DSA-300E8CH Digital SR Amplifier

Digital Amplifier Maximum of 300W×8CHAll new DSA-300E is a multi-channel power amplifi er of 300 W×8CH(4 Ω)/150 W×8CH(8 Ω) or high output of 600 W×4CH(8 Ω) when used in Bridge mode. It is particularly suitable for venues that require high-quality BGM such as restaurant, hotel and conference centers. You can build a much more cost and space-efficient system as compare to previous 8CH analog amplifiers as it is lightweight and low heat. 2 U-sized.

Simultaneous BroadcastThis amp is ideal for a diffusion coupled with a matrix upstream for example or with different sources for each channel.

DIGITAL

DSA-300E Digital Amplifier 8×300W = 2U

ANALOG

8 Analog Amplifiers 240W = 8x3U

x8 <

CD Player

CD Player

MIC

Traditional amplifier

DSA-300E

IN

IN 1

IN 8 OUT 8

CD Music

CD Music

MIC

ExhibitionHall A

ExhibitionHall A

ExhibitionHall B

OUT

OUT 1

ACT/STBY LED Display

AC Power Input Termina Ventilation Hole XLR Input Speakon Output Terminal

Bridge Mode LED Ventilation Hole

Sound Displayed LED (Level, Clip, Protection)

Volume Control Power Switch

1

1

1

1 2 3 4

3 5

2

2

2 4 6

3

3

4

4

5

6

Panels front/rear

Maximum of 600W Output per Channel in Bridge Mode Bridge mode enables two connected channels to be one output. If every channel is on Bridge mode, maximum of 600 W×4CH(8 Ω) is available. Place “MODE SWITCH” on the rear panel to “BRIDGED”and Bridge mode LED on the front panel lights up. Connect two adjacent even and odd channels to use Bridge mode. CH 1-CH 2 / CH 3-CH 4 / CH 5-CH 6 / CH 7-CH 8. Insert audio signal to odd channel.

LED Indicators The backlit LEDs enable to monitor AC/DC power, STBY status, SIG -30dB output level of each channel, Clip and Protect status.

High-quality Sound of High S/N and Low THD DSA-300E is a high-quality pro audio power amplifier with S/N over 100dB and THD below 0.1 %. It perfectly suits for hotels’, conference centers’ and restaurants’ the venues in need of supreme quality BGM play.

5 6 , c h e m i n d e l a Fl a m b è re · 3 1 3 0 0 To u l o u s e · F R A N C E · T é l . 3 3 ( 0 ) 5 6 1 3 1 8 6 8 7F a x 3 3 ( 0 ) 5 6 1 3 1 8 7 7 3 · c o m m e r c i a l @ m a j o r c o m . f r · w w w . m a j o r c o m . f r ©

Maj

orco

m 0

5/20

17 -

Maq

uett

e L.

Coh

en n

ko2@

sfr.f

r

Technical specifications

PA EXAMPLE

Model DSA-300E

Rated power (stereo)8Ω per channel 150W

4Ω per channel 300W

Rated power (bridged) 8Ω per channel 600W

Input sensitivity 1.23V RMS (4dBu)

Voltage gainStereo 29dB

Bridged 35dB

THD (ASE17, 1/3 power) < 0.3% (20kHz LPF)

S/N (20 kHz LPF) > 100dB (20kHz LPF)

Frequency response (1W, ±3dB) 20Hz ~ 20kHz

Output circuit Class D

Input impedance 10kΩ balanced

LED Indicators SIG, CLIP, PROT, Bridge

Safety circuit Full short circuit, thermal protection, Power on/off muting, DC output protection

Input connector XLR female

Output connector 4 pole speaker socket

Operating temperature -10°C~+40°C

Power source AC 220-240V, 50/60 Hz

Power consumption 480W (1/8W)

Dimensions (WxHxD) 482 × 88 × 367 mm

Weight (kg) 7.7

MX-1243(Mixer)

DEQ 2496 (Sound Processor)

DSA-300E(Amplifier)

SQ-10T

SQ-10T

CD-6208 (Player)

Bridged 600W Bridged 600W

STAGE

Audio [Mic/Line]

Audio [(Low/High-Z]