Technical Data Sheet Product Code: CWI Residential Cavity Wall Insulation Member of Affiliate of DESCRIPTION FACING Cavity Wall Insulation (CWI) Cavity Wall Insulation is composed of fine, stable and uniformly textured inorganic glass fibers bonded together by non-water soluble and fire- retardant thermosetting and heat resistant resin, and formed into semi-rigid non- combustible and moisture repellent rectangular boards or slabs. It is free from coarse fibers and shot due to its mineral composition. Cavity Wall Insulation is available either unfaced with a silicon- based emulsion additive in the wool to make the product water-repellent, or with a factory-applied KRAFT vapor barrier facing or with an Aluminum Foil Fiberglass Reinforced Kraft Paper (FRK) facing. APPLICATION Cavity Wall Insulation is a semi- rigid board intended for use in commercial, institutional, industrial, agricultural and residential construction as thermal and acoustical insulation for interior, exterior and partial or fully cavity wall applications as well as in poultry farms precast structures, prefabricated houses and new residential villa construction. Kg/m 3 Ibs/ft 3 26 1.6 STANDARD NOMINAL DENSITY W/m·°K or Btu·in/hr·ft 2 ·°F (ASTM C 518) “K” or “ג” value at mean temperatures Nominal Manufacturing Specifications. Check for availability in other dimensions. NORMAL THERMAL CONDUCTIVITY STANDARD AVAILABLE PRODUCTS Mean Temperatures W/m·°K Btu·in/ hr·ft 2 ·°F 10 °C 50 °F 0.034 0.24 24 °C 75 °F 0.035 0.24 50 °C 122 °F 0.042 0.29 75 °C 167 °F 0.047 0.33 100 °C 212 °F 0.052 0.36 Thermal Resistance Thickness Width Length m 2 .°K/W hr.ft 2 .°F/Btu mm inch m inch m inch 1.00 6.00 25 1 1.2/0.6 48/24 1.0 40 38 1½ 1.2/0.6 48/24 10 40 1.40 8.00 50 2 1.2/0.6 48/24 1.0 40 64 2½ 1.2/0.6 48/24 10 40 2.15 12.00 75 3 1.2/0.6 48/24 1.0 40 Arabian Fiberglass Insulation Company Ltd. J.V. of Gulf Insulation Group (A Zamil Industrial Subsidiary) & Owens Corning Corp. ودةدس اجلفايزله من العالمواد ا الشركة العربية لنجز كورن وشركة أوين)لصناعة لزاملت الإحدى قطاعا( ليجيةعزل اموعة الاتيجية ب شراكة اسGulf Insulation Group
Transcript
DESCRIPTION
Cavity Wall Insulation is composed of fine, stable and uniformly textured inorganic glass fibers bonded together by non-water soluble and fire-retardant thermosetting and heat resistant resin, and formed into semi-rigid non-combustible and moisture repellent rectangular boards or slabs. It is free from coarse fibers and shot due to its mineral composition.
FACING
Cavity Wall Insulation is available either unfaced with a silicon-based emulsion additive in the wool to make the product water-repellent, or with a factory-applied kraft/asphalt vapour barrier facing or with an Aluminum Foil Fiberglass Reinforced Kraft Paper (FRK) facing.
STANDARD AVAILABLE PRODUCTS
Nominal Manufacturing Specifications.Check for availability in other dimensions.
NOMINAL THERMAL CONDUCTIVITY
(BS 874) (ASTM C 518)“K” or “ ” value at mean temperatures
Technical Data SheetProduct Code: CWI APPLICATION
Cavity Wall Insulation is a semi-rigid board intended for use in commercial, institutional, industrial, agricultural and residential construction as thermal and acoustical insulation for interior, exterior and partial or fully cavity wall applications as well as in poultry farms, precast structures, prefabricated houses and new residential villa construction.
STANDARD NOMINAL DENSITY
26-27 kg/m3 – 1.6 – 1.7lb/ft3
Member ofAffiliate of
* Standard Products and Sizes
Residential Cavity Wall Insulation
Mean Temperatures
W/m. °C Btu.in/ft2.hr.°F
10°C 50°F 0.034 0.24
24°C 75°F 0.035 0.24
50°C 122°F 0.042 0.29
75°C 167°F 0.047 0.33
100°C 212°F 0.052 0.36
Thermal Resistance
(m2.°C/W) (hr.ft2.°F/Btu)
Thickness
mm inch
Width
mm inch
Length Package
mm inch m2 / ft2
1.00 6.00 25 1 1200/600 48/24 1000 40 28.8 310
1.40 8.00 50 2 1200/600 48/24 1000 40 14.4 155
2.15 12.00 75 3 1200/600 48/24 1000 40 9.6 104
DESCRIPTION
Cavity Wall Insulation is composed of fine, stable and uniformly textured inorganic glass fibers bonded together by non-water soluble and fire-retardant thermosetting and heat resistant resin, and formed into semi-rigid non-combustible and moisture repellent rectangular boards or slabs. It is free from coarse fibers and shot due to its mineral composition.
FACING
Cavity Wall Insulation is available either unfaced with a silicon-based emulsion additive in the wool to make the product water-repellent, or with a factory-applied kraft/asphalt vapour barrier facing or with an Aluminum Foil Fiberglass Reinforced Kraft Paper (FRK) facing.
STANDARD AVAILABLE PRODUCTS
Nominal Manufacturing Specifications.Check for availability in other dimensions.
NOMINAL THERMAL CONDUCTIVITY
(BS 874) (ASTM C 518)“K” or “ ” value at mean temperatures
Technical Data SheetProduct Code: CWI APPLICATION
Cavity Wall Insulation is a semi-rigid board intended for use in commercial, institutional, industrial, agricultural and residential construction as thermal and acoustical insulation for interior, exterior and partial or fully cavity wall applications as well as in poultry farms, precast structures, prefabricated houses and new residential villa construction.
STANDARD NOMINAL DENSITY
26-27 kg/m3 – 1.6 – 1.7lb/ft3
Member ofAffiliate of
* Standard Products and Sizes
Residential Cavity Wall Insulation
Mean Temperatures
W/m. °C Btu.in/ft2.hr.°F
10°C 50°F 0.034 0.24
24°C 75°F 0.035 0.24
50°C 122°F 0.042 0.29
75°C 167°F 0.047 0.33
100°C 212°F 0.052 0.36
Thermal Resistance
(m2.°C/W) (hr.ft2.°F/Btu)
Thickness
mm inch
Width
mm inch
Length Package
mm inch m2 / ft2
1.00 6.00 25 1 1200/600 48/24 1000 40 28.8 310
1.40 8.00 50 2 1200/600 48/24 1000 40 14.4 155
2.15 12.00 75 3 1200/600 48/24 1000 40 9.6 104
Arabian Fiberglass Insulation Company Ltd.J.V. of Zamil Industrial & Owens Corning Corp.
Thickness Width Length Densities
mm inch mm inch m ft kg/m3 lb/ft3
25 1 400 16 10
to
36
33
to
120
10-12 0.625-0.75
38 1 ½ 410 16
50 2 600 24
64 2 ½ 610 24
75 3 1200 48
89 3 ½ 1220 48
Depending
on thickness100 4
150 6
Thickness Thermal conductivity(K)
Thermal resistance(R)
mm inch W/m.°C Btu.in/hr.ft2 °F m2.°C/W hr.ft2.°F/Btu
25 1 0.040 0.28 0.63 4
38 1 ½ 0.040 0.28 0.95 5
50 2 0.040 0.28 1.25 7
64 2 ½ 0.040 0.28 1.60 9
75 3 0.040 0.28 1.88 11
89 3 ½ 0.040 0.28 2.23 13
100 4 0.040 0.28 2.50 14
150 6 0.040 0.28 3.75 21
DESCRIPTION
Blanket Insulation is a highly efficient, light weight, strong, resilient and easy to handle flexible blanket insulation composed of fine, stable and uniformly textured inorganic glass fibers bonded together by a non-water soluble and fire retardant thermosetting and heat resistant resin.
It is free from coarse fiber and shot due to its mineral composition.
FACING
Blanket Insulation is available unfaced, or laminated with factory-applied Kraft Paper, Vinyl or Aluminum Foil Glass Reinforced Kraft (FRK) or other specific vapor barriers to prevent condensation.
STANDARD NOMINAL DIMENSIONS
Check for availability of other dimensions and densities.
NOMINAL THERMAL CONDUCTIVITY
(at 24°C or 75°F mean temperature) (ASTM C 518) (BS 874)
APPLICATION
Blanket Insulation is intended for use in commercial, institutional, industrial, agricultural and residential construction as thermal and acoustical insulation for the interior, exterior and cavity walls applications, partitions, prefabricated houses, poultry farms, ceilings and as back loading of existing ceiling systems.
DENSITY
10 kg/m3 (0.625 pcf)
Member ofAffiliate of
* Standard Products and Sizes
Blanket Insulation
Technical Data SheetProduct Code: BKT
Arabian Fiberglass Insulation Company Ltd.J.V. of Zamil Industrial & Owens Corning Corp.
Thickness Width Length Densities
mm inch mm inch m ft kg/m3 lb/ft3
25 1 400 16 10
to
36
33
to
120
10-12 0.625-0.75
38 1 ½ 410 16
50 2 600 24
64 2 ½ 610 24
75 3 1200 48
89 3 ½ 1220 48
Depending
on thickness100 4
150 6
Thickness Thermal conductivity(K)
Thermal resistance(R)
mm inch W/m.°C Btu.in/hr.ft2 °F m2.°C/W hr.ft2.°F/Btu
25 1 0.040 0.28 0.63 4
38 1 ½ 0.040 0.28 0.95 5
50 2 0.040 0.28 1.25 7
64 2 ½ 0.040 0.28 1.60 9
75 3 0.040 0.28 1.88 11
89 3 ½ 0.040 0.28 2.23 13
100 4 0.040 0.28 2.50 14
150 6 0.040 0.28 3.75 21
DESCRIPTION
Blanket Insulation is a highly efficient, light weight, strong, resilient and easy to handle flexible blanket insulation composed of fine, stable and uniformly textured inorganic glass fibers bonded together by a non-water soluble and fire retardant thermosetting and heat resistant resin.
It is free from coarse fiber and shot due to its mineral composition.
FACING
Blanket Insulation is available unfaced, or laminated with factory-applied Kraft Paper, Vinyl or Aluminum Foil Glass Reinforced Kraft (FRK) or other specific vapor barriers to prevent condensation.
STANDARD NOMINAL DIMENSIONS
Check for availability of other dimensions and densities.
NOMINAL THERMAL CONDUCTIVITY
(at 24°C or 75°F mean temperature) (ASTM C 518) (BS 874)
APPLICATION
Blanket Insulation is intended for use in commercial, institutional, industrial, agricultural and residential construction as thermal and acoustical insulation for the interior, exterior and cavity walls applications, partitions, prefabricated houses, poultry farms, ceilings and as back loading of existing ceiling systems.
DENSITY
10 kg/m3 (0.625 pcf)
Member ofAffiliate of
* Standard Products and Sizes
Blanket Insulation
Technical Data SheetProduct Code: BKT
Cavity Wall Insulation (CWI)
Cavity Wall Insulation is composed of fine, stable and uniformly textured inorganic glass fibers bonded together by non-water soluble and fire-retardant thermosetting and heat resistant resin, and formed into semi-rigid non-combustible and moisture repellent rectangular boards or slabs. It is free from coarse fibers and shot due to its mineral composition.
Cavity Wall Insulation is available either unfaced with a silicon-based emulsion additive in the wool to make the product water-repellent, or with a factory-applied KRAFT vapor barrier facing or with an Aluminum Foil Fiberglass Reinforced Kraft Paper (FRK) facing.
Arabian Fiberglass Insulation Company Ltd.J.V. of Zamil Industrial & Owens Corning Corp.
Thickness Width Length Densities
mm inch mm inch m ft kg/m3 lb/ft3
25 1 400 16 10
to
36
33
to
120
10-12 0.625-0.75
38 1 ½ 410 16
50 2 600 24
64 2 ½ 610 24
75 3 1200 48
89 3 ½ 1220 48
Depending
on thickness100 4
150 6
Thickness Thermal conductivity(K)
Thermal resistance(R)
mm inch W/m.°C Btu.in/hr.ft2 °F m2.°C/W hr.ft2.°F/Btu
25 1 0.040 0.28 0.63 4
38 1 ½ 0.040 0.28 0.95 5
50 2 0.040 0.28 1.25 7
64 2 ½ 0.040 0.28 1.60 9
75 3 0.040 0.28 1.88 11
89 3 ½ 0.040 0.28 2.23 13
100 4 0.040 0.28 2.50 14
150 6 0.040 0.28 3.75 21
DESCRIPTION
Blanket Insulation is a highly efficient, light weight, strong, resilient and easy to handle flexible blanket insulation composed of fine, stable and uniformly textured inorganic glass fibers bonded together by a non-water soluble and fire retardant thermosetting and heat resistant resin.
It is free from coarse fiber and shot due to its mineral composition.
FACING
Blanket Insulation is available unfaced, or laminated with factory-applied Kraft Paper, Vinyl or Aluminum Foil Glass Reinforced Kraft (FRK) or other specific vapor barriers to prevent condensation.
STANDARD NOMINAL DIMENSIONS
Check for availability of other dimensions and densities.
NOMINAL THERMAL CONDUCTIVITY
(at 24°C or 75°F mean temperature) (ASTM C 518) (BS 874)
APPLICATION
Blanket Insulation is intended for use in commercial, institutional, industrial, agricultural and residential construction as thermal and acoustical insulation for the interior, exterior and cavity walls applications, partitions, prefabricated houses, poultry farms, ceilings and as back loading of existing ceiling systems.
DENSITY
10 kg/m3 (0.625 pcf)
Member ofAffiliate of
* Standard Products and Sizes
Blanket Insulation
Technical Data SheetProduct Code: BKT
Cavity Wall Insulation is a semi- rigid board intended for use in commercial, institutional, industrial, agricultural and residential construction as thermal and acoustical insulation for interior, exterior and partial or fully cavity wall applications as well as in poultry farms precast structures, prefabricated houses and new residential villa construction.
Kg/m3 Ibs/ft3
26 1.6
STANDARD NOMINAL DENSITY
W/m·°K or Btu·in/hr·ft2·°F (ASTM C 518) “K” or “ג” value at mean temperatures
Nominal Manufacturing Specifications. Check for availability in other dimensions.
NORMAL THERMAL CONDUCTIVITY STANDARD AVAILABLE PRODUCTS
Surface Burning Characteristics(UL 723, ASTM E 84, ASTM E 136)
Base glass fiber is non-combustible when tested to ASTM E84.
Alkalinity
pH 9
Thermal Resistance “R” Value (Excluding Facing)(ASTM C 167)
“R” is a measure of the resistance to heat flow of a material of any given thickness. (“R” = m2. °C/W or hr. ft2. °F/Btu.)
R = where “T” = thickness and “K” or “ ” = thermal conductivity
Working Temperature Limitations (ASTM C 411)
Operating up to °260C (°500F) for the WGF faced product. At excessive temperatures, a limited migration of binder may occur in the insulation in contact with hot surface. This in no way impairs the performance of the insulation.
Mold Growth (ASTM D 2020, UL 181)
Does not breed or sustain mold, fungus, bacteria or rodents.
Corrosiveness (ASTM C 665)
Chemically inert. Will not cause or accelerate corrosion of steel, stainless steel, copper or aluminum, due to its particular inorganic and mineral composition.
Moisture Absorption (ASTM D07- B, ASTM C 553)
In conditions of %95 relative humidity at °49C for 96 hours, moisture absorption is less than %0.2 by volume, when tested in accordance with ASTM C 533. fiberglass products do not absorb moisture from the ambient air nor water by capillary attraction, only water under pressure can enter the insulation products but that will quickly dry out owing to the material’s open cell structure.
Specification Compliance
Quiet Liner Insulation complies with the property requirements of the following specifications:
• ASTM C 1071: For Acoustical Performance• NFPA 90 A: For Fire Resistance
• DCL ASTM - C 533 - C 547 - C 612 - C 665• CE-EN 13162
Friction Loss
According to TIMA AHS152-T Pressure loss, in W.G., Fiberglass Quiet Liner.
This chart is to be used in place of the standard friction loss chart published in the ASHRAE Handbook of fundamentals. For conversion of round equivalents to rectangular sizes, use Table C2- “Circular Equivalents of Rectangular Ducts for Equal Friction and Capacity” from the same reference. Tests conducted in accordance with TIMA AHS 152T.
Arabian Fiberglass Insulation Company Ltd.J.V. of Zamil Industrial & Owens Corning Corp.Technical Data Sheet
Product Code: CWI
Residential Cavity Wall Insulation
Working Temperature Limitations
-4°C to +350°C. At excessive temperatures, a limited migration of binder may occur in the insulation in contact with the hot surface. This in no way impairs the performance of the insulation.
Alkalinity
pH 9
Corrosiveness (ASTM C 665)
Chemically inert. Will not cause or accelerate corrosion of steel,stainless steel copper or aluminium, due to its particular inorganic and mineral composition.
Mold Growth (ASTM D 2020, UL-181)
Does not breed or sustain mold, fungus, bacteria or rodents.
Moisture Absorption (ASTM D-07 B, ASTM C 553)
In conditions of 95% relative humidity at 49°C for 96 hours, moisture absorption is less than 0.2% by volume when tested in accordance with ASTM C553. products do not absorb moisture from the ambient air nor water by capillary attraction, only water under pressure can enter the insulation products but that will quickly dry out owing to the material’s open cell structure.
Compressive Strength
12 PCF at 10% Deformation40 PCF at 25% Deformation
Base glass fiber is non combustible when tested to ASTM E 84.UNFACED: Flame Spread: 5 Smoke Developed: 0 Fuel Contributed : 0
Fire Properties
B.S. 476 PART 4 – Non combustibleB.S. 476 PART 5 – IgnitabilityB.S. 476 PART 6 – Fire propagationB.S. 476 PART 7 – Surface spread of flame – Class IClass ‘0’ fire rating to the building regulations section E 15
Specification Compliance
Cavity Wall Insulation complies with the property requirements of the following specifications:UNFACED: •U.S.FederalSpecificationHH-I-558B,FormA, Class I: Form B Type I, Class 7. •ASTMC612Classes1and2 •DCLASTM-C533-C547-C612-C665 •CE-EN13162
Thermal Resistance “R” Value (ASTM C 167)
“R” is a measure of the resistance to heat flow of a material of any given thickness. (“R” = m2. °C/W or hr. ft2. °F/Btu.)
R = where “T” = thickness and “K” or “ ” = thermal conductivity
Thermal Conductance, ‘C’-VALUE(ASTM C 518, ASTM C 177)
C = = W/m2.°C or Btu/hr.ft2.°F.
It is the ability of the product to conduct heat.
Thermal Transmittance (U Value)
Thermal transmittance is the rate of heat flow through unit area of a wall system when unit temperature difference exists between air on each side of the structure.
The U value is the reciprocal of the sum of the resistances of the component parts of the structure plus the resistance of the surfaces and any cavities within the structure.
“U” Value of typical Cavity Wall Construction
1
“R” (Total)1
Rso + R1 + RA + R2 + R3 + R4 + Rsi
“U” =
“U” =
T
K
1
R
Rso
“R” (Total) = Rso + R1+RA+R2+R3+R4+Rsi
R1 RA R2 R3 R4 Rsi
Thermal Resistance “R” Value (ASTM C 167)
“R” is a measure of the resistance to heat flow of a material of any given thickness.(“R” = m2·°K/W or hr·ft2·°F/Btu)
R = T where “T” = Thickness K and “K” or “λ” = Thermal Conductivity
Working Temperature Limitations (ASTM C 411)
-4°C to +350°C At Excessive temperatures, a limited migration of binder may occur in the insulation in contact with the hot surface. This in no way impairs the performance of the insulation.
Mold Growth (ASTM D 2020, UL 181)
Does not breed or sustain mold, fungus, bacteria or rodents.
Corrosiveness (ASTM C 665)
Chemically inert. Will not cause or accelerate corrosion of steel, stainless steel, copper or aluminum, due to its particular inorganic and mineral composition.
Alkalinity
pH 9
Surface Burning Characteristics(ASTM E 84, UL 723)
Base glass fiber is non-combustible when tested to ASTM E 84.
Cavity Wall Insulation (CWI)
Thermal Conductance “C” Value (ASTM C 518, ASTM C 177)
“C” It is ability of the product to conduct heat. (“C” = W/m2·°K or Btu/hr·ft2·°F)
C = 1 where “T” = Thickness R and “K” or “λ” = Thermal Conductance
Specification Compliance
Cavity Wall Insulation complies with the property requirements of the following specifications:DCL : ASTM C 612CE-EN : 1121-CPD-BA0136
Fire Properties
B.S. 476 PART 4 : Non Combustible B.S. 476 PART 5 : Ignitability B.S. 476 PART 6 : Fire Propagation B.S. 476 PART 7 : Surface Spread of Flame Class ‘O’ fire rating to the building regulations sections E15
Compressive Strength
12 PSF at 10 % Deformation
40 PSF at 25% Deformation
Thermal Resistance (U Value)
Thermal transmittance is the rate of heat flow through unit area of a wall system when unit temperature difference exists between air on each side of the structure.
The U value is the reciprocal of the sum of the resistances of the component parts of the structure plus the resistance of the sur-faces and any cavities within the structure.
Arabian Fiberglass Insulation Company Ltd.J.V. of Zamil Industrial & Owens Corning Corp.Technical Data Sheet
Product Code: CWI
Residential Cavity Wall Insulation
Working Temperature Limitations
-4°C to +350°C. At excessive temperatures, a limited migration of binder may occur in the insulation in contact with the hot surface. This in no way impairs the performance of the insulation.
Alkalinity
pH 9
Corrosiveness (ASTM C 665)
Chemically inert. Will not cause or accelerate corrosion of steel,stainless steel copper or aluminium, due to its particular inorganic and mineral composition.
Mold Growth (ASTM D 2020, UL-181)
Does not breed or sustain mold, fungus, bacteria or rodents.
Moisture Absorption (ASTM D-07 B, ASTM C 553)
In conditions of 95% relative humidity at 49°C for 96 hours, moisture absorption is less than 0.2% by volume when tested in accordance with ASTM C553. products do not absorb moisture from the ambient air nor water by capillary attraction, only water under pressure can enter the insulation products but that will quickly dry out owing to the material’s open cell structure.
Compressive Strength
12 PCF at 10% Deformation40 PCF at 25% Deformation
Base glass fiber is non combustible when tested to ASTM E 84.UNFACED: Flame Spread: 5 Smoke Developed: 0 Fuel Contributed : 0
Fire Properties
B.S. 476 PART 4 – Non combustibleB.S. 476 PART 5 – IgnitabilityB.S. 476 PART 6 – Fire propagationB.S. 476 PART 7 – Surface spread of flame – Class IClass ‘0’ fire rating to the building regulations section E 15
Specification Compliance
Cavity Wall Insulation complies with the property requirements of the following specifications:UNFACED: •U.S.FederalSpecificationHH-I-558B,FormA, Class I: Form B Type I, Class 7. •ASTMC612Classes1and2 •DCLASTM-C533-C547-C612-C665 •CE-EN13162
Thermal Resistance “R” Value (ASTM C 167)
“R” is a measure of the resistance to heat flow of a material of any given thickness. (“R” = m2. °C/W or hr. ft2. °F/Btu.)
R = where “T” = thickness and “K” or “ ” = thermal conductivity
Thermal Conductance, ‘C’-VALUE(ASTM C 518, ASTM C 177)
C = = W/m2.°C or Btu/hr.ft2.°F.
It is the ability of the product to conduct heat.
Thermal Transmittance (U Value)
Thermal transmittance is the rate of heat flow through unit area of a wall system when unit temperature difference exists between air on each side of the structure.
The U value is the reciprocal of the sum of the resistances of the component parts of the structure plus the resistance of the surfaces and any cavities within the structure.
“U” Value of typical Cavity Wall Construction
1
“R” (Total)1
Rso + R1 + RA + R2 + R3 + R4 + Rsi
“U” =
“U” =
T
K
1
R
Rso
“R” (Total) = Rso + R1+RA+R2+R3+R4+Rsi
R1 RA R2 R3 R4 Rsi
Cavity Wall Insulation products can be easily cut with a knife and neatly fitted into irregularly shaped areas.
For Vertical Applications:
Cavity Wall Insulation can be installed between furring, strips or Z channels. For enclosed applications the product can be impaled on impaling pins and/or adhered with adhesives.
For Horizontal Applications:
Cavity Wall Insulation can be installed by the use of impaling pins against horizontal surfaces.
On Masonry Surface:
Cavity Wall Insulation can be installed between withes and on wall faces with impaling pins, mechanical fasten-ers and/or adhesives.
On Precast Concrete:
Cavity Wall Insulation can be installed using impaling pins and/or appropriate adhesives.
Arabian Fiberglass Insulation Company Ltd.J.V. of Zamil Industrial & Owens Corning Corp.Arabian Fiberglass Insulation Company Ltd.
J.V. of Zamil Industrial & Owens Corning Corp.
Key
Thermal Resistance = T/KRso = T/K of outside surface air filmR1 = T/K of external wallRA = T/K of air spaceR2 = T/K of insulationR3 = T/K of internal wallR4 = T/K of internal finishRsi = T/K of inside surface air film
Sound Absorption Coefficient
ASTM C 423 - Mounting Type AProduct placed against a solid backing such as a block wall
Installation
CWI Insulation products can be easily cut with aknife and nealty fitted into irregularly shaped areas.
For Vertical Applications: CWI Insulation can be installed between furring
strips or Z channels. For enclosed applications the product can be impaled on impaling pins and/or adhered with adhesives.
For Horizontal Applications: CWI Insulation can be installed by the use of impaling
pins against horizontal surfaces.
On Masonry Surface: CWI Insulation can be installed between wythes and
on wall faces with impaling pins, mechanical fasteners and/or adhesives.
On Precast Concrete: CWI Insulationcan be installed using impaling pins
and/or appropriate adhesives.
ThicknessSound Absorption Coefficients
Octave Band Center Frequencies, Hz
(mm) (in) 125 250 500 1000 2000 4000 NRC
25 1 0.09 0.26 0.64 0.90 1.05 1.10 0.70
50 2 0.26 0.77 1.13 1.09 1.04 1.05 1.00
75 3 0.28 0.80 1.12 1.18 1.12 1.10 1.05
Performance & Physical Characteristics
Arabian Fiberglass Insulation Company Ltd.
Acoustical Performance (ASTM C 777-423)
Reverberation Chamber MethodSound Absorption Coefficients at Frequencies (Hz)
Installation Recommendation for flexible blanket
Quiet Liner Products are available in roll and board types. The desired application length can be easily measured and cut from the full size. Quiet Liner is applied to the interior
Product SoundAbsorption coefficient at one third octave
center frequencies (Hz)
TypeThickness
125 250 500 1000 2000 4000 NRCmm w
AQL 16025 1 0.09 0.24 0.49 0.85 0.83 0.77 0.60
50 2 0.34 0.59 0.93 0.94 0.94 0.98 0.85
AQL 24025 1 0.12 0.32 0.70 0.93 0.95 0.99 0.75
50 2 0.27 0.69 1.01 1.07 1.06 1.05 0.95
AQL 320
15 ½ 0.05 0.13 0.32 0.65 0.79 0.93 0.45
25 1 0.29 0.45 0.77 1.00 0.93 0.96 0.80
50 2 0.37 0.92 1.04 1.14 1.13 1.01 1.05
AQL 480
15 ½ 0.05 0.12 0.29 0.51 0.68 0.80 0.40
25 1 0.22 0.52 0.73 0.98 1.02 1.00 0.80
50 2 0.30 0.85 1.03 1.07 1.06 1.00 1.00
AQL 64025 1 0.06 0.19 0.62 0.83 0.90 0.95 0.65
50 2 0.21 0.75 1.00 1.00 1.00 0.95 0.95
of ducts and plenums with the black surface facing the air stream. Transverse joints are to be neatly butted, with no interruptions or gaps. Longitudinal to be overlapped and compressed.
Quiet Liner should be adhered to sheet metal ducts with %100 coverage of adhesive, and all exposed leading edges and all transverse joints coated with adhesive. (The adhesive shall conform to standard ASC-A7001 C1972- or as approved by the project consultant). The liner should be additionally secured with mechanical fasteners which will compress the product sufficiently to hold it firmly in place.
For velocities to 10 m/s: fasteners should start within 75 mm of the upstream transverse edges of the liner and 75 mm from longitudinal joints, and should be spaced at maximum of 300 mm from the corner break. Elsewhere, they should be a maximum 450 mm on centers except to be placed not more than 150 mm from a longitudinal joint and 300 mm from a corner break.
For velocities from 10 to 20 m/s: fasteners should be placed as above, except to be spaced at a maximum of 150 mm from the corner break. Elsewhere, they should be a maximum of 400 mm on centers except to be placed not more than 150 mm from the longitudinal joint and 300 mm from the corner break. In addition to the edge coating of transverse joints, longitudinal joints should be similarly coated with adhesive. For velocities from 20 to 30 m/s, fasteners should be similarly spaced as for 10 to 20 m/s. In addition, metal nosing should be installed to secure the liner at all upstream transverse edges.
The velocity rated side of liner must face the air flow.
Liner adhered to the conduct with %90 min. area coverage of adhesive.
No. Pins
Liner Interior Width
0 8” dn
2 16 -“9”
3 28 - “17”
4 40 - “29”
5 52 - “41”
6 64 - “53”
7 76 - “65”
8 88 - “77”
9 100 - “89”
When velocity exceeds 4000 FPM use metal nosing on every leading edge. Nosing may be formed on duct or by channel or Zee attach by screws, rivets or welds.
Maximum spacing for fasteners.Actual intervals are approximate.
VelocityDimensions
A B C D
2500 - 0 FPM 3” 12” 4” 18”
6000 - 2501 FPM 3” 6” 4” 16”
Alternatefoldedcorner
All transverseedges to becoated with
adhesiveDuct
section(typically)
4 Ft. or 5 Ft.)
A
D
D
A
B
B
CC
B
C
Lapped and butted corner
AIR FLOW
DETAIL - A
Performance & Physical Characteristics
The U value is the reciprocal of the sum of the resistances of the component of the structure plus the resistance of the surfaces and any cavities within the structure.
Working Temperature Limitations (ASTM C 411)
-4°C to +260°C. At excessive temperatures, a limited migration of binder may occur in the insulation in contact with the hot surface. This in no way impairs the performance of the insulation.
Alkalinity (ASTM C 871)
pH 9
Corrosiveness (ASTM C 665)
Chemically inert. Will not cause or accelerate corrosion of steel, stainless steel, copper or aluminum, due to its particular inorganic and mineral composition.
Mold Growth (ASTM D 2020, UL 181)
Does not breed or sustain mold, fungus, bacteria or rodents.
Moisture Absorption (ASTM D-07 B, ASTM C 553)
In conditions of 95% relative humidity at 49°C for 96 hours, moisture absorption is less than 0.2% by volume, when tested in accordance with ASTM C 533. fiberglass products do not absorb moisture from the ambient air nor water by capillary attraction, only water under pressure can enter the insulation products but that will quickly dry out owing to the material’s open cell structure.
Vapor Permeability (ASTM E96A)
KRAFT 1.00 PERMFRK 0.02 PERM
Puncture Resistance (ASTM D 781)
FRK 25 Units
Compressive Strength
PCF AT 10% DEFORMATION 5PCF AT 25% DEFORMATION 10
Surface Burning Characteristics(UL 723, ASTM E 84, ASTM E 136)
Base glass fiber is non-combustible when tested to ASTM E84.
Thermal Resistance “R” Value (Unfaced) (ASTM C 167)
“R” is a measure of the resistance to heat flow of a material of any given thickness. (“R” = m2.°C/W or hr. ft2.°F/Btu.)
R = where “T” = thickness and “K” or “ ” = thermal conductivity
Thermal Conductance, “C”- Value (ASTM C 518, ASTM C 177)
C = = W/m2.°C or Btu/hr.ft2.°F.
It is the ability of the product to conduct heat.
Thermal Transmittance (U Value)
Thermal transmittance is the rate of heat flow through unit area of a wall system when unit temperature difference exists between air on each side of the structure.
Fire Properties
B.S. 476 PART 4 – Non-combustibleB.S. 476 PART 5 – IgnitabilityB.S. 476 PART 6 – Fire propagationB.S. 476 PART 7 – Surface spread of flameClass ‘O’ fire rating to the building regulations section E15
Specification Compliance
Blanket Installation complies with the property requirements of the following specifications:•UNFACED - U.S. Federal spec. HH-I-521 E Type I•KRAFT FACED - U.S. Federal Spec. HH-I-521 E Type II, Class C•FRK FACED - U.S. Federal Spec. HH-I-521 F, Type III, Class A, ASTM C 665•DCL ASTM - C 533 - C 547 - C 612 - C 665•CE-EN 13162
Acoustical Performance (ASTM C 423)
Sound Absorption Coeffecients at Frequencies (Hz)
Table 1-1Sound Absorption Coeffecients
Fiberglass Blanket Insulation
1R
Product Type & Thickness
Mounting(1)
Sound Absorption CoefficientsOctave Band Center Frequencies, Hz
125 250 500 1000 2000 4000 NRC
3.5” (R-11), insulation exposed to sound A .34 .85 1.09 .97 .97 1.12 .95
6.0” (R-19), insulation exposed to sound A .64 1.14 1.09 .99 1.00 1.21 1.05
ENERGY SAVING ENVIRONMENTALLY FRIENDLY RECYCLED MATERIALS SOLUTION FOR GLOBAL WARMING
AFICO is committed to a greener, cleaner environment. AFICO have responded to this call for conservation by increasing the amounts of recycled materials in our products.
No maintenance is required. Cavity Wall Insulation have a high resistance to accidental damage from knocks and handling during installation and maintenance. Dimensionally stable under varying conditions of temperature and humidity, rot-proof, odourless, non-hygroscopic and will not sustain vermin or fungus due to its inorganic and mineral compositions.
The product will maintain its thermal properties throughout the lifetime of the construction and will not age. fibreglass is non toxic and not hazardous to health.
STORAGE
To avoid moisture in the building construction, insulation products stored outside must be kept dry. We recommend products to be always stored in covered and dry areas. is not liable for the damage resulting from inadequate utilization, loading and off loading and mishandling of its products.
WARRANTY
See manufacturer’s General Terms and Conditions of Sale. As and/or OC has no control over installation design,
installation workmanship, accessory materials, or conditions of application, and/or OC does not warrant the performance or results of any installation containing their products. This warranty disclaimer includes all implied warranties, including the warranties or merchantability and fitness for a particular purpose.
Arabian Fiberglass Insulation Company reserves the right to alter product specifications without prior notice, as part of its policy of continued development and improvement. The installation methods described in this leaflet are not compulsory. The choice of materials and methods of fixing are the decision of the specifier, consultant or contractor. For further information or advice on specification of products, contact your local sales office.
AVAILABILITY
Manufactured by Arabian Fiberglass Insulation Company, Ltd. (AFICO), member of Zamil Industrial, with headquarters and production facilities located in Dammam, Saudi Arabia, under license from and utilizing the manufacturing specifications and technology of Owens-Corning Corporation (OC), Toledo, Ohio, U.S.A.
Marketed throughout Saudi Arabia, the G.C.C. countries, the Middle East and the Far East. products are available directly from as well as through a vast and reliable network of local distributors.
ENERGY SAVING ENVIRONMENTALLY FRIENDLY RECYCLED MATERIALS SOLUTION FOR GLOBAL WARMING
AFICO is committed to a greener, cleaner environment. AFICO have responded to this call for conservation by increasing the amounts of recycled materials in our products.
No maintenance is required. Blanket Insulation have a high resistance to accidental damage from knocks and handling during installation and maintenance. Dimensionally stable under varying conditions of temperature and humidity, rot-proof, odourless, non-hygroscopic and will not sustain vermin or fungus due to its inorganic and mineral compositions.
The product will maintain its thermal properties throughout the lifetime of the construction and will not age. fibreglass is non toxic and not hazardous to health.
STORAGE
To avoid moisture in the building construction, insulation products stored outside must be kept dry. We recommend products to be always stored in covered and dry areas. is not liable for the damage resulting from inadequate utilization, loading and off loading and mishandling of its products.
WARRANTY
See manufacturer’s General Terms and Conditions of Sale. As and/or OC has no control over installation design,
installation workmanship, accessory materials, or conditions of application, and/or OC does not warrant the performance or results of any installation containing their products. This warranty disclaimer includes all implied warranties, including the warranties or merchantability and fitness for a particular purpose.
Arabian Fiberglass Insulation Company reserves the right to alter product specifications without prior notice, as part of its policy of continued development and improvement. The installation methods described in this leaflet are not compulsory. The choice of materials and methods of fixing are the decision of the specifier, consultant or contractor. For further information or advice on specification of products, contact your local sales office.
AVAILABILITY
Manufactured by Arabian Fiberglass Insulation Company, Ltd. (AFICO), member of Zamil Industrial, with headquarters and production facilities located in Dammam, Saudi Arabia, under license from and utilizing the manufacturing specifications and technology of Owens-Corning Corporation (OC), Toledo, Ohio, U.S.A.
Marketed throughout Saudi Arabia, the G.C.C. countries, the Middle East and the Far East. products are available directly from as well as through a vast and reliable network of local distributors.
ENERGY SAVING ENVIRONMENTALLY FRIENDLY RECYCLED MATERIALS SOLUTION FOR GLOBAL WARMING
AFICO is committed to a greener, cleaner environment. AFICO have responded to this call for conservation by increasing the amounts of recycled materials in our products.
No maintenance is required. Acoustical Ceiling Panels have a high resistance to accidental damage from knocks and handling during installation and maintenance. Dimensionally stable under varying conditions of temperature and humidity, rot-proof, odourless, non-hygroscopic and will not sustain vermin or fungus due to its inorganic and mineral compositions.
The product will maintain its thermal properties throughout the lifetime of the construction and will not age. fibreglass is non toxic and not hazardous to health.
STORAGE
To avoid moisture in the building construction, insulation products stored outside must be kept dry. We recommend products to be always stored in covered and dry areas. is not liable for the damage resulting from inadequate utilization, loading and off loading and mishandling of its products.
WARRANTY
See manufacturer’s General Terms and Conditions of Sale. As and/or OC has no control over installation design,
installation workmanship, accessory materials, or conditions of application, and/or OC does not warrant the performance or results of any installation containing their products. This warranty disclaimer includes all implied warranties, including the warranties or merchantability and fitness for a particular purpose.
Arabian Fiberglass Insulation Company reserves the right to alter product specifications without prior notice, as part of its policy of continued development and improvement. The
The choice of materials and methods of fixing are the decision of the specifier, consultant or contractor. For further information or advice on specification of products, contact your local sales office.
AVAILABILITY
Manufactured by Arabian Fiberglass Insulation Company, Ltd. (AFICO), member of Zamil Industrial, with headquarters and production facilities located in Dammam, Saudi Arabia,
and technology of Owens-Corning Corporation (OC), Toledo, Ohio, U.S.A.
Marketed throughout Saudi Arabia, the G.C.C. countries, the Middle East and the Far East. products are available directly from as well as through a vast and reliable network of local distributors.
Special products are manufactured on request.
Acoustical Ceiling PanelsTechnical Data SheetProduct Code: ACP
ENERGY SAVING ENVIRONMENTALLY FRIENDLY RECYCLED MATERIALS SOLUTION FOR GLOBAL WARMING
AFICO is committed to a greener, cleaner environment. AFICO have responded to this call for conservation by increasing the amounts of recycled materials in our products.
No maintenance is required. Acoustical Ceiling Panels have a high resistance to accidental damage from knocks and handling during installation and maintenance. Dimensionally stable under varying conditions of temperature and humidity, rot-proof, odourless, non-hygroscopic and will not sustain vermin or fungus due to its inorganic and mineral compositions.
The product will maintain its thermal properties throughout the lifetime of the construction and will not age. fibreglass is non toxic and not hazardous to health.
STORAGE
To avoid moisture in the building construction, insulation products stored outside must be kept dry. We recommend products to be always stored in covered and dry areas. is not liable for the damage resulting from inadequate utilization, loading and off loading and mishandling of its products.
WARRANTY
See manufacturer’s General Terms and Conditions of Sale. As and/or OC has no control over installation design,
installation workmanship, accessory materials, or conditions of application, and/or OC does not warrant the performance or results of any installation containing their products. This warranty disclaimer includes all implied warranties, including the warranties or merchantability and fitness for a particular purpose.
Arabian Fiberglass Insulation Company reserves the right to alter product specifications without prior notice, as part of its policy of continued development and improvement. The installation methods described in this leaflet are not compulsory. The choice of materials and methods of fixing are the decision of the specifier, consultant or contractor. For further information or advice on specification of products, contact your local sales office.
AVAILABILITY
Manufactured by Arabian Fiberglass Insulation Company, Ltd. (AFICO), member of Zamil Industrial, with headquarters and production facilities located in Dammam, Saudi Arabia, under license from and utilizing the manufacturing specifications and technology of Owens-Corning Corporation (OC), Toledo, Ohio, U.S.A.
Marketed throughout Saudi Arabia, the G.C.C. countries, the Middle East and the Far East. products are available directly from as well as through a vast and reliable network of local distributors.
Special products are manufactured on request.
Acoustical Ceiling PanelsTechnical Data SheetProduct Code: ACP
ENERGY SAVING ENVIRONMENTALLY FRIENDLY RECYCLED MATERIALS SOLUTION FOR GLOBAL WARMING
AFICO is committed to a greener, cleaner environment. AFICO have responded to this call for conservation by increasing the amounts of recycled materials in our products.
No maintenance is required. Blanket Insulation have a high resistance to accidental damage from knocks and handling during installation and maintenance. Dimensionally stable under varying conditions of temperature and humidity, rot-proof, odourless, non-hygroscopic and will not sustain vermin or fungus due to its inorganic and mineral compositions.
The product will maintain its thermal properties throughout the lifetime of the construction and will not age. fibreglass is non toxic and not hazardous to health.
STORAGE
To avoid moisture in the building construction, insulation products stored outside must be kept dry. We recommend products to be always stored in covered and dry areas. is not liable for the damage resulting from inadequate utilization, loading and off loading and mishandling of its products.
WARRANTY
See manufacturer’s General Terms and Conditions of Sale. As and/or OC has no control over installation design,
installation workmanship, accessory materials, or conditions of application, and/or OC does not warrant the performance or results of any installation containing their products. This warranty disclaimer includes all implied warranties, including the warranties or merchantability and fitness for a particular purpose.
Arabian Fiberglass Insulation Company reserves the right to alter product specifications without prior notice, as part of its policy of continued development and improvement. The installation methods described in this leaflet are not compulsory. The choice of materials and methods of fixing are the decision of the specifier, consultant or contractor. For further information or advice on specification of products, contact your local sales office.
AVAILABILITY
Manufactured by Arabian Fiberglass Insulation Company, Ltd. (AFICO), member of Zamil Industrial, with headquarters and production facilities located in Dammam, Saudi Arabia, under license from and utilizing the manufacturing specifications and technology of Owens-Corning Corporation (OC), Toledo, Ohio, U.S.A.
Marketed throughout Saudi Arabia, the G.C.C. countries, the Middle East and the Far East. products are available directly from as well as through a vast and reliable network of local distributors.
ENERGY SAVING ENVIRONMENTALLY FRIENDLY RECYCLED MATERIALS SOLUTION FOR GLOBAL WARMING
AFICO is committed to a greener, cleaner environment. AFICO have responded to this call for conservation by increasing the amounts of recycled materials in our products.
No maintenance is required. Acoustical Ceiling Panels have a high resistance to accidental damage from knocks and handling during installation and maintenance. Dimensionally stable under varying conditions of temperature and humidity, rot-proof, odourless, non-hygroscopic and will not sustain vermin or fungus due to its inorganic and mineral compositions.
The product will maintain its thermal properties throughout the lifetime of the construction and will not age. fibreglass is non toxic and not hazardous to health.
STORAGE
To avoid moisture in the building construction, insulation products stored outside must be kept dry. We recommend products to be always stored in covered and dry areas. is not liable for the damage resulting from inadequate utilization, loading and off loading and mishandling of its products.
WARRANTY
See manufacturer’s General Terms and Conditions of Sale. As and/or OC has no control over installation design,
installation workmanship, accessory materials, or conditions of application, and/or OC does not warrant the performance or results of any installation containing their products. This warranty disclaimer includes all implied warranties, including the warranties or merchantability and fitness for a particular purpose.
Arabian Fiberglass Insulation Company reserves the right to alter product specifications without prior notice, as part of its policy of continued development and improvement. The
The choice of materials and methods of fixing are the decision of the specifier, consultant or contractor. For further information or advice on specification of products, contact your local sales office.
AVAILABILITY
Manufactured by Arabian Fiberglass Insulation Company, Ltd. (AFICO), member of Zamil Industrial, with headquarters and production facilities located in Dammam, Saudi Arabia,
and technology of Owens-Corning Corporation (OC), Toledo, Ohio, U.S.A.
Marketed throughout Saudi Arabia, the G.C.C. countries, the Middle East and the Far East. products are available directly from as well as through a vast and reliable network of local distributors.
Special products are manufactured on request.
Acoustical Ceiling PanelsTechnical Data SheetProduct Code: ACP
ENERGY SAVING ENVIRONMENTALLY FRIENDLY RECYCLED MATERIALS SOLUTION FOR GLOBAL WARMING
AFICO is committed to a greener, cleaner environment. AFICO have responded to this call for conservation by increasing the amounts of recycled materials in our products.
No maintenance is required. Acoustical Ceiling Panels have a high resistance to accidental damage from knocks and handling during installation and maintenance. Dimensionally stable under varying conditions of temperature and humidity, rot-proof, odourless, non-hygroscopic and will not sustain vermin or fungus due to its inorganic and mineral compositions.
The product will maintain its thermal properties throughout the lifetime of the construction and will not age. fibreglass is non toxic and not hazardous to health.
STORAGE
To avoid moisture in the building construction, insulation products stored outside must be kept dry. We recommend products to be always stored in covered and dry areas. is not liable for the damage resulting from inadequate utilization, loading and off loading and mishandling of its products.
WARRANTY
See manufacturer’s General Terms and Conditions of Sale. As and/or OC has no control over installation design,
installation workmanship, accessory materials, or conditions of application, and/or OC does not warrant the performance or results of any installation containing their products. This warranty disclaimer includes all implied warranties, including the warranties or merchantability and fitness for a particular purpose.
Arabian Fiberglass Insulation Company reserves the right to alter product specifications without prior notice, as part of its policy of continued development and improvement. The installation methods described in this leaflet are not compulsory. The choice of materials and methods of fixing are the decision of the specifier, consultant or contractor. For further information or advice on specification of products, contact your local sales office.
AVAILABILITY
Manufactured by Arabian Fiberglass Insulation Company, Ltd. (AFICO), member of Zamil Industrial, with headquarters and production facilities located in Dammam, Saudi Arabia, under license from and utilizing the manufacturing specifications and technology of Owens-Corning Corporation (OC), Toledo, Ohio, U.S.A.
Marketed throughout Saudi Arabia, the G.C.C. countries, the Middle East and the Far East. products are available directly from as well as through a vast and reliable network of local distributors.
Special products are manufactured on request.
Acoustical Ceiling PanelsTechnical Data SheetProduct Code: ACP
See manufacturer’s General Terms and Conditions of Sale. As and/or OCF has no control over installation design, installation workmanship, accessory materials, or conditions of application, and/or OCF does not warrant the performance or results of any installation containing their products. This warranty disclaimer includes all implied warranties, including the warranties or merchantability and fitness for a particular purpose.
Arabian Fiberglass Insulation Company reserves the right to alter product specifications without prior notice, as part of its policy of continued development and improvement. The installation methods described in this leaflet are not compulsory. The choice of materials and methods of fixing are the decision of the specifier, consultant or contractor. For further information or advice on specification of products, contact your local sales office.
ENERGY SAVING ENVIRONMENTALLY FRIENDLY RECYCLED MATERIALS SOLUTION FOR GLOBAL WARMING
AFICO is committed to a greener, cleaner environment. AFICO have responded to this call for conservation by increasing the amounts of recycled materials in our products.
No maintenance is required. Blanket Insulation have a high resistance to accidental damage from knocks and handling during installation and maintenance. Dimensionally stable under varying conditions of temperature and humidity, rot-proof, odourless, non-hygroscopic and will not sustain vermin or fungus due to its inorganic and mineral compositions.
The product will maintain its thermal properties throughout the lifetime of the construction and will not age. fibreglass is non toxic and not hazardous to health.
STORAGE
To avoid moisture in the building construction, insulation products stored outside must be kept dry. We recommend products to be always stored in covered and dry areas. is not liable for the damage resulting from inadequate utilization, loading and off loading and mishandling of its products.
WARRANTY
See manufacturer’s General Terms and Conditions of Sale. As and/or OC has no control over installation design,
installation workmanship, accessory materials, or conditions of application, and/or OC does not warrant the performance or results of any installation containing their products. This warranty disclaimer includes all implied warranties, including the warranties or merchantability and fitness for a particular purpose.
Arabian Fiberglass Insulation Company reserves the right to alter product specifications without prior notice, as part of its policy of continued development and improvement. The installation methods described in this leaflet are not compulsory. The choice of materials and methods of fixing are the decision of the specifier, consultant or contractor. For further information or advice on specification of products, contact your local sales office.
AVAILABILITY
Manufactured by Arabian Fiberglass Insulation Company, Ltd. (AFICO), member of Zamil Industrial, with headquarters and production facilities located in Dammam, Saudi Arabia, under license from and utilizing the manufacturing specifications and technology of Owens-Corning Corporation (OC), Toledo, Ohio, U.S.A.
Marketed throughout Saudi Arabia, the G.C.C. countries, the Middle East and the Far East. products are available directly from as well as through a vast and reliable network of local distributors.
ENERGY SAVING ENVIRONMENTALLY FRIENDLY RECYCLED MATERIALS SOLUTION FOR GLOBAL WARMING
AFICO is committed to a greener, cleaner environment. AFICO have responded to this call for conservation by increasing the amounts of recycled materials in our products.
No maintenance is required. Acoustical Ceiling Panels have a high resistance to accidental damage from knocks and handling during installation and maintenance. Dimensionally stable under varying conditions of temperature and humidity, rot-proof, odourless, non-hygroscopic and will not sustain vermin or fungus due to its inorganic and mineral compositions.
The product will maintain its thermal properties throughout the lifetime of the construction and will not age. fibreglass is non toxic and not hazardous to health.
STORAGE
To avoid moisture in the building construction, insulation products stored outside must be kept dry. We recommend products to be always stored in covered and dry areas. is not liable for the damage resulting from inadequate utilization, loading and off loading and mishandling of its products.
WARRANTY
See manufacturer’s General Terms and Conditions of Sale. As and/or OC has no control over installation design,
installation workmanship, accessory materials, or conditions of application, and/or OC does not warrant the performance or results of any installation containing their products. This warranty disclaimer includes all implied warranties, including the warranties or merchantability and fitness for a particular purpose.
Arabian Fiberglass Insulation Company reserves the right to alter product specifications without prior notice, as part of its policy of continued development and improvement. The
The choice of materials and methods of fixing are the decision of the specifier, consultant or contractor. For further information or advice on specification of products, contact your local sales office.
AVAILABILITY
Manufactured by Arabian Fiberglass Insulation Company, Ltd. (AFICO), member of Zamil Industrial, with headquarters and production facilities located in Dammam, Saudi Arabia,
and technology of Owens-Corning Corporation (OC), Toledo, Ohio, U.S.A.
Marketed throughout Saudi Arabia, the G.C.C. countries, the Middle East and the Far East. products are available directly from as well as through a vast and reliable network of local distributors.
Special products are manufactured on request.
Acoustical Ceiling PanelsTechnical Data SheetProduct Code: ACP
ENERGY SAVING ENVIRONMENTALLY FRIENDLY RECYCLED MATERIALS SOLUTION FOR GLOBAL WARMING
AFICO is committed to a greener, cleaner environment. AFICO have responded to this call for conservation by increasing the amounts of recycled materials in our products.
No maintenance is required. Acoustical Ceiling Panels have a high resistance to accidental damage from knocks and handling during installation and maintenance. Dimensionally stable under varying conditions of temperature and humidity, rot-proof, odourless, non-hygroscopic and will not sustain vermin or fungus due to its inorganic and mineral compositions.
The product will maintain its thermal properties throughout the lifetime of the construction and will not age. fibreglass is non toxic and not hazardous to health.
STORAGE
To avoid moisture in the building construction, insulation products stored outside must be kept dry. We recommend products to be always stored in covered and dry areas. is not liable for the damage resulting from inadequate utilization, loading and off loading and mishandling of its products.
WARRANTY
See manufacturer’s General Terms and Conditions of Sale. As and/or OC has no control over installation design,
installation workmanship, accessory materials, or conditions of application, and/or OC does not warrant the performance or results of any installation containing their products. This warranty disclaimer includes all implied warranties, including the warranties or merchantability and fitness for a particular purpose.
Arabian Fiberglass Insulation Company reserves the right to alter product specifications without prior notice, as part of its policy of continued development and improvement. The installation methods described in this leaflet are not compulsory. The choice of materials and methods of fixing are the decision of the specifier, consultant or contractor. For further information or advice on specification of products, contact your local sales office.
AVAILABILITY
Manufactured by Arabian Fiberglass Insulation Company, Ltd. (AFICO), member of Zamil Industrial, with headquarters and production facilities located in Dammam, Saudi Arabia, under license from and utilizing the manufacturing specifications and technology of Owens-Corning Corporation (OC), Toledo, Ohio, U.S.A.
Marketed throughout Saudi Arabia, the G.C.C. countries, the Middle East and the Far East. products are available directly from as well as through a vast and reliable network of local distributors.
Special products are manufactured on request.
Acoustical Ceiling PanelsTechnical Data SheetProduct Code: ACP
For more information call the insulation professionals:
No maintenance is required. Cavity Wall Insulation have a high resistance to accidental damage from knocks and handling during installation and maintenance. Dimensionally stable under varying conditions of temperature and humidity, rot proof, odorless, non-hygroscopic and will not sustain vermin or fungus due to its inorganic and mineral compositions.
The product will maintain its thermal properties throughout the lifetime of the construction and will not age. fiberglass is non toxic and not hazardous to health.
To avoid moisture in the building construction, insulation products stored outside must be kept dry. We recommend products to be always stored in covered and dry areas. is not liable for the damage resulting from inadequate utilization, loading and off loading and mishandling of its products.
ENERGY SAVING ENVIRONMENTALLY FRIENDLY RECYCLED MATERIALS SOLUTION FOR GLOBAL WARMING
AFICO is committed to a greener, cleaner environment. AFICO have responded to this call for conservation by increasing the amounts of recycled materials in our products.
No maintenance is required. Blanket Insulation have a high resistance to accidental damage from knocks and handling during installation and maintenance. Dimensionally stable under varying conditions of temperature and humidity, rot-proof, odourless, non-hygroscopic and will not sustain vermin or fungus due to its inorganic and mineral compositions.
The product will maintain its thermal properties throughout the lifetime of the construction and will not age. fibreglass is non toxic and not hazardous to health.
STORAGE
To avoid moisture in the building construction, insulation products stored outside must be kept dry. We recommend products to be always stored in covered and dry areas. is not liable for the damage resulting from inadequate utilization, loading and off loading and mishandling of its products.
WARRANTY
See manufacturer’s General Terms and Conditions of Sale. As and/or OC has no control over installation design,
installation workmanship, accessory materials, or conditions of application, and/or OC does not warrant the performance or results of any installation containing their products. This warranty disclaimer includes all implied warranties, including the warranties or merchantability and fitness for a particular purpose.
Arabian Fiberglass Insulation Company reserves the right to alter product specifications without prior notice, as part of its policy of continued development and improvement. The installation methods described in this leaflet are not compulsory. The choice of materials and methods of fixing are the decision of the specifier, consultant or contractor. For further information or advice on specification of products, contact your local sales office.
AVAILABILITY
Manufactured by Arabian Fiberglass Insulation Company, Ltd. (AFICO), member of Zamil Industrial, with headquarters and production facilities located in Dammam, Saudi Arabia, under license from and utilizing the manufacturing specifications and technology of Owens-Corning Corporation (OC), Toledo, Ohio, U.S.A.
Marketed throughout Saudi Arabia, the G.C.C. countries, the Middle East and the Far East. products are available directly from as well as through a vast and reliable network of local distributors.
ENERGY SAVING ENVIRONMENTALLY FRIENDLY RECYCLED MATERIALS SOLUTION FOR GLOBAL WARMING
AFICO is committed to a greener, cleaner environment. AFICO have responded to this call for conservation by increasing the amounts of recycled materials in our products.
No maintenance is required. Acoustical Ceiling Panels have a high resistance to accidental damage from knocks and handling during installation and maintenance. Dimensionally stable under varying conditions of temperature and humidity, rot-proof, odourless, non-hygroscopic and will not sustain vermin or fungus due to its inorganic and mineral compositions.
The product will maintain its thermal properties throughout the lifetime of the construction and will not age. fibreglass is non toxic and not hazardous to health.
STORAGE
To avoid moisture in the building construction, insulation products stored outside must be kept dry. We recommend products to be always stored in covered and dry areas. is not liable for the damage resulting from inadequate utilization, loading and off loading and mishandling of its products.
WARRANTY
See manufacturer’s General Terms and Conditions of Sale. As and/or OC has no control over installation design,
installation workmanship, accessory materials, or conditions of application, and/or OC does not warrant the performance or results of any installation containing their products. This warranty disclaimer includes all implied warranties, including the warranties or merchantability and fitness for a particular purpose.
Arabian Fiberglass Insulation Company reserves the right to alter product specifications without prior notice, as part of its policy of continued development and improvement. The
The choice of materials and methods of fixing are the decision of the specifier, consultant or contractor. For further information or advice on specification of products, contact your local sales office.
AVAILABILITY
Manufactured by Arabian Fiberglass Insulation Company, Ltd. (AFICO), member of Zamil Industrial, with headquarters and production facilities located in Dammam, Saudi Arabia,
and technology of Owens-Corning Corporation (OC), Toledo, Ohio, U.S.A.
Marketed throughout Saudi Arabia, the G.C.C. countries, the Middle East and the Far East. products are available directly from as well as through a vast and reliable network of local distributors.
Special products are manufactured on request.
Acoustical Ceiling PanelsTechnical Data SheetProduct Code: ACP
ENERGY SAVING ENVIRONMENTALLY FRIENDLY RECYCLED MATERIALS SOLUTION FOR GLOBAL WARMING
AFICO is committed to a greener, cleaner environment. AFICO have responded to this call for conservation by increasing the amounts of recycled materials in our products.
No maintenance is required. Acoustical Ceiling Panels have a high resistance to accidental damage from knocks and handling during installation and maintenance. Dimensionally stable under varying conditions of temperature and humidity, rot-proof, odourless, non-hygroscopic and will not sustain vermin or fungus due to its inorganic and mineral compositions.
The product will maintain its thermal properties throughout the lifetime of the construction and will not age. fibreglass is non toxic and not hazardous to health.
STORAGE
To avoid moisture in the building construction, insulation products stored outside must be kept dry. We recommend products to be always stored in covered and dry areas. is not liable for the damage resulting from inadequate utilization, loading and off loading and mishandling of its products.
WARRANTY
See manufacturer’s General Terms and Conditions of Sale. As and/or OC has no control over installation design,
installation workmanship, accessory materials, or conditions of application, and/or OC does not warrant the performance or results of any installation containing their products. This warranty disclaimer includes all implied warranties, including the warranties or merchantability and fitness for a particular purpose.
Arabian Fiberglass Insulation Company reserves the right to alter product specifications without prior notice, as part of its policy of continued development and improvement. The installation methods described in this leaflet are not compulsory. The choice of materials and methods of fixing are the decision of the specifier, consultant or contractor. For further information or advice on specification of products, contact your local sales office.
AVAILABILITY
Manufactured by Arabian Fiberglass Insulation Company, Ltd. (AFICO), member of Zamil Industrial, with headquarters and production facilities located in Dammam, Saudi Arabia, under license from and utilizing the manufacturing specifications and technology of Owens-Corning Corporation (OC), Toledo, Ohio, U.S.A.
Marketed throughout Saudi Arabia, the G.C.C. countries, the Middle East and the Far East. products are available directly from as well as through a vast and reliable network of local distributors.
Special products are manufactured on request.
Acoustical Ceiling PanelsTechnical Data SheetProduct Code: ACP
ENERGY SAVING ENVIRONMENTALLY FRIENDLY RECYCLED MATERIALS SOLUTION FOR GLOBAL WARMING
AFICO is committed to a greener, cleaner environment. AFICO have responded to this call for conservation by increasing the amounts of recycled materials in our products.
No maintenance is required. Blanket Insulation have a high resistance to accidental damage from knocks and handling during installation and maintenance. Dimensionally stable under varying conditions of temperature and humidity, rot-proof, odourless, non-hygroscopic and will not sustain vermin or fungus due to its inorganic and mineral compositions.
The product will maintain its thermal properties throughout the lifetime of the construction and will not age. fibreglass is non toxic and not hazardous to health.
STORAGE
To avoid moisture in the building construction, insulation products stored outside must be kept dry. We recommend products to be always stored in covered and dry areas. is not liable for the damage resulting from inadequate utilization, loading and off loading and mishandling of its products.
WARRANTY
See manufacturer’s General Terms and Conditions of Sale. As and/or OC has no control over installation design,
installation workmanship, accessory materials, or conditions of application, and/or OC does not warrant the performance or results of any installation containing their products. This warranty disclaimer includes all implied warranties, including the warranties or merchantability and fitness for a particular purpose.
Arabian Fiberglass Insulation Company reserves the right to alter product specifications without prior notice, as part of its policy of continued development and improvement. The installation methods described in this leaflet are not compulsory. The choice of materials and methods of fixing are the decision of the specifier, consultant or contractor. For further information or advice on specification of products, contact your local sales office.
AVAILABILITY
Manufactured by Arabian Fiberglass Insulation Company, Ltd. (AFICO), member of Zamil Industrial, with headquarters and production facilities located in Dammam, Saudi Arabia, under license from and utilizing the manufacturing specifications and technology of Owens-Corning Corporation (OC), Toledo, Ohio, U.S.A.
Marketed throughout Saudi Arabia, the G.C.C. countries, the Middle East and the Far East. products are available directly from as well as through a vast and reliable network of local distributors.
ENERGY SAVING ENVIRONMENTALLY FRIENDLY RECYCLED MATERIALS SOLUTION FOR GLOBAL WARMING
AFICO is committed to a greener, cleaner environment. AFICO have responded to this call for conservation by increasing the amounts of recycled materials in our products.
No maintenance is required. Acoustical Ceiling Panels have a high resistance to accidental damage from knocks and handling during installation and maintenance. Dimensionally stable under varying conditions of temperature and humidity, rot-proof, odourless, non-hygroscopic and will not sustain vermin or fungus due to its inorganic and mineral compositions.
The product will maintain its thermal properties throughout the lifetime of the construction and will not age. fibreglass is non toxic and not hazardous to health.
STORAGE
To avoid moisture in the building construction, insulation products stored outside must be kept dry. We recommend products to be always stored in covered and dry areas. is not liable for the damage resulting from inadequate utilization, loading and off loading and mishandling of its products.
WARRANTY
See manufacturer’s General Terms and Conditions of Sale. As and/or OC has no control over installation design,
installation workmanship, accessory materials, or conditions of application, and/or OC does not warrant the performance or results of any installation containing their products. This warranty disclaimer includes all implied warranties, including the warranties or merchantability and fitness for a particular purpose.
Arabian Fiberglass Insulation Company reserves the right to alter product specifications without prior notice, as part of its policy of continued development and improvement. The
The choice of materials and methods of fixing are the decision of the specifier, consultant or contractor. For further information or advice on specification of products, contact your local sales office.
AVAILABILITY
Manufactured by Arabian Fiberglass Insulation Company, Ltd. (AFICO), member of Zamil Industrial, with headquarters and production facilities located in Dammam, Saudi Arabia,
and technology of Owens-Corning Corporation (OC), Toledo, Ohio, U.S.A.
Marketed throughout Saudi Arabia, the G.C.C. countries, the Middle East and the Far East. products are available directly from as well as through a vast and reliable network of local distributors.
Special products are manufactured on request.
Acoustical Ceiling PanelsTechnical Data SheetProduct Code: ACP
ENERGY SAVING ENVIRONMENTALLY FRIENDLY RECYCLED MATERIALS SOLUTION FOR GLOBAL WARMING
AFICO is committed to a greener, cleaner environment. AFICO have responded to this call for conservation by increasing the amounts of recycled materials in our products.
No maintenance is required. Acoustical Ceiling Panels have a high resistance to accidental damage from knocks and handling during installation and maintenance. Dimensionally stable under varying conditions of temperature and humidity, rot-proof, odourless, non-hygroscopic and will not sustain vermin or fungus due to its inorganic and mineral compositions.
The product will maintain its thermal properties throughout the lifetime of the construction and will not age. fibreglass is non toxic and not hazardous to health.
STORAGE
To avoid moisture in the building construction, insulation products stored outside must be kept dry. We recommend products to be always stored in covered and dry areas. is not liable for the damage resulting from inadequate utilization, loading and off loading and mishandling of its products.
WARRANTY
See manufacturer’s General Terms and Conditions of Sale. As and/or OC has no control over installation design,
installation workmanship, accessory materials, or conditions of application, and/or OC does not warrant the performance or results of any installation containing their products. This warranty disclaimer includes all implied warranties, including the warranties or merchantability and fitness for a particular purpose.
Arabian Fiberglass Insulation Company reserves the right to alter product specifications without prior notice, as part of its policy of continued development and improvement. The installation methods described in this leaflet are not compulsory. The choice of materials and methods of fixing are the decision of the specifier, consultant or contractor. For further information or advice on specification of products, contact your local sales office.
AVAILABILITY
Manufactured by Arabian Fiberglass Insulation Company, Ltd. (AFICO), member of Zamil Industrial, with headquarters and production facilities located in Dammam, Saudi Arabia, under license from and utilizing the manufacturing specifications and technology of Owens-Corning Corporation (OC), Toledo, Ohio, U.S.A.
Marketed throughout Saudi Arabia, the G.C.C. countries, the Middle East and the Far East. products are available directly from as well as through a vast and reliable network of local distributors.
Special products are manufactured on request.
Acoustical Ceiling PanelsTechnical Data SheetProduct Code: ACP
ENERGY SAVING ENVIRONMENTALLY FRIENDLY RECYCLED MATERIALS SOLUTION FOR GLOBAL WARMING
AFICO is committed to a greener, cleaner environment. AFICO have responded to this call for conservation by increasing the amounts of recycled materials in our products.
No maintenance is required. Blanket Insulation have a high resistance to accidental damage from knocks and handling during installation and maintenance. Dimensionally stable under varying conditions of temperature and humidity, rot-proof, odourless, non-hygroscopic and will not sustain vermin or fungus due to its inorganic and mineral compositions.
The product will maintain its thermal properties throughout the lifetime of the construction and will not age. fibreglass is non toxic and not hazardous to health.
STORAGE
To avoid moisture in the building construction, insulation products stored outside must be kept dry. We recommend products to be always stored in covered and dry areas. is not liable for the damage resulting from inadequate utilization, loading and off loading and mishandling of its products.
WARRANTY
See manufacturer’s General Terms and Conditions of Sale. As and/or OC has no control over installation design,
installation workmanship, accessory materials, or conditions of application, and/or OC does not warrant the performance or results of any installation containing their products. This warranty disclaimer includes all implied warranties, including the warranties or merchantability and fitness for a particular purpose.
Arabian Fiberglass Insulation Company reserves the right to alter product specifications without prior notice, as part of its policy of continued development and improvement. The installation methods described in this leaflet are not compulsory. The choice of materials and methods of fixing are the decision of the specifier, consultant or contractor. For further information or advice on specification of products, contact your local sales office.
AVAILABILITY
Manufactured by Arabian Fiberglass Insulation Company, Ltd. (AFICO), member of Zamil Industrial, with headquarters and production facilities located in Dammam, Saudi Arabia, under license from and utilizing the manufacturing specifications and technology of Owens-Corning Corporation (OC), Toledo, Ohio, U.S.A.
Marketed throughout Saudi Arabia, the G.C.C. countries, the Middle East and the Far East. products are available directly from as well as through a vast and reliable network of local distributors.
ENERGY SAVING ENVIRONMENTALLY FRIENDLY RECYCLED MATERIALS SOLUTION FOR GLOBAL WARMING
AFICO is committed to a greener, cleaner environment. AFICO have responded to this call for conservation by increasing the amounts of recycled materials in our products.
No maintenance is required. Acoustical Ceiling Panels have a high resistance to accidental damage from knocks and handling during installation and maintenance. Dimensionally stable under varying conditions of temperature and humidity, rot-proof, odourless, non-hygroscopic and will not sustain vermin or fungus due to its inorganic and mineral compositions.
The product will maintain its thermal properties throughout the lifetime of the construction and will not age. fibreglass is non toxic and not hazardous to health.
STORAGE
To avoid moisture in the building construction, insulation products stored outside must be kept dry. We recommend products to be always stored in covered and dry areas. is not liable for the damage resulting from inadequate utilization, loading and off loading and mishandling of its products.
WARRANTY
See manufacturer’s General Terms and Conditions of Sale. As and/or OC has no control over installation design,
installation workmanship, accessory materials, or conditions of application, and/or OC does not warrant the performance or results of any installation containing their products. This warranty disclaimer includes all implied warranties, including the warranties or merchantability and fitness for a particular purpose.
Arabian Fiberglass Insulation Company reserves the right to alter product specifications without prior notice, as part of its policy of continued development and improvement. The
The choice of materials and methods of fixing are the decision of the specifier, consultant or contractor. For further information or advice on specification of products, contact your local sales office.
AVAILABILITY
Manufactured by Arabian Fiberglass Insulation Company, Ltd. (AFICO), member of Zamil Industrial, with headquarters and production facilities located in Dammam, Saudi Arabia,
and technology of Owens-Corning Corporation (OC), Toledo, Ohio, U.S.A.
Marketed throughout Saudi Arabia, the G.C.C. countries, the Middle East and the Far East. products are available directly from as well as through a vast and reliable network of local distributors.
Special products are manufactured on request.
Acoustical Ceiling PanelsTechnical Data SheetProduct Code: ACP
ENERGY SAVING ENVIRONMENTALLY FRIENDLY RECYCLED MATERIALS SOLUTION FOR GLOBAL WARMING
AFICO is committed to a greener, cleaner environment. AFICO have responded to this call for conservation by increasing the amounts of recycled materials in our products.
No maintenance is required. Acoustical Ceiling Panels have a high resistance to accidental damage from knocks and handling during installation and maintenance. Dimensionally stable under varying conditions of temperature and humidity, rot-proof, odourless, non-hygroscopic and will not sustain vermin or fungus due to its inorganic and mineral compositions.
The product will maintain its thermal properties throughout the lifetime of the construction and will not age. fibreglass is non toxic and not hazardous to health.
STORAGE
To avoid moisture in the building construction, insulation products stored outside must be kept dry. We recommend products to be always stored in covered and dry areas. is not liable for the damage resulting from inadequate utilization, loading and off loading and mishandling of its products.
WARRANTY
See manufacturer’s General Terms and Conditions of Sale. As and/or OC has no control over installation design,
installation workmanship, accessory materials, or conditions of application, and/or OC does not warrant the performance or results of any installation containing their products. This warranty disclaimer includes all implied warranties, including the warranties or merchantability and fitness for a particular purpose.
Arabian Fiberglass Insulation Company reserves the right to alter product specifications without prior notice, as part of its policy of continued development and improvement. The installation methods described in this leaflet are not compulsory. The choice of materials and methods of fixing are the decision of the specifier, consultant or contractor. For further information or advice on specification of products, contact your local sales office.
AVAILABILITY
Manufactured by Arabian Fiberglass Insulation Company, Ltd. (AFICO), member of Zamil Industrial, with headquarters and production facilities located in Dammam, Saudi Arabia, under license from and utilizing the manufacturing specifications and technology of Owens-Corning Corporation (OC), Toledo, Ohio, U.S.A.
Marketed throughout Saudi Arabia, the G.C.C. countries, the Middle East and the Far East. products are available directly from as well as through a vast and reliable network of local distributors.
Special products are manufactured on request.
Acoustical Ceiling PanelsTechnical Data SheetProduct Code: ACP
Manufactured by Arabian Fiberglass Insulation Company, Ltd. member of Zamil Industrial Co. ZI, with head- quarters and production facilities located in Dammam, Saudi Arabia, under license from and utilizing the manufacturing specifications and technology of Owens-Corning Corporation OCF, Toledo, Ohio, U.S.A.
Marketed throughout Saudi Arabia, the G.C.C. countries, the Middle East and the Far East. products are available directly from as well as through a vast and reliable network of local distributors.
