+ All Categories

Home > Documents > 740-0019 E-series pg1 0520Unload and make weapon safe. 6. Adjust windage and elevation so that the...

740-0019 E-series pg1 0520Unload and make weapon safe. 6. Adjust windage and elevation so that the...

Date post:	15-Jul-2020
Category:	Documents
Upload:	others
View:	0 times
Download:	0 times

Download Report this document

Share this document with a friend

Embed Size (px):

12

Transcript

Page 1: 740-0019 E-series pg1 0520Unload and make weapon safe. 6. Adjust windage and elevation so that the center point of laser coincides with groupings. To do this, adjust the laser toward

Page 2: 740-0019 E-series pg1 0520Unload and make weapon safe. 6. Adjust windage and elevation so that the center point of laser coincides with groupings. To do this, adjust the laser toward

��

Page 3: 740-0019 E-series pg1 0520Unload and make weapon safe. 6. Adjust windage and elevation so that the center point of laser coincides with groupings. To do this, adjust the laser toward

�� !��

Page 4: 740-0019 E-series pg1 0520Unload and make weapon safe. 6. Adjust windage and elevation so that the center point of laser coincides with groupings. To do this, adjust the laser toward

��

HOW TO ZERO YOUR VIRIDIAN® LASER1. Unload and make weapon safe.2. Set up a target with a clearly visible aiming point.WARNING: DO NOT ADJUST WINDAGE / ELEVATION BEFORE CONFIRMING POINT OF AIM THROUGH IRON SIGHTS. THIS UNIT IS SHIPPED FACTORY-SIGHTED.

3. Align Viridian laser to the iron sights of your firearm at the distance that you want to be your zero; between 21 feet

4. Load and fire a shot group at target using the laser to aim.5. Unload and make weapon safe.6. Adjust windage and elevation so that the center point of laser coincides with groupings. To do this, adjust the laser toward the grouping center using the chart below.

Up/Down Adjustments: Clockwise moves laser down. Counterclockwise moves laser up. Left/Right Adjustments: Clockwise moves laser right. Counterclockwise moves laser left.

Page 5: 740-0019 E-series pg1 0520Unload and make weapon safe. 6. Adjust windage and elevation so that the center point of laser coincides with groupings. To do this, adjust the laser toward

��

Page 6: 740-0019 E-series pg1 0520Unload and make weapon safe. 6. Adjust windage and elevation so that the center point of laser coincides with groupings. To do this, adjust the laser toward

��

��® WARNING LABEL

510-532nm

Page 7: 740-0019 E-series pg1 0520Unload and make weapon safe. 6. Adjust windage and elevation so that the center point of laser coincides with groupings. To do this, adjust the laser toward

Page 8: 740-0019 E-series pg1 0520Unload and make weapon safe. 6. Adjust windage and elevation so that the center point of laser coincides with groupings. To do this, adjust the laser toward

��

Page 9: 740-0019 E-series pg1 0520Unload and make weapon safe. 6. Adjust windage and elevation so that the center point of laser coincides with groupings. To do this, adjust the laser toward

�� ®�� ®�� !�� "��"�� #�� $��%&''()$��"��

Page 10: 740-0019 E-series pg1 0520Unload and make weapon safe. 6. Adjust windage and elevation so that the center point of laser coincides with groupings. To do this, adjust the laser toward

Page 11: 740-0019 E-series pg1 0520Unload and make weapon safe. 6. Adjust windage and elevation so that the center point of laser coincides with groupings. To do this, adjust the laser toward

Page 12: 740-0019 E-series pg1 0520Unload and make weapon safe. 6. Adjust windage and elevation so that the center point of laser coincides with groupings. To do this, adjust the laser toward

Check out our full line of high tech weapon-mounted accessories and precision optics at ViridianWeaponTech.com

TAKE ALOOK

Recommended

IN UT Requires 2xAAA Batteries (Not supplied) - Trackace User Manual.pdf · 4 1e 1d Stage 1 (continued) Turn the laser unit on and adjust the angle and level of the laser beam until

INSTRUCTION MANUAL MANUALE DI ISTRUZIONI ......5 The elevation and windage adjustments are shown in Figure 3. For both elevation and windage, each click will change the bullet’s

Laser Pointer Mouse - MITweb.mit.edu/6.111/www/s2006/PROJECT/3/Project3.pdfpointer and can adjust various parameters that define how the laser is found. Figure 1 presents an overall

Auto-Levelling Rotary Laser Level F · Auto-Levelling / Manual Slope Mode Key Scan, Spot, Slope and Calibration Adjust Keys LEDs Power LED - Blinking GREEN • Laser Tool is Auto-Levelling

PREDICTION OF WINDAGE LOSS IN - NASA · Windage loss in a generator is the power absorbed by the fluid surrounding the rotor as a result of the relative motion between the rotor and

Nbsbulletinv10n2p191 A2b Trubine Windage Loss

€¦ · relocate existing sign cap existing irrigation line at adjust manhole frame and cover adjust cleanout casting adjust water valve box adjust blow-off lid replace/adjust to

Adjust After the Pour Adjust Aft - southernpipe.com

Adjust everywhere

Elevation Adjustment Knob · Elevation Knob Windage Knob Windage and eleVaTion adjuSTmenTS Vortex Viper PST riflescopes incorporate precision finger adjustable elevation and windage

SURE-LOC ICONX INSTRUCTIONS - FeraDyne · Windage Tensioning System The Windage Tensioning System of the ICONX uses four screws to increase/decrease the amount of tension in the Windage

· Web viewPlease do not adjust margins. Please do not adjust margins. ARTICLEJournal Name. Please do not adjust margins. Please do not adjust margins. Please do not adjust margins

Scope Owner’s Manual...AZTEC Optics Emerald Series Owner’s Manual Fire another shot, look at where the shot hit, and adjust the elevation and windage knobs accordingly. Make small

WINDAGE POWER LOSS IN SPUR GEAR SETS - WSEAS · WINDAGE POWER LOSS IN SPUR GEAR SETS ... geometry of the spur gear using the commercial Computational Fluid Dynamics ... It is assumed

Adjust, Void, & Resubmit Claim - Washington · Adjust, Void, & Resubmit Claim (Mar 5, 2015) 7 of 30 Adjust Paid Claim 8. The Adjust Social Service Claim page appears 8 Adjust Social

Windage resistance of steam-turbine wheels BtUletinoftheBureauofStandards [Voi.io specifiedbythevaluesoftheratiosofanumberoflengthsto someonelength,suchasthediameterofthewheel.Itistobe

USMC Windage Calculation