| Date post: | 04-Apr-2018 |
| Category: |
Documents |
| Upload: | coolsandy2350 |
| View: | 219 times |
| Download: | 0 times |
of 17
7/31/2019 A Step by Step Guide to Data Test
1/17
Important Points to Remember before Beginning
A Step by Step Guide to Data Testing with the Agilent E6474A Network Optimization Tool 1
A Step by Step Guide to Data Testing with the AgilentE6474A Network Optimization Tool
Important Points to Remember before Beginning
Doing simultaneous trace and data measurements To capture simultaneous data and trace measurements, you will have to make use of 2 COM ports. This
is means either a PCMCIA dual serial card, Edgeport/4 USB hub, or the E6473A Direct Connect Hubmust be used. When using the PCMCIA card or the Edgeport/4 USB hub, the Qualcomm break-out boxwith the proper data cable must be used. When using the E6473A Direct Connect Hub, you must usethe E6473A option 809 cable when using the Kyocera 2235/2255.
Also, if you are using the Kyocera 2235/2255 phone, the second UART must be enabled to dosimultaneous trace and data measurements. Please consult your local BDE about this.
Performing high data rate testing (230 Kbps)
Installing the Kyocera high speed modem driver
With the Qualcomm 1xRTT reference phone and the Kyocera 2235/2255, you must install the highspeed modem driver to allow data rates of up to 230 Kbps. Without this installed you will be limitedto 115 Kbps. See step 5 of Setting up the E6474A for making cdma2000 data measurements forinstructions on how to install the high speed modem drivers. This driver should be included in the
phone connectivity kit. Installing the Edgeport drivers
When the PC is connected to the E6473A Direct Connect Hub, the maximum achievable data rate is230 Kbps if the high speed modem drivers are installed. However, to enable the 230 Kbps data rate,the latest Edgeport drivers must be installed. Without the latest Edgeport drivers, the data rate willbe limited to 115 Kbps. These drivers can be found on the Nitro 3.0 software CD and can also befound on the following web site: http://ionetworks.com/support/index.htm .
If you are only going to be collecting data measurements (no trace measurements) you can make adirect connection from the PC COM port to the phone. This connection will allow up to a 230 Kbpsdata connection so long as the Kyocera high speed modem driver is installed.
When the phone is connected by a dual serial PCMCIA card, the maximum achievable data rate is115 Kbps.
7/31/2019 A Step by Step Guide to Data Test
2/17
Setting up the E6474A for making cdma2000 data measurements
A Step by Step Guide to Data Testing with the Agilent E6474A Network Optimization Tool 2
Setting up the E6474A for making cdma2000 data measurements
Do this Additional Information
1. There are 4 main steps that must be completed inorder to initiate a data call.
Configure the modem
Set up and configure the dial up connection
Set the COM port speed of the phone
Set-up the data call sequence
Note: This step by step document to making cdma2000data measurement is written in the context of Windows2000. If you have a PC with Windows 95, 98, or NT, theprocess may be slightly different.
2. Before configuring your cdma2000 phone as amodem, first make sure the phone is connected tothe PC and that it is properly configured to capture
trace measurements. For further details, refer tothe Step by Step Guide to capture Nitro phoneMeasurements document. Once this is done, fromthe Control Panel, double-click the Phone andModem Options icon.
Important: To capture simultaneous data and tracemeasurements, 2 com ports are necessary. Thismeans either a PCMCIA dual serial card or anE6473A Direct Connect Hub must be used.
3. This displays the Phone and Modem Optionswindow. Click the Add button to add a newmodem device.
7/31/2019 A Step by Step Guide to Data Test
3/17
7/31/2019 A Step by Step Guide to Data Test
4/17
Setting up the E6474A for making cdma2000 data measurements
A Step by Step Guide to Data Testing with the Agilent E6474A Network Optimization Tool 4
Do this Additional Information6. The next window asks which port you want to use
with this modem. Highlight the appropriate COMport and then click Next .
7. A window should now come up stating that youhave successfully set up the modem. Click theNext button.
8. The Phone and Modem Options window is re-displayed. Highlight the standard 19200 bpsmodem that you have just created and click theProperties button.
7/31/2019 A Step by Step Guide to Data Test
5/17
Setting up the E6474A for making cdma2000 data measurements
A Step by Step Guide to Data Testing with the Agilent E6474A Network Optimization Tool 5
Do this Additional Information
9. Once you are in the Properties window of themodem, go to the maximum com port speed pulldown menu. Choose 115200 bps. Then click onDiagnostics tab.
Note: If the Kyocera high speed modem isinstalled, the pull down menu should show 230400bps. Choose 230400 bps if it is available.
Important : The maximum port speed of the modem mustmatch the COM port speed set within the phone.Instructions for setting the com port speed of the phone
7/31/2019 A Step by Step Guide to Data Test
6/17
Setting up the E6474A for making cdma2000 data measurements
A Step by Step Guide to Data Testing with the Agilent E6474A Network Optimization Tool 6
Do this Additional Informationis shown in the Configuring the COM Port Speed of thePhone section of this document.
11. You have now completed the configuration of themodem.
7/31/2019 A Step by Step Guide to Data Test
7/17
Setting up the dial-up network connection
A Step by Step Guide to Data Testing with the Agilent E6474A Network Optimization Tool 7
Setting up the dial-up network connection
Do this Additional Information1. After configuring the modem, you must now set up
the dial up connection. From the Control Panel,double-click the Network and Dial-up Connectionicon.
2. Once the Network and Dial-up Connection windowis displayed, double-click the Make NewConnection icon.
7/31/2019 A Step by Step Guide to Data Test
8/17
Setting up the dial-up network connection
A Step by Step Guide to Data Testing with the Agilent E6474A Network Optimization Tool 8
Do this Additional Information3. This displays the Network Connection Wizard.
Click the Next button.
4. The next window asks you to choose the networkconnection type. Click the dial-up to privatenetwork radio button to place a dot in it, and thenclick the Next button.
7/31/2019 A Step by Step Guide to Data Test
9/17
Setting up the dial-up network connection
A Step by Step Guide to Data Testing with the Agilent E6474A Network Optimization Tool 9
Do this Additional Information5. Next, choose the modem device you will be using
for this connection. The modem device youconfigured earlier should be listed as one of thechoices. Put a check on the appropriate modem
device, and then click the Next button.
6. Now input the appropriate dial-in phone number.This number should be #777. (This number wasset forth by the standards body and should be thesame for all wireless service providers) Make surethe Use dialing rules box is not checked.
7. The next window asks what you want theconnection availability to be. Choose theappropriate box. Typically, the connection can beopen to all users. Then click the Next button.
7/31/2019 A Step by Step Guide to Data Test
10/17
Setting up the dial-up network connection
A Step by Step Guide to Data Testing with the Agilent E6474A Network Optimization Tool 10
Do this Additional Information8. Next, type in a name for this particular dialup
network connection, and then click the Finishbutton.
9. You have now completed the actual setup of the
dial up connection. Next, you must configure thedial up connection. Do this by first clicking theProperties button.
7/31/2019 A Step by Step Guide to Data Test
11/17
Setting up the dial-up network connection
A Step by Step Guide to Data Testing with the Agilent E6474A Network Optimization Tool 11
Do this Additional Information10. Highlight the appropriate modem and click the
Configure button.
11. Make sure the Maximum Speed field is set to115200 bps, and then click the OK button.
Note: If the Kyocera high speed modem isinstalled, the pull down menu should show 230400
bps. Choose 230400 bps if it is available.
Important: Make sure that the COM port speed set in themodem properties window matches the COM port speedset in the phone.
12. You have now completed the set up andconfiguration of the dial up connection.
7/31/2019 A Step by Step Guide to Data Test
12/17
Configuring the COM port speed of the phone
A Step by Step Guide to Data Testing with the Agilent E6474A Network Optimization Tool 12
Configuring the COM port speed of the phone
Do this Additional Information1. You need to select the appropriate com port speed
for the phone. This must be set by actuallymanually going into the phones menu.2. The process of configuring the com port speed of
the phone, is different depending upon the phone.The right column goes through the process in theKyocera 2235/2255.
Kyocera 2235/22551. First go into the main menu.2. Next go into the Settings submenu.3. Click on Accessories.4. Click on Com Port Speed .5. Finally, select the appropriate com port speed.
Important: Make sure that the com port speed set in themodem properties window matches the com port speedset in the phone. For example if 115200 bps is chosen in
the modem properties, then the com port speed of thephone should be 115200. If the Kyocera high speedmodem driver is installed and the maximum modem portspeed is set at 230400 bps, the com port speed of thephone should be set at 230400 bps as well.
7/31/2019 A Step by Step Guide to Data Test
13/17
Setting up the data call sequence with the E6474A
A Step by Step Guide to Data Testing with the Agilent E6474A Network Optimization Tool 13
Setting up the data call sequence with the E6474A
Do this Additional Information1. On the E6474A system setup view, right click on
the Data port to display the context sensitivemenu. Click Add Device .
2. Once the Data Device is added, right click on it tobring up the context sensitive menu, and clickProperties .
3. This displays the Data Properties view. This viewsets up the actual actions of the data call session.
4. Within the Data Properties view, first click on theaction column heading to display its action menu.Highlight and click Connect .
7/31/2019 A Step by Step Guide to Data Test
14/17
Setting up the data call sequence with the E6474A
A Step by Step Guide to Data Testing with the Agilent E6474A Network Optimization Tool 14
Do this Additional Information5. Then click on the target field to the right. This
displays the ISP login window. Click the downarrow in the Dial Up field to display a pull downmenu. Then choose the previously-created dial up
connection.
6. Enter the ISP user name and password, and thenclick OK.
7/31/2019 A Step by Step Guide to Data Test
15/17
7/31/2019 A Step by Step Guide to Data Test
16/17
Setting up the data call sequence with the E6474A
A Step by Step Guide to Data Testing with the Agilent E6474A Network Optimization Tool 16
Do this Additional Information8. Once you have finished with creating your data
sequence, click the Validate button to check forany errors (for example, a missing web address,etc.). If no errors are found, click the OK button.
9. Now open the desired data views, by selecting theview menu.
The following are data associated views: Data Message Log Identifies current
status/position within the data sequence
Data Measurements Server-based genericdata measurements
Web Measurements Public Internet datameasurements (data measurements not usingthe server license)
Data plot line graph of generic dataparameters
For more information, please access the helptopics pressing F1.
10. Now, save the project file. On the E6474A MenuBar, select File > Save and give the project a filename.
This saves a project file with the phone setup andconfigured. To make data measurements with the sameconfiguration in the future, simply open this project file.
7/31/2019 A Step by Step Guide to Data Test
17/17
Setting up the data call sequence with the E6474A
A Step by Step Guide to Data Testing with the Agilent E6474A Network Optimization Tool 17
Do this Additional Information11. Start the measurements by selecting the Live
Mode button (Yellow button) or by selecting Log >Start Live Mode .
You can also start the measurements with Logging Moderather than Live Mode. Logging Mode allows you toreplay the measurement data at a later time. However,once logging has been started, you will be unable tochange any of the measurement
Unless you need to record the measurement data toanalyze it at a later time, Live Mode provides moreflexibility over Logging Mode.You can capture data during Live Mode by taking asnapshot of the measurement data with the reportgenerator. To use report generator, select Tools >Report Generator .
![FRbcW]U€¦ · Step 2. Test Get an onsite test performed by our trusted medical partners. Step 3. Evaluate Lab receives, evaluates, and quickly returns test results. Step 4. Receive](https://static.documents.pub/doc/80x56/60a26fcc0b27795a9656b4cd/frbcwu-step-2-test-get-an-onsite-test-performed-by-our-trusted-medical-partners.jpg)
