Chapter 74 Copper and articles thereof Chapter notes 1. In this chapter, the following expressions have the meanings hereby assigned to them: (a) Refined copper: Metal containing at least 99.85% by weight of copper; or Other elements Element Limiting content % by weight Ag Silver 0.25 As Arsenic 0.5 Cd Cadmium 1.3 Cr Chromium 1.4 Mg Magnesium 0.8 Pb Lead 1.5 S Sulphur 0.7 Sn Tin 0.8 Te Tellurium 0.8 Zn Zinc 1 Zr Zirconium 0.3 Other elements, each 0.3 (b) Copper alloys: Metallic substances other than unrefined copper in which copper predominates by weight over each of the other elements, provided that: (1) the content by weight of at least one of the other elements is greater than the limit specified in the foregoing table; or (2) the total content by weight of such other elements exceeds 2.5% (c) Master alloys: Alloys containing with other elements more than 10% by weight of copper, not usefully malleable and commonly used as an additive in the manufacture of other alloys or as de- oxidants, de-sulphurising agents or for similar uses in the metallurgy of non-ferrous metals. However, copper phosphide (phosphor copper) containing more than 15% by weight of phosphorus falls in heading 2848. (d) Bars and rods: rolled, extruded, drawn or forged products, not in coils, which have a uniform solid cross- section along their whole length in the shape of circles, ovals, rectangles (including squares), equilateral triangles or regular convex polygons (including 'flattened circles' and 'modified rectangles', of which two opposite sides are convex arcs, the other two sides being straight, of equal length and parallel). Products with a rectangular (including square), triangular or polygonal cross-section may have corners rounded along their whole length. The thickness of such products which have a rectangular (including 'modified rectangular') cross- section exceeds one-tenth of the width. The expression also covers cast or sintered products, of the same forms and dimensions, which have been subsequently worked after production (otherwise than by simple trimming or de-scaling), provided that they have not thereby assumed the character of articles or products of other headings. Wire-bars and billets with their ends tapered or otherwise worked simply to facilitate their entry into machines for converting them into, for example, drawing stock (wire-rod) or tubes, are however to be taken to be unwrought copper of heading 7403. (e) Profiles: Rolled, extruded, drawn, forged or formed products, coiled or not, of a uniform cross- section along their whole length, which do not conform to any of the definitions of bars, rods, wire, plates, sheets, strip, foil, tubes or pipes. The expression also covers cast or sintered products, of the same forms, which have been subsequently worked after production (otherwise than by simple trimming or de-scaling), provided that they have not thereby assumed the character of articles or products of other headings. (f) Wire: Rolled, extruded or drawn products, in coils, which have a uniform solid cross-section along their whole length in the shape of circles, ovals, rectangles (including squares), equilateral triangles or regular convex polygons (including 'flattened circles' and 'modified rectangles', of which two opposite sides are convex arcs, the other two sides being straight, of equal length and parallel). Products with a rectangular (including square), triangular or polygonal cross-section may have corners rounded along their whole length. The thickness of such products which have a rectangular (including 'modified rectangular') cross-section exceeds one-tenth of the width. (g) Plates, sheets, strip and foil: Flat-surfaced products (other than the unwrought products of heading 7403), coiled or not, of solid rectangular (other than square) cross-section with or without rounded corners (including 'modified rectangles' of which two opposite sides are convex arcs, the other two sides being straight, of equal length and parallel) of a uniform thickness, which are: - of rectangular (including square) shape with a thickness not exceeding one-tenth of the width, - of a shape other than rectangular or square, of any size, provided that they do not assume the character of articles or products of other headings. Headings 7409 and 7410 apply, inter alia, to plates, sheets, strip and foil with patterns (for example, grooves, ribs, chequers, tears, buttons, lozenges) and to such products which have been perforated, corrugated, polished or coated, provided that they do not thereby assume the character of articles or products of other headings (h) Tubes and pipes: Hollow products, coiled or not, which have a uniform cross-section with only one enclosed void along their whole length in the shape of circles, ovals, rectangles (including squares), equilateral triangles or regular convex polygons, and which have a uniform wall thickness. Products with a rectangular (including square), equilateral triangular or regular convex polygonal cross-section, which may have corners rounded along their whole length, are also to be taken to be tubes and pipes provided the inner and outer cross- sections are concentric and have the same 27 February 2021 74 1 Customs Tariff Vol 2 Sect XV 74 01-74 19
Transcript
Chapter 74Copper and articles thereof
Chapter notes
1. In this chapter, the following expressions havethe meanings hereby assigned to them:
(a) Refined copper:Metal containing at least 99.85% by weight ofcopper; or
Other elements
Element Limiting content % by weight
Ag Silver 0.25
As Arsenic 0.5
Cd Cadmium 1.3
Cr Chromium 1.4
Mg Magnesium 0.8
Pb Lead 1.5
S Sulphur 0.7
Sn Tin 0.8
Te Tellurium 0.8
Zn Zinc 1
Zr Zirconium 0.3
Other elements, each 0.3
(b) Copper alloys:Metallic substances other than unrefinedcopper in which copper predominates byweight over each of the other elements,provided that:(1) the content by weight of at least one ofthe other elements is greater than the limitspecified in the foregoing table; or(2) the total content by weight of such otherelements exceeds 2.5%
(c) Master alloys:Alloys containing with other elements morethan 10% by weight of copper, not usefullymalleable and commonly used as an additivein the manufacture of other alloys or as de-oxidants, de-sulphurising agents or for similaruses in the metallurgy of non-ferrous metals.However, copper phosphide (phosphorcopper) containing more than 15% by weightof phosphorus falls in heading 2848.
(d) Bars and rods:rolled, extruded, drawn or forged products,not in coils, which have a uniform solid cross-
section along their whole length in the shapeof circles, ovals, rectangles (includingsquares), equilateral triangles or regularconvex polygons (including 'flattened circles'and 'modified rectangles', of which twoopposite sides are convex arcs, the other twosides being straight, of equal length andparallel). Products with a rectangular(including square), triangular or polygonalcross-section may have corners roundedalong their whole length. The thickness ofsuch products which have a rectangular(including 'modified rectangular') cross-section exceeds one-tenth of the width. Theexpression also covers cast or sinteredproducts, of the same forms and dimensions,which have been subsequently worked afterproduction (otherwise than by simpletrimming or de-scaling), provided that theyhave not thereby assumed the character ofarticles or products of other headings.Wire-bars and billets with their ends taperedor otherwise worked simply to facilitate theirentry into machines for converting them into,for example, drawing stock (wire-rod) ortubes, are however to be taken to beunwrought copper of heading 7403.
(e) Profiles:Rolled, extruded, drawn, forged or formedproducts, coiled or not, of a uniform cross-section along their whole length, which donot conform to any of the definitions of bars,rods, wire, plates, sheets, strip, foil, tubes orpipes. The expression also covers cast orsintered products, of the same forms, whichhave been subsequently worked afterproduction (otherwise than by simpletrimming or de-scaling), provided that theyhave not thereby assumed the character ofarticles or products of other headings.
(f) Wire:Rolled, extruded or drawn products, in coils,which have a uniform solid cross-sectionalong their whole length in the shape ofcircles, ovals, rectangles (including squares),equilateral triangles or regular convexpolygons (including 'flattened circles' and'modified rectangles', of which two oppositesides are convex arcs, the other two sides
being straight, of equal length and parallel).Products with a rectangular (includingsquare), triangular or polygonal cross-sectionmay have corners rounded along their wholelength. The thickness of such products whichhave a rectangular (including 'modifiedrectangular') cross-section exceeds one-tenthof the width.
(g) Plates, sheets, strip and foil:Flat-surfaced products (other than theunwrought products of heading 7403), coiledor not, of solid rectangular (other thansquare) cross-section with or withoutrounded corners (including 'modifiedrectangles' of which two opposite sides areconvex arcs, the other two sides beingstraight, of equal length and parallel) of auniform thickness, which are:
- of rectangular (including square) shapewith a thickness not exceeding one-tenthof the width,
- of a shape other than rectangular orsquare, of any size, provided that they donot assume the character of articles orproducts of other headings.Headings 7409 and 7410 apply, inter alia, toplates, sheets, strip and foil with patterns(for example, grooves, ribs, chequers,tears, buttons, lozenges) and to suchproducts which have been perforated,corrugated, polished or coated, providedthat they do not thereby assume thecharacter of articles or products of otherheadings
(h) Tubes and pipes:Hollow products, coiled or not, which have auniform cross-section with only one enclosedvoid along their whole length in the shape ofcircles, ovals, rectangles (including squares),equilateral triangles or regular convexpolygons, and which have a uniform wallthickness. Products with a rectangular(including square), equilateral triangular orregular convex polygonal cross-section, whichmay have corners rounded along their wholelength, are also to be taken to be tubes andpipes provided the inner and outer cross-sections are concentric and have the same
27 February 2021 74 1Customs Tariff Vol 2 Sect XV 74 01-74 19
form and orientation. Tubes and pipes of theforegoing cross-sections may be polished,coated, bent, threaded, drilled, waisted,expanded, cone-shaped or fitted with flanges,collars or rings.
Subheading notes
1. In this chapter, the following expressions have themeanings hereby assigned to them:
(a) Copper-zinc base alloys (brasses):Alloys of copper and zinc, with or without otherelements. When other elements are present:
- zinc predominates by weight over each of suchother elements,
- any nickel content by weight is less than 5%(see copper-nickel-zinc alloys (nickel silvers)),and
- any tin content by weight is less than 3% (seecopper-tin alloys (bronzes)).(b). Copper-tin base alloys (bronzes):Alloys of copper and tin, with or without otherelements. When other elements are present, tinpredominates by weight over each of such otherelements, except that when the tin content is3% or more the zinc content by weight mayexceed that of tin but must be less than 10%.
(c) Copper-nickel-zinc base alloys (nickel silvers):Alloys of copper, nickel and zinc, with or withoutother elements. The nickel content is 5% or moreby weight (see copper-zinc alloys (brasses)).
(d) Copper-nickel base alloys:Alloys of copper and nickel, with or without otherelements but in any case containing by weight notmore than 1% of zinc. When other elements arepresent, nickel predominates by weight over eachof such other elements
27 February 2021 74 2Customs Tariff Vol 2 Sect XV 74 01-74 19
- - Plates or sheets:- with at least one layer of woven glass fibre, impregnated witha fire- retardant artificial or synthetic resin with a glasstransition temperature (Tg) of more than 130 °C as measuredaccording to IPC-TM-650, method 2.4.25,- coated on one or both sides with a copper film with athickness of not more than 3,2 mm,and containing at least one of the following:- poly(tetrafluoroethylene) (CAS RN 9002-84-0)- poly(oxy-(2,6-dimethyl)-1,4-phenylene) (CAS RN 25134-01-4)- epoxy resin having a thermal expansion of not more than10 ppm in length and width and not more than 25 ppm inheightfor use in the manufacture of circuit boards
- - Plates or sheets consisting of- a layer of a silicon nitride ceramic with a thickness of 0,32mm (± 0,1 mm) or more but not more than 1,0 mm (± 0,1 mm),- covered on both sides with a foil of refined copper with athickness of 0,8 mm (± 0,1 mm) and- on one side partially covered with a coating of silver
74 10COPPER FOIL (WHETHER OR NOT PRINTED OR BACKED WITHPAPER, PAPERBOARD, PLASTICS OR SIMILAR BACKINGMATERIALS) OF A THICKNESS (EXCLUDING ANY BACKING)NOT EXCEEDING 0,15 MM
Not backed
- Of refined copper
27 February 2021 74 11Customs Tariff Vol 2 Sect XV 74 01-74 19
1 2A 2B 3 4 5 6 7
- - Refined copper foil and strips, electrolytically manufactured,with a thickness of at least 0,015 mm
- - Sheet or plate of polytetrafluoroethylene, containingaluminium oxide or titanium dioxide as filler or reinforced withglass-fibre fabric, covered on both sides with copper foil
27 February 2021 74 12Customs Tariff Vol 2 Sect XV 74 01-74 19
1 2A 2B 3 4 5 6 7
- - Foils, rolls composed of one layer of glass epoxy of 100 µmcolaminated with refined copper foil on one or two sides of35 µm with a tolerance of 10 % for use in the production ofsmart cards
- - Sheet or plates:- consisting of at least a central layer of paper or one centralsheet of any type of nonwoven fibre, laminated on each sidewith glass-fibre fabric and impregnated with epoxide resin, or- consisting of multiple layers of paper, impregnated withphenolic resin,coated on one or both sides with a copper film with amaximum thickness of 0,15 mm
- - Plates:-consisting of at least one layer of fibreglass fabric impregnatedwith thermosetting resin,-covered on one or both sides with copper foil with a thicknessof not more than 0,15 mm, and-with a dielectric constant (DK) of less than 3,9 and a loss factor(Df) of less than 0,015 at a measuring frequency of 10 GHz, asmeasured according to IPC-TM-650
27 February 2021 74 13Customs Tariff Vol 2 Sect XV 74 01-74 19
1 2A 2B 3 4 5 6 7
- - Plates:- consisting of at least one layer of fibreglass fabricimpregnated with epoxide resin,- covered on one or both sides with copper foil with a thicknessof not more than 0,15 mm,- with a dielectric constant (DK) of less than 5,4 at 1 MHz, asmeasured according to IPC-TM-650 2.5.5.2,- with a loss tangent of less than 0,035 at 1 MHz, as measuredaccording to IPC-TM-650 2.5.5.2,- with a comparative tracking index (CTI) of 600 or more
- - Plates or sheets:- with at least one layer of woven glass fibre, impregnated witha fire- retardant artificial or synthetic resin with a glasstransition temperature (Tg) of more than 130 °C as measuredaccording to IPC-TM-650, method 2.4.25,- coated on one or both sides with a copper film with athickness of not more than 3,2 mm,and containing at least one of the following:- poly(tetrafluoroethylene) (CAS RN 9002-84-0)- poly(oxy-(2,6-dimethyl)-1,4-phenylene) (CAS RN 25134-01-4)- epoxy resin having a thermal expansion of not more than10 ppm in length and width and not more than 25 ppm inheightfor use in the manufacture of circuit boards
27 February 2021 74 17Customs Tariff Vol 2 Sect XV 74 01-74 19
1 2A 2B 3 4 5 6 7
74 15NAILS, TACKS, DRAWING PINS, STAPLES (OTHER THANTHOSE OF HEADING 8305) AND SIMILAR ARTICLES, OFCOPPER OR OF IRON OR STEEL WITH HEADS OF COPPER;SCREWS, BOLTS, NUTS, SCREW HOOKS, RIVETS, COTTERS,COTTER PINS, WASHERS (INCLUDING SPRING WASHERS) ANDSIMILAR ARTICLES, OF COPPER
Nails and tacks, drawing pins, staples and similar articles 741510 00 00 S Kg Free AD-0 %, CA-0 %, CARIFORUM-0 %, CH-0 %, CI-0 %, CL-0 %,CM-0 %, CO-0 %, Central America-0 %, EC-0 %, EG-0 %,Eastern and Southern Africa States-0 %, European Union-0 %, FJ-0 %, FO-0 %, GE-0 %, GSP – Enhanced Framework-0 %, GSP – General Framework (Excluding IN)-0 %, GSP –Least Developed Countries-0 %, IL-0 %, IS-0 %, JP-0 %, KE-0 %, KR-0 %, LB-0 %, LI-0 %, MA-0 %, MD-0 %, MK-0 %, MX-0 %, NO-0 %, OCTs (Overseas Countries and Territories)-0%, PE-0 %, PG-0 %, PS-0 %, SADC EPA-0 %, SG-0 %, SM-0%, TN-0 %, TR-0 %, UA-0 %, UK-Canada agreement: re-imported goods-0 %[12], VN-0 %, WS-0 %, XC-0 %, XK-0 %,XL-0 %, ZA-0 %
74 18TABLE, KITCHEN OR OTHER HOUSEHOLD ARTICLES ANDPARTS THEREOF, OF COPPER; POT SCOURERS ANDSCOURING OR POLISHING PADS, GLOVES AND THE LIKE, OFCOPPER; SANITARY WARE AND PARTS THEREOF, OF COPPER
Table, kitchen or other household articles and partsthereof; pot scourers and scouring or polishing pads, glovesand the like
- Cooking or heating apparatus of a kind used for domesticpurposes, non-electric, and parts thereof
- - - - Disc (target) with deposition material, consisting ofmolybdenum silicide:- containing 1mg/kg or less of sodium and- mounted on a copper or aluminium support
( 1 ) TN701-According to the Council Regulation (EU) No 692/2014 (OJ L183, p. 9) it shall be prohibited to import into European Union goods originating in Crimea or Sevastopol.The prohibition shallnot apply in respect of: (a) the execution until 26 September 2014, of trade contracts concluded before 25 June 2014, or of ancillary contracts necessary for the execution of such contracts,provided that the natural or legal persons, entity or body seeking to perform the contract have notified, at least 10 working days in advance, the activity or transaction to the competentauthority of the Member State in which they are established. (b) goods originating in Crimea or Sevastopol which have been made available to the Ukrainian authorities for examination, forwhich compliance with the conditions conferring entitlement to preferential origin has been verified and for which a certificate of origin has been issued in accordance with Regulation (EU) No978/2012 and Regulation (EU) No 374/2014 or in accordance with the EU-Ukraine Association Agreement.
( 2 ) TN702-According to the Council Regulation (EU) No 1351/2014 (OJ L365, p. 46), the export of goods and technologies suited for use in the sectors of transport; telecommunications; energy;prospection, exploatation and production of oil, gas and mineral resources is prohibited:(a) to any natural or legal person, entity or body in Crimea or Sevastopol, or(b) for use in Crimea orSevastopol.The prohibitions shall be without prejudice to the execution until 21 March 2015 of an obligation arising from a contract concluded before 20 December 2014, or by ancillarycontracts necessary for the execution of such contracts, provided that the competent authority has been informed at least five working days in advance.When related to the use in Crimea orSevastopol, the prohibitions do not apply where there are no reasonable grounds to determine that the goods and technology or the services are to be used in Crimea or Sevastopol.
( 3 ) EX008-The export of arms and WMD-related items; Aviation fuels; Condensates and natural gas liquid; Curde oil; Helicopters and vessels; Industrial machinery, vehicles, iron, steel and othermetals; luxury goods; Refined petroleum products; gold and precious metals or diamonds to the Democratic People’s Republic of Korea is controlled (as well as related activities). Please referto the Sanctions to determine whether your items are controlled and whether you need a licence from the Export Control Joint Unit.
( 4 ) EX012-The export of energy-related goods for use in Russia and infrastructure-related goods and technology to Crimea is controlled (as well as related activities). Please refer to the Sanctionsto determine whether your items are controlled and whether you need a licence from the Export Control Joint Unit.
( 5 ) TN209-The export of nuclear and missile list items; graphite and relevant metals and other restricted goods to or for use in Iran may be controlled (as well as related activities). Please refer tothe Sanctions to determine whether your items are controlled and whether you need a licence from the Export Control Joint Unit.
( 6 ) EX010-The export of nuclear and missile list items; graphite and relevant metals and other restricted goods to or for use in Iran may be controlled (as well as related activities). Please refer tothe Sanctions to determine whether your items are controlled and whether you need a licence from the Export Control Joint Unit.
( 7 ) CD572-The wastes mentioned in Article 3 (1) of Regulation (EC) No 1013/2006 shall be subject to the procedure of prior written notification and consent.( 8 ) CD573-The wastes mentioned in Article 3 (2) of Regulation (EC) No 1013/2006 shall be subjected to the general information requirements laid down in Article 18 of the same Regulation, if the
amount of waste shipped exceeds 20 kg( 9 ) CD574-If the wastes listed in Annex III (green list) display certain hazardous characteristics, the relevant provisions shall apply as if these wastes had been listed in Annex IV (amber list). See
Article 3 (3) of Regulation (EC) No 1013/2006.( 10 ) CD577-The waste explicitly destined for laboratory analysis (Article 3 (4) of Regulation (EC) No 1013/2006) to assess either its physical or chemical characteristics or to determine its suitability
for recovery or disposal operations shall not be subject to the procedure of prior written notification and consent. Instead, the procedural requirements of general information requirementsshall apply (Article 18 of Regulation (EC) No 1013/2006). The amount of such waste exempted when explicitly destined for laboratory analysis shall be determined by the minimum quantityreasonably needed to adequately perform the analysis in each particular case, and shall not exceed 25 kg.
( 11 ) CD576-Exports from the Community of the wastes, listed in Article 36 of Regulation (EC) No 1013/2006, are prohibited if they are destined for recovery in countries to which the OECD Decisiondoes not apply (C(2001)107/Final of the OECD Council concerning the revision of Decision C(92)39/Final on control of transboundary movements of wastes destined for recovery operations).
( 12 ) CD727-Eligibility to benefit from this preference is subject to the presentation of an origin declaration stating the European Union origin of the goods, in the context of the Canada-EuropeanUnion Comprehensive Economic and Trade Agreement (CETA).
( 13 ) EU003-According to The Special Provisions of Section II (A) (3) of the Preliminary Provisions of the Combined Nomenclature the suspension of customs duties for goods for certain categories ofships, boats and other vessels and for drilling or production platforms shall be subject to conditions laid down in the relevant provisions of the European Union with a view to customs controlof the use of such goods.
27 February 2021 74 23Customs Tariff Vol 2 Sect XV 74 01-74 19
( 14 ) TM510-1. Customs duties shall be suspended in respect of goods intended for incorporation in the ships, boats or other vessels classified at the following CN codes 8901 10 10; 8901 20 10;8901 30 10; 8901 90 10; 8902 00 10; 8903 91 10; 8903 92 10; 8904 00 10; 8904 00 91; 8905 10 10; 8905 90 10; 8906 10 00; 8906 90 10 for the purposes of their construction, repair, maintenanceor conversion, and in respect of goods intended for fitting to or equipping such ships, boats or other vessels.2. Customs duties shall be suspended in respect of:(a) goods intended forincorporation in drilling or production platforms:(1) fixed, of subheading ex 8430 49, operating in or outside the territorial sea of Member States, or(2) floating or submersible, of subheading8905 20, for the purposes of their construction, repair, maintenance or conversion, and in respect of goods intended for equipping the said platforms.(b) tubes, pipes, cables and theirconnection pieces, linking these drilling or production platforms to the mainland.
( 15 ) CD333-The autonomous Common Customs Tariff duties laid down in Regulation (EEC) No 2658/87 for parts, components and other goods of a kind to be incorporated in or used for aircraftand parts thereof in the course of their manufacture, repair, maintenance, rebuilding, modification or conversion is suspended.In order to benefit from the suspension, the declarant shallpresent to the customs authorities an Authorised Release Certificate — EASA Form 1, as set out in Appendix I to Annex I to Regulation (EU) No 748/2012, or an equivalent certificate.Thecertificates which are deemed to be equivalent to Authorised Release Certificates are listed in Annex II to the Regulation (EU) 2018/1517.
( 16 ) TM861-This suspension does not apply to any mixtures, preparations or products made up of different components containing these products.( 17 ) EX005-The export of these items may be controlled under Retained Council Regulation (EC) No. 428/2009. Please refer to the Goods Checker to determine whether your items are controlled
and whether you need a licence from the Export Control Joint Unit.( 18 ) TN100-Entry under this subheading is subject to the conditions laid down in the relevant provisions of the European Union (see Article 254 of Regulation (EU) No 952/2013).( 19 ) TN207-The export of arms and WMD-related items; Aviation fuels; Condensates and natural gas liquid; Curde oil; Helicopters and vessels; Industrial machinery, vehicles, iron, steel and other
metals; luxury goods; Refined petroleum products; gold and precious metals or diamonds to the Democratic People’s Republic of Korea is controlled (as well as related activities). Please referto the Sanctions to determine whether your items are controlled and whether you need a licence from the Export Control Joint Unit.
( 20 ) EX001-The export of these items may be controlled under the Export Control Order 2008 as amended. Please refer to the Goods Checker to determine whether your items are controlled andwhether you need a licence from the Export Control Joint Unit.
27 February 2021 74 24Customs Tariff Vol 2 Sect XV 74 01-74 19
Chapter 74 Additional InformationProhibitions and Restrictions
Export Export control on restricted goods and technologies (717) B: Other certificates: Export authorisation for restricted goodsand technologies (C052)
B: Particular provisions: Goods for which a licence is notrequired (Y999)
C052Y999
27 February 2021 74 27Customs Tariff Vol 2 Sect XV 74 01-74 19
Export Export control on restricted goods and technologies (717) B: Other certificates: Export authorisation for restricted goodsand technologies (C052)
B: Particular provisions: Goods for which a licence is notrequired (Y999)
Import Import control - waste (755) E: Other certificates: Information document accompanyingshipments of waste as mentioned in Regulation (EC) No1013/2006 (OJ L 190) – Article 18 and Annex VII (C672)
E: Other certificates: Notification document as mentioned inRegulation (EC) No 1013/2006 (OJ L 190) - Article 4 and Annex IA(C669)
E: Particular provisions: Product not subjected to the provisionsof Regulation (EC) No 1013/2006 (OJ L 190) (Y923)
E: 20.00 kg
I: Other certificates: Information document accompanyingshipments of waste as mentioned in Regulation (EC) No1013/2006 (OJ L 190) – Article 18 and Annex VII (C672)
I: Other certificates: Movement document as mentioned inRegulation (EC) No 1013/2006 (OJ L 190) – Article 4 and Annex IB(C670)
I: Particular provisions: Product not subjected to the provisionsof Regulation (EC) No 1013/2006 (OJ L 190) (Y923)
I: 20.00 kg
C672C669Y923C672C670Y923
27 February 2021 74 28Customs Tariff Vol 2 Sect XV 74 01-74 19
Export Export control - Waste (751) E: Other certificates: Information document accompanyingshipments of waste as mentioned in Regulation (EC) No1013/2006 (OJ L 190) – Article 18 and Annex VII (C672)
E: Other certificates: Notification document as mentioned inRegulation (EC) No 1013/2006 (OJ L 190) - Article 4 and Annex IA(C669)
E: Particular provisions: Product not subjected to the provisionsof Regulation (EC) No 1013/2006 (OJ L 190) (Y923)
E: 20.00 kg
I: Other certificates: Information document accompanyingshipments of waste as mentioned in Regulation (EC) No1013/2006 (OJ L 190) – Article 18 and Annex VII (C672)
I: Other certificates: Movement document as mentioned inRegulation (EC) No 1013/2006 (OJ L 190) – Article 4 and Annex IB(C670)
I: Particular provisions: Product not subjected to the provisionsof Regulation (EC) No 1013/2006 (OJ L 190) (Y923)
![Journal J. Am. Ceram. Soc., [11] 2853–63 (1998)cuneyttas.com/cao-alo.pdfJournal J. Am. Ceram. Soc., 81 [11] 2853–63 (1998) 2853. has been proposed for this phase.21 Structural](https://static.documents.pub/doc/80x56/606d48784ae660127326ea6c/journal-j-am-ceram-soc-11-2853a63-1998-journal-j-am-ceram-soc-81.jpg)
