDR7

SDRAM_ADDR11

SDRAM_ADDR4

SDRAM_ADDR8

SDRAM_ADDR10

SDRAM_ADDR1

_SDRAM_CKE

_SDRAM_C

S0_L

_SDRAM_DQMA1

/FPOFF

/FPOFF

_SDRAM_DQMB1

SDRAM_BANK0

SDRAM_BANK1

_SDRAM_DATA0

_SDRAM_DATA1

_SDRAM_DATA2

_SDRAM_DATA4

_SDRAM_DATA5

_SDRAM_DATA6

_SDRAM_DATA7

_SDRAM_DATA8

_SDRAM_DATA9

_SDRAM_DATA10

_SDRAM_DATA11

_SDRAM_DATA12

_SDRAM_DATA13

_SDRAM_DATA14

_SDRAM_DATA15

_SDRAM_CLK

_SDRAM_CLK

_SDRAM_DATA3

PODATA4

PODATA5

PODATA7

PODATA6

PODATA3

PODATA2

PODATA1

PODATA0

_SDRAM_DQMB0

SDRAM_ADDR0

SDRAM_ADDR1

SDRAM_ADDR2

SDRAM_ADDR3

SDRAM_ADDR4

SDRAM_ADDR5

SDRAM_ADDR6

SDRAM_ADDR7

SDRAM_ADDR8

SDRAM_ADDR9

SDRAM_ADDR10

SDRAM_ADDR11

SDRAM_ADDR12

SDRAM_BANK0

SDRAM_BANK1

RY_BY

XIN

_SDRAM_DATA3

_SDRAM_DATA1

_SDRAM_DATA7

SDRAM_ADDR5

SDRAM_ADDR6

SDRAM_ADDR8

SDRAM_ADDR9

SDRAM_ADDR11

SDRAM_ADDR12

SDRAM_BANK0

SDRAM_BANK1

_SDRAM_DATA10

_SDRAM_DATA9

_SDRAM_DATA12

_SDRAM_DATA7

_SDRAM_DATA5

_SDRAM_DATA0

SDRAM_RA

S_L

SDRAM_CA

S_L

_SDRAM_CLK

_SDRAM_CLK

_SDRAM_DQMA0

SDRAM_ADDR10

SDRAM_ADDR7

SDRAM_ADDR3 _SDRAM_C

S1A_L

SDRAM_WE_L

SDRAM_ADDR1

SDRAM_ADDR0 _SDRAM_CKE

_SDRAM_DQMA1

SDRAM_ADDR2

SDRAM_ADDR4

_SDRAM_DATA2

_SDRAM_DATA6

_SDRAM_DATA14

_SDRAM_DATA6

_SDRAM_DATA3

_SDRAM_DATA0

_SDRAM_DATA2

_SDRAM_DATA10

_SDRAM_DATA5

_SDRAM_DATA1

_SDRAM_DATA1

_SDRAM_DATA6

_SDRAM_DATA15

_SDRAM_DATA10

_SDRAM_DATA4

_SDRAM_DATA4

_SDRAM_DATA7

_SDRAM_DATA11

_SDRAM_DATA0

_SDRAM_DATA7

_SDRAM_DATA8

_SDRAM_DATA12

_SDRAM_DATA0

_SDRAM_DATA8

_SDRAM_DATA3

_SDRAM_DATA14

_SDRAM_DATA12

_SDRAM_DATA9

_SDRAM_DATA13

_SDRAM_DATA5

_SDRAM_DATA15

_SDRAM_DATA1

_SDRAM_DATA9

_SDRAM_DATA3

_SDRAM_DATA5

_SDRAM_DATA6

_SDRAM_DATA8

_SDRAM_DATA11

_SDRAM_DATA11

_SDRAM_DATA2

_SDRAM_DATA4

_SDRAM_DATA2

_SDRAM_DATA8

_SDRAM_DATA15

_SDRAM_DATA14

_SDRAM_DATA13

_SDRAM_DATA13

_SDRAM_DATA4

_SDRAM_C

S1A_L

SDRAM_C

S1A_L

_SDRAM_C

S1A_L

VCC3

OA3

.3V

OA3.3V

OA3.3V

VCC3

VCC3

VCC3

VCC3

VCC3

VCC3

VCC3

VCC3

VCC3

OA3

.3V

VCC3

VCC3

VCC3

/POACK

(2)

_SDRAM_CLK

CLK_EXT

_SDRAM_CLK

/POREQ

(2)

/SC_LINE

(2)

CLK_EXT

ES_CMD

(1)

ES_

ST

S(1)

DT_REQB

(10)

DT_ACKB

(10)

PB_DATA[7:0]

(10,13)

PB_NC

S1

(13)

PB_ADDR[7:0]

(10,13)

PB_NC

S3

(10)

PB_NAE0

(5,10)

PB_NOE

(5,10)

PB_NWE

(5,10)

/PR_LINE

(2)

/ES_PAGE

(1)

/IMC_READY

(2)

SDRAM_BANK[1:0]

_SDRAM_DATA[15:0]

SDRAM_BANK[1:0]

_SDRAM_DATA[15:0]

SDRAM_ADDR[12:0]

_SDRAM_DATA[15:0]

SDRAM_BANK[1:0]

/ES_CRDY

(3)

INT_U

SBD

(10)

WAKEUP

(10)

SU

SPEND(U

SB2

.0)

(10)

(FW)

(1,5)

SDRAM_ADDR[12:0]

/H_SYNC

(2)

PODATA[7

..0]

(2)

MDM_IRQ

(13)

PIDATA[7

..0]

(2)

/PIREQ

(2)

/PIACK

(2)

/PIWR

(2)

SDRAM_ADDR[12:0]

SDRAM_ADDR[12:0]

TCK

(12)

TM

S(12)

TDI

(12)

/FPOFF

(2)

MODEM_IN

(13)

/RE

SET0

(2,4,5,12)

OA_TX

(12)

OA_RX

(12)

TDO

(12)

VPP

(4)

/ES_

SRDY

(1)

/OP_R

ST

(5,10) /RE

S_OA982

(1)

/RE

SET0

(2,4,5,12)

OA982_READY

(12)

TR

ST_L

(12)

_SDRAM_DATA[15:0]

_SDRAM_CLK

SDRAM_ADDR[12:0]

_SDRAM_DATA[15:0]

SDRAM_BANK[1:0]

8M/16MFla

shROM

TP769

TP567

TP523

C236

0.1U

C265

NM

TP580

C264

0.1U

TP617

R137

33J

FB6

0J<1608>

TP590

R235

33J

BR67

100JX4

1 2 3 45678

C38312PTP911

TP765

TP749

TP573

C227

0.1U

TP733

TP655

TP632

TP613

C237

0.1U

TP524

R233NM

TP761

TP538

C301

0.1U

C303

NM

TP774

TP552

TP779

TP566

TP756

TP607

TP902

TP753

R247

4.7KJ

C209

0.1U

BR76

33JX4

1 2 3 45678

TP663

L6NM_ZJSR5101-223TA

R346

10KJ

TP605

TP595

TP559

C38412P

TP577

TP624

TP600

TP796

TP533

BR77

33JX4

1 2 3 45678

R23110KJ

TP653

TP809

TP659

TP591

BR75

33JX4

1 2 3 45678

R250

4.7KJ

C228

0.1U

C225

0.1U

TP620

R138

NM

TP768

TP532

TP525

R225

33J

BR82

10KJX4

1 2 3 45678

IC40

HY57V561620FTP-H-C

VS

S54

RA

S18

WE

16

CA

S17

VS

S41

VS

S28

VDD

1VDD

14

VDD

27

BA0

20

BA1

21

A0

23

A1

24

A2

25

A3

26

A4

29

A5

30

A6

31

A7

32

A8

33

A9

34

A10

22

A11

35

VDDQ

3VDDQ

9VDDQ

43

VDDQ

49

VS

SQ

6V

SSQ

12

VS

SQ

46

VS

SQ

52

DQ0

2

DQ1

4

DQ2

5

DQ3

7

DQ4

8

DQ5

10

DQ6

11

DQ7

13

DQ8

42

DQ9

44

DQ10

45

DQ11

47

DQ12

48

DQ13

50

DQ14

51

DQ15

53

LDQM

15

UDQM

39

CS

19

CLK

38

CKE

37

A12

36

N.C

40

TP773

TP585

TP546

IC44

HY57V561620FTP-H-C

VS

S54

RA

S18

WE

16

CA

S17

VS

S41

VS

S28

VDD

1VDD

14

VDD

27

BA0

20

BA1

21

A0

23

A1

24

A2

25

A3

26

A4

29

A5

30

A6

31

A7

32

A8

33

A9

34

A10

22

A11

35

VDDQ

3VDDQ

9VDDQ

43

VDDQ

49

VS

SQ

6V

SSQ

12

VS

SQ

46

VS

SQ

52

DQ0

2

DQ1

4

DQ2

5

DQ3

7

DQ4

8

DQ5

10

DQ6

11

DQ7

13

DQ8

42

DQ9

44

DQ10

45

DQ11

47

DQ12

48

DQ13

50

DQ14

51

DQ15

53

LDQM

15

UDQM

39

CS

19

CLK

38

CKE

37

A12

36

N.C

40

TP759

TP582

C242

0.1U

R343

NM_0J

TP645

TP618

R369

NM

TP791

TP780

TP667

C38512P

C248

0.1U

TP925

TP575

TP750

TP592

TP561

TP633

TP614

R239

10KJ

R238

10KJ

C211

NM

C247

0.1U

R227

33J

C249

0.1U

C224

0.1U

TP568

TP930

TP629

TP609

TP787

TP526

TP519

C230

0.1U

C250

0.1U

TP764

TP540 C241

0.1U

R234

33J

TP554

TP664

R232

NM

TP772

TP570

TP560

C38612P

TP926

TP625

TP602

C220

0.1U

TP910

TP597

TP535

TP579

TP654

C299

0.1U

TP660

C219

0.1U

C239

NM

C213

1U<2012>

TP778

TP754

TP728

TP642

TP551

C252

33P

TP621

TP593

TP608

TP527

C235

0.1U

C223

0.1U

R248

4.7KJ

TP757

TP650

TP549

TP901

TP808

TP767

TP656

TP584

R228

33J

TP587

TP668

TP646

TP638

R245

NM

C226

0.1U

TP520

TP547

C215

1U<2012>

TP534

TP762

TP730

TP548

TP563

TP576

TP545

C240

0.1U

TP634

TP615

TP788

R222

33J

R342

4.7KJ

TP601

TP543

C36212P

TP771

TP751

TP569

TP611

TP541

C246

0.1U

BR78

33JX4

1 2 3 45678

C244

0.1U

C216

NM

C100

1000P

C222

0.1U

R246

NM

R229

33J

R236

4.7KJ

TP665

TP539

C253

47P

BR69

100JX4

1 2 3 45678

C395

10U/10V<2012>

TP562

BR81

33JX4

1 2 3 4

8 7 6 5

R249

0J

TP626

TP604

TP572

TP528

TP537

TP760

TP542

R221

NM

TP556

TP661

BR80

33JX4

1 2 3 4

8 7 6 5

C300

0.1U

TP643

C21022000P

R240

10KJ

C36612P

TP599

TP622

TP596

TP912

TP610

TP581

TP529

C251

NM

TP731

TP651

C221

0.1U

TP657

TP586

BR72

33JX4

1 2 3 45678

R243

10KJ

C238

0.1U

TP647

TP639

C218

0.1U

R351

10KJ

C302

0.1U

BR68

100JX4

1 2 3 45678

C214

0.01U

R230NM

TP521

C243

0.1U

TP766

TP565

C245

0.1U

R241

10KJ

X4AT-49(18

.3856MHz)

TP909

TP770

TP755

TP588

TP578

BR71

33JX4

1 2 3 45678

C231

0.1U

C256

0.1U

TP745

TP616

C217

10U/10V<2012>

TP522

C234

0.1U

C396

10U/10V<2012>

TP777

TP536

R242

10KJ

C38112PTP550

IC38

OA-982

GP_C0/PB_ADDR0

199

GP_C1/PB_ADDR1

201

GP_C2/PB_ADDR2

202

GP_C3/PB_ADDR3

203

GP_C4/PB_ADDR4

204

GP_C5/PB_ADDR5

205

GP_C6/PB_ADDR6

207

GP_C7/PB_ADDR7

208

REG_A9/PB_NC

S1

178

REG_A8/PB_NC

S2

180

GP_A1

26

GP_A2/DC_CHY1

28

GP_A3/DC_CHX1

29

GP_A4/DC_PWM1

30

GP_A5/DC_CHY0

31

GP_A6/DC_CHX0

32

GP_A0

24

GP_A7/DC_PWM0

34

GP_B0/U

SART0_TX

1

GP_B1/U

SART0_RX

2

GP_B2/U

SART0_CK

8

GP_B3/ANA_

SD1

9

GP_B4/DT_ACKB

11

GP_B5/DT_REQB

12

GP_B6/DT_ACKA

13

GP_B7/DT_REQA

14

GP_D0/ADC_A0

15

GP_D1/ADC_A1

16

GP_D2/ADC_A2

19

GP_D3/ADC_CLK

21

REG_AD0/PB_DATA0

189

REG_AD1/PB_DATA1

188

REG_AD2/PB_DATA2

187

REG_AD3/PB_DATA3

186

REG_AD4/PB_DATA4

185

REG_AD5/PB_DATA5

183

REG_AD6/PB_DATA6

182

REG_AD7/PB_DATA7

181

REG_ADDR_VALID/PB_NC

S0

190

REG_RD_L/PB_NC

S3

194

REG_WR_L/PB_NAE0

195

REG_C

S_L/PB_NAE1

196

REG_RDY/PB_NWE

197

VS

S_CORE

191

VS

S_IO

150

VS

S_CORE

173

VS

S_IO

136

VS

S_CORE

121

VS

S_IO

123

VS

S_CORE

139

VS

S_CORE

87

VS

S_IO

108

VS

S_CORE

69

VS

S_IO

98

VS

S_CORE

35

VS

S_IO

86

VS

S_CORE

17

VS

S_IO

76

VS

S_IO

64

VS

S_IO

54

VS

S_IO

206

VS

S_IO

41

VS

S_IO

193

VS

S_IO

27

VS

S_IO

10

VS

S_IO

179

VS

S_IO

164

INTERRUPT_L/PB_NOE

198

RE

SET_L

112

TCK

114

TM

S116

TDI

117

TDO

113

BA

SE_CLK/GP_PWM1

168

MAIN_CLK/GP_PWM0

170

CLK_EXT/GP_PWM2

169

TE

ST_MODE0

172

XIN

5

XOUT

4

PP_HIDRIVE/U

SART1_RX

143

PP_DRIVE/U

SART1_TX

145

PP_NINIT

146

PP_NFAULT

147

PP_N

SELECTIN

151

PP_NAUTOFD

152

PP_SELECT

153

PP_PERROR

154

PP_BU

SY

155

PP_NACK

156

PP_DATA7

157

PP_DATA6

159

PP_DATA5

160

PP_DATA4

161

PP_DATA3

162

PP_DATA2

163

PP_DATA1/U

SART1_CK

165

PP_DATA0

166

PP_N

STROBE

167

PO_LINE_SYNC/ANA_SCLK

37

PO_PAGE_

SYNC/ANA_NC

S38

PO_REQ/ANA_

SD0

39

PO_ACK/PDATA0/PD

S0

40

PO_DONE/PDATA2/PD

S2

42

PO_WR/PDATA1/PD

S1

43

PO_DATA7/LHEAT/PA

S_M

44

PO_DATA6/LCTRL/CFIRE2

45

PO_DATA5/AGATE/CFIRE1

47

PO_DATA4/ACLK/MFIRE2

48

PO_DATA3/PENABLE/MFIRE1

49

PO_DATA2/PLOAD

50

PO_DATA1/PCLK

51

PO_DATA0/PDATA3/PA

S_C

52

PI_LINE_SYNC/GP_D6

119

PI_TR_TGEN

120

PI_TGEN6

124

PI_TGEN5

125

PI_TGEN4

126

PI_TGEN3

127

PI_TGEN2

128

PI_TGEN1

129

PI_TGEN0

131

PI_DATA7

132

PI_DATA6

133

PI_DATA5

134

PI_DATA4

135

PI_DATA3

137

PI_DATA2

138

PI_DATA1

141

PI_DATA0

142

SDRAM_DATA15

53

SDRAM_DATA14

55

SDRAM_DATA13

56

SDRAM_DATA12

57

SDRAM_DATA11

58

SDRAM_DATA10

60

SDRAM_DATA9

61

SDRAM_DATA8

62

SDRAM_DATA7

63

SDRAM_DATA6

65

SDRAM_DATA5

66

SDRAM_DATA4

67

SDRAM_DATA3

68

SDRAM_DATA2

72

SDRAM_DATA1

73

SDRAM_DATA0

74

ROM_C

S_L

75

SDRAM_C

S1B_L

77

SDRAM_CKE

78

SDRAM_CLK

79

SDRAM_ADDR11

82

SDRAM_BANK1

83

SDRAM_BANK0

84

SDRAM_ADDR10

85

SDRAM_ADDR9

89

SDRAM_ADDR8

90

SDRAM_ADDR7

91

SDRAM_ADDR6

92

SDRAM_ADDR5

94

SDRAM_ADDR4

95

SDRAM_ADDR3

96

SDRAM_ADDR2

97

SDRAM_ADDR1

99

SDRAM_ADDR0

100

SDRAM_RA

S_L

101

SDRAM_C

S1A_L

102

SDRAM_C

S0_L

104

SDRAM_DQMB1

105

SDRAM_DQMA1

106

SDRAM_DQMB0

107

SDRAM_DQMA0

109

SDRAM_CA

S_L

110

SDRAM_WE_L

111

VDD_IO

144

VDD_CORE

192

VDD_IO

130

VDD_CORE

174

VDD_IO

115

VDD_CORE

140

VDD_IO

103

VDD_CORE

122

VDD_IO

93

VDD_CORE

88

VDD_IO

81

VDD_CORE

70

VDD_IO

71

VDD_CORE

36

VDD_IO

59

VDD_CORE

18

VDD_IO

46

VDD_IO

200

VDD_IO

33

VDD_IO

184

VDD_IO

20

VDD_IO

171

VDD_IO

3

VDD_IO

158

PLLC

S_VDDA

7

PLLC

S_V

SSA

6

SDRAM_ADDR12

80

USB_DP

176

USB_DM

175

PLLS

S_VDDA

149

PLLS

S_V

SSA

148

TE

ST_MODE1

177

TR

ST_L

118

GP_D4/ADC_DATA

22

GP_D5/ADC_NC

S23

VDD_IO

25

TP748

IC39

GND

27

GND

46

VCC

37

IO0

29

IO1

31

IO2

33

IO3

35

IO4

38

IO5

40

IO6

42

IO7

44

IO8

30

IO9

32

IO10

34

IO11

36

IO12

39

IO13

41

IO14

43

IO15/A-1

45

A0

25

A1

24

A2

23

A3

22

A4

21

A5

20

A6

19

A7

18

A8

8

A9

7

A10

6

A11

5

A12

4

A13

3

A14

2

A15

1

A16

48

A17

17

A18

16

VCCW

13

WE

11

RE

SET

12

BYTE

47

CE

26

OE

28

RY/BY

15

A19

9

A20

10

WP/ACC

14

TP571

C212

0.01U

TP631

TP612

TP810

R244

NM_10KJ

BR73

33JX4

1 2 3 45678

TP758

TP752

BR74

33JX4

1 2 3 45678

TP564

TP776

TP732

TP594

TP606

TP557

BR70

100JX4

1 2 3 45678

C263

0.1U

TP666

C233

0.1U

TP574

TP662

BR79

33JX4

1 2 3 45678

TP644

C254

33P

BR83

10KJX4

1 2 3 45678

C38212P

R390

33J

TP669

TP623

TP598

C208

NM

TP530

TP531

TP544

TP652

BR84

10KJX4

1 2 3 45678

TP583

TP558

TP658

TP589

C397

10U/10V<2012>

TP763

TP603

TP648

TP640

TP775

TP744

TP619

C229

0.1U

C232

0.1U

BR85

10KJX4

1 2 3 45678

A A

B B

C C

D D

E E

44

33

22

11

MC

UP

WB

(IM

C2

sect

ion

1/2)

(AL

-205

0CS

)9/

16


PB_NOE

PB_ADDR0

PB_ADDR5

PB_ADDR1

PB_ADDR2

PB_ADDR3

PB_DATA1

PB_DATA0

PB_DATA0

PB_DATA4

PB_DATA4

PB_DATA3

PB_DATA1

PB_DATA7

PB_DATA6

PB_DATA5

PB_DATA3

PB_DATA5

PB_DATA2

PB_DATA7

PB_DATA6

PB_DATA2

PB_ADDR4

PB_ADDR6

PB_ADDR7

PB_NWE

PB_NOE

PB_NWE

FG

ISP33

VCC3

ISP33

VCC3

VCC3

VCC3

VCC3

ISP33

FG

VCC3

VCC3

VCC3

VCC3

VCC3

VCC3

PB_DATA[7:0]

(9,13)

PB_NWE

(5,9)

DT_REQB

(9)

PB_DATA[7:0](9,13)

DT_ACKB

(9)

INT_U

SBD

(9)

PB_NC

S3

(9)

PB_NOE

(5,9)

PB_ADDR[7:0](9,13)

PB_NAE0

(5,9)

/OP_R

ST

(5,9) /RE

S_U

SB20

(1)

SU

SPEND(U

SB2

.0)

(9)

WAKEUP

(9)

DT_ACKB

(9)

GND

GND

GND

USB2.0

DEV1

L130J<1608>

CN1 UBR23-4K2200

-D2

+D

3

SHIELD

5

GND

4

+5V

1

R258

10KJ

C269

0.1U

C404

1U<2012>

TP693

C272

15P

C410

0.1U

TP683

C261

10U/10V<2012>

TP871

IC41

ISP1583B

S

AGND

1

RPU

2

DP

3

DM

4

AGND

5

RREF

6

RE

SET_N

7

EOT

8

DREQ

9

DACK

10

DIOR

11

DIOW

12

DGND

13

INTRQ

14

READY/IORDY

15

INT

16

DA217

CS_N18

RW_N/RD_N19

DS_N/WR_N20

CS0_N21

CS1_N22

AD023

AD124

AD225

VCC(I/O)26

AD327

AD428

AD529

AD630

AD731

VCC1V832

N.C

.33

MODE1

34

DGND

35

ALE/A0

36

DATA0

37

DATA1

38

DATA2

39

DATA3

40

VCC(I/O)

41

DATA4

42

DATA5

43

DATA6

44

DATA7

45

DATA8

46

DATA9

47

DATA10

48

DATA1149

DATA1250

DATA1351

DATA1452

DATA1553

VCC(I/O)54

VBUS55

VCC1V856

XTAL257

XTAL158

DGND59

MODE0/DA160

VCC(3V3)61

BUS_CONF/DA062

WAKEUP63

SUSPEND64

DGNDDIE

R272

12KF

TP704

R259

NM

R139

33J

IC183

TC7

SH126FU

42

1

5 3

TP675

TP677

L7

BLM21PG600

SN1

L9

BLM21PG600

SN1

TP705

TP880

C267

0.1U

R310

NM

R399

100KJ

TP688

TP690

C258

0.01U

TP701

TP686

R257

10KJ

R274

0J

IC43

TC7

SH04FU

24 1

35

C260

0.01U

TP702

TP681

C270

0.1U

C273

18P

TP692

R267

NM_<1608>

C271

0.1U

C262

0.1U

TP682

C266

0.1U

R256

10KJ

TP707

TP706

TP870

TP700

IC42

TC7

SH08FU

1 2 3

4

5

R254

NM

TP703

TP699

C101

1000P

TP709

TP697

R260

10KJ

L8

DLW21

SN900

SQ2

C268

0.1U

TP782

TP696

R40010KJ

TP708

C4030.1U

X6

AT-49(12MHz)

C257

0.01U

L110J<1608>

TP695

C259

0.01U

R261

10KJ

TP907

R111

1MF

TP783

R25210KJ

R40110KJ

R25510KJ

TP908

TP670

C408

0.1U

C4050.1U

R262

1.5KJ

TP694

TP689

TP687

C409

0.1U

TP691

R25110KJ

C406

10U/10V<2012>

TP698

C3700.1U

TP684

R253

1.2KJ

C274

0.01U

TP685

R273

NM

A A

B B

C C

D D

E E

44

33

22

11

MC

UP

WB

(IM

C2

US

B2.

0se

ctio

n2/

2)(A

L-2

050C

S)

10/1

6


5VE

N5V

24V

PG

ND

PG

ND

INT

24V

5V

INT

5V

24V

5VE

N5V

PG

ND

EN

5V5V

VC

C3

5V5V

24V

SP

FM

T

INT

5V

5V

24V

PG

ND

24V

SP

FM

T

5V

5V

24V

SP

FS

OL

/BIA

S(6

)

KE

YIN

(3)

/TC

(6)

/PO

FF

(6)

HLO

UT

(6)

3.3V

IN(8

)

/PR

(6)

FW

(5)

/GR

IDL

(6)

(OP

_CLK

)(5

)

(LC

DD

B6)

(OP

_LA

TC

H)

(5)

12V

IN(8

)

/MC

(6)

DR

ST

(8)

PS

W(8

)

(KE

YS

C1)

(5)

(KE

YS

C2)

(5)

(SE

LIN

1)

(KE

YS

C3)

(5)

(SE

LIN

2)

(LC

DD

B7)

(LC

DD

B5)

(LC

DD

B4)

(LC

DR

S)

BZ

R(1

)

(LC

DE

)

(SE

LIN

3)

INF

OLE

D(3

)

(LC

DC

ON

T)

(6)

SP

MT

_0(7

)S

PM

T_2

(7)

SP

PD

(8)

SP

ID(8

)S

PM

T_3

(7)

SP

MT

_1(7

)

PS

L(3

)

/VID

EO

(5)

SH

OLD

(6)

/SY

NC

(5)

/LD

EN

(6)

PM

CLK

_A(6

)P

MR

DY

(8)

/PM

D(6

)

LCD

RS

#(5

)(L

CD

RS

)

LCD

E#

(5)

(LC

DE

)

LCD

DB

4#(5

)(L

CD

DB

4)

LCD

DB

5#(5

)(L

CD

DB

5)

LCD

DB

6#(5

)(L

CD

DB

6)

LCD

DB

7#(5

)(L

CD

DB

7)

SE

LIN

3(3

)(S

ELI

N3)

SE

LIN

2(3

)(S

ELI

N2)

SE

LIN

1(3

)(S

ELI

N1)

BL

(3)

SP

MT

_0(7

)S

PM

T_2

(7)

SP

ID(8

)S

PM

T_3

(7)

SP

MT

_1(7

)

SP

PD

(8)

SR

JD(8

)

SC

OD

(8)

/SR

VC

(7)

/SP

US

(7)

/RS

V_S

OL

(7)

(OP

_DA

TA

)(5

)

To

Po

wer

un

itT

o O

per

atio

nal

PW

B

To

SP

F u

nit

To

LS

U

(Wh

ite)

To

RS

PF

un

it

To

LD

To

Po

lyg

on

mo

tor

CP8

0603SFF150FM/32-2

R278

200J1/4W<3216>

R349

200J1/4W<3216>

C365NM

CP10

0603SFF150FM/32-2

R32

910

0J

CN

29

B12

B-P

H-K

-S(L

F)(

SN

)

1 2 3 4 5 6 7 8 9 10 11 12

C35

6

100P

C27

5

0.1U

/50V

<16

08>

D33

KD

S22

6

213

C364NM

C2801000P

R29

310

0J

C363NM

D65

KD

S22

6

213

R27

610

KJ

R27

71K

J

C35

8

100P

C36

1

100P

R35

30J

R141

200J1/4W<3216>

R38

5

0J

C35

9

100P

R33

1N

M

R29

510

0J

CN

30

B24

B-P

ND

ZS

-1(L

F)(

SN

)

1 3 5 7 9 11 13 15 17 19 21 23

2 4 6 8 10 12 14 16 18 20 22 24

C27

6

NM

_<16

08>

CP9

0603SFF150FM/32-2

R33

010

0J

R28

21K

JR140

200J1/4W<3216>

C35

7

100P

C34

7

100P

R39

8

0J

CN

41

B05

B-C

ZH

K-B

(LF

)(S

N)(

V)

1 2 3 4 5

CN

2

B24

B-P

ND

ZS

-1(L

F)(

SN

)

1 3 5 7 9 11 13 15 17 19 21 23

2 4 6 8 10 12 14 16 18 20 22 24

CN

3

FF

4-32

-S15

D5

1234567891011121314151617181920212223242526272829303132

R35

00J

C31

7

100P

C34

9

100P

R29

410

0J

R36

510

0J

R32

810

0J

R29

10J

R29

010

0J

R35

2N

M

C2791000P

CN

42

B08

B-C

ZH

K-B

(LF

)(S

N)(

V)

1 2 3 4 5 6 7 8

R34

7N

M_<

1608

>

C2781000P

R29

210

0J

C27

710

00P

C36

0

100P

A A

B B

C C

D D

E E

44

33

22

11

MC

U P

WB

(C

on

nec

tor

sect

ion

1)

(AL

-205

0CS

)11

/16


TCK

/RE

SET0

OA_TX

OA_RX

TCK

/RE

SET0

OA_TX

OA_RX

PGND

PGND

24V

24V

24V

24V

24V

SFTMT

24VDu

pMT

5V

5V

5V

5V

VCC3

INT24V

PGND

24V

PGND

5V

24V

VCC3

VCC3

PGND

PGND

VCC3

VCC3

POD

(8)

/RR

S(6)

PPD1

(8)

PPD2

(8)

TMA_O

(7)

TMB_O

(7)

VFMOUT

(6)

/VFMCNT

(6)

24V1(D

SW

S)

(8)

/SFTMT0

(7)

/SFTMT2

(7)

/SFTMT3

(7)

CED1

(8)

RTH_IN

(6)

/SFTMT1

(7)

/DMT0

(7)

/DMT1

(7)

/DMT2

(7)

/DMT3

(7)

PD1

(8)

/CPF

S1

(6)

/MPF

S(6)

MFD

(8)

/RE

SET0

(2,4,5,9)

TDI

(9)

OA_RX

(9)

OA_TX

(9)

TDO

(9)

TM

S(9)

TR

ST_L

(9)

TCK

(9)

/MMCLK

(6)

MMLD

(8)

/MMD

(6)

/CPF

S2

(6)

CED2

(8)

PPD3

(8)

PD2

(8)

/MCNT

(6)

OUT_A+

(7)

OUT_B-

(7)

OUT_A-

(7)

OUT_B+

(7)

PSFMOUT

(6)

RxD

(1)

TxD

(1)

FANLK

(8)

GA

SIC_READY

(2)

OA982_READY

(9)

PSFANLK

(8)

To

VF

Fan

mo

tor

To

Inte

rlo

ck

sw

itch

To

Cassett

ed

ete

ct

To

Cassett

ep

ap

er

so

len

oid

To

Sh

ifte

rm

oto

r

(Fo

rd

eb

ug

)N

otm

ounte

d

To

To

ner

mo

tor

To

Pap

er

pass

dete

ct

To

Pap

er

ou

td

ete

ct

To

HL

un

it

To

Mu

ltiu

nit

To

Resis

tro

ller

so

len

oid

(Red

)

(Bla

ck)

(Blu

e)

(Red

)

(Red

)

(Wh

ite)

(Wh

ite)

(Wh

ite)

(Wh

ite)

(Wh

ite)

To

Du

ple

xm

oto

r

To

Pap

er

dete

ct

CP

US

eri

al

OA

982

JT

AG

&S

eri

al

To

Main

mo

tor

To

2n

d.cassett

e

To

Mech

a.C

OU

NT

ER

(Red

)

To

Mir

ror

mo

tor

(Wh

ite)

(Wh

ite)

(Wh

ite)

(Gre

en

)

(Wh

ite)

(Red

)

To

PS

Fan

mo

tor

(Wh

ite)

LE

Dfo

rC

hecker

C368

1000P

D40

NM_LT1P67A

TP711

CP21

0J<1608>

D39

NM_LT1P67A

CN15

B3B-PH-K-S(LF)(

SN)

1 2 3

CN18

B3B-PH-K-E(LF)(

SN)

1 2 3

C374

NM_<1608>

CN13

B4B-PH-K-S(LF)(

SN)

1 2 3 4

R287

390J

CN24

B3B-PH-K-R(LF)(

SN)

1 2 3

R284

200J1/4W<3216>

CN26

B3B-PH-K-S(LF)(

SN)

1 2 3

Q9

NM_KRC106S

1

2

3TP714

CN35

NM_B03B-PA

SK-1(LF)(

SN)

123

D38

LT1P67A

CN12

B5B-PA

SK-1(LF)(

SN)

1 2 3 4 5

CN20

B05B-XA

SK-1(LF)(

SN)

1 2 3 4 5

CN27

B5B-PH-K-S(LF)(

SN)

1 2 3 4 5

CN21

B3B-PH-K-K(LF)(

SN)

1 2 3

TP713

R283

200J1/4W<3216>

1/4W

CN19

B14B-PHD

SS-B(LF)(

SN)

1 3 5 7 9 1113

2 4 6 8101214

Q10

NM_KRC106S

1

2

3

R285

200J1/4W<3216>

CN17

B10B-PHD

SS-B(LF)(

SN)

1 3 5 7 9

2 4 6 810

C286

1000P

C373NM

R286

200J1/4W<3216>

C285

1000P

CN28

B3B-PH-K-M(LF)(

SN)

1 2 3

C2830.1U/50V<1608>

C281

1000P

C2840.1U/50V<1608>

C2891000P

TP712

CN16

B4B-PH-K-S(LF)(

SN)

1 2 3 4

CN10

B2P-VH-R(LF)(

SN)

1 2

C2871000P

CN25

B2P-VH(LF)(

SN)

1 2

CN23

NM_B3B-PH-K-R

123

TP710

C282

1000P

CN11

B5B-PH-K-S(LF)(

SN)

1 2 3 4 5

R288

NM

CN14

B5B-PH-K-R(LF)(

SN)

1 2 3 4 5

CN22

B4B-PH-K-R(LF)(

SN)

1 2 3 4

R289

NM

C2881000P

A A

B B

C C

D D

E E

44

33

22

11

MC

UP

WB

(Co

nn

ecto

rse

ctio

n2)

(AL

-205

0CS

)12

/16


#PB_DATA7

#PB_DATA4

#PB_DATA6

#PB_DATA5

PB_NC

S1

(PB_NAE0)

(MDM_IRQ)

(PB_NWE)

(PB_NOE)

MCU_D4

MCU_D3

MCU_D2

MCU_D1

MCU_D6

MCU_D7

MCU_D0

MCU_D5

MODEM_IN

(/RD)

#MDM_IRQ

MCU_INT

MCU_

nC

S

(/FAX_R

ST)

D1D0

D3D2

D7

D5D6

D4

PB_DATA5

PB_DATA7

PB_DATA6

PB_DATA3

PB_DATA0

PB_DATA2

PB_DATA1

#PB_DATA2

PB_DATA4

#PB_DATA1

#PB_DATA3

#PB_DATA0

#PB_ADDR2

#PB_ADDR1

#PB_ADDR0

#PB_ADDR4

PB_ADDR5

PB_ADDR6

#PB_ADDR7

#PB_ADDR5

PB_ADDR1

#PB_ADDR6

#PB_ADDR3

PB_ADDR2

PB_ADDR3

PB_ADDR7

PB_ADDR4

PB_ADDR0

D0

PB_DATA3

D1

PB_DATA0

PB_DATA5

PB_DATA7

D5

(MDM_IRQ)

PB_DATA4

PB_DATA2

MSU_

ST1

PB_DATA6

D4D3D2

D6

PB_DATA1

D7

MCU_D6

MCU_D4

MCU_D0

MCU_D2

MCU_

nC

S

#PB_DATA7

#PB_DATA5

#PB_DATA3

#PB_DATA1

#PB_ADDR7

#PB_ADDR5

#PB_ADDR3

#PB_ADDR1

PB_NC

S1

(PB_NWE)

(/FAX_R

ST)

MODEM_IN

MCU_D7

MCU_D5

MCU_D3

MCU_D1

(/RD)

MCU_INT

#PB_DATA6

#PB_DATA4

#PB_DATA2

#PB_DATA0

#PB_ADDR6

#PB_ADDR4

#PB_ADDR2

#PB_ADDR0

(PB_NAE0)

(PB_NOE)

#MDM_IRQ

VCC3

VCC3

VCC3

24V

EN5V

VCC3

PGND

MDM_IRQ

(9)

PB_NC

S1

(9)

PB_DATA[7:0]

(9,10)

MSU_

ST1

(3)

D[15

..0]

(1,2,3,4)

MODEM_IN

(9)

/CS5

(1)

/FAX_R

ST

(5)

/RE

S_FAX

(1)

(/RD)

(5)

(PB_NWE)

(5)(PB_NOE)

(5)

(PB_NAE0)

(5)

PB_ADDR[7:0]

(9,10)

To

Mo

dem

PW

B

C323NM

C329NM

BR90

33JX4

1234

8765

CP13

0603SFF150FM/32-2

L160J<1608>

C327

10KJ

R315

10KJ

TP903

CP11

0603SFF150FM/32-2

R311

1KJ

D46

KD

S226

213

C321

10KJ

C328NM

BR91

33JX4 1234

8765

BR88

33JX4

1234

8765

BR92

33JX4

1234

8765

R317

1KJ

C325NM

R313

100J

C326

10KJ

TP904

D47

KD

S226

213

BR89

33JX4 1234

8765

C320

10KJ

BR93

33JX4 1234

8765

TP725

CP12

0603SFF150FM/32-2

C337NM

R325

NM

CN5

B40B-PNDZ

S-1(LF)(

SN)

1357911131517192123

24681012141618202224

25

26

27

28

29

30

31

32

33

34

35

36

37

38

39

40

C333

10KJ

C324NM

C335NM

C1020.1U

C334NM

C330

10KJ

C331NM

C336NM

C378

NM

L140J<1608>

R391

100J

C322

10KJ

C332

10KJ

A A

B B

C C

D D

E E

44

33

22

11

MC

UP

WB

(Mo

dem

I/FC

on

nec

tor)

(AL

-205

0CS

)13

/16


VCL

VCL

AFE_DB#0

AFE_DB#3

AFE_DB#4

VCLAFE_DB#6

AFE_DB#1

AFE_DB#2

AFE_DB#5

AFE_DB#7

AFE_DB6

AFE_DB3

AFE_DB4

AFE_DB7

AFE_DB0

AFE_DB5

AFE_DB#1

AFE_DB2

AFE_DB#7

AFE_DB#2

AFE_DB#6

AFE_DB1

AFE_DB#5

AFE_DB#0

AFE_DB#4

AFE_DB#3

AFE_DB2

AFE_DB3

AFE_DB7

AFE_DB5

AFE_DB0

AFE_DB4

AFE_DB1

AFE_DB6

PGND

24V

12V

EN5V

VCC3

PGND

PGND

CL

(2)

AFE_

SCK#

(5)

ADCLK#

(5)

AFE_

SEN#

(5)

AFE_

SDI#

(5)

VSAMP#

(5)

BSAMP#

(5)

mt_

at_

hom

e(5)

CCD_CP#

(5)

CCD_PHI1#

(5)

CCD_R

S#

(5)

CCD_PHI2#

(5)

CCD_TG#

(5)

AFE_DB[7

..0]

(2)

3

21Co

py

La

mp

Inv

ert

er

To

Sc

an

ne

ru

nit

TP886

R318

910J

C340

0.1U/50V<1608>

C132

47P

C313

47P

R321

5.6KJ1/4W<3216>

+C339

47U/35V

C319

47P

D49

11EQ

S06

C314

47P

L12

220UH

TWKA-221K

R323

15KJ

R324

56KJ

C315

47P

CN4

FF4-32-S15D5

135791113151719212325272931

2468101214161820222426283032

C341

33P

Q6

KTC3198

BR8633JX4

1 2 3 4

8 7 6 5

R319

15KJ

C316

47P

R322

12KJ

L17

1J<1608>

CP18

0603

SFF150FM/32-2

C342

1000P

R320

1KJ

BR8733JX4

1 2 3 4

8 7 6 5

D48

KD

S226

213

CP14

0603SFF150FM/32-2

C318

47P

C109

47P

CP15

0603

SFF150FM/32-2

+C338

47U/35V

Q52

SJ537

A A

B B

C C

D D

E E

44

33

22

11

MC

UP

WB

(Sca

nn

erI/F

sect

ion

)(A

L-2

050C

S)

14/1

6


/STB_I

/INIT_I

/ACK_O

BU

SY_O

/FAULT_O

SLCT_O

/REV_O

/SLCTIN_I

/AUTOFD_I

PE_O

PARAD7

PARAD3

PARAD5

PARAD4

PARAD6

PARAD1

PARAD0

PARAD2

VCC3

EN5V

EN5V

VCC3

PARAD[7

..0]

(2)

/REV_O

(2)

/FAULT_O

(2)

SLCT_O

(2)

PE_O

(2)

BU

SY_O

(2)

/ACK_O

(2)

/NIC_R

ST

(5)

/RE

S_NIC

(1)

/INIT_I

(2)

/SLCTIN_I

(2)

/AUTOFD_I

(2)

/STB_I

(2)

To

NIC

PW

B

C39012P

C345

0.1U

CP19

0603SFF150FM/32-2

TP674

C39112P

L18

0J<1608>

C346

0.1U

TP680

TP905

C39212P

BR9433JX4

1 2 3 4

8 7 6 5

CP20

0603SFF150FM/32-2

CN39

24FMN-BTK-A

123456789101112131415161718192021222324

R326

1KJ

TP676

C39312P

R327

NM

L19

0J<1608>

C39412P

BR9533JX4

1 2 3 4

8 7 6 5TP717

C343

0.1U

TP906

TP678

C344

0.1U

C1060.1U

C38712P

TP672

R402

NM

C38812P

TP679

C38912P

TP673

A A

B B

C C

D D

E E

44

33

22

11

MC

UP

WB

(NIC

I/Fse

ctio

n)

(AL

-205

0CS

)15

/16


EN5V

VCC3

EN5V

PGND

EN5V

24V

24V

(CRUM

SDA)

CRUM

SDA

(1)

/ASIC_R

ST

(5)

(CRUM

SDA)

(CRUM

SCL)

TC

S_AN

(6)

TC

S(8)

DV

SEL

(8)

CRUM

SCL

(1)

(CRUM

SCL)

5V

CR

UM

Co

ntr

ol

3.3

V

3.3

V

5V F-GND1

F-GND2

F-GND3

F-GND4

F-GND5

To

DV

Un

itw

ith

CR

UM

(To

An

alo

gT

on

ne

rS

en

so

r)

(Wh

ite)

(Red

)

To

DV

Un

it

(To

An

alo

gT

on

ne

rS

en

so

r)

F-GND6

F-GND7

R279

10J

FB15

0J

orCHIPINDUCTER(NM)<1608>

FB14

0J


TP884

D34

KD

S226

213

R281

300J

C350

0.1U

R335

10KJ

D35

KD

S226

213

R280

300J

R334

NM

FB11

0J


FB10

0J


R348

NM

FB12

0J


IC51

TC7SET08F

1 2 3

4

5

FB9

0J


FB8

0J


IC49

TC7SBD385AFU

A1

B2

OE

4GND

3

Vcc

5

B10B-PHD

SS-B(LF)(

SN)

CN7

1 3 5 7 9

2 4 6 810

CN6

NM_B4B-PH-K-R

1 2 3 4

R341

10KJ

R337

0J

TP721

TP715

TP887

TP883

C348

0.1U

A A

B B

C C

D D

E E

44

33

22

11

MC

UP

WB

(CR

UM

I/Fse

ctio

n)

(AL

-205

0CS

)16

/16


4. OPERATION PWB (AL-2050CS)

LCD

RS

#

LCD

DB

7#

LCD

DB

4#

LCD

DB

6#

LCD

RS

#

LCD

E#

LCD

E#

LCD

DB

7#

LCD

DB

4#

LCD

DB

6#

LCD

DB

5#LC

DD

B6

LCD

DB

7

LCD

DB

4LCD

DB

5#

LCD

DB

5

5VE

N

5VE

N

3.3V

3.3V

5V

LED

_V2

OP

-CLK

OP

-DA

TA

OP

-LA

TC

H

LED

_V3

LED

_V1

DA

TA

1

LCD

E

LCD

RS

LCD

DB

[7..4

]

LCD

CO

NT

PS

L

To

LCD

FAX

SCAN

COPY

PRINT

SPFL

HPL

SJAL

BPL

CS1L

CS2L

RPL

PSL

R33

310

0JR

333

100J

TP14 TP14

LTL-

1LH

G-0

02A

LED

308

LTL-

1LH

G-0

02A

LED

308

IC30

4

TB

6272

5AF

IC30

4

TB

6272

5AF

/OUT27

/OUT38

/OUT49

/OUT510

/OUT611

/OUT16

/OUT05 VCC 16

/ENABLE 13

/LATCH 4

S-IN 2

CLOCK 3

S-OUT 14

GND 1/OUT712

R-EXT 15

TP

1T

P1

LTL-

1LH

G-0

02A

LED

309

LTL-

1LH

G-0

02A

LED

309

C32

3

open

C32

3

open

Q30

7

KR

C10

6S

Q30

7

KR

C10

6S

1

2

3

TP

3T

P3

TP5 TP5

R30

210

0JR

302

100J

C329100pC329100p

R30

50JR

305

0J

R34

410

0JR

344

100J

LTL-

1LH

G-0

02A

LED

311

LTL-

1LH

G-0

02A

LED

311

TP

15T

P15

TP6 TP6

C330100pC330100p

LTL-

1LH

G-0

02A

LED

301

LTL-

1LH

G-0

02A

LED

301

R33

210

0JR

332

100J

LTL-

1LH

G-0

02A

LED

306

LTL-

1LH

G-0

02A

LED

306

TP

2T

P2

R33

50J

R33

50J

C332100pC332100p

R32

50JR

325

0J

R30

410

0JR

304

100J

R30

147

0JR

301

470J

C32

2

0.1u

C32

2

0.1u

LTL-

1LH

G-0

02A

LED

310

LTL-

1LH

G-0

02A

LED

310

R32

310

KJ

R32

310

KJ

C30

6

1000

p

C30

6

1000

p

OP

EN

LED

303

OP

EN

LED

303

R33

110

0JR

331

100J

TP10 TP10

LTL-

1LH

G-0

02A

LED

302

LTL-

1LH

G-0

02A

LED

302

IC30

1

GP

M18

1C0

IC30

1

GP

M18

1C0

GN

D1

0

V5

9

VD

D8

RS

7

R/W

6

E5

DB

44

DB

53

DB

62

DB

71

R32

782

0JR

327

820J

C3330.1u C3330.1u

Q30

5K

RA

225S

Q30

5K

RA

225S

3

2

1

TP9 TP9

LTL-

1LH

G-0

02A

LED

307

LTL-

1LH

G-0

02A

LED

307

Q30

3K

RA

225S

3

2

1

R30

6O

PE

NR

306

OP

EN

TP13 TP13

C331100pC331100p

R33

010

0JR

330

100J

Q30

4K

RA

225S

3

2

1

TP

11T

P11

LTL-

1LH

EE

-002

A

LED

304

LTL-

1LH

EE

-002

A

LED

304

LTL-

1LH

G-0

02A

LED

305

LTL-

1LH

G-0

02A

LED

305

TP8 TP8

TP

4T

P4

R33

410

0JR

334

100J

R32

40JR

324

0J

C30

5

1000

p

C30

5

1000

p

C327100pC327100p

R30

310

0JR

303

100J

LTL-

1LH

G-0

02A

LED

314

LTL-

1LH

G-0

02A

LED

314

C30

8

Ope

n

C30

8

Ope

n

Q30

2

KR

C10

6S

Q30

2

KR

C10

6S

1

2

3

D30

4

ZE

NE

R_3

.3V

D30

4

ZE

NE

R_3

.3V

R32

910

0JR

329

100J

C30

7

open

C30

7

open

R32

810

kJR

328

10kJ

C328100pC328100p

TP12 TP12

C3380.1u C3380.1u

TP7 TP7

R32

60JR

326

0J

A A

B B

C C

D D

E E

44

33

22

11

OP

ER

AT

ION

PW

B(L

ED

/LC

Dse

ctio

n)

(AL

-205

0CS

)1/

3


5V

5V

5VE

N

5V

KE

YS

C1

KE

YS

C2

KE

YS

C3

KE

YIN

SE

LIN

3S

ELI

N2

SE

LIN

1

PS

W

F-K

EY

SC

2F

-KE

YS

C3

F-K

EY

SC

1

F-K

EY

IN1

F-K

EY

IN2

F-K

EY

IN3

F-K

EY

IN4

F-K

EY

IN5

F-K

EY

IN6

F-K

EY

IN7

BZ

R

CAK

NM6K

NM1K

NM8K

RAT

ENT

LK

MODK

BPK

MENU

RK

NM7K

SHPK

NM4K

NM2K

CLK

NM3K

NM5K

NM9K

NM0K

ASTK

EXP

ESRT

2SIDE

PSW

R31

210

0JR

312

100J

R34

3

2kJ

R34

3

2kJ

KE

Y31

5

SK

QN

AB

D01

0

KE

Y31

5

SK

QN

AB

D01

0

TP

26T

P26

R31

71k

J

KE

Y30

6

SK

QN

AB

D01

0

KE

Y30

6

SK

QN

AB

D01

0

R33

910

kJR

339

10kJ

KE

Y32

1

SK

QN

AB

D01

0

KE

Y32

1

SK

QN

AB

D01

0

C31

7

Ope

n

C31

7

Ope

n

R30

710

0JR

307

100J

C30

9

Ope

n

TP

36T

P36

C31

9

Ope

n

TP

29T

P29

R31

310

0JR

313

100J

TP

24T

P24

TP

17T

P17

BZ

301

PS

1720

P02

BZ

301

PS

1720

P02

1

2

C33

4

Ope

n

C33

4

Ope

n

KE

Y32

5

SK

QN

AB

D01

0

KE

Y32

5

SK

QN

AB

D01

0

R30

910

0JR

309

100J

KE

Y30

7

SK

QN

AB

D01

0

KE

Y30

7

SK

QN

AB

D01

0

C31

0

Ope

nC31

8

Ope

n

TP

25T

P25

TP

33T

P33

KE

Y32

2

SK

QN

AB

D01

0

KE

Y32

2

SK

QN

AB

D01

0

KE

Y31

3

SK

QN

AB

D01

0

KE

Y31

3

SK

QN

AB

D01

0

TP

19T

P19

KE

Y30

2

SK

QN

AB

D01

0

KE

Y30

2

SK

QN

AB

D01

0

D30

2

1SS

133

D30

2

1SS

133

R31

833

JR

318

33J

R33

81k

J

C31

1

Ope

n

KE

Y32

4

SK

QN

AB

D01

0

KE

Y32

4

SK

QN

AB

D01

0

C31

6

Ope

n

C31

6

Ope

n

TP

21T

P21

R32

1

2kJ

R32

1

2kJ

KE

Y31

9

SK

QN

AB

D01

0

KE

Y31

9

SK

QN

AB

D01

0

TP

35T

P35

TP

28T

P28

R33

61k

J

R34

0

2kJ

R34

0

2kJ

KE

Y32

0

SK

QN

AB

D01

0

KE

Y32

0

SK

QN

AB

D01

0

KE

Y32

3

SK

QN

AB

D01

0

KE

Y32

3

SK

QN

AB

D01

0D

303

1SS

133

D30

3

1SS

133

R31

51k

J

R30

810

0JR

308

100J

KE

Y30

8

SK

QN

AB

D01

0

KE

Y30

8

SK

QN

AB

D01

0

R31

110

0JR

311

100J

C32

0

Ope

n

KE

Y31

8

SK

QN

AB

D01

0

KE

Y31

8

SK

QN

AB

D01

0

KE

Y31

2

SK

QN

AB

D01

0

KE

Y31

2

SK

QN

AB

D01

0

KE

Y30

1

SK

QN

AB

D01

0

KE

Y30

1

SK

QN

AB

D01

0

TP

31T

P31

TP

32T

P32

KE

Y31

0

SK

QN

AB

D01

0

KE

Y31

0

SK

QN

AB

D01

0

D30

1

1SS

133

D30

1

1SS

133

TP

23T

P23

R34

2

2kJ

R34

2

2kJ

KE

Y30

3

SK

QN

AB

D01

0

KE

Y30

3

SK

QN

AB

D01

0

C33

5

Ope

n

C33

5

Ope

n

R32

0

2kJ

R32

0

2kJ

R32

2

2kJ

R32

2

2kJ

KE

Y31

4

SK

QN

AB

D01

0

KE

Y31

4

SK

QN

AB

D01

0

IC30

2

74H

C15

1

IC30

2

74H

C15

1

D0

4

D1

3

D2

2

D3

1

D4

15

D5

14

D6

13

D7

12

A1

1

B1

0

C9

G7

W6

Y5

VC

C1

6

GN

D8

KE

Y31

7

SK

QN

AB

D01

0

KE

Y31

7

SK

QN

AB

D01

0

R31

9

2kJ

R31

9

2kJ

C33

6

Ope

n

C33

6

Ope

n

TP

16T

P16

TP

34T

P34

C32

1

0.1u

TP

27T

P27

R3482kJ

C30

4

Ope

n

C30

4

Ope

n

TP

18T

P18

KE

Y31

1

SK

QN

AB

D01

0

KE

Y31

1

SK

QN

AB

D01

0

R31

61k

J

R33

71k

J

TP

20T

P20

R31

410

0JR

314

100J

R3472kJ

Q30

6

KR

C10

6S

Q30

6

KR

C10

6S

1

2

3

C31

3

Ope

n

C31

3

Ope

n

C31

5

47pF

TP

30T

P30

R34

1

2kJ

R34

1

2kJ

KE

Y30

9

SK

QN

AB

D01

0

KE

Y30

9

SK

QN

AB

D01

0

R3462kJ

KE

Y30

5

SK

QN

AB

D01

0

KE

Y30

5

SK

QN

AB

D01

0

C33

7

Ope

n

C33

7

Ope

n

KE

Y31

6

SK

QN

AB

D01

0

KE

Y31

6

SK

QN

AB

D01

0

R31

010

0JR

310

100J

IC30

3

74H

C23

8

IC30

3

74H

C23

8

GN

D8

Y0

15

Y1

14

Y2

13

Y3

12

Y4

11

Y5

10

Y6

9

Y7

7

A1

B2

C3

G2

B5

G2

A4

G1

6

VC

C1

6

TP

22T

P22

C31

4

Ope

n

C31

4

Ope

n

KE

Y30

4

SK

QN

AB

D01

0

KE

Y30

4

SK

QN

AB

D01

0

C31

2

0.1u

C31

2

0.1u

A A

B B

C C

D D

E E

44

33

22

11

OP

ER

AT

ION

PW

B(K

EY

/Bu

zzer

sect

ion

)(A

L-2

050C

S)

2/3


DR

ST

DR

ST

LCD

DB

5

LCD

DB

7

LCD

DB

4

LCD

DB

6

3.3V

5V5V

EN

PS

LP

SW

KE

YIN

OP

-CLK

OP

-LA

TC

H

OP

-DA

TA

SE

LIN

1S

ELI

N2

KE

YS

C2

KE

YS

C3

LED

_V3

F-K

EY

IN1

BZ

RK

EY

SC

1

LCD

RS

LCD

E

SE

LIN

3

LCD

DB

[7..4

]F

-KE

YIN

4

DA

TA

1

F-K

EY

IN2

LED

_V2

F-K

EY

IN5

LED

_V1

F-K

EY

SC

2

F-K

EY

IN6

F-K

EY

SC

3

F-K

EY

SC

1F

-KE

YIN

7

F-K

EY

IN3

LCD

CO

NT

ToM

CU

PW

B

ToD

rum

Initi

alD

etec

tor

ToFA

XK

eyP

WB

TP

43T

P43

TP

51T

P51

C30

3

47uF

/16v

TP

42T

P42

C32

6

0.1u

TP

50T

P50

TP

41T

P41

TP

49T

P49

CN

301

BM

15B

-GH

S-T

BT

1 2 3 4 5 6 7 8 9 10

11

12

13

14

15

TP

57T

P57

CN

302

32F

MN

-BM

TT

R-A

-TB

CN

302

1 2 3 4 5 6 7 8 9 10

11

12

13

14

15

16

17

18

19

20

21

22

23

24

25

26

27

28

29

30

31

32

R352Open

TP

48T

P48

C30

2

47uF

/16v

TP

56T

P56

TP

40T

P40

TP

52T

P52

TP

39T

P39

TP

54T

P54

TP

47T

P47

TP

55T

P55

TP

38T

P38

C32

4

0.1u

TP

46T

P46

TP

53T

P53

TP

37T

P37

TP

45T

P45

TP

44T

P44

C30

1

47uF

/16v

C32

5

0.1u

CN

303

S3B

-PH

-K-S

1 2 3

A A

B B

C C

D D

E E

44

33

22

11

OP

ER

AT

ION

PW

B(C

on

nec

tor

sect

ion

)(A

L-2

050C

S)

3/3


LEAD-FREE SOLDER

The PWB’s of this model employs lead-free solder. The “LF” marks indicated on the PWB’s and the Service Manual mean “Lead-Free” solder.

The alphabet following the LF mark shows the kind of lead-free solder.

(1) NOTE FOR THE USE OF LEAD-FREE SOLDER THREAD

When repairing a lead-free solder PWB, use lead-free solder thread.

Never use conventional lead solder thread, which may cause a breakdown or an accident.

Since the melting point of lead-free solder thread is about 40°C higher than that of conventional lead solder thread, the use of the exclusive-usesoldering iron is recommendable.

(2) NOTE FOR SOLDERING WORK

Since the melting point of lead-free solder is about 220°C, which is about 40°C higher than that of conventional lead solder, and its soldering capacity isinferior to conventional one, it is apt to keep the soldering iron in contact with the PWB for longer time. This may cause land separation or may exceedthe heat-resistive temperature of components. Use enough care to separate the soldering iron from the PWB when completion of soldering isconfirmed.

Since lead-free solder includes a greater quantity of tin, the iron tip may corrode easily. Turn ON/OFF the soldering iron power frequently.

If different-kind solder remains on the soldering iron tip, it is melted together with lead-free solder. To avoid this, clean the soldering iron tip aftercompletion of soldering work.

If the soldering iron tip is discolored black during soldering work, clean and file the tip with steel wool or a fine filer.

Example:

5mm

Lead-Free

Solder compositioncode (Refer to thetable at the right.)

<Solder composition code of lead-free solder>

Solder composition

Sn-Ag-Cu

Sn-Ag-BiSn-Ag-Bi-Cu

Sn-Zn-Bi

Sn-In-Ag-Bi

Sn-Cu-Ni

Sn-Ag-Sb

Bi-Sn-Ag-PBi-Sn-Ag

a

b

z

i

n

s

p

Solder composition code

a

CAUTION FOR BATTERY REPLACEMENT

(Danish) ADVARSEL !Lithiumbatteri – Eksplosionsfare ved fejlagtig håndtering.

Udskiftning må kun ske med batteriaf samme fabrikat og type.

Levér det brugte batteri tilbage til leverandoren.

(English) Caution !Danger of explosion if battery is incorrectly replaced.

Replace only with the same or equivalent typerecommended by the manufacturer.

Dispose of used batteries according to manufacturer’s instructions.

(Finnish) VAROITUSParisto voi räjähtää, jos se on virheellisesti asennettu.

Vaihda paristo ainoastaan laitevalmistajan suosittelemaantyyppiin. Hävitä käytetty paristo valmistajan ohjeiden

mukaisesti.

(French) ATTENTIONIl y a danger d’explosion s’ il y a remplacement incorrect

de la batterie. Remplacer uniquement avec une batterie dumême type ou d’un type équivalent recommandé par

le constructeur.Mettre au rebut les batteries usagées conformément aux

instructions du fabricant.

(Swedish) VARNINGExplosionsfara vid felaktigt batteribyte.

Använd samma batterityp eller en ekvivalenttyp som rekommenderas av apparattillverkaren.

Kassera använt batteri enligt fabrikantensinstruktion.

(German) AchtungExplosionsgefahr bei Verwendung inkorrekter Batterien.

Als Ersatzbatterien dürfen nur Batterien vom gleichen Typ odervom Hersteller empfohlene Batterien verwendet werden.Entsorgung der gebrauchten Batterien nur nach den vom

Hersteller angegebenen Anweisungen.

CAUTION FOR BATTERY DISPOSAL

(For USA, CANADA)"BATTERY DISPOSAL"

THIS PRODUCT CONTAINS A LITHIUM PRIMARY(MANGANESS DIOXIDE) MEMORY BACK-UP BATTERY

THAT MUST BE DISPOSED OF PROPERLY. REMOVE THEBATTERY FROM THE PRODUCT AND CONTACT YOUR

LOCAL ENVIRONMENTAL AGENCIES FOR INFORMATIONON RECYCLING AND DISPOSAL OPTIONS.

"TRAITEMENT DES PILES USAGÉES"CE PRODUIT CONTIENT UNE PILE DE SAUVEGARDE DE

MÉMOIRE LITHIUM PRIMAIRE (DIOXYDE DE MANGANÈSE)QUI DOIT ÊTRE TRAITÉE CORRECTEMENT. ENLEVEZ LAPILE DU PRODUIT ET PRENEZ CONTACT AVEC VOTRE

AGENCE ENVIRONNEMENTALE LOCALE POUR DESINFORMATIONS SUR LES MÉTHODES DE RECYCLAGE ET

DE TRAITEMENT.

COPYRIGHT © 2008 BY SHARP CORPORATIONAll rights reserved.Printed in Japan.

No part of this publication may be reproduced,stored in a retrieval system, or transmitted,

in any form or by any means,

electronic; mechanical; photocopying; recording or otherwisewithout prior written permission of the publisher.

Trademark acknowledgements• Microsoft®, Windows®, Windows® 98, Windows® Me, Windows® 2000,

Windows® XP, Windows® Vista and Internet Explorer® are registered trademarks or trademarks of Microsoft Corporation in the U.S.A. and other countries.

• Adobe®, the Adobe® logo, Acrobat®, the Adobe® PDF logo, and ReaderTM are registered trademarks or trademarks of Adobe Systems Incorporated in the United States and other countries.

• IBM, PC/AT, and PowerPC are trademarks of International Business Machines Corporation.

• Sharpdesk is a trademark of Sharp Corporation.

• All other trademarks and copyrights are the property of their respective owners.

SHARP CORPORATIONDigital Document System GroupCS Promotion CenterYamatokoriyama, Nara 639-1186, Japan

2008 February Printed in Japan

Date post:	13-Jan-2015
Category:	Technology
Upload:	julio-davinson-quintero-fonseca
View:	2,571 times
Download:	6 times

61168147 manual-de-servicio-sharp-al-2030-2040cs-2050cs

Technology