+ All Categories
Home > Documents > 89328128 Usb Mp3 Player Connection Diagram

89328128 Usb Mp3 Player Connection Diagram

Date post: 16-Apr-2015
Category:
Upload: prakash-baria
View: 152 times
Download: 9 times
Share this document with a friend
12
USB MP3 Player Guide From www.TechFeb.com Requirement components and parts for create USB Mp3 Player at home 1. Usb Mp3 Module with Remote (See screenshot) 2. IR Sensor with Metal case (You can buy it from any TV spare parts shop) 3. 0-9 AC to Dc( 1 Amp.) Transformer (You can buy it from any TV spare parts shop) 4. Audio Board 6 Volt to 9 Volt (You can buy it from any TV spare parts shop) 5. IC 7805 with 1000MFD 16 to 25 volt Capacitor (You can buy it from any Tv spare parts shop)* * IC 7805 is used for convert 9 volt in 5 volt that is require for Usb Mp3 Module and your audio board require 6 volt to 9 volt so there is no need to connect Your audio board to 5 volt supply only 5 Volt is only for Module circuit. 6. IN 4007 Diodes(4) for filter 0-9 power supply 7. One blank project matrix PCB Board for mount IC 7805 Power Supply and other components on it. 8. One USB socket for connect Pen Drive (Usb) to module 9. One Audio Jack with pin for connect speaker to you audio board 10. One Volume control (10 K) for control audio output
Transcript
Page 1: 89328128 Usb Mp3 Player Connection Diagram

USB MP3 Player Guide From www.TechFeb.com

Requirement components and parts for create USB Mp3 Player at home

1. Usb Mp3 Module with Remote (See screenshot)

2. IR Sensor with Metal case (You can buy it from any TV spare parts shop)

3. 0-9 AC to Dc( 1 Amp.) Transformer (You can buy it from any TV spare parts shop)

4. Audio Board 6 Volt to 9 Volt (You can buy it from any TV spare parts shop)

5. IC 7805 with 1000MFD 16 to 25 volt Capacitor (You can buy it from any Tv spare parts

shop)*

* IC 7805 is used for convert 9 volt in 5 volt that is require for Usb Mp3 Module and your

audio board require 6 volt to 9 volt so there is no need to connect Your audio board to 5 volt

supply only 5 Volt is only for Module circuit.

6. IN 4007 Diodes(4) for filter 0-9 power supply

7. One blank project matrix PCB Board for mount IC 7805 Power Supply and other components

on it.

8. One USB socket for connect Pen Drive (Usb) to module

9. One Audio Jack with pin for connect speaker to you audio board

10. One Volume control (10 K) for control audio output

Page 2: 89328128 Usb Mp3 Player Connection Diagram

Circuit Module and It’s Remote Control

The main attraction is its cost. The board cost only 120 Rupees( 3$) with all 3 Connectors.

Audio Board Rs. 40 Only.

Transformer (0-9) 1 Amp.Rs. 40 Only.

IR Sensor, IC7805, Capacitor (1000MFD 16 to 25 volt-2) and IN 4007 (4 Diodes) Rs. 20 Only.

Page 3: 89328128 Usb Mp3 Player Connection Diagram

The board circuit diagram is so simple that there are a very few connections. Some of the

connections are:-

Connector-1 3.3V - Power for IR sensor (Same as in Picture-3)

IR - IR data line of IR sensor

GND - Ground of IR sensor

PLAY - switch connection for play

VOL- - switch connection for vol -

PMCH - switch connection for mode(Radio/USB)

VOL+ - switch connection for vol +

R - Right channel output to audio amp

GND - ground

L - Left channel output to audio amp

Connector-2 GND - USB Ground

DP - USB DATA +

DM - USB DATA -

5V - USB 5V

Connector-3 (For SD card connection)

Ifyou have plan for use only Pen Drive for songs then there are no requirement for

Connector-3.You can use your Memory Card using Memory card reader and insert it in

USB port.

CS

DATA

CMD

CLK

DET

3.3V

The other main features are an built in FM receiver and you can also control FM with remote

control User Friendly Auto Search & Save Station Operation Available. The player can read up

to 1999 songs.

Page 4: 89328128 Usb Mp3 Player Connection Diagram

PRODUCT INFORMATION OF Vire (http://www.vire.net.cn) USB MP3 player board:

A) Play the FM channels

B) Display The Song Number

C) Numerical Key Input Operation for Song Selection.

D) FM Radio : 87.5 ¨C 108.0 MHz

E) Auto Radio Station Search Operation.

F) User Friendly Auto Search & Save Station Operation Available.

G) Numerical Display For Volume.

H) 188.8 LED Module Display.

I) Rotated Volume Control Key could be connected

i) 4/6 Keys On Product

ii) Select Forward

iii) Select Backward

iv) Volume Up

v) Volume Down

First you need 5 Volt and 9 Volt Power Supply. Here is complete diagram of IC 7805 5 Volt

Power Supply for Usb Mp3 Module Circuit.

If you are using any external Amplifier or Computer Speaker then you can use 5 Volt

Mobile charger as power supply for Usb Mp3 module. But be careful when connects charge

pins make sure + and – pins have in right way otherwise board may be damage.

Page 5: 89328128 Usb Mp3 Player Connection Diagram

Circuit Diagram of 7805 5 Volt Power Supply for 0-9

The +5 volt power supply is based on the commercial 7805 voltage regulator IC. This IC

contains all the circuitry needed to accept any input voltage from 8 to 18 volts and produce a

steady +5 volt output, accurate to within 5% (0.25 volt). It also contains current-limiting circuitry

and thermal overload protection, so that the IC won't be damaged in case of excessive load

current; it will reduce its output voltage instead.

The 1000µf electrolytic capacitor serves as a "reservoir" which maintains a reasonable input

voltage to the 7805 throughout the entire cycle of the ac line voltage. The four rectifier diodes

keep recharging the reservoir capacitor on alternate half-cycles of the line voltage, and the

capacitor is quite capable of sustaining any reasonable load in between charging pulses.

Page 6: 89328128 Usb Mp3 Player Connection Diagram

Detail of IR Sensor used in Mp3 Player for Remote Control

Full Name – IR Sensor Receiver with Metal case

Note:-Please use same Sensor with Metal case for Mp3 player.

Notes.

Use 1st pin as IR or RI Signal .

Use 2nd

pin as GND(-).

3rd

pin to 3.3 Volt from Usb mp3 player module or circuit.

Page 7: 89328128 Usb Mp3 Player Connection Diagram

Complete Connection Diagram of Usb Mp3 Player Circuit Module with all Pin Details

Here you can see TackTileButtons connection in picture if you are using Remote control only then there

are no need any connection for buttons because all control like volume up down Next Previous control

with Remote easily. I publish these buttons connection only for knowledge view.

Note:- In picture you can see starting pins ( L G R). These pins are for Left Audio, Ground and Right

Audio. If you have plan for use same power supply in both Audio Board and This mp3 player circuit then

don’t connect pin G (Ground) to any point otherwise output sound may be not clear. Use Both L and G

(Gnd) if you are using outside Audio system Like computer Speaker or any Amplifier device. Computer

speakers pin have three points so you can use all three points (L, G and R). See Picture

Page 8: 89328128 Usb Mp3 Player Connection Diagram

6 watt 9 to 12 Volt Audio Amplifier circuit diagram for Mp3 player using TA7222A IC

Here is complete easy to understand amplifier circuit for create external audio amplifier with good

quality sounds. You can use Mp3 player Module circuit audio output as input in this circuit.

More Description:

Here is the circuit diagram of a 6W amplifier using the TA7222AP from Toshiba.TA7222AP is an excellent

integrated audio amplifier which can deliver 5.8W to a 4 Ohms load at 12V supply voltage. The IC has

very good features like, muting function, low distortion, high ripple rejection, short circuit protection,

thermal shut down etc. This amplifier can be operated from 9 to 12V and this makes it ideal for car radio

mp3 playersapplications.

Notes.

The circuit can be assembled on a Vero board.

Use 12V DC for powering the circuit.

The IC must be heatsinked.

Speaker can be a 4 ohms one.

For optimum performance input and output must be separately grounded.

Page 9: 89328128 Usb Mp3 Player Connection Diagram

5W 9-12V Audio Amplifier Kit using TBA810 Audio IC

Product Description

Supply voltage: 12 to 16V DC / 0.5A

Based on the TBA810 Integrated Circuit

Input sensitivity: 100mV / 47K Ohm

Output power: 7W Max. / 4 Ohm

Frequency response: 40Hz to 18KHz (-3dB)

Includes volume control

PC board dimensions: 1.75" x 2.25"

This circuit is a compact design AF amplifier based on the TBA810 Integrated Circuit. Its low

consumption and compact dimensions make it ideal for all kinds of audio amplification

applications. The circuit incorporates an overload protection circuit and volume control. In

addition, the circuit has low/high impedance inputs which can be connected to any audio source. You can buy it from any Electronics shops in just Rs. 30-40 only.

Page 10: 89328128 Usb Mp3 Player Connection Diagram

Screenshot of Ready to use Usb mp3 player in Plastic Box

Page 11: 89328128 Usb Mp3 Player Connection Diagram

ASSEMBLING OF FM PLAYER WITH USB

(PENDRIVE)

Page 12: 89328128 Usb Mp3 Player Connection Diagram

Mp3 Player in small plastic box.

Now You have complete information on “ How to Make Usb Mp3 Player at home


Recommended