7/1
3
2:: Introduction
:: KIT Features
:: Additional Features
:: Other Helpful Items
Associated Electrics, Inc.26021 Commercentre Dr.Lake Forest, CA 92630
http://www.TeamAssociated.com · http://www.RC10.com · http://twitter.com/Team_Associated · http://bit.ly/AEonFacebook
Customer ServiceTel: 949.544.7500Fax: 949.544.7501
Thank you for purchasing this Team Associated product. This assembly manual contains instructions and tips for building and maintaining your new RC10TC6.1. Please take a moment to read through this manual to help familiarize yourself with these steps.
We are continually changing and improving our designs; therefore, actual parts may appear slightly different than in the illustrations. New parts will be noted on supplementary sheets located in the appropriate parts bags. Check each bag for these sheets before you start to build.
Team Associated is proud to release its next generation 1:10th scale 4WD electric touring car kit, the RC10TC6.1-FT, with optimized suspension geometry equipped to carry the load for today’s touring car racing classes.
The engineers behind the doors of Area-51 have been hard at work continuing the development process for the ever changing touring car racing scene. The RC10TC6.1-FT is the next stepping stone in Team Associated’s successful touring car chassis lineage. Holding cross-compatibility to a high regard, the RC10TC6.1-FT shares the same chassis layout as its predecessor, the TC6. But this time the advances are in its suspension geometry and drivetrain components.
Building from a balanced and stable chassis layout, the time was right to refine the suspension components. The updated suspension geometry of the RC10TC6.1-FT has been re-worked for increased stiffness and durability with finer adjustments focused in the optimal range. All without sacrificing low part count or affordability. With the demands of the extreme power of modified brushless motors, the RC10TC6.1-FT also benefits from the addition of a tunable oil-filled gear differential in the rear, and fixed spool with replaceable outdrive cups for the front. Area-51’s design engineers have packaged all the key components together, so the RC10TC6.1-FT is definitely… another Champion by Design from Team Associated!
• Updated suspension arms o Stiffer/stronger design o Finer adjustments for shock mounting with “in between” options o Optimized arm length front & rear• Hubs & caster blocks use inserts for adjustable caster/toe angles o Caster blocks have a stiffer/stronger design with 2, 4, and 6 degree insert options for caster angle o Rear hubs use a stronger design with 0 and 1 degree insert options for outboard toe angle• Updated anti-roll bar system allows finer adjustments with precision mounting• Rear gear diff for maximum performance and minimal maintenance o Lightweight design o Durable composite construction o Optimized for a wide “tuning window” to maximize useable adjustability o Hard anodized aluminum outdrives for low wear and long life• Front spool with replaceable composite outdrives o Outdrives allow the use of existing CVA bone blades to minimize binding at the bearing surface o Composite outdrives are replaceable at low cost in the event of a CVA bone blade failure• Offset arm mounts included to help increase durability by minimizing (or eliminating) shims between mount and bulkhead• Chassis layout optimized for Lithium Batteries and Brushless Motors o Ultra narrow LiPo chassis with two battery positions o Servo mounting slots to ensure proper fit of any servo o Motor mounts to centralized point in chassis for equal flex• Common bulkhead layout minimizes spare part cost• Multi-position steering system to fine tune Ackermann and steering rates o More Ackermann options (14 positions total) to fine tune steering point o Improved steering input rate for more consistent handling, with 3 output rate options• V2 Shock with hard anodized threaded shock bodies o Bottom loading seal system for ease of build o TiN coated shock shaft o Piston attaches to shock shaft with screw for tight clamping and no slop o Threaded collar with fine pitch thread for ease of accurate ride height adjustment• Titanium turnbuckles with new turnbuckle eyelets for easy access to ball stud• 16 precision ball bearings
• Cross-compatibility with TC6 chassis components
Your new TC6.1 comes unassembled and requires the following items for completion. (refer to catalog section for suggestions):
• 1:10th scale electric motor and electronic speed control • 3.7V-7.4V LiPo, 6.6V LiFe, or 4.8V-7.2V NiMh/NiCd• Battery charger (suited for, and particular to, one of the batteries mentioned above)• 2 channel surface transmitter, 2 channel receiver, and steering servo• 1:10th scale lexan touring car body and Lexan specific paint for body • 1:10th scale rubber (or foam) touring car tires
• Silicone Shock Fluid (Refer to catalog for complete listings) • Silicone Diff Fluid (Refer to catalog for complete listings) • Thread Lock (AE Part #1596) • Body Scissors (AE Part # 1737) • Reamer / Hole Punch • FT Hex Wrenches (AE Part # 1541) • Hobby Knife • Needle Nose Pliers • Wire Cutters • Soldering Iron • Calipers or a Precision Ruler
3:: Table of Contents
:: Notes
This symbols indicates a special note or instruction in the manual.
!There is a 1:1 hardware foldout page in the back of the manual. To check the size of a part, line up your hardare with the correct drawing until you find the exact size. Each part in the foldout has a number assigned to it for ordering replacement parts.
1...................Cover
2...................Introduction 3...................Table of Contents
4-5...............Shock Build (Bag A-AA)
5-6..............Front Spool Build (Bag B-BB)
6-8..............Rear Gear Differential Build (Bag B-BB)
8-9..............CVA Axle Build (Bag C-CC)
9..................Turnbuckle Build (Bag C-CC)
10...............Front Bulkhead Build (Bag D-DD)
11................Rear Bulkhead Build (Bag D-DD)
12...............Spur Gear Bulkhead / Motor Mount Install (Bag D-DD)
12...............Shock Tower Build (Bag D-DD)
13...............Steering Bellcrank Build /Install (Bag E)
14...............Spur Gear Shaft Build (Bag F)
14-15........Spur Gear Hub / Belt Install (Bag G-GG)
15...............Front Spool Install (Bag F)
15...............Rear Gear Differential Install (Bag F)
15-16.........Top Plate / Bearing Caps Install (Bag F)
16-18..........Steering Block Build / Install (Bag G)
19-20.........Rear Hubs Build / Install (Bag G)
20................Shocks Install (Bag G)
20-21.........Bumper Build / Install (Bag G)
21.................Pivoting Body Mounts Install (Bag H)
21-22.........Battery Braces / Antenna Mount Install (Bag H)
22-23.........Anti-Roll Bars Build / Install (Bag I-II)
23-24.........Servo Build / Install (Bag J)
24-25.........Electronics Install (Bag J)
25................Wheels / Tires Build / Install (Bag J)
26-28.........Tuning Tips
29................Gear Chart
30-38.........Catalog
38................Notes
39................Setup Sheet “Kit Setup”
40................1:1 Hardware “Fold Out”
41.................Setup Sheet “Blank”
42................Back Cover
Associated Electrics, Inc.26021 Commercentre Dr.Lake Forest, CA 92630
http://www.TeamAssociated.com · http://www.RC10.com · http://twitter.com/Team_Associated · http://bit.ly/AEonFacebook
Customer ServiceTel: 949.544.7500Fax: 949.544.7501
4:: Shock Build - Bag A-AA - Step 1
:: Shock Build - Bag A-AA - Step 2
:: Shock Build - Bag A-AA - Step - 3
Bladder Installation
With the shaft fully extended, place bladder on the top of the shock body, displacing the extra oil. While maintaining pressure on the bladder against the shock body, carefully lift one side of the bladder to allow any extra oil to escape. Place stock cap on top of bladder, and secure it by threading the aluminum cap retainer onto the shock body.
31325VCS3 shock
body
6465Shockpiston(#2)
31330VCS3 shock
shaft
31305Turnbuckle
eyelet
5407Red
o-rings
31324VCS3o-ringspacer
31324Shock
bladder
31329VCS3 shock
cap
31326VCS3 shock
collar o-ring
31326VCS3
shock collar
31327VCS3 shockbottom cap
31327VCS3 shock bottom cap
o-ring
31510M2x4mm
bhcs
31324Hat
bushing
31328VCS3
Aluminum cap retainer
31324VCS3 piston
bushing
Shock oil#5423(40wt)
Shock oil
#5423(40wt)
Shock oil#5423(40wt)
#1596thread lock
5:: Shock Build - Bag A-AA - Step 4
:: Front Spool Build - Bag B-BB - Step 1
:: Front Spool Build - Bag B-BB - Step 2
31339Diff pulley
flange
31339Diff pulley
(40T)
31342Spool hub
3942Silver spring14.5lb(front)
3942Silver spring14.5lb(rear)
6475Shock
spring cup
Build four shocks
!Build four
spring cup
#1597
ca glue
Cam Position
Mid-Low Mid-High
Low High
Note!Always use the same cam position on both sides of the spool.
Belt TensionNumber
View from left side of car
17 32
161
Right Side
Left Side
31185Diff
bearing cam
31510M2x4mm
bhcs
31184Cam
holder(mid-low)
x2
x4
x2
#1596thread lock
Use belt tension position 8 for
standard setup.
!
6:: Front Spool Build - Bag B-BB - Step 3
:: Rear Gear Differential Build - Bag B-BB - Step 1
:: Rear Gear Differential Build - Bag B-BB - Step 2
x2
x4
x2
x2
31162Shim
31350M2.5x10mm
fhcsx2
x4
3140110x15mmbearing
31348TC6 gear diff shim
31341TC6 spool outdrive
x2
Build twooutdrives
!
31346TC6 gear
diff outdrive
31349TC6 gear diff seals
31349TC6 gear diff seals
31345TC6 gear diff sun
gear
31345TC6 gear
diff planet gear
31347TC6 gear diff case
31348TC6 gear diff shim
31348TC6 gear diff pin
31348TC6 gear diff shim
31348TC6 gear diff pin
#65
88bl
ack
grea
se
#6588
black grea
se
#1596
thre
ad lo
ck
7:: Rear Gear Differential Build - Bag B-BB - Step 3
:: Rear Gear Differential Build - Bag B-BB - Step 4
:: Rear Gear Differential Build - Bag B-BB - Step 5
x231162Shim
x23140110x15mmbearing
Fill to top of cross pins
!
31349TC6 gear diff seals
31345TC6 gear diff sun
gear31347
TC6 gear diff pulley
31348TC6 gear diff pin
31348TC6 gear diff shim
4675M2.5x6mm
fhcs
31347TC6 gear
diff gasket
x2
#6588
black grea
se
Shock oil#5423(40wt)
8:: Rear Gear Differential Build - Bag B-BB - Step 6
:: Rear Gear Differential Build - Bag B-BB - Step 7
:: CVA Axle Build - Bag C-CC - Step 1
31367TC6.1 CVA
coupler31367
CVAcross pin
31368TC6.1 CVA
bones31369
TC6.1 CVA axle
#6588
black grease
Use belt tension position 7 for
standard setup.
!
Cam Position
Mid-Low Mid-High
Low High
Note!Always use the same cam position on both sides of the vehicle.
Belt TensionNumber
View from left side of car
17 32
161
Right Side
Left Side
31185Diff
bearing cam
31184Cam
holder(mid-low)
x2 x2
9:: CVA Axle Build - Bag C-CC - Step 2
:: CVA Axle Build - Bag C-CC - Step 3
:: Turnbuckle Build - Bag C-CC - Step 1Servo Turnbuckle
Steering Turnbuckle
Camber Turnbuckle
29.55mm
14180.825”
turnbuckle
14021.375”
turnbuckle
14051.875”
turnbuckle
46.35mm
57mm
x2
45mm
x2 x2
31305Turnbuckle
eyelet
Front Rear
31238CVA blade
31237retaining
clip
31500M3x2.5mm
setscrew
Build four CVA’s
Note!Align the gap in
the pin retainer to be opposite of the
CVA pin.
!
! #1596
thre
ad lo
ck
10:: Front Bulkhead Build - Bag D-DD - Step 1
:: Front Bulkhead Build - Bag D-DD - Step 2
:: Front Bulkhead Build - Bag D-DD - Step 3
x4
x2
89202M3x12mm
bhcs
31309TC6
bulkhead
31540M3x5mm
fhcs
31300TC6
chassis
x4
Refer to page 27for droop settings!
!
Build left and right
sides
!
Build left and right
sides
Build left and right
sides
!
!
Build left and right
sides
!
Wheel Base Shims
1mm 2mm
x2
x2
312805mm
ballstud(short)
31221Inner
hinge pin
31200Wheelbase shim (2mm)
31200Wheelbase shim (1mm)
25227M4x8mmsetscrew
31356Front
suspensionarm
31356Front
suspensionarm insert
(b)
x2
x2
x2
x431322TC6 armmount
bushing
x431361TC6.1 arm
mount(0 offset)
Arm Mounts
Roll CenterLow High
Std Offset0 1 2 3
Suspension Arm Insert
(front)
A
A
B
B
C
C
11:: Rear Bulkhead Build - Bag D-DD - Step 1
:: Rear Bulkhead Build - Bag D-DD - Step 2
:: Rear Bulkhead Build - Bag D-DD - Step 3
1º 1.5º 2º
Arm Mount Shims x4
x2
89202M3x12mm
bhcs
31309TC6
bulkhead
31540M3x5mm
fhcs
x4
Refer to page 27for droop settings!
!
31540M3x5mm
fhcs
Wheel Base Shims
1mm 2mm
x231361TC6.1 arm
mount(0 offset)
31200Wheelbase shim (2mm)
x2
x2
31200Wheelbase shim (1mm)
x231322TC6 armmount
bushing
x231221Inner
hinge pin
25227M4x8mmsetscrew
x2
x2312805mm
ballstud(short)
31357Rear
suspensionarm
31357Rear
suspensionarm insert
(b)
Rearsuspension
arm
Arm Mounts
Roll CenterLow High
Std Offset0 1 2 3
x231321TC6 arm mount(0 dot)
x231322TC6 armmount
bushing
C B A
AB
C
Suspension Arm Insert
(rear)
12:: Spur Gear Bulkhead/Motor Mount Install - Bag D-DD - Step 1
:: Shock Tower Build - Bag D-DD - Step 1
:: Shock Tower Build - Bag D-DD - Step 2
Do not tighten #31541 screws all the way! Leave screws
loose until bearing caps are attached to bulkheads!
!
x2
x2
x2
x4x2
2230Body
mounts
31531M3x6mm
bhcs
312818mm
ballstud(short)
31541M3x6mm
fhcs
31532M3x8mm
bhcs
31303TC6 shock
tower (rear)
31550M3
locknut
x231250Shock
bushing
x231310TC6
bearing cap
Do not tighten #31541 screws all the way! Leave screws
loose until bearing caps are attached to bulkheads!
!
!
!
31312TC6 motor
mount
31313TC6 motor
mount brace
31540M3x5mm
fhcs
31311TC6
spur gear bulkhead
31532M3x8mm
bhcs
31540M3x5mm
fhcs
31531M3x6mm
bhcsx4
x2
x2
x231310TC6
bearing cap
31302TC6 shock
tower (front)
31531M3x6mm
bhcs
312818mm
ballstud(short)
31550M3
locknut
31541M3x6mm
fhcs
31250Shock
bushing
x2
x2
x2
x4 1
1
1
2
2
2
3
3
3
4
4
4
5
5
5
6
6
6
x2
1234567
13:: Steering Bellcrank Build / Install - Bag E - Step 1
:: Steering Bellcrank Build / Install - Bag E - Step 2
:: Steering Bellcrank Build / Install - Bag E - Step 3
31308TC6 steering
bellcrankpost insert
Use rear hole for standard position!
Refer to page 26 for Ackermann chart
!
0.5mm
Servo Saver Adjustment
314034x7mmbearing
31307TC6 steering
post
31306TC6 steering
bellcrank tube
312805mm
ballstud(short)
31308TC6 servo saver arm
31306TC6 servo
saver spring
31306TC6 servo saver nut
x2
31307C-clip
Steering Bellcrank
7
8
A B C
Align steering bellcrank to position B for initial set-
ting. Refer to page 26 for Ackermann chart.
!7
31532M3x8mm
bhcs
312805mm
ballstud(short)
31308TC6 bellcrank arm (7mm)
31308TC6 bellcrank
x2
14:: Spur Gear Shaft Build - Bag F - Step 1
:: Spur Gear Shaft Build - Bag F - Step 2
:: Spur Gear Hub / Belts Install - Bag F - Step 1
Front Belt
Rear Belt
31187Front belt
31188Rear belt
31333TC6
spur gear (87T / 48P)
31530M3x5mm
bhcs
31320TC6 spurpulley (20T)
31314TC6 spur gear hub
31319TC6 spur gear clamping ring
x3x2
#1596
thread lock
31315TC6 spur
gear shaft
x2
x2
313314x8x3
flanged bearing
31162Shim
311603mm E-clip
311603mm E-clip
15:: Spur Gear Hub / Belts Install - Bag F - Step 2
:: Front Spool / Rear Gear Differential Install - Bag F - Step 1
:: Top Plate / Bearing Caps Install - Bag F - Step 1
x8
x3
31540M3x5mm
fhcs
31530M3x5mm
bhcs
31301TC6 top plate
Note!Place top
plate between the front belt.
!
Slide belt over gear diff pulley!
!Slide belt over spool pulley!
!Slide belt over spool pulley!
!
x231521M2.5x8mm
bhcs
#1596
thread lock
16:: Top Plate / Bearing Caps Install - Bag F - Step 2
:: Steering Block Build / Install - Bag G - Step 1
:: Steering Block Build / Install - Bag G - Step 2
Note side view
RACERS TIP:Use small amount ca glue to
permanently secure the caster block inserts in the caster
blocks.
Use the supplied symmetric inserts to select caster angle. The number should
be on top for left and right caster blocks
as shown.
!
!!
!
!
252375x10mmbearing
x2
312805mm
ballstud(short)
31370TC6.1
axle crush tube
31360TC6.1
steering blocks
31358TC6.1 caster
blocks(left and right)
31358TC6.1 caster
block inserts(4 deg)
x24 4
x4 x431531M3x6mm
bhcs
31531M3x6mm
bhcs
Tighten #31531 screws.Then tighten #31541
shock tower screws from page 12!
!
RightLeft
17:: Steering Block Build / Install - Bag G - Step 3
:: Steering Block Build / Install - Bag G - Step 4
:: Steering Block Build / Install - Bag G - Step 5
31532M3x8mm
bhcs
312848mm
ballstud(long)
31162Axle shim
31214Caster block
bushing
x2
311121/16” x 5/16”
dowel pins
18:: Steering Block Build / Install - Bag G - Step 6
:: Steering Block Build / Install - Bag G - Step 7
:: Steering Block Build / Install - Bag G - Step 8
It is important that the turnbuckle eyelets move freely once snapped on to the ballstud. If the fit is too tight, the car handling will be inconsistent. To check, grab turnbuckle eyelet with fingers and rotate the cup. If
there is resistance, lightly squeeze ball cup with needle nose pliers as shown and test again. It is important
that the ball cup be snapped onto the ballstud before squeezing with needle nose pliers. Be sure to check and adjust the fit for each ball cup that is installed.
!
31234Clamping wheel hex
x2
31511M2x5mm
shcs
x2x231222
Outerhinge pin x231510
M2x4mmbhcs
Build left and right
sides
!
!Orient the notch
to the left throughout the car. The notch indicates
which end has the left hand threads!
19:: Rear Hubs Build / Install - Bag G - Step 1
:: Rear Hubs Build / Install - Bag G - Step 2
:: Rear Hubs Build / Install - Bag G - Step 3
31162Axle shim
31359TC6.1
rear hub carrier
31359TC6.1
rear hub carrier inserts(0 deg)
31234Clamping whee hex
31511M2x5mm
shcs
311121/16” x 5/16”
dowel pins
x2
x2
x2
x2
x2
252375x10mmbearing
31286Aluminum ballstud washer(2mm)
x2
31370TC6.1
axle crush tube
312848mm
ballstud(long)
Clamping wheel hex
Build left and right
sides
!
RACERS TIP:Use small amount of ca
glue to permanently secure the rear hub inserts in the
hubs.
Use the supplied symmetric inserts to select rear hub toe angle. The number
should be on the outside of the hub for
left and right hubs as shown.
!!
0 0
RightLeft!
!
20:: Rear Hubs Build / Install - Bag G - Step 4
:: Shocks Install - Bag G - Step 1
:: Bumper Build / Install - Bag H - Step 1
x2
x2
31222Outer
hinge pin
31510M2x4mm
bhcs
x2 x231530M3x5mm
bhcs
31530M3x5mm
bhcs
Transpondernot included!
2230Body
mounts
31316TC6 bumper
brace
31316TC6
bumper
4673M2.5x4mm
bhcs
x2
x3
x2x3
25202M3x10mm
fhcs
25203M3x12mm
fhcs
31317TC6 foam bumper
!
!Orient the notch
to the left throughout the car. The notch indicates
which end has the left hand threads!
Refer to page 18 for
turnbuckle install tips
!
21:: Bumper Build / Install - Bag H - Step 2
:: Pivoting Body Mounts Install - Bag H - Step 1
:: Battery Braces / Antenna Mount Install - Bag H - Step 1
25201M3x8mm
fhcs
x2
x231530M3x5mm
bhcs
3897Pivoting
body mounts 1736FT body
clips, blue(short)
x2
x2x2
x2
3897Pivoting
body mounts
1736FT body
clips, blue(short)
31530M3x5mm
bhcs
31318TC6 lipo battery
brace (fr/rr)
31540M3x5mm
fhcs
31318TC6 inner lipo brace
x2
x2x2
x231304TC6 battery
tape tab
Sand the inside edges of the TC6 battery tape tabs
!
!
!
22:: Battery Braces / Antenna Mount Install - Bag H - Step 2
:: Anti-Roll Bars Build / Install - Bag I-II - Step 1
:: Anti-Roll Bars Build / Install - Bag I-II - Step 2
8828Anti roll bar cups
31269Anti roll bar pivot
mount
31058Anti roll
bar ballstud
x231511M2x5mm
shcs
Build four anti-roll
bar mounts Install four anti-roll bar
mounts, two for the front arms and two for the
rear arms.
!!
16.5mm
Anti Roll Bar Link Adjustment
16.5mm
31540M3x5mm
fhcs
31540M3x5mm
fhcs
31318Antenna mount
x4
Use forward position for standard setup. Refer to page 26 for explanation of battery
position tuning options!
!
Front 31362Anti roll bar pivot
313641.1mm roll bar(yellow)
31363TC6.1 anti
roll bar tube
x4
x2
31500M3x2.5mmset screw
Shrink the colored heat shrink tubing to
the anti roll bar!
!
Anti Roll Bar Color/Size Chart
GreenWhiteBlue
YellowRed
0.8mm0.9mm1.0mm1.1mm1.2mm
23:: Anti-Roll Bars Build / Install - Bag I-II - Step 3
:: Anti-Roll Bars Build / Install - Bag I-II - Step 4
:: Servo Build / Install - Bag J - Step 1
Rear
31511M2x5mm
shcs
31511M2x5mm
shcs
x2
x2
x2
x2
31365Anti roll
bar mounts
31365Anti roll
bar mounts
31362Anti roll bar pivot
313640.9mm roll bar(white)
x4
x2
31500M3x2.5mmset screw
312805mm
ballstud(short)
89007Servo
horn ring9180Servo horn
31286Aluminum
ballstud washer(1mm)
x2
x2x4
x4 7336Servo spacer
31246Servo
mounts31532
M3x8mmbhcs
7337.250x.125x.015
washer
Shrink the colored heat shrink tubing to
the anti roll bar!
!31363
TC6.1 anti roll bar
tube
!Use screw that was included
with your servo.Servo not included!
Anti Roll Bar Color/Size Chart
GreenWhiteBlue
YellowRed
0.8mm0.9mm1.0mm1.1mm1.2mm
24:: Servo Build / Install - Bag J - Step 2
:: Electronics Install - Bag J - Step 1
:: Electronics Install - Bag J - Step 2
Steering Servo ChartAssociated
* Not all servo’s are listed* Make sure servo linkage clears the servo through full travel in both directions. Use #7336 servo spacers to adjust servos position as necessary.
XP-1015, XP-1313 F
F
F
F
A
A
H
H
J
J
J
# 9180servo arm
94102
HS-5625MG, HS-5645MG, HS625MG, HS645MG
Z4725, Z4750, Z2750, Z8450, Z8550, NES-4750
Z250, Z550
S9204, S9250, S9450, S148
S3003, S9202, S9101
S9404
94738, 94157, 94158, 94257, 94258, 94357, 94358, 94452, 94453, 94751, 94755
HS-322HD, HS-325HB, HS-965, HS-985MG, HS-5965, HS-5985MG, HS-425BB, HS-422
PS-401, PS-2001, PS-2004, PS-2015, PS-2173, PS-2174, PS-2123, PS-2143, PS-2144
Airtronics
Airtronics
Hitec
Hitec
JR
JR
Futaba
Futaba
Futaba
KO
31540M3x5mm
fhcs
x2
ESC not included!
Receiver not included!
6338Antenn tube
31500M3x2.5setscrew
Gearing will depend on themotor and track size.
Motor, pinion gear, and set
screw are not included!
x2
x2
31286Aluminum ballstudwasher(1mm)
31531M3x6mm
bhcs
!
!
!
25:: Electronics Install - Bag J - Step 3
:: Electronics Install - Bag J - Step 4
:: Wheel & Tire Build / Install - Bag J - Step 1
Battery not included!
Use strapping tape to secure battery into chassis.Wrap the tape around the #31304 battery tape tab
and back onto itself. Battery tape not included!
91148M4
locknut
x4
Wheels, tires, and inserts not included!
!
!
!
:: Tuning TipsTips for Beginners:
Before making any changes to the standard setup, make sure you can get around the track without crashing. Changes to your car will not be beneficial if you can’t stay on the track. Your goal is consistent laps.
Once you can get around the track consistently, start tuning your car. Make only ONE adjustment at a time, testing it before making another change. If the result of your adjustment is a faster lap, mark the change on the included setup sheet (make additional copies of the sheet before writing on it). If your adjustment results in a slower lap, revert back to the previous setup and try another change.
When you are satisfied with your car, fill in the setup sheet thoroughly and file it away. Use this as a guide for future track days or conditions.
Ride Height:
The standard starting point for ride height is 5.0mm (keep in mind that your local track may have minimum ride height requirements). You can slightly raise the rear relative to the front to give the car more steering. Raise the car slightly for tracks with large bumps.
Battery Placement:
For most cases, run the battery in the standard forward position. Typically this will be the most stable and easiest to drive. Try moving the battery back if you encounter a low traction surface.
Ackermann & Steering Rate:
Ackermann refers to the relative angle difference between the front wheels as they are turned to steer the car. The outside wheel will turn less than the inside wheel in most conditions. Settings with more Ackermann will have a bigger difference in wheel angle, causing the outside wheel to turn less. Likewise, settings with less Ackermann will cause the outside wheel to turn more.
Increasing the Ackermann will smooth out the steering and is used most often on high traction surfaces such as carpet. This is a result of the reduced outside wheel angle. Settings with reduced Ackermann will help to increase corner entry steering, and are typically used when running a spool in the front.
The steering rate is also adjusted when changing the length of the steering bellcrank. There are three rate options. The shortest position (position C) produces a slower speed than the longest position (position A). Slower steering rates will make the car less aggressive, making it easier to drive. These settings are good for high traction conditions such as carpet.
The chart to the right lists the different Ackermann options along with their associated steering rates.
SteeringBellcrank
SteeringLink
SteeringSpeed
Fast
Fast
Slow
Slow
Slow
Fast
Medium
Medium
Medium
Fast2B7A
2B8A
1B7C
2B8B
2A7A
1A7C
2A7B
2A8B
1B8C
2B7B STD
2A8A
1A8C
Medium
Slow
More
Ack
erm
ann
Less
Ack
erm
ann
Wheelbase:
Lengthening the front will reduce steering, shortening the front will increase steering. Shortening the rear will increase rear grip, lengthening the rear will decrease rear traction.
Wheel Base Shims
1mm 2mm
Rear Toe-In:
Decreasing toe-in will decrease rear traction and increase corner speed. Use numbered toe shims for adjustment.1º 1.5º 2º
Arm Mount Shims
Steering Bellcrank
7
8
A B C
AB
2
1
Steering Link
26
:: Tuning Tips
Camber Link Position:The camber link is used to set static camber at ride height, but it is also an effective setting to adjust roll center height and camber gain. The TC6.1 has 7 positions for the front camber link, and 14 for the rear. These positions vary in both length and angle.
Longer links will produce less camber gain, stiffening that particular end of the car in roll. These are particularly effective on large tracks with big sweeping corners. Shorter links will give more camber gain, softening that end of the car in roll. This will make the car more aggressive, and is a good setting for smaller indoor tracks with high grip levels.
The angle of the camber link will make fine adjustments to the roll center height. Typically the camber link will be no more than parallel to the suspension arm with the inboard side of the link lower than the outboard side. As the inboard side of the camber link is moved down, the roll center goes up, stiffening that end of the car. Camber link angle is a good adjustment to help fine tune the balance of the car to the track by setting the front and rear at slightly different angles.
Caster:Caster describes the angle of the kingpin from vertical while looking from the side of the car. Positive caster means the top of the kingpin leans rearward. Negative caster means the kingpin is leaning towards the front of the car. Since caster is measured at the wheel, it is affected by running any inclination in your inboard arm mount. Kick-up adds (+) caster, and anti-dive adds (-) caster.
When figuring out your caster at the wheel, add the number of degrees of kick-up or anti-dive and add it to the degree caster blocks you have on the car.
Typically for most racing surfaces, 4 degrees caster is the normal starting point for the Team. From there, increase caster to reduce mid to exit steering and make the front end less responsive. Conversely, decreased caster gives a more responsive feel and more exit steering.
Arm Mount Position:The TC6.1’s arm mounting system allows for maximum adjustability for all track and racing conditions. Six arm mount positions allow you to run the pins flat, or with angle to produce kick-up, anti-dive, anti-squat, and pro-squat. The arm mounts are indicated zero, one, two, and three, with the corresponding number of dots on the outer face. Zero is the lower roll center and three the higher roll center, with one and two in order between.
The TC6.1 adds offset arm mounts that move the inner hinge pin out from centerline by 2mm. These help to minimize (or eliminate) the use of shims behind the arm mount, and will help to add strength and rigidity to the suspension system. The typical racing setup will use offset arm mounts for both the forward and rearward positions on the front arm. With the rear arm mounted using standard arm mounts for the forward position, and offset arm mounts for the rearward positions (producing 2.5 degrees of rear toe-in) .
Each bulkhead has two positions to attach the arm mount to. The lower position (A) is used for the lowest roll center options, and the upper position (B) is used for the highest roll center options.
In general, lower roll centers will effectively make the car softer in roll, allowing the car to lean more in the corners. Lower roll center positions are good for low traction conditions. If the grip level is high, then raising the roll centers to a higher position will help to stiffen the car in roll making it more stable.
The following chart shows some examples of arm mounting positions along with their resulting arm angles shown in degrees.
FwdMount
1˚ Kick Up
1˚ Kick Up
1˚ Kick Up
2˚ Kick Up
Flat
Flat
2˚ Kick Up
2˚ Kick Up
1˚ Anti Dive
1˚ Anti Dive
1˚ Anti Dive
2˚ Anti Dive
2˚ Anti Dive
2˚ Anti Dive
Flat
2B
2B
1B
1B
1B
2A
2A
1B
0B
0B
0B
0B
0B
0B
0B
0B
0B
0B
3A
3A
3A
2A
3A
3A
3A
1B
1B
1B
2B
3A
RwdMount Result
Front
RollCenter
High
Std.
Low
FwdMount
1˚ Anti-Squat
1˚ Anti-Squat
1˚ Anti-Squat
2˚ Anti-Squat
Flat
Flat
2˚ Anti-Squat
2˚ Anti-Squat
1˚ Pro-Squat
1˚ Pro-Squat
1˚ Pro-Squat
2˚ Pro-Squat
2˚ Pro-Squat
2˚ Pro-Squat
Flat
2B
2B
1B
1B
1B
2A
2A
1B
0B
0B
0B
0B
0B
0B
0B
0B
0B
0B
3A
3A
3A
2A
3A
3A
3A
1B
1B
1B
2B
3A
RwdMount Result
Rea
r
RollCenter
High
Std.
Low
27
Arm Mounts
Roll CenterLow High
Std Offset0 1 2 3
Droop:The standard settings of 6mm front and 5mm rear will work best in most cases. Droop is measured just underneath the outer hinge pin as shown in the photos to the right.
On bumpy or low grip surfaces, increase the droop (going to a lower number on the droop gauge), this will help increase traction and consistency.
Droop adjustments of 0.5mm to 1mm can be very effective on the track!
1 02345678
FrontDroop Setting:
6mm
10 2 3 4 5 6 7 8
RearDroop Setting:
5mm
28:: Tuning Tips
Front
Height
High
Mid-High
Mid
Low
Pos.
31
28
8
5R
ear
Height
High
Mid-High
Mid
Low
Pos.
18
20
7
9
Belt Tension:
When altering the differential height, you will need to adjust the tension of the belt. The following chart shows suggested starting positions.
Anti-Roll Bar:
Anti-roll bars are only effective during roll (when the chassis leans from side to side when cornering). Because of this they isolate a change in the suspensions spring rate in the corners only, and can be a very useful tuning option.
Anti-roll bars stiffen the spring rate of the suspension during roll movements when cornering. The larger the roll bar wire, the stiffer the spring rate will be in roll. The chart on the right shows the available anti-roll bar sizes (as well as their corresponding colors) from the softest on the top, to the stiffest on the bottom.
The standard setup, using yellow front anti-roll bars (1.1mm) and white rear anti-roll bars (0.9mm), is a balanced starting point. Changing the size of the front or rear anti-roll bars can help to make the chassis more consistent through the corner. Decreasing the size of the front anti-roll bars will help to increase mid-corner steering, but will tend to be less stable in sweepers. This is a typical setup for smaller tracks with tighter turns. Increasing the size of the front anti-roll bars will give more stability in the sweepers, and is better for larger tracks with high speed corners. Increasing the size of the rear ant-roll bars will help add stability into through the corner in high traction conditions, but can make the car inconsistent in low traction, or bumpy, surfaces.
Note! Charts show left side cam positions from the left side of the car. Match right side cam position to left side cam position.
Left SideFront
Left SideFront
Left Side
TighterLooser
Left Side
Tighter Looser
Motor Gearing:
The gear charts on the following page show final drive ratio numbers for the TC6.1. Refer to motor manufacturer’s suggested gear ratio for starting point. You may need to adjust the gearing according to your track size.
The following formula’s can also be helpful in determining final drive ratios and pinion size.
TC6 Internal Ratio = 2.0
Final Drive Ratio = (# of Teeth Spur) x (Internal Ratio) # of Teeth on Pinion
# of Teeth on Pinion = (# of Teeth on Spur) x (Internal Ratio) Final Drive Ratio
Anti-Dive (front):Anti-dive is a front arm angle where the rear mount is higher than the front mount. Adding anti-dive reduces weight transfer to the front on deceleration entering corners. It also reduces caster at the wheel.
Pro-Squat (rear):Pro-squat is a rear arm angle where the rear mount is higher than the front mount. Running Pro-Squat will increase rearward weight transfer on power.
Anti-Squat (rear):Anti-Squat describes a rear arm angle where the front mount is higher than the rear mount. Increasing anti-squat will make the rear suspension stiffer. It tends to give the car more entry steering and reduce rearward weight transfer on power.
Kick-Up (front):Kick-up describes the angle of the front suspension arm, where the front mount is higher than the rear mount. Increasing kick-up will give more entry steering, as well as increasing caster at the wheel.
Cam Position
Mid-Low Mid-High
Low High
Belt TensionNumber
View from left side of car
17 32
161
Anti Roll Bar Color/Size Chart
GreenWhiteBlue
YellowRed
0.8mm0.9mm1.0mm1.1mm1.2mm
29:: Gear Chart 48 Pitch
:: Gear Chart 64 Pitch
Blank spaces in the gear charts designates a gear
ratio that will not fit in the vehicle. Gear fitment will also depend on the motor
brand.
!
30:: Shocks
:: Springs
:: CVA’s
:: Anti-Roll Bars
:: Shock Fluid :: Turnbuckles
54076465647531305313233132431325313263132731328313293133031510
8121
14112222426
Pr.Pr.Pr.Pr.Pr.Pr.Pr.Pr.Pr.1
3941394239433944394539463952395339543988
14021405141831305
Pr.Pr.Pr.14
31366313673136831369312373123831500
11
Pr.Pr.286
Red O-RingsShock Piston, PTFEPreload Spacers, Collars, CupsTurnbuckle EyeletVCS3 Shock KitVCS3 Shock RebuildVCS3 Shock BodyVCS3 Shock CollarVCS3 Shock Bottom CapVCS3 Aluminum Cap RetainerVCS3 Shock CapVCS3 Shock ShaftM2x4mm BHCS
TC Spring, Green, 12.0lbs (Kit)TC Spring, Silver, 14.5lbs (Kit)TC Spring, Blue, 17.0lbsTC Spring, Gold, 19.5lbsTC Spring, Red, 22.0lbsTC Spring, Copper, 25.0lbsTC Spring, Purple, 30.0lbsTC Spring, Yellow, 35.0lbsTC Spring, White, 40.0lbsTC Spring Set, 1 pr. each
FT Blue Titanium Turnbuckles 1.375”FT Blue Titanium Turnbuckle 1.875”FT Blue Titanium Turnbuckle 0.825”Turnbuckle Eyelet
TC6.1 CVA KitTC6.1 CVA Rebuild KitTC6.1 CVA BoneTC6.1 Stub AxleCVA Pin Retaining ClipCVA Bone BladeM3x2.5mm Set Screw
TC Spring Set, 1 pr. each
31510
1418
1405
1402
31305 31305
31305 31305
31305 31305
31500
31238
31366 31237
3136831369
31227
6465
31324
31330
882831058313623136331364313653150031511
12111466
Anti-Roll Bar Cups, SetAnti-Roll Bar Ballstud,blue aluminumTC6.1 Anti-Roll Bar KitTC6.1 Anti-Roll Bar TubeTC6.1 Anti-Roll Bar Wire, SetTC6.1 Anti-Roll Bar MountsM3x2.5mm Set ScrewM2x5mm SHCS
31325
31327
31324540731324
31327
31326
31326
Front3942Rear3941
6475
31305
31324
31329
31328
3150031500
31363
3150031500
31362
31362
31364
31364
8828
31058
31511
3151131511
31511
3126931365
31365
5420542154225423542454255426542754285429543054315432543354345435543654375438
2oz.2oz.2oz.2oz.2oz.2oz.2oz.2oz.2oz.2oz.2oz.2oz.2oz.2oz.2oz.2oz.2oz.2oz.2oz.
10 Weight Silicone Shock Fluid20 Weight Silicone Shock Fluid30 Weight Silicone Shock Fluid40 Weight Silicone Shock Fluid22.5 Weight Silicone Shock Fluid80 Weight Silicone Shock Fluid27.5 Weight Silicone Shock Fluid15 Weight Silicone Shock Fluid25 Weight Silicone Shock Fluid35 Weight Silicone Shock Fluid45 Weight Silicone Shock Fluid55 Weight Silicone Shock Fluid32.5 Weight Silicone Shock Fluid37.5 Weight Silicone Shock Fluid42.5 Weight Silicone Shock Fluid50 Weight Silicone Shock Fluid60 Weight Silicone Shock Fluid70 Weight Silicone Shock Fluid47.5 Weight Silicone Shock Fluid
31:: Front Spool
:: Rear Gear Differential
:: Spur Gear Assembly6111122166
31160311623131431315313193132031331313333152131530
3mm E-ClipAxle Shim KitTC6 Spur Gear HubTC6 Spur Gear ShaftTC6 Spur Clamping RingTC6 Spur Pulley (20T)4x8x3mm Flanged BearingTC6 Spur Gear (87T/48P)M2.5x0.5x8mm BHCSM3x0.5x5mm BHCS
31521
31521
31160
31162
31162
31160
31331
31331
31315
31320
31320
31530
31530
31319
3131431333
31162311753118431185314013133931341313423135031510
1112214166
611221121
11
46753116231184311853140131344313453134631347
3134831349
See page 30 for shock fluids for use with the TC6.1 gear differential.
Axle Shim KitOneway/Spool PulleyCam Holder SetDiff Bearing Cam10 x 15mm BearingTC6 Spool KitTC6 Spool OutdrivesTC6 Spool HubM2.5x10mm FHCSM2x4mm BHCS
M2.5 X .45 X 6 FHCSAxle Shim KitCam Holder SetDiff Bearing Cam10 x 15mm BearingTC6 Gear DiffTC6 Gear Diff RebuildTC6 Gear Diff OutdrivesTC6 Gear Diff Case, O-Ring, PulleyTC6 Gear Diff Pins & ShimsTC6 Gear Diff Seals
31175
31342
31350
3135031401
31401
31341
31341
31162
31162
31510
31510
31348
3134831345
31348
31345
31345
3134531348 31348
31348
31348
31348
31346
313464675
467531162
31162
31401
31401
31348
31349
31349
31349
31349 3134831347
31347
31345
31184
31184
31185
31185
32:: Steering Bellcrank and Servo Mounts
:: Front Bumper
:: Front and Rear Shock Towers
7336733791803124631280312863130631307313083140331530315323154089007
141
Pr.6111126661
1736223038974673252012520225203313163131731530
6116
202020116
6114611166666
17362230389731250312813130231303313103153031531315323154131550
Steering Servo Mount Kit.250” x.125” x.015” WasherServo Horns, MoldedServo Mounts5mm Ballstud, shortAluminum Ballstud Washers, SetTC6 Servo Saver Tube AssemblyTC6 Steering PostTC6 Bellcrank Assembly4x7mm BearingM3x5mm BHCSM3x8mm BHCSM3x5mm FHCSSteering Servo Horn (Ring)
FT Body Clips, shortF/R Body Mounts, SetPivoting Body Mounts, SetM2.5x4mm BHCSM3x8mm FHCSM3x10mm FHCSM3x12mm FHCSTC6 Bumper and BraceTC6 Foam BumperM3x5mm BHCS
FT Body Clips, shortF/R Body Mounts, SetPivoting Body Mounts, SetShock Bushing8mm Ballstud, shortTC6 Shock Tower, FrontTC6 Shock Tower, RearTC6 Bearing CapM3x5mm BHCSM3x6mm BHCSM3x8mm BHCSM3x6mm FHCSM3 Aluminum Locknut
31308
3128031280
9180 89007
31286
3128031532
31308
31532
31532
31532
7337
7336
733631540
31246
31246
31540
7337
7337
733731532
31306
31403
3140331307
31308
3897
17362230
2230
31316
25202
25202
31317
31316
25203
2520325203
25201
4673
31530 3897
31307
31530
31308
31306
31306
1736
17362230
2230
31530
31550
31250
31303
31532
3153231250
31531
3153131541
3154131281
31281
31531
3153131531
31531 3131031310
3897
3897
31530
31530
31550
31550
31250
31250
31302
31281
31281
31531
31531
31541
31541
31531
31531
31531
31531
3131031310
33:: Front Bulkhead
:: Rear Bulkhead
25187252272523731112311623119831200312143122131222312343128031284312863130931321313223135631358313603136131365313703151031511315323154091148
202028111
Pr.114661118
Pr.Pr.Pr.11466668
20208111114661118
Pr.Pr.11426668
25187252273111231162311983120031221312223123431280312843128631309313213132231357313593136131365313703140431510315113154091148
M3x14mm BHCSM4x8mm Setscrew5x10mm Bearing1/16” x 5/16” Dowel PinsAxle Shim KitArm Mount Shim SetWheelbase Shim SetCaster Block BushingInner Hinge Pin SetOuter Hinge Pin SetClamping Wheel Hex5mm Ballstud, short8mm Ballstud, longAluminum Ballstud Washers, SetTC6 BulkheadTC6 Arm Mount SetTC6 Arm Mount BushingTC6.1 Front ArmsTC6.1 Caster BlocksTC6.1 Steering BlocksTC6.1 Offset Arm Mounts, SetTC6.1 Anti Roll Bar Mounts, SetTC6.1 Axle Crush TubesM2x4mm BHCSM2x5mm SHCSM3x8mm BHCSM3x5mm FHCSM4 Locknut
M3x14mm BHCSM4x8mm Setscrew1/16” x 5/16” Dowel PinsAxle Shim KitArm Mount Shim SetWheelbase Shim SetInner Hinge Pin SetOuter Hinge Pin SetClamping Wheel Hex5mm Ballstud, short8mm Ballstud, longAluminum Ballstud Washers, SetTC6 BulkheadTC6 Arm Mount SetTC6 Arm Mount BushingTC6.1 Rear ArmsTC6.1 Rear Hub CarrierTC6.1 Offset Arm Mounts, SetTC6.1 Anti Roll Bar Mounts, SetTC6.1 Axle Crush Tubes6x10mm BearingM2x4mm BHCSM2x5mm SHCSM3x5mm FHCSM4 Locknut
31511
31365
31309
2518731221
31280
3151031222
31356
31358
31358
31359
31359
91148
91148
31356
25227
31200
31200
31284
31532
31358
31360
31280
31511
3123431112
25237
2523731214
3137031162
25187
31322
31322
31361
31361
31198
31198
31540
31540
31511
31365
31309
31511
31234
31112
31162
25187
25187
31322
3132231321
31198
3119825227
31221
31200
3151031280
31222
3128131286
31357
31357
31200
31361
31540
31540
25237
25237
3135931370
34:: Chassis / Top Plate / Belts / Antenna / Battery Braces / Motor Mount
:: Lubes & Adhesives
:: Decals
:: Pinions / Spur Gears
6338311873118831286313003130131304313113131231313313183150031530315313153231540
111111
Pr.Pr.11166666
1105159615976588659166366727
71671738163820383431299
82538254825582568257825882598260826182628263826482658266826782688269827082718272
39213922392339923993399439954462461531332313333133431335
1111112
111121
11111111111111111111
1111111111111
Antenna Tube 12”, blackFront BeltRear BeltAluminum Ballstud Washers, SetTC6 ChassisTC6 Top PlateTC6 Battery Tape TabTC6 Spur Gear BulkheadTC6 Motor MountTC6 Motor Mount BraceTC6 Battery Brace SetM3x2.5mm Set ScrewM3x5mm BHCSM3x6mm BHCSM3x8mm BHCSM3x5mm FHCS
FT Green Slime Shock LubeFT Locking AdhesiveFT Tire Adhesive, mediumBlack Grease - 4ccS.Diff Lube - 4ccSilicone Grease - 4ccServo Tape
Reedy 2009 Sticker SetReedy Powered Logo DecalAmerican Bumper StickerAE Logo Decal SheetAE Blue Embossed Logo StickerTC6 Decal Sheet
16T 48P Pinion Gear17T 48P Pinion Gear18T 48P Pinion Gear19T 48P Pinion Gear20T 48P Pinion Gear21T 48P Pinion Gear22T 48P Pinion Gear23T 48P Pinion Gear24T 48P Pinion Gear25T 48P Pinion Gear26T 48P Pinion Gear27T 48P Pinion Gear28T 48P Pinion Gear29T 48P Pinion Gear30T 48P Pinion Gear31T 48P Pinion Gear32T 48P Pinion Gear33T 48P Pinion Gear34T 48P Pinion Gear35T 48P Pinion Gear
69T 48P Spur Gear72T 48P Spur Gear75T 48P Spur Gear76T 48P Spur Gear77T 48P Spur Gear73T 48P Spur Gear74T 48P Spur Gear100T 64P Spur Gear96T 64P Spur Gear80T 48P Spur Gear87T 48P Spur Gear106T 64P Spur Gear115T 64P Spur Gear
1166666
TC6 Motor Mount Brace
6338
31500
31530
31530
31530
31530
31304
31304
31318
31318
3154031540
3154031540
31318
3154031540
31318
31540
31300
31187
31188
3130131540
31540
31540
31531
31312
3131331540
3154031531
3153131286
31286
31311
31311
31540
3153231540
31530
35:: Factory Team and Option Parts
:: Reedy Motors and ESC’s
:: XP Electronics
:: Reedy Batteries and Chargers
:: Reedy Accessories
140114041734173517363927392839914617
2539131280312813128231283312843128531286312883128931290312913129231293312963133931344313513155031551
9169179189199369379389399409419429439449459469479489499509519529659669679626
291252912629140291432916629167292092921029211292122922129222
22104611412
106666661222222111166
1111111111111111111111111
111111111111
302303601604609610627628629632633634637681682683684686689693694695696700709710712713714723730731732734735
605654655656657658659660661662663664716954955956957958
SP35**SP36**SP417SP418
11111111111111111111111111111111111
1111111111111111111111
FT Blue Titanium Turnbuckle 1.300”FT Blue Titanium Turnbuckle 1.775”FT Blue Body Clip, 4 long, 6 shortFT Blue Body Clip, longFT Blue Body Clip, shortRadial Heatsink, narrowRadial Heatsink, wideTC Aero Dish Wheel 24mm12R5 Front Bulkhead Shims (x4 0.5mm, x4 1.0mm, x4 2.0mm)FT 4mm Locknuts, blue5mm Ballstud, short8mm Ballstud, short10mm Ballstud, short5mm Ballstud, long8mm Ballstud, long10mm Ballstud, longAluminum Ballstud Washer, SetTi Nitride Ballstuds M3x5mm, shortTi Nitride Ballstuds M3x8mm, shortTi Nitride Ballstuds M3x10mm, shortTi Nitride Ballstuds M3x5mm, longTi Nitride Ballstuds M3x8mm, longTi Nitride Ballstuds M3x10mm, longTC6 Ballast WeightTC6 Spool KitTC6 Gear Differential KitFT TC6 Aluminum Screw KitM3 Aluminum Lock NutM4 Aluminum Flange Lock Nut
540R Brushless Motor 3300kV540R Brushless Motor 3900kV540R Brushless Motor 4900kV540R Brushless Motor 6100kVXP SC450-BL/Reedy 540R 3300kV ComboXP SC450-BL/Reedy 540R 3900kV ComboXP SC450-BL/Reedy 540R 4900kV ComboXP SC450-BL/Reedy 540R 6100kV ComboReedy Sonic 21.5 Stock (sensored)Reedy Sonic 17.5 Stock (sensored)Reedy Sonic 13.5 Stock (sensored)Reedy Sonic 10.5 Modified (sensored)Reedy Sonic 9.5 Modified (sensored)Reedy Sonic 8.5 Modified (sensored)Reedy Sonic 7.5 Modified (sensored)Reedy Sonic 6.5 Modified (sensored)Reedy Sonic 5.5 Modified (sensored)Reedy Sonic 5.0 Modified (sensored)Reedy Sonic 4.5 Modified (sensored)Reedy Sonic 4.0 Modified (sensored)Reedy Sonic 3.5 Modified (sensored)XP SC700-BL/Reedy 540-SL 3300kV ComboXP SC700-BL/Reedy 540-SL 3900kV ComboXP SC700-BL/Reedy 540-SL 4900kV ComboReedy Radon 30000 rpm
S1903MG ServoS2008MG ServoXP SC200 Brushed ESC XP SC700-BL Brushless ESCXP DS1313 Digital ServoXP DS1015 Digital ServoGear Set, DS1313Gear Set, DS1015Servo Case , DS1313/DS1015Accessory Pack, DS1313/DS1015XP3SS 2.4GHz Radio SystemTRS401SS 2.4GHz 4Ch Receiver
AA Alkaline 1.5V (4)AA 2700mAh NiMH 1.2V Rechargeable (4)LiPo 65C 6500mAh 7.4VReedy 526-S AC/DC 2S-6S Cell LiPo/LiFe ChargerTamiya to DEANS® Plug AdaptorReedy Charger NiCD/NiMHLiPo 60C 5200mAh 7.4V SPLiPo 60C 5500mAh 7.4V LiPo 60C 5500mAh 3.7V TX Lightweight Battery 1350mAh 11.1VTX Battery - 3PK, M11 3000mAh 11.1VTX Battery - Helios, Z1 2400mAh 11.1VTX Battery - M11X 2500mAh 7.4VWolfpack 2400mAh 7.2V w/DEANS® connectorWolfpack 3000mAh 7.2V w/DEANS® connectorWolfpack 3600mAh 7.2V w/DEANS® connectorWolfpack 4200mAh 7.2V w/DEANS® connector LiPo 40C+ 4200mAh 7.4V SPR-Power 1700mAh 7.2V w/TAM connectorWolfpack 2400mAh 7.2V w/TAM connectorWolfpack 3000mAh 7.2V w/TAM connectorWolfpack 3600mAh 7.2V w/TAM connectorWolfpack 2400mAh 7.2V w/TRA connectorWolfpack 4200mAh 7.2V w/TAM connectorLiPo 5000mAh 7.4V 35C ROAR SpecLiPo 5100mAh 7.4V 35C SP ROAR SpecLiPo 4200mAh 7.4V 35C SP EFRA SpecLiPo 2400mAh 7.4V 20C StickLiPo 3400mAh 7.4V 25C StickLiFe 4000mAh 6.6V 30CWolfpack LiPo 3000mAh 7.4V 35C w/DEANS®Wolfpack LiPo 3300mAh 7.4V 35C w/DEANS®Wolfpack LiPo 3400mAh 7.4V 35C w/DEANS®Wolfpack LiPo 6500mAh 7.4V 25C w/DEANS®Wolfpack LiPo 3900mAh 11.1V 35C w/DEANS®
Motor Cooling Fans (2)4.0mm plugs (2M, 2F) 4.0mm plugs (2M, 10F) 4.0mm plugs (10F)4.0mm plugs (100F)4.0mm plugs (10M)4.0mm plugs (30M)3.5mm plugs (3M, 3F)3.5mm plugs (10F)3.5mm plugs (100F)3.5mm plugs (10M)3.5mm plugs (30M)Reedy 09 Decal SetSonic Stock Rotor 12.3 x 24.2 (7.25)Sonic Stock Rotor 12.3 x 25.0 (7.25)Sonic Stock Rotor 12.5 x 25.0 (7.25)Sonic Modified Rotor 12.2 x 25.0 (5.0)Sonic Modified Rotor 12.5 x 25.0 (5.0)Reedy Logo T-Shirt - White (M, L, XL, XXL, XXXL)Reedy Logo T-Shirt - Black (M, L, XL, XXL, XXXL)Factory Team 1/10 Motor Storage BagFactory Team 1/10 Car Carrier Bag
** Use part number plus the desired size when ordering!
36
:: LRP Brushless Motors
:: LRP Misc.
:: LRP Speed Controls :: LRP Brushless Combos
:: LRP Charger, Power Supply, Balancer, Iron
LRP50430LRP50440LRP50450LRP50460LRP50480LRP50642LRP50652LRP50653LRP50662LRP50672 LRP50673LRP50682LRP50683LRP50687LRP50688LRP50691LRP50692LRP50693LRP50701LRP50702LRP50712LRP50722LRP50832LRP50842LRP50852LRP50862
LRP50620LRP50621LRP50622LRP50623 LRP50624LRP50625LRP50626LRP50632 LRP50633LRP50634LRP50635LRP50636LRP50637LRP50638LRP50639LRP64790LRP80135LRP82512LRP82515LRP82520LRP82521LRP82530LRP82531LRP819307LRP819310LRP819315LRP819320
LRP80705LRP80905LRP80915LRP80955
LRP80673LRP80674LRP80675LRP80677LRP80678LRP80679LRP80680LRP80694LRP80695LRP80696LRP80697LRP80698LRP80699LRP80790LRP80791LRP80792LRP80793LRP80794LRP80795LRP80796LRP80797LRP80798LRP80799
2922529226292272922829229292302923129234292352923629237292382923929240292412924229243292442924529246
LRP41281LRP41552LRP41555LRP42103LRP42104LRP42105LRP42305LRP42306LRP43150LRP45200 LRP65800LRP65802LRP65803LRP65804LRP81800
11111111111111111111111111
111111111111111111111111111
1111
1111111111111111111111111111111111111111111
111111111111111
Vector K4 6.5 TurnVector K4 8.5 TurnVector K4 10.5 TurnVector K4 13.5 TurnVector K4 17.5 TurnVector X-12 9.5 TurnVector X-12 8.5 TurnVector X-12 OCTA Wind 8.5 TurnVector X-12 7.5 TurnVector X-12 6.5 TurnVector X-12 OCTA Wind 6.5 TurnVector X-12 5.5 TurnVector X-12 OCTA Wind 5.5 TurnVector X-12 5.0 TurnVector X-12 OCTA Wind 5.0 TurnVector X-11 4.5 TurnVector X-12 4.5 TurnVector X-12 OCTA Wind 4.5 TurnVector X-11 4.0 TurnVector X-12 4.0 TurnVector X-12 3.5 TurnVector X-12 3.0 TurnVector X-12 Stockspec 10.5 TurnVector X-12 Stockspec 13.5 TurnVector X-12 Stockspec 17.5 TurnVector X-12 Stockspec 21.5 Turn
X-12 Replacement Ball BearingsX-12 Optional Ceramic Ball BearingsX-12 Small Parts Set X-12 PreciSensor Unit X-12 Replacement Aluminum Front CanX-12 Lightweight Aluminum CanX-12 Alum Rear Cover X-12 12.0mm Sintered RotorX-12 12.5mm Sintered RotorX-12 13.0mm Sintered RotorX-12 Stock Spec Rotor 12.45mmWorks Team X-12 12.0mm RotorWorks Team X-12 12.5mm RotorWorks Team X-12 13.0mm RotorX-12 Stock Spec 1S LiPo RotorLRP Motor Bearing PullerBEC Stabilizing Capacitor SXX Low Profile Fan 30mm Motor Fan/Clamp, GunmetalRadical Cooling Set, BlueRadical Cooling Set, Gunmetal SXX Power Cap 3.7-4.8V SXX Power Cap 6.0-7.4V70mm High Flex Sensor Wire100mm High Flex Sensor Wire150mm High Flex Sensor Wire200mm High Flex Sensor Wire
SPX ZeroSXX Comp v.2 Speed ControlSXX Stock-Spec v.2SXX TC-Spec v.2 Speed Control
SXX SS / 10.5T SS SXX SS / 13.5T SS SXX SS / 17.5T SSSXX SS v.2 / 10.5T SSSXX SS v.2 / 13.5T SSSXX SS v.2 / 17.5T SSSXX SS v.2 / 21.5T SSSXX Comp v.2 / X-12 5.0TSXX Comp v.2 / X-12 5.5TSXX Comp v.2 / X-12 6.5TSXX Comp v.2 / X-12 7.5TSXX Comp v.2 / X-12 8.5TSXX Comp v.2 / X-12 9.5TSXX TC v.2 / X-12 3.0TSXX TC v.2 / X-12 3.5TSXX TC v.2 / X-12 4.0TSXX TC v.2 / X-12 4.5TSXX TC v.2 / X-12 5.0TSXX TC v.2 / X-12 5.5TSXX TC v.2 / X-12 6.5TSXX TC v.2 / X-12 7.5TSXX TC v.2 / X-12 8.5TSXX TC v.2 / X-12 9.5TSonic 9.5T / SXX Comp v.2Sonic 8.5T / SXX Comp v.2Sonic 7.5T / SXX Comp v.2Sonic 6.5T / SXX Comp v.2Sonic 5.5T / SXX Comp v.2Sonic 5.0T / SXX Comp v.2Sonic 4.5T / SXX Comp v.2Sonic 21.5T / SXX SS v.2Sonic 17.5T / SXX SS v.2Sonic 13.5T / SXX SS v.2Sonic 10.5T / SXX SS v.2Sonic 9.5T / SXX TC v.2Sonic 8.5T / SXX TC v.2Sonic 7.5T / SXX TC v.2Sonic 6.5T / SXX TC v.2Sonic 5.5T / SXX TC v.2Sonic 5.0T / SXX TC v.2Sonic 4.5T / SXX TC v.2Sonic 4.0T / SXX TC v.2Sonic 3.5T / SXX TC v.2
Quadra Pro 2 ChargerPulsar Competition 3 Charger Pulsar Touch Charger LiPo Balance Board XHLiPo Balance Board FP/TP LiPo Balance Board PQ Temp. Sensor for Pulsar TouchSensor Wire Splitter Power Supply Competition LiPo Parallel BalancerHigh Power Solder StationSoldering Tip 5mm Soldering Tip 1.2mm Soldering Handle LRP Speedo Updater
:: 1/18 Kits and RTR’s
:: 1/12, 1/10 Kits and RTR’s
201002010120103201042010520106201082011020115201182012120130
20332042401970207023702770297030703270347036703770467047704870497080709280208021903490369039906090612051530105301063011190004900059000690007
111111111111
111111111111111111111111111111111
RC18T RTR (ready-to-run)RC18T2 2.4ghz RTR (ready-to-run)RC18B2 - RC18T2 Team KitRC18T2 Brushless RTR (ready-to-run)RC18B RTR (ready-to-run)RC18B2 2.4ghz RTR (ready-to-run)RC18B2 Brushless RTR (ready-to-run)RC18MT RTR (ready-to-run)RC18R Kamino RTR (ready-to-run)RC18R Niteline RTR (ready-to-run)SC18 Brushless RTR (ready-to-run)RC18LM RTR (ready-to-run)
FT Nitro TC3 KitNitro TC3 RTR Plus (ready-to-run)FT 12R5.1 KitRC10T4 Team Truck KitRC10T4.1 FT KitSC10 2WD Short Course Race Truck KitSC10 Associated/RC10.com Truck RTR (ready-to-run)SC10 KMC Wheels Race Truck RTR (ready-to-run)SC10 Ready Lift RTR (ready-to-run)SC10 FT KitRC10T4.1 RTR 2.4GHz Brushed (ready-to-run)RC10T4.1 RTR 2.4GHz Brushless (ready-to-run)SC10 RS RTR, 2.4ghz Brushless Lucas Oil BodySC10 RS RTR, 2.4ghz Brushless Monster Energy BodySC10 RS RTR, 2.4ghz Brushless Pro Comp BodySC10 RTR, 2.4ghz Brushless Rockstar/Makita BodyFT GT2 Nitro Truck KitGT2 RS Truck Nitro RTR (ready-to-run)FT RC10R5 KitFT RC10R5-OVAL KitRC10B4 Buggy Team KitRC10B4.1 FT KitRC10B4.1 RTR 2.4GHz Brushless (ready-to-run)FT B44 4WD Buggy KitFT B44.1 4WD Buggy KitMGT 3.0 Nitro Monster Truck RTR (ready-to-run)FT TC5R Rubber Tire Edition 4WD Touring Car KitFT TC6 4WD Touring Car KitTC4 4WD Touring Car RTR (ready-to-run)SC10 4x4 KitSC10 4x4 Lucas Oil RTR (ready-to-run)SC10 4x4 Pro Comp RTR (ready-to-run)SC10 4x4 Rockstar/Makita RTR (ready-to-run)
:: 1/8 Kits and RTR’s20503
20504
809048090580906809078091280922
80923
80924
80925
80932
1
1
111111
1
1
1
1
Limited Edition MGT 4.60 Nitro RTR, w/flag body (ready-to-run)Limited Edition MGT 8.0 Nitro RTR, w/flag body (ready-to-run)FT RC8Be Electric Buggy KitRC8RS “Race Spec” Nitro Buggy RTR (ready-to-run)RC8.2 FT Nitro Buggy KitRC8.2e FT Electric Buggy KitRC8T Championship EditionSC8 Short Course Race Truck, KMC Wheels Nitro RTR (ready-to-run)SC8 Short Course Race Truck, Bully Dog Nitro RTR (ready-to-run)SC8 Short Course Race Truck, AE Team Nitro RTR (ready-to-run)SC8 Short Course Race Truck, Pro Comp Nitro RTR (ready-to-run)SC8e Short Course Race Truck Rockstar/Makita RTR (ready-to-run)
37:: Tools1111145015411542154315441545154615471548155115531554156115621563156415651566156715891590159216551656165716581659166016611662166316641665166616671668166916701671167216731674
171917373718371937203987642969567709
1111111111111111111111111111111111111111111
11
121212111
12
FT Turnbuckle WrenchFT Ride Height GaugeFT Hex Driver Set, (7 pcs)FT .050” Silver Hex DriverFT 1/16” Black Hex DriverFT 1.5mm Purple Hex DriverFT 5/64” Blue Hex DriverFT 3/32” Gold Hex DriverFT 2.5mm Green Hex DriverFT 3mm Red Hex DriverFT Screwdriver SetFT Phillips Silver ScrewdriverFT Silver Spring Hook Tool FT Nut Driver Set, (6 pcs)FT 3/16” Black Nut DriverFT 1/4” Red Nut DriverFT 5.5mm Red Nut DriverFT 11/32” Green Nut DriverFT 7.0mm Silver Nut DriverFT 8mm Gold Nut DriverFT 5/64” Blue Ball Hex DriverFT 3/32” Gold Ball Hex DriverFT Ball Hex Driver Set, (3 pcs)FT 8-Piece 1/4” Hex Drive SetFT 1/4” Hex Drive Handle, without tipsFT 1/4” Hex Drive .050” TipFT 1/4” Hex Drive 1/16” TipFT 1/4” Hex Drive 5/64” - 2.0mm TipFT 1/4” Hex Drive 3/32” TipFT 1/4” Hex Drive 1.5mm TipFT 1/4” Hex Drive 2.5mm TipFT 1/4” Hex Drive 3/16” Nut Driver TipFT 1/4” Hex Drive 1/4” Nut Driver TipFT 1/4” Hex Drive 11/32” Nut Driver TipFT 1/4” Hex Drive 5.5mm Nut Driver TipFT 1/4” Hex Drive 7.0mm Nut Driver TipFT 1/4” Hex Drive 8.0mm Nut Driver TipFT 1/4” Hex Drive 5/64” - 2.0mm Ball End TipFT 1/4” Hex Drive 3/32” Ball End TipFT 1/4” Hex Drive Standard Screwdriver TipFT 1/4” Hex Drive Phillips Screwdriver TipFT 1/4” Hex Drive 2.5mm Ball End TipFT 1/4” 5 Piece Power Tool Tips Set (5/64-2.0mm, 1.5mm, 2.5mm, 5/64”- 2.0mm ball, 2.5mm ball)FT Camber + Track Width ToolFT Body Scissors12 Inch Nylon Wire Ties6 Inch Nylon Wire Ties8 Inch Nylon Wire TiesFT Droop GaugeShock Building ToolMolded Tools, Set4 Inch Nylon Wire Ties
38:: Contact Information
Associated Electrics, Inc.26021 Commercentre Drive
Lake Forest, CA 92630-8853 USAhttp://www.TeamAssociated.com
http://www.RC10.comhttp://twitter/Team Associated
http://bit.ly/AEonFacebook
call: (949) 544-7500fax: (949) 544-7501
Check out the following web sites for all of our electric kits, current products, new releases, setup help, tips, and racing info!
www.TeamAssociated.com. - www.RC10.com
:: Apparel
:: Notes
** Use part number plus the desired size when ordering!
SP35**SP36**SP62**SP63**SP64**SP65**SP66**SP67**SP69**SP41l**SP416SP417SP418
SP420**715
110684
1111111111111
Pr.11
Reedy 09’ White T-Shirt (M, L, XL, XXL, XXXL)Reedy 09’ Black T-Shirt (M, L, XL, XXL, XXXL)AE Vertigo Long Sleeve T-Shirt (S, M, L, XL, XXL)AE Vertigo White T-Shirt (S, M, L, XL, XXL)AE Vertigo Blue T-Shirt (S, M, L, XL, XXL)AE Vertigo Black T-Shirt (S, M, L, XL, XXL)AE Stencil Blue T-Shirt (S, M, L, XL, XXL, XXXL)AE Stencil Sweatshirt (S, M, L, XL, XXL, XXXL)26-Time Champ T-Shirt (S, M, L, XL, XXL, XXXL)AE Hat ‘11, Flatbill Black (S-M, L-XL)1/10 Car Carrier Bag Only1/10 FT Motor Bag1/10 FT Car Carrier Bag with Boxes, SetAE Pit Gloves (M, L, XL)Reedy 2009 Track BannerTeam Associated Track Banner
Rid
e Heig
ht
Cam
ber
N/A
N/A
N/A
N/A
N/A
Caster
Rea
r Hub To
eTo
e (Tota
l)
Hex
Spacin
g
Wheelb
ase
Steering B
ellcrank
Steering Lin
k
Bum
psteer
Notes:
Driver:
Date:
Track
:
Even
t:
Conditio
ns:
Rev.1
Setu
p Sh
eet
FrontRear
:: For m
ore setu
ps, visit R
C10.co
m a
nd click
on “
Setup Sh
eets”
Alig
nm
ent
Susp
ensio
n G
eom
etry
Shock
s
Differen
tials
Tires
Chassis
Batte
ry Pla
cem
ent
Moto
rB
ody &
Win
gG
earin
g
Shock
Positio
n
Oil
Type
Type
Cam
ber Lin
k P
ositio
n
Pisto
n
Setting
Tire Dia
meter
Outer B
all &
Shim
s
Reb
ound
Cam
Hold
er
Insert &
Wheel
FWD
Arm
Mount
Sprin
g
Belt Ten
sion N
um
ber
Additive &
Am
ount
Transm
itter
Speed
Contro
lTu
rnin
g C
ircle:
E.S
.C. Typ
e:
Steerin
g E
xpo:
E.S
.C. Se
ttings:
S.W
. Ver.
Bra
ke E
.P. :
Thro
ttle E
xpo:
FWD
Mount Sh
im
RW
D A
rm M
ount
RW
D M
ount Sh
ims
Dro
op
Anti-R
oll B
ar
Notes:
Notes:
Notes:
Notes:
/
Notes:
Note
s:N
ote
s:N
otes:
Notes:
Chassis
Top P
late
Front
Rea
r
Wheel B
ase Sh
ims
1mm
2m
m
Belt
Tensio
nN
um
ber
Vie
w fr
om
left
sid
e o
f car
1732
161
Cam
Hold
er
AB
1º1.5
º2º
Arm
Mount Sh
ims
Steering B
ellcrank
78
AB
C
RW
D M
ount
RW
D M
ount
FW
D M
ount
FW
D M
ount
FR
ON
T O
F C
AR
FR
ON
T O
F C
AR
AA
AA
BB
BB
AB
21
Wheelb
ase
Wheelb
ase
Toe
0+ -To
e0+ -
Bum
psteer
Cam
ber
Cam
ber
Steerin
g L
ink
Arm
Mounts
Roll C
ente
rLo
w
Hig
hStd
Offse
t0
12
3
BC
Cam
ber
1
17
AB
C
2
3
3
5
4
2
5
4
6
6
0
+
-
Outer B
all
& S
him
s
Cam
ber
12
34
56
7
12
34
56
7
Hex S
pacin
gH
ex S
pacin
g
0
+
-
AB
C
Outer B
all
& S
him
s
AB
Droop
Droop
5m
m5m
m
-1.5
deg
-2.5
deg
0 d
eg
-2 d
eg
4 d
eg
0 d
eg0 d
eg
0 d
eg0 d
eg
+ 0
.5 d
eg
1m
m1m
m
1.1
mm
0.9
mm
7B3
3A
Silver +2m
m
6
40w
t40w
t
#2
#2
AA
50%
50%
2B
0B
- Offset
0B
- Offset
87
3C
3C
0B
0B
- Offset
5
Bla
ck
Silver
SilverSilver
Spool
Gea
r Diff
40w
t
00
40
2.5x10mm (31350)
3x5mm (31540)
3x6mm (31541)
3x8mm (25201)
3x10mm (25202)
3x12mm (25203)
3x16mm (25204)
2x4mm (31510)
2x5mm (31511)
2.5x4mm (4673)
2.5x6mm (4675)
2.5x8mm (31521)
3x5mm (31530)
3x6mm (31531)
3x8mm (31532)
3x12mm (89202)
3x14mm (25187)
3x16mm (89203)
:: Hardware - 1:1 Scale View
Cap Head (shcs)
Setscrew
Notes:
Flat Head (fhcs) Button Head (bhcs)
2-56 locknut (3904)
M3 locknut (31550)
M4 locknut (91148)
Nuts (lock/plain)1mm and 2mmblue shims (31286)
Diff washer (31166)
1mm and 2mmwheelbase shims (31200)
Thrust washer (6573)
Gold washer (7337)
Diff shim (31162)
Shims and Washers
2x5mm (31511)
Thrust screw (9274)
3x2.5mm (31500)
4x8mm (25227)
Ball Bearings
4x7mm (31403)
4x8x3mm flanged (31331)
5x8mm (31400)
5x10mm (25237)
10x15mm (31401)
E-clip (31160)
C-clip (31307)
Clips
Ballstuds
Black 5mm short (31280)(Ti Nitride 5mm short, 31288)
Silver 8mm short (31283)(Ti Nitride 5mm long, 31291)
Black 8mm short (31281)(Ti Nitride 8mm short, 31289)
Silver 8mm long (31284)(Ti Nitride 8mm long, 31292)
Black 10mm short (31285)(Ti Nitride 10mm short, 31290)
Silver 10mm long (31285)(Ti Nitride 10mm long, 31293)
Rid
e Heig
ht
Cam
ber
N/A
N/A
N/A
N/A
N/A
Caster
Rea
r Hub To
eTo
e (Tota
l)
Hex
Spacin
g
Wheelb
ase
Steering B
ellcrank
Steering Lin
k
Bum
psteer
Notes:
Driver:
Date:
Track
:
Even
t:
Conditio
ns:
Rev.1
Setu
p Sh
eet
FrontRear
:: For m
ore setu
ps, visit R
C10.co
m a
nd click
on “
Setup Sh
eets”
Alig
nm
ent
Susp
ensio
n G
eom
etry
Shock
s
Differen
tials
Tires
Chassis
Batte
ry Pla
cem
ent
Moto
rB
ody &
Win
gG
earin
g
Shock
Positio
n
Oil
Type
Type
Cam
ber Lin
k P
ositio
n
Pisto
n
Setting
Tire Dia
meter
Outer B
all &
Shim
s
Reb
ound
Cam
Hold
er
Insert &
Wheel
FWD
Arm
Mount
Sprin
g
Belt Ten
sion N
um
ber
Additive &
Am
ount
Transm
itter
Speed
Contro
lTu
rnin
g C
ircle:
E.S
.C. Typ
e:
Steerin
g E
xpo:
E.S
.C. Se
ttings:
S.W
. Ver.
Bra
ke E
.P. :
Thro
ttle E
xpo:
FWD
Mount Sh
im
RW
D A
rm M
ount
RW
D M
ount Sh
ims
Dro
op
Anti-R
oll B
ar
Notes:
Notes:
Notes:
Notes:
/
Notes:
Note
s:N
ote
s:N
otes:
Notes:
Chassis
Top P
late
Front
Rea
r
Wheel B
ase Sh
ims
1mm
2m
m
Belt
Tensio
nN
um
ber
Vie
w fr
om
left
sid
e o
f car
1732
161
Cam
Hold
er
AB
1º1.5
º2º
Arm
Mount Sh
ims
Steering B
ellcrank
78
AB
C
RW
D M
ount
RW
D M
ount
FW
D M
ount
FW
D M
ount
FR
ON
T O
F C
AR
FR
ON
T O
F C
AR
AA
AA
BB
BB
AB
21
Wheelb
ase
Wheelb
ase
Toe
0+ -To
e0+ -
Bum
psteer
Cam
ber
Cam
ber
Steerin
g L
ink
Arm
Mounts
Roll C
ente
rLo
w
Hig
hStd
Offse
t0
12
3
BC
Cam
ber
1
17
AB
C
2
3
3
5
4
2
5
4
6
6
0
+
-
Outer B
all
& S
him
s
Cam
ber
12
34
56
7
12
34
56
7
Hex S
pacin
gH
ex S
pacin
g
0
+
-
AB
C
Outer B
all
& S
him
s
AB
Droop
Droop
Associated Electrics, Inc.26021 Com
mercentre Dr.
Lake Forest, CA 92630 USAhttp://w
ww
.TeamAssociated.com
http://ww
w.RC10.com
http://twitter/Team
_Associatedhttp://bit.ly/AEonFacebook
call: (949) 544-7500 - fax: (949) 544-7501Check out the follow
ing web sites for all of our kits,
current products, new releases, setup help, tips, and racing info!
ww
w.Team
Associated.com. - w
ww
.RC10.com