32
**A MINIMUM OF TWO ADULTS ARE REQUIRED FOR ASSEMBLY** Copy
�
**A MINIMUM OF TWO ADULTS ARE REQUIRED FOR ASSEMBLY**
Copy
�INSTRUCTION #1034144
The product you just purchased could be FREE!
Register your product at www.lifetime.com and receive three important benefits:1. You automatically will be entered to win $200 in our monthly drawing!
2. In the unlikely event of a product recall or safety modification, we can notify you immediately and directly.
3. You may choose to receive Preferred Customer Announcements and promotions regarding new Lifetime products.
www.lifetime.comSave this instruction in the event that the manufacturer has to be contacted for
replacement parts.
MODEL #51563WARNING
To ensure your safety, do not attempt to assemble this system without reading and following all instructions carefully. Identify and inventory the parts using the Parts List. Failure to comply with any of the warnings in these instructions may result in serious personal injuries such as cuts, broken bones, nerve damage, paralysis, brain injury, or death. Failure to comply may also result in property damage. Please heed all warnings and cautions.
Reebok Freestanding POWER LIFT®
BASKETBALL SYSTEM
01/17/2008
**U.S. Canada and UK customers ONLY**IF ASSISTANCE IS NEEDED,
DO NOT CONTACT THE STORE!!!US and Canada customers call our customer service department at
1 (800) 225-3865HOURS: 7:00 a.m. to 5:00 p.m. Monday through Friday (Mountain Standard Time)
Call, or visit our Website for Saturday hours.UK customers call 01992 450333
**For customers outside the U.S., Canada, or UK, please contact the store for assistance.**
Copy
�
POLE SECTION IDENTIFICATIONIdentify the pole sections before beginning assembly. Failure to assemble the
pole sections correctly may result in severe personal injury or property damage as described on Page Two.
ONCE THE POLE SECTIONS HAVE BEEN SEATED, THEY CANNOT BE SEPARATED.
Note: Tapers and flares are exaggerated in the illustrations.
TP mP bP
Top Pole:Four holes at the top of the pole, four holes in the middle, four holes near the bottom and three small holes at the very bottom.
Middle Pole:One slot at the top of the pole and three small holes at the bottom. Warning Sticker.
SAFETY INSTRUCTIONS
Most injuries are caused by misuse and/or not following instructions. Use caution when using this system.
Owner must ensure that all players know and follow these rules for safe operation of the system.
To ensure safety, do not attempt to assemble this system without following the instructions carefully. Check entire box and inside all packing material for parts and/or additional instruction material. Before beginning assembly, read the instructions and identify parts using the hardware identifier and parts list in this document. Proper and complete assembly, use and supervision are essential for proper orientation and to reduce the risk of accident or injury. A high probability of serious injury exists if this system is not installed, maintained, and operated properly.
FAILURE TO FOLLOW THESE WARNINGS MAY RESULT IN SERIOUS INJURY OR PROPERTY DAMAGE AND WILL VOID WARRANTY.
• If using a ladder during assembly, use extreme caution.• Two capable adults are recommended for this operation.• Check base daily for leakage. Leaks will cause system to fall.• Assemble the pole sections properly. Failure to do so could cause the pole
sections to separate during play or transport.• Minimum operational height is 7’6” (2.23m) to the rim.
Bottom Pole: One slot at the top of the pole and four holes at the bottom.
AN
AP
Top Pole Brace: �” pole. One hole at the top of the pole and one small hole at the bottom.
Bottom Pole Brace: �” pole. One slot at the top of the pole and one hole at the bottom.
�
PARTS LISTID Part # Description Qty TP �0�069� �.5” Top Pole � mP �0�07�� �.5” middle Pole � bP �0�0690 �.5” bottom Pole � Lb �0�076� Left backboard bracket � Rb �0�078� Right backboard bracket � AA �005�9� Revolution base � Ab 5�00�5 �/�” x �� �/�” Axle � AC �005�80 Wheel � AD 8�5608 Rim � AE �0�07�� backboard � FS�6�00 Warning Sticker (Applied) � AF �0�0669 Short Extension Arm � AG �0�0667 Long Extension Arm � AH HA0�800 Gas Spring � AI �0�0758 Rear Lifter Arm � AJ 50�0�7H Adjustment Handle � AK 50�0�9G Trigger � FC Cb08999 Corner Frame Pad � Fb �0008�� bottom Frame Pad � AL 60�08� Height Sticker � Am ZA�0�85 bellows � AN �0�069� �” Upper Pole brace � AP �0�069� �” Lower Pole brace � AQ �0�069� Angle Adapter � AS �005�90 Revolution Shield � Revolution Shield Hardware (1006981)SA �0�0�� 5/�6” Flat Washer �� Sb �00�60� 5/�6” x � �/�” Pan Head Screw 6 SC �00095 5/�6” Cap Nut 6 SD bS0�000 �/�” x �/�” Screw � SE �005�0� �” Pole brace Cap � Rim Hardware (1012738)RA �00066 5/�6” Hex T-Nut � RC �0�0�� 5/�6” Flat Washer � RD �0�056 7/�6” Rubber Washer � RE �0�065 5/�6” x � �/�” Tap bolt � RF �009�00 �.5 “U-bolt � RG �0�090 5/�6” Nylock Flange Nut � RH �00���7 Compression Spring � RI 80�0�� Spring Retainer Plate � RK �00��8 5/�6” Jam Nut � Handle Hardware (1017923)TA �00�0� Release Pin � Tb �0�007 �/8” x 6 �/�” Hex bolt � TC �00�87 �/�” x 6 �/�” Hex bolt � mG �0�008 �/�” Centerlock Nut � mH �0�008 �/8” Centerlock Nut �
Tb
5
SD
RA RE
RG
RI
(Not actual size)
HARDWARE IS ACTUAL SIZE(Unless otherwise indicated)
Tools and materials Required for Assembly(Not Included)
�. Adjustable Wrench�. 7/�6” Wrenches (�)�. �/�” Wrenches (�) �. 9/�6” Wrenches (�) 5. �/�” Wrenches (�) 6. Hammer or mallet7. 500 lbs. Sand or Water Supply
8. Tape measure9. Scrap Wood/ Cardboard�0. Phillips Screwdriver��. Electric Drill��. Scissors/Wire Cutters��. Pliers��. Funnel
**A MINIMUM OF TWO ADULTS ARE REQUIRED FOR ASSEMBLY**
RC RD
RK
SA
Sb
SC
TA
TC
mH
6
mN
(Not actual size)
mF
mL
(Not actual size)
mQ
ID Part # Description Qty Revolution Hardware (1006982)mA �006��� �/�” x �” Hex bolt � mC E�00�7 �/�” x � �/�” bolt � mD bA0�800 �/�” x .69” Plastic Spacer � mE �000�9 �/�” x 7 �/8” Hex bolt 5 mF �000�� Cotter Pin � mL �00055 � �/�” metal Pin � mT 800��� �/�” x � �/�” Spacer � mV 5000�5 �/8” x �/�” Plastic Spacer � mP 800��9 �/�” x � 7/�6” Spacer � mJ �0�05� �/8” x �” Hex bolt � mQ �000�� �/8” Flat Washer � SD bS0�000 �/�” x �/�” Screw � mG �0�008 �/�” Centerlock Nut 7 mN 5000�� �/�” x �/8” black Spacer 8 mW �0055�6 �/�” x 8 �/�” Hex bolt � mO 50008� Grease Packet � mY �00�6�0 Self-Tapping Screw � mZ �0089�8 �/�” star tooth washer � Backboard Hardware (1030724)bA �0�0�� 5/�6” x � �/�” Carriage bolt � bb �000�� �/�” Centerlock Nut � bC �0007� �/� Flat Steel Washer � RG �0�090 5/�6” Nylock Flange Nut � AW 500096 �.5” Pole Cap � bD DD00800 Net � bG 800��� �/�” x � 5/�6” Spacer � AY 50�056 Plastic Guard � AZ CA00885 Zip Tie � AR �0�0660 Spring bracket � Frame Pad Hardware (HH00700)FA bS00�00 #�0 x 7/8” Self-Drilling Screw �0
PARTS LIST
mG
mY
mZ
bb
mT
7
mJ
mP
bA
mE
FA
mAmC
mD
mV
mW
8 1/2”
bC
bG
8
HARDWARE IS ACTUAL SIZE(Unless otherwise indicated)
ID Part # Description Qty
PARTS LISTBase Hardware (1006980)HA �0059�9 �/�” Washer � Hb bb0��00 �/�” x � �/�” Hex bolt � HC bN0��00 �/�” Nylock Nut � HD �0055�� �/8” x � �/�” Hex bolt � HE �006��� �/8” Flat Washer � mH �0�008 �/8” Centerlock Nut � HF �0076�� Clevis � HG bD00�00 �/�” x 7” Axle � HH CF00�99 � �/�” T-Plug � HI �007800 �” bottom Pole Plug � mb �006��8 �/�” x � �/�” Spacer �
Hb HA HC
HD
HE HF
(Not actual size)(Not actual size)
HH
mb
9
� Align the hole in a Top Pole Brace (AN) with the slot in a Bottom Pole Brace (AP) and slide the Top Pole over
the Bottom Pole. Do not jam the poles together until instructed.
The Screw will spin freely once installed.
Insert a 1/4” x 3/4” Screw (SD) in the small hole in the Top
Pole Brace (AN) and into the slot of the Bottom Pole Brace
(AP).
AN
AP
� This step cannot be reversed. In order to seat the poles, strike each end of the pole very hard 5 to 6 times on a piece of scrap wood or cardboard. This must be done even if the poles cover the slots before
seating.If the Top Pole Brace does not completely cover the slots on the Bottom Pole Brace after seating,
DO NOT COMPLETE ASSEMBLY. Call our Customer Service Department.
Do not hit your feet with the pole sections, as serious injury could occur.
WARNING
Required For This Page:Screwdriver
�00698�
Complete Steps 1 & 2 for Both sets of Pole Braces.
SD(�)
AN
AP
The poles must be seated together!! Even if the poles cover the slots before seating, you must strike them hard on the wood five to six times!! Failure to seat the poles correctly could allow the poles to separate during use, which could lead to serious personal injuries or property damage as listed on Page Two.
SD
�0
� Insert Pole Caps (SE) into Brace poles. Lay the Assembled Brace poles side by side with the holes facing upward and the Pole Joint
Screws facing inward toward each other.
� Insert the 21 3/4 Axle (AB) through the top holes of both Brace Poles to hold them in position.
5 Rest the Shield (AS) on top of the poles and move poles until the holes in the Shield line up with the holes in the Brace Poles.
Pole Joint Screws must face toward
each other. The slots in the poles
will be on top.
SE SE
AS
AB
��
6 Start with the middle hole on each side and insert a 5/16” x 2 1/2” Pan Head Screw (SB) through a 5/16” Flat Washer (SA), the hole in the pole, and another 5/16” Flat Washer. Secure underneath a
5/16” Cap Nut (SC).
7 Repeat step six for each of the remaining holes.
SA
Sb
Required For This Page: �00698�
(6)
(��)ScrewdriverSC(6)
SB
SA
SASC
SB
SA
SASC
�/�” Wrenches
WARNINGDo not overtighten the Cap Nut. If the end of the Bolt breaks through the plastic cap, call our Customer Service Department at the number on Page Two. Exposed threads on the end of the Bolt may cause serious injuries such as those listed on Page Two.
��
9
Note: The longer side of the clevis is
on top.
�� Remove the 21 3/4 Axle (AB) from the top of the poles. Set the brace poles aside until later in the assembly.
Required For This Page:9/�6” WrenchesScrewdriver
Lay the Pole Braces flat on ground with the Shield side up. Slide a Clevis (HF) and bolt into the bottom of each Pole brace, with the longer side of the Clevis facing up.
8 Insert a 1/2” x 1 1/4” Hex Bolt (HB) through a Clevis (HF). Repeat for other Clevis.
�006980
Hb (�)
HF HB
HF
�0 Slide a 3/8” x 2 1/2” Hex Bolt (HD) through a 3/8” Washer,
a Pole Brace (AP) and a Clevis (HF), and another 3/8” Washer. Secure with a 3/8”
Centerlock Nut (MH).HD
MH
HD (�)
mH (�)HE(�)
HE
HE
APAP
AB
HF (Not actual size)(�)
��
Apply the Height Sticker (AL) so it wraps around the opposite side of
the pole as the Spring Bracket (AR).
The small notch in the Sticker fits around the hole in the pole.
AR AL
TP
��
MJ MP AR
MH
Small holes
Large holes
Tighten all hardware securely.
MQ
TP
��
mQ
mJ
mP
mH
�00698�
(�) (�)
(�)
SD
(�)
(�)
Required For This Page:
9/�6” WrenchesScrewdriver
�� Align the hole in the Top Pole (TP) with the slot in the Middle Pole (MP) and slide the Top Pole over the
Middle Pole. Do not jam the poles together until instructed.
The Screw will spin freely once installed.
SD
TP
MP
Note: There are three screw holes at the bottom of the pole. The correct hole will be slightly larger and
slightly higher up on the pole than the others.
�006980
Insert a 1/4” x 3/4” Screw (SD) through the small hole in the
Top Pole (TP) and into the slot of the Bottom Pole (BP).
MH
��
�5
MP
BPSD
Align the hole in the Middle Pole (MP) with the slot in the Bottom Pole (BP) and slide the Middle Pole
over the Bottom Pole. Do not jam the poles together until instructed.
The Screw will spin freely once installed.
Note: There are three screw holes at the bottom of the pole. The correct hole will be slightly larger and
slightly higher up on the pole than the others.
SD(�)
�00698�Required For This Page:
Screwdriver
�6 This step cannot be reversed. BP
MP
TP
In order to seat the poles, strike each end of the pole very hard 5 to 6 times on a piece of scrap wood or cardboard. This must be done
even if the poles cover the slots before seating.
If the Top and Middle Poles do not completely cover the slots on the Middle and Bottom Poles after seating, DO NOT COMPLETE ASSEMBLY. Call our Customer Service
Department.
Do not hit your feet with the pole sections, as serious injury could occur.
WARNINGThe poles must be seated together!! Even if the poles cover the slots before seating, you must strike them hard on the wood five to six times!! Failure to seat the poles correctly could allow the poles to separate during use, which could lead to serious personal injuries or property damage as listed on Page Two.
Insert a 1/4” x 3/4” Screw (SD) through the small hole in the
Top Pole (TP) and into the slot of the Bottom Pole (BP).
�5
�9 �0 Lift the front of the base and fit the wheels and axle into the groove in the bottom of the base. Step down onto the base until the axle
snaps into place.
Required For This Page:mY(�)�00698�
Electric Drill
�8
�7Use an electric Drill to insert two self-tapping screws
(MY) through a 1/4” Star Washer (MZ) and into the pole at the positions shown.
MY
Insert the Pole Cap (AW) into the the pole.
AW
Slide a wheel onto each end of a 21 3/4
Axle (AB)
MY
AC
AC
AB
AA
mZ(�)
MY
SD
BP
MP
TP
MZ MZ
Chuck the Screw directly into your Electric Drill.
�6
�� Slide the 21 3/4 Axle (AB) through the bottom hole in the pole, the Pole Plug (HI), the other side of the pole.
��
�� Slide the pole into the notch in the base and fit the 21 3/4 Axle (AB) into the groove at the bottom of the base. Slide the 7” Axle
(HG) into the pole and rotate the pole up into place until it fits into the groove at the top of the base.
Slide the bolt at the bottom of the Brace poles through the holes at the front corner of the base. Secure underneath with a 1/2” Nylock
Nut (HC) and 1/2” Washer (HA).
AB
HI
AB
HB
HCHA
Required For This Page:
�006980�/�” Wrenches HA
HC(�)
(�)
Note: Spring Bracket (on Top Pole) should face toward back of
the base.HG
�7
AH
AM
AH
AM
Zip Tie (AZ)
Larger End
Use pliers to tighten the Zip Ties (AZ) securely. Cut off the ends of the Zip Ties.
Zip Tie (AZ)
The bottom of the Bellows (AM) overlaps the Gas Spring (AH) by 1”. The top is 1/2”
from the top of the Spring.
�5
Required For This Page:
mW
mN
(�)
(�)
�00698�
�/�” Wrenches
8 1/2”
(Not actual length)
Pliers
Attach the top of the Brace poles to the pole��
MW
MN MN
MG
mG(�)
ANAN
�8
TC
mG
(�)
(�)
6 1/2”
(�)*
(�)*
Pliers
�7
MF
ML
AR
MF ML
AM
TPUse pliers to bend the Cotter Pin (MF) as shown above.
*(Not actual size)
mF
mL
9/�6” Wrenches
Required For This Page:
�0�79��
MG
TC
AJ
Tighten the Nut until it is flush with the Bolt.
AIAH AI�6 Align the Rear Lifter Arms (AI) with the Gas Spring (AH).
AI
�00698�
�9
�00698�
�8
TA
�9
AQ
�0The Release Pin (TA) should fit into
the channels in the Trigger (AK).
TA
TB
MH
AJ
MV
Tighten the Nut until it is flush with the
Bolt.
TP
9/�6” WrenchesRequired For This Page:
6 1/2”
(Not actual length)
�0�79��TA (�)
MH
��
TB
AK
AP
Tighten the Nut until it is flush with the Bolt.
Tb (�)
mH(�)
mV(�)
�0
����RB
LB
RF
Make sure the U-Bolt (RF) is in
the notches.
Hold the Backboard Brackets (LB & RB)
together.
�/�” Wrench
bG (�)
7/�6” Wrench
Required For Steps 32-34:
(�)�0�07��
(�)
RERC
RD
(�) (�)
(�)
RA
�0��7�8
(�)
bb
mA
MAMA
MC RFBC
MB
BB
RBLB
MG
�00698�
mC (�)mG(�)
bC(�)
AQ
AQ
Attach the Angle Brackets (AQ) to the Backboard Brackets (LB & RB).
BG
mb(�)
�/�” Wrench
MA
MC BC
BC
�006980
��
RARE RC RDThe Tap Bolts (RE) should
be at the outer edge of
the holes.
Tighten the T-Nuts (RA) only until the Rubber Washers (RD)
begin to bulge.
RDRD
�� AD
�/�” WrenchesRequired For Steps 35-37:
�0��7�8RK
RG (�)RI (�)
(�)
(Not actual size)
RG
AY
RK
�6
Tightening these Nuts (RG) will adjust the Rim tension.
Place the Plastic Guard (AY) on the back of the
Rim.
Tighten the Jam Nuts (RK) onto the U-Bolt as far as
they will go.Only hand
tighten the Nylock
Flange Nuts (RG).
RK
RHRI
RG
�7
Only hand tighten the Nylock Flange
Nuts (RG).
AD
�5RF
AE
��
�8 BA BA
BA
�9 Bend the Backboard Brackets (LB & RB) out.
LB
Slide a Carriage Bolt (BA) into the crimped slot in each Backboard channel.
RGRG
RB
Completely tighten all Rim hardware.
Do not overtighten the Nuts (RG).
Required For This Page:
The lower holes should go over the Carriage Bolts.
bARG(�) (�)
�0�07��
�/�” Wrenches
��
�0
FC
Remove the plastic film from the Backboard.
The lip of the Frame Pad overlaps the front
of the Backboard.
FA
FAUse an
electric drill to insert the
Screws. FC
Attach the Bottom Frame Pad first. Align the small line in the back of the Bottom Frame Pad
with the seam in the Backboard frame.
FC
FB
Required For This Page:
�00698�
�/�” WrenchesHH00700
FAElectric Drill(8)
mE(�)
mGmD (�)(�)
7 1/8”
(Not actual length)
MG
AF
��Tighten the Nut until it is flush with the Bolt.
MD
AFME
AF
��
�/�” Wrenches
mE(�)
�00698�
mD (�)(�)
Required For This Page:
7 1/8”
(Not actual length)
��
The Backboard and Rim must rest on cardboard to prevent scratching.
MG
��
Attach this end of the Long Extension Arms (AG) to the Backboard Brackets
MD
MEAGAG
MD
AG
Tighten the Nut until it is flush with the Bolt.
mG
�5
mT
(�)
(�)
��
ME
AG
The Rear Lifter Arms must be on the inside of the Extension Arms.
Only finger tighten the Nut.
Lift the pole up until the Long Extension Arms (AG) line up with the Rear Lifter Arms (AI).
AG
(�)
7 1/8”
(Not actual length)
�/�” Wrenches
�00698�
Required For This Page:
MT
AG MG
AI
AI
There must be a 1/2” x 1/8” Spacer (MN) between each Long Extension Arm (AG) and the pole.�5
AO
ME MG
MN
Only finger tighten the Nut.
AG AG
AM
mG(�)
mN
mE
�6
MN
MGME
AF AF
�6 There must be a 1/2” x 1/8” Spacer (MN) between each Short Extension Arm (AF) and the pole.
Completely tighten the Nuts from steps 31 through 33.
(�)
mE(�)
7 1/8”
(Not actual length)
�/�” Wrenches
�00698�
Required For This Page:
Before standing up the system, attach the Net (BD).
Please call our Customer Service Department at the number on Page
Two to obtain replacement Nets. Our Nets are shorter than average to
reduce the risk of entanglement.
�7 �8 Apply Grease (MO) to these areas.
BD
mG(�)
AD
mN
�7
Never put the system in an upright position without proper weight in the Base. The system may fall over and could result in serious personal injury or property damage.
WARNING
�9
�9
1. Make sure the surface beneath the Base is smooth and free of stones, gravel or other sharp objects that could puncture the Base and cause leakage.
2. Check the Base frequently for cracks or punctures. 3. Always check the water level before play. If a leak is found or the water level is low, lay
the system down on the ground and call the Customer Service number for assistance.4. If the unit is to be stored without weight, tilt the unit forward and rest the Rim on the
ground.5. Each time the Base is filled with water, add one tablespoon of chlorine bleach to the water
to prevent algae formation inside the Base.
WHEN USING WATER IN THE BASE TAKE THE FOLLOWING PRECAUTIONS:
Filling the base with Water
Check the Base for leaks frequently.
If a leak develops, water could run out unnoticed, allowing the unit to fall over and result in serious personal injuries or property damage. Check the Base carefully for leaks.
Insert the Base Plugs (LK) into the two fill holes on top of the base.
Filling the base with SandLift top of the system off of the ground, and have one person hold the pole, while a second person fills the
base half-way with sand.
Insert the Base Plugs (LK) into the two fill holes on top of the base.
While still holding the pole, stand the system upright and fill the base the remainder of the way.
For safety reasons, we recommend that sand be used instead of water to fill the Base.
WARNING
Lift the top of the system off of the ground, and have one person hold the pole, while a second person fills the base half-way with water.
While still holding the pole, stand the system upright and fill the base the remainder of the way.
�8
Operation of the height adjustment system
WHILE TRANSPORTING THE PORTABLE SYSTEM, USE CAUTION TO PREVENT THE MECHANISM
FROM ADJUSTING.
The adjustable system may be adjusted from 7 1/2 feet to 10 feet.Hold the Handle tightly and squeeze the Trigger to engage the Gas Spring. Raise the Handle to lower the Backboard, or lower the Handle to raise the Backboard.
moving the system
WARNING: The system must only be moved by people capable of handling its weight. Children should not be allowed to move the system.
1. Adjust basketball system to lowest position.2. Approach the system from the front. 3. Grab the Top Pole Braces (just above the Shield) and pull the system
towards you until the system rests on its wheels.4. After moving system, slowly tip it back into an upright position.
Two adults are required to move this system.
50 Rest a Carpenters Level on the rim, perpendicular to the backboard. Loosen the
nut and slide the 1/4” x 3” Hex Bolt (MA) along the
Adjustment slot until the rim is level.
Loosen these nuts and adjust the angle until the rim is level.
Re-tighen all nuts.
�9
The life of your basketball system depends on many variables. The climate, exposure to corrosives such as salt, pesticides, or herbicides, and excessive use or misuse can all contribute to pole failure, which may cause property damage or personal injury.
Check your basketball system frequently for loose hardware, excessive wear, and signs of corrosion. For safety reasons, and to prolong the life of your basketball system, you must take the following preventive measures.
a. Check all Nuts and Bolts. If any are loose, tighten them.b. Check all parts for excessive wear and tear. If necessary, replace any parts that have been
worn or damaged through usage. Check the Pole Cap for cracks or tears that could let water into the pole. Contact our Customer Service Department for replacement parts.
c. Inspect the Warning Sticker on the pole. If it is ripped, faded, or illegible, call our Customer Service Department to request a replacement Sticker.
d. Check all pole sections for visible rust or chipped or cracked paint. If either are present, do the following:
1. Use an emery cloth to completely remove any rust or chipped paint. 2. Clean the area with a damp cloth and allow it to dry. 3. Apply two coats of a rust preventative, high gloss enamel paint to the area. Allow
the paint to dry between coats.IFRUSTHASPENETRATEDTHROUGHTHEPOLEANYWHERE,
REPLACEITIMMEDIATELY!
POLE CARE AND SYSTEm mAINTENANCE
Windex1
Joy2 Mr. Clean2
Fantastik3
Formula 4094
Only clean the Backboard with the approved cleaning materials listed below:
The use of other chemicals will void the warranty.1Registered Trademark of the Drackett Products Company.2Registered Trademarks of Procter & Gamble.3Registered Trademark of Texize, Division of Norton Norwich Products Inc.4Registered Trademark of the Clorox Company.
�0
This page intentionally left blank.
��
FAUTE DE NE PAS SUIVRE CES AVERTISSEMENTS, VOUS RISQUEZ DE CAUSER DES BLESSURES GRAVES ET/OU
DES DOMMAGES À L’ÉQUIPEMENT.
SI NO SE OBEDECEN ESTAS ADVERTENCIAS PUEDENPRODUCIRSE GRAVES LESIONES y/O DAñOS A LA
PROPIEDAD.Le propriétaire doit s’assurer que tous les joueurs connaissent et appliquent les règles suivantes afin d’utiliser l’équipement en
toute sécurité.
WARNING
El propietario del sistema debe asegurarse de que todos los jugadores conozcan y respeten estas reglas para que el
sistema se use en forma segura.
FAILURE TO FOLLOW THESE WARNINGS MAy RESULT IN SERIOUS INJURy AND/OR PROPERTy DAMAGE.
Owners must ensure that all players know and follow these rules for safe operation of the system.
Only hang from the rim briefly to regain balance or avoid injuring others. Release the rim as soon as safely possible.During play, especially when performing dunk type activities, keep
player’s face away from the backboard, rim, and net. Serious injury could occur if teeth/face come in contact with the backboard, rim, or net. Player should wear a mouth guard during play.Do not slide, climb, or play on base or pole.Completely fill base according to manufacturer’s instructions.
Never leave the unit standing in an upright position without first filling the base with weight or the system will tip quickly causing serious personal injury.When adjusting height or moving system, keep hands and fingers
away from moving parts.Do not allow children to move or adjust system.Do not wear jewelry (rings, watches, necklaces, etc.) during play.
Objects may entangle in net.Keep organic material away from pole base. Grass, litter, etc. could
cause corrosion and/or deterioration.
• Cuélguese del aro sólo en forma breve, para recuperar el equilibrio o evitar lesionar a otros jugadores. Suéltese del aro lo más pronto que pueda hacerlo con seguridad.• Durante el juego, especialmente al embocar violentamente de alto, la cara de los jugadores debe mantenerse alejada del tablero, el aro y la red. Pueden producirse lesiones graves si los dientes o la cara entran en contacto con el tablero, el aro o la red. Los jugadores deben usar un protector bucal durante el juego.• No se deslice, no trepe ni juegue sobre la base o el poste.• Llene la base completamente siguiendo las instrucciones del fabricante. Nunca deje la unidad en posición de uso sin haber llenado previamente la base con material de contrapeso, pues el sistema podría tumbarse rápidamente y causar graves lesiones personales.• Mantenga las manos y los dedos alejados de las piezas movibles cuando regule la altura o desplace el sistema.• No deje que los niños regulen ni desplacen el sistema.• No use joyas (anillos, relojes, collares o gargantillas, etc.) durante el juego. Estos objetos pueden engancharse en la red.• La superficie donde se coloque la base debe estar lisa y desprovista de piedras, grava u otros objetos. Las perforaciones pueden originar pérdidas, y éstas pueden hacer que el sistema se tumbe.• No permita que la base del poste entre en contacto con materiales orgánicos. El pasto, los desechos animales, etc., pueden causar corrosión y/o deterioros. • Controle el poste y todas las piezas metálicas una vez al mes en busca de signos visibles de corrosión (oxidación, picaduras, escamado). Elimine todo rastro de óxido y vuelva a pintar con esmalte para exteriores. Si el óxido ha penetrado cualquier pieza de acero, reemplace esa pieza de inmediato.• Inspeccione el sistema antes de cada uso para verificar que esté adecuadamente contrapesado, que los elementos de fijación no estén flojos, que no haya desgaste excesivo, inestabilidad ni signos de corrosión. Si encuentra irregularidades, repárelas antes de usar el sistema. Nunca juegue con un equipo dañado.• No use el sistema en presencia de vientos fuertes o condiciones climáticas adversas, ya que puede tumbarse. Coloque la unidad en su posición de almacenamiento y/o en una zona a resguardo del viento, lejos de propiedades personales que puedan dañarse si el sistema se cae, y de líneas de suministro de energía.• No use el sistema para levantar ningún objeto. El mecanismo está diseñado para elevar solamente el peso del tablero con el aro. No cuelgue nada de la agarradera, el aro, el tablero ni los brazos de elevación, ya que esto puede dañar el sistema y anular la garantía.
• Ne vous suspendez pas à l’anneau plus que nécessaire pour retrouver votre équilibre ou éviter de blesser les autres joueurs. Relâchez l’anneau aussitôt que possible.• Lors d’un match, particulièrement dans le cas des smashs, le visage du joueur ne doit pas faire face au panneau, à l’anneau, ni au filet. Le joueur risque de graves blessures si ses dents ou son visage entrent en contact avec le panneau, l’anneau, ou le filet. Les joueurs doivent toujours porter un protège-dents lorsqu’ils jouent.• Ne glissez pas, ne grimpez pas, et ne jouez pas sur la base ou le poteau.• Remplissez complètement la base selon les instructions du fabricant. Ne laissez jamais l’unité debout de plein pied sans avoir d’abord rempli la base avec un poids ou l’équipement pourrait basculer rapidement et causer de graves blessures.• Lorsque vous ajustez la hauteur ou lorsque vous déplacez l’équipement, gardez vos mains et doigts loin des pièces mobiles.• Ne permettez pas aux enfants de déplacer ou d’ajuster l’équipement.• Ne portez pas de bijoux (bagues, montres, colliers, etc.) lorsque vous jouez. Ces objets pourraient s’accrocher au filet.• La surface sur laquelle est posée la base doit être lisse et sans gravier ou tout autre objet qui pourrait trouer la base entraînant ainsi une fuite ce qui pourrait faire basculer l’équipement.• La base ne doit pas non plus être posée sur aucun type de matière organique. L’herbe, les déchets, etc. peuvent entraîner la corrosion et la détérioration de l’équipement.• Une fois par mois, vérifiez que le Poteau et toutes les pièces en métal ne montrent pas de signes de corrosion (rouille, piqûres, écaillage). Enlevez toute la rouille et repeignez complètement avec une peinture pour extérieur. Si la rouille a pénétré une des pièces en acier, vous devrez remplacer immédiatement la pièce en question.• A chaque fois que vous allez utiliser l’équipement, vérifiez d’abord l’équilibre, la possibilité de pièces desserrées ou usées, la stabilité de l’équipement et tout signe de corrosion ou réparation nécessaire avant utilisation.• Ne jouez jamais avec un équipement endommagé.• N’utilisez pas l’équipement lors de fortes rafales de vent ou de mauvais temps. L’équipement pourrait basculer. Placez l’équipement dans un endroit abrité du vent ou loin des structures qu’il pourrait endommager s’il basculait et loin des fils électriques.• N’utilisez pas l’équipement pour lever ou soulever quoique ce soit. Son mécanisme a été conçu uniquement pour soutenir le poids du panneau et de l’anneau. N’accrochez rien au manche, à l’anneau, au panneau ni aux leviers sous peine d’endommager l’équipement et d’annuler la garantie.
ADVERTENCIA AVERTISSEMENT
#FS16400 10/12/2004 www.lifetime.com
Surface beneath the base must be smooth and free of gravel or other objects. Punctures cause leakage and could cause system to tip over.Once a month check pole and all metal parts for signs of corrosion
(rust, pitting, chipping). Completely remove rust and repaint with exterior enamel. If rust has penetrated any steel part, replace that part immediately.Check system before each use for proper ballast, loose hardware,
excessive wear, instability, and signs of corrosion and repair before use. Never play on damaged equipment.Do not use system during windy or severe weather. System may
tip over. Place system in an area protected from the wind or in an area away from property that may be damaged if the system falls, and from overhead power lines. Do not use the system to lift or hoist anything. The mechanism is
designed to lift only the weight of the backboard and rim. Do not hang anything from the handle, rim backboard, or lifter arms as this will damage the system and void the warranty.
��
LIFETIME BASKETBALL EQUIPMENT5-YEAR LIMITED FACTORY WARRANTY
THE MANUFACTURER RESERVES THE RIGHT TO MAKE SUBSTITUTIONS TO WARRANTY CLAIMS IF PARTS ARE UNAVAILABLE OR OBSOLETE.
1. Lifetime basketball systems are warranted to the original purchaser to be free from defects in material or workmanship for a period of five years from the date of original retail purchase. The word “defects” is defined as imperfections that impair the use of the product. Defects resulting from misuse, abuse or negligence will void this warranty. This warranty does not cover defects due to improper installation, alteration or accident. This warranty does not cover damage caused by vandalism, rusting, “acts of nature” or any other event beyond the control of the manufacturer.
2. This warranty is nontransferable and is expressly limited to the repair or replacement of defective basketball equipment. If the equipment is defective within the terms of this warranty, Lifetime Products, Inc. will repair or replace defective parts at no cost to the purchaser. Shipping charges to and from the factory are not covered and are the responsibility of the purchaser. Labor charges and related expenses for removal, installation or replacement of the basketball system or its components are not covered under this warranty.
3. This warranty does not cover scratching or scuffing of the product that may result from normal usage. In addition, defects resulting from intentional damage, negligence, unreasonable use or hanging from the net or rim will void this warranty.
4. Liability for incidental or consequential damages is excluded to the extent permitted by law. While every attempt is made to embody the highest degree of safety in all equipment, freedom from injury cannot be guaranteed. The user assumes all risk of injury resulting from the use of this product. All merchandise is sold on this condition, and no representative of the company may waive or change this policy.
5. This product is not intended for institutional or commercial use; Lifetime Products, Inc. does not assume any liability for such use. Institutional or commercial use will void the warranty.
6. This warranty is expressly in lieu of all other warranties, expressed or implied, including warranties of merchantability or fitness for use. Neither Lifetime Products, Inc., nor any representative assumes any other liability in connection with this product.
ALL WARRANTY CLAIMS MUST BE ACCOMPANIED BY A SALES RECEIPT.
To register the product, visit our website at www.lifetime.com
REPORT PRODUCT DEFECTS IN WRITING TO:Lifetime Products, Inc., PO Box 160010 Clearfield, UT 84016-0010 or
call (800) 225-3865 M-F 8 a.m. to 5 p.m. MST.Please include your dated sales receipt and photographs of damaged parts.
