81969593 How to Guide JTAG Repair All in One Guide for Dreambox Dm500S UKCS UK Cable Satellite

7/18/2019 81969593 How to Guide JTAG Repair All in One Guide for Dreambox Dm500S UKCS UK Cable Satellite

http://slidepdf.com/reader/full/81969593-how-to-guide-jtag-repair-all-in-one-guide-for-dreambox-dm500s-ukcs 1/9

UKCS – UK Cable & Satellite

...UK Cable & Satellite News,Technology,Information & repair guides.

Home

About

« How to guide: OpenBox S9 HD as a card server

How to guide: Upgrade, flash, change the firmware image on the OpenBox S10 via USB »

How to guide: JTAG repair all in one guide for DreamboxDm500S

Written by DrF on June 18th, 2011

A guide showing how to JTAG repair a bricked, broken, bad flash, corrupt firmware image on a Dreambox DM500S receiver.

Useful when all else has failed.

JTAG DM500s AiO Repair

5 resistors of 100 Ohms at 2,3.4.5 and 11 pin 25 pin male connector

These labels are 1,2,4,5,6 tags that go on board Dream, you do not revolt it is not correct labels soldering those points, but my

own label as indicated in Fig.

Servidor Cloud 50% OFF A Under enloqueceu. Todos seus planos de Cloud com 50% desconto! Under.com.br/Cloud

Directional couplers Directional couplers, Duplexers Bandpass, power dividers, RF filter www.amcrf.com

Serial Port Monitor Monitor log and analyze Serial Port data with software Serial Monitor hhdsoftware.com

w to guide: JTAG repair all in one guide for Dreambox Dm500S | ... http://starview-6.info/2011/06/18/how-to-guide-jtag-repair-all-in-one-g...

9 2/17/2012 3:12 PM



On the other side to connect a 15-25 and this wire goes to the board Dream at no. 16 or to ground.

And it goes as indicated in figure, with very short holding soldering iron at these points because it is very easy to know how

to come off, and then you will need to solder the SMD resistors, so that it does not keep as short soldering iron.

When it all together, connect the 25 pin male connector on the extension serial cable 25pin / 25 pin m / f to the PC LPT port,

you can now include the power to dream. If the Chinese copy of your Dream suffered from the “bomb” then you will Shine

on Dream no LEDs.


9 2/17/2012 3:12 PM



This procedure requires repeated switching on and off the receiver dream to revive the process started, it is enough to click

on the info.bat to verify that the tuner is working and what is the MAC address in the “dead” dream, and it will be written:

As can be seen in it is the correct MAC address DreamMultimedije 00 09 34 01 a4 3f, it is because this process has been

revived, and this is just repeated that it could be PrintScreen-at

After pressing any key, the screen disappears, and now you can run write flash, then click on 2alps.bat:

Flash-Gel takes about 2 min. and it shows you the percentage. This file is 2alps.bat

MAC address 00 09 34 01 4d 1f, it can at will change if you rename the file 2alps.bat 2alps.txt and open it with ultra editor,

change the MAC address, and only the second half, as it must be among the first DMM 00 09 34 the other half can be anycombination of 0-9 and AF. To save and then rename again to 2alps.bat. This change does not have to work unless you have

a local area network 2 Dream with the same MAC address, then one needs to address in this way to edit.

After 100% you get this message:

Btw, if you have an older copy of the Chinese Dream with Philips tuner, which you showed info.bat

Then you use 3philips.bat

After this, turn the power off, unplug the JTAG, turn the power back, and your dream is alive everything in it is left as it was

before the bomb.

Now is your DM500 DMM’s MAC address and do not have to be afraid any bombs because the U.S.

as the original.

The files :

JTAG_DM500_AiO_Repair


9 2/17/2012 3:12 PM



Mirror :

http://www.herosh.com/download/8895015/JTAG_DM500_AiO_Repair.rar.html

Posted in Dreambox (cable & satellite) |

Tags: bad flash, corrupt, damaged, Dm500C, DM500S, dreambox, factory reset, firmware image, guide, jtag, repair, restore

15 Comments so far ↓

bouni says:

September 3, 2011 at 9:02 am

salut .

j’ai besoin de jtag pour demo dreambox dm500s

jtag dm500s

1.

DrF says:

September 3, 2011 at 9:11 am

Translation : hello. “I need to jtag jtag demo Dreambox DM500 DM500S”

How to guide: JTAG repair all in one guide for Dreambox Dm500S http://starview-6.info/?p=992

How to Jtag repair Dreambox DM500s Satellite receiver (video) http://starview-6.info/?p=260

2.

vijai says:

October 24, 2011 at 9:49 pm

need try this

3.

vijai says:

October 24, 2011 at 9:52 pm

I need Jtag dreambox 500

4.

DrF says:

October 24, 2011 at 10:22 pm

The how to guide and I think we have videos on how to make the JTAG cable up for the DM500s and its clones.

Here is the video guide :

How to Jtag repair Dreambox DM500s Satellite receiver (video)

http://starview-6.info/?p=260

5.

abs says:

November 23, 2011 at 10:10 pm

Hi, is there a way to jtag and read the root password or reset it?

Thanks

6.

DrF says:7.


9 2/17/2012 3:12 PM



November 23, 2011 at 10:22 pm

If you was Jtagging the DM500S you would end up reflashing putting another image on the box.

If you want to just recover or reset the password see these :

Tool: Windows Utility to remove all Dreambox passwords


How to: Delete password from Dreambox using TuxBox Commander


How to guide: Changing a Dreamboxs password using DreamBox Control Center (DCC)


How to guide: Reseting Dreambox Root password


How to guide: Change the password on the Dreambox receiver.


How to reset your Dreambox password using remote control


Guide : Remove the password from Dreambox,with tuxbox Commander


How to reset DreamBox password


Theres a few more around the site, check the Dreambox section might be some of use in there, or clones like the

EagleBox im sure we had guides for that too in the same password situation

onepic says:

December 21, 2011 at 8:23 pm

Is it possible to write the full image whith JTAG ? I have flashed the bootloader OK (green light on after the procedure)

on my DM500S clone but the serial port is unaccesible with dreamup (all verssions) or with Hyperterminal. I replaced

also the MAX3243 but the same. Thank you !

8.

DrF says:

December 22, 2011 at 11:25 am

Usually its easiest to flash a complete image via JTAG as that puts the Dreambox back into its factory firmware

working state. However since you seem to only have the bootloader working you could try this guide to force a flash

over network.

How to guide: Flashing a Dreambox DM500S or DM600 in less than 2 mins


9.

basharat ali says:

January 1, 2012 at 7:27 pm

i have dream dm 500s and it is not conect by rs232 now my dreambox is dead plz help me.

10.

DrF says:

January 1, 2012 at 9:01 pm

You could try as mentioned above your post, or you will be forced to do a full JTAG image recovery I think.

11.

Jahn says:

January 13, 2012 at 7:17 am

12.


9 2/17/2012 3:12 PM



Is there available SOURCE code of the jtag software for DM500 flashing?

(Not only compiled source)

Thanks

DrF says:

January 13, 2012 at 8:49 am

Not that I know off, there are many open source applications that can be used to flash the DM500s I am pretty sure

some of them would come with there source, what is it you are looking for? just how they work? or whats in there?

What about taking it apart with something like IDAPro?

13.

Jahn says:

January 13, 2012 at 10:00 am

Yes, I would like to modify it.

Do you have any link to such source?

Thanks

14.

DrF says:January 13, 2012 at 11:57 am

That’s quite interesting, I do not have the source to this app. I’m sure some more generic flash/jtag apps would come

with there source there’s quite a few of them available for Linux/Windows. Part of the prob I think is people have

made the app for a certain box or task and made it easy for everyone to use, hence no instructions, source code or any

other help

15.

Leave a Comment

Name *

Email (will not be published) *

Website

Comment

CAPTCHA Code *


9 2/17/2012 3:12 PM



SystemSat 80cmMOTORISED S…

Systemsat

£99.95

Highlight USB

25pin/9pin to …

MTD

£2.97

Dream-Multimedia-TV …

Dream Multimedia

£56.99

F-CONNECTOR

TOOL

Various

£4.95

Satgear Sky/Freesat- …

Satgear

£27.95

Konig SatelliteF-Splitter

Konig

£1.70

Openbox S10 HDPVR Satellite R…

Senua

£69.99

Get Widget Privacy

Search site :

Translator

Sale Items :


9 2/17/2012 3:12 PM



Categories

Atmega

AzBox

CCCam

Dbox

Dreambox (cable & satellite)

Eagle Box

EuroVox Guides & Turorial

Freesat

FTA101FunCard Series Smartcards

Gallery of cable boxs (Eurovox,Starview,Kryptview etc.)

General Cable

HD & Premium)

Kryptview Cable Boxs

Networking

Openbox

OsCam

Satellite Receiver manuals

SKY (BSKYB)

Spiderbox series

Starview Fixes & FirmwareStarview Guides & Tutorials

Technomate Satellite Receivers

UKCS Privacy Policy

Uncategorized

VirginMedia

Vu+

Tags :

3pm football alsat astra AzBox card share cardshare cardsharing card sharing cccam cline cs dm500

DM500S dm600 dm600PVR dm800 dm800hd dreambox Dream Multimedia firmware flash Freesat

gift guide hotbird how to image linux manual network newcamd openbox oscam repair satellite satellite receiver server

setup setup guide sky spiderbox technomate tutorial uk vu+

Dream-Multimedia-TVDreamBox DM-500S...

Dream Multimedia

Best Price £56.99or Buy New

Privacy Information

Dreambox DM 500S 500C500T Remote Co...

Dreambox

Best Price £1.99or Buy New £2.75

Privacy Information

Blogroll

Busydizzys

Dreambox Help

Dreambox Sales

Rockadolli

Rockadolli on Etsy

TecnicNews


9 2/17/2012 3:12 PM



Last searched terms

- difference betw(...)ginal and clone

- firmware openbox s10 hd pvr- satilite channel uk sky share

- gemini+firmware+dm500

- matrix cam air wifi cccam

Last referers

- www.google.com/(...)ntpklDArDVNPg-Q

Visitors Online Now

04 visitor(s) onlinepowered by WassUp

© 2012 UKCS – UK Cable & Satellite | A WPHackr Experience


Date post:	02-Mar-2016
Category:	Documents
Upload:	sinharayanun-sinyamimwaunun
View:	365 times
Download:	2 times

81969593 How to Guide JTAG Repair All in One Guide for Dreambox Dm500S UKCS UK Cable Satellite

Documents