of 20
8/12/2019 6505+ manual
1/20
8/12/2019 6505+ manual
2/20
IMPORTANT SAFETY INSTRUCTIONS
WARNING:When using electrical products, basic cautions should always be followed, including the following:
1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
5. Do not use this apparatus near water.
6. Clean only with a dry cloth.
7. Do not block any of the ventilation openings. Install in accordance with manufacturers instructions.
8. Do not install near any heat sources such as radiators, heat registers, stoves or other apparatus (including amplifiers) that
produce heat.
9. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than
the other. A grounding type plug has two blades and a third grounding plug. The wide blade or third prong is provided for your
safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet.
10. Protect the power cord from being walked on or pinched, particularly at plugs, convenience receptacles, and the point they exit
from the apparatus.
11. Only use attachments/accessories provided by the manufacturer.
12. Use only with a cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is
used, use caution when moving the cart/apparatus combination to avoid injury from tip-over.
13. Unplug this apparatus during lightning storms or when unused for long periods of time.
14. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such
as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has
been exposed to rain or moisture, does not operate normally, or has been dropped.
15. Never break off the ground pin. Write for our free booklet Shock Hazard and Grounding. Connect only to a power supply of the
type marked on the unit adjacent to the power supply cord.
16. If this product is to be mounted in an equipment rack, rear support should be provided.
17. Note for UK only: If the colors of the wires in the mains lead of this unit do not correspond with the terminals in your plug
proceed as follows: a) The wire that is colored green and yellow must be connected to the terminal that is marked by the letter
E the earth symbol colored green or colored green and yellow. b) The wire that is colored blue must be connected to the
terminal that is marked with the letter N or the color black. c) The wire that is colored brown must be connected to the terminal
that is marked with the letter L or the color red.
18. This electrical apparatus should not be exposed to dripping or splashing and care should be taken not to place objects
containing liquids, such as vases, upon the apparatus.
19. The on/off switch in this unit does not break both sides of the primary mains. Hazardous energy can be present inside thechassis when the on/off switch is in the off position. The mains plug or appliance coupler is used as the disconnect device, the
disconnect device shall remain readily operable.
20. Exposure to extremely high noise levels may cause a permanent hearing loss. Individuals vary considerably in susceptibility to
noise-induced hearing loss, but nearly everyone will lose some hearing if exposed to sufficiently intense noise for a sufficient
time. The U.S. Governments Occupational Safety and Health Administration (OSHA) has specified the following permissible
noise level exposures:
Duration Per Day In Hours Sound Level dBA, Slow Response 8 90
6 92
4 95
3 97
2 100
1 12 102 1 105
12 110
14 or less 115
According to OSHA, any exposure in excess of the above permissible limits could result in some hearing loss. Earplugs or protectors to
the ear canals or over the ears must be worn when operating this amplification system in order to prevent a permanent hearing loss, if
exposure is in excess of the limits as set forth above. To ensure against potentially dangerous exposure to high sound pressure levels, it is
recommended that all persons exposed to equipment capable of producing high sound pressure levels such as this amplification system be
protected by hearing protectors while this unit is in operation.
SAVE THESE INSTRUCTIONS!
8/12/2019 6505+ manual
3/20
8/12/2019 6505+ manual
4/20
WICHTIGE SICHERHEITSHINWEISE
SICHERHEITSHINWEISEACHTUNG: Beim Einsatz von Elektrogerten mssen u.a. grundlegende Vorsichtsmanahmen befolgt werden:
1. Lesen Sie sich diese Anweisungen durch.
2. Bewahren Sie diese Anweisungen auf.
3. Beachten Sie alle Warnungen.
4. Befolgen Sie alle Anweisungen.
5. Setzen Sie dieses Gert nicht in der Nhe von Wasser ein.
6. Reinigen Sie es nur mit einem trockenen Tuch.
7. Blockieren Sie keine der Lftungsffnungen. Fhren Sie die Installation gem den Anweisungen des Herstellers durch.
8. Installieren Sie das Gert nicht neben Wrmequellen wie Heizungen, Heizgerten, fen oder anderen Gerten (auch Verstrkern),die Wrme erzeugen.
9. Beeintrchtigen Sie nicht die Sicherheitswirkung des gepolten Steckers bzw. des Erdungssteckers. Ein gepolter Stecker weist zweiStifte auf, von denen einer breiter ist als der andere. Ein Erdungsstecker weist zwei Stifte und einen dritten Erdungsstift auf. Der breiteStift bzw. der dritte Stift dient Ihrer Sicherheit. Sollte der beiliegende Stecker nicht in Ihre Steckdose passen, wenden Sie sich bitte aneinen Elektriker, um die ungeeignete Steckdose austauschen zu lassen.
10. Schtzen Sie das Netzkabel, sodass niemand darauf tritt oder es geknickt wird, insbesondere an Steckern oder Buchsen und ihrenAustrittsstellen aus dem Gert.
11. Verwenden Sie nur die vom Hersteller erhltlichen Zubehrgerte oder Zubehrteile.
12. Verwenden Sie nur einen Wagen, Stativ, Dreifu, Trger oder Tisch, der den Angaben des Herstellers entspricht oder zusammen
mit dem Gert verkauft wurde. Wird ein Wagen verwendet, bewegen Sie den Wagen mit dem darauf befindlichen Gert besondersvorsichtig, damit er nicht umkippt und mglicherweise jemand verletzt wird.
13. Trennen Sie das Gert whrend eines Gewitters oder whrend lngerer Zeitrume, in denen es nicht benutzt wird, von derStromversorgung.
14. Lassen Sie smtliche Wartungsarbeiten von qualifizierten Kundendiensttechnikern durchfhren. Eine Wartung ist erforderlich, wenndas Gert in irgendeiner Art beschdigt wurde, etwa wenn das Netzkabel oder der Netzstecker beschdigt wurden, Flssigkeit oderGegenstnde in das Gert gelangt sind, das Gert Regen oder Feuchtigkeit ausgesetzt wurde, nicht normal arbeitet oder herunt-ergefallen ist.
15. Der Erdungsstift darf nie entfernt werden. Auf Wunsch senden wir Ihnen gerne unsere kostenlose Broschre Shock Hazard andGrounding (Gefahr durch elektrischen Schlag und Erdung) zu. Schlieen Sie nur an die Stromversorgung der Art an, die am Gertneben dem Netzkabel angegeben ist.
16. Wenn dieses Produkt in ein Gerte-Rack eingebaut werden soll, muss eine Versorgung ber die Rckseite eingerichtet werden.
17. Hinweis Nur fr Grobritannien: Sollte die Farbe der Drhte in der Netzleitung dieses Gerts nicht mit den Klemmen in Ihrem
Stecker bereinstimmen, gehen Sie folgendermaen vor: a) Der grn-gelbe Draht muss an die mit E (Symbol fr Erde) markiertebzw. grne oder grn-gelbe Klemme angeschlossen werden. b) Der blaue Draht muss an die mit N markierte bzw. schwarze Klemmeangeschlossen werden. c) Der braune Draht muss an die mit L markierte bzw. rote Klemme angeschlossen werden.
18. Dieses Gert darf nicht ungeschtzt Wassertropfen und Wasserspritzern ausgesetzt werden und es muss darauf geachtet werden,dass keine mit Flssigkeiten gefllte Gegenstnde, wie z. B. Blumenvasen, auf dem Gert abgestellt werden.
19. Der Netzschalter in dieser Einheit bricht beide Seiten von den primren Haupleitungen nicht. Gerfhrliche Energie kann anwesendinnerhalb des Chassis sein, wenn her Netzschalter im ab Poistion ist. Die Hauptleitungen stpseln zu oder Gertkupplung ist benutzt,whrend das Vorrichtung abschaltet, das schaltet Vorrichtung wird bleiben sogleich hantierbar ab.
20. Belastung durch extrem hohe Lrmpegel kann zu dauerhaftem Gehrverlust fhren. Die Anflligkeit fr durch Lrm bedingtenGehrverlust ist von Mensch zu Mensch verschieden, das Gehr wird jedoch bei jedem in gewissem Mae geschdigt, der bereinen bestimmten Zeitraum ausreichend starkem Lrm ausgesetzt ist. Die US-Arbeitsschutzbehrde (Occupational and Health
Administration, OSHA) hat die folgenden zulssigen Pegel fr Lrmbelastung festgelegt:
Dauer pro Tag in Stunden Geruschpegel dBA, langsame Reaktion
8 90
6 92 4 95
3 97
2 100
1 12 102
1 105
12 110
14 oder weniger 115
Laut OSHA kann jede Belastung ber den obenstehenden zulssigen Grenzwerten zu einem gewissen Gehrverlust fhren. Sollte die Belastungdie obenstehenden Grenzwerte bersteigen, mssen beim Betrieb dieses Verstrkungssystems Ohrenstopfen oder Schutzvorrichtungen imGehrgang oder ber den Ohren getragen werden, um einen dauerhaften Gehrverlust zu verhindern. Um sich vor einer mglicherweisegefhrlichen Belastung durch hohe Schalldruckpegel zu schtzen, wird allen Personen empfohlen, die mit Gerten arbeiten, die wie diesesVerstrkungssystem hohe Schalldruckpegel erzeugen knnen, beim Betrieb dieses Gerts einen Gehrschutz zu tragen.
BEWAHREN SIE DIESE SICHERHEITSHINWEISE AUF!
8/12/2019 6505+ manual
5/20
Intended to alert the user to the presence of uninsulated dangerous voltage within the products enclosure that may be of sufcientmagnitude to constitute a risk of electric shock to persons.
Intended to alert the user of the presence of important operating and maintenance (servicing) instructions in the literature accompanying
the product.
CAUTION: Risk of electrical shock DO NOT OPEN!
CAUTION: To reduce the risk of electric shock, do not remove cover. No user serviceable parts inside. Refer servicing to qualied servicepersonnel.
WARNING:To prevent electrical shock or re hazard, this apparatus should not be exposed to rain or moisture and objects lled withliquids such as vases should not be placed on this apparatus. Before using this apparatus read the operating guide for further warnings.
Tarkoitettu kiinnittmn kyttjn huomio sellaiseen eristmttmn vaaralliseen jnnitteeseen tuotteen kotelossa, joka saattaa ollariittvn suuri aiheuttaakseen shkiskuvaaran.
Tarkoitettu kiinnittmn kyttjn huomio trkeisiin kytt- ja huolto-ohjeisiin tuotteen mukana seuraavassa ohjeistuksessa.
VAROITUS: Shkiskun vaara L AVAA!
VAROITUS: Shkiskuvaaran vuoksi l poista kantta. Ei sisll kyttjn huollettavissa olevia osia. Huoltaminen tulee jtt ptevnhuoltohenkilstn tehtvksi.
VAARA: Shkiskun tai tulipalon vaaran estmiseksi tt laitetta ei saa altistaa sateelle tai kosteudelle, eik sen plle saa asettaanesteell tytettyj esineit, kuten maljakoita. Ennen laitteen kytt lue muut varoitukset kyttohjeesta.
Ce symbole est utilis dans ce manuel pour indiquer lutilisateur la prsence dune tension dangereuse pouvant tre damplitude
sufsante pour constituer un risque de choc lectrique.
Ce symbole est utilis dans ce manuel pour indiquer lutilisateur quil ou quelle trouvera dimportantes instructions concernant lutilisation
et lentretien de lappareil dans le paragraphe signal.
ATTENTION:Risques de choc lectrique NE PAS OUVRIR!
ATTENTION:An de rduire le risque de choc lectrique, ne pas enlever le couvercle. Il ne se trouve lintrieur aucune pice pouvanttre repare par lutilisateur. Conez Ientretien et la rparation de lappareil un rparateur Peavey agr.
AVIS: Dans le but de reduire les risques dincendie ou de decharge electrique, cet appareil ne doit pas etre expose a la pluie ou a lhumiditeet aucun objet rempli de liquide, tel quun vase, ne doit etre pose sur celui-ci. Avant dutiliser de cet appareil, lisez attentivement le guidefonctionnant pour avertissements supplmentaires.
r avsedd att varna anvndaren fr frekomsten av oisolerad farlig spnning inom produktens hlje som kan vara av tillrcklig niv fr attpersoner ska riskera elektrisk stt.
r avsedd att uppmrksamma anvndaren p frekomsten av viktiga handhavande- och underhllsinstruktioner (service) i den litteratursom medfljer produkten.
OBSERVERA:Risk fr elektrisk stt PPNA INTE!
OBSERVERA:Fr att minska risken fr elektrisk stt, avlgsna inte hljet. Inga delar inuti kan underhllas av anvndaren. Lt kvaliceradservicepersonal skta servicen.
VARNING:Fr att frebygga elektrisk stt eller brandrisk br apparaten inte utsttas fr regn eller fukt, och freml fyllda med vtskor,ssom vaser, br inte placeras p denna apparat. Ls bruksanvisningen fr ytterligare varningar innan denna apparat anvnds.
Dieses Symbol soll den Anwender vor unisolierten gefhrlichen Spannungen innerhalb des Gehuses warnen, die von AusreichenderStrke sind, um einen elektrischen Schlag verursachen zu knnen.
Dieses Symbol soll den Benutzer auf wichtige Instruktionen in der Bedienungsanleitung aufmerksam machen, die Handhabung undWartung des Produkts betreffen.
VORSICHT:Risiko Elektrischer Schlag! Nicht ffnen!
VORSICHT:Um das Risiko eines elektrischen Schlages zu vermeiden, nicht die Abdeckung enfernen. Es benden sich keine Teile darin,die vom Anwender repariert werden knnten. Reparaturen nur von qualiziertem Fachpersonal durchfhren lassen.
WARNUNG:Um elektrischen Schlag oder Brandgefahr zu verhindern, sollte dieser Apparat nicht Regen oder Feuchtigkeit ausgesetztwerden und Gegenstnde mit Flssigkeiten gefuellt, wie Vasen, nicht auf diesen Apparat gesetzt werden. Bevor dieser Apparat verwendetwird, lesen Sie bitte den Funktionsfhrer fr weitere Warnungen.
Este smbolo tiene el propsito, de alertar al usuario de la presencia de (voltaje) peligroso sin aislamiento dentro de la caja del productoy que puede tener una magnitud suciente como para constituir riesgo de descarga elctrica.
Este smbolo tiene el propsito de alertar al usario de la presencia de instruccones importantes sobre la operacin y mantenimiento en la
informacin que viene con el producto.
PRECAUCION:Riesgo de descarga elctrica NO ABRIR!
PRECAUCION:Para disminur el riesgo de descarga elctrica, no abra la cubierta. No hay piezas tiles dentro. Deje todo mantenimientoen manos del personal tcnico cualicado.
ADVERTENCIA:Para prevenir choque electrico o riesgo de incendios, este aparato no se debe exponer a la lluvia o a la humedad. Losobjetos llenos de liquidos, como los oreros, no se deben colocar encima de este aparato. Antes de usar este aparato, lea la guia defuncionamiento para otras advertencias.
8/12/2019 6505+ manual
6/20
6505+ 112 ComboGuitar Amplifier
After forging the sound of aggression for more than 15 years, Peavey is making its highly respected, high-gain 6505Series
amplifier available for the first time in a 1x12 combo-amp configuration. The new 6505 Plus 112 combo harnesses the full gainand legendary tone of the Peavey 6505 Series, which since 1991 has defined the sounds of extreme rock guitar, into a formatthat is equally suited to clubs, rehearsal rooms and studios. Five select 12AX7 preamp tubes and a pair of 6L6GC power-amptubes provide the tonal foundation for the 6505 Plus 112 combo, while patented circuitry such as Peavey's Resonance controltweak its legendary tone. Both the Lead and Rhythm channels feature independent three-band EQ, pre/post gain controlsand Presence and Resonance adjustment. The Rhythm channel also includes a footswitchable Crunch boost. The 6505 Plus112 combo also features the Peavey MSDImicrophone-simulated direct interface, which eliminates the need for miking byallowing users to route the amp's signal directly to a recording device or mixing console. Additional features include three-spring reverb, effects loop and external speaker outputs, plus a 12" Sheffieldloudspeaker in a sealed-back cabinet that offersmaximum resonance and sound projection.
Before you begin playing through your amplifier, it is very important to ensure that the product has the proper AC line voltagesupplied. You can find the proper voltage for your amp printed next to the IEC line (power) cord on the rear panel of the unit.
Each product feature is numbered. Refer to the front panel diagram in this manual to locate the particular features next to itsnumber.
Please read this guide carefully to ensure your personal safety as well as the safety of your amplifier.
FEATURES:
60 watts RMS
16, 8 or 4 ohms
Five 12AX7 preamp tubes and two 6L6GC power-amp tubes
Effects loop
Separate three-band EQ on each channel
Separate Resonance and Presence controls on each channel
Separate pre/post gain on each channel
Footswitchable Crunch boost on Rhythm channel
Three-spring reverb
MSDImicrophone-simulated XLR direct output
12" Sheffieldloudspeaker
External speaker outputs
Lighted Peavey logo with dimmer control
ENGLISH
8/12/2019 6505+ manual
7/20
1 2 3 4 5 6 7 8 9 10 11 12
POWER SWITCHThis two-way switch applies mains power to the unit.
STANDBY SWITCHThis two-way switch allows the amp to be placed in the STANDBY mode. In the STANDBY position the tubesstay hot but the amplifier is not operational. Switching to the ON position places the amp in active mode.
LEAD CHANNEL PRESENCE CONTROLAdjusts the high-frequency damping factor of the power amplifier, which gives the amp a "mellow" characte
when fully counterclockwise and more of "biting" or forward character when rotated clockwise.
LEAD CHANNEL RESONANCE CONTROLAdjusts the low-frequency damping factor of the power amplifier, which gives the amp a "tighter" soundwhen fully dialed counterclockwise and an increasingly "looser" sound when adjusted clockwise.
RHYTHM CHANNEL PRESENCE CONTROLAdjusts the high-frequency damping factor of the power amplifier, which gives the amp a "mellow" charactewhen fully counter-clockwise and more of "biting" or forward character when rotated clockwise.
RHYTHM CHANNEL RESONANCE CONTROLAdjusts the low-frequency damping factor of the power amplifier, which gives the amp a "tighter" soundwhen fully dialed counter clockwise and an increasingly "looser" sound when adjusted clockwise.
MASTER REVERB CONTROLControls the amount of spring reverb in the signal chain.
LEAD CHANNEL POST CONTROLThis control adjusts the volume of the Lead channel.
HIGH CONTROLThis passive control regulates the high frequencies for the Lead channel.
MID CONTROLThis passive control regulates the mid frequencies for the Lead channel.
LOW CONTROLThis passive control regulates the low frequencies for the Lead channel.
PRE GAIN CONTROLAdjusts the amount of gain in the Lead channel. Turning this knob clockwise will increase the amount ofdistortion present in the signal.
LEAD CHANNEL INDICATOR LIGHTThis light is on when the Lead channel is active.
Front Panel
1
2
3
4
5
6
7
8
9
10
11
12
13
13
8/12/2019 6505+ manual
8/20
Front Panel
RHYTHM CHANNEL POST CONTROLThis control adjusts the volume of the Rhythm channel.
HIGH CONTROLThis passive control regulates the high frequencies for the Rhythm channel.
MID CONTROLThis passive control regulates the mid frequencies for the Rhythm channel.
LOW CONTROLThis passive control regulates the low frequencies for the Rhythm channel.
RHYTHM CHANNEL CRUNCH SWITCHEngaging this switch turns on the Crunch effect, increasing the amount of distortion present in thesignal on the Rhythm channel.
PRE GAIN CONTROLAdjusts the amount of gain in the Rhythm channel. Turning this knob clockwise will increase the amountof distortion present in the signal.
RHYTHM CHANNEL INDICATOR LIGHTThis light is on when the Rhythm channel is active.
CHANNEL SWITCHSwitches between the Rhythm and Lead channels.
INPUT JACK1/4" instrument input jack.
15
16
17
18
19
20
21
22
1514 16 17
18
19
20
21 22
14
8/12/2019 6505+ manual
9/20
EFFECTS LOOP1/4" Send and Return jacks for the effects loop.
CABINET IMPEDANCE SELECTOR SWITCHThis three-position switch allows appropriate selection of speaker cabinet impedance. If two loudspeakerenclosures of equal impedance are used, the switch should be set to half the individual value. For example,two 16-ohm enclosures necessitate an 8-ohm setting, while two 8-ohm enclosures would require a 4-ohmsetting. Minimum speaker impedance is 4 ohms. The stock setting for the internal speaker is 16 ohms.
SPEAKER OUTPUTSThese paralleled 1/4" mono (TS) jacks are provided for the connection of speaker enclosure(s). Again,
minimum speaker impedance is 4 ohms. The CABINET IMPEDANCE SWITCH (24) should be set to match theload of the speaker cabinet(s).
MSDIMicrophone Simulated Direct Interface. Peavey's exclusive MSDI simulates the sound of a microphoneplaced approximately 8" from loudspeaker cone, allowing the user to send a clean signal to the mixingconsole. This is a non-powered output and safe for use with any mixing console.
GROUND LIFTEngage this switch if the mix engineer is hearing a hum in the MSDI output This should eliminate the hum.
FOOTSWITCH1/4" input for the optional footswitch.
FUSEA fuse is located within the cap of the fuse holder. This fuse must be replaced with one of the same typeand value to avoid damaging the amplifier and voiding the warranty. If the amp repeatedly blows the fuse, itshould be taken to a qualified service center for repair.WARNING: THE FUSE SHOULD ONLY BE REPLACED AFTER THE POWER CORD HAS BEEN DISCONNECTED.
IEC MAINS CONNECTORThis is a standard IEC power connector. An AC mains cord having the appropriate AC plug and ratings for theintended operating voltage is included in the carton. The mains cord should be connected to the amplifierbefore connecting to a suitable AC outlet.
U.S DOMESTIC AC MAINS CORDThe mains cord supplied with the unit is a heavy-duty, 3-conductor type with a conventional 120 VAC plugwith ground pin. If the outlet used does not have a ground pin, a suitable grounding adapter should be
used, and the third wire should be grounded properly.
Never break off the ground pin on any euipment. It is provided for your safety.
NOTE: FOR UK ONLYIf the colors of the wires in the mains lead of this unit do not correspond with the colored markingsidentifying the terminals in your plug, proceed as follows: (1) The wire that is colored green and yellow mustbe connected to the terminal that is marked by the letter E, the Earth symbol, colored green, or coloredgreen and yellow. (2) The wire that is colored blue must be connected to the terminal that is marked withthe letter N or the color black. (3) The wire that is colored brown must be connected to the terminal that ismarked with the letter L or the color red.
Rear Panel
23
28
29
24
25
26
27
30
23 25
24
26 27 28 29 30
8/12/2019 6505+ manual
10/20
FOOTSWITCH
CHANNEL SWITCHSelects between the Rhythm and Lead channels.
EFFECTS SWITCHActivates the Rhythm channel Crunch boost.
31
32
8/12/2019 6505+ manual
11/20
Preamp Input: Impedance: 1 ohms
Nominal Sensitivity (Rhythm): -32.8dBV, 23.0m (rMS)Nominal Sensitivity (Lead): -63.5dBV, 667uV (rms)
Crunch Boost (Clean channel only): Increased gain and altered reponse for very brown voicing.
Eualization (both channels) Custom Low, Mid & High EQ.
Effects Return: Load Impedance: 22k ohms or greater
Nominal Output Level: -3.0dBV, 0.7V (rms)
(MSDI) Microphone Simulated Direct Interface: Load Impedance: 6k ohms or greater
Nominal Output Level: -29.1dBV, 35.0V (rms)
Remote Footswitch: (optional) Special two-button unit with LED indicators (not included,
Peavey #00592720) for channel selection (Channel) andremote activation of the Crunch boost (BOOST).
6505+112 Combo Specications
NOTE: The following specifications were measured with all preamp controls set at "5"(Crunch "out"); Post Gains set at "10," Reverb, Resonance and Presence all set at "0."
Preamp Specifications
Rated Power & Load: 60 W(rms) into 4, 8, or 16
(selectable)
Power Consumption: 150W, 60 Hz, 120 VAC (Domestic)
150W, 50/60 Hz, 220-240 VAC (Export)
Tube Complement: 2 x 6L6GC, 5 x 12AX7/ECC83
Dimensions (H x W x D):
22.3"(567mm) x 25.5" (648mm) x 11.2" (285mm)Weight: 64.2 lbs. (29.1 kg)
6505+ 112 Combo
NOTE:Specifications subject to change without notice.
8/12/2019 6505+ manual
12/20
6505+ 112 ComboGuitar Amplifier
Apres avoir forg le son de lagressivit pendant plus de 15 ans, Peavey apporte sur le march une nouvelle version inspire
de la clbre srie haut gain universellement connue sous le nom de 6505, pour la premier fois un combo 1X12. Le nouveaucombo 6505+ 112 sonne avec le mme full gain et tonalit que tous les amplis de la srie 6505, qui depuis 1991 a dfini lessonorits du rock guitaristique extrme, dans un format pratique, transportable, pour les clubs, salles de rptitions et studiosCinq lampes 12AX7 slectionnes pour le prampli plus une paire de 6L6GC pour la partie puissance donnent au 6505 +112 lapersonnalit fondamentale que lon sattend entendre tandis que les circuits brevets tell que Peaveys Rsonance controlcontribuent au son lgendaire. Les canaux Lead et Rythme ont chacun une qualisation trois bandes indpendante, pr/postgain, contrles Prsence et Rsonance. Le canal rythmique inclus galement un contrle au pied du boost Crunch. Le 6505Plus 112 inclus aussi une interface directe de simulation de microphone MSDI qui limine le besoin davoir un micro extrieuret ainsi passer directement dans la console ou lenregistreur. Dans les caractristiques figurent aussi une rverb trois ressorts,boucle deffets, et sortie extension baffle additionnel, plus un HP Sheffield log dans un baffle ferm qui offre un maximum deprojection et de chaleur.
Avant que vous ne commenciez utiliser votre amplificateur cest trs important de vrifier que votre produit et quip du bonAC voltage. Vous pouvez trouver la rfrence du voltage imprim cot du IEC (puissance) sur le panneau arrire de lampli.
Chaque produit est numrot. Rfrez vous au diagramme qui est appos sur le panneau avant qui est dans ce manuel pourlocaliser les particularits de chaque fonction.
Sil vous plait lisez attentivement ce guide pour votre scurit et celle de votre ampli.
CARACTRISTIqUES:
60 watts RMS
16, 8 ou 4 ohms Cinq lampes 12AX7 section prampli et deux lampes 6L6GC section puissance
Boucle deffets
EQ trois bandes indpendants sur chaque canal
Contrles Rsonance et Prsence indpendants sur chaque canal
Pr/post gain indpendant sur chaque canal
Boost Crunch activable par pdalier sur le canal Rythme
Rverb trois ressorts
MSDIsimulation microphone XLR sortie directe
Haut parleur 12 (31cm) Sheffield
Sortie HP externe
Logo Peavey lumineux avec contrle attnuateur
FRANAIS
8/12/2019 6505+ manual
13/20
1 2 3 4 5 6 7 8 9 10 11 12
INTERRUPTEUR DALIMENTATIONCet interrupteur contrle la mise en tension de lunit.
INTERRUPTEUR STAND-BYCet interrupteur permet la mise en stand-by de lunit. Slectionner sur ON permet de mettre lampli enmode actif.
CONTRLE DE PRSENCE SUR CANAL LEADAjuste les hautes frquences du facteur damortissement de lamplificateur de puissance qui donnera un
caractre sonore Moelleux quand compltement tourn dans la sens contraire des aiguilles de montre et aucontraire plus agressif dans le sens des aiguilles.
CONTRLE DE RSONANCE SUR LE CANAL LEADAjuste les basses frquences du facteur damortissement de lamplificateur de puissance qui donnera uncaractre sonore un son serr quand compltement tourn sens contraire des aiguilles de montre et aucontraire un son baveux quand tourn dans le sens normal des aiguilles de montre.
CONTRLE DE PRSENCE SUR LE CANAL RYTHMEAjuste les hautes frquences du facteur damortissement de lamplificateur de puissance qui donnera uncaractre sonore Moelleux quand compltement tourn dans la sens contraire des aiguilles de montre et aucontraire plus agressif dans le sens des aiguilles.
CONTRLE DE RSONANCE SUR LE CANAL RYTHME
Ajuste les basses frquences du facteur damortissement de lamplificateur de puissance qui donnera uncaractre sonore un son serr quand compltement tourn sens contraire des aiguilles de montre et aucontraire un son baveux quand tourn dans le sens normal des aiguilles de montre.
CONTRLE MASTER REVERBContrle la quantit de rverb ressorts dans la chane du signal
CONTRLE POST CANAL LEADCe contrle ajuste le volume du canal Lead
CONTRLE DES AGUESCe contrle passif rgule les hautes frquences du canal Lead
CONTRLE DES MDIUMSCe contrle passif rgule les frquences mdium du canal Lead
CONTRLE DES BASSESCe contrle passif rgule les frquences basses du canal Lead
CONTRLE PR -GAINAjuste la quantit de gain dans le canal Lead. Tourner ce bouton dans le sens des aiguilles de montreaugmentera la distorsion prsente dans le signal.
INDICATEUR LUMINEUx CANAL LEADCette lumire est active quand le canal Lead est actif
Front Panel
1
2
3
4
5
6
7
8
9
10
11
12
13
13
8/12/2019 6505+ manual
14/20
Front Panel
CONTRLE POST CANAL RYTHMECe contrle ajuste le volume du canal Rythme
CONTRLE DES AIGUSContrle passif de rgulation des hautes frquences pour le canal Rythme
CONTRLE DES MEDIUMSContrle passif de rgulation des frquences mdium pour le canal Rythme
CONTRLE DES BASSESContrle passif de rgulation des frquences basses pour le canal Rythme
INTERRUPTEUR CRUNCH SUR CANAL RYTHMEEngager cet interrupteur met en fonction leffet Crunch, augmentant ainsi la quantit de distorsionprsente sur le canal Rythme
CONTRLE PRE GAINAjuste la quantit de gain sur le canal Rythme. En tournant ce bouton dans le sens des aiguilles demontre on augmente le montant de distorsion prsent dans le signal
INDICATEUR LUMINEUx DU CANAL RYTHMEQuand le canal Rythme est actif lindicateur lumineux est allum
COMMUTATEUR DE CANAUxCommute les canaux Lead & Rythme.
JACK ENTRE1/4" instrument Jack dentre
15
16
17
18
19
20
21
22
1514 16 17
18
19
20
21 22
14
8/12/2019 6505+ manual
15/20
BOUCLE DEFFETS1/4" Jack Envoi et retour pour la boucle deffets
SLECTEUR DIMPDANCE DES BAFFLESle slecteur trois positions rgit limpdance des haut parleurs. Si deux hauts parleurs (baffles) dgalesimpdances sont utiliss, le slecteur devra tre positionn sur la moiti de chaque valeur. Par exempledeux baffles 16 - ohms ncessiteront un rglage sur 8-ohms, alors que deux baffles 8-ohms ncessiteront unrglage sur 4-ohms. La valeur ne pas dpasser (minimum) est 4-ohms. Maximum 16-ohms.
SORTIE HAUT - PARLEURCes sorties jack 1/4 mono (TS) sont ddies une connexion additionnelle de baffle(s). Encore une fois,
limpdance minimum est 4 ohms et le slecteur dimpdance de baffles devra tre rgl sur la bonnevaleur.
MSDILinterface Direct de Simulation Micro Peavey MSDI simule le son dun micro plac approximativement 8"(~2,50 m) du baffle, cela permet lutilisateur denvoyer un signal clair dans la console. Cest une sortiepassive et scurise pour un usage courant avec nimporte quelle console de mixage.
INTERRUPTEUR GROUND LIFTEngager cet interrupteur si lingnieur son entend un hum dans MSDI.
FOOTSWITCH JACK1/4" d'entre pour la pdale optionnelle.
FUSIBLEUn fusible est positionn dans le porte fusible. Ce fusible doit tre remplac par exactement un du mmetype et de mme valeur sous peine dendommager lamplificateur et de perdre la garantie. Si le fusiblesavrait sauter en permanence, lampli devrait dans ce cas tre emmen dans un centre technique agrepour rparation.
ATTENTION:Le fusible doit tre remplac uniuement aprs ue le cordon secteur dalimentation ait tdconnect.
IEC CONNECTEURS DE PUISSANCEConnecteur standard de puissance. Ce connecteur reli au cble secteur doit tre connect laprise secteur adapte.
U.S DOMESTIC AC MAINS CORDBroche 3 conducteurs avec prise conventionnelle 220V nantie dune prise de terre. Si votre prisemaison na pas de prise de terre, un adaptateur prise de terre doit tre utilis et le troisime filmont proprement.
Ne dsengagez jamais la prise de terre daucun uipement. Cest votre scurit.
NOTE: FOR UK ONLYIf the colors of the wires in the mains lead of this unit do not correspond with the colored markings identifying theterminals in your plug, proceed as follows: (1) The wire that is colored green and yellow must be connected to theterminal that is marked by the letter E, the Earth symbol, colored green, or colored green and yellow. (2) The wirethat is colored blue must be connected to the terminal that is marked with the letter N or the color black. (3) Thewire that is colored brown must be connected to the terminal that is marked with the letter L or the color red.
Rear Panel
23
28
29
24
25
26
27
30
23 25
24
26 27 28 29 30
8/12/2019 6505+ manual
16/20
FOOTSWITCH
SLECTEUR DE CANAUxSlectionne le canal Rythme ou Lead.
SLECTEUR BOOSTActive le boost Crunch sur la canal Rythme
31
32
8/12/2019 6505+ manual
17/20
Pr-ampli Input: Impdance: 1 ohms
Sensibilit Nominale (Rhythm): -32.8dBV, 23.0m (rms)
Sensibilit Nominale (Lead): -63.5dBV, 667uV (rms)
Crunch Boost (Canal Clair uniuement): Augmente le gain et altre la rponse pour un voicing
beaucoup plus chaud.
Eualization (deu cannau) Custom Low, Mid & High EQ.
Effets Return: Load Impedance: 22k ohms or greater
Nominal Output Level: -3.0dBV, 0.7V (rms)
(MSDI) Interface de simulation Microphone Load Impedance: 6k ohms or greater
Nominal Output Level: -29.1dBV, 35.0V (rms)
Pdalier: (optionnel)Pdalier deux boutons avec LED (optionnel, pas inclus
Peavey# 00592720) pour slection de canaux et activation
distance du booster de Crunch.
Spcifications 6505+112 Combo
NOTE: Les spcifications suivantes ont t mesures avec tous les contrles du pramplirgls "5" ( Crunch out) Post gain "10", Rverbe, Rsonance et Prsence rgls "10".
Preamp Specifications
Puissance & Impdances 60 W(rms) into 4, 8, or 16
(slectionnable)
Consommation de puissance: 150W, 60 Hz, 120 VAC (USA)
150W, 50/60 Hz, 220-240 VAC (Export)
Lampes: 2 x 6L6GC, 5 x 12AX7/ECC83
Dimensions (H W D):
22.3"(567mm) x 25.5" (648mm) x 11.2" (285mm)Poids: 29.1 kg (64.2 lbs.)
6505+ 112 Combo
NOTE:Spcifications sujettes changement sans pravis.
8/12/2019 6505+ manual
18/20
8/12/2019 6505+ manual
19/20
U.S. CUSTOMER WARRANTY REGISTRATION
Optional Product Extended Warranty RegistrationGive us some information and put your extended warranty into effect!
9.How would you describe your level of musicianship/technical expertise
1.
First Name Initial Last Name
Street Address
City State/Province Postal Code
( )
Telephone Number E-mail Address
( ) - -
Fax Number Date of birth
2.
Model Serial #
Date of Purchase Price Paid
3.
Name of store where purchased
City State
4.Top two (2) reasons why you purchased from this store/dealer:
8.Which other brands/models did you consider?
Past favorable experience
Best price
Advertised special
Convenient location
Received as a gift
Other
Availability of product
Friend/Relatives recommendation
Store credit card
Knowledgeable staff
Availability of lessons
Technical instruction
6.What two (2) factors most influenced your purchase of this product?
Peavey brand name
Craftsmanship Features for price
Bundled accessories
Sound quality
Product appearance
Durability Prior experience with Peavey
Packaging
Other
Beginner - Never played or taken less than one (1) year of lessons
Intermediate - One (1) to five (5) years of lessons or playingAdvanced - More than five (5) years of lessons or playing; play professio
10.Education: (select best answer)
High school
Some college
Completed college Graduate school
Gender M F
11.Which best describe your family income? (select best answer)
12.Which of the following is your primary source of information on music
products: (select best answer)
Please take a few minutes to fill out this information/survey sheet to help us get to know and serve you better.
To save time, submit your warranty registration online at www.peavey.com/support/warrantyregistration
Under $15,000
$15,000 - $24,999
$25,000 - $34,999 $35,000 - $49,999
$50,000 - $74,999
Television
Radio
Internet Newspaper
Magazines
Mail order catalogs
Direct mail
Literature from manufacturer Other
$75,000 - $99,999
$100,000 - $149,999
Over - $150,000
13.What is your main motivation for buying new equipment?
Replacing old product Want new and leading edge
equipment
Fullfill a specific need Supplement existing products
Value
Impulse Need for improved performanc
New technology
Availability of product Other
7.How did you learn about this Peavey product? (select best answer)
Magazine review
Newspaper review
Radio advertisement
Advertised special Friend/Relatives recommendation Salespersons recommendation
Teachers recommendation
Catalog or flyer
Saw in store
Use by professional Other
15.In your opinion, what could Peavey do to improve its products and/or service? Please use the space below to tell us your answer.
Thank you for taking the time to fill out our survey! Dont forget to fold and tape
(with Peavey address facing out), affix postage stamp and drop in the mail!
5.Where do you most often shop for music and sound products?
Independent retailer
Mass market retailer Mail order magazines
Newspaper ads
Internet/Web sites Other
Revised 1/11
14.Please list your three most frequently visited Web sites.
1. http://__________________________________________
2. http://__________________________________________
3. http://__________________________________________
Logo referenced in Directive 2002/96/EC An(OJ(L)37/38,13.02.03 and defined in EN 504
The bar is the symbol for marking of new wis applied only to equipment manufacture
13 August 2005
8/12/2019 6505+ manual
20/20
PeaveyElectronics
Corporation
Attn:WarrantyDepartment
P.O.Box5108
Meridian,Ms39302-5108
Postage
Here
