AUTOMATIC OVERDRIVE TRANSMISSION

INTERMEDIATE

SERVO

OVERDRIVESERVO

HIGH CLUTCH

COAST CLUTCH

FORWARD CLUTCH

NOT SERVICED SEPARATELYMODEL DEPENDENT

92794PTPE VERSION

REVERSESERVO

A4LD (2.3L/3.0L) TRUCK

1. 7902 CONVERTER ASY (CONTAINS PISTON TYPE CLUTCH)2. 379299S2 NUT (ATT. CONVERTER ASY TO FLEX PLATE) (REF 4 REQ’D)3. 7017 SHAFT (INPUT)4. 7A248 SEAL ASY (CONVERTER HUB TO CONVERTER HOUSING) (ALSO IN CONVERTER HOUSING ASY)5. 7B258 BUSHING (FRONT FLUID PUMP TO CONVERTER HOUSING) (PART OF CONVERTER HOUSING ASY)6. E804595S200 SCREW & SEAL ASY M10 X 33 (ATT. CONVERTER HOUSING TO CASE) (8 REQ’D)7. 7975 HOUSING ASY (CONVERTER)8. 7B472 PLATE (FLUID PUMP ADAPTOR)9. 7A136 GASKET (FRONT FLUID PUMP)

10. 7L323 SEAL RING (FRONT PUMP SUPPORT)11. 7L201 SUPPORT & GEAR ASY (FRONT PUMP)12. 7D014 WASHER (FRONT PUMP INPUT THRUST)(SELECT FIT) #113. E804375S72 SCREW FLANGE HEAD 8.8 ALLEN M8 X 35 (ATT. PUMP ASY TO CONVERTER HOUSING) (5 REQ’D)

14. 7D429 SEAL RING (O.D. BRAKE DRUM) (2 REQ’D)15. 7D441 SEAL RING (FRONT FLUID PUMP)16. E825100S100 NUT & SEAL HEX (INTERMEDIATE & O.D. BAND) ADJUSTER/LOCK (2 REQ’D)17. 7C492 SCREW (INTERMEDIATE & O.D. BAND) ADJUSTER/LOCK (2 REQ’D)18. 7D430 STRUT (INTERMEDIATE & O.D. BAND) ANCHOR (2 REQ’D)19. 7A653 BRACKET (O.D. BAND LEVER TO CASE)20. 7D433 SHAFT (O.D. BAND) ACTUATING LEVER21. 7D396 LEVER (INTERMEDIATE & O.D. BAND) SERVO (2 REQ’D)22. 7D029 STRUT (INTERMEDIATE & O.D. BAND) APPLY (2 REQ’D)23. 7D03424. 7L669 DRUM ASY (O.D. BRAKE & COAST CLUTCH)25. 7D404 SEAL RING (COAST CLUTCH PISTON) INNER26. 7A548 SEAL RING (COAST CLUTCH PISTON) OUTER27. 7A258 PISTON (COAST CLUTCH)28. 7C151 SPRING (COAST CLUTCH) PISTON (15 REQ’D)29. 7D041 RETAINER (COAST CLUTCH) PISTON SPRINGS 8 TABS

30. E860125S RING RETAINING 63MM (COAST & HIGH CLUTCH PISTONS IN THEIRBRAKE DRUMS) (2 REQ‘D)

31. 7B442 PLATE (COAST CLUTCH EXTERNAL) STEEL (3)32. 7B164 PLATE ASY (COAST CLUTCH INTERNAL) FRICTION (3)33. 7B066 PLATE (COAST CLUTCH) PRESSURE34. E860126S RING RETAINING (SELECT FIT) (COAST & HIGH CLUTCH PLATES) (2 REQ’D)

E860127S RING RETAININGE860128S RING RETAININGE860129S RING RETAINING

35. 7660 ADAPTOR (COAST CLUTCH) (TO O.D. CARRIER)36. 7D063 GEAR ASY (SUN O.D.)37. 7D235 RACE (SUN GEAR THRUST BEARING REAR) (ALL) #1238. 7B446 CARRIER ASY (PLANETARY GEAR O.D.)39. 7L495 BEARING ASY (O.D. PLANET THRUST) #240. 7653 GEAR (O.D. RING)41. 7C109 CLUTCH ASY (OVERRUNNING O.D.)42. 7686 SHAFT ASY (CENTER O.D.)43. E860119S RING RETAINING 110.1 MM (O.D. CENTER SHAFT IN O.D. RING GEAR)44. 7C122 RING RETAINING (CENTER SUPPORT IN CASE)45. 7D014 BEARING ASY (CENTER SHAFT THRUST) #346. E826160S76 NUT & CAGE ASY S/L MET. M6 (ATT. CENTER SUPPORT TO CASE)47. E804373S SCREW (CAP) 8.8 ALLEN M6 X 20 (ATT. CENTER SUPPORT TO CASE)48. 7G033 SUPPORT ASY (CENTER)49. 7D014 WASHER (INTERMEDIATE BRAKE DRUM THRUST) SELECT FIT #450. 7D429 SEAL RING (INTERMEDIATE BRAKE DRUM) (2 REQ’D)51.52.

7D433 SHAFT (INTERMEDIATE BAND) ACTUATING LEVER

53.7D044 DRUM ASY (INTERMEDIATE BRAKE & HIGH CLUTCH)

54.7D404 SEAL RING (HIGH CLUTCH PISTON) INNER

55.

7A548 SEAL RING (HIGH CLUTCH PISTON) OUTER

56.7A258 PISTON (HIGH CLUTCH)

57.7C151 SPRING (HIGH CLUTCH) PISTON (20 REQ’D)

58.7D041 RETAINER (HIGH CLUTCH) PISTON SPRINGS 8 TABS

59.7B442 PLATE (HIGH CLUTCH EXTERNAL) STEEL (4 OR 5 REQ’D)

60.7B164 PLATE ASY (HIGH CLUTCH INTERNAL) FRICTION (4 OR 5 REQ’D)

61.7B066 PLATE (HIGH CLUTCH) PRESSURE

62.7D428 WASHER (FORWARD CLUTCH CYLINDER THRUST) #5

63.7D019 SEAL RING (FORWARD CLUTCH CYLINDER) (2 REQ’D)

64.7D424 CYLINDER ASY (FORWARD CLUTCH)

65.7D504 SEAL RING (FORWARD CLUTCH PISTON) INNER

66.7A548 SEAL RING (FORWARD CLUTCH PISTON) OUTER

67.7A262 PISTON ASY (FORWARD CLUTCH)

68.7C151 SPRING (FORWARD CLUTCH) PISTON (15 REQ’D)

69.7D041 RETAINER (FORWARD CLUTCH) PISTON SPRINGS

70.

E860109S RING RETAINING 34MM (FORWARD CLUTCH PISTON & SPRINGSIN FORWARD CLUTCH CLYLINDER)

71.7E457 SPRING (FORWARD CLUTCH CUSHION)

72.7B442 PLATE (FORWARD CLUTCH EXTERNAL) STEEL (5 REQ’D)

73.7B164 PLATE ASY (FORWARD CLUTCH INTERNAL) FRICTION (5 REQ’D)

74.7B066 PLATE (FORWARD CLUTCH) PRESSURE

75.

E860115S RING RETAINING (SELECT FIT) (FORWARD CLUTCH PLATESIN FORWARD CLUTCH CYLINDER)

E860116S RING RETAININGE860117S RING RETAININGE860118S RING RETAINING

76.7D234 BEARING ASY (FORWARD RING GEAR HUB THRUST) #6A

77.7D090 WASHER (FORWARD CLUTCH THRUST) #6B

78.

E860122S RING RETAINING 87MM (FORWARD & OUTPUT SHAFT RING GEARSTO THEIR HUBS) (2 REQ‘D)

79.7D393 HUB (FORWARD RING GEAR)

80.7D392 GEAR (FORWARD RING) 72 EXTERNAL TEETH & 57 INTERNAL TEETH

81.7F374 BEARING ASY (FORWARD PLANET THRUST) #7

82.7A398 PLANET ASY (FORWARD) (SERVICED AS 6PINION ONLY)

83.E860121S RING RETAINING 39MM (INPUT SHELL TO SUN GEAR ASY) (2 REQ’D)

84.7D066 WASHER (INPUT SHELL THRUST) #14 (2.3L & 3.0L CONTAINS 2 BUSHINGS)

85.7D063 GEAR ASY (SUN FORWARD)

86.7D064 SHELL (INPUT)

87.7D423 WASHER (REVERSE PLANET CARRIER THRUST) #8 & #9

88.E860119S RING RETAINING (REVERSE PLANET IN OUTPUT RING GEAR)

89.7D006 PLANET ASY (REVERSE) (3 OR 4 PINION)

90.7A153 GEAR (OUTPUT SHAFT RING)

91.E860527S RING RETAINING 25 X 2MM (OUTPUT SHAFT IN CASE)

92.7D164 HUB (OUTPUT SHAFT)

93.7C498 DRUM ASY (REVERSE BRAKE)

94.7190 ROLLER (LOW OVERRUNNING CLUTCH) (10 REQ’D)

95.7D191 RETAINER (LOW OVERRUNNING CLUTCH SPRING)

96.E860120S RING RETAINING (LOW OVERRUNNING CLUTCH)

97.7D095 BAND ASY (REVERSE)

98.7D422 WASHER (OUTPUT SHAFT HUB THRUST) #10

99.7D171 RACE (LOW OVERRUNNING CLUTCH INNER) (PART OF CASE ASY)

100.7025 BUSHING (OUTPUT SHAFT TO CASE) (PART OF CASE ASY)

101.E840171S2 PIN (REVERSE BAND ANCHOR) (2 REQ’D) (PART OF CASE ASY)

102.7B368 WASHER (OUTPUT SHAFT THRUST) #11

103.7D011 RING (GOVERNOR HOUSING SEAL) (3 REQ’D)

104.7D220 BODY (GOVERNOR OIL) COLLECTOR

105.

E800156S SCREW M6 X 20 (ATT. GOVERNOR BODY TO COLLECTOR BODY) (2 REQ’D)& (ATT. REVERSE SERVO COVER TO CASE) (4 REQ’D)

106.7A300 BODY (GOVERNOR VALVE)

107.7C054 VALVE (GOVERNOR PRIMARY)

108.7A302 SPRING (GOVERNOR VALVE)

109.7D324 WEIGHT (GOVERNOR VALVE)

110.7F124 COUNTERWEIGHT GOVERNOR

111.E602164S72 SCREW M6 X 12 (ATT. COUNTERWEIGHT TO COLLECTOR BODY) (2 REQ’D)

112.7A043 BEARING ASY (OUTPUT SHAFT TO CENTER SHAFT) (PART OF OUTPUT SHAFT ASY)

113.7060 SHAFT ASY (4 X 2 OUTPUT)

114.7086 GASKET EXTENSION HOUSING

115.7D419 CUP (PARKING ROD GUIDE) (PART OF EXTENSION HOUSING ASY)

116.7060 (SHAFT ASY) (4 X 4 OUTPUT)

117.7D070 SPRING (PARKING PAWL RETURN)

118.7A441 PAWL (PARKING)

119.7D071 SHAFT (PARKING PAWL)

120.7A039 HOUSING ASY (4 X 2 EXTENTION)

121.E800152S72 SCREW M10 X 30 (ATT. EXTENSION HOUSING TO CASE) (4 REQ’D)

122.E804137S72 STUD (ATT. EXTENSION HOUSING TO CASE) (2 REQ’D)

123.N605804S100 SCREW M10 X 45 (ATT. 4 X 4 EXTENSION HOUSING TO TRANSFER CASE) (REF 5 REQ’D)

124.7A039 HOUSING ASY (4 x 4 EXTENSION)

125.7A034 BUSHING (4 X 2 EXTENSION HOUSING) (ALSO IN EXTENSION HOUSING ASY)

126.7052 SEAL ASY (EXTENSION HOUSING TO SLIP YOKE) (ALSO IN EXTENSION HOUSING ASY)

127.E820109S72 NUT HEX M8 X 1 (RETAINS OUTER TO INNER DOWNSHIFT LEVER)

128.7A394 LEVER ASY (DOWNSHIFT CONTROL OUTER)

129.386078S O’RING (OUTER MANUAL LEVER SHAFT TO CASE)

130.7A256 LEVER ASY (MANUAL CONTROL)

131.E840125S PIN SPRING (RETAINS OUTER MANUAL LEVER TO CASE)

132.7B498 SEAL ASY (MAIN CONTROL LEVER (ALSO IN CASE ASY)

133.E662312S CLIP RETAINING (MANUAL VALVE PIN ZLINK)

134.7C494 LEVER (MANUAL VALVE INNER)

135.E630020S71 WASHER FLAT STEEL (PIN ZLINK TO INNER VALVE LEVER)

136.7E333 PIN ZLINK (MANUAL VALVE DETENT LEVER) INNER

137.7D261 LEVER ASY (DOWNSHIFT DETENT INNER)

138.E800185S SCREW M6 X 30 (ATT. DETENT SPRING TO MAIN CONTROL)

139.7E332 SPRING ASY (MANUAL VALVE DETENT)

140.W701271S309 NUT (ATT. OUTER TO INNER MANUAL LEVER)

141.7D410 ROD ASY (PARKING PAWL ACTUATING)

142.7A247 SWITCH ASY (PARK & NEUTRAL POSITION SENSOR)

143.E853116S O’RING (NEUTRAL SWITCH TO CASE)

144.7005 CASE ASSEMBLY

145.E450102S80 PLUG PIPE (LINE PRESSURE) (PART OF CASE ASY)

146.7034 VENT ASY (4 X 2 CASE) (ALSO CONTAINED IN CASE ASY)

147.7034 VENT ASY (4 X 4 CASE) (ALSO CONTAINED IN CASE ASY)

148.E800341S72 SCREW M6 X 12 (ATT. T.V. CLAMP TO CASE) (NON 4 X 4)

149.E804533S201 STUD M6M6 X 12 (ATT. T.V. CLAMP TO CASE)

150.7D080 VALVE (THROTTLE CONTROL)

151.7A380 ROD (TV CONTROL)

152.E853110S O’RING (THROTTLE CONTROL VALVE TO CASE)

153.7E458 CLAMP (TV CONTROL DIAPHRAGM)

154.7A377 DIAPHRAGM ASY (TV CONTROL)

155.E860343S RING RETAINING 67 X 1.5MM (INTERMEDIATE & O.D. SERVOS IN CASE) (2 REQ’D)

156.E853170S O’RING (SERVO COVER TO CASE) (INTERMEDIATE & O.D. SERVOS) (2 REQ’D)

157.7L493 COVER & SEAL ASY (INTERMEDIATE SERVO)

158.7E221 PISTON & ROD ASY (INTERMEDIATE SERVO)

159.7D028 SPRING (INTERMEDIATE SERVO PISTON)

160.7L493 COVER & SEAL ASY (O.D. SERVO)

161.7E221 PISTON & ROD ASY (O.D. SERVO)

162.7D028 SPRING (O.D. SERVO PISTON)

163.7D273 CONNECTOR ASY FLUID TUBE (2 REQ’D) (ALSO IN CASE ASY)

164.7N463 TUBE (LUBE FLUID INLET) SHORT (ALSO IN CASE ASY)

165.50920000626 O’RING (SOLENOID CONNECTOR TO CASE) (2 REQ’D)

166.7E449 CONNECTOR (CONVERTER CLUTCH 34 SHIFT SOLENOIDS)

167.7D100 GASKET (CONTROL VALVE BODY TO CASE)

168.

E804357S76 SCREW TORX M6 X 21 (ATT. SEPARATING PLATE TO MAIN CONTROL) (ALSO INMAIN CONTROL ASY) (3 REQ’D)

169.7A008 PLATE (VALVE BODY SEPARATING) (PART OF MAIN CONTROL ASY)

170.7D100 GASKET (CONTROL VALVE BODY SEPARATING) (ALSO IN MAIN CONTROL ASY)

171.6916 SOLENOID ASY (34 SHIFT) (ALSO IN MAIN CONTROL ASY)

172.7M082 CLAMP (34 SOLENOID) (ALSO IN MAIN CONTROL ASY)

173.6916 SOLENOID ASY (CONVERTER CLUTCH WITH CLAMP) (ALSO IN MAIN CONTROL ASY)

174.7A100 CONTROL ASY (MAIN)

175.7D031 SPRING (REVERSE SERVO PISTON)

176.E800153S SCREW M6 X 40 (ATT. MAIN CONTROL TO CASE) (17 REQ’D)

177.

E800154S SCREW M6 X 45 (ATT. MAIN CONTROL TO CASE) (4 REQ’D)& (ATT. FLUID SCREEN TO MAIN CONTROL)

178.E800163S SCREW M6 X 35 (ATT. MAIN CONTROL TO CASE) (3 REQ’D)

179.7D190 ROD (REVERSE SERVO) (PART OF PISTON ASY)

180.E830138S RETAINER (REVERSE SERVO CUSHION SPRING) (ALSO IN PISTON ASY)

181.7E207 SPRING (REVERSE SERVO CUSHION) (ALSO IN PISTON ASY)

182.7423 SEAL RING (REVERSE SERVO PISTON) SMALL (ALSO IN PISTON ASY)

183.7E266 PISTON (REVERSE SERVO)

184.7423 SEAL RING (REVERSE SERVO PISTON) LARGE (ALSO IN PISTON ASY)

185.E860167S RING RETAINING (REVERSE SERVO ROD TO PISTON) (PART OF PISTON ASY)

186.7L173 GASKET (REVERSE SERVO COVER TO CASE)

187.7D036 COVER (REVERSE SERVO)

188.7D030 PISTON ASY WITH ROD & RETAINER (REAR BAND SERVO) (SELECT FIT)

189.E853137S O’RING (FLUID SCREEN ASY) SMALL

190.7A098 SCREEN ASY (4 X 2 FLUID PAN)

191.E853132S O’RING (FLUID SCREEN ASY) LARGE

192.7A191 GASKET (FLUID PAN)

193.E802198S72M SCREW M8 X 14 (ATT. FLUID PAN TO CASE) (18 REQ’D)

194.7A264 PAN (4 X 2 FLUID)

195.7A098 SCREEN ASY (4 X 4 FLUID PAN)7A264 PAN (4 X 4 FLUID)

BAND ASY (INTERMEDIATE & O.D.) (2 REQ’D.)

Illustration Section

TECHNICALand

TRANSPORTATION SERVICES

CTF4XX070100A4LD2330PTPEC2