Date post: | 07-Apr-2018 |
Category: |
Documents |
Upload: | barry-seymour |
View: | 231 times |
Download: | 0 times |
of 26
8/4/2019 9840 IP Dome Mount Installation Manual
1/26
DVTel IP Dome Mounting Instructions
- 1 -
Dome Mounting
This installation manual suits for all DVTel dome models. The focus of this manual is the mechanical installation.
For IP configuration or dome programming, consult the appropriate dome manuals.
1 In-ceiling Mounting [For indoor mounting only]1.1 In-ceiling Mounting Specifications
Below figures demonstrate the installation specifications for in-ceiling mounting.
Ceiling
Scaleboard
R7685
198
150
170O
210O
Theinceilingspace
mustbe
morethan150mmh
igh.
15~55mm
1.2 Installation Procedures For In-ceiling Mounting
Easily install your DVTel IP Dome in below 8 steps:
1. Locate the center point of a suitable mounting location, and draw a circle with 199+3mm in diameter on
the ceiling. (If it is necessary, add a same material scale board to the ceiling, so that the dome can be
mounted steadily to the ceiling.)
R99.5+1.5
Add a scaleboard
Figure 1-1. Drawing a circle on the ceiling
8/4/2019 9840 IP Dome Mount Installation Manual
2/26
DVTel IP Dome Mounting Instructions
- 2 -
1. Use a cutting tool suitable for the material of the ceiling, and cut the circle out of the ceiling.
Figure 1-2. Cutting the Circle out of the Ceiling
2. Take out the upper housing from the dome package. Loosen the bolt that holds the connection circuit board,
and lift the board to make an opening for wiring.
Figure 1-3. Preparing the housing
3. Pull the power and Cat-5 cables through the wiring conduit into the housing. Then, compress the spring
mounting clips on the housing, and push it through the mounting hole. Tighten the screws until the housing
is secured on the ceiling.
Figure 1-4. Installing Housing
8/4/2019 9840 IP Dome Mount Installation Manual
3/26
DVTel IP Dome Mounting Instructions
- 3 -
4. Take out the dome drive from the dome package. If necessary, set the camera ID by configuring the DIP
switch S1 (see Figure 1-5). For details on how to configure the DIP switch, please refer toAppendix I. Most
installation will use the default settings.
S1
Figure 1-5. DIP Switch S1
6. Line up the two taps located on the upper side of the dome drive with the corresponding grooves in the
housing. Insert both tabs into the grooves. Push up the dome insert until both tabs click into place. Be sure that
you hear two clicks.
Tab
Figure 1-6. Installing Dome Drive
7. Take out the lower housing from the dome package. Line the lock mark on the lower housing pastern ringer up
with the screw on the dome drive. Then facing the dome drive, turn the lower housing clockwise to fit it firmly
with the black cover.
Figure 1-7. Installing Dome Bubble
8/4/2019 9840 IP Dome Mount Installation Manual
4/26
DVTel IP Dome Mounting Instructions
- 4 -
8. Turn on the power. The dome will pan, tilt, and zoom to initiate system parameters as well as to verify
the normal operation of the dome drive.
After the initiation sequence, the dome will stop and be ready for programming and operation.
2 Over-roof Mounting [For outdoor mounting only]2.1 Over-roof Mounting Specifications
Below figure demonstrates the over-roof mounting specifications:
300
1100
160
330
R7670
2
45
150
162
265
240O
218O
8/4/2019 9840 IP Dome Mount Installation Manual
5/26
DVTel IP Dome Mounting Instructions
- 5 -
2.2 Installation Procedures For Over-roof Mounting
Easily install your DVTel IP Dome in below 7 steps:
1) Place and secure the bracket base at a suitable position against the wall. Pull the power and Cat-5 cables
through the bracket and the sustaining pipe.
Figure 2-1-1. Install Bracket Base
Bracket base dimensions:
Figure 2-1-2. Over-roof Installing Bracket Base Dimensions
8/4/2019 9840 IP Dome Mount Installation Manual
6/26
DVTel IP Dome Mounting Instructions
- 6 -
2) Take out the upper housing from the dome package. Loosen the bolt that holds the connection circuit board,
and lift the board to make an opening for wiring.
Figure 2-2. Lifting Connection Board
3) Pull the cables through the opening, and then screw the upper housing onto the mount bracket. For outdoor
housing, it is recommended to apply thread compound to the threads on the housing.Secure the connection
with a holding screw.
Figure 2-3. Installing Housing
4) Take out the dome drive from the dome package. If necessary, set the camera ID by configuring the DIP
switch S1 (see Figure 2-4). For details on how to configure the DIP switch, please refer toAppendix I. Most
installation will use the default settings.
5)
S1
Figure 2-4. DIP Switch S1
8/4/2019 9840 IP Dome Mount Installation Manual
7/26
DVTel IP Dome Mounting Instructions
- 7 -
5) Line up the two taps located on the upper side of the dome drive with the corresponding grooves in the
housing. Insert both tabs into the grooves. Push up the dome insert until both tabs click into place. Be sure that
you hear two clicks.
Tab
Figure 2-5. Installing Dome Drive
6) Take out the lower housing from the dome package. Line up the screw holes of the lower housing with
corresponding holes on the housing, and then secure the cover with supplied pan head screws.
Figure 2-6. Installing Dome Bubble
7) Turn on the power. The dome will pan, tilt, and zoom to initiate system parameters as well as to verify the
normal operation of the dome drive.
After the initiation sequence, the dome will stop and be ready for programming and operation.
8/4/2019 9840 IP Dome Mount Installation Manual
8/26
DVTel IP Dome Mounting Instructions
- 8 -
3 Wall Mounting [For both indoor and outdoor mounting]3.1 Specifications For Short-Arm Wall mounting
Below figures demonstrate the installation specifications for short-arm wall mounting.
Indoor Mounting:
310
8
240275
225
140
70
R76
218O
154O
O8
140
160
11085
Outdoor Mounting:
310
275
8
1621
50
245
70
240
R76
240O
218O
O8
85110
160
140
8/4/2019 9840 IP Dome Mount Installation Manual
9/26
DVTel IP Dome Mounting Instructions
- 9 -
3.2 Specifications For Long-Arm Wall MountingBelow figures demonstrate the installation specifications for long-arm wall mounting.
Indoor Mounting:
O8
140
160
11085
316.5
140
70
457O
154O
457422
8
225
R76
Outdoor Mounting:
457422
8
316.5
245
162150
240O218O
70
R76
O8
140
160
11085
3.3 Installation Procedures For Wall Mounting
Easily install your DVTel IP Dome in below 7 steps:
1). Install the wall mount at a suitable location, and pull the power and Cat-5 cables through the mount.
Figure 3-1-1. Installing Wall Mount
8/4/2019 9840 IP Dome Mount Installation Manual
10/26
DVTel IP Dome Mounting Instructions
- 10 -
For dimensional diagram of the mount, please refer to the following figure.
Figure 3-1-2. Dimensional Diagram for Wall Mount
2). Take out the upper housing from the dome package. Loosen the bolt that holds the connection circuit board,
and lift the board to make an opening for wiring.
Figure 3-2. Lifting Connection Board
3). Pull the cables through the opening, and then screw the upper housing onto the wall mount. For outdoor
housing, it is recommended to apply thread compound to the threads on the housing. Secure the connection with
a holding screw.
Holding Screw
Figure 3-3. Installing Housing
O8
140
160
85
422457
NPT G1' '
8/4/2019 9840 IP Dome Mount Installation Manual
11/26
DVTel IP Dome Mounting Instructions
- 11 -
5. 4). Take out the dome drive from the dome package. If necessary, set the camera ID by configuring the
DIP switch S1 (see Figure 3-4). For details on how to configure the DIP switch, please refer to Appendix I.
Most installation will use the default settings.
S1
Figure 3-4. DIP Switch S1
5). Line up the two taps located on the upper side of the dome drive with the corresponding grooves in the
housing. Insert both tabs into the grooves. Push up the dome insert until both tabs click into place. Be sure that
you hear two clicks.
Tab
Figure 3-5. Installing Dome Drive
6). Take out the lower housing from the dome package. Line up the screw holes of the lower housing with
corresponding holes on the housing, and then secure the cover with supplied pan head screws.
Figure 3-6. Installing Dome Bubble
8/4/2019 9840 IP Dome Mount Installation Manual
12/26
DVTel IP Dome Mounting Instructions
- 12 -
7). Turn on the power. The dome will pan, tilt, and zoom to initiate system parameters as well as to verify the
normal operation of the dome drive.
After the initiation sequence, the dome will stop and be ready for programming and operation.
8/4/2019 9840 IP Dome Mount Installation Manual
13/26
DVTel IP Dome Mounting Instructions
- 13 -
4 Corner Mounting [For both indoor and outdoor mounting]
4.1 Corner Mounting Specifications [For indoor mounting]Below figures demonstrate the corner mounting specifications:
310
280
130
80
100
60
120
A
225
140
70
R76
A VIEW
154
218
O
O
8- 7O
4.2 Corner Mounting Specifications [For outdoor mounting]Below figures demonstrate the corner mounting specifications:
8/4/2019 9840 IP Dome Mount Installation Manual
14/26
DVTel IP Dome Mounting Instructions
- 14 -
280
310
265
162
150
245
70
R76
240O
218O
O8- 7
130
80
100
60
120
A
A VIEW
4.3 Installation Procedures For Corner Mounting
Easily install your DVTel IP Dome in below 8 steps:
1). Place the bracket base at a suitable position against the corner, and secure it with eight expansion bolts. Pull
the wiring through the bracket hole. For dimensional diagram of the bracket base, please refer to the following
figure.
A derection
seen from Aderection
Figure 4-1. Installing Bracket Base
2). Use the four screws supplied with the mount bracket to secure the bracket onto the base. Pull the power and
Cat-5 cables through the mount bracket.
Deleted:
8/4/2019 9840 IP Dome Mount Installation Manual
15/26
DVTel IP Dome Mounting Instructions
- 15 -
Figure 4-2. Installing Mount Bracket
3). Take out the upper housing from the dome package. Loosen the bolt that holds the connection circuit board,
and lift the board to make an opening for wiring.
Figure 4-3. Lifting Connection Board
4). Pull the cables through the opening, and then screw the upper housing onto the mount bracket. For outdoor
housing, it is recommended to apply thread compound to the threads on the housing. Secure the connection
with a holding screw.
8/4/2019 9840 IP Dome Mount Installation Manual
16/26
DVTel IP Dome Mounting Instructions
- 16 -
Holding Screw
Figure 4-4. Installing Housing
5). Take out the dome drive from the dome package. If necessary, set the camera ID by configuring the DIP
switch S1 (see Figure 4-5). For details on how to configure the DIP switch, please refer toAppendix I. Most
installation will use the default settings.
S1
Figure 4-5. DIP Switch S1
6). Line up the two taps located on the upper side of the dome drive with the corresponding grooves in the
housing. Insert both tabs into the grooves. Push up the dome insert until both tabs click into place. Be sure that
you hear two clicks.
Tab
Figure 4-6. Installing Dome Drive
7. Take out the lower housing from the dome package. Line up the screw holes of the lower housing with
Deleted:
Page Break
8/4/2019 9840 IP Dome Mount Installation Manual
17/26
DVTel IP Dome Mounting Instructions
- 17 -
corresponding holes on the housing, and then secure the cover with supplied pan head screws.
Figure 4-7. Installing Dome Bubble
8). Turn on the power. The dome will pan, tilt, and zoom to initiate system parameters as well as to verify the
normal operation of the dome drive.
After the initiation sequence, the dome will stop and be ready for programming and operation.
8/4/2019 9840 IP Dome Mount Installation Manual
18/26
DVTel IP Dome Mounting Instructions
- 18 -
5 Pole Mounting [For both indoor and outdoor mounting]5.1 Pole Mounting Specifications [For indoor mounting]Below figures demonstrate the Pole mounting specifications:
40
4 5
128
R5
310
280
225
140
70
R76
DO
154O
218O
5.2 Pole Mounting Specifications [For outdoor mounting]Below figures demonstrate the Pole mounting specifications:
280
310
R5
45
40
R7670
245
150
162
265
DO
240O
218O
8/4/2019 9840 IP Dome Mount Installation Manual
19/26
DVTel IP Dome Mounting Instructions
- 19 -
5.3 Installation Procedures For Pole Mounting
Easily install your DVTel IP Dome in below 9 steps:
1). Place the bracket base at a suitable position against the pole, and secure it to the pole with two clamps. Pull
the wiring through the bracket hole.
BracketBase
Clamps
Figure 5-1. Installing Bracket Base
2). Use the four screws supplied with the mount bracket to secure the bracket onto the base. Pull the power and
Cat-5 cables through the mount bracket.
Mounting Bracket
Figure 5-2. Installing Mount Bracket
3). Take out the upper housing from the dome package. Loosen the bolt that holds the connection circuit board,
and lift the board to make an opening for wiring.
Figure 5-3. Lifting Connection Board
8/4/2019 9840 IP Dome Mount Installation Manual
20/26
DVTel IP Dome Mounting Instructions
- 20 -
4). Pull the cables through the opening, and then screw the upper housing onto the mount bracket. For outdoor
housing, it is recommended to apply thread compound to the threads on the housing.Secure the connection with
a holding screw.
Holding Screw
Figure 5-4. Installing Housing
6. 5). Take out the dome drive from the dome package. If necessary, set the camera ID by configuring the
DIP switch S1 (see Figure 5-5). For details on how to configure the DIP switch, please refer to Appendix I.
Most installation will use the default settings.
S1
Figure 5-5. DIP Switch S1
6). Line up the two taps located on the upper side of the dome drive with the corresponding grooves in the
housing. Insert both tabs into the grooves. Push up the dome insert until both tabs click into place. Be sure that
you hear two clicks.
Tab
Figure 5-6. Installing Dome Drive
8/4/2019 9840 IP Dome Mount Installation Manual
21/26
DVTel IP Dome Mounting Instructions
- 21 -
7). Take out the lower housing from the dome package. Line up the screw holes of the lower housing with
corresponding holes on the housing, and then secure the cover with supplied pan head screws.
Figure 5-7. Installing Dome Bubble
8). Turn on the power. The dome will pan, tilt, and zoom to initiate system parameters as well as to verify the
normal operation of the dome drive.
After the initiation sequence, the dome will stop and be ready for programming and operation.
8/4/2019 9840 IP Dome Mount Installation Manual
22/26
DVTel IP Dome Mounting Instructions
- 22 -
6 Pendant Mounting [For indoor mounting only]6.1 Pendant Mounting Specifications
Below figures demonstrate the Pendant mounting specifications:
R7670
140
225
50
40
15
A ViewA
O218
154O
57O
60O
4- 6.5Through
Evenly Distributing
265
O
85O100
O
6.2 Installation Procedures For Pendant Mounting
Easily install your DVTel IP Dome in below 9 steps:
1). Place the pendant mount base at a suitable position against firm ceiling, and secure it with three expansion
bolts. Pull the wiring through the base hole.
For dimensional diagram of the pendant mount base, please refer to the following figure.
Through
Average
Bottom
Figure 6-1. Installing Mount Base
8/4/2019 9840 IP Dome Mount Installation Manual
23/26
DVTel IP Dome Mounting Instructions
- 23 -
2). Screw the suspender into the pendant mount base, and then the housing holder into the suspender. Secure
the connections with holding screws. Pull the power and Cat-5 cables through the three connected accessories.
Figure 6-2. Installing Suspender and Housing Holder
3). Take out the upper housing from the dome package. Loosen the bolt that holds the connection circuit board,
and lift the board to make an opening for wiring.
Figure 6-3. Lifting Connection Board
4). Pull the cables through the opening, and then screw the upper housing onto the housing holder. Secure the
connection with two holding screws.
Figure 6-4. Installing Housing
8/4/2019 9840 IP Dome Mount Installation Manual
24/26
DVTel IP Dome Mounting Instructions
- 24 -
7. 5). Take out the dome drive from the dome package. If necessary, set the camera ID by configuring the
DIP switch S1 (see Figure 6-5). For details on how to configure the DIP switch, please refer to Appendix I.
Most installation will use the default settings.
S1
Figure 6-5. DIP Switch S1
6). Line up the two taps located on the upper side of the dome drive with the corresponding grooves in the
housing. Insert both tabs into the grooves. Push up the dome insert until both tabs click into place. Be sure thatyou hear two clicks.
Tab
Figure 6-6. Installing Dome Drive
8/4/2019 9840 IP Dome Mount Installation Manual
25/26
DVTel IP Dome Mounting Instructions
- 25 -
7). Take out the lower housing from the dome package. Line up the screw holes of the lower housing with
corresponding holes on the housing, and then secure the cover with supplied pan head screws.
Figure 6-7. Installing Dome Bubble
8). Turn on the power. The dome will pan, tilt, and zoom to initiate system parameters as well as to verify the
normal operation of the dome drive.
After the initiation sequence, the dome will stop and be ready for programming and operation.
8/4/2019 9840 IP Dome Mount Installation Manual
26/26
DVTel IP Dome Mounting Instructions
- 26 -
Assembly and Disassembly Procedures
Assembly Procedures
Line up the two taps located on the upper side of the dome drive with the corresponding grooves in the housing.
Insert both tabs into the grooves. Push up the dome insert until both tabs click into place. Be sure that you hear
two clicks.
Tab
Disassembly Procedures
Disassembly is the inverse procedure of installation. Ensure that the disassembly must be carried out after the
dome power has been turned off.
Note: The following instructs how to disassemble the dome drive:
Hold the dome drive at the bottom of the two taps located on the upper side of the dome drive. Then use your
fingers to press inward until they are divorced from the grooves in the housing. Keeping the taps and the grooves
at this status, pull the dome drive down slowly.
Press Inward