A Self-Contained, mobile distribution unit. The perfect solution for your asphalt maintenance needs.
No dedicated truck necessary, simply load onto a truck of your choice and in minutes:
You’re ready to go!
When not in use, the RaynMaker stores
Flat on any level surface.
Presenting: The
Skid-Mounted & Totally Self-Contained:
No Hydraulics to hook up
No Hoses to hook up
No Electrics to hook up
No PTO required
Easy On - Easy Off, stores flat
Wireless Controls:
Operate From the Truck
Or up to 1,500 feet away!
Use one of your existing fleet:
Flatbed or Dump Truck
Reduces Fleet inventory
No registration, no smog
Totally self-contained, the RaynMaker has its own die-
sel engine, storage tank, hydraulics, digital controls,
material spread rate computer, pumping system, mate-
rial filters and spray bar.
Stores flat on any level surface when not in use.
The RaynMaker begins with a full sweep helical mixing system, necessary to assure proper suspension
of fine aggregates in the chosen emulsion mix. The mixer is driven hydraulically through a direct drive
system, no chains or sprockets to beak and no chain guards to worry about.
Storage Configuration: Tank sizes vary according to customers needs, from 1,000 gallons to 4,000 gal-
lons. Standard configuration is 1,500 gallons. Tanks are built with ASTM A572 T-1 Hi-Tensile Steel.
Each tank unit is independently framed and mounted on a master sub-frame with an engineered
gradient to encourage material flow to the delivery point.
Engine/Tank Options: The RaynMaker is available with multiple engine choices, single or dual
pumps, various electronic accessories and a variety of sizes of hydraulically driven, full sweep mixer
storage tanks. The RaynMaker may be purchased with or without a storage tank.
SMART-OPS: Digital Smart-Ops Control System with GPS -
monitors your material flow.
Smart-Ops is a computer monitoring/control system that resides inside
the operator control station. Smart-Ops consists of a Sauer-Danfoss
MC24 micro controller with a DP200 monochrome display.
Smart-Ops allows the operator to adjust the material spread rate, in
accordance with calibrations. Once set, remote operations are then
controlled by the Smart-Ops remote unit which may be operated from
the cab of the truck or from anywhere within 1,500 feet.
Using GPS speed sensing, Smart-Ops will assist in maintaining a
constant delivery rate of material per square yard of surface, even
while actual forward delivery speed may vary. The speed information
allows the computer to adjust the product output to the predetermined
spread rate. We use GPS so the RaynMaker can be easily and quickly
installed on the vehicle of choice.
The GPS unit has an onboard battery for retaining the latest position-
ing data, providing quick start up of the system. The GPS is an over the horizon version that
uses four satellites to gather its positioning, this helps prevent dead spots from trees.
The Smart-Ops System is designed to be rugged and simple. Full operating instructions
are provided with every RaynMaker in printed form and on CD. As always, our
technical support staff are trained and ready to provide any assistance required.
MATERIAL FLOW SYSTEM
Controlled from the Smart-Ops Remote, the RaynMaker uses a
positive displacement Bowie pump regulated by the Smart-Ops
system. Engineered modifications allow this system to handle fine
aggregate filled materials and the toughest of challenges.
The RaynMaker material system is also equipped for self loading
of material into the storage tank by reversing the delivery pump.
Quick coupling connections make hook up to your supply source
easy.
Hydraulic System: Hydraulics are used to drive the material ump,
the spray bar nozzle control and to raise and lower the spray bar.
The RaynMaker uses only the highest quality piston pumps and
orbital motors made by Sauer-Danfoss. Piston pumps offer higher
pressure capabilities, longer life, quieter operations, pressure
compensating options and lower operating costs.
The RaynMaker has a 20 Gallon Hydraulic Reservoir, a separate
thermostatically controlled hydraulic oil cooler and features auto-
matic pressure compensation allowing the system to adjust volume
to maintain a pressure setting.
Material Filtration: With the introduction of high performance
fine aggregate filled emulsion systems, filtration becomes an
important factor. Oversize stone or other particles can easily clog
a spray system.
The RaynMaker easily handles those challenges with two separate
filtration systems. The primary system has 339 square inches of
3/8” filter face. The secondary system has 1,620Square Inches of
1/8” filter face. All filters are easily removable for service and
may be back-flushed in place by use of a water hose.
The RaynMaker Spreader Bar Assembly: The spreader bar con-
sists of an 8’ primary bar which incorporates two large filters and
is equipped with 6 spray tips. Standard configuration will spray up
to 10 feet in width while additional widths to 14 feet may be ac-
complished using included snap in extensions.
The RaynMaker spray bar is mounted on a retractable lift system
that is hydraulically operated. This allows the bar to be locked in a
raised position for travel and storage and allows the whole
RaynMaker unit to be stored on any flat surface.
Once the spreader bar lowered in place, the RaynMaker offers an
optional hydraulic height adjustment feature. This allows the oper-
ator to further adjust the spreader bar height up or down over a
range of 8” to fine tune the spray height for proper material fan
width.
Spray tips are removable for service and a selection of tips are
available for a wide range of materials and applications.
Using a range of new materials becoming available, the RaynMaker is your tool for protective applications on a variety of pavements. The following examples of aggregate filled sealcoat projects demonstrate the wide variety of uses for the versatile RaynMaker.
Residential Roadways
Rural Roadways
Chip Seal Roadways
Chip Sealed Roadways now have a partner in
the pavement maintenance family.
By surrounding each chip with a new coating of
asphalt and crushed aggregate, a Carbonyte
system locks each stone in place.
Helps to eliminate fugitive dust.
Smoother ride, greater contrast.
A cost-effective manner of extending the life of
a chip-sealed roadway, Carbonyte provides:
A waterproof surface coating
A quieter ride with less dust
Improved contrast
Better chip retention
Longer chip seal life and
Promotes quicker water drainage
Waterproofs the roadway.
The RaynMaker Protecting Chip Sealed Roadways
Various Tank Sizes Available Sprays to 13’6” (or more)
If your needs run to 8 lane highways
with 115,000 vehicles per day, the
RaynMaker system can help you
with that also.
Bangkok, Thailand - 2008
Government officials, having done trials on less
traveled pavements, elected to move directly to a
high volume elevated highway. A Carbonyte
SteelGuard material was shipped by ocean voyage from Sacramento to Thailand.
On arrival the SteelGuard was blended with natural latex to provide a tough, wear resistant
surface with good coloration and no loose stone or raveling.
A friction test was performed to assure that the new surface was skid neutral or positive. The
Carbonyte SteelGuard provide excellent traction and a great bonding ability with the new
striping! The RaynMaker system made the job easy.
-----------------------------------------------------------------------------------------------------------
With the RaynMaker built in full-sweep helical mixer, enhancing sealcoat materials for a
challenging task like this is easy. Various latex products, SBS, SBR, tire rubber compounds
and additional fine aggregates can be easily added, mixed and applied.
The RaynMaker System Protecting High Volume Highways
Built for Today’s Maintenance Needs!
9390 Elder Creek Road
Sacramento, CA 95829
1-800-479-9390
www.raynerequipment.com
