REED MANUFACTURING COMPANY 1425 West Eighth St. Erie, PA 16502 USA PHONE: 800-666-3691 or 814-452-3691 Fax: 800-456-1697 or 814-455-1697 www.reedmfgco.com 700PD Power Drive • Automate the pipe threading process • Dropheads available separately in sizes from 1/2” to 2”. The REED 700PD Power Drive is a portable, electric-motor-driven, heavy-duty power drive which provides power for threading pipe and conduit up to 2” (50 mm) in diameter. 700V Safety Arm (#05275) sold separately 700PD #05270, #05272 WARNING! READ AND UNDERSTAND ALL INSTRUCTIONS. FAILURE TO FOLLOW ALL INSTRUCTION LISTED INSIDE MAY RESULT IN ELECTRIC SHOCK, FIRE, AND/OR SERIOUS PERSONAL INJURY. SAVE THESE INSTRUCTIONS! CSA approved for the United States and Canada 0819-58887 Optional Safety Arm #05275
Transcript
1
REED MANUFACTURING COMPANY 1425 West Eighth St. Erie, PA 16502 USA
PHONE: 800-666-3691 or 814-452-3691 Fax: 800-456-1697 or 814-455-1697
www.reedmfgco.com
700PD Power Drive• Automatethepipethreadingprocess
WARNING!READ AND UNDERSTAND ALL INSTRUCTIONS. FAILURE TO FOLLOW ALL INSTRUCTION LISTED INSIDE MAY RESULT IN ELECTRIC SHOCK, FIRE, AND/OR SERIOUS PERSONAL INJURY.
SAVE THESEINSTRUCTIONS!
CSA approved for
the United States and Canada
0819-58887
Optional Safety Arm
#05275
2
WORK AREA1. Keep your work area clean and well lit. Cluttered benches
and dark areas invite accidents.2. Do not operate power tools in explosive atmospheres,
such as in the presence of flammable liquids, gases, or dust.Powertoolscreatesparkswhichmayignitethedustorfumes.
3. Keep bystanders, children, and visitors away while operat-ing a power tool.Distractionscancauseyoutolosecontrol.
ELECTRICAL SAFETY1. Grounded tools must be plugged into an outlet properly
installed and grounded in accordance with all codes and ordinances. Never remove the grounding prong or modify the plug in any way. Do not use any adaptor plugs. Check with a qualified electrician if you are in doubt as to whether the outlet is properly grounded. Ifthetoolsshouldelectricallymalfunctionorbreakdown,groundingprovidesalowresistancepathtocarryelectricityawayfromtheuser.
2. Avoid body contact with grounded surfaces such as pipes, radiators, ranges and refrigerators. Thereisanincreasedriskofelectricshockifyourbodyisgrounded.
3. Don’t expose power tools to rain or wet conditions. Waterenteringapowertoolwillincreasetheriskofelectricshock.
4. Do not abuse the cord. Never use the cord to carry the tools or pull the plug from an outlet. Keep cord away from heat, oil, sharp edges or moving parts. Damagedcordsincreasetheriskofelectricshock.
5. When operating a power tool outside, use an outdoor extension cord marked “W-A” or “W”.Thesecordsareratedforoutdooruseandreducetheriskofelectricshock.
6. Use proper extension cords (see chart).Insufficientconduc-torsizewillcauseexcessivevoltagedrop,lossofpowerandoverheating.
7. Connect the tool to an AC power supply that matches the name plate specifications.Incorrectvoltagesupplycancauseelectricalshockorburns.
PERSONAL SAFETY1.Stay alert, watch what you are doing and use common
sense when operating a power tool. Do not use tool while tired or under the influence of drugs, alcohol, or medica-tion. Amomentofinattentionwhileoperatingpowertoolsmayresultinseriouspersonalinjury.
2. Dress properly. Do not wear loose clothing or jewelry. Contain long hair. Keep your hair, clothing and gloves away from moving parts. Looseclothes,jewelry,orlonghaircanbecaughtinmovingparts.
3. Avoid accidental starting. Be sure switch is OFF before plugging in. Carryingtoolswithafingerontheswitchorplug-gingintoolsthathavetheswitchONinvitesaccidents.
4. Remove adjusting keys or wrenches before turning on the tool. Awrenchorakeythatisleftattachedtoarotatingpartofthetoolmayresultinpersonalinjury.
5. Do not overreach. Keep proper footing and balance at all times. Properfootingandbalanceenablesbettercontrolofthetoolinunexpectedsituations.
6. Use safety equipment. Always wear eye protection. Dustmask,non-skidsafetyshoes,hardhat,orhearingprotectionmustbeusedforappropriateconditions.
TOOL USE AND CARE1. Use clamps or other practical methods to secure and sup-
port the workpiece to a stable platform. Holdingtheworkbyhandoragainstyourbodyisunstableandmayleadtolossofcontrol.
2. Do not force the tool. Use the correct tool for your applica-tion. Thecorrecttoolwilldothejobbetterandsaferattherateforwhichitisdesigned.
3. Do not use the tool if switch does not turn it ON or OFF. Anytoolthatcannotbecontrolledwiththeswitchisdangerousandmustberepaired.
4. Disconnect the plug from the power source before mak-ing any adjustments, changing accessories, or storing the tool. Suchpreventivesafetymeasuresreducetheriskofstart-ingthetoolaccidentally.
5. Store idle tools out of reach of children and other un-trained persons. Toolsaredangerousinthehandsofun-trainedusers.
6. Maintain tools with care. Keep cutting tools sharp and clean. Properlymaintainedtools,withsharpcuttingedgesarelesslikelytobindandareeasiertocontrol.
7. Check for misalignment or binding of moving parts, break-age of parts, and any other condition that may affect the tool’s operation. If damaged, have the tool serviced before using. Manyaccidentsarecausedbypoorlymaintainedtools.
8. Use only accessories that are recommended by the manu-facturer for your model. Accessoriesthatmaybesuitableforonetoolmaybecomehazardouswhenusedonanothertool.
SERVICE1. Tool service must be performed only by qualified repair
2. When servicing a tool, use only identical replacement parts. Follow instructions in the Maintenance section of
this manual. Useofunauthor-izedpartsorfailuretofollowMaintenanceInstructionsmaycreateariskofelectricshock
orinjury.
SPECIFIC SAFETY RULESTheOperator’sManualcontainsspecificsafetyinformationandinstructionsforyourprotectionagainstseriousinjuriesincluding:•Lossoffingers,hands,armsorotherbodypartsifclothingor glovesgetcaughtinmovingparts.•Electricalshockorburnsfromcontactwithwires,motororother powerdriveparts.• Impactinjuries,includingbrokenbonesifmachinetipsoveror workpiecefalls.•Eyeinjuries,includingbeingblindedbytheworkpieceor workpiecechips.
Read and follow the safety labels on the machine.Knowthelocationandfunctionsofallcontrolsbeforeusingthetool.
Reed Manufacturing700PD Power Drive
Minimum Wire Gauge for Cord Set Nameplate TOTAL LENGTH (IN FEET) Amps 0 - 25 26 - 50 51 - 100 0-6 18AWG 16AWG 16AWG 6-10 18AWG 16AWG 14AWG 10-12 16AWG 16AWG 14AWG 12-16 14AWG 12AWG NOT RECOMMENDED
Please submit tool serial number when requesting service.
3
TOOL SAFETY1. The POWER DRIVE is made to thread pipe. Follow instruc-
tions in this Operator’s Manual on tool use. Otherusesmayincreasetheriskofinjury.
2. ALWAYS secure POWER DRIVE using the 700V safety arm (#05275). Do not use this POWER DRIVE without the safety arm. Thesafetyarmresiststorquedevelopedduringthreadingandpreventslosingcontrolofthetool.
3. Do not use dull or damaged dies.Sharpcuttingtoolsarelesslikelytobindandtooliseasiertocontrol
4. Do not use if MOMENTARY CONTACT SWITCH is broken. Thepurposeoftheswitchistopreventinjuries.
OPERATIONFor threading with drophead die heads only, such as Reed R12+ Dropheads with R12+ Segmental Dies.WARNING: OPERATOR SHOULD BE THOROUGHLY FAMIL-IAR WITH SAFETY INFORMATION BEFORE ATTEMPTING TO OPERATE THIS EQUIPMENT.
WARNING: WHEN THREADING ANY SIZE PIPE, THE 700V SAFETY ARM SHOULD ALWAYS BE USED AND SECURELY LOCKED ON PIPE BECAUSE OF TORQUE DEVELOPED DURING THREADING.3.Ensureatleast6”(150mm)ofexposedpipeend.Position700Vsafetyarmbetween4”(100mm)and7”(180mm)fromtheendofthepipesotheendoftheguidebaris1”(25mm)to4”(100mm)beyondtheendofthepipe.Clampthesafetyarmsecurelyontothepipe.Whenthreading11/2”and2”pipe,itisbesttoplacethesafetyarmjust4”(100mm)fromtheendofthepipeforfirmestcontrolofhighertorque.
Motor Brush ReplacementCheckmotorbrushesevery6monthsor250workinghoursandreplacethebrusheswhenworntolessthan1/4”(5mm).Harshenvironmentalconditionscouldwarrantmorefrequentchecks.Whencheckingthebrushesforwear,alsocleanthebrushholderswithacleanrag.
WARNING: CLOTHING/GLOVES CAN BE CAUGHT IN MOVING PARTS. FINGERS, HANDS, ARMS OR OTHER BODY PARTS CAN BE CRUSHED OR BROKEN.•Donotwearloosegloves.•Keepsleevesandjacketsbuttoned.•Keepswitchinworkingorder.•Usesafetyarmwhenthreading.•Donotcarryplugged-intoolwithfingeronswitch.
REED MANUFACTURING COMPANY 1425 West Eighth St. Erie, PA 16502 USA
PHONE: 800-666-3691 or 814-452-3691 Fax: 800-456-1697 or 814-455-1697
www.reedmfgco.com 0819-58887
Reed Limited WarrantyREEDwill repair or replace toolswith any defects due to faultymaterialsorworkmanshipforone(1)yearorfive(5)yearsfromthedateofpurchase,asapplicable.Thiswarrantydoesnotcoverpartfailureduetotoolabuse,misuse,ordamagecausedwhererepairsormodificationshavebeenmadeorattemptedbynonREEDauthorizedrepair technicians.Thiswarranty applies only toREED tools anddoesnotapplytoaccessories.Thiswarrantyappliesexclusivelytotheoriginalpurchaser.
One (1) year warranty: Powerunitsforpneumatic,electric,hydraulicandbattery-poweredtoolshaveaoneyearwarranty.Thisincludes,butisnotlimitedtoREEDpumps,universalpipecuttermotors,powerdrives, power bevel tools, threadingmachines, cordlessbatteriesandchargers.
Five (5) year warranty: AnyREEDtoolnotspecifiedundertheone(1)yearwarrantyaboveiswarrantiedundertheREEDfive(5)yearwarranty.
