Date post: | 13-Apr-2015 |
Category: |
Documents |
Upload: | hugo-luis-escalante |
View: | 237 times |
Download: | 5 times |
bizhub PRO950
KONICA MINOLTA BUSINESS TECHNOLOGIES, INC.
SYSTEM SETTING
biz
hu
b P
RO
95
0
9. SERField Service Ver.2.0 Sep. 2009
9.9 System setting
9.9.1 Software DIPSW Setting
Configure settings for the software DIPSW.
Note
• DIPSW bits data are written into the NVRAM board (NRB) every time a change is made. Do not
change data hastily, for they cannot be automatically restored. Do not change any switch not
described in the service manual.
A. Procedure
B. Software DIPSW setting screen
1. "Service mode menu screen"Press [07 System Setting].
2. "System Setting menu screen"Press [01 Software DIPSW Setting].
3. "Software DIPSW Setting screen"Press the [↑], [↓] or the numeric keys to select DIPSW bit number.
4. Press [On (1)] or [Off (0)] to set the selected bit number ON/OFF.
5. Press [Return] to return to the "Service mode menu screen" on which the sub menu was displayed.
[1] DIPSW number [3] Bit number (0 to 7)
[2] DIPSW date (The bit data (8 bits) of the DIPSW number selected is displayed in hexadecimals from 00 to FF)
[4] Bit data
[5] Numeric keys
[1] [2] [3] [4] [5]
VICE MODE
229
MODE
2
Field Service Ver.2.0 Sep. 2009b
izh
ub
PR
O 9
50
1
C. List of software DIPSW
Note
• Be sure not to change bits with no particular reference made of the function.
DIPSW No Bit Function 0 1 Default setting
Japan Inch Metric
DIPSW1 0 Print stop condition after toner supply display
*1 *1 1 1 1
1 *1 *1 0 0 0
2 Print stop method after toner supply display
*2 *2 1 1 1
3 *2 *2 0 0 0
4 Prohibition of printing when the PM count is reached
Disabled Enabled 0 0 0
5 Print number setting until print-ing is prohibited after PM is displayed
*3 *3 0 0 0
6 *3 *3 0 0 0
7 *3 *3 0 0 0
DIPSW2 0 — — — 0 0 0
1 All charger cleaning cycle (fus-ing temperature 50°C or less when turning ON)
*4 *4 0 0 0
2 *4 *4 0 0 0
3 *4 *4 0 0 0
4 All charger cleaning cycle (after print out)
*5 *5 0 0 0
5 *5 *5 0 0 0
6 Blade auto switch timing *6 *6 1 1 1
7 *6 *6 0 0 0
DIPSW3 0 Regular toner supply amount *7 Equivalent to 2% of coverage
*7 Equivalent to 0.4% of coverage
0 0 0
1 Error code latch (C-35**, C-38**, C-39**)
Unlatched Latched 0 0 0
2 Transfer assist timing adjustment Enabled Disabled 1 1 1
3 Charger cleaning function Enabled Disabled 0 0 0
4 Transfer/separation charger cleaning function
Enabled Disabled 0 0 0
5 — — — 0 0 0
6 I/O check mode output 15 memory clear
Disabled Enabled 0 0 0
7 — — —
DIPSW4 0 DF auto skew adjustment Enabled Disabled 0 0 0
1 — — — 0 0 0
2 — — — 0 1 1
3 — — — 0 0 0
4 Key counter removal recovery Disabled Enabled 0 0 0
5 APS when change magnification Enabled Disabled 0 0 1
6 DF mode is kept active even if opened and closed DF.
Not to keep the DF mode
To keep the DF mode
0 0 0
7 Large-size paper count method (other than maintenance counter)
1 count 2 counts 0 0 0
9. SERVICE
30
biz
hu
b P
RO
95
0
9. SERField Service Ver.2.0 Sep. 2009
DIPSW5 0 Waste toner box full message display timing when RC is con-nected
65 to 80% :Near full display80% or more :
Full display
45 to 60% :Near full display60% or more :
Full display
0 0 0
1 Print operation when waste toner box is full
Prohibited (C-2250)
Allowed (Switch to recycle toner control)
0 0 0
2 Image density selection (laser PWM) for copier
*8 *8 0 0 0
3 *8 *8 0 0 0
4 — — — 0 0 0
5 — — — 0 0 0
6 — — — 0 0 0
7 — — — 0 0 0
DIPSW6 0 Background density adjust-ment (photo mode)
*9 *9 0 0 0
1 *9 *9 1 1 1
2 Transfer assist control Enabled Disabled 0 0 0
3 Min. black band width in black band creation control
*10 *10 0 0 0
4 *10 *10 0 0 0
5 Image stabilization control cycle
*11 *11 1 1 1
6 *11 *11 0 0 0
7 Drum potential auto adjustment Enabled Disabled 0 0 0
DIPSW7 0 Fusing cleaning web feed con-trol
*12 *12 0 0 0
1 *12 *12 0 0 0
2 Background density adjustment *13 *13 0 0 0
3 *13 *13 0 0 0
4 Drum claw contacted/released control
*14 *14 0 0 0
5 *14 *14 0 0 0
6 — — — 0 0 0
7 Drum claw control *15 Normal *15 Side2 only 0 0 0
DIPSW8 0 Image density selection (laser PWM) for printer
*16 *16 0 0 0
1 *16 *16 0 0 0
2 Fusing initial rotation condition *17 *17 0 0 0
3 *17 *17 1 1 1
4 Fusing roller initial rotation time *18 *18 0 0 0
5 *18 *18 0 0 0
6 Large-size paper count method (maintenance counter)
1 count 2 counts 0 0 0
7 Fusing preparative rotation control after printing of small-size paper
*19 Disabled *19 Enabled 0 0 0
DIPSW9 0 Operation at key counter removal (copier)
Same as the stop key
Immediate stop (jam)
0 1 1
1 Operation at key counter removal (printer)
Ignored Same as DIPSW9-0
0 0 0
DIPSW No Bit Function 0 1 Default setting
Japan Inch Metric
VICE MODE
231
MODE
2
Field Service Ver.2.0 Sep. 2009b
izh
ub
PR
O 9
50
DIPSW9 2 Message switchover *20 *20 0 0 0
3 *20 *20 0 0 0
4 Copy quantity limit *21 *21 0 0 0
5 *21 *21 0 0 0
6 *21 *21 0 0 0
7 *21 *21 0 0 0
DIPSW10 0 Image memory usable area *22 *22 0 0 0
1 *22 *22 0 0 0
2 — — — 0 0 0
3 Definition change of the large size paper in counter control
*23 *23 0 0 0
4 *23 *23 0 0 0
5 — — — 0 0 0
6 — — — 0 0 0
7 — — — 0 0 0
DIPSW11 0 — — — 0 0 0
1 — — — 0 0 0
2 Erasure amount of trailing edge of tab paper
3mm 1mm 0 0 0
3 Error code screen switchover F/E code screen switch
F code screen only
0 0 0
4 Filter for jagged edges on slanting lines
Disabled Enabled 0 0 0
5 Gradation switchover in the photo mode
2bitED 1bitED 0 0 0
6 Paper feed automatic start Disabled Enabled 0 0 0
7 Jam code display Disabled Enabled 0 0 0
DIPSW12 0 Switching of default Job List screen when using RC
Enabled Disabled 1 1 1
1 IC scanner key counter check Disabled Enabled only when no JOB
0 0 0
2 — — — 0 0 0
3 Printer auto centering correction Enabled Disabled 0 0 0
4 — — — 0 0 0
5 RC recognition Disabled Enabled 0 0 0
6 Konica Minolta logo when power switch is turned ON
Enabled Disabled 0 0 0
7 — — — 0 0 0
DIPSW13 0 Original size detection switchover 1 A5 51/2 x 81/2 0 1 0
1 Original size detection switchover 2 A4S 81/2 x 11S 0 1 0
2 — — — 0 0 0
3 Original size detection switchover 3 *24 *24 0 0 0
4 *24 *24 0 0 0
DIPSW No Bit Function 0 1 Default setting
Japan Inch Metric
9. SERVICE
32
biz
hu
b P
RO
95
0
9. SERField Service Ver.2.0 Sep. 2009
DIPSW13 5 Original size detection switchover 4 *25 *25 0 0 0
6 *25 *25 0 0 0
7 *25 *25 1 1 0
DIPSW14 0 Original size detection switchover 5 B4, 11 x 17/B5, 81/2 x 11
8K/16K 0 0 0
1 — — — 0 0 0
2 — — — 0 0 0
3 — — — 0 0 0
4 Custom size paper feeding direction switchover
LEF SEF 0 0 0
5 Size standard switchover of B series paper
JIS ISO 0 0 1
6 CRC (Cyclic Redundancy Check) in ISW implementation
Checked Not checked 0 0 0
7 — — — 0 0 0
DIPSW15 0 Transfer assist sheet press control on side1
*26 No press *26 With press 0 0 0
1 Number of paper that can be stapled
*27 *27 0 0 0
2 *27 *27 0 0 0
3 Finishing option alarm stop *28 *28 0 0 0
4 *28 *28 0 0 0
5 CS Remote Care recognition Disabled Enabled 0 0 0
6 Maximum density in printer mode Darker (1.43) Lighter (1.35) 0 0 0
7 Trigger the display of devel-oper/drum replacement icon
Number of prints Running time 0 0 0
DIPSW16 0 Developer/drum running time display
Displayed Not displayed 0 0 0
1 Copy reservation function Enabled Disabled 0 0 0
2 Tab original duplex (DF) Prohibited Allowed 0 0 0
3 Count of the key counter in printer mode
Disabled Enabled 0 0 0
4 Utility mode installation date display
Enabled Disabled 0 0 0
5 Non-image area erase mode judge level
*29 *29 0 0 0
6 *29 *29 0 0 0
7 NIC selection for E-mail CS Remote Care
Controller NIC Machine NIC 0 0 0
DIPSW17 0 Summer time setting *30 *30 0 0 0
1 *30 *30 1 1 1
2 *30 *30 1 1 1
3 *30 *30 0 0 0
4 Density selection at scanning tab paper
*31 *31 0 0 0
5 *31 *31 0 0 0
DIPSW No Bit Function 0 1 Default setting
Japan Inch Metric
VICE MODE
233
MODE
2
Field Service Ver.2.0 Sep. 2009b
izh
ub
PR
O 9
50
1
DIPSW17 6 Density selection at scanning tab paper
*31 *31 0 0 0
7 Custom size paper image rota-tion on printer output
Disabled Enabled 1 1 1
DIPSW18 0 Faulty part isolation: Tray 1 Normal Unavailable 0 0 0
1 Faulty part isolation: Tray 2 Normal Unavailable 0 0 0
2 Faulty part isolation: Tray 3 Normal Unavailable 0 0 0
3 Faulty part isolation: Tray 4 Normal Unavailable 0 0 0
4 Faulty part isolation: DF Normal Unavailable 0 0 0
5 Faulty part isolation: Folding/saddle stitching/TU
Normal Unavailable 0 0 0
6 Faulty part isolation: PI Normal Unavailable 0 0 0
7 Faulty part isolation: HDD1 Normal Unavailable 0 0 0
DIPSW19 0 Fusing temperature setting *32 *32 1 0 0
1 *32 *32 0 0 0
2 *32 *32 1 0 0
3 *32 *32 0 0 0
4 Faulty part isolation: ZU Normal Unavailable 0 0 0
5 Faulty part isolation: Punch (PK, ZU) Normal Unavailable 0 0 0
6 Max. black band width for black band creation control (when RC is connected)
*33 *33 0 0 0
7 *33 *33 0 0 0
DIPSW20 0 — — — 0 0 0
1 Image scanning area with "Page Margin" function
*34 Normal *34 Original priority 0 0 0
2 Total page number standard in stamp mode
Based on original Based on transfer paper
0 0 0
3 — — — 0 0 0
4 — — — 0 0 0
5 — — — 0 0 0
6 — — — 0 0 0
7 Tandem connection recognition Disabled Enabled 0 0 0
DIPSW21 0 Mixed size paper staple and punch for printer
Allowed (real-time output)
Prohibited (batch output)
0 0 0
1 Double side print size specification of printer job (This setting prints on the singular paper when the speci-fied size is different from the front to back side.)
Disabled Enabled 0 0 0
2 Fusing heat roller temperature control
*35 *35 0 0 0
3 Removal of paper weight limi-tation with the duplex print.
Disabled Enabled 0 0 0
DIPSW No Bit Function 0 1 Default setting
Japan Inch Metric
9. SERVICE
34
biz
hu
b P
RO
95
0
9. SERField Service Ver.2.0 Sep. 2009
DIPSW21 4 — — — 0 0 0
5 Touch panel adjustment method switchover
Setting menu + hard key
Hard key only 0 0 0
6 — — — 0 0 0
7 Scanner screen reset button Mode Reset Mode reset + move to the
sending direction select screen
0 0 0
DIPSW22 0 Machine NIC setting Disabled Enabled 1 1 1
1 Number of punch holes *36 *36 0 1 0
2 *36 *36 0 0 1
3 Image position for the custom size original (at DF)
Based on user selection
Based on APS at DF
0 0 0
4 Function of power save button Enabled Disabled 0 0 0
5 Punch auto switching (PK and ZU) Disabled Enabled 0 0 0
6 Operation when staple empty of FS
Request staple supply
Selectable staple supply or staple
release
0 0 0
7 Jam screen selection Jam position display
Described by illustration
0 0 0
DIPSW23 0 Change of staple limit control method of FS-528. (1-staple/2-staple)
different control common control 0 0 0
1 Removal of limitation in the combination of “half fold and trimming”.*Output with "Enabled" is out of specification.
Disabled Enabled 0 0 0
2 Toner concentration of devel-oper selection
*37 *37 0 0 0
3 *37 *37 0 0 0
4 *37 *37 0 0 0
5 — — — 0 0 0
6 — — — 0 0 0
7 Custom size image rotation switchover (LEF original → SEF paper)
Rotates Not rotate 0 0 0
DIPSW24 0 New developing unit support. Old style developing unit
New style developing unit
1 1 1
1 — — — 0 0 0
2 — — — 0 0 0
3 Finisher rear side staple angle 45° diagonally Parallel 0 0 0
4 Z-fold output number limit *38 *38 0 0 0
5 *38 *38 0 0 0
DIPSW No Bit Function 0 1 Default setting
Japan Inch Metric
VICE MODE
235 1
MODE
2
Field Service Ver.2.0 Sep. 2009b
izh
ub
PR
O 9
50
1
DIPSW24 6 Z-fold + Staple output number limit
*39 *39 0 0 0
7 *39 *39 0 0 0
DIPSW25 0 Addition of the stop control selection on no feed jam at the PI.
At JAM paper stay
At JAM no paper stay
0 0 0
1 — — — 0 0 0
2 — — — 0 0 0
3 — — — 0 0 0
4 — — — 0 0 0
5 — — — 0 0 0
6 — — — 0 0 0
7 TU trimming permitted number switchover
20 sheets 16 sheets 0 0 0
DIPSW26 0 Transfer assist control size switchover
*40 *40 0 1 0
1 *40 *40 0 0 0
2 — — — 0 0 0
3 — — — 0 0 0
4 — — — 0 0 0
5 — — — 0 0 0
6 — — — 0 0 0
7 — — — 0 0 0
DIPSW27 0 Paper weight, process speed switch table
*41 *41 0 1 1
1 Fusing roller switchover Soft roller Hard roller 1 1 1
2 Image density selection (toner control patch density)
*42 *42 0 0 0
3 *42 *42 0 0 0
4 — — — 0 0 0
5 Thin characters reproduction improvement (usage of smaller laser dot)
Standard Thin-character correspondent
0 0 0
6 Transfer assist control when the paper weight is more than 92g/m2
Pressed Not pressed 0 0 0
7 — — — 0 0 0
DIPSW28 0 Selection of page margin method set on main body for printer job
Side1 and side2 collectively
Side1 and side2 separately
0 0 0
1 — — — 0 0 0
2 Changing direction of adjusting print start position at back side in fine increments (other than book)
Shift to the oppo-site direction to the front side
Shift to the same direction as the
front side
0 0 0
3 Changing direction of adjusting print start position at back side in fine increments (book)
Shift to the same direction as the
front side
Shift to the oppo-site direction to the front side
0 0 0
DIPSW No Bit Function 0 1 Default setting
Japan Inch Metric
9. SERVICE
36
biz
hu
b P
RO
95
0
9. SERField Service Ver.2.0 Sep. 2009
DIPSW28 4 Image shift when outputting the custom size print job
*43 Paper stan-dard
*43 Image stan-dard
0 0 0
5 — — — 0 0 0
6 Standard of shifting with the shifting direction specified 2 repeats.
Image standard Paper standard 0 0 0
7 — — — 0 0 0
DIPSW29 0 — — — 0 0 0
1 — — — 0 0 0
2 — — — 0 0 0
DIPSW29 3 Include of proof copy to the set copy quantity
Not included Included 0 0 0
4 Transfer exposure lamp (EL2) light volume switchover at the trailing edge of paper
*44 *44 1 1 1
5 *44 *44 0 0 0
6 *44 *44 0 0 0
7 — — — 0 0 0
DIPSW30 0 — — — 0 0 0
1 Service mode, restriction of data collection display
Restricted Not restricted 0 0 0
2 — — — 0 0 0
3 — — — 0 0 0
4 — — — 0 0 0
5 — — — 0 0 0
6 — — — 0 0 0
7 Test pattern No. 16 paper size switchover
A3 (Test pattern No. 16)
11 x 17 (Test pat-tern No. 33)
0 1 0
DIPSW31 0 — — — 1 1 1
1 — — — 0 0 0
2 Printer input delay control *45 *45 0 0 0
3 *45 *45 0 0 0
4 — — — 0 0 0
5 — — — 0 0 0
6 — — — 0 0 0
7 — — — 0 0 0
DIPSW32 0 — — — 0 0 0
1 — — — 0 0 0
2 — — — 0 0 0
3 — — — 0 0 0
4 — — — 1 1 1
5 While in the platen mode, 180 degrees rotated
Enabled Disabled 0 0 0
6 — — — 1 1 1
DIPSW No Bit Function 0 1 Default setting
Japan Inch Metric
VICE MODE
237 1
MODE
2
Field Service Ver.2.0 Sep. 2009b
izh
ub
PR
O 9
50
1
DIPSW32 7 — — — 0 0 0
DIPSW33 0 — — — 0 0 0
1 — — — 0 0 0
2 — — — 0 0 0
3 — — — 0 0 0
4 — — — 0 0 0
5 — — — 0 0 0
6 — — — 0 0 0
7 — — — 0 0 0
DIPSW34 0 — — — 0 0 0
1 — — — 0 0 0
2 — — — 0 0 0
3 — — — 0 0 0
4 — — — 0 0 0
5 — — — 0 0 0
6 — — — 0 0 0
7 — — — 0 0 0
DIPSW35 0 — — — 0 0 0
1 — — — 0 0 0
2 — — — 0 0 0
3 — — — 0 0 0
4 — — — 0 0 0
5 — — — 0 0 0
6 Faulty part isolation: Multi punch Normal Unavailable 0 0 0
7 — — — 0 0 0
DIPSW36 0 — — — 0 0 0
1 — — — 0 0 0
2 — — — 0 0 0
3 — — — 0 0 0
4 — — — 0 0 0
5 — — — 0 0 0
6 — — — 0 0 0
7 — — — 1 1 1
DIPSW37 0 — — — 0 0 0
1 — — — 0 0 0
2 FS bypass control Enabled Disabled 0 0 0
3 Tab paper + punch Disabled Enabled 0 0 0
4 — — — 0 0 0
5 — — — 0 0 0
6 — — — 0 0 0
7 — — — 0 0 0
DIPSW No Bit Function 0 1 Default setting
Japan Inch Metric
9. SERVICE
38
biz
hu
b P
RO
95
0
9. SERField Service Ver.2.0 Sep. 2009
DIPSW38 0 Default folder when selecting box function Personal Folder Public Folder 0 0 0
1 File name over writting with box function Disabled Enabled 0 0 0
2 Print quantity and output page selection for Wait or Proof output for box function
Enabled Disabled 0 0 0
3 Center folding + Inside printing Disabled Enabled (Copier, printer, sin-
gle side printing)
0 0 0
4 Automatic change of tray set-ting names
*46 *46 0 0 0
5 — — — 0 0 0
DIPSW38 6 — — — 0 0 0
7 — — — 0 0 0
DIPSW39 0 — — — 0 0 0
1 — — — 0 0 0
2 Half folding permitted number limit
3 sheets 5 sheets 0 0 0
3 — — — 0 0 0
4 — — — 0 0 0
5 — — — 0 0 0
6 — — — 0 0 0
7 — — — 0 0 0
DIPSW40 0 — — — 0 0 0
1 Overwrite all HDD data *47 *47 0 0 0
2 — — — 0 0 0
3 — — — 0 0 0
4 Insert sheet SEF/LEF mixed output setting
Restrict the mixed output
Permit the mixed output
0 0 0
5 — — — 0 0 0
6 — — — 0 0 0
7 Image rotation on IC scanner mixed original
Restrict the rota-tion
Permit the rota-tion
0 0 0
DIPSW41 0 — — — 0 0 0
1 — — — 0 0 0
2 — — — 0 0 0
3 — — — 0 0 0
4 — — — 0 0 0
5 — — — 0 0 0
6 — — — 0 0 0
7 — — — 0 0 0
DIPSW42 0 — — — 0 0 0
1 TIFF direct printPaper size for APS (F4)
*48 *48 0 0 0
2 *48 *48 0 0 0
DIPSW No Bit Function 0 1 Default setting
Japan Inch Metric
VICE MODE
239
MODE
2
Field Service Ver.2.0 Sep. 2009b
izh
ub
PR
O 9
50
DIPSW42 3 — — — 0 0 0
4 — — — 0 0 0
5 TIFF direct print resolution change
*49 *49 0 0 0
6 — — — 0 0 0
7 — — — 0 0 0
DIPSW43 0 Scanner compression method change
MMR MH 0 0 0
1 — — — 0 0 0
2 — — — 0 0 0
DIPSW43 3 — — — 0 0 0
4 — — — 0 0 0
5 — — — 0 0 0
6 — — — 0 0 0
7 — — — 0 0 0
DIPSW44 0 — — — 0 0 0
1 — — — 0 0 0
2 — — — 0 0 0
3 — — — 0 0 0
4 — — — 0 0 0
5 — — — 0 0 0
6 — — — 0 0 0
7 — — — 0 0 0
DIPSW45 0 — — — 0 0 0
1 — — — 0 0 0
2 — — — 0 0 0
3 — — — 0 0 0
4 — — — 0 0 0
5 — — — 0 0 0
6 — — — 0 0 0
7 — — — 0 0 0
DIPSW46 0 Visual Count Master counter value acquisition intervals
*50 *50 0 0 0
1 *50 *50 0 0 0
2 — — — 0 0 0
3 Font backup data creation but-ton display
Disabled Enabled 0 0 0
4 — — — 0 0 0
5 — — — 0 0 0
6 — — — 0 0 0
7 — — — 0 0 0
DIPSW No Bit Function 0 1 Default setting
Japan Inch Metric
9. SERVICE
40
biz
hu
b P
RO
95
0
9. SERField Service Ver.2.0 Sep. 2009
Note
• Bold boxes show default settings.
*1 Print stop condition after toner supply displaySelect the number of prints that stops printing after atoner near empty displays.
*2 Print stop method after toner supply displaySelect the method to stop printing when the numberspecified with DIPSW1-0/1 is reached.
*3 Print number setting until printing is prohibitedafter PM is displayed
Select the number of prints that stops printing afterthe value specified with the maintenance counter isreached.
*4 All charge cleaning cycle (fusing temperature50°C or less when turning ON
Set the timing for the electrode cleaning, which isperformed on the condition that the fusing tempera-ture is below 50°C when the power is turned on.
*5 Cycle number setting of the electrode cleaning(after print out)
Set the intervals of the electrode cleaning that is con-ducted after turning on the power.
Mode 1-1 1-0
Stops after 1,500 prints 0 0
Stops after 3,000 prints 0 1
Stops after 4,000 prints 1 0
Stops after 5,000 prints 1 1
Mode 1-3 1-2
Stops after exit paper in the machine
0 0
Stops at a break between print set
0 1
Stops at the end of the current job
1 0
Does not stop 1 1
Mode 1-7 1-6 1-5
1,000 prints 0 0 0
2,000 prints 0 0 1
3,000 prints 0 1 0
4,000 prints 0 1 1
5,000 prints 1 0 0
1,000 prints 1 0 1
1,000 prints 1 1 0
1,000 prints 1 1 1
Mode 2-3 2-2 2-1
Cleaning every time 0 0 0
At 5,000 prints 0 0 1
At 10,000 prints 0 1 0
At 15,000 prints 0 1 1
At 20,000 prints 1 0 0
At 25,000 prints 1 0 1
At 30,000 prints 1 1 0
No cleaning 1 1 1
Mode 2-5 2-4
Every 10,000 prints 0 0
Every 20,000 prints 0 1
Every 30,000 prints 1 0
Every 5,000 prints 1 1
VICE MODE
241
MODE
2
Field Service Ver.2.0 Sep. 2009b
izh
ub
PR
O 9
50
*6 Blade auto switching timingSet the auto switch timing of the cleaning blade.
*7 Regular toner supply amountWhen the original with less coverage (1% or less) isprinted for a long period of time, the toner density ofdeveloper gets increased, causing the image background to occur. Changing this switch to "1" reducesthe toner amount periodically supplied to prevent theimage back ground.
Note
• Changing this switch to 1 in the original hav-
ing a typical blacking ratio results in the
image getting light colored.
*8 Image density selection (laser PWM) for copierChange the image writing laser PWM to make imagelighter.
Note
• There are two kinds of DIPSWs to lighten
image density: laser PWM (5-2/3) and toner
control patch density (27-2/3). As a priority of
adjustment, adjust in the following order.
1) Laser PWM
2) Toner control patch density: approx. 0.5%
down
Using this setting alone may cause white
spot on the solid section. Be sure to use
together with DIPSW23-2/3/4 (toner den-
sity of developer) approx. 0.25% up or
0.5% up.
*9 Background density adjustment (photo mode)Change the laser PWM and set the image density forthe highlight section while in the photo mode.The numerical values given in the table represent thedensity in the image density range of 0 (white) to 255(black).
Mode 2-7 2-6
At 150,000 prints 0 0
At 250,000 prints 0 1
At 300,000 prints 1 0
At 400,000 prints 1 1
Mode 3-0
Equivalent to 2% of coverage 0
Equivalent to 0.4% of coverage 1
Mode 5-3 5-2
Standard (*190/170) 0 0
Lighter (*1167/137) 0 1
Lightest (*142/112) 1 0
Standard (*190/170) 1 1
* 0 (white) to 255 (black) represent density withinthe image density range. Numbers representeach image density at the line speed 460mm/s,290mm/s from left.
Mode 6-1 6-0
PWM 16 0 0
PWM 0 0 1
PWM 8 1 0
PWM 24 1 1
9. SERVICE
42
biz
hu
b P
RO
95
0
9. SERField Service Ver.2.0 Sep. 2009
*10 Min. black band width in black band creationcontrol
Set the black band width in the black band creation
control.
*11 Image stabilization control cycleChanges cycle of the image stabilization control(drum potential, maximum density, gamma autoadjustment).
*12 Fusing cleaning web feed control Under the automatic control, the feeding amountcontrol of the fusing cleaning web is twice as muchas the usual in high coverage mode. Therefore, the feeding amount of the fusing cleaningweb can be fixed with this setting if the high coverageoriginals are printed frequently.
Note
• If the fusing cleaning web feeding amount
is fixed, it has a possibility of the soiled
image or the fusing cleaning web getting to
its life before PM.
*13 Background density adjustmentChange the charging potential and set the imagedensity of the highlight section.
*14 Drum contacted/released control If the drum claw is judged as needless for the paperthat is easy to separate, setting to "Not contact"reduces the damage by the claw. Setting to "Alwayscontact during JOB" also reduces the damage forsome kinds of paper.
Mode 6-4 6-3
0.25mm 0 0
0.5mm 0 1
0.75mm 1 0
No band 1 1
Mode 6-6 6-5
Every 10,000 prints 0 0
Every 20,000 prints 0 1
Every 30,000 prints 1 0
Every 50,000 prints 1 1
Mode 7-1 7-0
Automatic control 0 0
Fixed to 1/2 feeding amount (low coverage control)
0 1
Fixed to the normal con-trol
1 0
Fixed to twice feeding amount (high coverage control)
1 1
Mode 7-3 7-2
Standard 0 0
Dark (25 V down) 0 1
Lighter (25 V up) 1 0
Lightest (50 V up) 1 1
Mode 7-5 7-4
Contact/release for every 1 print
0 0
Always contact during JOB (Release after JOB)
0 1
Not contact 1 0
Contact/release for every 1 print
1 1
VICE MODE
243
MODE
2
Field Service Ver.2.0 Sep. 2009b
izh
ub
PR
O 9
50
*15 Drum claw controlFor the operation of the drum claw, switching is madebetween the normal operation (operated on both the
front and the rear) and the operation only on the rear.When paper with much paper dust is used and thedrum is damaged by paper dust adhering to thedrum claw, select the operation only on the rear.
*16 Image density selection (laser PWM) for printerChange the image writing laser PWM to make imagelighter.
*17 Fusing initial rotation conditionIn the low temperature environment, fusibility may beinsufficient immediately after the power is turned ON.So, rotate the fusing roller while in the warm-up toobtain an even heat distribution of the fusing roller toavoid the insufficient fusing. • Low temperature: perform the fusing initial rotation
in the low temperature environment only.• Low/normal temperature: perform the fusing initial
rotation in the low and normal temperature envi-ronment
• Low/normal/high temperature: perform the fusinginitial rotation in all environments.
*18 Fusing roller initial rotation timeSet the preliminary rotation time for fusing when thepower is turned on.
*19 Fusing initial rotation control after printing smallsize
Change this setting to "1" when the thermal offset atedges of the paper occurs after feeding the small-sizepaper (216mm or less in width). However, changing this setting to "1" within 4 min-utes after the printing stop of the previous job makesthe fusing initial rotation time longer.
Mode 7-7
Normal 0
Side 2 only 1
Mode 8-1 8-0
Standard (*190/170) 0 0
Lighter (*167/137) 0 1
Lightest (*142/112) 1 0
Standard (*190/170) 1 1
* 0 (white) to 255 (black) represent density withinthe image density range. Numbers representeach image density at the line speed 460mm/s,290mm/s from left.
Mode 8-3 8-2
Low temperature 0 0
Low/normal temperature 0 1
Low/normal/high temper-ature
1 0
No preparatory rotation 1 1
Mode 8-5 8-4
180 seconds 0 0
300 seconds 0 1
60 seconds 1 0
0 second 1 1
Mode 8-7
Disable 0
Enable 1
9. SERVICE
44
biz
hu
b P
RO
95
0
9. SERField Service Ver.2.0 Sep. 2009
*20 Message switchoverSet a message displayed on the operation boardwhen the key counter, coin vendor and the copy card
are used.
*21 Copy quantity limitSet this when the number of copies for 1 job is lim-ited.
*22 Image memory usable areaChanges the usable area of DRAM (256 MB) on theoverall control board (OACB) and hard disk (HDD1). Compression memory is used within the memoryarea of compressed image data, and expansionmemory is used for page memory of expanded imagedata. There are 2 types of image memory; DRAM onOACB and hard disk/1 (30 GB of total 160 GB isused). DRAM is used by priority. If hard disk/1 is dam-aged and memory overflow occurs during scanningor transferring data from PC, increase compressionmemory. If memory overflow occurs before printingstarts, increase expansion memory.
Mode 9-3 9-2
Please insert key counter 0 0
Please insert copy card 0 1
Please insert coin 1 0
Please insert key counter 1 1
Mode 9-7 9-6 9-5 9-4
No limit 0 0 0 0
1 print 0 0 0 1
3 prints 0 0 1 0
5 prints 0 0 1 1
9 prints 0 1 0 0
10 prints 0 1 0 1
20 prints 0 1 1 0
30 prints 0 1 1 1
50 prints 1 0 0 0
99 prints 1 0 0 1
250 prints 1 0 1 0
No limit 1 0 1 1
No limit 1 1 0 0
No limit 1 1 1 0
No limit 1 1 1 1
Mode 10-1 10-0
Compression memory 132MBPage memory 36MB
0 0
Compression memory 104MBPage memory 64MB
0 1
Compression memory 220MBPage memory 36MB
1 0
Compression memory 24MBPage memory 26MB
1 1
VICE MODE
245
MODE
2
Field Service Ver.2.0 Sep. 2009b
izh
ub
PR
O 9
50
*23 Definition change of the large size paper incounter control
Set a large paper size in DIPSW4-7 and 8-6. Default
varies depending on the destination.
Refer to the following table about the default for each destination.
*24 Original size detection switchover 3Set the smallest possible original size to be detectedby DFThe default setting is different depending on the area.Metric: A5SInch: 51/2 x 81/2S
Mode 10-4 10-3
A3, 11 x 17, Custom size/Wide paper is 391mm or longer in the sub scan direction.
0 0
Small size only 0 1
A3, 11 x 17, 8 1/2 x 14, B4, 8K, custom size/wide paper is 331mm or longer in the sub scan direction.
1 0
A3, 11 x 17, 8 1/2 x 14, B4, 8K, F4, custom size/wide paper is 298mm or longer in the sub scan direction.
1 1
Destination Counter Large-size count number DipSW initial setting
Standard-size paper Custom paper/Wide Paper A3/ 11 x 17 B4/ 8 1/2 x 14
Japan Maintenance Counter 1 1 1 DipSW 8-6 : 0
Total Counter 1 1 1 DipSW 4-7 : 0 DipSW 10-4 : 0 DipSW 10-3 : 0
Europe Maintenance Counter 1 1 1 DipSW 8-6 : 0
Total Counter 1 1 1 DipSW 4-7 : 0 DipSW 10-4 : 0 DipSW 10-3 : 0
North Amer-ica
Maintenance Counter 1 1 1 DipSW 8-6 : 0
Total Counter 2 1 2 (391mm or longer)
DipSW 4-7 : 1 DipSW 10-4 : 0 DipSW 10-3 : 0
Other Maintenance Counter 1 1 1 DipSW 8-6 : 0
Total Counter 2 2 2 (331mm or longer)
DipSW 4-7 : 1 DipSW 10-4 : 1 DipSW 10-3 : 0
Mode 13-4 13-3
A5S 0 0
B6S 0 1
51/2 x 81/2S 1 0
— 1 1
9. SERVICE
46
biz
hu
b P
RO
95
0
9. SERField Service Ver.2.0 Sep. 2009
*25 Original size detection switchover 4Set the definition of the F4 size.The default setting is different depending on the area.
Metric: 8 x 13Inch: 81/2 x 14
*26 Transfer assist sheet pressure control on side1The transfer assist sheet pressure normally works onthe side2 of paper, but change this setting when itneeds to work on the front side. However, changingit to "1" (with pressure) increases the paper duststacking to the transfer/separation charger and itneeds to clean frequently.
Note
• It does not press on the tab paper even
when this setting is changed to "1" (with
pressure).
*27 Number of paper that can be stapledSet the Staple number allowed.
*28 Finishing option alarm stopThe alarm stop indicates a condition in which the fol-lowing full detection function:FS tray upper limit, tray paper full, folding full, PK/ZUpunch full, TU scraps full, and stacker full
Mode 13-7 13-6 13-5
8 x 13 0 0 0
81/4 x 13 0 0 1
81/8 x 131/4 0 1 0
81/2 x 13 0 1 1
81/2 x 14 1 0 0
Not used 1 0 1
Not used 1 1 0
Not used 1 1 1
Mode 15-0
No pressure 0
With pressure 1
Mode 15-2 15-1
100 sheets or 50 sheets 0 0
95 sheets or 45 sheets 0 1
90 sheets or 40 sheets 1 0
85 sheets or 35 sheets 1 1
Mode 15-4 15-3
Stops immediately after detection
0 0
Stops at a break between print set after detection
0 1
Does not stop while printing 1 0
Stops only when detecting the main tray full alarm
1 1
VICE MODE
247 1
MODE
2
Field Service Ver.2.0 Sep. 2009b
izh
ub
PR
O 9
50
*29 Non-image area erase mode judge levelThis setting should be changed if auto erase is car-ried out incorrectly when "Non-image area erase
mode" is used.
*30 Summer time settingSet the time difference of the summer time that is setin the set-up menu mode.
*31 Density selection at scanning tab paperSet the shading of the texture of index paper.
Mode 16-6 16-5
Standard 0 0
Correspond to dark origi-nal
0 1
Correspond to light inter-ference
1 0
Not used 1 1
Mode 17-3 17-2 17-1 17-0
0 minute 0 0 0 0
10 minutes 0 0 0 1
20 minutes 0 0 1 0
30 minutes 0 0 1 1
40 minutes 0 1 0 0
50 minutes 0 1 0 1
60 minutes 0 1 1 0
70 minutes 0 1 1 1
80 minutes 1 0 0 0
90 minutes 1 0 0 1
100 minutes 1 0 1 0
110 minutes 1 0 1 1
120 minutes 1 1 0 0
130 minutes 1 1 0 1
140 minutes 1 1 1 0
150 minutes 1 1 1 1
Mode 17-6 17-5 17-4
Brightness level 80 0 0 0
Brightness level 40 (Lightest)
0 0 1
Brightness level 60 0 1 0
Brightness level 100 0 1 1
Brightness level 120 1 0 0
Brightness level 160 1 0 1
Brightness level 200 1 1 0
Brightness level 255 (Darkest)
1 1 1
9. SERVICE
48
biz
hu
b P
RO
95
0
9. SERField Service Ver.2.0 Sep. 2009
*32 Fusing temperature settingWhen a problem (insufficient fusibility, large papercurling amount) is found with fusibility, set the fusing
set temperature.Temperature up: Suppress insufficient fusing and fus-ing wind-up jam.Temperature down: Suppress exited paper curlingand paper ruffling.
*33 Maximum black band width (when connectingRC)
Sets the maximum width of the black band in blackband creation control. This function is enable onlywhen RC is connected.
*34 Image scanning area with "Page margin" func-tion
Normal: Compare the original size and the transferpaper size, the smaller one is to be the imagearea.
Original priority:Original size is to be the image area.
*35 Fusing heat roller temperature control The setting is 200°C for the hard roller since highcontrol temperature of the fusing heat roller keeps thecurling ability and fusibility. When printing on the smooth paper with the softroller, specify the control temperature of the fusingheat roller to 130°C since the gloss unevennessstands. Furthermore, when the fusibility has a priority in print-ing on the thick paper with the soft roller, specify it to200°C.
Mode 19-3 19-2 19-1 19-0
Standard 0 0 0 0
Standard +5°C 0 0 0 1
Standard +10°C 0 0 1 0
Standard +15°C 0 0 1 1
Standard -5°C 0 1 0 0
Standard -10°C 0 1 0 1
Standard -15°C 0 1 1 0
Standard -20°C 0 1 1 1
Standard -25°C 1 0 0 0
Standard -30°C 1 0 0 1
Standard -35°C 1 0 1 0
Standard -40°C 1 0 1 1
Standard -45°C 1 1 0 0
Standard -50°C 1 1 0 1
Standard -55°C 1 1 1 0
Standard -60°C 1 1 1 1
Mode 19-7 19-6
20mm 0 0
10mm 0 1
5mm 1 0
Follows the DIPSW 6-3 /4 settings
1 1
Mode 20-1
Normal 0
Original priority 1
Mode 21-2
200°C 0
130°C 1
VICE MODE
249
MODE
2
Field Service Ver.2.0 Sep. 2009b
izh
ub
PR
O 9
50
*36 Number of punch holesWhen changing this setting, the inhibitions of thepunch operation by paper sizes are also changed.
And, the punch hole screen displayed on the opera-tion board is also changed.
*37 Toner concentration of developer selectionChange developing roller rotation and toner density ofdeveloper (toner and carrier ratio) to change only tonerdensity of developer without changing image density.If increasing toner density of developer resulted inimage background, decrease toner density. If lighten-ing image in other DIPSW (27-2/3) resulted in whitespot on the solid section, increase toner density.
Note
• After change the DIPSW, image density does
not appear as the setting value until printing
about 500 prints because it need to add toner
to increase toner density of developer or
need to consume toner to reduce it.
• As one of the method to change the image
density without changing the toner density,
choosing [2 Function Setting] [3 Density Set-
ting] [4 Image Density Selection] on utility
mode can change the density keeping the
quality.
*38 Z-fold output number limitSet the upper limit number of sheets that can beexited to the FS main tray while in the Z-folding.
*39 Z-fold + Staple output number limitSet the upper limit number of sheets that can beexited to the FS main tray while in the Z-folding + sta-ple.
Mode 22-2 22-1
2 holes (in Japan) 0 0
3 holes (in inch system) 0 1
4 holes (in AB system) 1 0
— 1 1
Mode 23-4 23-3 23-2
Standard toner density 0 0 0
Approx. 0.5% down 0 0 1
Approx. 1.0% down 0 1 0
Approx. 1.5% down 0 1 1
Approx. 0.25% up 1 0 0
Approx. 0.5% up 1 0 1
Approx. 0.75% up 1 1 0
Approx. 1.0% up 1 1 1
Mode 24-5 24-4
50 sheets 0 0
40 sheets 0 1
30 sheets 1 0
20 sheets 1 1
Mode 24-7 24-6
5 sheets 0 0
8 sheets 0 1
10 sheets 1 0
3 sheets 1 1
9. SERVICE
50
biz
hu
b P
RO
95
0
9. SERField Service Ver.2.0 Sep. 2009
*40 Transfer assist control size switchover
NOTE
• Be sure to set this setting to be itemized
when itemizing the transfer assist sheet.
*41 Paper weight, process speed switch table Switches the control temperature of fusing and thetable of the process speed.
*42 Image density selection (toner control patch density)Changes the image density by setting the developingbias for the toner control patch formed on the drumto determine the toner density.
Note
• After changing the DIPSW, image density
does not appear as the setting value until
printing about 500 prints because it needs to
add toner to increase the toner density of
developer or consume toner to reduce it.
• Using this setting alone may cause image
background or toner spillage. Be sure to use
together with DIPSW23-2/3/4 (toner density
of developer) approx. 0.5% down or 1.0%
down.
• There are two kinds of DIPSWs to lighten
image density: laser PWM (5-2/3) and toner
control patch density (27-2/3). For the priority
of adjustment, adjust in the following order.
1) Laser PWM
2) Toner control patch density: approx. 0.5%
down
Using this setting alone may cause white
spots on the solid section. Be sure to use
together with DIPSW23-2/3/4 (toner den-
sity of developer) approx. 0.25% up or
0.5% up.
Mode 26-1 26-0
297mm or more 0 0
Between 279mm and 297mm
0 1
No transfer assist 1 0
Individual support 1 1
Mode 27-0
Paper feed ability preference (for Japan)
0
Productivity preference (for the other countries) (Enable only for 27-1-1 (hard roller))
1
Mode 27-3 27-2
Standard 0 0
Approx. 0.5% up 0 1
Approx. 1.0% up 1 0
Approx. 0.5% down 1 1
VICE MODE
251
MODE
2
Field Service Ver.2.0 Sep. 2009b
izh
ub
PR
O 9
50
*43 Image shift when outputting the custom sizeprint job
Image shift occurs depending on the paper size when
sending the custom size image as the print job. (The output is different from the thumbnail displayedimage).
Mode 28-4
Paper standard 0
Paper size > Image: normal
Paper size Image: Image shift
Image standard 1
Paper size > Image: normal
Paper size Image: normal
ABCDEFABCDEFABCDEF
CDEFGHCDEFGHCDEFGH
ABCDEFGHABCDEFGHABCDEFGHABCDEFGHABCDEFGHABCDEFGH
57gaf3c030na
[Normal] [Image Shift]
[Image]
Main scan direction
sub
scan
dire
ction
9. SERVICE
52
biz
hu
b P
RO
95
0
9. SERField Service Ver.2.0 Sep. 2009
*44 EL2 light volume switchover at the trailing edgeof paper
This setting reduces the transfer repelling by adjusting
the light volume of the transfer exposure lamp (EL2)when the transfer repelling occurs at the trailing edgeof paper with the half tone image while using the spe-cific paper such as user paper.
NOTE
• Conduct the setting according to instructions
of KMBT field support section.
*45 Printer input delay control Prevents the memory overflow by delaying the datainput time when it occurs in printer job.
*46 Automatic change of tray setting names
*47 Overwrite all HDD data NOTESW to all HDD data to be deleted when throw-ing the machine away.
NOTE
• This mode is used when disposing the
machines. By executing this function, all data
stored in the HDD is deleted and the machine
becomes inoperable.
*48 TIFF direct print Paper size for APS (F4)
Mode 29-6 29-5 29-4
The same level as the image section
0 0 0
Image section - 1 level 0 0 1
Image section - 2 level 0 1 0
Image section - 3 level 0 1 1
Image section - 4 level 1 0 0
Image section - 1 level 1 0 1
Image section - 1 level 1 1 0
Image section - 1 level 1 1 1
Mode 31-3 31-2
Without delay control 0 0
Delay control from 10% left
0 1
Delay control from 20% left
1 0
Delay control from 30% left
1 1
Mode 38-4
Automatically changes the name to the name of selected paper type, when paper type, paper weight, color, and punch settings are changed.
0
Name= Automatically changed to the same name as the paper name only when changing the paper kind
1
Mode 40-1
Restrict 0
Allow 1
Mode 42-2 42-1
8 x 13 0 0
8 1/2 x 13 0 1
8 1/4 x 13 1 0
8 1/8 x 13 1/4 1 1
VICE MODE
253 1
MODE
2
Field Service Ver.2.0 Sep. 2009b
izh
ub
PR
O 9
50
*49 TIFF direct print Resolution settingWhen "TIFF direct print" is used, all of TIFF data isprinted by 600dpi resolution. For example, when
200dpi resolution of A4 size TIFF data is printed by"direct print",In the case of 0 : The resolution of the TIFF data is
converted into 600dpi, it isreduced and printed.
In the case of 1 : The TIFF data is not reduced and itis printed correctly.
*50 Visual Counter Master counter value read-offintervals
Mode 42-5
Resolution priority(Changed 600dpi)
0
Output size priority 1
Mode 46-1 46-0
Every 10 minutes 0 0
Every 1 minute 0 1
Not acquisition 1 0
Every 1 hour 1 1
9. SERVICE
54
biz
hu
b P
RO
95
0
9. SERField Service Ver.2.0 Sep. 2009
9.9.2 Telephone Number Setting
Set the telephone number and FAX number of the service center displayed when malfunction occurs.
A. Procedure
9.9.3 M/C Serial Number Setting
Set and display the serial number of the main body and options.
Caution
• Never change the serial number of the main body. Otherwise, the fusing temperature abnormality
may occur.
A. Procedure
Note
• When the input data is incorrect, a notice screen appears. Press [OK] to close the screen and
input data again.
• The serial number of the main body cannot be changed.
1. "Service mode menu screen"Press [07 System Setting].
2. "System Setting menu screen"Press [02 Telephone Number Setting].
3. "Customer support TEL/FAX setting screen"Press either the [Service Center Tel (16)] or the [Service Center Fax (16)] you want to set.
4. Enter the telephone number or FAX number you register through the numeric keys.
NOTE
• When a number is less than 16 digits, be sure to use hyphen etc to fill up the blanks.
5. Press [OK] to register data.Press [Cancel] to cancel the setting you entered.
1. "Service mode menu screen"Press [07 System Setting].
2. "System Setting menu screen"Press [03 M/C Serial Number Setting].
3. "Serial number setting mode screen"Press the key for the option you want to set, and enter the serial number through the numeric keys.
4. Press [OK] to register data.Press [Cancel] to cancel the setting you entered.
VICE MODE
255
MODE
2
Field Service Ver.2.0 Sep. 2009b
izh
ub
PR
O 9
50
9.9.4 Setting Date Input
Set the starting date of the total counter that is displayed on the utility mode.When setting the DIPSW 16-4 to 1, the starting date of the total counter is not displayed.
A. Procedure
1. "Service mode menu screen"Press [07 System Setting].
2. "System Setting menu screen"Press [04 Setting Date Input].
3. "Setting date input screen"Enter the new date through the numeric keys.
4. Press [OK] to update data.Press [Cancel] to cancel the setting you updated.
9. SERVICE
56
© 2009 KONICA MINOL T A BUSINESS TECHNOLOGIES, INC .
Printed in Japan CCA0Y5-M-FE2- 0000
Use of this manual should be strictly supervised to avoid disclosu r e of confidential information .