CY6251 ENGINEERING CHEMISTRY - II
1
SCE Dept.of S & H
A Course Material on
ENGINEERING CHEMISTRY II
By Mrs. K. MABEL HEBSUBA/ ASSISTANT PROFESSOR
Mr. G. DHINESH/ ASSISTANT PROFESSOR Mr. J. MUHAMED ALI/ ASSISTANT PROFESSOR & Mrs. S. VIJAYA LAKSHMI/ ASSISTANT PROFESSOR
DEPARTMENT OF SCIENCE AND HUMANITIES SASURIE COLLEGE OF ENGINEERING
VIJAYAMANGALAM – 638 056
CY6251 ENGINEERING CHEMISTRY - II
2
SCE Dept.of S & H
QUALITY CERTIFICATE
This is to certify that the e-course material Subject Code : CY6251 Subject : Engineering Chemistry II Class : I Year being prepared by us and it meets the knowledge requirement of the university curriculum.
Signature of the Author
Name: K. Mabel Hebsuba, G. Dhinesh
J. Mohammed Ali & S. Vijaya Lakshmi
Designation: Assistant Professor
This is to certify that the course material being prepared by Mrs.K. Mabel Hebsuba, G. Dhinesh, J. Muhamed Ali & S. Vijaya Lakshmi is of adequate quality. He has referred more than five books amount them minimum one is from aborad author.
Signature of HD Name:
SEAL
CY6251 ENGINEERING CHEMISTRY - II
3
SCE Dept.of S & H
TABLE OF CONTENTS
S.NO TITLE PAGE NO
1 UNIT I WATER TECHNOLOGY 8
1.1 Introduction 8
1.2 Hard water and soft water 8
1.3 Boiler Feed water 8
1.3.1 Formation of deposits in steam boilers and Heat exchangers. 9
1.3.2 Caustic embrittlement 10
1.3.3 Boiler corrosion 11
1.3.4 Priming and Foaming 13
1.4 Softening or conditioning Methods 14
1.4.1 Zeolite or Permutit process 14
1.4.2 Ion-Exchange (or) De- ionization (or) Demineralisation Process 14
1.5 Internal Treatment (or) Internal Conditioning (or) Boiler Compounds 14
1.6 Desalination of Brackish water 20
1.6.1 Reverse Osmosis (R.O) 20
1.7 Glossary 21
2 UNIT II ELECTROCHEMISTRY AND CORROSION 22
2.1 Introduction 22
2.1.1 Types of cells 23
2.2 Electrochemical Cells 26
2.2.1 Reversible and Irreversible cells 27
2.3 Electrode Potential 28
2.3.1 Reduction Potential 28
2.3.2 Single electrode Potential 29
2.3.3 Standard electrode Potential 30
2.3.4 Measurement of Standard electrode Potential 30
2.4 EMF of Cell 35
2.4.1 Measurement of EMF of cell 36
2.4.2 Applications of EMF measurement 36
2.5 Electrochemical Series 36
2.5.1 Significance of EMF series 36
2.6 Nernst Equation 38
2.6.1 Nernst equation for reversible cell 39
2.6.2 Problems based on Nernst equation 40
2.7 Corrosion 40
2.7.1 Consequences of corrosion 40
2.8 Types of Theories of Corrosion 40
2.8.1 Dry or Chemical corrosion 41
2.8.2 Wet or electrochemical corrosion 42
2.9 Factors influencing the rate of corrosion 47
2.9.1 Nature of the metal 47
2.9.2 Nature of the environment 47
CY6251 ENGINEERING CHEMISTRY - II
4
SCE Dept.of S & H
2.10 Corrosion Control 48
2.10.1 By modifying metal 48
2.10.2 BY modifying the environment 51
2.11 Paints 52
2.11.1 Characteristics of a good paint 52
2.11.2 Constituents and their functions of paints 52
2.12 Metallic Coatings 53
2.12.1Electroplating 53
2.12.2 Electroless Plating 54
2.13 Glossary 56
3 UNIT – III ENERGY SOURCES 57
3.1 Introduction 57
3.2 Nuclear Energy 57
3.2.1 Nuclear Fission 57
3.2.2 Nuclear fusion 57
3.2.3 Nuclear chain reaction 57
3.3 Nuclear reactor 59
3.3.1 Light water Nuclear Reactor 59
3.3.2 Breeder Reactor 60
3.4 Solar Energy 61
3.4.1 Solar energy conversion 61
3.4.2 Solar cell 61
3.4.3 Application of Solar Cells 61
3.5 Wind Energy 63
3.5.1 Wind Mill 63
3.6 Batteries 64
3.6.1 Types of batteries 64
3.6.2 Alkaline Battery 64
3.6.3 Lead Storage Battery 65
3.6.4 Nickel-Cadmium Battery 65
3.6.5 Lithium Battery 66
3.7 Fuel Cells 68
3.7.1 Hydrogen Oxygen Fuel Cell 68
3.8 Glossary 70
4 UNIT – IV ENGINEERING MATERIALS 71
4.1 Introduction 71
4.2 Abrasives 71
4.2.1 Properties of Abrasives 71
4.2.2 Classification of Abrasives 71
4.2.3 Applications of Abrasives 71
4.3 Refractories 72
4.3.1 Characteristics of Refractories 72
4.3.2 Classification of Refractories 73
4.3.3 Properties of Refractories 73
4.3.4 Manufacturing of Refractories 74
4.4 Portland Cement 74
CY6251 ENGINEERING CHEMISTRY - II
5
SCE Dept.of S & H
4.4.1 Chemical composition of Portland cement 74
4.4.2 Manufacturing methods 75
4.4.3 Setting and hardening 78
4.4.4 Other types of cements 77
4.5 Glass 77
4.5.1 Properties of glass 77
4.5.2 Manufacturing of glass 78
4.5.3 Types and uses of glass 78
4.6 Glossary 80
5 UNIT V FUELS AND COMBUSTION 82
5.1 Definition 82
5.1.1 Characteristics for good fuel 82
5.2.1 Calorific value: 82
5.2.2 Gross or high calorific value (gcv) 82
5.2.3 Net or lower calorific value(ncv) 82
5.2.4 Theoretical calculation of calorific value ( dulong‟s formula) 83
5.3 Solid fuel 83
5.3.1 Advantages of solid fuels: 83
5.3.2 Disadvantages of solid fuels: 83
5.4 Coal 83
5.4.1 Proximate analysis & 5.4.2 significance of proximate analysis 83
5.5 Carbonization of metallurgical coke 84
5.5.1 Metallurgical coke 84
5.5.2 Otto-Hoffman‟s method 84
5.5.3 Recovery of by-products 85
5.5.4 Advantages of otto hoffman‟s process 85
5.6 Liquid fuels 85
5.6.1 Advantages of liquid fuels, disadvantages of liquid fuels 85
5.6.2 Petroleum 86
5.6.3 Refining of petroleum or crude oils 86
5.7. Knocking 87
5.7.1 Causes of knocking in S.I (petrol) engines 87
5.7.2 Improvement of anti knock characteristics 87
5.7.3 Octane number or octane rating 87
5.7.4Anti-knock agent 87 5.7.5Causes of knocking in C.I (diesel) engines 88
5.7.6 Cetane number or cetane rating 88
5.7.8 Diesel index 88
5.8. Hydrogenation of coal 89
5.8.1 Bergius process (indirect method) 89
5.8.2 Fischer-tropics process (indirect method) 90
5.9 Gaseous fuels 90
5.9.1. Compressed natural gas (CNG) 91
5.9.2 Producer gas 91
5.9.3. Water gas 92
5.9.4 LPG- liquefied petroleum gas 93
CY6251 ENGINEERING CHEMISTRY - II
6
SCE Dept.of S & H
5.10 GLOSSARY 97
6 QUESTION BANK 98
7 UNIVERSITY QUESTIONS 158
CY6251 ENGINEERING CHEMISTRY-II L T P C 3 0 0 3 OBJECTIVES:
To make the students conversant with boiler feed water requirements, related problems and
water treatment techniques.
Principles of electrochemical reactions, redox reactions in corrosiion of materials and methods
for corrosion prevention and protection of materials.
Principles and generation of energy in batteries, nuclear reactors, solar cells, wind mills and fuel cells.
Preparation, properties and applications of engineering materials.
Types of fuels, calorific value calculations, manufacture of solid, liquid and gaseous fuels.
UNIT I WATER TECHNOLOGY 9 Introduction to boiler feed water-requirements-formation of deposits in steam boilers and heat exchangers- disadvantages (wastage of fuels, decrease in efficiency, boiler explosion) prevention of scale formation -softening of hard water -external treatment zeolite and demineralization- internal treatment- boiler compounds (phosphate, calgon, carbonate, colloidal) - caustic embrittlement-boiler corrosion-priming and foaming- desalination of brackish water –reverse osmosis. UNIT II ELECTROCHEMISTRY AND CORROSION 9 Electrochemical cell - redox reaction, electrode potential- origin of electrode potential- oxidation potential- reduction potential, measurement and applications - electrochemical series and its significance - Nernst equation (derivation and problems). Corrosion- causes- factors- types-chemical electrochemical corrosion (galvanic, differential aeration), corrosion control - material selection and design aspects - electrochemical protection – sacrificial anode method and impressed current cathodic method. Paints- constituents and function. Electroplating of Copper and electroless plating of nickel. , UNIT III ENERGY SOURCES 9 Introduction- nuclear energy- nuclear fission- controlled nuclear fission- nuclear fusion- differences between nuclear fission and fusion- nuclear chain reactions- nuclear reactor power generatorclassification of nuclear reactor- light water reactor- breeder reactor- solar energy conversion- solar cells- wind energy. Batteries and fuel cells:Types of batteries- alkaline battery- lead storage batterynickel- cadmium battery- lithium battery- fuel cell H2 -O2 fuel cell- applications. UNIT IV ENGINEERING MATERIALS 9
CY6251 ENGINEERING CHEMISTRY - II
7
SCE Dept.of S & H
Abrasives: definition, classification or types, grinding wheel, abrasive paper and cloth. Refractories: definition, characteristics, classification, properties – refractoriness and RUL, dimensional stability, thermal spalling, thermal expansion, porosity; Manufacture of alumina, magnesite and silicon carbide, Portland cement- manufacture and properties - setting and hardening of cement, special cement waterproof and white cement–properties and uses. Glass - manufacture, types, properties and uses. UNIT V FUELS AND COMBUSTION 9 Fuel: Introduction- classification of fuels- calorific value- higher and lower calorific values- coalanalysis of coal (proximate and ultimate)- carbonization- manufacture of metallurgical coke (Otto Hoffmann method) - petroleum- manufacture of synthetic petrol (Bergius process)- knocking- octane number - diesel oil- cetane number - natural gas- compressed natural gas(CNG)- liquefied petroleum gases(LPG)- producer gas- water gas. Power alcohol and bio diesel. Combustion of fuels: introduction- theoretical calculation of calorific value- calculation of stoichiometry of fuel and air ratioignition temperature- explosive range - flue gas analysis (ORSAT Method). TOTAL: 45 PERIODS OUTCOMES: The knowledge gained on engineering materials, fuels, energy sources and water treatment techniques will facilitate better understanding of engineering processes and applications for further learning. TEXT BOOKS: 1. Vairam S, Kalyani P and SubaRamesh.,“Engineering Chemistry”., Wiley India PvtLtd.,New Delhi., 2011 2. Dara S.S and Umare S.S. “Engineering Chemistry”, S. Chand & Company Ltd., New Delhi , 2010 REFERENCES: 1. Kannan P. and Ravikrishnan A., “Engineering Chemistry”, Sri Krishna Hi-tech Publishing Company Pvt. Ltd. Chennai, 2009. 2. AshimaSrivastava and Janhavi N N., “Concepts of Engineering Chemistry”, ACME Learning Private Limited., New Delhi., 2010. 3. RenuBapna and Renu Gupta., “Engineering Chemistry”, Macmillan India Publisher Ltd., 2010. 4. Pahari A and Chauhan B., “Engineering Chemistry”., Firewall Media., New Delhi., 2010
CY6251 ENGINEERING CHEMISTRY - II
8
SCE Dept.of S & H
UNIT I
WATER TECHNOLOGY
1.1 INTRODUCTION
Water is essential for the existence of human beings, animals and plants.
Though 80% of the earth‟s surface is occupied by water, less than 1% of the
water is available for ready use.
The main sources of water are
Rain
rivers and lakes (surface water)
wells and springs (ground water)
sea water
Among the above sources of water, rain water is the purest form of water but it is very
difficult to collect whereas sea water is the most impure form.
Thus, surface and ground water are normally used for industrial and
domestic purposes. Such water must be free from undesirable impurities.
“The process of removing all types of impurities from water and making it
fit for domestic or industrial purposes are called water treatment.” Before
treating water one must know the nature as well as the amount of impurities.
1.2 HARD WATER AND SOFT WATER
Hard Water
“Water which does not produce lather with soap solution, but
produces white precipitate is called hard water”.
This is due to the presence of dissolved Ca and Mg salts.
2C17 H 35 COONa + Ca ++
→ (C17 H 35 COO) 2 Ca +2Na+
Water soluble Water insoluble
Soft Water
“Water which produces lather readily with soap solution is called soft water.”
This is due to the absence of Ca and Mg salts.
1.3 BOILER FEED WATER
In Industry, one of the chief uses of water is generation of steam by
boilers. The water fed into the boiler for the production of steam is called
boiler feed water.
CY6251 ENGINEERING CHEMISTRY - II
9
SCE Dept.of S & H
Requirements of boiler feed water
It should have zero hardness.
It must be free from dissolved gases like O2, CO2, etc.
It should be free from suspended impurities.
It should be free from dissolved salts and alkalinity
It should be free from turbidity and oil.
It should be free from hardness causing and scale forming constituents like
Ca and Mg salts.
1.3.1 Formation of deposits (Scales and Sludges) in boilers and heat exchangers
In a boiler, water is continuously converted into steam. Due to this continuous
evaporation of water, the concentration of soluble matters increases progressively. Then
the salts separating out from the solution in the order of their solubility, the lease
soluble ones
separating out first.
(i) Sludge
If the precipitate is loose and slimy it is called
sludges.
Sludges are formed by substances like MgCl2, MgCO3, MgSO4
and CaCl2.
They have greater solubilities in hot water than
cold water.
( i i ) Scale
If the precipitate forms hard and adherent coating on the inner walls of the
boiler, it is called scale.
Scales are formed by substances like Ca (HCO3)2, CaSO4 and
Mg(OH) 2.
CY6251 ENGINEERING CHEMISTRY - II
10
SCE Dept.of S & H
Disadvantages of Scale Formation
(i) Wastage of fuels
Scales have a low thermal conductivity, so the rate of heat transfer from
boiler to inside water is greatly decreased. In order to provide a supply of
heat to water, excessive or over-heating is done. This causes increase in fuel
consumption. The wastage of fuel depends upon the thickness and the nature of
scale.
(ii) Decrease in efficiency
Scales sometimes deposit in the valves and condensers of the boiler and choke them
partially. This results in decrease in efficiency of the boiler.
(iii) Boiler explosion When thick scales crack due to uneven expansion, the water comes suddenly in
contact
with over-heated iron plates. This causes in formation of a large amount of steam
suddenly. So sudden high-pressure is developed, which may even cause
explosion of the boiler.
Prevention of scale formation
At the initial stage, scales can be removed using scraper, wire brush etc.
If scales are brittle, they can be removed by thermal shocks.
If the scales are loosely adhering, they can be removed by frequent blow
down operation.
1.3.2 Caustic Embrittlement Caustic embrittlement is a form of corrosion caused by a high concentration of
sodium
Hydroxide in the boiler feed water.
It is characterized by the formation of irregular intercrystalline cracks on the boiler
metal, particularly at places of high local stress such as bends and joints.
Causes of caustic embrittlement
Boiler water usually contains a small amount of Na2CO3. In high pressure boilers,
Na2CO3 undergoes hydrolysis to produce NaOH.
Na 2 CO 3 + H 2 O → 2NaOH
+CO2
This NaOH flows into the minute hairline cracks present on the boiler material by
capillary action and dissolves the surrounding area of iron as sodium ferroate, Na2FeO2.
Fe + 2NaOH → Na 2 FeO 2
+H2
CY6251 ENGINEERING CHEMISTRY - II
11
SCE Dept.of S & H
This type of electrochemical corrosion occurs when the concentration of
NaOH is above 100 ppm. This causes embrittlement of boiler parts, particularly the
stressed parts like bends, joints, rivets, etc.
Caustic embrittlement can be prevented by
Using sodium phosphate as the softening agent instead of sodium carbonate.
Adding chemicals such as tannin, lignin to the boiler water. They block the
hairline cracks.
Adjusting the pH of the feed water carefully between 8 and 9.
1.3.3 Boiler Corrosion
Corrosion in boilers is due to the presence of
Dissolved oxygen
Dissolved carbon dioxide
Dissolved salts like magnesium chloride.
Dissolved oxygen
The presence of dissolved oxygen is responsible for corrosion in boilers. Water
containing dissolved oxygen when heated in a boiler, free oxygen is evolved, which
corrodes the boiler material.
4Fe + 6H2O + 3O2 → 4 Fe
(OH)3
Dissolved carbon dioxide
When water containing bicarbonates is heated, carbon dioxide is evolved which
makes the water acidic. Carbon dioxide dissolved in water forms carbonic acid. This
leads to intense local corrosion called pitting corrosion.
Ca(HCO3)2 → CaCO3 + H2O +
CO2
CO2 + H2O → H2CO3
Dissolved magnesium chloride
When water containing dissolved magnesium chloride is used in a boiler,
hydrochloric acid is produced. HCl attacks the boiler in a chain-like reaction producing
hydrochloric acid again and again which corrodes boiler severely.
MgCl2 + 2H2O → 2HCl + Mg (OH)2
CY6251 ENGINEERING CHEMISTRY - II
12
SCE Dept.of S & H
Fe + 2 HCl → FeCl2 + H2
FeCl2 + 2H2O → Fe (OH)2 + 2 HCl
Corrosion by HCl can be avoided by the addition of alkali to the boiler water.
Prevention of boiler corrosion
Removal of dissolved oxygen and carbon dioxide can be done either chemically or
mechanically.
Chemical method For the removal of dissolved oxygen, sodium sulphite, hydrazines are used.
2Na2SO3 + O2 → 2Na2SO4
N2H4 + O2 → N2 + 2H2O
Hydrazine is the ideal compound for the removal of dissolved O2 as it forms
only water and inert nitrogen gas during the reaction.
Dissolved CO2 is removed by the addition of ammonium hydroxide.
2NH4OH + CO2 → (NH4)2CO3 + H2O
Mechanical method
Oxygen along with carbon dioxide can be removed mechanically by the de-
aeration method
In this method, water is allowed to fill in slowly on the perforated plates fitted
inside the tower.
To reduce the pressure inside the tower, the de-aerator is connected to a vacuum
pump. The sides of the tower are heated by means of a steam jacket. This is based on
the principle that the solubility of a gas in water is directly proportional to pressure and
inversely proportional to temperature.
CY6251 ENGINEERING CHEMISTRY - II
13
SCE Dept.of S & H
High temperature, low pressure and a large exposed surface, reduces the
dissolved gases (O2 and CO 2) in water.
The water flows down through a number of perforated plates and this arrangement
exposes a large surface of water for de-aeration.
1.3.4 Priming and Foaming
During the production of steam in the boiler, due to rapid boiling, some droplets of
liquid water are carried along with steam. Steam containing droplets of liquid water is
called wet steam.
These droplets of liquid water carry with them some dissolved salts and suspended
impurities. This phenomenon is called carry over. It occurs due to priming and foaming.
Priming
Priming is the process of production of wet steam. Priming is caused by
High steam velocity.
Very high water level in the boiler.
Sudden boiling of water.
Very poor boiler design.
Prevention
Priming can be controlled by
Controlling the velocity of steam.
Keeping the water level lower.
Good boiler design.
Using treated water.
Foaming
The formation of stable bubbles above the surface of water is called foaming.
These bubbles are carried over by steam leading to excessive priming.
Foaming is caused by the
Presence of oil and grease.
Presence of finely divided particles.
Prevention
Foaming can be prevented by
Adding coagulants like sodium aluminate, aluminium hydroxide.
Adding anti-foaming agents like synthetic polyamides.
CY6251 ENGINEERING CHEMISTRY - II
14
SCE Dept.of S & H
1.4 PREVENTION OF SCALE FORMATION (OR) SOFTENING OF
HARD WATER
The process of removing hardness – producing salts from water is known as
softening or conditioning of water. Since water is a source for industrial purpose. It is
mandatory to soften water to make it free from hardness producing substances,
suspended impurities and dissolved gases, etc.
Softening of water can be done by two
methods.
i) External treatment
ii) Internal treatment.
External Treatment or Conditioning
It involves the removal of hardness producing salts from the water before
feeding into the boiler. The external treatment can be done by the following
methods.
Zeolite (or) Permutit process
1.4.1 Zeolite (or) Permutit process
Zeolites are naturally occuring hydrated sodium aluminosilicate minerals. The
chemical formula is Na2O.Al2O3.XSiO2.YH2O. The synthetic form of zeolite is called
permutit and is represented by Na2Ze.
In this process the hard water is allowed to perlocate through sodium zeolite. The
sodium ions which are loosely held in this compound are replaced by Ca2+
and Mg2+
ions.
When zeolite comes in contact with hard water, it exchanges its sodium ions with
calcium and magnesium ions of hard water to form calcium and magnesium zeolites.
As sodium ions do not give any hardness to water, the effluent will be soft. The
exhausted zeolite is again regenerated by treated with 5 to 10 percent of sodium
chloride solution.
Na2Ze + Ca(HCO)2 CaZe + 2NaHCO3
CY6251 ENGINEERING CHEMISTRY - II
15
SCE Dept.of S & H
Na2Ze + Mg(HCO)2 MgZe + 2NaHCO3
Na2Ze + MgCl2 MgZe + 2NaCl
Na2Ze + CaCl2 CaZe + 2NaCl
Na2Ze + CaSO4 CaZe + Na 2SO4
Na2Ze + MgSO4 MgZe + Na 2SO4
Regeration
After some time zeolite gets exhausted. The exhausted zeolite is again regerated by
treating with 10%solution of NaCl.
CaZe + 2 NaCl → Na2Ze + CaCl2
MgZe + 2 NaCl → Na2Ze +MgCl2
Advantages
No sludge is formed during this process.
Water of nearly zero hardness is obtained.
This method is very cheap because the generated permutit can be used
again.
The equipment used is compact and occupies a small space.
Its operation is also easy.
The process can be made automatic and continuous.
Disadvantages
This process cannot be used for turbid and acidic water as they will
destroy the zeolite bed.
This treatment replaces only the cations, leaving all the anions like
CY6251 ENGINEERING CHEMISTRY - II
16
SCE Dept.of S & H
(HCO3)–
and(CO3)2–
in the soft water.
When such water is boiled in boilers, CO2 is liberated. Free CO2 is weakly
acidic in nature and extremely corrosive to boiler metal.
Na2CO3 + H2O→2NaOH + CO2
Due to the formation of sodium hydroxide, the water becomes alkaline
and can cause cause caustic embrittlement.
Water containing Fe, Mn cannot be treated, because regeneration is very
difficult.
This process cannot be used for softening brackish water. Because
brackish water also contains Na+
ions. So, the ions exchange reaction will
not take place.
1.4.2 Ion exchange or Demineralisation process
Ion exchange or demineralisation process removes almost all the ions (both anions
and cations) present in the hard water.
The soft water, produced by lime-soda and zeolite processes, does not contain
hardness producing Ca2+
and Mg2+
ions, but it will contain other ions like Na+, K
+, SO4
2–
, Cl–
etc.,
On the other hand demineralised (DM) water does not contain both anions and
cations. Thus a soft water is not demineralised water whereas demineralised water is soft
water.
This process is carried out by using ion exchange resins, which are long chain,
cross linked, insoluble organic polymers with a micro process structure. The functional
groups attached to the chains are responsible for the ion exchanging properties.
(i) Cation exchanger
Resins containing acidic functional groups (–COOH, – SO3H) are capable of
exchanging their H+
ions with other cations of hard water. Cation exchange resin
is represented as RH2.
Examples:
Sulphonated coals
Sulphonated polystyrene
R–SO3H; R–COOH ≡ RH2
(ii) Anion Exchanger
CY6251 ENGINEERING CHEMISTRY - II
17
SCE Dept.of S & H
Resins containing basic functional groups (–NH2, –OH) are capable of
exchanging their anions with other anions of hard water.
Anion exchange resin is represented as R (OH)2.
Examples:
Cross-linked quaternary ammonium salts.
Urea-formaldehyde resin.
R–NR3OH; R–OH; R–NH2 ≡ R (OH)2
Process
The hard water first passed through a cation exchange which absorbs all the
cations like Ca2+
, Mg2+
Na+, K
+, etc. present in the hard water.
RH2 + CaCl2 → RCa + 2HCl
RH2 + MgSO4 → RMg + H2SO4
RH + NaCl → RNa + HCl
The cation free water is then passed through a anion exchange column, which
absorbs all the anions like Cl–, SO4
2, HCO3
–, etc., present in the water.
R' (OH) 2 + 2HCl → R'Cl2 +
2H2O R'(OH) 2 + H2SO4 →
R'SO4 + 2H2O
The water coming out of the anion exchanger completely free from cations and
CY6251 ENGINEERING CHEMISTRY - II
18
SCE Dept.of S & H
anions. This water is known as demineralised water or deionised water.
Regeneration
When the cation exchange resin in exhausted, it can be regenerated by
passing a solution of dil.HCl or dil.H2SO4.
RCa + 2HCl → RH2 + CaCl2
RNa + HCl → RH + NaCl
Similarly, when the anion exchange resin is exhausted, it can be regenerated by
passing a solution of dil.NaOH.
R'Cl2 + 2 NaOH → R'(OH)2 + 2 NaCl
Advantages
The water is obtained by this process will have very low hardness.
Highly acidic or alkaline water can be treated by this process.
Disadvantages
The equipment is costly.
More explosive chemicals are needed for this process.
Water containing turbidity, Fe and Mn cannot be treated, because turbidity
reduces the output and Fe, Mn form stable compound with the resins
.
1.5INTERNAL TREATMENT
Internal treatment involves adding chemicals directly to the water in the boilers
for removing dangerous scale – forming salts which were not completely
removed by the external treatment for water softening. This method is used to
convert scale to sludge which can be removed by blow-down operation.
Calgon conditioning
Carbonate conditioning
Phosphate conditioning
Colloidal conditioning
Calgon conditioning
Calgon is sodium hexa meta phosphate with a
Composition Na2(Na4 (PO3)6). A highly soluble complex containing Ca is formed by
replacing the sodium ions and thus prevents their formation of scale forming salts
CY6251 ENGINEERING CHEMISTRY - II
19
SCE Dept.of S & H
like CaSO4. The reaction is as follows:
2CaSO 4 + Na 2 [Na 4 (PO3) 6] → Na 2 [Ca 2 (PO3) 6] + 2Na 2SO4
Since the complex is highly soluble there is no problem of sludge disposal.
Carbonate conditioning
Scale formation due to CaSO4 in low pressure boilers can be avoided by adding
Na2CO3 to the boilers.
CaSO4 + Na2 CO3 → CaCO3 + Na2SO4
The forward reaction is favored by increasing the concentration of CO32-
.CaCO3
formed can be removed easily.
Phosphate conditioning
In high pressure boilers, CaSO4 scale whose solubility decrease with increase of
temperature. Such scale can be converted into soft sludge by adding excess of
soluble phosphates.
3CaSO4 + 2Na3 PO4 → Ca3 (PO4)2 +2Na2SO4
There are three types of phosphates employed for this purpose.
Tri-sodium phosphate – Na3PO4 (too alkaline): used for too acidic water.
Di-sodium hydrogen phosphate – Na2HPO4 (weakly alkaline): Used for weakly
acidic water.Mono sodium di hydrogen phosphate NaH2PO4 (acidic) used for alkaline
acidic water.
Colloidal conditioning The colloidal conditioning agents are kerosene, agar-agar, gelatin, glue, etc. They
are Used in low pressure boilers. The colloidal substances convert scale forming
substance like CaCO3, CaSO4 into a Non-adherent, loose precipitate called
sludge, which can be removed by blow-down Operation.
1.6 DESALINATION OF BRACKISH WATER
Depending upon the quantity of dissolved solids, water is graded as
Fresh water has < 1000 ppm of dissolved solids. Brackish water has > 1000 but <
35,000 ppm of Dissolved solids.
Sea water has > 35,000 ppm of dissolved solids.
Water containing dissolved salts with a peculiar salty or brackish taste is
CY6251 ENGINEERING CHEMISTRY - II
20
SCE Dept.of S & H
called brackish water. It is totally unfit for drinking purpose. Sea water and brackish
water can be made available as drinking water through desalination process.
The removal of dissolved solids (NaCl) from water is known as
desalination process. The need for such a method arises due to the non-availability of
fresh water. Desalination is carried out either by electro dialysis or by reverse osmosis.
1.6.1 Reverse Osmosis
When two solutions of different concentrations are separated by a semi-permeable
membrane, flow of solvent takes place from a region of low concentration to high
concentration until the concentration is equal on both the sides. This process is
called osmosis.
The driving forces in this phenomenon are called osmotic pressure. If a
hydrostatic pressure in excess of osmotic pressure is applied on the higher
concentration side, the solvent flow reverses, i.e., solvent is forced to move from
higher concentration to lower concentration .This is the principle of reverse osmosis.
Thus, in reverse osmosis method pure water is separated from its dissolved solids.
sing this method pure water is separated from sea water. This process is also
known as super-titration. The membranes used are cellulose acetate, cellulose butyrate,
etc.
Advantages
The life time of the membrance is high.
It can be replaced within few minutes.
It removes ionic as well as non-ionic, colloidal impurities.
Due to simplicity low capital cost, low operating, this process is
used for converting sea water into drinking water
CY6251 ENGINEERING CHEMISTRY - II
21
SCE Dept.of S & H
1.7 Glossary
Hardness
Harness is the property or characteristics of water, which does not produce lather
with soap solution.
Soft water
Water which produces lather readily with soap solution is called soft water. Soft
water is free of calcium & magnesium salts.
Temporary hardness
Temporary hardness is due to the presence of bicarbonates of calcium and
magnesium. Since these salts can be easily removed by simple physical methods such as
boiling and filtering.
Permanent hardness
Permanent hardness is due to the presence of soluble chlorides and sulphates of
calcium and magnesium. These salts can be removed by chemical treatments only.
Alkalinity
Alkalinity of water is due to the presence of soluble hydroxide ( OH- ), carbonate (
CO32-
) and bicarbonate ( HCO3-) ions.
Boiler feed water
The water which is free from dissolved salts, dissolved gases, hardness, oils and
alkalinity is known as boiler feed water.
Sludge
The loose and slimy precipitate is called sludge.
Scale
The hard and adherent precipitate on the inner walls of the boiler is called scale.
Priming
Some droplets of liquid water are carried along with steam during the production of
steam in the boiler is called priming.
Foaming
The formation of stable bubbles above the surface of water is called foaming.
Caustic embrittlement
Formation of irregular, intergranular cracks at the welded joints, rivets etc. in high
pressure boilers is called caustic embrittlement.
Brackish water
The water containing high concentration of dissolved salts with salty or
brackish taste is called brackish water.
Reverse osmosis
The solvent flows from higher concentration to lower concentration.
CY6251 ENGINEERING CHEMISTRY - II
22
SCE Dept.of S & H
UNIT II
ELECTRO CHEMISTRY AND CORROSION
2.1 INTRODUCTION
Electrochemistry is the branch of science which deals with the relationship
between chemical reaction and electricity. Electrochemistry is the study of the process
involved in theinterconversion of electrical energy to chemical energy and vice – versa
Electric current is a flow of electrons generated by a cell or a battery when the
circuit is completed. A substance which allows electric current to pass through it ,is
called a conductor, e.g. metals, graphite, fused metallic salts while non – conductor is
a substance which does not conduct the electric current e.g. plastics, wood, non –
metals ect,
IMPORTANT TERMS INVOLVED IN ELECTROCHEMISTRY
Cell: Cell is an assembly of two electrodes and an electrolyte.Generally, it consists of
two half cells. Each half cell contain an electrode material in touch with electrolyte.
Current:Current is a flow of electricity through a conductor. It is measured in ampere.
Electrode is a material rod/bar/strip which conduct electrons.
Anode: Anode is an electrode at which oxidation occurs
Cathode: Cathode is an electrode at which reduction occur
Electrolyte: Electrolyte is a liquid or solution that conducts electric current. There are
three types of electrolytes.
(a) Strong electrolytes: these are the substances which ionize completely at any
concentration.
Example: HCL,aqueous solutions of NAOH, NaCl and KCL
(b)Weak electrolytes: Weak electrolytes are the substance which ionize partially in
solution.
Example: CH COOH, NH OH and aqueous solution of Na CO
(b) Non electrolyte: Non electrolyte are the substances which do not ionize at any
dilutions.
(c) Example: Glucose, Sugar,alcohol, petrol,etc.
Galvanic (or) Voltaic (or) Electrochemical cell
It is a device that produces electrical energy at the expense of chemical
energy produced in a reaction.
A cell consists of two half cells or electrodes.
A half-cell or electrode contains a metal rod dipped in an electrolytic
CY6251 ENGINEERING CHEMISTRY - II
23
SCE Dept.of S & H
solution. Electrolytic cell: It is a cell in which electrical energy brings
about a chemical reaction.
Electrochemical cell: It is a device that produces electrical energy at the
expense of chemical energy produced in a reaction.
Differences between electrolytic cell and electrochemical cell.
Electrolytic Cell Electrochemical cell
1. Electrical energy brings about a
chemical reaction.
2. Anode is positively charged.
3. Cathode is negatively changed.
4. Electrons move from anode to
cathode through external
circuit.
5. The extent of chemical reaction at
the electrode is governed by
Faraday‟s laws of electrolysis.
6. The amount of electricity passed
is measured by a coulometer.
7. One electrolyte and two electrodes
of the same element are generally
used in these cells.
1. Electrical energy is produced at the
expense of chemical
energy.
2. Anode is negatively charged.
3. Cathode is positively charged.
4. Electrons move from cathode
to anode through external
circuit.
5. The emf of the cell depends
on concentration of
electrolyte and nature of the
metal electrode.
6. The emf of the cell is measured
by a potentiometer.
7. Two different electrolytes and
two different electrodes are
often used.
2.1.1 TYPES OF CELL
Electrolytic cell It is a device in which chemical reaction proceed at the expanse of electrical energy.
Ex. Electro plating and electrolysis
Electrolysis of NaCl
The cell is constituted by dipping two platinum electrode in an appropriate
electrolyte ( NaCl in water ) . The electrodes are connected to the two terminals
of a battery. The electrode connected to positive terminal acts as anode (attracts
anions) and the other electrode connected to the negative terminal acts as
cathode (attracts cations). Chlorine is liberated at anode and hydrogen is
liberated at cathode
Cell reaction:
At anode: 2 Cl
▬▬► Cl2 ↑ + 2e
At cathode: (i) Na +
+ H2O ▬▬► NaOH + H+
CY6251 ENGINEERING CHEMISTRY - II
24
SCE Dept.of S & H
(ii) 2 H+
+ 2e
▬▬► H2↑
Net reaction: 2NaCl + 2H2O ▬▬► 2NaOH + H2 + Cl2
ECTROCHEMICAL CELL:
●consists of two half-cells joined by a salt bridge or some other path (porous
membrane)that allows ions to pass between the two sides in order to maintain electro
neutrality.
oxidation occurs at one half cell while reduction takes place at the other half cell.
cell with porous membrane
cell with salt bridge
CY6251 ENGINEERING CHEMISTRY - II
25
SCE Dept.of S & H
Note:Liquid junction potential is higher when porous membrane is used for
joining two half cells while it is minimum in a cell with a salt bridge.
Liquid junction potential occurs when two solutions of different
concentrations/compositions are in contact with each other through porous
membrane. It is due to formation of an electrical double layer of positive and
negative charges at the junction of the two solutions as the ions diffuse
through membranes.
Salt bridge: Contains a solution of a salt (KCl or KNO 3 or NH4NO3) that
literally serves as a bridge to complete the electric circuit, maintain electro
neutrality of electrolyte
and minimize the liquid junction potentia. For precise measurements of
potential, a salt bridge is used.
Fundamental components of electrochemical cell
1. Anode: oxidation half-reaction takes place ; ex. Zn Zn 2+ +2 e -
Oxidation of metal releases metal ions into the solution of oxidation half-
cell, leaving behind the electron at the surface of the metal electrode.
2. Cathode: reduction half-reaction occurs; ex. Cu2++ 2e - Cu
Movement of metal ions from the solution to the electrode to
gain es in reduction half cell leads to accumulation of positive
charge at the surface of the electrode.
3. Electrolyte:Internal conducting environment that allows ions to migrate
between both half cells so as to preserve electro neutrality
4. External circuit : Two half-cells are joined together by wire through which
electrons flow.
5. Salt bridge/porous membrane: Serves as a bridge to complete the
electric circuit and maintain electro neutrality in the electrolyte.
2.2 Electrochemical Cell or Galvanic cell
It is a device in which a redox reaction is used to derive electrical energy. During
the working of the cell the stored chemical energy decreases and this decrease is
gained as electrical energy.
In the electrochemical cell the electrode at which oxidation occurs is called anode
(− ve) and the electrode at which reduction occurs is called cathode (+ ve).
Example: Zn acts as anode and Cu acts as cathode in Daniel cell
CY6251 ENGINEERING CHEMISTRY - II
26
SCE Dept.of S & H
It consists of zinc electrode dipped in 1M zinc sulphate solution and a
copper electrode dipped in 1M copper sulphate solution. Each electrode acts as a half
cell connected by a salt bridge through a voltmeter. The two
solutions can seep through the salt bridge without mixing.
At anode: Oxidation takes place
Zn (s) ▬▬► Zn 2+
+ 2e _
At cathode: Reduction takes place.
Cu 2+
(aq) + 2e _
▬▬► Cu (s)
Net reaction: Zn (s) + Cu 2+
(aq) ▬▬► Zn 2+
(aq) + Cu (s)
Representation of a galvanic cell
(i) Galvanic cell consists of two electrodes, anode and cathode
(ii) The anode is written on the left hand side while the cathode is written on right side.
(iii) The anode is written with the metal first and then the electrolyte .The two are
separated by a vertical line or semicolon
Ex: Zn / Zn 2+
(or) Zn / ZnSO4 (or) Zn; Zn 2+
(iv) The cathode is written with electrolyte first and then the metal both are separated
by vertical line or semicolon
CY6251 ENGINEERING CHEMISTRY - II
27
SCE Dept.of S & H
Ex: Cu2+
/ Cu (or) CuSO4 / Cu (or) Cu ; Cu2+
(v) The two half cells are connected by a salt bridge which is indicated by two
parallel lines.
▬ +
Zn / ZnSO4 (1M ) ║ CuSO4 ( 1M ) / Cu
Salt bridge: It consists of a U tube filled with a saturated solution of KCl or
(NH4)2NO3 in agar-agar gel. It connects the two half cells and performs the following
functions
• It eliminates the liquid junction potential.
• It provides path for the flow of electrons between two half cells.
• Completes the circuit.
• Maintains electrical neutrality in the two compartments by migration of ions
through the porous material thus ensures the chemical reactions proceed
without hindrance
• Prevents mixing of the electrode solutions
2.2.1 Reversible cells
A cell works reversibly in the thermodynamic conditions. Ex. Daniel
cell, Secondary batteries, Rechargeable batteries.
The cell is reversible if it satisfies all the following conditions:
(i) If applied emf is equal to derived emf then the net reaction is zero
(ii) If applied emf is infinitesimally smaller than the derived emf then the cell should
act as electrochemical cell (forward reaction)
(iii) If applied emf is infinitesimally greater than the derived emf then the cell should
act as electrolytic cell (reverse reaction)
Irreversible cells
Cells which do not obey the (above) conditions of thermodynamic reversibility are
called irreversible cells. If one of the products escapes from the cell then that cell cannot
be made reversible by applying an external current.
Ex. Zinc-Silver cell, Primary cells
Zn –Ag Cell
Zn / H2SO4 (aq) / Ag
CY6251 ENGINEERING CHEMISTRY - II
28
SCE Dept.of S & H
Cell reaction:
Anode: Zn + H2SO4 ▬▬► ZnSO4 + H2 ↑
Cathode: 2Ag +
+ 2e_
▬▬► 2Ag
When two electrodes are connected from outside, zinc dissolves liberating hydrogen
gas. Since one of the product hydrogen escapes, the cell reaction cannot be reversed
when connected to an external EMF. The cell does not obey the conditions of
reversibility and is called irreversible cell.
2.3 Electrode Potential :
2.3.1 Oxidation potential
When a metal M is dipped in its salt solution, one of the following
reactions occurs depending on the metal :
1. Positive metal ions pass into the
solution : M →Mn+ + ne-
(oxidation)
(e.g.) When Zn rod is dipped in ZnSO4 solution, Zn goes into solution as
Zn2+.
The electrons attach to Zn rod, giving it a negative charge. The negative charge
on the rod attracts positive ions from solution. Thus a double layer of ions is
formed close to the rod.
CY6251 ENGINEERING CHEMISTRY - II
29
SCE Dept.of S & H
2.3.2 REDUCTION POTENTIAL
2. Positive ions from the solution deposit over the
metal.
Mn+ + ne- → M (reduction)
When Cu rod is dipped in CuSO4 solution, Cu+2 ions from the
solution deposit on metal rod. They attract negative ions from solution. Thus a
double layer of ions is formed close to the metal rod. This is called Helmholtz
double layer.
As a result a potential difference is set up between the metal and the
solution. The equilibrium value of the potential difference is known as electrode
potential.
Factors affecting electrode potential or emf of Cell :
(i) nature of the metal
(ii) temperature
(iii) concentration of metal ions in the solution
2.3.3 Single electrode potential (or) electrode potential :
It is a measure of the tendency of the metal electrode to lose or gain
electrons, when it is in contact with its own salt solution. It is developed due to
the formation of a double layer around the metal rod.
2.3.4 Standard electrode potential :
CY6251 ENGINEERING CHEMISTRY - II
30
SCE Dept.of S & H
It is a measure of the tendency of the metal electrode to lose or gain
electrons, when it is in contact with its own salt solution of 1M strength at 25C.
Measurement of single electrode potential : It is impossible to determine the value of a single electrode potential.
But we can always measure the potential difference between two electrodes
using a potentiometer, by combining the two electrodes to form a cell. For
this purpose we reference electrode. Standard hydrogen electrode is called
primary reference electrode. Calomel electrode is called secondary reference
electrode.
Standard hydrogen electrode (SHE) (Primary Reference Electrode)
It has a platinum foil connected to platinum wire and sealed in a glass
tube. The platinum foil is dipped in 1M HCl. Hydrogen gas 1 atm
pressure is passed through the side arm of glass tube as shown in the
figure. The standard electrode potential of SHE is taken as zero. The electrode
is represented,
Pt | H2(g) (1 atm) | H+ (1M)
The electrode reaction
is
2H+ + 2e- H2
CY6251 ENGINEERING CHEMISTRY - II
31
SCE Dept.of S & H
Limitations (or) drawbacks of SHE:
1) H2 gas reduces many ions like Ag+ and affects compounds of Hg, Ag etc.
2) It is difficult to get pure H2.
3) The pressure of H2 is to be kept 1 atm all the time.
4) It is difficult to set up and transport.
5) The electrode potential changes with barometric pressure.
6) A large volume of test solution is required.
7) It cannot be used in solutions of redox systems.
8) The solution may poison platinum surface. So we use a secondary reference
electrode.
Calomel Electrode (Secondary reference electrode):
It consists of a glass tube containing pure mercury at the bottom. A paste
of mercurous chloride covers the mercury. A solution of potassium chloride
is present over the paste. The bottom of the tube is sealed with a platinum
wire. There is a side tube for electrical contact. The electrode is represented as,
Hg | Hg2Cl2(s) | KCl(aq)
The electrode reaction is,
Hg2Cl2 + 2e- 2Hg + 2Cl-
The electrode potential is,
E = E° RT
ln [Cl-
]2
2F
E = E° RT
ln [Cl-
]
F
At 25oC,
E = E – 0.0591 log (Cl-)
For saturated KCl, E = +0.242 volt.
CY6251 ENGINEERING CHEMISTRY - II
32
SCE Dept.of S & H
Measurement of single electrode potential using a reference electrode
(saturated calomel electrode): The given electrode, say zinc electrode, is coupled with saturated
calomel electrode as in the figure. Since the reduction potential of zinc
electrode less than that of calomel electrode, zinc acts as anode and calomel as
cathode. The cell reaction will be
Zn/ ZnSO4 (1 M) // KCl (satd )/ Hg2Cl2/Hg
Zn + Hg2Cl2 Zn2+ + 2Hg + 2Cl-
The emf of the cell is measured using a potentiometer. The value of Ecell
=
1.002 volt.
Now, Ecell = EOright – E0
left
= EOcal – E
OZn
1.002 = 0.242 – E0Zn
EZn = 0.242-1.002
EZn = - 0.76 volt.
Advantages of Reference Electrode (Calomel Electrode):
CY6251 ENGINEERING CHEMISTRY - II
33
SCE Dept.of S & H
1. Easy to set up.
2. Easily transportable
3. Long shelf life
4. Reproducibility of emf
5. Low temperature coefficient
6. Electrode can be used in a variety of solutions.
7. Eo value is accurately known.
Ion sensitive electrode :
Ion sensitive electrodes have the ability to respond only to a specific ion
and develop a potential ignoring other ions in the solution.
The types (classification) of ion-sensitive electrode :
1) Glass membrane electrodes
2) Solid state electrode
3) Pungor or precipitate electrodes
4) Liquid – liquid electrode
Glass Electrode (or) Measurement of pH using glass electrode :
Glass electrode contains a thin-walled glass bulb. The glass has low
melting point and high electrical conductivity. 0.1M HCl is present in the
bulb. A platinum wire is inserted in the acid.
When the glass membrane separates two solutions differing in pH,
exchange of H+ ions takes place between the solutions. As a result a
potential is developed across the membrane. The potential EG is given by,
EG = EG + 0.0591
pH
CY6251 ENGINEERING CHEMISTRY - II
34
SCE Dept.of S & H
Measurement of pH :
The glass electrode is dipped in the given solution. This system is
connected to saturated calomel electrode as in the figure. The emf of the
resulting cell is measured using a potentiometer.
From the emf, the pH of the solution is calculated as
below: Ecell = Eright – Eleft
Ecell= Ecal – Eglass
Ecell = 0.242 – (EG + 0.0591v pH)
Ecell = 0.242 - EG - 0.0591 pH
PH =Ecell – 0.2422+E
0Glass/0.0592
Advantages of Glass Electrode : i)It is easily constructed and used
ii)Results are accurate
iii)Electrode is not easilpoisoned
iv) Equilibrium is quickly attained
v) It can be used in strong oxidizing solutions, coloured solutions and
in presence of metal ions
vi) Using special glass electrode, pH can be measured from 0 to 12.
CY6251 ENGINEERING CHEMISTRY - II
35
SCE Dept.of S & H
vii) It is used in chemical, industrial, biological and agricultural laboratories.
Disadvantages or Limitations : i) Glass has high resistance. So special electronic potentiometer
must be used.
ii) It cannot be used in highly alkaline solutions, in pure ethanol or in
acetic acid. If the solution pH is more than 12, glass membrane is
affected by cations.
Applications of Ion-sensitive electrode :
i) To determine ions like H+, K+, Li+, etc.
ii) To determine hardness of water (Ca+2 and Mg+2 ions)
iii) To determine concentration of F-, NO3-, CN- etc.
iv) To determine concentration of a gas using gas-sensing
electrodes.
v) To determine pH of a solution using H+ ion sensitive electrode.
2.4 EMF of an electrochemical cell
● Difference of potential which causes the flow of current from the electrode
of higher potential to one of lower potential
● It is the algebraic sum of the single electrode potentials provided the proper sign
are given according to actual reaction taking place on the
Nernst eqn for electrochemical cell
ECell=E right-Eleft, or Ecell =E cathode -Eanode
E° cell+
0.0592Vlog[reactant]/[p
roduc)
2.4.1Instrument:
● emf of the cell can be measured by potentiometer-using
Poggendorff’s compensation principle(wheatstone's bridge).
● Voltmeter cannot be used to determine accurate value of emf because during
measurement a part of cell current is drawn which causes change in the emf.
Factors affecting the emf of a cell
1.Nature of the electrolytes and electrodes.
2.Concentration and composition of the electrolytes.
3.pH and temperature of the solution.
2.4.2 Applications of EMF Measurements
The valency of an ion can be determined.
Solubility of a sparingly soluble salt can be determined.
Potentiometric titrations can be carried out.
Hydrolysis constant can be determined.
CY6251 ENGINEERING CHEMISTRY - II
36
SCE Dept.of S & H
Determination of standard free energy change and equilibrium constant
Determination of pH by using a standard hydrogen electrode.
2.5 ELECTROCHEMICAL SERIES (e.m.f series)
A series in which elements are arranged in the ascending (increasing ) order
Of their standard reduction potential is called emf series.
2.5.1Significance of EMF series
Half cell reaction Eo
(V)
Li+
+ e-
→ Li - 3.04
Mg2+
+ 2e- -
→ Mg - 2.37
Al3+
+ 3e- -
→Al - 1.66
Zn2+
+ 2e- -
→ Zn - 0.76
Fe2+
+ 2e- -
→ Fe - 0.44
2H+
+ 2e- -
→ H2 (g) 0.00
Hg 22+
+ 2e▬ → Hg (l) 0.2422
Cu2+
+ 2e- -
→ Cu 0.34
Cu+
+ e--
→ Cu 0.52
Pt,Fe3+
+ e▬ → Fe2+
0.77
Ag+
+ e--
→ Ag 0.80
Au+
+ e-
→ Ag 1.69
F2 + 2e- -
→ 2F-
2.8
Application / Significance of electrochemical series
(i) Relative ease of oxidation or reduction • The metals which lie above hydrogen in the series undergo spontaneous
oxidation and the metals which lie below SHE undergo reduction
spontaneously ( ie. Acts as Anodes and Cathodes respectively)
• The metals which lie above hydrogen are good reducing agents and which lies
below hydrogen will act as good oxidizing agents
(ii) Replacement tendency • The metal lying above in emf series displaces the metal lying below it from an
electrolyte of the later.
Example 1: Ni spatula cannot be used to stir copper sulphate solution due to
the following reaction
Ni(s) + Cu2+
(aq) ▬▬► Ni 2+
(aq) + Cu (s)
CY6251 ENGINEERING CHEMISTRY - II
37
SCE Dept.of S & H
Example 2: when zinc is dipped in copper sulphate solution copper gets deposited
(displaced)
Zn (s) + CuSO4 (aq) → Zn SO4 (aq) + Cu (s)
(iii) Liberation of Hydrogen • The metal with negative reduction potential will displace H2 from an acid
solution
Zn (s) + 2 HCl (aq) → Zn Cl2 (aq) + H2 ↑
Hence acids cannot be stored in galvanized steel containers.
For exactly the same reason galvanized steels are not used to store food stuffs
containing vinegar. (Vinegar is used as food preservative- vinegar is acetic acid)
(iv) Calculation of equilibrium constant (Keq)
∆GO
= n F Eo
−∆GO
= 2.303 RT log K(eq) Therefore
log K(eq) = n F Eo
2 .303 RT
log K(eq) = nEo
0.0591
(v) Calculation of Standard emf of the cell E cell = E cathode − E anode
( if both reduction potentials are considered)
E cell = E cathode + E anode
( if oxidation potential of anode and the reduction potential of cathode
are considered)
(vi) Corrosion • The metals higher in the series are anodic and are more prone to corrosion.
• The metals lower in the series are noble metals (cathodic) and they are less prone
to corrosion.
(vii) Predicting the spontaneity of cell reaction • Spontaneity of the redox reaction can be predicted from the emf value of
complete cell reaction.
If the value of Ecell is positive, the reaction is feasible. as ∆G will be negative
( i.e. it is an electrochemical cell)
If the value of Ecell is negative, the reaction is not feasible. as ∆G will be positive
( i.e. it is an electrolytic cell)
CY6251 ENGINEERING CHEMISTRY - II
38
SCE Dept.of S & H
2.6 NERNST EQUATION
If an emf of a reversibile cell is E volts and the cell reaction that takes place is
accocated with the passage of an faradays or nF coulombs, the electrical work done by the
system is given by the product of the emf and total charge.
Electrical work done by the system = nFE, where E is the reversibile emf of the
cell and n is the no.of electrons involved in the cell reaction.
he work done on the system at constant temperature is the increase in the free
energy ΔG of the system
The free energy change of a reaction depends on the activities of the reactants and
the products. Therfore, in the case of cell reactions of a reversibile, the emf of the cell will
also depend on the activities of the reactant and products.
Applications of Nernst Equation :
I)To calculate electrode potential of unknown metal.
ii)To predict corrosion of metals.
iii) To set up electrochemical series.
CY6251 ENGINEERING CHEMISTRY - II
39
SCE Dept.of S & H
2.6.1Nernst equation for a reversible cell :
Let us consider the reaction in a reversible cell :
A + B C + D ----- (1)
The free energy change G of this equilibrium is related to the
equilibrium
constant K by the Van‟t Hoff isotherm.
ΔG = ΔG° + RTln
[Product]
[Reactant]
-----(2)
We know, G = - nFE
G = -nFE ------ (3)
Substituting equations (1) & (3) in equation (2)
-nFE = -nFE° RTln [C][D]
[A][B]
-----(4)
CY6251 ENGINEERING CHEMISTRY - II
SCE Dept.of S & H
E = E° 0.0591
log [C][D]
n [A][B]
This is Nernst equation for a reversible cell.
2.6.2 PROBLEM BASED ON NERNST EQUATION
Calculate the reduction potential of lead electrode in contact with a solution of 0.015M Pb2+
ions.( E0
= -0.13 volt)
GIVEN
Std Oxidation potential is given as
Pb2+
+ 2 e- → Pb; E
0 = -0.13v
Concentration of Pb2+
= 0.015M
Solution
The Nernst equation for reduction potential is
E = E0
red + 0.0591/n log(Pb
2+)
E = -0.13 +.o2955(-1.824)
E = -0.1839V
Oxidation potential of Pb = -0.1839V
2.7 Corrosion
It is the gradual deterioration of metals by chemical, electrochemical or
biochemical interaction with the environment.
Causes of Corrosion
Metals occur in nature as their oxides, sulphides carbonates etc. The
chemically combined state is thermodynamically more stable. When we extract a
metal from its ore, the metal is in a higher energy state, which is thermodynamically
unstable. So it tries to go back to the stable state by chemical or electrochemical
interaction with the environment.
2.7.1 Consequences or effects of Corrosion
1. Efficiency of the machine decreases.
2. Plant has to be shut down due to failure.
3. Product is contaminated.
4. The toxic products of corrosion cause health hazards.
5. There is a necessity to over design to allow for corrosion.
2 . 8 T y p es or Theories of Corrosion
I. Dry or Chemical Corrosion
II. Wet or Electrochemical Corrosion
40
CY6251 ENGINEERING CHEMISTRY - II
SCE Dept.of S & H
2.8.I. Dry or Chemical Corrosion
It is due to the attack on metal surface by atmospheric gases like O2, SO2, H2S etc.
(e.g.) Tarnishing of silver by H2S.
There are three types of dry or chemical corrosion.
1) Oxidation Corrosion
2) Corrosion by Hydrogen
3) Liquid Metal Corrosion
(1) Oxidation Corrosion
It is due to the direct attack of oxygen on metal surface in the absence of
moisture. Alkali and Alkaline earth metals are corroded at low temperatures. At high
temperatures, most metals except Au, Pt and Ag are oxidized.
Mechanism
i) Oxidation occurs at the surface of the metal to form M2+ ions.
M M2+ + 2e-
ii) Oxygen takes up the electrons. O2 is reduced to O2-
½ O2 + 2e- O2-
iii) O2- ion reacts with M2+ to form metal oxide.
M2+ + O2- MO
The metal surface is converted to a monolayer of metal oxide. Further
corrosion occurs by diffusion of M2+ ion through the metal oxide barrier. The growth
of oxide film is perpendicular to the metal surface.
Different types of oxide films are formed.
(i) Porous and Non-Porous Oxide Film (or) Pilling-Bedworth Rule
(a) If the volume of the oxide layer formed is less than the volume of the metal
41
CY6251 ENGINEERING CHEMISTRY - II
SCE Dept.of S & H
consumed, the oxide layer is porous. (e.g.) The volumes of oxides of alkali and alkaline earth
metals are less than the volume of the metal consumed. So the oxide layer is porous and non-
protective
(b) If the volume of the oxide layer formed is greater than the volume of the metal consumed, the
oxide layer is non-porous.(e.g.) The volumes of oxides of heavy metals such as Pb, Sn are greater
than the volumes of the metal consumed. So the oxide layer is non-porous and protective.
(ii) Stable Oxide Layer
A stable oxide layer is firmly adsorbed on the metal surface. The layer is
impervious and prevents further corrosion. So the layer itself acts as a protective
coating. (E.g.) Oxides of Al, Cu etc.
(iii) Unstable oxide Layer
This is mainly produced on the surface of noble metals such Ag, Au etc. The unstable oxide
decomposes to stable metal and oxygen. Metal Oxide Metal + Oxygen
(iv) Volatile Oxide
The oxide film volatilizes as soon as it is formed. It leaves fresh metal surface for further
continuous attack. (e.g.) Molybdenum oxide MoO3.
(2) Corrosion by Hydrogen
(a) Hydrogen embrittlement
Definition
It is formation of cracks and blisters on the metal by hydrogen gas when the metal comes into
contact with H2S. Iron liberates atomic hydrogen by reacting with H2S.
Fe + H2S FeS + 2H
Hydrogen atoms diffuse into the voids of metal matrix. When the pressure of the gas increases,
cracks and blisters develop on the metal.
(b) Decarburisation
It is the process of decrease in the carbon content of steel. At high temperature, molecular
hydrogen decomposes to atomic hydrogen. High Temperature
H2 2H
When steel is exposed to this environment, carbon in the steel reacts with atomic hydrogen.
C + 4H CH4
Hence the carbon content in steel decreases. Collection of methane gas in the voids of steel
develops high pressure and causes cracking.
(3) Liquid Metal Corrosion
It is due to the chemical action of flowing liquid metal at high temperature. It involves :
(i) dissolution of a solid metal by the liquid metal.
(ii) Penetration of liquid metal into the solid metal.
2.8.2. Wet (or) Electrochemical Corrosion :
It occurs under the following conditions.
(i) When two dissimilar metals or alloys are in contact with each other in presence of an aqueous
solution or moisture.
(ii) When the metal is exposed to an electrolyte with varying amounts of oxygen.
Mechanism of Wet Corrosion
(1) Metal dissolution occurs at the anode.
M →Mn++ + ne-
(2) Reduction reaction occurs at the cathode in different environments.
(a) Acidic environment : Here hydrogen gas is evolved at the cathode.
2 H+ + 2e- →H2
42
CY6251 ENGINEERING CHEMISTRY - II
SCE Dept.of S & H
(b) Neutral environment : In neutral or slightly alkaline medium, hydroxide ions are formed at the
cathode.
½ O2 + 2e- + H2O →2OH-
(a) Hydrogen Evolution type corrosion (In Acidic Medium)
All metals above hydrogen in the electrochemical series tend to get dissolved
in acidic solution with simultaneous evolution of H2 gas. e.g.) When iron comes into contact with
non-oxidising acid like HCl, hydrogen evolution occurs.
At anode : Iron is oxidized to Fe2+
Fe →Fe+2 + 2e-
At cathode : H+ ion is reduced to H2.
2 H+ + 2e- →H2
oxygen, OH- ions are formed.
At anode : Iron is oxidized to Fe
(b) Absorption of Oxygen (or) Formation of hydroxide ion type corrosion (In
neutral or weakly alkaline medium)
The surface of iron is normally coated with a thin film of iron oxide. But if some cracks develop
on the film, anodic areas are created on the surface. The rest of the metal part acts as cathode.(e.g.)
When iron is in contact with an electrolyte solution in presence ofoxygen, OH- ions are formed.
At anode : Iron is oxidized to Fe+2
At cathode : Production of OH- ions (more aeration)
½ O2 + 2e- + H2O →2OH
Waterline corrosion
Let us consider metal tank partially filled up with water. The metal area above water line is
exposed to higher concentration of oxygen (cathode) than the metal below water level. The metal
less exposed to O2 acts as anode and corrodes. This is called water line corrosion.
Examples of differential aeration corrosion
i) Pitting or localized corrosion
ii) Crevice corrosion
iii) Pipeline corrosion
43
CY6251 ENGINEERING CHEMISTRY - II
SCE Dept.of S & H
iv) Corrosion on wire fence
(i) Pitting Corrosion
It is the localized attack resulting in the formation of a hole due to corrosion.
Example : Metal area covered by a drop of water, sand, dirt etc.
The area covered by the drop or dirt acts as anode and corrodes. Theuncovered area exposed to air
or O2 acts as cathode.The rate of corrosion is more if the cathodic area is larger and anodic area is
smaller. Thus more material is removed from the same area and a pit is formed.
At anode : Iron is oxidized to Fe+2
Fe →Fe2+ + 2e-
At cathode : O2 is reduced to OH-.
½ O2 + H2O + 2e- →2OH
Overallreaction :
Fe2+ + OH- →Fe(OH)2
At anode : Iron is oxidized to Fe+2
Fe →Fe2+ + 2e-
At cathode : O2 is reduced to OH-.
½ O2 + 2e- + H2O →2OH
OverallReaction
Fe+2 + 2OH- →Fe(OH)2
If enough oxygen is present, Fe(OH)2 is oxidized to Fe(OH)3.
4Fe(OH)2 + O2 + H2O →4Fe(OH)3
Differences between chemical corrosion and electrochemical corrosion:
Chemical Corrosion Electrochemical Corrosion
1. It occurs in dry condition It occurs in presence of moisture or electrolyte.
2. It occurs by the direct chemical attack on the metal by the environment.It occurs by the
formation of a large number of anodic and cathodic areas.
3. Even a homogenous metal surface iscorroded.Only heterogeneous or bimetallicsurface is
corroded.
4. Corrosion products gather at the placeof corrosion.Corrosion occurs at the anode, whilethe
products form elsewhere.
5. It is a self controlled process It is a continuous process
6. It takes place by adsorption mechanism. It follows electrochemical reaction.(e.g.) Mild scale
formation on iron surface (e.g.) Rusting of iron under moist atmosphere
Types of electrochemical corrosion
There are two types:
(i) Galvanic corrosion
(ii) Differential aeration or Concentration cell corrosion
44
CY6251 ENGINEERING CHEMISTRY - II
SCE Dept.of S & H
(i) Galvanic corrosion
When two different metals are in contact with each other in presence of aqueous solution or
moisture, galvanic corrosion takes place.
The metal with more negative electrode potential acts as anode. Metal with less negative electrode
potential acts as cathode. In the Zn-Fe couple as shown in the figure, zinc with more negative
electrode potential, dissolves in preference to iron. Zn acts as anode and Fe as cathode.
Example :
Steel screw in a brass marine hardware easily undergoes corrosion. Iron has E0 = -0.44V. For Cu
E0 = +0.34 V. Iron corrodes in preference to Cu.
Prevention
Galvanic corrosion is minimized by providing an insulation between the two metals.
(ii) Differential aeration (or) concentration cell corrosion
Let a metal be partially immersed in a conducting solution. The part of the
metal above the solution is more aerated and acts like cathode. The less aerated metal part inside
the solution acts as anode and corrodes.
At anode : Corrosion occurs (less aeration)
M →M2+ + 2e
At cathode : Production of OH- ions (more aeration)
½ O2 + 2e- + H2O →2OH
Wateline corrosion
Let us consider metal tank partially filled up with water. The metal area above water line is
exposed to higher concentration of oxygen (cathode) than the metal below water level. The metal
less exposed to O2 acts as anode and corrodes. This is called water line corrosion.
Examples of differential aeration corrosion
i) Pitting or localized corrosion
ii) Crevice corrosion
iii) Pipeline corrosion
iv) Corrosion on wire fence
45
CY6251 ENGINEERING CHEMISTRY - II
SCE Dept.of S & H
(i) Pitting Corrosion
It is the localized attack resulting in the formation of a hole due to corrosion.
Example : Metal area covered by a drop of water, sand, dirt etc.
The area covered by the drop or dirt acts as anode and corrodes. The uncovered area exposed to air
or O2 acts as cathode. The rate of corrosion is more if the cathodic area is larger and anodic area is
smaller. Thus more material is removed from the same area and a pit is formed.
At anode : Iron is oxidized to Fe+2
Fe →Fe2+ + 2e-
At cathode : O2 is reduced to OH-.
½ O2 + H2O + 2e- →2OH
Overall reaction :
Fe2+ + OH-→Fe(OH)2
(ii) Crevice Corrosion
Let a crevice or crack between two different metallic objects be in contact
with a liquid. The crevice acts like anode due to less oxygen availability and corrodes.
The exposed area acts as cathode.
(e.g.) rivets, joints.
(iii) Pipeline Corrosion
Buried pipelines or cables passing from one type of soil (clay, less aerated) to another type (sand,
more aerated) get corroded due to differential aeration.
(iv) Corrosion on wire fence
46
CY6251 ENGINEERING CHEMISTRY - II
SCE Dept.of S & H
In a wire fence, the wires at the crossings are less aerated than the rest of the
fence. So corrosion takes place at the wire crossings, which become anodic.
2.9 Factors influencing corrosion
2.9.1. Nature of the metal
(i) Position in emf series
Metals above hydrogen in the electrochemical series corrode easily because they have negative
reduction potential. When two metals are in contact, the more active metal with a higher negative
potential corrodes.
(ii) Areas of anode and cathode
Corrosion will be severe if the anodic area is smaller and cathodic area is larger. The larger
cathodic area demands more electrons. So the anodic area corrodes faster.
(iii) Purity
100% pure metal will not corrode. (e.g.) Pure Zn does not corrode. If the metal has trace amount of
impurity, it corrodes. (e.g.) Zinc metal with iron or copper impurity forms an electrochemical cell.
The base metal Zn acts as anode and corrodes.
(iv) Over Voltage
Corrosion rate is inversely proportional to the over voltage of the metal in a corrosive
surroundings. (e.g.) The hydrogen over voltage of Zn in 1M H2SO4 is 0.7V. So the rate of
corrosion is low. But when some Cu impurity is present, the over voltage is reduced and corrosion
rate increases.
(v) Nature of the Film
Nature of film formed on the metal surface determines extent of corrosion.(e.g.) In the case of
alkali and alkaline earth metals, the oxide film formed is porous .The corrosion continues. In the
case of heavy metals, the oxide film is non-porous. The film acts as a protective layer.
(vi) Nature of corrosion product
If the corrosion product is soluble in the corroding medium, corrosion rate is faster. Similarly if the
corrosion product is volatile (e.g. MoO3), corrosion will be more.
2.9.2. Nature of Environment
(i) Temperature
Increase of temperature increases corrosion rate because the rate of diffusion of ions increases.
(ii) Humidity
Rate of corrosion is more, if humidity of environment is high. Moisture acts as
solvent for O2, CO2 etc, to produce electrolyte necessary for formation of corrosion
cell.
(iii) Corrosive gases
Acidic gases like CO2, SO2, H2S etc, produce electrolytes and increase corrosion.
(iv) Presence of suspended particles
Particles like NaCl, (NH4)2SO4 along with moisture are powerful electrolytes and increase rate of
corrosion.
(v) Effect of pH
Generally in alkaline medium, the rate of corrosion is less compared to acidic medium.
The effect of pH on the corrosion of iron in water is shown in the Pourbaix diagram as indicated in
the figure.
47
CY6251 ENGINEERING CHEMISTRY - II
SCE Dept.of S & H
The figure shows zones of corrosion, immunity and passivity. Z is the point at which pH=7 and
corresponding electrode potential is E= -0.2V. This is in the corrosion zone. So iron rusts under
these conditions.
The rate of corrosion can be altered by shifting the point Z to different regions.
1) If the potential is changed to -0.8V by applying external current, iron becomes immune to
corrosion.
2) If the potential applied is positive, iron becomes passive.
3) If the pH is increased to more than 7, corrosion rate decreases.
4) If the pH is reduced to less than 7, rate of corrosion increases
2.10 CORROSION CONTROL
The rate of corrosion can be controlled by modifying the metal or environment. Some control
methods are
1) proper selection of metals
2) Use of pure metals
3) Use of metal alloys
4) Cathodic protection
a. Sacrificial anode protection
b. Impressed current cathodic protection
5) Changing the environment
6) Use of inhibitors
a. Anodic inhibitors
b. Cathodic inhibitors
7) Applying protective coatings
1) Proper selection of metals
Noble metals are used in ornaments and in surgical instruments, because they do not corrode.
Contact of dissimilar metals far away from each other in electrochemical series should be avoided.
2) By using pure metals
Pure metals have high corrosion resistance. Even a trace of impurity will lead to corrosion, the
base metal becoming anode.
3) Use of alloys
Use of metal alloys is a good method of protection against corrosion. (e.g.) Stainless steel
containing chromium forms a coherent oxide film which protects steel against further attack
2.10.1 Proper designing i. Complicated designs with more angles, sharp edges and corners should be avoided.
ii. Direct contact of dissimilar metals lead to galvanic corrosion. So insulating material between
the two metals should be inserted.
48
CY6251 ENGINEERING CHEMISTRY - II
SCE Dept.of S & H
iii. Smaller area for cathode and larger area for anode must be provided.
iv. Tanks and containers should be designed such that the liquid should be drained off completely.
v. Crevices should be avoided or they should be filled using fillers.
vi. Bendings should be smooth.
vii. Annealing minimizes corrosion.
5) Cathodic Protection
The metal to be protected is made to act like a cathode. This is achieved in two ways.
a) Sacrificial anodic protection
Here the metal to be protected is made cathode by connecting it to a more active metal (anodic
metal) called sacrificial anode. Only the more active metal will
a) Sacrificial anodic protection
Here the metal to be protected is made cathode by connecting it to a more active metal (anodic
metal) called sacrificial anode. Only the more active metal will be corroded, protecting the parent
metal. Since the anodic metal is sacrificed, the method is called sacrificial anodic protection. Mg,
Zn are used as sacrificial anodes.Metal to be protected
49
CY6251 ENGINEERING CHEMISTRY - II
SCE Dept.of S & H
Applications
i) Protection of buried pipelines, cables
ii) Protection of ships and boats
iii) Calcium metal is used to minimize engine corrosion
iv) Magnesium sheets are inserted into domestic water boilers to prevent rust
formation.
b) Impressed current cathodic protection method
Here an impressed current is applied in an opposite direction to annul the corrosion current. Thus
the corroding metal is converted to cathode from anode.The negative terminal of battery is
connected to the metal to be protected. The positive terminal is connected to an inert electrode like
graphite. The anode is buried in a „back-fill‟ (containing a mixture of gypsum, coke breeze and
sodium sulphate) to increase electrical contact.
Mg Metal to be protected
APPLICATION
i) Protection of tanks, transmission line towers, underground water pipes, oil pipe line, ships etc.
Limitations
i) It is costly
ii) It fails when current is switched off.
Corrosion inhibitors
A corrosion inhibitor is a substance that reduces corrosion, when added to the corrosive
environment. There are three types of inhibitors.
i) Anodic inhibitors - chromate, nitrate
ii) Cathodic inhibitors - amines
iii) Vapour phase inhibitors - benzonitrile.
i) Anodic inhibitors
(e.g.) chromate, nitrate, phosphates, tungstate.
50
CY6251 ENGINEERING CHEMISTRY - II
SCE Dept.of S & H
The inhibitors form insoluble compound with the newly produced metal ions and prevent
corrosion. This compound is adsorbed on the metal surface to form a passive film. Anodic
inhibitors are used to repair
i) the crack of oxide film on metal surface
ii) pitting corrosion
iii) porous oxide film on metal surface
ii) Cathodic inhibitors
There are two types depending on the nature of cathodic reaction in an electrochemical reaction.
a) In acidic solution
Example : amines, thiourea, mercaptans act as inhibitors.Here evolution of H2 is the cathodic
reaction.
2 H+ + 2e- →H2
The corrosion is controlled by slowing down the diffusion of H+ ions to cathode by addition of the
inhibitor which is adsorbed on the metal surface.
b) In neutral solution
Example : hydrazine, sodium sulphite act as inhibitors.Here OH- ions are formed at cathode.
H2O + ½ O2 + 2e- →2 OH
Corrosion is controlled by eliminating O2 from the corroding medium by
adding Na2SO3. The OH- ions can be eliminated by salts of Mg, Zn etc.
iii) Vapour phase inhibitors
(e.g.) benzotriazole, dicyclohexyl ammonium chromate act as inhibitors.These organic inhibitors
readily vapourise and form a protective layer on the metal surface.
2.10.2 Control of corrosion by modifying the environment:
There are five methods
1. Deaeration :
Presence of oxygen increases corrosion rate. Deaeration involves removal of dissolved oxygen by
increasing the temperature together with the mechanicalagitation. This also removes dissolved
oxygen.
2. Deactivation:
It is the removal of dissolved oxygen by adding chemicals in aqueous solution.
(E.g.) 2Na2SO3 + O2 →2Na2SO4
3. Dehumidification:
It is the removal of moisture from the air by reducing the relative humidity of the surrounding air.
It can be achieved by adding silica gel or alumina which absorbs
moisture.
4. Alkaline neutralization:
The acidic nature of the corrosive environment is due to the presence of HCl,
SO2, CO2 etc. They are neutralized with alkali spray. E.g. NaOH lime etc.
5. Using corrosion inhibitors :
A corrosion inhibitor is a substance that reduces the corrosion of a metal when added to corrosive
environment
Applications
To prevent corrosion in closed space, storage containers, sophisticated equipment etc.
PROTECTIVE COATINGS
Metal surface is covered by a protective coating to prevent corrosion. The coating acts as a
physical barrier between the metal surface and the environment. The coating gives a decorative
appeal and also imparts hardness, oxidation resistance and thermal insulation to the surface. The
main types of coating are:
51
CY6251 ENGINEERING CHEMISTRY - II
SCE Dept.of S & H
1) Metallic coating
2) Chemical conversion coating
3) Organic coating
4) Non-metallic coating
2.11 PAINT
Paint is a mechanical dispersion of one or more fine pigments in a medium (thinner + vehicle).
When a paint is applied to metal surface, the thinner evaporates. The vehicle undergoes slow
oxidation to form a pigmented film.
2.11.1 Requirements or requisites of a good paint
A good paint should,
i) have good covering power
ii) spread easily on the surface
iii) not crack on drying
iv) adhere well to the surface
v) give a glossy film
vi) be corrosion and water resistant
vii) have stable colour
2.11.2Constituents of Paint
Pigment
Vehicle
Thinner
Drier
Filler
Plasticizer
Anti skinning agent
1. Pigment
It is a solid that gives colour to the paint.
Functions:
1.To give colour and opacity to the film.
2.To provide strength to the film.
3.To protect film by reflecting U.V. rays.
4.To provide resistance to abrasion and weather.
Example:
White pigment - White lead, TiO2
Blue pigment - Prussion blue
Green pigment - Chromium oxide
Red pigment - Red lead, Fe3O4
2. Vehicle (or) Drying Oil
It is the film-forming liquid. It holds the ingredients of the paint. It is a nonvolatile high molecular
weight fatty acid of vegetable or animal.
Function
1.To hold the pigment on the surface.
2.To form a protective layer by oxidation and polymerization.
3.To impart water repellency, toughness and durability of film.
4.To improve adhesion of film.
Example
Lin seed oil, Castor oil.
3. Thinner
It is the volatile portion of paint. It is added to reduce the viscosity of the paintfor easy application
on the surface. It easily evaporates after paint is applied.
52
CY6251 ENGINEERING CHEMISTRY - II
SCE Dept.of S & H
Functions
1.To reduce viscosity of paint.
2.To dissolve vehicle and other additives.
3.To suspend the pigments.
4.To increase elasticity of film.
5.To increase penetration of vehicle.
6.To improve drying of film.
Example
Turpentine, Dipentine, Xylol.
4. Drier
It is a substance used to speed up drying of the paint.
Functions
1.To act as oxygen carrier or catalyst.
2.To provide oxygen essential for oxidation and polymerization of drying oil.
Example
Metallic soap, linoleate and resinate of Co, Mn etc.
5. Extender or Filler
These are white pigments that form bulk of the paint.
Functions
1.To reduce cost of paint
2.To prevent shrinkage and cracking of film
3.To modify shades of pigment
4.To retard settling of pigments in paint.
Example
Talc gypsum, china-day.
6. Plasticizer
It is added to the paint to provide elasticity to the film and prevent its cracking.
Example
Triphenyl phosphate, Tricresyl phosphate
7. Antiskinning agent
It is a chemical added to the paint to prevent gelling and peeling of the paint.
Example
Polyhydroxy phenols.
Pigment Volume Concentration (P.V.C.)
The P.V.C. of a paint is calculated using the equation.
P.V.C. =
Volume of pigment in the paint =Volume of pigment in the paint + Volume of non-volatile vehicle
in the paint
If P.V.C. is high, durability, adhesion and consistency of the paint will be low.
Failure of Paints
A paint may fail due to any one of the following reasons:
i) Chalking : It is the gradual powdering of the paint film on the painted surface. This happens due
to improper dispersion of pigment in vehicle.
ii) Cracking : A paint film cracks due to unequal expansion or contraction of paint coats.
Evasion : This is very quick chalking.
iv) Blistering : It is due to improper surface exposure of paint to strong sunshine.
2.12 Metallic Coating
2.12.1 Electroplating or Electro-deposition
It is the deposition of coat metal on the base metal by passing direct current through an electrolytic
solution of a soluble salt of the coat metal. The base metal to be electroplated acts as cathode. The
coat metal or an inert electrode forms anode. The electrolyte is a soluble salt of coat metal.
53
CY6251 ENGINEERING CHEMISTRY - II
SCE Dept.of S & H
Objectives or uses or applications of Electroplating:
i) To enhance resistance to corrosion of base metals.
ii) To give a decorative appearance.
iii) To enhance resistance to chemical attack.
iv) To improve hardness and wearing resistance.
v) To obtain polished surface.
Theory If the coating metal itself forms the anode, the concentration of electrolyte bath does not change
during electrolysis. The metal ions deposited on the cathode are replenished continuously by
dissolution of the anode.
Example
Electroplating of Gold
The object to be gold plated is treated with organic solvent like acetone, CCl4
to remove grease, oil etc. It is then washed with dil H2SO4 to remove scales, oxides
etc. The cleaned object is made cathode of electrolytic cell. Anode is a gold plate.
AuCl3 solution is the electrolyte. When current is passed into the solution, gold ions
migrate to the cathode, get reduced and deposit on the object.
Ionisation : AuCl3→Au+3 + 3Cl-
At Cathode :
Au+3 + 3e- →Au
At anode :
Au →Au+3 + 3e-
Au+3 + 3Cl- →AuCl3
To achieve a strong adherent and smooth deposit, glue or gelatin is added to the electrolyte bath.
To enhance the brightness of the deposit, brightening agents are added to the bath.
Conditions
i) Temperature : 600C
ii) Current density : 1 to 10 mA/cm2
iii) Low metal ion concentration
iv) Buffer solution to maintain pH.
Applications or Uses or Objectives
i) To give a decorative appearance.
ii) Electrical and electronic applications
iii) To get a thin coating of gold on cheap jewellery
iv) To achieve oxidation resistance, corrosion resistance etc.
2.12.2 Electroless Plating
It is the deposition of a noble metal (from its salt solution) on a catalytically active metal surface
using a reducing agent without use of electric current.The reducing agent reduces the metal ions.
The metal atoms get deposited over the surface to give a thin uniform coating.
Metal ions + reducing agent metal (deposited) + oxidation product
54
CY6251 ENGINEERING CHEMISTRY - II
SCE Dept.of S & H
Example
Electroless nickel plating
The various steps are:
Step I : Pretreatment and activation of the surface:
The surface to be plated is degreased by using organic solvents or alkali and then accompanied by
acid treatment.
i) The surface of stainless steel is activated by dipping in hot solution of 50% H2SO4.
ii) Mg alloy surface is activated by giving a thin coating of zinc and copper overit.
iii) Al, Cu, Fe, brass etc, do not require activation.
iv) Plastic, glass etc, are activated by dipping in a solution of SnCl2/HCl and then
in PdCl2 solution. On drying a thin layer of palladium is formed on the surface.
Step II : Preparation of plating bath:
The plating bath consists of:
i) Coating Metal : A solution of NiCl2 20g/lit.
ii) Reducing agent : Sodium hypophosphite 20g/lit.
iii) Exaltant to accelerate coating rate and complexing agent : Sodium succinate
15g/lit.
iv) Buffer to maintain pH at 4.5 : Sodium acetate 10g/lit.
v) Temperature 93oC
The pretreated object is immersed in the plating bath for required time. The following reactions
occur and nickel is coated on the object.
Cathode : Ni2+ + 2e- →Ni
Anode : H2PO2- + H2O →H2PO3- + 2H+ + 2e
Overall Reaction : Ni2+ + H2PO2- + H2O →Ni + H2PO3- + 2H+
Uses of Nickel Plating
i) For decorative coating of jewellery, decorative items and automobile spares
ii) For coating of polymers for decorative purpose.
iii) For electronic appliances.
Advantages of electroless plating over electro plating
i) Electricity is not necessary
ii) Complicated parts are uniformly coated
iii) Plastics, glass etc, are easily coated
iv) Good mechanical, chemical and magnetic properties are obtained.
Differences between Electroplating and Electroless plating:
Electroplating Electroless Plating
1. It is done by passing current. It is done by auto catalytic redox reaction.
2. Separate anode is required. Catalytic surface of the object acts as anode.
3. Anode reaction: M →Mn+ + ne- Anode reaction : R →O + ne-
4. Cathode reaction: Mn+ + ne-→M Cathode reaction: Mn+ + ne- →M
5. Irregular objects are not satisfactorily plated All objects are satisfactorily plated.
6. Object to be coated forms the cathode .Object to be coated forms catalytically active surface.
7. It is carried out on conducting materials.It is carried out even on insulators.
55
CY6251 ENGINEERING CHEMISTRY - II
SCE Dept.of S & H
GLOSSARY
CELL: Cell is an assembly of two electrodes and an electrolyte. It consists of two half cells. Each
half cell contains an electrode material in touch with electrolyte.
CURRENT: Current is flow of electricity through a conductor. It is measured in ampere.
55
ELECTRODE: Electrode is a material or a metallic rod/bar/strip which conducts electrons.
ANODE: Anode is an electrode at which oxidation occurs.
CATHODE: Cathode is an electrode at which reduction occurs.
ELECTROLYTIC CELLS: Electrolytic cells are cells in which electrical energy is converted
into chemical energy.
ELECTOCHEMICAL CELLS: Electrochemical cells are cells in which chemical energy is
converted into electrical energy.
SALT BRIDGE: Salt bridge consists of a U – tube containing a gel saturated with KCL or NH4
NO3 in agar – agar. It consists the two half cells of the galvanic cells by the electron movement
through it.
OXIDATION POTENTIAL: Electrode lose electrons
REDUCTION POTENTIAL: Electrode gain electrons.
SINGLE ELECTRODE POTENTIAL: Measure of the tendency of a metallic electrode to lose or
gain electrons, when it is in contact with a solution of its own salt.
STANDARD ELECTODE POTENTIAL: Measure of the tendency of a metallic electrode to
lose or gain electrons, when it is in contact with a solution of its own salt of a 1 molar
concentration at 250C.
ION – SELECTIVE ELECTRODES: These are electrodes which have the ability to respond
only to a particular ion and develop potential, ignoring the other ions in a mixture. The potential
developed by an ion – selective electrodes depends only on the concentration of particular ions.
ELECTROCHEMICAL SERIES: An increasing order of the standard reduction potentials
CORROSION: Corrosion is defined as the gradual destruction of metals by the chemical or
electrochemical reaction with its environment.
PILLING BEDWORTH RATIO; The ratio of the volume of the oxide formed to the volume of
the metal consumed is called ”Pilling – Bed worth ratio” or “Pilling – Bed worth rule”.
PAINT: Paint is a uniform dispersion of finely dived pigments, filters and driers in a liquid
called medium (thinner + vehicle ).When a paint applied to a metal surface , the thinner
evaporates, while the vehicle undergoes slow oxidation forming a pigmented film.
56
CY6251 ENGINEERING CHEMISTRY - II
SCE Dept.of S & H
UNIT-III
ENERGY SOURCES
3.1 INTRODUCTION
Sufficient sources of energy are necessary for industrialized nations. Energy is used for
heating, cooking, transportation and manufacturing. Energy sources can be generally classified as
conventional and non-conventional. Over 85% of the energy used in the world is from
conventional sources such as fossil fuels (coal and oil) and nuclear power.
The convenrtional energy sources depend on coal and oil. The burnt fuels result in the
release of CO2 and other gases into the atmosphere causing environmental damage. There are
abundant renewable sources of energy such as wind, sun, water, and biomass. These sources are
pollution ofree and known as “ green energy “.
3.2 Nuclear Energy :
The enormous energy thus released during the Nuclear Fission & Fusion reaction is
known as Nuclear Energy.
3.2.1 N uclear fission: It is the nuclear reaction in which heavy isotopes are split into
lighter nuclei on bombardment by neutrons. Fission reaction of U235
is given below
3.2.2 Nuclear fusion:
Process of combination of lighter nuclei into heavier nucleus with simultaneous
liberation of largeamount of energy. (e.g) solar system
2 2
1H + 1H→ 2 He + Energy
Nuclear fusion reaction occurs in sun.
3.2.3 Nuclear chain reaction:
235
92U
+ 0n1 → 36Kr
92
+ 56Ba
141 1
+ 3 0n
+ energy
57
CY6251 ENGINEERING CHEMISTRY - II
SCE Dept.of S & H
Differences between fission and fusion reaction
S.No
Nuclear fission
Nuclear fusion
1
It is a process of breaking at
heavier nucleous.
It is a process of
combination of lighter
nuclei.
2
It emits radioactive rays
It does not emit any kind
of radioactive rays
3
The mass number and
atomic number of new
elements are lower than
The mass number and
atomic number of
product is higher than
that of starting elements
4
It occurs at ordinary
temperature
It occurs at high
Temperature
5
It gives rise to chain
reaction
It does not give rise to
chain reaction
6
It emits neutrons
It emits positrons
7
It can be controlled
It canot be controlled
3.3 Nuclear Reactor
3.3.1 Light water nuclear power plant
Definition
Light water nuclear power plant is one in which U235
feed rods are submerged in
water.
Here the water acts as coolant and moderator.
The fission reaction is controlled by inserting or removing the control rods of
B10
automatically.
from the spaces I between the fuel rods.
The heat emitted by
U235
absorbed by the coolant in the fuel core is
Heat is transferred to sea water and then converted into steam.
The steam then drives the turbines, generating electricity.
59
CY6251 ENGINEERING CHEMISTRY - II
SCE Dept.of S & H
(Structure of light water nuclear power plant)
3.3.2 Breeder reactor A nuclear reactor with conversion or multiplication factor greater than one is a breeder
reactor. A
breeder reactor generates fissionable nuclei from fertile
nuclei. E.g., the fertile material like uranium-238 is
converted into fissile
94 Pu239
by using slow neutrons. 94 Pu239
undergoes fission and produces energy.
Working :
`In breeder reactor, 92U235
is used as trigger to produce sufficient neutrons. These
are used to convert 92U235
to Plutonium undergoes fission with the production of three
neutrons. One neutron is used to propagate fission chain. The other two neutrons react with
92U238
to fissionable 94 Pu239
. Thus breeder reactor produces two 239
Pu atoms for
each 238
U consumed. Thus more fissionable material is produced than consumed. Hence
the reactor is called breeder reactor.
Critical Mass:
The minimum amount of fissile material (U235
) required to continue the nuclear chain
reaction is called critical mass.
60
CY6251 ENGINEERING CHEMISTRY - II
SCE Dept.of S & H
w
3.4 Solar Energy
Solar energy
The energy that derive directly from sunlight and can be converted into more
useful forms is known as Solar energy.
3.4.1 Solar Energy Conversion
The energy conversion my occur iterms of heat & current.
3.4.2 Photo galvanic cell or Solar cell
PRINCIPLE: The principle of Solar cell is based on photovoltaic effect. When light radiation falls on
the p-n junction semi conductor device, charge separation takes place and a potential
difference is setup. This causes flow of electrons and produces electricity.
Working: When sun rays all on the top layer of p- type semiconductor, electrons from valence
band are promoted to conductance band and cross the p-n junction into the n-type
semiconductor. A potential difference is set up between the two layers. This causes flow of
electrons and produces electricity. When the „p‟ and „n‟ layers are connected to an external
circuit, electrons flow from „n‟ layer to „p‟ layer and current is generated.
3.4.3 Application of Solar Cell 1. Lighting purpose
Now a days electrical street lights are substituted by solar street lights.
61
CY6251 ENGINEERING CHEMISTRY - II
SCE Dept.of S & H
2. Solar pumps are run by solar battery A large number of solar cells are connected in series to form a solar battery. Solar battery
produces enough electricity to run water pump, etc., They are also used in remote areas
where conventional electricity is not available.
SOLAR BATTERY
3. Solar cells are used in calculators, electronic watches etc.
4. Solar cells are superior to other type of cells, because they are non-polluting and eco-
friendly.
62
CY6251 ENGINEERING CHEMISTRY - II
SCE Dept.of S & H
5. Solar cells are used to drive vehicles.
6. Silicon solar cells are used as a source of electricity in space crafts and satellites.
Advantages of Solar cells
1. Solar cells are used in remote areas, forests and hilly regions.
2. Maintenance cost is minimum.
3. Solar cells are pollution free.
4. They have long life.
Disadvantages
1. Solar cells are costly.
2. Storage of energy is not possible with solar cells.
3.5 WIND ENERGY
Moving air is called wind. Energy recovered from the forces of wind is called wind
energy.
3.5.1 Generation of electricity from wind mill Wind energy is used to generate electricity with the help of wind mills. The crank of
the wind mill is connected to a dynamo. When the blades of wind mill rotate, they turn the
coil of the dynamo and produce electricity. Usually a number of wind mills are erected side-
by-side. The outputs from the wind mills are coupled to generate electricity for commercial
purpose. This type of system is wind energy farms.
Condition: Wind speed should be more than 15km/hr.
Advantages of wind energy
(i) It is cheap and
economical. (ii) It is
renewable
(iii) It does not cause pollution.
Disadvantages
(i) They produce noise.
(ii) Wind farms erected on the migratory routes of birds create
problems. (iii) Wind turbines interfere with electromagnetic
signals.
63
CY6251 ENGINEERING CHEMISTRY - II
SCE Dept.of S & H
3.6 BATTERIES (or) ENERGY STORAGE DEVICES
Battery:
It is an arrangement of several electrochemical cells connected in series that
can be used as a source of direct electric current.
3.6.1 TYPES OF BATTERIES
Secondary battery or secondary cells
In these cells, the electrode reactions can be reversed by passing an external
energy.
They can be recharged by passing electric current.
They are called storage cells or accumulators.
Ex: Lead acid storage cell, Nickel- cadmium cell.
3.6.2 Alkaline Battery
Here the powdered zinc is mixed with KOH and MnO2 to get a gel. A Carbon rod
acts as cathode. IT is immersed in KOH The outside cylindrical body is made up of zinc.
Cell reactions
At anode : Zn (s) + 2OH- → Zn(OH)2 + 2e-
At cathode: 2MnO2 + H2O(l) + 2e- → 2OH- +Mn2O3
Overall : Zn (s) + 2MnO2 + H2O(l) → Zn(OH)2 + Mn2O3
Uses: It is used in calculators, watches etc.,
64
CY6251 ENGINEERING CHEMISTRY - II
SCE Dept.of S & H
3.6.3 Lead storage cell
Description:
It consists of number of voltaic cells connected in series Pb is anode and
PbO2 is cathode
Number of Pb plates and PbO2 plates are connected in parallel.
Plates are separated from adjacent ones by insulators like rubber or glass
fiber.
This arrangement is immersed in dil. H2SO4
Cell reactions
At anode : Pb (s) + SO42-
→ PbSO4 (s) + 2e- +
At cathode: PbO2(s) + SO42-
+ H + 2e- →PbSO4 + 2 H2O
Overall reaction:
Pb (s) + PbO2(s) + 2H2SO4 → PbSO4 + H2O + energy
Uses:
* It is used to supply current mainly in automobiles such as cars. Buses,
trucks, etc.,
* It is also used in gas engine ignition, telephone exchanges, hospitals,
power stations.
3.6.4 Nickel – Cadmium Battery Description
It consists of a cadmium anode. A metal grid containing a paste of NiO2 acting as a cathode.
KOH is electrolyte
Ni-Cd battery
65
CY6251 ENGINEERING CHEMISTRY - II
SCE Dept.of S & H
Cell reactions
At anode: Cd(s) + 2OH- → Cd(OH)2(s) + 2e-
At cathode: NiO2 + 2H2O(l) + 2e- → 2OH- +Ni(OH)2 (s) + energy
Overall reaction:
Cd(s) + NiO2 + 2H2O(l) → Cd(OH)2(s) + Ni(OH)2 (s) + energy
Uses: It is used in calculators. Electronic flash units, transistors and cordless appliances.
3.6.5 Lithium Battery
Description
It consists of a lithium anode and a TiS2 cathode.
A solid electrolyte generally a polymer is packed in
between the electrodes.
The electrolyte permits the passage of ions but not
electrons.
Cell reactions
+
At anode: Li(s) → Li
+ e-
At cathode: TiS2 + e- → TiS2-
Overall reaction:
+
Li(s) + TiS2 → Li
+ TiS2-
Other types of secondary lithium batteries
(i) Li/ MnO2
(ii) Li/V2O5
(iii) Li/MoO2
(iv) Li/Cr3O8
66
CY6251 ENGINEERING CHEMISTRY II
67
SCE Dept.of S&H
.
Advantages of Li battery
It is the cell future. Why?
Its cell voltage is high, 3.0VSince Li is a light weight metal, only 7kg material required to
produce 1mole of electrons.Since all the constituents of the battery are solids, there is no risk of
leakage from the battery. This battery can be made in a variety of shapes and sizes.
Disadvantages of Li
battery
Li battery is more expensive than other batteries
Uses
Button sized batteries are used in calculators, watches, cameras, mobile phones,
laptop computers.
Lithium Battery
It is a solid state battery. Solid electrolyte is
used.
Construction
It has a lithium anode and a TiS2 cathode. A solid electrolyte, a polymer, is
packed in between the electrodes. The polymer electrolyte permits the passage of ions but
not that of electrons.
Working (Discharging)
The anode is connected to cathode through the polymer electrolyte.
Lithium ions and electrons are produced at the anode . The cathode receives the lithium ions
and electrons.
At anode: Li(s) Li+ + e-
At Cathode: TiS2(s) + e TiS2-
CY6251 ENGINEERING CHEMISTRY II
68
SCE Dept.of S&H
Overall reaction: Li(s) + TiS2(s) Li+ + TiS2- LiTiS2
Recharging
The battery is recharged by passing an external current, which drives the lithium
ions back to the anode. The overall reaction is
LiTiS2 Li+
+ TiS2
This cell has a voltage of 3.oV.
Uses:
It possesses very small size and high energy density. So it is used in calcutors,
electronic flash units, computers, transistors head phones etc.
Advantages
(i) The cell has a voltage of 3.0V.
(ii) Li is a light-weight metal. Just 7g (1 mole) of Li is required to produce 1 mole of
electrons.
(iii) Li has the most negative Eo value. So it gives a higher voltage than other cells. (iv)
It is a total solid state battery. There is no risk of current leakage from the battery. (v)
It is manufactured in a variety of sizes and shapes.
Disadvantages
It is more expensive than other batteries.
3.7 FUEL CELLS:
Definition
Fuel cell is a voltaic cell. It converts chemical energy of the fuels directly into
electricity without combustion. In these cells, the reactants and electrolytes are continuously
supplied to the cell.
Fuel + Oxygen Oxidation products + Electricity.
Examples : Hydrogen - oxygen fuel cell.
3.7.1 Hydrogen - oxygen fuel cell
It is the simplest and most successful fuel cell. The fuel-hydrogen and the oxidiser-
oxygen and the liquid electrolyte are continuously supplied to the cell.
Description
The cell has two porous electrodes, anode and cathode. The electrodes are made of
CY6251 ENGINEERING CHEMISTRY II
69
SCE Dept.of S&H
compressed carbon containing a small amount of catalyst (Pt, Pd, Ag). Between the two
electrodes an electrolytic solution, 25% KOH is filled
Working
Hydrogen passes through the anode compartment, where it is oxidised. Oxygen
passes through the cathode compar tment, where it is reduced.
(Hydrogen – Oxygen fuel cell)
Cell reactions At anode: 2H2+4OH-
4H2O +4e- At cathode: O2 +2H2O + 4e-
4OH Overall cell
reaction: 2H2+O 2 2H2O
emf of the cell = 0.8 to 1.0V
Advantages of Fuel Cells 1. They are efficient and instant in operation.
2. They are pollution free.
3. They produce electric current directly from the reaction of a fuel and an oxidiser.
4. They are light in weight
Disadvantages 1. Fuel cells cannot store electric energy.
2. Electrodes are expensive and short lived.
3. H2 should be pure.
Applications 1. H2 - O2 fuel cells are used in space crafts, submarines to get electricity
2. In H2 - O2 fuel cell, the produt water is a valuable source of fresh water for astronauts
CY6251 ENGINEERING CHEMISTRY II
70
SCE Dept.of S&H
Glossary
Nuclear fission
The process of splitting of heavier nucleus into two or more smaller nuclei with
simultaneous liberation of large amount of energy is called Nuclear Fission.
Nuclear Fusion
The process of combination of lighter nuclei into heavier nuclei, with simultaneous
liberation of large amount of energy is called Nuclear Fusion.
Nuclear Chain Reaction
A fission reaction, where the neutrons from the previous step continues to propagate
and repeat the reaction is called Nuclear Chain Reaction.
Breeder reactor
Breeder reactor is the one which converts non-fissionable material ( U238
, Th232
) into
fissionable material ( U235
, Pu239
). Thus the reactor produces or breeds more fissionable
material than it consumes.
Fissionable nucleides (or ) Fissile nucleides
The nucleides like U235
, Pu239
which undergo fission reaction is known as Fissle
nucleides.
Non- fissionable nucleides (or) Fertile nucleides
The nucleides like U238
, Th232
which do not undergo fission reaction is known as
Fertile nucleides.
Critical Mass:
The minimum amount of fissile material (U235
) required to continue the nuclear
chain reaction is called critical mass.
Solar energy
The energy that derive directly from sunlight and can be converted into more
useful forms is known as Solar energy.
Photogalvanic cell
Photogalvanic cell is one, which converts the solar energy (energy obtained from the
sun ) directly into electrical energy.
Wind energy
Moving air is called wind. The energy possessed by wind is because of its high speed.
The wind energy is harnessed by making use of wind mills, sky sail, ladder mill, kite ship etc.
Fuel cell
Fuel cell is a voltaic cell which converts the chemical energy directly into electricity
without combustion. In these cells, the reactants, products and the electrolytes pass through the
cell.
Battery
Battery is an arrangement of several electrochemical cells connected in series that can
be used as a sources of direct electric current.
Electrolytic Cell
Electrolytic Cell converts electrical energy into chemical energy. Eg. Decomposition
of water into hydrogen and hydroxide ion.
Electrochemical Cell
Electrochemical Cell converts chemical energy into electrical energy. Eg. Galvanic (or)
Voltaic cell.
CY6251 ENGINEERING CHEMISTRY II
71
SCE Dept.of S&H
UNIT – IV
ENGINEERING MATERIALS
4.1 INTRODUCTION
Materials which are used in manufacturing of wools and equipments and in construction
of buildings, where very specific requirements are needed are called engineering materials.
These include cement, refractories, abrasives, lubricants, etc,
4.2 ABRASIVES Abrasives are very hard substances used for grinding, shaping and polishing
other materials
4.2.1 PROPERTIES
Have very high melting point
Chemically inert
High abrasive power (ability to scratch away pr sharp other materials)
Sometimes hard and brittle or soft and flexible
4.2.2 CLASSIFICATION OF ABRASIVES – TYPES &
4.2.3 APPLICATIONS OF ABRSASIVES
natural abrasives – Eg. Diamond, corundum
synthetic abrasives – Eg. carborundum, norbide
Hardness is measured in terms of moh‟s scale.
Diamond is taken as the reference and hardness of other materials are determined
abrasives with Mohr‟s scale 1-4 are called soft abrasives
NATURAL ABRASIVES
Diamond:
Purest crystalline carbon - Hardest natural substance
Mohr‟s scale value is 10 -Superior chemical inertness
Used in grinding wheels, drilling tools, cutting glasses, etc
Corundum
Pure crystalline form of alumina - Mohr‟s scale value is 9 - Used in grinding glass, gems etc.
Emery
55-75% alumina, 20-40% magnetite, 12% others - Black and opaque
-Mho‟s scale value is 8 - Used for making abrasive paper, abrasive cloth, etc.
Quartz
Pure silicone - Mohr‟s scale value is 7 - Used in painting industries
Garnet
Trisilicates of alumina, magnetite and Fe oxide used for the manufacture of abrasive paper
and cloth.
ARTIFICIAL ABRASIVES
Silicon Carbide (SiC)
Manufacture Silicon Carbide is manufactured by heating sand (60%)and coke (40%) with some
saw dust
and a little salt in an electric furnace to about 1500°C
CY6251 ENGINEERING CHEMISTRY II
72
SCE Dept.of S&H
SiO2 + 3C gives SiC + 2CO
The silicon carbide removed from the furnaces, is then mixed with bonding
agent(clay, silicon nitride) and than shaped, dried and fired.
Properties 1. Silicon carbide possesses a high thermal conductivity, low expansion and high
resistance
to abrasion and spalling.
2. They are mechanically strong. Mohr‟s scale value is 9.
3. Bear very high temp. 1650°C
4. Has thermal conductivity between metals and ceramics –
They are electrically intermediate between conductors and insulators.
Uses 1. Silicon carbide are used as heating elements in furnaces in the form of rods or bars.
2. They are also used for partition wall of chamber kilns, coke ovens, muffle furnaces
and floors of heat treatment furnaces.
3. Sic bonded with tar are excellent for making high conductivity crucible.
Norbide or Boran Carbide (B4C)
Manufacture It is prepared by heating a mixture of boran oxide (B2O3) and coke in an electric furnace to
about 2700°C
B2O3 +7C give B4C + 6CO
Properties
1. Its hardness is 9 on Mohr‟s scale.
2. It is light weight and black colored compound.
3. It is highly resistant to chemical attack and erosion.
4. It resists oxidation much better than diamond.
Uses
It is used as hard materials for making grinding dies, and for cutting and
sharpening hard high speed tools.
It is used to prepare scratch and wear resistant coating.
4.3 REFRACTORIES Materials that can withstand high temp without softening and deformation in their
shape.Used for the construction of furnaces, converters, kilns, crucibles, ladles etc.
4.3.1 CHARACTERISTICS
Infusible at operating temp.
Chemically inert towards corrosive gases, liquids etc. Should not suffer change
in size at operating temp. Should have high refractoriness
Should have high load bearing capacity at operating temp.
4.3.2 CLASSIFICATION Based on chemical nature
Acidic refractories – Eg. Silica and Alumina
CY6251 ENGINEERING CHEMISTRY II
73
SCE Dept.of S&H
Basic refractories – Eg. Magnesite and Dolomite
Neutral refractories – Eg. Graphite and Carborundum
Based on refractoriness
Low heat duty refractories
Intermediate heat duty
refractories
High heat duty refractories
Super heat duty refractories
4.3.3 PROPERTIES Refractoriness It is the ability to withstand very high temp. without softening or deformation
under particular service condition. Since most of the refractories are mixtures of
several metallic oxides, they do not have a sharp melting point. So the refractoriness
of a refractory is generally measured as the softening temperature and is expressed in
terms of pyrometric cone equivalent.(PCE). Pyrometric cone equivalent is the
number which represents the softening temperature of a refractory specimen of
standard dimension (38mm height and 19mm triangular base) and composition.
Objectives of PCE test
To determine the softening temperature of a test refractory material.
To classify the refractories
To determine the purity of the refractoreies
To check whether the refractory can be used at particular servicing temperature.
Refractoriness is determined by comparing the softening temperature of a test cone
with that of a series of segar cones. Segar cones are pyramid shaped standard refractory of
definite composition and dimensions and hence it has a definite softening temperature.
A test cone is prepared from a refractory for which the softening temperature
to be determined, as the same dimensions of segar cones. Then the test cone is placed in
electric furnace. The furnace is heated at a standard rate of100C per minute, during which
softening of segar cones occur along with test cone. The temperature at which the apex of the
cone touches the base is taken as its softening temperature.
RUL – Refractoriness Under Load The temp. at which a std dimensioned specimen of a refractory undergoes 10%
deformation
with a constant load of 3.5 or 1.75 Kg/cm2
The load bearing capacity of a refractory can
be measured by RUL test. A good refractory should have high RUL value
Porosity – ratio of pore volume to the bulk
volume
P = (W- D/W- A) X
100
W – weight of saturated specimen in
air
D – weight of dry specimen
CY6251 ENGINEERING CHEMISTRY II
74
SCE Dept.of S&H
A – weight of saturated specimen in water
Porosity reduces strength, corrosion resistance thermal conductivity, thermal spalling
and abrasion resistance
Thermal spalling – property of breaking, cracking or peeling of refractory material
under high temp. Thermal spalling may be due to rapid change in temp. or slag penetration.
A good refractory should show good resistance to thermal spalling
Dimensional stability Resistance of refractory to any volume change when exposed to high temp. over a
prolonged time. Refractories may undergo reversible or irreversible dimensional changes
A good refractory should show minimum level of reversible dimensional changes with temp.
4.3.4 MANUFACTURING OF REFRACTORIES
ALUMINA BRICKS Contain 50% of aluminium oxide
Manufacture
Calcined bauxite, silica and grog (calcined fire clay) are ground well and mixed
with water. The pasty mass is converted into bricks by mechanical pressing or slip
casting.The bricks are dried and fired at about 1200 to 14000 C for 6-8 days
MAGNESITE BRICKS Contain maximum Magnesium oxide
Manufacture Calcined magnesite, magnesia or iron oxide are ground well and mixed with water. The pasty
mass is converted into bricks by mechanical pressing or slip casting. The bricks are dried and
fired at about 15000 C for 8 hours then cooled slowly
ZIRCONIA BRICKS
Contain zirconite
Manufacture
Zirconite mineral, colloidal zirconia or alumina are ground well and mixed with water and
made into bricks. Small amount of MgO or CaO is added as stabilizer. The bricks are dried
and fired at about 17000 C
4.4 PORTLAND CEMENT
It is defined as an extremely finely ground product.
It is obtained by heating a mixture of argillaceous (clay containing ) and calcareous (lime
containing ) raw materials to about 1500 c. It is then mixed with gypsum to increase the quick setting
and hardening property.
4.4.1 CHEMICAL COMPOSITION OF PORTLAND CEMENT 3CaO.SiO2 - Tri calcium Silicate
3CaO.Al2O3 - Tri calcium Aluminate
4CaO.Al2O3.Fe2O3 - Tetra calcium alumino Ferrate
CY6251 ENGINEERING CHEMISTRY II
75
SCE Dept.of S&H
4.4.2 MANUFACTURE OF PORTLAND
CEMENT
Raw materials :
(i) Calcareous materials , CaO Ex: Limestone, chalk.
(ii) Argillaceous materials, Al2O3 and SiO2 Ex: clay, slate etc
(iii) Powdered coal (or) fuel oil.
(iv) Gypsum (CaSo4.2H2O)
Manufacture of Portland cement involves the following
steps:
(i) Mixing of raw materials
(ii) Burning
(iii) Grinding
(iv) Storage and Packing
(i) Mixing of raw materials:
(a) Dry Process (b) Wet Process
(a) Dry Process: In dry process, the raw materials like limestone and clay(3:1) are dried,
and mixed in definite proportions
(b) Wet process : In wet process, the raw materials in definite proportions are finely ground
with water and the slurry ( past like) is fed at the top of the rotary kiln.
(II) Burning
The burning process is usually done in rotary kiln which is a long horizontal steel cylinder
coated with refractory bricks and capable of rotating at 1 rpm 9 Revolution per minute) . The
rotary kiln is set at a slight inclination of about 5-60
in order to allow the raw materials fed at one
end to travel slowly to the firing and discharge exit end.
The slurry of raw materials is allowed to enter from the top end of the rotary kiln.
Simultaneously the burning fuel ( like powdered coal or oil) and air are introduced from the
lower end of kiln . The slurry gradually comes down in the kiln into the different zones ( Drying
Zone at
CY6251 ENGINEERING CHEMISTRY II
76
SCE Dept.of S&H
400o
:Calcination zone at 700 -1000 o
C and clinkering zone at 1250-1500 o
C of
increasing temperatures.
(a) Drying Zone: The upper part of the rotary kiln is known as drying zone
,where the temperature is about 400 o
C . Due to the presence of hot gases in
this zone, water is evaporated from the slurry.
(b) Calcinations zone: The middle part of the rotary kiln is known as calcining zone
where the temperature ranges from 700 -1000 o
C. In this zone lime stone is
decomposed into CaO and CO2
CaCO3 700 -1000 o
C CaO +CO2
Lime Stone Quick lime
(c) Clinkering Zone : The lowest part of the zone is called as clinkering zone, where
the temperature is maintained about 1250-1500 o
C. In this zone lime reacts with clay (
Containing Al2O3, Fe2O3 and SiO2) and forms aluminates and silicates
2CaO+ SiO2 -------- 2CaO.SiO2
Di calcium Silicate
3CaO+ SiO2 -------- 3CaO.SiO2
Tri calcium Silicate
The mixture is then finely powdered and fed into the top of the rotary kiln.
3CaO+ Al2O3-------- 3CaO.Al2O3
Tri calcium Aluminate
4CaO + Al2O3 + Fe2O3--------- 4CaO.Al2O3.Fe2O3
Tetra calcium alumino Ferrate
(ii) Cooling : the hot clinker is cooled with atmospheric air and the hot air thus
produced is used for drying the coal before grinding.
(iii) Grinding : The cooled clinker is then finely pulverized with 2-6% gypsum acts as
a retarding agent for quick setting of cement.
(iv) Storage and Packing: The cement coming out from the grinding mills is stored in
a concrete storage silos. Then the cement is packed in jute bags by automatic
machines. Each bag contains 50kgs of cement.
PROPERTIES
4.4.3 SETTING AND HARDENING OF CEMENT:
When the cement is mixed with water, hydration and hydrolysis of cement begin, resulting
in the formation of gel and crystalline products.
Setting: It is defined as the stiffening of the original plastic mass, due to initial gel
formation. Hardening: It is defined as the development of strength, due to crystallization.
Chemical reactions involved in setting and hardening of cement:
When water is mixed with cement , hydration of tricalcium aluminate occurs rapidly and
the paste becomes quite hard within a short time. This process is known as initial setting of cement.
3CaO.Al2O3 +6H2O-------3CaO.Al2O3.6H2O
Role of gypsum in cement:
(i) In initial setting process gypsum is added during grinding of cement clinkers to retard the rapid
hydration
CY6251 ENGINEERING CHEMISTRY II
77
SCE Dept.of S&H
of C3A. Gypsum reacts with C3A to form insoluble calcium sulphoaluminate complex.
C3A + 3CaSO4.2H2O--------C3A.3CaSO4.2H2O
(ii) After the hydration of C3A,C3S begins to hydrate to give tobermonite gel and crystalline
Ca(OH)2. The hydration of C3S takes place within 7days.
2(3CaO.SiO2) + 6H2O--------- 3CaO.2SiO2.3H2O + 3Ca(OH)2 + 500kj/kg
(iii) Dicalcium silicate reacts with water slowly and gets finished 7-28days.
2(2CaO.SiO2) + 4 H2O -------- 3CaO.2SiO2.3H2O +Ca(OH) 2 + 250kj/kg
(iv) Hydration of tetra calcium aluminoferritetakesplace initially, the hardening takes
place finally through crystallization along with C2 S.
4CaO.Al2O3.Fe2O3 + 7H2O----------3CaO.Al2O3.6H2O + CaO.Fe2O3.H2O + 420KJ
Crystalline gel
Thus the final setting and hardening of cement is due to the formation of tobermonite gel
plus crystallization of Ca(OH)2 and hydrated tricalcium aluminate.
4.4.4 OTHER TYPES OF CEMENT - SPECIAL CEMENT
Water Proof Cement :
It is obtained by adding water proofing agents like calcium stearate and gypsum
with tannic acid to ordinary Portland cement during grinding.
Functions of water- Proof cement:
Functions of water- proof cement
(i) To make concrete impervious to water under
pressure.
(ii) To resist the adsorption of water.
White cement or White Portland cement
It is obtained by heating the raw materials free from iron oxides. It is white in
color due to the absence of ferric oxide.
It issued for making tiles, mosaic works with some coloring agents like
yellow ochre, Venetian red etc. It is used for repairing and joining marble pillars and
blocks.
4.5 GLASS
Glass is an amorphous, hard brittle, transparent, super cooled liquid of infinite
viscosity.
Glass may be represented as xR2O.yMO.6SiO2
4.5.1 GENERAL PROPERTIES OF GLASS:
1. It is amorphous.
2. It is very brittle.
3. It softens on heating.
4. It has no definite melting point.
5. It is affected by alkalis.
CY6251 ENGINEERING CHEMISTRY II
78
SCE Dept.of S&H
6. It is a good electrical insulator.
7. It can absorb, reflect or transmit light.
8. It is not affected by air water, acids and chemical agents.
4.5.2 MANUFACTURE OF GLASS
1. Melting :
The raw materials in proper proportions are mixed and finely powdered.This
homogeneous mixture is known as BATCH is fused with some broken glass called
CULLET in the pot of the furnace.The furnace is heated by burning producer gas and air
mixture over the charge. The cullet melts at a low temp and assists in melting the rest of the
charge.
CaC O3 + Si O2------ CaSiO3 + CO2
Na2C O3 + Si O2----- Na2Si O3 + CO2
Forming and Shaping
The molten glass is then worked into articles of desired shapes by either blowing or
moulding or pressing between rollers.
Annealing:
Glass articles are then allowed to cool gradually to room temperature. Suddencooling must be
avoided, because cracking occurs.Longer the annealing period, the better is the quality of the glass.
Finishing:
All glass articles after annealing, are subjected to finishing processes such as
(a) Cleaning (b) grinding (c) polishing (d) cutting (e) sand blasting
4.5.3 TYPES AND USES OF GLASSES
1.Soda-lime or soda glass
(i) Raw materials: Silica , calcium carbonate and soda ash
(ii) Composition: Na2O. CaO. 6SiO2
Properties (a) They are low in cost.
(b) They are resistant to water
(c) They are attacked by common reagents like acids.
(d) They melt easily‟
2. Potash lime or Hard glass
(i) Raw materials : Silica, CaCO3, K2CO3
(ii) Composition: K2O.
CaO.6SiO2
Properties:
(a) They have high melting
point.
(b) They do not fuse easily.
CY6251 ENGINEERING CHEMISTRY II
79
SCE Dept.of S&H
(c) They are less acted upon acids alkalis, solvents.
Uses: Used for manufacturing combustion tubes, chemical apparatus
3. Lead glass or Flint glass
(i) Raw materials: Lead
oxide, silicva, K2O
(ii) Composition:
K2O.PbO.6SiO2
Properties:
(a) It is bright and lustrous
(b) It has high specific gravity. (3 to 3.3)
(c) It is more expensive to manufacture.
(d) It has a lower softening temperature than soda glass.
(e) It has higher refractive index.
Uses: (a) These are used for high quality tablewares.
(b) They are used in neon sign tubings, optical lenses, electrical insulators, cathode ray tube.
2. Potash lime or Hard glass
(i) Raw materials : Silica, CaCO3, K2CO3
(ii) Composition: K2O.
CaO.6SiO2 (iii)
Properties:
(a) They have high melting
point.
(b) They do not fuse easily.
(c) They are less acted upon acids alkalis, solvents.
Uses: Used for manufacturing combustion tubes, chemical apparatus
3. Lead glass or Flint glass
(i) Raw materials: Lead oxide, silicva, K2O
(ii) Composition: K2O.PbO.6SiO2
Properties:
(a) It is bright and lustrous
(b) It has high specific gravity. (3 to 3.3)
(c) It is more expensive to manufacture.
(d) It has a lower softening temperature than soda glass.
(e) It has higher refractive index.
Uses: (a) These are used for high quality tablewares.
(b) They are used in neon sign tubings, optical lenses, electrical insulators, cathode ray tube.
CY6251 ENGINEERING CHEMISTRY II
80
SCE Dept.of S&H
4. Borosilicate glass or Pyrex glass or Jena glass
(i)Raw materials: Silica, borax with small amount of alumina and some oxides.
(ii) Composition : SiO2 (80.5%); B2O3 (13%)
Al2O3 (3%) K2O (3%) Na2O (0.5%)
(iii) Properties:
(1) It possess low thermal coefficient of expansion and high chemical resistance.
(2)It possesses very high softening points and excellent resistivity.
Uses: It is used in industry for pipe lines for corrosive liquids, gauge glasses,
5. Alumina silicate glass
Raw materials: It has 5% or more alumina
(i)Composition: SiO2 Al2O3, B2O3, MgO, CaO, Na2O K2O
Properties:
They possess high softening temperature.
Uses: (a)Used in high pressure mercury discharge tubes
(b)Chemical combustion tubes.
6. Optical or Crookes glass
Raw materials: It contains phosphorus, lead silicate with small amount of cerium oxide.
Properties:
(a) Cerium oxide present in the glass absorbs uv light,
(b) They have low melting point.
Uses: optical glasses are used for making lenses.
7. Glass wool Glass wool is fibrous wool like material It is composed of intermingled fine threads
or filaments of glass.
Properties: It is a very good heat and fire proof materials
Its electrical conductivity is low.
Uses; It is used for heat insulation purposes
It is used for electrical and sound insulation.
Glossary
Abrasives
Abrasives are hard substances, used for polishing, shaping, grinding operations. They
are characterized by high melting point, high hardness and chemically inactive.
Refractories
Refractories are materials that can withstand high temperatures without softening or
deformation in shape.
Refractoriness
Refractoriness is the ability of a material to withstand very high temperature without
softening or deformation under particular service condition.
Pyrometric cone equivalent
Pyrometric cone equivalent is a number which represents the softening temperature of a
refractory specimen of standard dimension ( 38 mm height and 19 mm triangular base ) and
composition.
RUL ( Refractoriness Under Load )
CY6251 ENGINEERING CHEMISTRY II
81
SCE Dept.of S&H
The temperature at which the refractory deforms by 10% under a load of 3.5kg/cm2 is
called RUL (Refractoriness Under Load)
Porosity
Porosity is defined as the ratio of its pore volume to the bulk volume
Thermal spalling
Thermal spalling is the property of breaking, cracking or peeling off a refractory
material under high temperature. A good refractory must show a very good resistance to
thermal spalling.
Calcination
Heating the ore in absence of air is called Calcination
Cement
Cement is a material with adhesive and cohesive properties which make it capable of
bonding minerals fragments into a compact whole. The name “Portland cement” given
originally due to the resemblance of the colour and quality of the hardened cement to Portland
sonte ( Portland island is England).
CY6251 ENGINEERING CHEMISTRY II
82
SCE Dept.of S&H
UNIT V
FUELS AND COMBUSTION
5.1 DEFINITION Fuel is a combustible substance ,during combustion of it the atoms of C,H,S and
N etc are combine with oxygen with simultaneous liberation of heat and light.
Ex: C + O2 CO2 +94 K cals
2H2+O2 2H2O +68.5 K cals
5.1.1 CHARACTERISTICS FOR GOOD FUEL
High calorific value.
Moderate ignition temperature.
Low moisture content.
Low contents of non-combustible matters.
Combustion should be controllable.
Easy to transport and readily available at low cost.
Solid Liquid Gas Solid Liquid Gas
5.2.1 Calorific value:
. It is defined as the amount of heat liberated by the complete combustion of a unit mass
of the fuel.
5.2.2 Gross or high calorific value (GCV)
It is defined as the total heat generated when a unit quantity of fuel is
completely burnt and the products of combustion are cooled to room temperature.
5.2.3 Net or Lower Calorific Value(NCV)
It is defined as the “net heat produced when a unit quantity o f fuel is
completely burnt and the products of combustion are allowed to escape.
CY6251 ENGINEERING CHEMISTRY II
83
SCE Dept.of S&H
NCV = GCV- latent heat of condensation of steam produced.
5.2.4 Theoretical calculation of calorific value ( Dulong‟s formula)
According to Dulong, the calorific value of a fuel is the sum of the calorific
values of its constituent elements.
The calorific values of C, H&S are found to be 8080, 34500 and 2240kcals
when 1kg of the fuel is burnt completely.
Thus,Dulong‟s formulae for GCV is written as
GCV=1/100 [8080(C)+34500(H-O/8)+2240(S)]Cals/kg.
NCV =[ GCV-9/100( H)x 587] Kcals/kg.
The latent heat of steam is 587Kcals/kg.
In Dulong‟s formula C, H, O&S represent the percentage of the corresponding
elements.
5.3 SOLID FUEL
5.3.1 ADVANTAGES OF SOLID FUELS:
Solid fuels are easily available and they are cheap.
Handling and transportation are easy.
They can be stored conveniently without any risk.
They have a moderate ignition temperature.
5.3.2 DISADVANTAGES OF SOLID FUELS:
Combustion process cannot be easily controlled.
The calorific value is comparatively lower.
They form large amount of ash and its disposal is a big problem.
A large space is required for storage.
5.4 COAL
Analysis of coal
5.4.1 Proximate Analysis:
It involves the determination of percentage of following in coal
a. Moisture content
b. Volatile matter
c. Ash content
d. Fixed carbon
(a) Moisture content
1. 1gm of powdered and air-dried coal sample in crucible is heated at 100-
150⁰C in an electric air oven for 1 hour.
2. The loss in weight of the sample is found out and percentage of moisture is
calculated as
% of moisture = Loss in weight of coal ×100
Weight of air-dried coal
(b) Volatile matter:
CY6251 ENGINEERING CHEMISTRY II
84
SCE Dept.of S&H
In this the crucible with residual coal sample is covered with a lid and heated at
950± 20⁰C for 7mins in a muffle furnace. The loss in weight is found out.
% of volatile matter = Loss in weight of coal ×100
Weight of moisture free coal
(c) Ash Content:
The crucible with residual coal sample is heated without lid at
700 ± 50 ⁰C for ½hour in a muffle furnace. The loss in weight is found out.
% of ash content = weight of ash formed x100
Weight of dried coal
(d) Fixed Carbon:
% of fixed carbon = percentage of (a+b+c)
5.4.2 Significance of proximate analysis:
1. High percentage of moisture content is undesirable because
2. High percentage of volatile matter is undesirable because
3. High percentage of ash content is undesirable because
4. High percentage of fixed carbon content is desirable because
5.5 CARBONISATION OFMETALLURGICAL COKE
When coal is heated strongly in the absence of air , it is converted into lustrous,
dense, porous and coherent mass known as coke. This process of converting coal is known as
carbonization.
5.5.1 METALLURGICAL COKE
When bituminous coal is heated strongly in the absence of air, the volatile matter
escapes out and the mass becomes hard, porous and coherent which is called Metallurgical
coke.
PREPARATION
5.5.2 Otto-Hoffman’s method
Significance of Otto-Hoffman‟s method
(i) To increases the thermal efficiency of the carbonization process and,
(ii) To recover the valuable by products (like coal gas, ammonia, benzyl oil,
etc).
CY6251 ENGINEERING CHEMISTRY II
85
SCE Dept.of S&H
. The oven consists of a number of silica chambers , each chamber is provided with a
charging hole at the top, it is also provided with a gas off take valve and iron door at
each end for discharging coke.
Coal is introduced into the silica chamber and the chambers are closed.
The chambers are heated to 1200 o C by burning the preheated air and the producer gas
mixture in the interspaces between the chambers.
The air and gas are preheated by sending them through 2nd
and 3rd
hot regenerator.
Hot flue gases produced during carbonization are allowed to pass through 1st and 4
th
regenerators until the temperature has been raised to 1000ċ.
While 1st and 4
th regenerated are heated by hot flue gases, the 2
nd and 3
rd regenerators
are used for heating the incoming air and gas mixture.
When the process is complete, the coke is removed and quenched with water.
The yield of coke is about 70%.
The valuable by products like coal gas, tar, ammonia, H2S and benzyl, etc. can be
recovered from flue gas.
5.5.3 Recovery of by-products
(i) Tar
The flue gases are first passed through a tower in which liquor ammonia is sprayed.
Tar and dust get dissolved and collected in a tank below
(ii) Ammonia
The gases are then passed through another tower in which water is sprayed. Here
ammonia gets converted to NH4OH.
(iii) Naphthalene
The gases are again passed through a tower, in which cooled water is sprayed,
naphthalene gets condensed.
(iv) Benzene
The gases are passed through another tower, where petroleum is sprayed, benzene
gets condensed to liquid.
(v) Hydrogen Sulphide
The remaining gases are then passed through a purifier packed with moist Fe2O3.
Here H2S is retained.
The final gas left out is called coal gas which is used as a gaseous fuel.
5.5.4 Advantages of Otto Hoffman’s process
1. Valuable by products like ammonia, coal gas, Naphthalene etc. are recovered.
2. The carbonization time is less.
3. Heating is done externally by producer gas.
5.6 IQUID FUELS
5.6.1 ADVANTAGES OF LIQUID FUELS:
They have higher calorific value than solid fuel.
They occupy less storage space than solid fuels.
Their combustion is uniform and easily controllable.
Liquid fuels do not yield any ash after burning.
DISADVANTAGES OF LIQUID FUELS:
Liquid fuels are more costly than the solid fuels.
Liquid fuels give unpleasant odor during incomplete combustion.
Special type of burners is required for effective combustion.
Some amount of liquid fuels will escape due to evaporation during storage.
CY6251 ENGINEERING CHEMISTRY II
86
SCE Dept.of S&H
5.6.2 PETROLEUM
It is naturally occurring liquid fuel.
It is dark brown or black coloured viscous oil
Crude oil is a mixture of paraffinic, olefinic and aromatic hydrocarbons with small
amounts of organic compounds like N, O and S.
The average composition of crude oil is as follows
C = 80-87%
H = 11-15%
S = 0.1-3.5%
N+O = 0.1-0.5%
It is classified into three types
1. Paraffinic-Base type crude oil
It contains saturated hydrocarbons from CH4 to C35H72 with a smaller amount of
naphthenes and aromatics.
2. Naphthenic or Asphaltic Base type crude oil
It contains Cycloparaffins or naphthenes with a smaller amount of paraffin and
aromatics
3. Mixed base type crude oil
It contains both paraffinic and asphaltic hydrocarbons.
5.6.3 REFINING OF PETROLEUM OR CRUDE OIL
The crude oil obtained from the earth is a mixture of oil, water, unwanted impurities
and its subjected to fractional distillation.
During fractional distillation, the crude oil is Thus, the process of removing impurities
and separating the crude oil into various fractions having different boiling points is
called Refining of Petroleum.
The process of refining involves the following steps.
Step 1: Separation of water (Cottrell‟s process)
The crude oil well is an extremely stable emulsion. The crude oil is allowed to flow
between two highly charged electrodes, where colloidal water droplets combine to form large
drops, which is then separated out form the oil.
Step 2: Removal of harmful sulphur compounds
Sulphur compounds are removed by treating the crude oil with copper oxide. The
copper sulphide formed is separated out by filtration.
Step: 3 Fractional distillation
The purified crude oil is then heated to about 400ċ in an iron retort, where the oil gets
vaporized.
The hot vapors are then passed into the bottom of a “fractionating column”.
The fractionating column is a tall cylindrical tower containing a number of horizontal
stainless steel trays at short distances.
Each tray is provided with small chimney covered with a loose cap.
When the vapors of the oil go up in the fractionating column, they become and get
condensed at different trays.
The fractions having higher boiling points condense at lower trays whereas the
fractions having lower boiling points condense at higher trays.
The gasoline obtained by this fractional distillation is called straight-run gasoline.
Various fractions obtained at different trays are given in table.
CY6251 ENGINEERING CHEMISTRY II
87
SCE Dept.of S&H
5.7. KNOCKING
The rate of ignition of the fuel gradually increases and the final portion of the fuel-air
mixture gets ignited instantaneously producing an explosive sound known as “Knocking”.
5.7.1 Causes of knocking in S.I (Petrol) engines
In a petrol engine fuel used as a mixture of gasoline vapor and air at 1:17 ratio
The mixture is compressed and ignited by an electric spark.
The products of combustion increase the pressure and push the piston down the
cylinder.
If the combustion proceeds in a regular way, there is no problem in knocking.
But in some cases, the rate of combustion (oxidation) will not be uniform due to
unwanted chemical constituents of gasoline.
Knocking property of the fuel reduces the efficiency of engine. So a good gasoline
should resist knocking.
5.7.2 Improvement of anti knock characteristics
(i) Blending petrol of high octane number with petrol of low octane number, so that the
octane number of the latter can be improved.
(ii) The addition of anti-knock agents like Tetra-Ethyl Lead (TEL).
5.7.3 OCTANE NUMBER OR OCTANE RATING
Thus octane number is defined as „the percentage of iso-octane present in a
mixture of iso-octane and n-heptanes.‟Octane number is introduced to express the
knocking characteristics of petrol. On the other hand, iso-octane gives very little
knocking and so, its anti-knock value has been given 100.
CH3 CH3 -CH-CH2-C-CH3 CH3-CH2-CH2-CH2-CH2-CH2-CH3 CH3 N-heptanes (Octane no = 0) CH3 Iso-octane (Octane no = 100) 5.7.4ANTI-KNOCK AGENT Tetraethyl lead (TEL) (C2H5)4 Pb is an important additive added to petrol. Thus the
petrol containing tetra ethyl lead is called leaded petrol. TEL reduces the knocking tendency
of hydrocarbon.
Mechanism of Knocking
. Knocking follows a free radical mechanism, leading to a chain growth which results in
an explosion.
If the chains are terminated before their growth, knocking will cease.
TEL decomposes thermally to form ethyl free radicals which combine with the growing
free radicals of knocking process and thus the chain growth is stopped.
Disadvantages of using TEL
When the leaded petrol is used as a fuel, the TEL is converted to lead oxide and
metallic lead.
To avoid this, small amount of ethylene dibromide is added along with TEL.
This ethylene dibromide reacts with Pb and PbO to give volatile lead bromide, which
goes out along with exhaust gases and creates atmospheric pollution.
But now a day‟s aromatic phosphates are used instead of TEL.
CY6251 ENGINEERING CHEMISTRY II
88
SCE Dept.of S&H
5.7.5Causes of knocking in CI (Diesel) engines
In a diesel engine, first air is compressed and raises the temperature of the cylinder to
about 500ċ then the oil is sprayed.
The expanding gases push the piston and power stroke begins.
The combustion of a fuel in a diesel engine is not instantaneous and the time
between injection of the fuel and its ignition is called Ignition lag or Ignition delay and
raising the temperature of vapour to its ignition temperature.
.
Which undergo explosion during ignition ,this is responsible for diesel knock.
5.7.6 CETANE NUMBER OR CETANE RATING
Thus the cetane number is defined as “the percentage of cetane present in a
mixture of cetane and 2-methyl naphthalene which has the same ignition lag as the
fuel under test”.
Cetane number is introduced to express the knocking characteristics of diesel.
Cetane (C16H34) has a very short ignition lag and hence its cetane number is taken as
100.
On the other hand 2-methyl naphthalene has a long ignition lag and hence
its cetane number is taken zero.
CH3
CH3-(CH2)14-CH3
n-cetane (cetane no = 100)
2-methyl naphthalene (cetane no = 0)
The cetane number decreases in the following order.
Straight chain paraffin‟s >Cycloparaffins >Olefins >Branched paraffin‟s.
The cetane number of diesel oil can be increased by adding additives called dopes.
Ex: Ethyl nitrate, Iso-amyl nitrate.
5.7.8 DIESEL INDEX
The quality of diesel oil is indicated by diesel index number using the following.
Diesel index number = Specific gravity (API) x Aniline in . F
100
Aniline point and specific gravity is noted from API (American Petroleum Institute)
Comparison of gasoline oil and diesel oil
S.No Gasoline oil Diesel oil
1. Low boiling fraction of petroleum
contains C5-C9 hydrocarbons.
High boiling fraction of petroleum
contains C15-C18 hydrocarbons.
2. Fuel for SI engine Fuel for Cl engine.
3. Knocking tendency is measured in
octane rating
Knocking tendency is measured in cetin
rating.
4. Knocking is due to premature
ignition
Knocking is due to ignition lag.
5. Antiknocking is improved by the Anti knocking is improved by doping
CY6251 ENGINEERING CHEMISTRY II
89
SCE Dept.of S&H
addition of TEL with ethyl nitrate.
6. Its exhaust gases contain higher
amount of pollutants
Its exhaust gases contain lesser amount
of pollutants.
7. More consumption, lower thermal
efficiency
Less consumption, higher thermal
efficiency.
5.8. Hydrogenation of coal
The preparation of liquid fuels from solid coal is called Hydrogenation of coal.
Coal contains about 4.5% of hydrogen compared to about 18% of in petroleum. So,
coal is a hydrogen deficient compound.
If coal is heated with hydrogen to high temperature under high pressure, it is converted
to gasoline.
There are two methods available for the hydrogenation of coal.
(a) Bergius process (or direct method)
(b) Fischer- Tropsch Process (or indirect method)
5.8.1(a)Bergiusprocess(indirectmethod)
Finely powdered coal + heavy oil+ catalyst powder (tin or nickel) is made into a paste
The paste is pumped along with hydrogen gas into the converter, where the paste is
heated to 400-450ċ under a pressure of 200-250atm.
During this process hydrogen combine with coal to form saturated higher
hydrocarbons, which undergo further decomposition at higher temperature to yield
mixture of lower hydrocarbons.
The mixture is led to a condenser, where the crude oil is obtained.
The crude oil is then fractionated to yield.
(i) Gasoline (ii) Middle oil (iii) heavy oil
The middle oil is further hydrogenated in vapour phase to yield more gasoline.
The heavy oil is recycled for making paste with fresh coal dust.
CY6251 ENGINEERING CHEMISTRY II
90
SCE Dept.of S&H
The yield of gasoline is about 60% of the coal.
5.8.2 (b) Fischer-tropics process (indirect method)
In this process coal is first converted into coke. Then water gas is produced by passing steam
over red hot coke
C + H2O 1200ċ CO + H2
(Water gas)
The water gas is mixed with hydrogen and the mixture is purified by passing through
Fe 2O3 +Na2CO 3 (to remove sulphur compounds).
The purified gas is compressed to 5 to 25 atm and then led through a converter, which
is maintained at a temperature of 200-300⁰C.
The converter is provided with a catalyst bed consisting of a mixture of 100 parts
cobalt, 5 parts thoria, 8 parts magnesia and 200 parts kieselgurh earth.
A mixture of saturated and unsaturated hydrocarbon is produced as a result
polymerization.
n CO+2nH2 CnH2n + nH2O
n CO+(2n+1)H2 CnH2n +2+ nH2O
The out coming gaseous mixture is led to condenser, where the liquid crude oil is
obtained.
The crude oil is fractionated to yield (i) Gasoline and (ii) Heavy oil.
The heavy oil is used for cracking to get more gasoline.
5.9 GASEOUS FUELS
ADVANTAGES OF GASEOUS FUELS:
Gaseous fuels have high calorific value than solid fuels.
During burning they do not produce any ash or smoke.
Compared to solid and liquid fuels, they have high thermal efficiency.
CY6251 ENGINEERING CHEMISTRY II
91
SCE Dept.of S&H
They can be easily transported through the pipes.
DISADVANTAGES OF GASEOUS FUELS:
They are highly inflammable and hence the chances for fire hazards are high.
Since gases occupy a large volume, they require large storage tanks.
5.9.1. COMPRESSED NATURAL GAS (CNG)
When the natural gas is compressed, it is called compresses natural gas (CNG).
The primary component present in CNG is methane. It is mainly derived from natural gas.
Properties
1. CNG is the cheapest, cleanest and least environmentally vehicle impacting
alternative fuel.
2. Vehicles powered by CNG produce less carbon monoxide and hydrocarbon (HC)
emission.
3. It is less expensive than and diesel.
4. The ignition temperature of CNG is about 55ċ.
5. CNG requires more air for ignition.
Uses:
CNG is used to run an automotive vehicle just like LPG.
Comparison of emission levels between CNG- driven vehicles and petrol driven vehicles
Pollutants
Emission Levels
Petrol Driven Vehicle CNG Driven Vehicle
CO (gm/km) 0.92 0.05
HC (gm/km) 0.36 0.24
5.9.2 PRODUCER GAS
It is a mixture of CO&N2 with small amount of H2. Its average composition is as follows.
Constituents Percentage (%)
CO 30
N2 51-56
H2 10-15
CO2+CH4 rest
It is calorific value is about 1300 kcal/m3.
Manufacture
The reactor used for the manufacture of producer gas is known as gas producer.
It consists of a tall steel vessel inside of which is lined with refractory bricks.
It is provided with cup and cone feeder at the top and a side opening for producer
gas exists.
At the bottom, it is provided with an inlet pipe for passing air and steam.
When a mixture of air and steam is passes over a red hot coke maintained at about
1100ċ in a reactor, the producer gas is produced.
CY6251 ENGINEERING CHEMISTRY II
92
SCE Dept.of S&H
1. Ash Zone
This is the lowest zone consists mainly of ash. The incoming air and steam mixture is
preheated in this zone.
2. Combustion or oxidation zone
This is the zone next to ash zone. Both the reactions are exothermic. Hence, the temperature
of the bed reaches around 1,100ċ.
C+1/2O2 CO exothermic
C+O2 CO2 exothermic
3. Reduction Zone
This is the middle zone. Here both CO2 and steam are reduced.
C+CO2 2CO endothermic
C+H2O CO+H2O endothermic
The above reactions are endothermic. Hence the temperature of the coke bed falls to 1000ċ.
4. Distillation or Drying Zone
This is the upper most of the coke bed. In this zone (400-800ċ) the incoming coke is heated
by the outgoing gases.
Uses
1. It is used as a reducing agent in metallurgical operations.
2. It is also used for heating muffle furnaces, open-hearth furnaces etc.
5.9.3. WATER GAS
It is mixture of CO and H2 with small amount of N2. The average composition of water gas
is as follows.
Constituents Percentage
CO 41
H2 51
N2 4
CO2+CH4 rest
Its calorific value is about 2800kcal/m3
CY6251 ENGINEERING CHEMISTRY II
93
SCE Dept.of S&H
Manufacture
The water gas producer consists of a tall steel vessel, lined inside with refractory
bricks.
It is provide with cup and cone feeder at the top and a side opening of water gas
exist.
At the bottom on it is provide with two inlet pipes for passing air and steam.
When steam and little air is passed alternatively over a red hot coke maintained at
about 900-1000ċ in a reactor, water gas is produced.
Step-I
In the first stage, steam is passed through the red hot coke, where CO &H2 are produced.
The reaction is endothermic. Hence, the temperature of the coke bed falls.
C+ H2O CO+H2 endothermic
Step-II
In the second stage, in order to raise the temperature of the coke bed to 1000ċ, the steam
supply is temporarily cut off and air blown in; the reaction is exothermic.
C+O2 CO2 exothermic
Thus the steam-run and air blow are repeated alternatively to maintain proper temperature.
Uses
1. It is used for the production of H2 and in the synthesis of ammonia.
2. It is used to synthesis gasoline in Fischer-Tropics process.
3. It is also used in the manufacture of power alcohol and carbureted water gas (water gas
+ oil gas).
5.9.4 LPG- Liquefied Petroleum gas
It is also known as bottled gas or refinery gas.
It is obtained by a by-product during the fractional distillation of heavy oil or
cracking of higher hydrocarbons.
It can easily be liquefied under pressure, but exist as gas at atmospheric
pressure.
CY6251 ENGINEERING CHEMISTRY II
94
SCE Dept.of S&H
LPG consists of the following hydrocarbons containing carbons atoms up to
4(C4).
The average composition of LPG is
Propane - 24.7%
Butane - 38.5%
Isobutene - 37.7%
LPG has the calorific value of about 2500 Kcals/m3.
Uses
1. LPG is supplied with the trade name like indene bharath gas etc. It is mainly used as
domestic and industrial fuel.
2. It is also used as motor fuel, because it easily mixes with air and burns without any
pollution creating residue.
Advantages
1. It possesses high efficiency and heating rate.
2. Burns completely without smoke.
3. Needs only little care in maintenance.
4. Easily transported using steel cylinder to any places.
5. It is very cheaper than gasoline.
Disadvantages
1. Handling should be only under pressure.
2. User of LPG in engines is possible only if it works under high compression ratio.
3. Its response to blending is poor and so its uses are selective.
ii) Nitrogen Content:
Kjeldahl’s method: Con.H2SO4,
Powdered Coal Ammonium sulphate (clear solution)
K2SO4 Catalyst
Std N/10 HCl NaOH
Reactions :
Neutralisation takes place NH3
2N + 3H2+H2SO4 (NH4)2SO4
(NH4)2SO4+2NaOH 2 NH3 + Na2SO4 +2 H2O NH3 + HCl
From the volume of HCl consumed % of Nitrogen is calculated
% of N2 in coal = 1.4 x volume of acid consumed x Normality
Weight of coal sample
i) Sulphur Content :
Burnt in
CY6251 ENGINEERING CHEMISTRY II
95
SCE Dept.of S&H
A known amount of coal Sulphate
Bomb calorimeter Extracted with water
Extract
BaCl2
Filtered, dried & weighed BaSO4
From the weight of BaSO4, % of Sulphur is calculated
% of Sulphur = 32 x weight of BaSO4 obtained / 233 x weight of coal sample x 100
iv) Ash content :
Moisture & volatile ½ hr
matter removed coal Loss in weight of coal is noted
without lid 700 + 500
c
Loss in weight of the coal
% of volatile matter in coal = x 100
Weight of air-dried coal v) Oxygen
content :
% of Oxygen in coal = 100 - % of ( Carbon + Hydrogen + Sulphur
+ Ash content
S.NO CONTENTS SIGNIFICANCE
1
High Carbon
& Hydrogen
i) Increases calorific value of coal ii) Helps in the
2 High Nitrogen No calorific value
High
Sulphur
i) Increase calorific value ii) It produces SO2 , SO3 and corrosion takes place
4
High
Oxygen
i) Low calorific value ii)
Increases moisture
holding capacity of coal
Draw backs of presence of S in Coal:
1. The combustion products of sulphur, SO2 and SO3 are harmful and have
corrosion effects on equipments
2. The coal containing sulphur is not suitable for the preparation of etallurgical
coke as it affects the properties of the metal.
CY6251 ENGINEERING CHEMISTRY II
96
SCE Dept.of S&H
Description of Orsat's apparatus
It consists of a horizontal tube having three way stop cock at one end. The end of three way stop
cock is connected to a U tube containing fused CaCl2 to remove moisture in the gas. The another end of
the tube is connected with a graduated burette. The burette is surrounded by a water jacket in order to keep
the temperature of gas constantly. The lower end of the burette is connected by a water reservoir by means
of Rubber tube. The level of the water in burette can be raised or loweredby raising or lowering the
reservoir. The middle of the horizontal tube is connected with 3 bulbs(A, B and C) for absorbing flue gases
as follows:
i. Bulb 'A' containing KOH solution and it absorbs only CO2
ii. Bulb 'B' containing alkaline pyrogallol solution and it absorbs only O2
iii. Bulb 'C' containing ammoniacal cuprous chloride solution and it absorbs CO.
Working of Orsat apparatus
The bulbs A, B and C are cleaned and filled by respective solutions. Now, the three way stop cock
is opened and the burette is filled with water, by raising the water reservoir to remove air from the burette.
Then, the flue gas is taken in the burette up to 100 cc by raising and lowering the reservoir. The 3 way stop
cock is now closed.
Absorption of gases in bulbs
i) Absorption of CO2
The stopper of the bulb 'A' is opened and the flue gas is allowed to pass by raising the water
reservoir. CO2 present in flue gas is absorbed by KOH. This process is repeated several times by raising
and lowering the water reservoir until the volume of burette becomes constant. The decrease in volume of
burette indicates the volume of CO2 in 100 cc of the flue gas. Now the stopper of the bulb „A' is closed.
ii) Absorption of O2
The stopper of the bulb 'B' is opened and the flue gas is allowed to pass. O2 present in the flue gas
is absorbed by alkaline pyrogallol. This process is repeated several times until the volume of burette
becomes constant. The decrease in volume of flue gas in burette indicates the volume of O2 . Now the
stopper is closed.
c) Absorption of CO
The stopper of the bulb 'C' is opened and the flue gas is allowed to pass. 'CO' present in the flue gas
is absorbed by ammoniacal cuprous chloride solution. This process is repeated several times until the
volume of burette becomes constant. The decrease in volume of flue gas in burette indicates the volume of
CO. The remaining gas in the burette after the absorption of CO2 , O2 and CO is taken as nitrogen. The %
of N2 = [100 (% of CO2 + % of O2 + % of CO)]
CY6251 ENGINEERING CHEMISTRY II
97
SCE Dept.of S&H
Glossary
Fuel
Fuel is a combustible substance, containing carbon as the main constituent, which on
burning gives large amount of heat that can be used for domestic and industrial purposes.
Calorific value
Is the total quantity of heat liberated when a unit mass of the furel is burnt completely
Calorie
Is the amount of heat required to raise the temperature of one gram of water through one
degree centigrade.
Cracking
Is defined as “ the decomposition of higher boiling hydrocarbons of high molecular weight
into simpler, lower boiling hydrocarbons of lower molecular weight”.
Synthetic petrol
The preparation of liquid fuels from solid coal is called hydrogenation of coal (or) synthetic
petrol.
Knocking
Is a kind of explosion due to rapid pressure rise occurring in an IC engine.
Octane number
Is defined as “ the percentage of iso-octane present in a mixture of iso-octane and n-
heptanes, which matches the fuel under test in knocking characteristics”.
Cetane number
Is defined as “ the percentage of hexadecane present in a mixture of hexadecane and alpha
methyl naphthalene, which has the same ignition characteristics as the diesel under test”.
Water gas
Is a mixture of combustible gases (CO and H2) with small amount of non combustible gases
(CO2, N2).
Producer gas
Is a mixture of combustible gases ( CO & N2 ) with small amount of non-combustible gases
( N2, CO2 etc).
Power alcohol
Is known as power alcohol. It is used as additive to motors fuels, when blended with petrol
at concentration of 5-10%, it is called power alcohol.
CY6251 ENGINEERING CHEMISTRY II
98
SCE Dept.of S&H
Unit – I, WATER TECHNOLOGY
01. Define boiler feed water. The water fed into the boiler for the production of steam is known as boiler feed water.
02. What are the requirements of boiler feed water?
It should free from
(i). Suspended solids. (ii). Dissolved salts like MgCl2
(iii). Hardness. (iv). Alkalinity. (v). Dissolved gases like O2 and CO2
03. What are the disadvantages using hard water in boiler?
1. Scale and sludge formation. 2. Caustic Embrittlement.
3. Priming and Foaming. 4. Boiler corrosion.
04. What are the disadvantages formation of deposits in steam boilers and heat exchangers?
1. Wastage of fuels. 2. Decrease in efficiency. 3. Boiler explosion.
05. Define Boiler explosion.
When thick scales crack due to uneven expansion, the water comes suddenly in contact with
over-heated iron plates. This causes in formation of a large amount of steam suddenly. So sudden high-
pressure is developed, which may even cause explosion of the boiler.
06. What are the methods used to be prevention of scale formation?
Prevention of scales formation: (i). External Treatment – zeolite process
(ii). Internal Treatment.- carbonate conditioning. 07. What are the methods used to be softening hard water?
(i). External Treatment – zeolite process, Demineralisation process
(ii). Internal Treatment.- carbonate conditioning, calgon conditioning.
08. What is meant by internal conditioning of water? Give one example.
Treating the boiler water in the boiler itself by adding chemicals to remove scale forming
substance is called internal conditioning.
Ex: carbonate conditioning, phosphate conditioning, calgon conditioning.
09. What is meant by external conditioning of water? Give one example.
Treating the boiler water before feeding it into boiler is called external conditioning.
Ex: zeolite process, Demineralisation process
10. Distinguish between internal contioning and external conditioning methods.
Internal contioning External conditioning
CY6251 ENGINEERING CHEMISTRY II
99
SCE Dept.of S&H
To remove hardness producing salts, chemicals were added to the boiler water in
the boiler itself and that treatment is
known as internal conditioning.
Treating the boiler water before feeding it into boiler is called external
contioning.
11. What is meant by caustic embrittlement? How is it prevented?
Caustic embrittlement means intercrystalline cracking of boiler metal. It is prevented by
using softening agent like sodium phosphate and by adding tannin and lignin.
12. What is desalination?
The process of removing common salt (NaCl) from the water is known as desalination. The
water contains dissolved salts with brackish taste is called brackish water.
Desalination = Removal of common salt (NaCl ) from water
13. What are boiler compounds? Mention two different boiler compounds and their
actions.
The chemicals directly added into the boiler for removing scale forming
substances is known as boiler compounds. Ex: Sodium carbonate and Sodium
phosphate
14. What is Calgon? How does it function in water treatment?
Calgon – Sodium Hexa Meta Phosphate
It interacts with calcium ions forming a highly soluble complex and thus prevents
the precipitation of scale forming salt.
15. What is Reverse osmosis?
When two solutions of different concentrations are separated by a semipermeable
membrane, when a pressure is applied on the concentrated side, the solvent flow from higher
concentration to lower concentration.
16. What are the advantages of reverse osmosis method?
i. Low capital cost, easy operating.
ii. RO method is used for converting sea water into drinking
water.
iii. It removes all types of impurities like non-ionic and
colloidal.
iv. The life time of membrane is high and it can be replaced within few minutes.
CY6251 ENGINEERING CHEMISTRY II
100
SCE Dept.of S&H
Unit – I Water Technology.
16 Marks Questions.
01. Define Boiler Feed Water. What are the requirements of Boiler Feed Water?
Boiler Feed Water: The water fed into boiler for the production of steam is called boiler
feed water.
It should be free from turbidity, oil, dissolved gases, alkali and hardness
producing substances.
Requirements of Boiler Feed Water:
i). It should has zero hardness.
If hardness present in boiler feed water, it produces scales and sludges, which prevents
efficient heat transfer.
ii). It must free from dissolved gases like O2 and CO2.
If dissolved gases present in boiler feed water, it leads to boiler corrosion.
iii). It should be free from suspended impurities.
If it is present in boiler feed water, it produces wet steam.
iv). It should be free from dissolved salts and alkalinity.
If it is present in boiler feed water, it produces caustic embrittlement, which causes
brittlement of boiler parts.
02. What is Zeolite? How is water softened by zeolite? Give equations.
Zeolite:Sodium Aluminum Orthosilicate.
Na2O.Al2O3.xSiO2YH2O.
The synthetic form of zeolite is known as
PERMUTIT, which is porous and possess gel
structure and Ze stands for insoluble zeolite.
Principle: The sodium ions which are loosely
held in Na2Ze are replaced by Ca2+
and Mg2+
ions present in water.
Process: When hard water is passed through a bed of
zeolite placed in a closed cylinder, the hardness
CY6251 ENGINEERING CHEMISTRY II
101
SCE Dept.of S&H
causing ions like Ca2+
and Mg2+
ions are taken
up by zeolite. Sodium salts are released during the
reaction as byproduct.
For softening of water by zeolite process, hard water is percolated at a specified rate
through a bed of zeolite, kept in a cylinder.
The hardness causing ions like Ca2+
and Mg2+
are retained by the zeolite as CaZe and
MgZe. While the outgoing water contains sodium salts.
The various reactions taking place may be
Na2Ze + Ca(HCO)2 CaZe + 2NaHCO3
Na2Ze + Mg(HCO)2 MgZe + 2NaHCO3
Na2Ze + MgCl2 MgZe + 2NaCl
Na2Ze + CaCl2 CaZe + 2NaCl
Na2Ze + CaSO4 CaZe + Na 2SO4
Na2Ze + MgSO4 MgZe + Na 2SO4
Regeration
After some time zeolite gets exhausted. The
exhausted zeolite is again regerated by treating
with 10%solution of NaCl.
CaZe + 2 NaCl → Na2Ze + CaCl2
MgZe + 2 NaCl → Na2Ze +MgCl2
Advantages: (i). Output water has only 1-2 ppm. (ii).
Operation is easy.
(iii). No sludge is formed during the process.
03. Explain formation of deposits in steam boilers and heat exchangers. Steamboilers: Sealed vessel where water is converted to steam.
A steam boiler is a type of generator that is used to create steam. Heat exchangers: A device for transferring heat from one medium to another.
Heat exchangers are designed to remove excess heat from aircraft engines,
optics, x-ray tubes, lasers, power supplies, military equipment, and many
other types of equipment that require cooling beyond what air-cooled heat
sinks can provide.
CY6251 ENGINEERING CHEMISTRY II
102
SCE Dept.of S&H
Formation of deposits: Scale and sludge formation. Scale:If the precipitate forms hard and adherent coating on the inner walls of the boiler is known
as scale. It is formed by the substances like CaSO4, Mg(OH)2 and Ca(HCO3)2.
Scales are difficult to remove even with the help of hammer and chisel. Scales are the main
sources of boiler troubles. Formation
of scales may be due to
(i). Decomposition of calcium bicarbonate.
(ii). Deposition of calcium sulphate.
(iii). Hydrolysis of magnesium salts.
(iv). Presence of silica. Sludge: In boiler, water contains the precipitate loose and slimy is known as sludge. It is
formed by the substances like CaCl2, MgCl2, MgSO4 and MgCO3. Disadvantages:
(i). Poor conductor of heat.
(ii). Excessive sludge formation disturbs the working of the boiler.
(iii). It forms along with scales, then former gets entrapped in the latter and both get
deposited scales.
Prevention of sludge formation: (i).
By using well softened water.
(ii). By frequently below down opearation.
04. What are the disadvantages in scale formation? Explain in detail.(Or)
What are the disadvantages formation of deposits in steam boilers and heat
exchangers?(or)
Write short notes on (i). Wastage of fuels. (ii). Decrease in efficiency. (iii). Boiler
Explosion.
CY6251 ENGINEERING CHEMISTRY II
103
SCE Dept.of S&H
Disadvantages: (i). Wastage of fuels.
(ii). Decrease in
efficiency. (iii). Boiler
Explosion.
(i). Wastage of fuels:
(ii). Decrease in efficiency:
Scales may sometimes deposit in the valves and condensers of the boiler and choke then
partially. This results in decrease in efficiency of the boiler. (iii). Boiler Explosion:
When thick scales crack due to uneven expansion, the water comes suddenly in contact with
over-heated iron plates. This causes in formation of a large amount of steam suddenly. So sudden
high-pressure is developed, which may even cause explosion of the boiler. 05. What are the disadvantages using hard water in boilers?
Disadvantages: 1. Scale and sludge formation. [see Q.No: 3]
2. Priming and Foaming. [see Q.No: 10]
3. Caustic Embrittlement. [see Q.No: 7]
4. Boiler Corrosion. [see Q.No: 9]
6. Explain prevention of scales formation. Prevention of scales formation: (i). External Treatment.
(ii). Internal Treatment. (i). External Treatment:Softening of water (i.e) removing hardness- producing constituents of
water. Ex: Zeolite process and Demineralization process.
(ii). Internal Treatment:Sequestration process.
An ion is prohibited to exhibit its original character by complexing or converting it into other
more soluble salt by adding suitable reagent.
CY6251 ENGINEERING CHEMISTRY II
104
SCE Dept.of S&H
An internal treatment – by adding proper chemical to the boiler water either
(a). To precipitate the scale forming impurities in the form of sludge, which can be remove by blow –
down operation (or)
(b). To convert them into compounds, which will stay in dissolved form in water and thus do not cause
any harm Blow down operation: It is partial removal of hard water through top at the bottom of
boiler,
when extent of hardness in the boiler becomes alarmingly high. Internal treatments methods are, generally, followed by blow-down operation , so that
accumulated sludge is removed.
Internal treatment methods are, (i). Colloidal Conditioning (ii).
Phosphate Conditioning (iii).
Carbonate Conditioning (iv).
Calgon Conditioning. 07. Write short notes on Caustic Embrittlement.
Caustic Embrittlement. = Intercrystalline cracking of boiler metal
It is a type of boiler corrosion, caused by using highly alkaline water in the boiler.
In boiler water, it contains a small amount of sodium Carbonate. In high pressure, it
decomposes to give sodium hydroxide.
Na2CO3 + H2O --- 2NaOH + CO2
Then this NaOH reacts with boiler material and it forms sodium Ferrate and this leads to
brittlement of boiler parts like joints, bends etc.,
Fe +2NaOH --- Na2FeO2 + H2
It is prevented by or Avoided by
(i). By using sodium phosphate as softening reagent instead of sodium carbonate. (ii). By
adding Tannin or Lignin to boiler water for blocks hair-cracks.
(iii). By adding sodium sulphate to boiler water also blocks hair-cracks.
08. Explain Internal conditioning methods of softening hard water. To remove hardness producing salts, chemicals were added to the boiler water in the boiler itself and
that treatment is called internal conditioning.
(i). Colloidal Conditioning (ii). Phosphate Conditioning
(iii). Carbonate Conditioning (iv). Calgon Conditioning. (i) Colloidal Conditioning:
In low-pressure boilers, scale formation can be avoided by adding organic substances like
kerosene ,tannin, agar-agar (a gel), etc., which get coated over the scale forming precipitates, thereby
yielding non-sticky and loose deposits, which can easily be removed by pre-determined blow-down
operations.
CY6251 ENGINEERING CHEMISTRY II
105
SCE Dept.of S&H
(ii). Phosphate conditioning:
Three types of phosphates- mono, di and trisodium phosphates are employed in phosphate
conditioning. The advantages of phosphate conditioning over carborate
conditioning are (i). It can be applied to high pressure boilers and
(ii) It can be used for softening/ conditioning acidic, neutral or alkaline water sample. If acidic water is to be conditioned, trisodium phosphate can be used. For neutral and alkaline
water samples disodium phosphate and monosodium phosphate can be used respectively.
(iii) Carbonate conditioning:
In low pressure boilers, calcium ions are converted into soft and loose sludge by adding sodium
carbonate solution. It forms soft CaCO3 which can be removed by blow-down operation.
Calgon conditioning:
Calgon interacts with calcium ions forming a highly soluble complex and it prevents the Calgon=Sodium HexaMeta phospha)6precipitation of scale forming salt. The complex Na2[Na4(PO3)6] is soluble in water and no problem for its sludge disposal.
09. Write short notes on Boiler corrosion / Explain boiler corrosion in detail / Write
short notes on Boiler troubles – Boiler corrosion. Boiler corrosion taken place in boiler in the presence of gases like dissolved oxygen, dissolved
CO2 and dissolved salts.
Dissolved oxygen: It attacks the boiler material at high temperature and causes the
Corrosion.
4Fe +6H2O + 3O2 --- 4Fe(OH)3
It is removed by chemical and mechanical method.
Chemical Method: Sodium sulphite, Hydrazine used to remove dissolved oxygen.
Mechanical Method: To remove by De-aeration method.
Water spraying in a perforated plate-fitted tower, heated from sides and
connected to vaccum pump. High temperature, low pressure and large exposed
surface reduces the dissolved oxygen in water.
CY6251 ENGINEERING CHEMISTRY II
106
SCE Dept.of S&H
Dissolved CO2: It produces carbonic acid, which is acidic and corrosive in nature
CO2 +H2O --- H2CO3 (Carbonic acid )
It can be removed by adding calculated amount of NH4OH into water and
also removed by de-aeration method.
Dissolved salts(MgCl2): Salts like CaCl2 and MgCl2 undergoes hydrolysis at higher
temperature , to give HCl , which corrodes the boiler
MgCl2 + 2H2O --- Mg(OH)2 +2HCl
Fe +2HCl --- FeCl2 + H2
FeCl2 + 2H2O ---- Fe(OH)2 +2HCl
It can be avoided by adding alkali into the boiler water.
10. Explain priming and foaming (carry over). 1.Priming: It is the process of production of wet steam.
Wet steam – Steam contains droplets of liquid water
It is caused by
i) High steam velocity
ii) Very high level water in the boiler
iii) Sudden boiling of water
iv).Very poor boiler design.
Prevention: It is controlled by
1) Controlling the velocity of steam
2) Keeping the water level lower
3) Good boiler design
CY6251 ENGINEERING CHEMISTRY II
107
SCE Dept.of S&H
4) Using treated water 2) Foaming:
The formation of stable bubbles above the surface of water is called foaming
These bubbles are carried over by steam leading to excessive priming.
It is caused by
i) Presence of oil and grease
ii) Presence of finely divided particles.
It can be prevented by
i). Adding coagulants like sodium aluminate
ii).Adding anti-foaming agents like synthetic polyamides.
11. What is Desalination? Describe desalination of by Reverse Osmosis method with neat
diagram.(or)Explain the reverse osmosis process for desalination of brackish water in detail.
Desalination = Removal of common salt-NaCl from water.
Brackish water = Water containing dissolved salts with a peculiar salty taste. Ex: Sea water
Reverse
Osmosis(R
O):
When a pressure greater than osmotic pressure applied on the concentrated side, the
solvent flow takes place from higher concentration to lower concentration is known
as reverse osmosis.
1) In this RO process, Pure water is separated from salt water.
2) This RO process is also known as Super filtration or Hyper filtration
3) When the pressure is applied from the higher concentration side, the solvent flow
takes place to lower side and these two concentrations are separated by
semipermeable membrane, the salt water is converted into pure water.
4) The membranes used as cellulose acetate, polyamide and some polymers.
Advantages &
RO method:
1. Low capital cost, easy operating.
2. It is used for converting sea water into drinking water
3. It removes all types of impurities like non-ionic and colloidal
. 4. The life time of membrane is high and it can be replaced within few
minutes.
12 . Describe Demineralisation process.
CY6251 ENGINEERING CHEMISTRY II
108
SCE Dept.of S&H
Unit – II electrochemistry & corrosion.
01. Define an Electrochemical cell. Give one example. A cell which converts chemical energy into electrical energy is known as electrochemical cell. Example:
Daniel cell , Batteries.
02. What do you mean by redox reaction? Both reduction and oxidation takes place simultaneously in a cell reaction then it is known as redox
reaction of an electrochemical cell.
03. What is electrode potential? It is the measure of tendency of a metallic electrode to lose or gain electrons, when it is in contact with its
own salt solution. It is denoted as “E”
04. Define an origin of electrode potential. When a metallic electrode is placed in its own salt solution, two types of reaction takes place.
1. +ve ions may pass into the solution. M → Mn+ + ne- (oxidation)
2. +ve ions from the solution may deposit over the metal. Mn+ + ne-→M (reduction)
The above reaction takes place in an electrode then it is known as an origin of electrode potential.
05. Define oxidation potential and reduction potential. Oxidation potential: The tendency of a metallic electrode to lose electrons, Reduction potential: The
tendency of a metallic electrode to gain electrons
06. How an electrochemical is measured? Define EMF of an electrochemical cell. It is measured by EMF.: “The difference of potential which causes flow of electrons from one
electrode of higher potential to the other electrode of lower electrode potential”.EMF= ER-EL
07. What are the applications of electrochemical cell? Determination of sparingly soluble salt.,Determination of the valency ion.
Determination of standard free energy change and K.
Potentiometric titrations can be carried out.,Hydrolysis constant can be determined.
08. Define electrochemical series. When various types of metallic electrodes are arranged in their increasing order of standard reduction
potential on the basis of hydrogen scale is known as emf series.
09. Write the significance of electrochemical series. To calculate the standard emf of the cell.,Relative ease of oxidation or reduction.
Displacement of one element by the other., Hydrogen displacement behavior.
Determination of equilibrium constant (K) for the reaction.
10. Write the mathematical form of Nernst equation and give one application. E = Eo + 0.0591/n log [Mn+]
Application: 1.It is used to calculate electrode potential of unknown metal.
2. Corrosion tendency of metals can be predicted.3. Applications of emf series.
11. Define corrosion. The gradual destruction of the metal or an alloy surface by the chemical or electrochemical reaction with
its environment. (i.e) metal into metal oxide.
12. What are the types of corrosion?
(i). Chemical corrosion. (ii). Electrochemical corrosion 13. What are the factors which affect
corrosion?
(i).Air and moisture. (ii). Electrolytes in water.(iii). Presence of impurities in metal.
(iv). Presence of gases like CO2 and SO2 (v). Differential aeration.
14. Define chemical corrosion. What are the types of chemical corrosion?
It is known as dry corrosion. It is due to the local attack of metal surfaces by the atmospheric
gases like oxygen,H2S,SO2 , N2, etc.
CY6251 ENGINEERING CHEMISTRY II
109
SCE Dept.of S&H
3 types. (i). Oxidation Corrosion. (ii). Corrosion by other gases. (iii). Liquid-metal corrosion.
15. Define an Electrochemical corrosion. What are the types of Electrochemical corrosion?
It occurs due to the existence of separate “anodic” and “cathodic” areas between which current
flows through the conducting solution. At anodic area oxidation occurs and anodic part of metal is
destroyed. (i). Galvanic corrosion. (ii). Concentration cell / Differential aeration corrosion.
16. What are the differences between chemical and electrochemical corrosion?
Chemical corrosion Electrochemical corrosion
1) It occurs dry state Wet state (i.e) presence in moisture
2) Local attack to metal by environment Large number of cathodic and anodic areas
3) Chemical corrosion is self-controlled It is continuous process
4) It follows adsorption mechanism It follows electrochemical reaction
5) Ex: formation of mild scale on iron surface Ex: rusting of iron in moisture
17.What isBedworth rule?
The ratio of the volume of the oxide formed to the volume of the metal consumed is pilling
bedworth rule
18.Bolt and Nut made of the same metal is preferred in practice . Why?
Because such a combination will not permit galvanic corrosion to take place.
19.What are the methods used to control the corrosion?
1. Sacrificial anodic method 2.Impressed current cathodic metho
20 What is paint?
Paint is a mechanical dispersion of one or more finely divided pigments in a medium (thinner +
vehicle) .When paint is applied to a metal surface, the thinner evaporates, while the vehicle undergoes
slow oxidation forming a pigmented film.
21.Differenciate Electroplating and Electro less plating
Electroplating Electroless plating
It is carried out by passing current Used reducing agent
Separate anode is employed Catalytic surface of the substrate acts as an
anode
Anodic reaction is
M → Mn+
+ ne-
Anodic reaction is
R → 0 + ne-
Thickness of the plating is 1-100μm It has a thickness of 1-100μm
22. Define Electro plating and Electroless plating
Electro plating:
It‟s a process in which the coating metal is deposited on the base metal by passing a direct
current through an electrolytic solution containing the soluble salt of the coating metal.
Electro less plating:
It is a technique of depositing of a noble metal from its salt solution on a catalytically active
surface of a base metal by using a suitable reducing agent.
CY6251 ENGINEERING CHEMISTRY II
110
SCE Dept.of S&H
UNIT II
ELECTROCHEMISTRY AND CORROSION
16 MARKS
01. What is electrochemical cell? Explain with example of Daniel cell.
Electrochemical cell: Cells in which the e-s transferred due to redox reaction and
converted into electrical energy.
Example : Daniel cell.
Daniel cell consists of two electrodes like Zn and Cu.
Zinc electrode is dipped in 1M ZnSO4 solution and Cu electrode dipped in 1M
CuSO4 solution.
The two solutions are inter connected by a salt bridge and two electrodes are
connected by a wire through the volt meter.
Each electrode is known as half-cell.
The e-s liberates from Zn electrode flow through the external wire and is consumed by
copper ions at the cathode.
Salt Bridge: U- tube containing saturated solution of KCl in agar-agar gel. It
connects two half cells.
Function of salt bridge: It eliminates liquid junction potential and electrical
continuity between two half cells.
02. How electrochemical cell is measured by potentiometrically? Or
What is emf? How emf is measured by pogendroff’s method?
CY6251 ENGINEERING CHEMISTRY II
112
SCE Dept.of S&H
03. What are electrochemical series? Give its applications.
Electrochemical series: An arrangement in which the standard electrode reduction potential
of different metals are arranged in increasing order on the basis of
hydrogen scale is known as emf series.
Applications of EMF series: (i). To calculate the std. emf of a cell.
(ii). Relative ease of oxidation or reduction.
(iii). Displacement of one element by other.
(iv). To determine K of a reaction.
(v). Hydrogen displacement from acid solutions.
(vi). Predicting spontaneity of redox reations.
(i). To calculate the std. emf of a cell.
The emf of a cell is calculated as follows, Ecell = ER-EL
(ii). Relative ease of oxidation or reduction.
+ve value – higher reduction potential – high reduction. F-
=
2.87, higher reduction – get oxidized
Li+
= -3.07, lower reduction – high oxidation.
(iii). Displacement of one element by other.
Metals which lie higher in the series can displace those elements which lie below them in
the series. Cu can easily displaced by Zn
(iv). Determination of Equilibrium Constant K of a reaction.
From the value of Eo, we can be determined the equilibrium constant K (v)
Hydrogen displacement Behavior
Metals with above H2 scale will displace the hydrogen from an acid solution (ie)-ve
reduction potential. Zinc reacts with hydrogen but not in Ag. Why?
Because it has positive reduction potential
(vi) Predicting Spontaneity of Redox Reactions:
Eo
value is positive=Reaction is Spontaneous
Eo
value is –ve =Non-Spontaneous Process.
04. Derive Nernst equation.
CY6251 ENGINEERING CHEMISTRY II
113
SCE Dept.of S&H
Applications:
(i) To calculate electrode potential of unknown metal
(ii) Application of emf series
(iii) Corrosion tendency of methods can be predicted
CY6251 ENGINEERING CHEMISTRY II
115
SCE Dept.of S&H
What is Chemical corrosion? Explain with its types.
It is classified into 3 types. i). Oxidation corrosion.
ii).Corrosion by the other gases – Hydrogen
iii).Liquid – Metal corrosion
01. Oxidation corrosion
Oxygen present in atmosphere attacks metal surface resulting in the formation of metallic
oxide which is a corrosion product and known as oxidation corrosion.
Oxidation occurs first at the surface of the metal and the resulting metal oxide scale forms a
barrier that tends to restrict either further oxidation. For oxidation to continue either the metal must
diffuse outwards through the scale to the surface or the oxygen must diffuse inwards through the scale,
to the underlying metal.
Both transfer occurs, but the outward metal diffusion is generally, much more rapid than
the inward diffusion of oxygen. Since the metal ion is appreciably smaller than the oxygen ion
and consequently of much higher mobility.
02. PILLING – BEDWORTH RULE:
The ratio of the volume of the oxide formed to the volume of the metal consumed is pilling bed
worth rule.
03. Corrosion by other gases – Hydrogen.
i) At ordinary Temperature : Hydrogen Embrittlement.
The process of formation of cracks and blisters on the metal surface, due to high
pressure of hydrogen gas is called hydrogen embrittlement
(i) Metal direct contact with H2s and forms atomic hydrogen
(ii) Atomic hydrogen diffuses readily into metal to form molecular hydrogen
2) At high temperature – Decarburization
The process of decrease in carbon content in steel is termed as decarburization of
steel.
04) Liquid – metal corrosion
This is due to the chemical action of following liquid metal at high temperature. The
corrosion reaction involves
(i) Either dissolution of a solid metal by a liquid metal.
CY6251 ENGINEERING CHEMISTRY II
116
SCE Dept.of S&H
(ii) Liquid metal may penetrate into the solid metal.
06. Explain Electrochemical corrosion with its types.
01. Galvanic corrosion:
The corrosion occurs when two different metals are in contact with each other in
presence of an aqueous electrolyte solution or moisture is known as Galvanic corrosion.
The more active metal acts an anode the less active and metal acts as a cathode
In Zn-Fe bimetallic couple, Zn undergoes to
corrosion, because compare with Fe, it has
higher –Ve emf Value. So it acts as
an anode. Iron acts as cathode and it is
protected.
Prevention of Galvanic corrosion:
But in the case of Fe – copper bimetallic
couple Fe dissolves and copper is protected.
(ie) Fe acts an anode and copper as a
cathode.
To prevent Galvanic corrosion, the bolt and but are made by same metal. If they are n‟t
corrosion will take place easily.
It may be minimized by putting an insulating material between the two metals.
02. Differential aeration corrosion:- Otherwise it is known as concentration cell corrosion.
It is due to the formation of concentration cell formed by the variation of concentration mainly of
oxygen or any electrolyte on the surface of the base metal.
i).When a metal is partially immersed in a solution,
the metal inside the solution has very poor aeration
compared with the metal that is outside the solution.
ii).The difference in the air concentration of the base
metal can produce the anode with less aerated area and
cathode.
iii).Corrosion will take place at the anode area where the
metal is converted into metal ion. Example: A zinc metal
partially dipped in a brackish solution.
Example: Pitting Corrosion - The holes are formed at corrosion in concentrated places.
Low oxygen part= anode , More oxygen part=cathode.
It is a localized attack, resulting in the formation of a hole around which the metal is relatively
unattached. Ex: metal area covered by a drop of water, sand, dust, etc.
CY6251 ENGINEERING CHEMISTRY II
117
SCE Dept.of S&H
07. Distinguish between Chemical corrosion and Electrochemical corrosion.
Chemical corrosion Electrochemical corrosion
1) It occurs dry state Wet state (i.e) presence in moisture
2) Local attack to metal by environment Large number of cathodic and anodic areas
3) Homogeneous metal surface gets
corroded
Heterogeneous surface
(i.e) Bimetallic contact.
4) Corrosion products accumulate in the
same place, where corrosion occurs
Corrosion occurs at the anode, while the
products formed else where
5) Chemical corrosion is self-controlled It is continuous process
6) It follows adsorption mechanism It follows electrochemical reaction
7) Ex: formation of mild scale on iron surface Ex: rusting of iron in moisture
8) 3 types. i). Oxidation corrosion
ii). Corrosion by other gases- H2
iii). Liquid – Metal corrosion.
2 types.
i). Galvanic corrosion.
ii). Differential aeration corrosion.
08. What are the factors influencing corrosion?
The rate of corrosion is mainly depends on i)
Nature of the metal
ii) Nature of the environment
i). Nature of the metal
a). Position in emf series: Metals above hydrogen in emf series, corroded easily.
Metals have high –ve reduction potential undergoes corrosion.
b) Relative areas of the anode and cathode: Rate of the corrosion has higher % in anodic area, the
rate of corrosion will be more, when the cathodic area is larger.
c) Purity of the metal: The 100% pure will not undergo any type of corrosion. If
impurity present in higher percentage, corrosion takes places at anode.
d) Over voltage: Corrosive environment is inversely proportional to corrosion rate. e)
Nature of the surface film: It is known as pilling- bed worth rule.
f) Nature of the corrosion product: Corrosion is faster when the corrosion product is soluble in
corroding medium. If the corrosion product is volatile, the corrosion rate will be faster.
ii). Nature of the environment:
i). Temperature: Rate of corrosion α temperature.
The rate of corrosion increase with temperature
ii). Humidity: If the humidity is high in the environment, corrosion will be more.
iii). Presence of corrosive gases: The acidic gases like CO2,SO2,H2S are produce electrolytes, which
are acidic and increases the electrochemical corrosion.
iv). Presence of suspended particles: Particles like NaCl present in the moisture and acts a
powerful electrolyte and then enhance the electrochemical corrosion.
v). Effect of pH; the rate of corrosion will be maximum when the corrosive environment is acidic
(ie) PH<7.
CY6251 ENGINEERING CHEMISTRY II
118
SCE Dept.of S&H
09. Explain the Sacrificial anode and impressed current techniques for the preventions of
corrosion.
i) Sacrificial anode method:
i). The application of sacrificial anodes in cathodic protection is based on the differences in
electrochemical reactivity of metals.
ii). In this method, the metal to be protected from corrosion is connected to more active metal which
acts as an anode.
iii). In a redox reaction involving iron and zinc, the zinc will serve as the anode, and iron the
cathode.
iv). The zinc anode will oxidize and provide electrons for the reduction of Fe2+
to elemental iron.
v). This is called cathodic protection. The zinc anode is termed a sacrificial anode.
vi). Iron pipes buried in the ground, and designed to carry water, would normally be expected to rust
pretty quickly.
vii).If they are buried along with a piece of zinc, and connected by a wire the zinc will provide
cathodic protection.
2. Corrosion control through Impressed current method:
An alternative method of providing the current to protect a system is to use some sort of
external power supply. As with the sacrificial system , the structure to be protected is made the
cathode, the difference being that the driving force. Behind the current is not the difference in
potential between the anode and cathode of the system but from the power supply.
Both these types of cathodic protection may be applied to buried pipelines and to steel hulled
ships. For oil drilling platforms, however the method employed is sacrificial in the vast majority of
cases in the north sea.
This technique is useful for protecting large structures like water tanks, underground oil collers,
laid up ships,etc.
CY6251 ENGINEERING CHEMISTRY II
119
SCE Dept.of S&H
10. What is paint? What are the constituents and their functions in paint?
Paint: paint is a mechanical dispersion of one or more finely divided pigments in a medium (thinner +
vehicle) . When paint is applied to a metal surface, the thinner evaporates, while the vehicle undergoes
slow oxidation forming a pigmented film.
Constituents:
1. Pigments. 2. Vehicle or drying oil. 3. Thinner. 4. Drier. 5. Filler or extender. 6. Plasticizer
7. Antiskinnig agent.
i) Pigments: They are colour producing substances in paint.
Ex: white colour- white lead, black=- carben black red-indian red, green –
chromium oxide.
Function: i). It gives colour and opacity to the film.
ii). It also provides strength to the film.
iii). It provides weather resistance of the film.
ii) Vehicle (or) drying oil: This is a non-volatile portion of a medium and film forming
constituent of the paint. These are high molecular weight fatty acids present in vegetable and animal
oils. Ex: Linseed oil, castor oil.
Function:
i) They form a protective film by the oxidation and polymerization of the oil ii)
They hold the pigment particles together on the metal surface
iii) They impart water repellency , toughness and durability to the film.
iii) Thinners or solvents: Thinner is a volatile substance present in the medium.
Ex: turpentine, toluol, xylol etc.
Function:
I) It increases the elasticity of the film
II) It helps easy drying of the paint film
III) It increases the penetrating power of the vehicle.
iv) Extenders or fillers: These are colourless (white) pigments which improve the quality of the paint.
Ex: Gypsum, Jal ,china clay, silica, etc.
Functions:
i) It reduces the cost of paint
ii) It prevents the cracking and shrinkage of the film iii)
It modifies the shades of the pigments
v).Driers: these are the substances, used to accelerate the process of crying.
Ex: metallic soaps.
Functions: i).They are oxygen –carriers (or) catalists.
ii). They provide oxygen , which is essential for oxidation, polymerization of drying oil.
vi).Plasticisers: these are chemicals added to the paint to provide elasticity to the film and to prevent
cracking of the film. Ex: triphenyl phosphate, tricresyl phosphate, etc.
vii). Antiskinning agents: These are chemicals added to the paint to prevent gelling and
skinning of the paint. Ex: polyhydhroxy phenol.
11. Explain the electroplating of Gold.
Electroplating: It‟s a process in which the coating metal is deposited on the base metal by passing a
CY6251 ENGINEERING CHEMISTRY II
120
SCE Dept.of S&H
direct current through an electrolytic solution containing the soluble salt of the coating metal.
Ex: Electroplating of Au (gold) over copper object.
The copper object to be plated is first treated with dilute acid.
Then this copper object and gold rod are immersed in an electrolyte.
Copper object acts cathode and gold rod is an anode.
These electrodes are connected with direct power supply.
When current is passed from battery through the solution, gold dissolves in electrolyte and
deposits uniformly in copper object.
12. Explain the Electroless plating of Nickel.
Metal ions + Reducing Agent Metal (Deposited) + Oxidised Product
Definition: it is a technique of depositing of a noble metal from its salt solution on a
catalytically active surface of a base metal by using a suitable reducing agent.
Electroless Nickel plating:
Step 1: Pretreatment and activation of the surface:
The surface to be plated is first degreased by using organic solvents or alkali followed by acid
treatment.
CY6251 ENGINEERING CHEMISTRY II
121
SCE Dept.of S&H
Step 2: preparation of plating bath composition:
Coating solution NiCl2.6H2O 30 g/l
Reducing agent NaH2PO2H2O
(sodium hypophosphite)
10 g/l
Complexing agent Sodium succinate 10 g/l
Buffer Sodium acetate 10 g/l
Temp 85-95
oc
pH 4-6
The pretreated object is immersed in the plating bath for the required time during which the
following reduction reaction will occur and the Ni gets coated over the object.
UNIT – III ENERGY SOURCES
2 MARKS QUESTION BANK
1. What is nuclear energy?
The energy released by the nuclear fission reaction is called nuclear energy. 2. What is nuclear fission reaction?
The process of splitting of heavy nucleus into two or smaller nuclei with
Simultaneous liberation of large amount of energy in the form of heat is known as nuclear fission
reaction.
92U235
+ 0n1→ 56Ba
140+ 36Kr
93+30n
1
3. What is nuclear fusion reaction? Give one example.
The process of combination of two or more lighter nuclei into heavier nuclei,
with simultaneous liberation of large amount of energy is known as nuclear fusion reaction.
Ex: 1H1+ 1H
12H
4+energy
4. Differentiate nuclear fission and fusion reaction.
CY6251 ENGINEERING CHEMISTRY II
122
SCE Dept.of S&H
Nuclear fission Nuclear fusion
It is the process of breaking the heavier nucleus.
It is the process of combination of lighter nuclei.
It emits radioactive rays Does not emit radioactive rays.
Occurs at ordinary temperature At high temperature(>106
K)
Chain reaction takes place No chain reaction.
Emits neutrons Emits positrons
It can be controlled Cannot be controlled
5. Define nuclear chain reaction. It is a nuclear reaction, in which neutrons from a previous step propagate and repeat the reaction.
It takes place only nuclear fission reaction.
6. What are fissile and fertile nucleides?
Fissile – Fissionable materials like U235
Fertile – Non- Fissionable materials like U238
7. What are solar cells? Give one example./What is a photo galvanic cells?
It is a device, Converting solar energy directly into electrical energy.
It provides power supply for space satellites. Ex: solar water heater , photovoltaic cell 8. What is solar energy conversion?
It is the process of conversion of direct sunlight into more useful forms.
It undergoes mainly two types of mechanisms. 1. Thermal conversion. 2. Photo conversion 9. What
are the merits of wind energy?
a) Nonpolluting and sustainable energy source.b).The scope of wind energy is enormous.
c). It is a renewable and sustainable energy source.
d). It is available in many offshore, onshore and remote areas.
10. What are batteries?
It is a device, converted chemical energy into electrical energy. It is an arrangement of
electrochemical cells connected in series,and it can be used as a source of direct electric
current.
11. Define breeder reactor.
Breeder reactor is one which converts non-fissionable material into fissionable material.
Non-fissionable material ------------> fissionable material.
Ex: 92U238
+ 0n1→94Pu
239 + 2 e
-
Non-fissionable fissionable
94Pu239
+ + 0n1
→ fission products + 3 0n1
12. What are non-conventional energy sources? Give two examples.
Non-conventional energy sources are those energy sources which are exposed to use from
modern technological advancements; rather than the normal use of conventional fuels as
energy sources like gas or oil.
Ex: 1. Wind energy 2. Solar energy 3.Tidal energy 4. Hydropower energy
13. What is a fuel cell?
CY6251 ENGINEERING CHEMISTRY II
123
SCE Dept.of S&H
It is a device in which the chemical energy of the fuel hydrogen is directly converted into
electrical energy without combustion.
Fuel + Oxygen → Oxidation products + Electricity.
14. What are the advantages of fuel cell? Or What are the advantages of H2-O2 fuel cell?
It is used as an auxiliary energy source in space vehicles, submarines.
Used in military vehicles. It is a pollution free one.The product is water, so it is a valuable source
of fresh water by the astronauts.
15. What are the applications of lithium batteries?
Used in cell phones, Digital cameras, Watches, Remote cars, Calculators, Toys, Backup
batteries in computers, etc.
16. List any two advantages of lithium batteries.
Its cell voltage is high, 3V. Li is a light-weight metal, only 7g (1 mole) material is required to
produce 1 mole of electrons. It contains solid material so there is no leakage from battery. This
battery can be made in a variety of sizes and shapes.
17. Define alkaline battery.
It is called as a dry cell.>It has the electrolyte of KOH
A zinc cylinder is filled with an electrolyte of Zn,KOH and MnO2
A carbon rod acts as a cathode and zinc body acts as a anode.
18. What are the general components in nuclear reactor?
The components are fuel rods, control rods, moderators, reflectors, coolants and pressure
vessel, Turbine
UNIT – III ENERGY SOURCES
16 MARKS QUESTION BANK
01. Distinguish between Nuclear fission and Nuclear fusion reaction.
Nuclear fission
Nuclear fusion
1. Breaking a heavy nucleus into smaller
Combination of two smaller nuclei.
2. Emits radioactive rays
Does not emit radioactive rays
3. Reaction takes place at ordinary
temperature
At high temperature. > 106K.
4. It gives chain reaction.
No chain reaction
5. Emits neutron
Emits positron
6. It can be controlled
It cannot be controlled.
7. The mass number and atomic number of new
elements are lower than the parent nucleus.
Higher than that of starting elements.
8. Ex: Fission reaction of 92U235
, power
generation in Nuclear Power Plant,
Kalpakkam&koodankulam, Tamilnadu.
Ex: Fission reaction takes place in sun.
CY6251 ENGINEERING CHEMISTRY II
124
SCE Dept.of S&H
2. Define Nuclear fission reaction. Explain with one example in detail.
CY6251 ENGINEERING CHEMISTRY II
125
SCE Dept.of S&H
C
03. Explain Nuclear Reactor-Power Generator with neat diagram./ Light Water Reactor Nuclear Reactor: A device used for power generation, in which a nuclear chain reaction is
initiated, maintained and controlled to produce the heat energy is
known as nuclear reactor
.
Nuclear Energy Converted Thermal Energy
(or)
Heat Energy
onverted Electrical Energy
CY6251 ENGINEERING CHEMISTRY II
126
SCE Dept.of S&H
Components:
1) Fuel Rods: It produces heat energy and neutrons.
Ex: Natural Uranium (99.28% U238
and 0.714 % U235
) and Pu239
2) Control Rods: To keep power production at a steady state.
Ex: Boron and Cadmium rods.
3) Moderators: Function to reduce the kinetic energy of fast fission neutrons to slow
neutron and this is done in a small fraction of a second.
Ex: Graphite, Be, Ordinary water and Heavy water.
4) Coolants: To remove the intense heat produced in the reactor and to bring it out for
utilization. Ex: Ordinary water, Heavy water, liquid metals and gases.
5) Reflector: It placed around the core to reflect back some of the neutrons that leak out
from the surface of the core.
6) Pressure vessel: It enclosed the core and reflector. It also provides the entrance and exit passages
for coolant. (Pressure 200 kg/cm2)
7) Shielding: To attentiate the Gama rays and other radiations coming out from the reactor.
2 Types. (i). Thermal shield (ii). Biological shield.
8) Turbine: The steam at high pressure, generated in the heat exchanger is used to operate a
steam turbine, which derives a generator to produce electricity.
04. Explain Breeder reactor with reactions.
CY6251 ENGINEERING CHEMISTRY II
127
SCE Dept.of S&H
05.
Define solar cell. Explain solar energy conversion in detail. Solar cell = Photogalvanic cell : It is a device used for converting solar energy into
electricity. It is made by interconnecting a large number of photovoltaic cells.
CY6251 ENGINEERING CHEMISTRY II
128
SCE Dept.of S&H
Solar Energy Conversion: It is the process of conversion of direct sunlight into more useful forms.
Conversion may be in two forms. 1. Thermal Conversion. 2. Photo Conversion.
01. Thermal Conversion:
It involves absorption of thermal energy in the form of IR radiation. Temperature below
100oC, is useful for heating purpose of water and refrigeration.
Methods: (i).Solar heat collectors. (ii).Solar water heater.
(i). Solar heat collectors: It consists of natural materials like stones, bricks which can absorb heat
during the day time and release it slowly at night.
Uses: It is used for houses in cold condition. (ii). Solar Water Heater:
It consists of an insulated box inside of which is painted
with black paint. There is a provision for sun light absorption
using a glass lid and store solar heat. Inside the black
painted, copper coil and cold water is flow in and gets
heated and storage in a tank. 02. Photo Conversion: It involves conversion of light energy directly into electrical energy.
Methods: Solar Cell.
Solar Cell: Ex: Solar light, solar pump, solar battery. It is a device, converting solar energy directly into
electrical energy. Principle: When solar rays fall on a two layer of
semi-conductor devices, a potential difference between the two layers is produced. This potential
difference causes flow of electrons and produces electricity. Working: When the solar ray falls on the top layer and the e-s promoted to the conduction into n-type
semiconductor. The potential difference occurs; it should lead current increasing (i.e) flow e-s. They
are connected with an external circuit, and current is generated. Applications of Solar Energy :(i). Used in calculators,Watches, etc. (ii).
Used to drive Vehicles.
(iii). Used in boilers to produce hot water for domestic and Industrial uses.
(iv). Used for lighting purposes. (v). Used as a source power in space crafts and satellites. (vi).
Used for producing hydrogen by hydrolysis of H2O. Demerits of Solar Energy: (i). Huge capital cost.
(ii). Not available during night and cloudy days. (iii). Storage of energy is not possible
CY6251 ENGINEERING CHEMISTRY II
129
SCE Dept.of S&H
06. Write a short note on Wind Energy.
Moving energy is called Wind.Energy recovered from the force of the wind is called wind energy.
The wind energy is harnessed by making use of wind mills.
01.Wind Mills:
The strikes of blowing wind on blades of the
wind mill make it rotating continuously.
The rotational motion of the blade drives a
number of machines like water pump, flour mills and
electric generators. Wind mills are capable of generating about 100 kw
electricity.
02. Wind Farms. It is known as the large number of joining wind mills called wind farm. It produces a large
amount of electricity.The minimum speed required for working of a wind generator is 15 km/hr
03. Other methods: (i). Sky Sail (ii). Ladder
mill. Advantages/ Merits of Wind energy:
i. It does not cause any Air pollution.
ii. It is very cheap and economic.
iii. It is renewable.
Disadvantages of Wind energy:
i. It produces noise.
ii. It produces unwanted sound.
iii. Affects bird‟s life.
iv. Affected to the radio signals.
07. Define Battery. Explain with its types.
Battery:
It is a device, converted chemical energy into electrical energy. It contains
several anodes and cathodes.
It is an arrangement of several electrochemical cells connected in series and it can be
CY6251 ENGINEERING CHEMISTRY II
130
SCE Dept.of S&H
used as a source of direct electric current. (D.C).
TYPES OF BATTERIES:
01. PRIMARY BATTERY
i. It is known as Non-Reversible battery.
ii. Electrode and electrode reactions cannot be reversed by passing an external current. iii.
Reactions take place only once and after use they become dead.
iv. They are not chargeable.
v. Ex: Dry Cell, Mercury Cell, Leclanche‟s cell.
02. SECONDARY BATTERY
i. It is known as Reversible battery.
ii. Electrode and electrode reactions are reversiblewhen an external current is passing iii. It
can be recharged again and again.
iv. Also called as Storage cells or Accumulators. v.
Ex: Lead-Acid Battery, Ni-Cd.
03. FLOW BATTERY
In these cells, the reactants, products and electrolytes and continuously passing through
the cell. Here chemical energy is converted to electrical energy.
Ex: H2-O2 fuel cell.
08. Explain Alkaline Battery with neat diagram and cell reactions.
Anode Zinc body
Cathode Carbon rod / Graphite rod
Electrolyte Powdered KOH, MnO2 in the form of paste.
CY6251 ENGINEERING CHEMISTRY II
131
SCE Dept.of S&H
Alkaline battery consists of electrolyte KOH and a Zinc cylinder filled with powdered Zn, KOH
and MnO2 in the form of paste using starch and water. A carbon rod [Graphite] acts as a cathode
and it is immersed in the electrolyte in the centre of the cell. The outside cylindrical
zinc body acts as an anode. Advantages:
i. Zinc doesn‟t dissolve in a basic medium.
ii. Its life is longer than dry battery because there is no corrosion on Zn. iii. It
maintains its voltage, when the current is drawn from it.
Uses: It is used in calculators and watches.
09. Explain Lead acid storage battery.
Cell Representation: Pb/Pb(SO)4//H2(SO)4(aq)/PbO2/Pb
Anode Lead - Pb
Cathode Lead Oxide PbO2
Electrolyte Sulphuric acid - H2(SO)4
CY6251 ENGINEERING CHEMISTRY II
132
SCE Dept.of S&H
This is also a rechargeable battery.It consists of number of voltaic cells. In each cell, anode is Pb
plate and cathode is PbO2
A known number of lead plates are connected with parallel and a number of PbO2 plates
and also connected in parallel. Various plates are separated by insulators like glass fibre. The total
anodes and cathodes are immersed in dil.H2(SO)4 Solution.
Cell reactions: Discharging.-----------------------------------------------------------------------------------------------
Advantages:
(i). It is made easily. (ii). It produces very high current.
(iii). Effective one at low temperature. (iv). Self- discharging rate is low.
Uses:
(i). Used in automobiles like Car, Bus, Van, Lorry, Bike etc.
(ii). Used in Hospitals, Power stations, Telephone exchanges etc.
10. Explain Nickel – Cadmium battery with cell reactions.
Cell Representation: Cd/Cd(OH)2//KOH(aq)/NiO2/Ni
Anode Cadmium (Cd)
Cathode A metal grid containing a paste of NiO2
Electrolyte KOH
This is also a rechargeable battery. It consists of Cd anode and a metal grid containing a paste of NiO2 acts as a cathode. The
CY6251 ENGINEERING CHEMISTRY II
133
SCE Dept.of S&H
Charging
Discharging Cd(S
)
electrolyte is KOH.
Discharging: When Ni-Cd battery operates, Cd gets oxidation and forms Cd2+
and insoluble
Cd(OH)2 is formed. Its emf value is 1.4 V.
Cell Reaction:
Recharging: When an current is passed opposite direction, the cell reaction is reversed. As a
result, Cd gets deposited on anode and NiO2 on cathode.
Cd(OH)2 Ni(OH)2
Energy
NiO2(S) 2H 2O
CY6251 ENGINEERING CHEMISTRY II
134
SCE Dept.of S&H
Advantages:
(i). It is smaller and lighter.
(ii). It has longer life than lead storage cell.
Uses:
(i). It is used in calculators, Electronic devices.
(ii). Used in transistors, cordless appliances.
11. Explain Lithium batteries in detail.
It is known as solid state battery because the electrolyte is used here at solid state.
Anode Lithium (Li)
Cathode TiS2
Electrolyte Polymer
CY6251 ENGINEERING CHEMISTRY II
135
SCE Dept.of S&H
2
2
2
Anode : Li(S) Li+
+ e-
Cathode: TiS2 (S) + e-
TiS-
Over all Li(S) + TiS2 (S) Li+
+
TiS-
LiTiS2
Discharging:
When the anode is connected to cathode, Li+ ions move from anode to cathode. Anode
is Li and cathode is TiS2 and the electrolyte is solid polymer. The cathode is a material capable of
receiving the Lithium ions and electrons.
Recharging:
LiTiS2 Li+
+ TiS-
It is recharged by applying an external current. Emf of Li cells = 3.0V. Advantages: (i). Itsemf is high 3.0V.
(ii). It is a light weight material only 7g required for produce 1 mole of e-
s.
12. Explain Hydrogen- Oxygen Fuel cell / [H2 – O2] Fuel cell. Fuel Cell: It is a device in which the chemical energy of the fuel hydrogen is
directly converted into electricity without combustion.
Anode Hydrogen
Cathode Oxygen ( oxidizer)
Electrolyte 25% KOH or NaOH
CY6251 ENGINEERING CHEMISTRY II
SCE Dept. of S & H
Two porous electrodes – Made of compressed carbon
containing a catalyst like pt / pd.
It consists of two porous electrodes anode and cathode. In
between two electrodes an electrolytic solution 25% KOH or
NaOH filled.
When H2 is bubbled through the anode compartment,
where it is oxidized. The O2 is bubbled at the cathode
compartment where it is reduced. The emf of the cell = 0.8 to 1.0 V. Merits:
i. High efficiency.
ii. No unwanted noise and less maintenance. iii. No
pollution
iv. No need to change electrode often. Uses:
i. Used in military vehicles and space vehicles. ii. H2 – O2 fuel cell, the product is water, so no need of fuel because fuel is water UNIT – IV ENGINEERING MATERIALS 2 MARKS QUESTION BANK 1. What are abrasives? Abrasives are hard substances used for Grinding, cutting, Shaping, drilling, poslishing andsharpening operations. Ex: Diamond,Talc Property of an Abrasive = Hardness 2. How abrasives are classified? Give example for each. Abrasives are classified into two types. 1. Natural abrasive Ex: Talc,Diamond. 2. Synthetic abrasive Ex: SiC and B4C. 3. What are natural abrasives? Abrasives are obtained from nature is called natural abrasives. Ex: Talc,Diamond,Topaz. 4. What are synthetic abrasives? Abrasives are prepared from man - made and obtained some chemical reactions. Ex: silicon carbide (SiC) 5. What is moh‟s scale of hardness? It is a scale in which common abrasives are arranged in their increasing order of hardness. In this scale, lowest: talc (hardness number is 1) highest: diamond(hardness number is 10) 136
CY6251 ENGINEERING CHEMISTRY II
SCE Dept. of S & H
6. Define Refractories. Refractories are materials that can withstand very high temperature without softening or deformation in shape.Ex: Alumina bricks, Magnesite bricks, Zirconia bricks. 7. How refractories are classified? Give example for each. Refractories are classified into three types. 1. Acidic refractories Ex:Alumina bricks. 2. Basic refractories Ex: Magnesite bricks. 3. Neutral refractories Ex: Zirconia bricks. 8. What are the properties of Refractories? (i). Refractoriness (ii). RUL- Refractoriness Under Load (iii). Porosity (iv). Thermal spalling (v).Dimensional stability. 9. What is RUL? The temperature at which the refractory deforms by 10% is called RUL. i.e The load bearing capacity of a refractory can be measured by RUL Test. 10. Define refractoriness of a refractory. [Jan‟10] It is the ability of a refractory material to withstand very high temperature without softening or deformation under the working conditions. 11. What is meant by thermal spalling with respect to a refractory? [Jun‟10] It is the property of a refractory breaking, cracking or peeling of refractory material under high temperature. It is mainly due to (i).rapid change in temperature. (ii).slag penetration. 12. What is Porosity? It is defined as the ratio of its pore volume to the bulk volume. Porosity = W-D ------- X 100 W-A 13. How SiC is prepared? It is prepared by heating a mixture of 60% sand (i.e) SiO2 and 40% coke with a small amount of saw dust and a little salt in an electric furnace to about 1650oC for 36 hours. SiO2+ 3C SiC + 2CO 14. What do you mean by Portland cement? A paste of cement with water on setting and hardening resembles in colour and hardness to Portland stone, a lime stone quarried in Dorset. It is obtained by heating clay containing material and lime containing material to about 1500oC and mixed with gypsum. 15. What are the properties of Portland cement? Setting and hardening and Heat of Hydration. 16. What do you mean by hardening and setting of cement? Setting: Stiffening of the original plastic mass, due to initial gel formation. Hardening: Development of strength, due to crystallization. 17. Give two examples of special cement. White cement , water proof cement. 18. Name 2 water proofing agents added to make water proof cements? Calcium stearate and Aluminium stearate 19. Give any 2 uses of waterproof cement. Used in the construction bridges and structures under water. 20. Give any 2 uses of white cement. (i). Repairing and joining marble pillars and blocks, manufacture of tiles and mosaic works. (ii). Used in the construction bridges and structures under water. 137
CY6251 ENGINEERING CHEMISTRY II
SCE Dept. of S & H
21. What is glass? It is an amorphous, hard, brittle, transparent or translucent, super cooled liquid obtained by fusing a mixture of a number of silicates. Silicates of Na, Ca, Pb are mostly used. 22. Mention some types of glass. Soft glass , hard glass, laminated glass, glass wool, flint glass , silica glass. 23. How is bullet resistant glass prepared? By pressing together several thin layers of glass with vinyl resin in alternate layers. 24. What is the chemical difference between soft glass and hard glass? Na2O.CaO.6SiO2 and K2O.CaO.6SiO2
UNIT – IV ENGINEERING MATERIALS
16 MARKS QUESTION BANK
01. What are Abrasives? Explain with classification.
Abrasives are hard substances used for Grinding, cutting, Shaping, drilling, poslishing
andsharpening operations.
Ex: Diamond,Talc
04. Explain the properties of refractories.
Properties : Refractoriness, RUL, Dimensional stability, Thermal spalling,
Thermal expansion , porosity.
01. Refractoriness:
1. It is ability of a refractory material to withstand very high temperature without softening or
deformation under the working conditions
2. It is measured by PCE test.
3. PCE= Pyrometric cone equivalent
4. P.C.E number and softening temperature of some refractories are as follows a. Silica
bricks
b. Alumina bricks
c. Magnesite bricks
5. PCE is the number which refer to the softening temperature of a refractory specimen of
standard dimension 38mm height and 19mm triangular base.
Measurement:
1) This measurement is called segarcone test.
2) A test cone is determined by comparing its softening
temperature with softening temps.of a series of standard
pyrometric cones.
3) A test cone is prepared from the sample refactory
then it is placed along with the standard segar cone in an electric furnace and heated at
a rate of 10oC per minute.
4) The temperature at which apex (top) of the cone touches the base is taken as the softening
temperature .the PCE number of the standard cone which behaves identically is taken as
the PCE of the test sample.
138
CY6251 ENGINEERING CHEMISTRY II
SCE Dept. of S & H
2)RUL: Refractoriness Under Load:
The temperature at which the refractory deforms by 10 % is called refractoriness under load.
(i.e).The load bearing capacity of a refractory can be measured by RUL test.
A good refractory should have high RUL value.
RUL TEST:
RUL test is conducted by applying a constant load of 3.5 or 1.75 kg/cm2
to the test refractory
specimen of size base 5 cm2
and height 75 cm and heating in a furnace at a standard rate of 10oC per minute.
03.Porosity: It is defined as the ratio of its por volume to the bulk volume
If porosity of a refractory is lower
i) posseses lower thermal conductivity ii) it
reduces thermal spalling
If porosity of a refactory is high
i). it reduces the strength
ii) .It reduces resistance to abrasion
iii). It reduces the resistance to corrosion
Porosity is used to determine like strength, corrosion and thermal conductivity.
A good refractory should have low porosity.
05. How Alumina, Magnesite and Silicon carbide are manufactured?
Manufacture of Alumina bricks:
Alumina bricks is an example for acidic refractories.
Alumina bricks are prepared from minerals silimanite and kyanite
They are anhydrous aluminosilicate materials Al2O3.SiO2
This mineral is fixed with coal in the ratio 1:1 along with plastic clay as binders.
The raw materials are mixed and moulded into bricks
The bricks are then dried and fired at 1600oc
The final product material contains 63 % alumina and 34% silica approximately.
These are used in steel industries.
Manufacture of Magnesite bricks:
Magnesite bricks are an example for basic refractories
Powdered caleinedmagnoite (Mgo) is mixed with caustic magnesia or iron oxide, as a birder with
water mixed and moulded into bricks.
The bricks are then dried and fired at 1500oC
The final product material containsMgO=85%,CaO=2.5% & SiO2=5.5%
139
CY6251 ENGINEERING CHEMISTRY II
SCE Dept. of S & H
There are used in open hearth furnaces, libing converters and reverberatory furnaces.
Manufacture of Silicon carbide (SiC): CARBORUNDUM
SiC is an example for very hard synthetic abrasive.
It is a mixture of SiO2 and coke.
Its hardness is 9.8 on Moh‟s scale.
It is chemically inert and can withstand high temperature.
Preparation Or Manufacture:
It is prepared by heating a mixture of 60% sand (i.e) SiO2 and 40% coke with a small amount of saw
dust and a little salt in an electric furnace to about 1650oC for 36 hours.
SiO2
+ 3C SiC + 2CO
140
CY6251 ENGINEERING CHEMISTRY II
SCE Dept. of S & H
2. Burning: Dry raw mix / slurry is carried out in rotary kiln.
The Dry raw mix / slurry is fed into the kiln from upper end and the flame is forced into the lower end.
Due to slope and slow rotation, the material gradually descends in the klin into different zones of
increasing temperatures.
(i). Drying Zone: Upper part of the kiln - About 400oc, water in slurry gets evaporated.
(ii). Calcination zone: Center part of the kiln - About 1000oc, limestone gets decomposed
intoCaO and CO2. CaCO3 ----- CaO + CO2
(iii). Clinkering Zone: Lowest part of the kiln - About 1350-1500oc, limestone reacts with
clay to form Bogue compounds. C2S,C3S,C3A,C4AF.
The Bogue compounds fuse together to form small, hard, grayish
coloured stone like mass called cement clinkers. 3. Grinding : The hot clinkers are cooled with atmospheric air and then pulverized together with 2-
3% gypsum in ball mills. Gypsum act as retarding agent for quick setting
cement.
4. Storage and Packing: The cement coming out of the grinding mill is stored in a concrete storage
silos. Then the cement is packed in jute bags by automatic
machine.
07. Explain the properties of Portland cement.
Properties: (i). Setting and Hardening of cement. (ii). Heat of Hydration. (i).
Setting and Hardening of cement.
Setting: It is defined as the stiffening of the original plastic mass, due to the formation of
tobermonite gel.
Hardening: It is defined as the development of strength due to formation of crystals. When
cement is mixed with water, results formation of gel and crystalline products.
Chemical reactions:
(i). Flash set – When cement is mixed with water, hydration of C3A takes place and the paste becomes
quite rigid within a short time.(1 Day)
C3A + 6H2O C3A.6H2O
(II). Formation of Tobermonite gel: After the hydration of C3A, C3S begins to hydrate to give Tobermonite
gel and crystalline Ca(OH)2. This is responsible for the development of initial strength of cement. The
hydration of C3S gets completed within 7 days. It does not contribute much to the
strength of cement.
141
CY6251 ENGINEERING CHEMISTRY II
SCE Dept. of S & H
C3S + 6H2O C3S2 .3H2O + 3Ca(OH)2
(III). Dicalcium silicate (C2S) reacts with water very slowly and gets completed in 7 to 28 days.
2C2S + 4H2O C3S2 .3H2O +Ca(OH)2
The increase in strength between 7 to 28 days is due to the formation of tobermonite gel and
crystalline Ca(OH)2.
(iv). The hydration of C4AF takes place initially, the hardening takes place finally through
crystallization along with C2S.
C4AF + 7H2O C3A.6H2O
142
CY6251 ENGINEERING CHEMISTRY II
SCE Dept. of S & H
Thus the final setting and hardening of cement is due to the formation of tobermonite gel plus
crystallization of Ca(OH)2 and hydrated tricalcium aluminate.
ii). Heat of Hydration:
When water is mixed with Portland cement some
amount of heat is liberated due to hydration and
hydrolysis reactions of Bogue compounds. The average
quantity of heat is liberated is 500 kJ/kg. 143
CY6251 ENGINEERING CHEMISTRY II
SCE Dept. of S & H
08. Write short notes on special cements like waterproof and white cement.
(i). Waterproof cement:
It is obtained by adding water- proof materials like calcium stearate, aluminium stearate and gypsum
with tannic acid to ordinary Portland cement during grinding.
Functions: (i). To make concrete impervious to water under pressure. (ii).
To resist the absorption of water.
Properties:
(i). It is more expensive than ordinary Portland cement. (ii).
It act as pore-blocking and water- repelling agent.
Uses: (i). Used in the construction bridges and structures under water.
(ii). White Cement:
It is white in color due to absence of iron compounds.
Such cements are made from raw materials which are free from iron oxide.
Properties:
(i). It is more expensive than ordinary Portland cement.
(ii). It act as pore-blocking and water- repelling agent.
Uses: works.
(i). Repairing and joining marble pillars and blocks, manufacture of tiles and mosaic (ii). Used in the construction bridges and structures under water.
09. Explain the manufacture the glass.
Raw materials:
a) Sodium is soda , Na2CO3 – Soft glass.
b) Potassium is potash, K2CO3 – Hard
glass. c) Calcium are limestone, chalk
and lime
d) Lead are litharge, and red lead – Flint
glass e) Silica are quartz, white sand.
f) Zinc is zinc oxide – Heat and shock proof glass
g) Borate are borax , and boric acid - Heat and shock proof
glass h) Cutlets or pieces of broken glass to increase the
fusibility. 4 steps involved for the manufacturing of glass.
144
CY6251 ENGINEERING CHEMISTRY II
SCE Dept. of S & H
1. Melting: The raw materials in proper proportions are mixed and finely powdered. This mixture called
batch is fused with some broken glass, called cullet in the pot of the tank furnace, in which heating is done
by burning produces gas and air mixture over the charge.
Heating is continued, till the molten mass is free from bubbles and glass-balls, and then cooled to about
800oC.
2. Foaming and shaping:
Molten glass is then worked into articles of desires shapes by either blowing or moulding or pressing
between rollers.
3. Annealing:
Glass articles are then allowed to cool gradually to room temperature( sudden cooling must be
avoided, because cracking occurs ). The longer the annealing period, the better quality of glass. 4. Finishing:
All glass articles after annealing are subjected to finsish processes such as cleaning, grinding,
polishing, cutting etc.
10. Explain the types and properties and uses of glass.
1) . Soda lime or soft glass:
Raw materials: silica, calcium carbonate and soda ash.
Approximate composition: Na2O.CaO.6SiO2
Properties:
a) They are low cost.
b) It is resistant to water.
c) It is attacked by common reagents like acids.
Uses: Window glasses, electric bulbs, bottles, jars, cheaper table wares, where high temperature –
resistance and chemical stability required. 2). Potash lime or Hard glass:
Raw materials: silica, calcium carbonate and Potassium carbonate.
Approximate composition: K2O.CaO.6SiO2
Properties:
a) Possess high melting point so it will not fuse easily.
b) Less acted upon by acids, alkali and other solvents than ordinary glasses. Uses:
Chemical apparatus, combustion tubes, which are to be used for heating operations. 3). Lead glass or Flint glass:
Raw materials: Lead oxide and silica are fused.
Approximate composition: K2O.PbO.6SiO2
145
CY6251 ENGINEERING CHEMISTRY II
SCE Dept. of S & H
Properties:
a) Lower softening temperature than soda- glass. b) Higher
refractive – index.
c) Has excellent electrical properties. d) High
specific gravity ( 3 to 3.3) Uses:
High quality table wares, optical purposes(like lenses), neon sign tubing, cathode ray tubes,
electrical insulators and in art objects.
High lead content glasses are used for extra-dense optical glasses for windows and
shields to protect personnel from x-rays and gamma rays in medical and atomic energy
fields respectively.
4). Boro silicate glass / Pyrex glass / Jena glass.
Raw materials: silica, boron with a small amount of alumina and some oxides. Approximate
composition: SiO2(80.5%),B2O3(13%), Al2O3(3%),K2O(3%),Na2O(0.5%)
Properties:
a) Low thermal efficient of expansion
b) High chemical resistance.
c) Very high softening points.
d) Excellent shock-proof.
Uses:
Used in industry for pipelines for corrosive liquids, gauge glasses, superior laboratory
apparatus, kitchenware, chemical plants, television tubes, electrical insulators.
5). Aluminosillicate glass
Raw materials: alumina, silica, boron with a small amount of and some oxides.
Approximate composition: SiO2(55%),Al2O3(23%),B2O3(7%), MgO(9%),CaO(5%),
Na2O+K2O(1%)
Properties:High softening temperature
Uses:
High-pressure mercury discharge tubes, chemical combustion tubes, certain domestic
equipments, etc, 6). Glass wool:
It is a fibrous wool-like material, composed of intermingled fine threads of filaments of glass. They are completely alkali free. The glass filaments are obtained by forcing molten glass through small offices. The average diameter of the office is 0.0005 to 0.007mm. Then the filaments of glass so obtained are thrown over a rapidly rotating drum to get wool-like materials
146
CY6251 ENGINEERING CHEMISTRY II
SCE Dept. of S & H
. Properties:
a). fire- proof and heat proof material.
b). low electrical and thermal conductivity.
c). resistant to water and most of chemicals. d). high
tensile strength – 8 times that of steel.
Uses:
1. Heat insulation purpose- domestic and industrial appliances.
2. Air filters and dust filtering materials.
3. Insulation of metal pipelines and walls and roofs of houses.
4. used in filtration of corrosive liquids like acids.
5. Manufacture of fibre-glass, by blending with plastic resins.
UNIT V
1. How fuels are classified. Give one example for each.
Based on Occurrence - 2 Types.
1. Primary Fuels – It occurs in nature such as. Ex: Coal, Crude oil, Natural Gas.
2. Secondary Fuels – It is derived from primary fuels. Ex: Coke, Petrol, Coal gas. Based
on physical state – 3 types
1. Solid fuels, eg., coal, coke,
2. Liquid fuels eg., gasoline, diesel.
3. Gaseous fuels eg., coal gas, natural gas.
2. Define calorific value. Explain higher & lower calorific value.
It is defined as the amount of heat obtainable by the complete combustion of a unit mass of the fuel.
Units of Calorific value ; Calorie, kilocalorie, British thermal unit, centigrade heat unit
Higher calorific value / Gross calorific value (GCV)
147
CY6251 ENGINEERING CHEMISTRY II
SCE Dept. of S & H
GCV = The total amount of heat is produced, when a unit quantity of the fuel is completely burnt and the
products of combustion are cooled to room temperature is known as GCV.
Lower calorific value / Net calorific value (GCV)
NCV = The total amount of heat is produced, when a unit quantity of the fuel is completely burnt and
products of combustion are allowed to escape is known as NCV
NCV = GCV -0.09H x 587.
3. Explain proximate analysis. Give its significance.
It involves the determination of % of moisture content, volatile matter, ash content &
fixed carbon in coal.
(i) Moisture content: About 1 gram of air-dried powdered coal sample is taken in a crucible & it is heated
at 100-105°C for 1 hour.
%of moisture in coal= loss in weight of the coal
X100
weight of Air- dried coal
(ii) Volatile matter: After the analysis of moisture content, the crucible with residual coal sample is
converted with lid & it is heated upto 950°C for 7 minutes.
% of Volatile mater in coal=
148
loss in weight of the coal
weight of moisture- free coal
X100
CY6251 ENGINEERING CHEMISTRY II
SCE Dept. of S & H
(iv) Fixed carbon: It is determined by the subtracting the sum total of moisture, volatile & ash content
from 100.
% of fixed carbon in coal = 100 - % of (moisture content + volatile matter + ash content)
Significance or importance of Proximate Analysis:
(i) High % of moisture is undesirable because it reduces the calorific value of a fuel, & increases the transport
cost.
(ii) High % of matter is undesirable because it reduces the calorific value of a fuel & coal burns with a long
flame & high smoke.
(iii) High % of ash content is undesirable because it reduces the calorific value of a fuel & makes the
additional cost of disposal of ash.
(iv) High % of fixed carbon in a coal, is greater its calorific value.
4. Explain ultimate analysis. Give its significance.
It involves the determination of % of Carbon, Hydrogen, Nitrogen, Sulphur & Oxygen in coal.
1. Carbon & Hydrogen: A known aount of coal sample is burnt with o2 in a combustion apparatus. In coal
carbon & hydrogen are converted into CO2 & H2O & those are absorbed by KOH tubes &
CaCl2 tubes.
C + O2 CO2
12 44
% of Carbon in coal =
Increase weight in KOHtubes X
12 X 100
Weight of coal sample taken 44
H2 + ½ O2 H2O
2 18
% of Hydrogen in coal = Increase weight inCaCl2 tubes
X 2
X 100
149
Weight of coal sample taken 18
CY6251 ENGINEERING CHEMISTRY II
SCE Dept. of S & H
1. Nitrogen:
It is carried out by Kjeldahl‟s method. A known amount of coal is heated
with Con. H2SO4 in presence of K2 SO4 catalyst in a long necked flask
called Kjeldahl‟s flask. Nitrogen is converted into ammonium sulphate.
Then it is heated with NaOH & absorbed by HCl.
% of Nitrogen in coal = 1.4 X volume of acid consumed
Weight of coal sample
3. Sulphur: A known amount of coal is completely burnt in a bomb calorimeter. Here
sulphur is converted into sulphate & treated with BaCl2, BaSO4 is obtained.
4. Oxygen: The % of oxygen is calculated as follows,
% of Oxygen in Coal = 100 - % of ( C + H+N+S+ash)
Importance or significance of Ultimate analysis:
1. Higher % of carbon & hydrogen, better is the quality of coal & higher its calorific value.
2. Should have very little nitrogen content.
3. Presence of sulphur is undesirable because it forms harmful gases during the combustion.
4. Lower of the Oxygen increases the higher its calorific value.
5. How Metallurgical coke is manufactured by Otto-Hoffman’s method?
When bituminous coal is heated strongly in the absence of air, the volatile matter
escapes out & the mass becomes hard, strong, porous, which is called metallurgical coke.
Manufacture of Metallurgical coke by “Otto- Hoffman’s by products”
method:
150
CY6251 ENGINEERING CHEMISTRY II
SCE Dept. of S & H
In order to (i) Increase the thermal efficiency of the carbonization
process & (ii) Recover the valuable by products by this
method.
This oven consists of a number of silica chambers.
Each chamber is about 10-12 m long, 3-4 m height & 0.4 – 0.45m wide.
Coal is introduced into the silica chambers & heated 1200°C by air & producer gas.
I & IV regenerators are heated by hot flue gases & II & III regenerators are
heated by incoming air & producergas.
When the process is complete, the coke is removed & cool by with water.
Time taken for this process is 12-20 hours.
The yield of the coke is about 70%
From out coming flue gas, it gives valuable products like Tar, ammonia, benzene.
H2S are obtained.
Recovery of by products:
(i) Tar: the flue gases are first passed through a tower, in which liq. NH3 is sprayed,
tar is collected at the bottom of the tank.
(ii) Ammonia: The gases are then passed through 2nd
tower, in which water is sprayed &
NH3
gets in the form of NH4OH.
(iii) Naphthalene: The gases are again passed through next tower, cooled water is
sprayed, Naphthalene gets & condensed.
(iv) Benzene: The gases are passed through next tower, petroleum oil is sprayed, benzene
gets condensed.
(v) H2S gas: The remaining gases are then passed through a purifier, H2S gas is obtained.
The final gas left out is called coal gas.
Advantages: (i) Valuable by product like NH3, benzene, etc are obtained.
(ii) The carbonization time is less.(iii) Heating is done by extremely by producer gas.
6. What do you mean by hydrogenation of coal? How Synthetic petrol is manufactured by
Bergius Process? Or How solid fuel is converted into liquid fuel? Explain in detail.
The preparation of liquid fuels from solid coal is known as hydrogenation of coal &
this gasoline is known as synthetic petrol.
151
CY6251 ENGINEERING CHEMISTRY II
SCE Dept. of S & H
Bergius Process – Direct method:
Input Powdered coal + Ni Oleate catalyst + Heavy oil are made into paste + H2
Heating in
400 - 450°C.
Pressure
200-250atm.
Process: Powdered coal is converted into gasoline.
In this process powdered coal is mixed with Ni oleate & heavy oil & made into paste.
It is pumped along with H2 gas into the converter, the paste is heated to 400 - 450°C
under pressure of 200-250atm.
Crude oil comes & it is fractionated into 3 parts.
1. Gasoline. 2. Middle oil. 3. Heavy oil.
The middle oil is further hydrogenated in vapour phase to get
gasoline. The heavy oil is recycled for making paste again coal
powder.
60% of yield is obtained from this process.
7. Explain the following (i) Compressed natural
gas (CNG) (ii) Liquid
petroleum gas. (LPG)
(i) Compressed Natural Gas: (CNG) Natural gas (CH4) compressed to a pressure of about 1000 atm is known as CNG.
Its calorific value is 12000-14000kcal/m3.
It is fully of methane only & derived from natural gas.
Its composition is as follows.
CH4 = 70-90% C2 H2 = 5- 10 % H2 = 3%
152
CY6251 ENGINEERING CHEMISTRY II
SCE Dept. of S & H
Uses: CNG is a cheapest, clearest & the least polluting fuel for automobiles instead of petrol
or diesel.
(ii) Liquid Petroleum Gas: (LPG)
It is obtained as a by- product during the cracking of heavy oil.
Its composition is
Butane
= 27%
Isobut
ene =
25%
Butyle
nes =
43%
Propan
e = 5%
Its calorific value is 27,800 kcal /m3.
LPG is marketed under the trade names like Indane, HP, Bharat gas in steel cylinders
under high pressure.
A small amount of Ethyl mercaptan is added during filling of cylinders to help in
detecting leakage of gas.
LPG ensures complete combustion with no smoke & causes the least
environmental pollution.
Uses: 1. It is used as a domestic fuel.
2. It is used as a fuel in vehicles (i.e) motor fuel.
3. It is used in industries & laboratories
8. Explain Water gas with reaction.
It is a mixture of CO & H2 with small amount of N2.
Its calorific value is about 2800kcal/m3.
Composition: CO = 41%, H2 = 51%, N2 = 4% & CO2 = 4%.
153
CY6251 ENGINEERING CHEMISTRY II
SCE Dept. of S & H
The water gas producer consists of a tall steel vessel, lined with refractory bricks.
It is provided with cup & cone feeder at the top & side opening for water gas exists. At the
bottom it is provided with 2 inlet pipes for passing air & steam.
When steam & little air is passed alternatively over a red hot coke maintained at
about 900-1000°C in a reactor, water gas is produced.
Two steps of reaction in production of water gas: Step 1: C + H2O CO + H2. ENDOTHERMIC
Coke steam water gas
Here the steam is passed through red hot coke, where CO & H2 gases are produced. The
reaction is endothermic.
Step 2: C + O2 CO2. EXOTHERMIC.
Uses: 1. It is used for preparation of power alcohol.
2. For the production of H2 & in synthesis of NH3.
3. To manufacture synthesis petrol in Fischer – Tropsh process.
9. Explain Producer gas with reaction.
It is a mixture of CO & N2 with small amount of
H2. Its calorific value is about 1300 kcal/m3.
Composition: CO = 30%, H2 = 10-15%, N2 = 51-56% & others = rest.
154
CY6251 ENGINEERING CHEMISTRY - II
SCE Dept.of S&H
The producer gas producer consists of a tall steel vessel, lined inside with refractory bricks. It
is provided with cup & cone feeder at the top & side opening for producer gas exit.
At the bottom it is provided with an one inlet for passing air & steam.
When a mixture of air & steam is passed over a red hot coke at 1100°C in a reactor, the
producer gas is produced.
C+O2 +N2 CO + N2.
Coke from air producer gas
Uses: It is a used as a reducing agent in metallurgical operations.
Used for heating muffle furnaces & open- hearth furnaces.
10. Describe flue gas analysis by Orsat’s apparatus method.
Flue gas analysis is carried out by Orsat apparatus method.
A mixture of gases like CO2, CO, O2 & N2 etc coming out from the combustion
chamber is called flue gases.
If the flue gas contains,
CO -- It indicates incomplete combustion &
O2 --It indicates excess supply of air used in combustion.
155
CY6251 ENGINEERING CHEMISTRY - II
SCE Dept.of S&H
Apparatus: It consists a horizontal tube. At one end this tube, U tube containing fused
CaCl2 is connected through 3 way stop cock. The other end is connected with a graduated
burette. The horizontal tube is also connected with 3 different absorption bulbs I, II, III for
absorbing CO2, CO and O2.
I bulb: It contains KOH solutions & it absorbs CO2 only.
II bulb: It contains Alkaline pyrogallol solution & it absorbs CO2, & O2
III bulb: It contains Ammoniacal cuprous chloride solution & it absorbs CO2,CO & O2
The 3 way stop cock is connected with flue gas supply & it is sucked into the burette & it is
adjusted by 100cc. then the 3 way stop cock is closed. In bulb I, co2 is absorbed by KOH
solution & I is closed & II stopcock is opened, O2 is absorbed by alkaline pyrogallol
solution. Now II is closed & III is opened. CO is absorbed by ammonical cuprous chloride.
The decrease in volume of the flue gas in the burette indicates the volume of I CO2, II
O2,
III CO respectively.
Significance: It gives an clear idea about the complete or incomplete process. 156
CY6251 ENGINEERING CHEMISTRY - II
SCE Dept.of S&H
Anna university Questions
1. How is flue gas analysed by orsat method? Explain with neat diagram (Apr.
Dec-06)
2. Define gross and net calorific values of a fuel. How are they related? (June-06)
3. Calculate the gross and net calorific value of coal having the following
compositions
C = 85%, H = 8%, S = 1%, N = 2% ash = 4% (May-07).
Exercise
1. A sample of coal was found to contain the following. C = 81%, H = 4%,
O=2% N = 1% the remaining being ash. Estimate the quantity of minimum air
required for the complete combustion of 1 kg of the sample, if 40% of the
excess air is supplied (Ans: 14.95kg).
2. Calculate the minimum amount of air required for complete combustion of
50kg of fuel containing 80% carbon, 6% hydrogen 2% sulphur and the rest
nitrogen by weight. (Ans: 572 kg).
3. A coal sample on analysis gives C = 75%, H2 = 52%, O2 = 12.8%, S = 2% and
the rest ash.Calculate the amount of air needed for the complete combustion, if
1kg of the coal is bunt with 30% excess air (Ans: 13kg).
4. A fuel contains C = 75%, H = 4%, O = 5%, S = 7% remaining ash. Calculate
the minimum quantity of air required for the complete combustion of 1kg of
fuel. (Ans: 10.18 kg).
5. What is the volume of air required for complete combustion of 1m3 of mixture
containing 80% CH4 and 20% C2H6 (Ans: 10.95m3)
157