(A2LA Cert. No. 2743.01) Revised 02/28/2011 Page 1 of 24

SCOPE OF ACCREDITATION TO ISO/IEC 17025:2005

SCI−LAB MATERIALS TESTING INC. 150 Trillium Drive

Kitchener, ON, CANADA Richard Isaacs Phone: 519 895 0500

MECHANICAL

Valid To: March 31, 2011 Certificate Number: 2743.01

In recognition of the successful completion of the A2LA evaluation process, accreditation is granted to this laboratory to perform the following types of tests on Adhesives (Organic Resins), Glues, Paints, Varnishes, Inks, Coatings, Allied Products, Plastics, Resins, Rubbers, and Articles of Metal:

TEST

TEST METHOD

Abrasion/Wear, Scratch/Mar Resistance & Fatigue Scratch Resistance 8350Z-SDA-9000 Standard Test Method for Resistance of Transparent Plastics to Surface Abrasion

ASTM D1044

Standard Test Method for Rubber Property – Abrasion Resistance (Footwear Abrader)

ASTM D1630

Standard Test Method for Abrasion Resistance of Organic Coatings by the Taber Abraser

ASTM D4060

Standard Guide for Abrasion Resistance of Textile Fabrics (Rotary Platform, Double-Head Method)

ASTM-D3884

Standard Test Method for ASTM-D4482 Standard Test Methods for Rubber Property—Heat Generation and Flexing Fatigue In Compression

ASTM-D623

Flex Fatigue CPNM-MOS-ST-10-04-07-E Exterior Paint System - Mar & Scratch Resistance DVM-0034 PA; DVM -0035 PA Resistance for Exterior Part Mar DVM-0034-PA Scratch Resistance for Exterior Paint DVM-0035-PA Friction Induced Wear of Exterior Finishes DVM-0056-PA Crocking Test FLTM BN 107-01 Resistance to Abrasion-Taber Abraser FLTM BN 108-02 Five Finger Scratch Resistance FLTM BN 108-03 Resistance to Scuffing FLTM BN 108-04 Crockmeter Scuff Test FLTM BN 108-10 Five Finger Scratch Resistance FLTM BN 108-13 Resistance to Scratching FLTM BN 108-13 Scratch Resistance FLTM-108-13

TEST TEST METHOD

(A2LA Cert. No. 2743.01) Revised 02/28/2011 Page 2 of 24

Resistance to Marring or Scuffing GM9150P Test for Stress Mark Susceptibility of Plastic Materials GM9302P Car Wash Simulation Test GM9600P Scratch and Mar Resistance of Plastics, Five Arm Test GMN3943 Resistance to Marring or Scuffing GMW14130 Scratch and Mar Resistance GMW14688 Color Fastness to Rubbing JIS L0823 Test Method for Color Fastness to Rubbing JIS L0849 Wear Resistance of Trim Materials – Taber Method LP 463KB-21-01 Scratch and Mar Resistance of Automotive Plastics – Determination of

LP-463DD-18-01

Resistance to Dye Transfer (Water Dye Test) LP-463KC-1-01 Paint – Mar Resistance Test (Physical Testing) LP-463PB-43-01 Crock Mar Resistance LP-463PB-54-01 Testing Method of the Scratch Resistance of Interior Polypropylene Resin Parts

NES M 0159

Abrasion Resistance Test Methods for Plastic Parts NES M0136 Method of Testing Resistance to Scuffing of Trim Materials SAE J365 Method of Testing Resistance to Crocking of Organic Trim Materials

SAE J861

Test Method for Determining Resistance to Abrasion of Automotive Bodycloth, Vinyl, and Leather, and the Snagging of Automotive Bodycloth

SAE J948

Abrasive Wear SAE J965 Standard Test Methods for Woven Fabrics and Knitted Fabrics TSL2100G Adhesion/Cohesion & Peel Strength Adhesive Specification for Interior Parts 0095Z-S04-0000 Test Method Specification for Adhesive (General) 0095Z-SDA-A000 Standard Test Methods for Rubber Property – Adhesion to Flexible Substrate

ASTM D413

Standard Test Methods for Rubber Property – Adhesion to Rigid Substrates

ASTM D429

Standard Test Method for Peel or Stripping Strength of Adhesive Bonds

ASTM D903

Standard Test Methods for Bond or Cohesive Strength of Sheet Plastics and Electrical Insulating Materials

ASTM D952

Standard Test Methods for Measuring Adhesion by Tape Test ASTM D3359 Exterior paint System Adhesion DVM-0023-PA Determination of Inert Fillers in Polymers FLTM BO 106-01 Peel Adhesion of Pressure Sensitive Tapes FLTM BU 112-02 Cold Adhesion Test for Double Faced Pressure Sensitive Tapes FLTM BU-109-02 Tape Wet-Out Test GM9837P Adhesion Requirement for External Plastic Trim Attached With Pressure Sensitive Adhesive Tape

GM3604M

Adhesion Requirements of Interior Carpets GM3608M Adhesion Requirements of Pressure Sensitive Adhesive Coated Parts (Minimal Stress)

GM3622M

Adhesion Performance of Decorative Exterior Emblems and GM6271M

TEST TEST METHOD

(A2LA Cert. No. 2743.01) Revised 02/28/2011 Page 3 of 24

Script Knife Cross-Hatched Adhesion Test Procedure for Painted Elastomeric Plastic Substrates

GM9502P

Molding and Emblem Adhesion Test Pluck Resistance GM9774P Cleavage Peel Test GM9797P Tape Lamination to Automotive Components GM9838P Adhesion of Water Strips to Paint, Paint Staining and Wrinkle Resistance

GM9896P

Testing Methods for Adhesives for Automobiles JIS K 6829 Bond Strength LP 463LB-10-01 Adhesion LP 463TB-11-01 Peel Strength and Adhesion – Determination of LP 463TB-3-01 Shear Adhesion LP 463TB-8-01 Bond Strength (Destructive Bond Pull Test) MIL-STD-883G Method 2011.7 Adhesive Water Dispersion Type MS-CB 124 Separation Strength NES M0152 Cross Peel Test for Automotive Type Adhesives for Fiber-Reinforced Plastic (FRP) Bonding

SAE J1553

Peel Strength of Soft Trim Materials SAE J1679 Surface Match Verification Method for Pressure Sensitive Adhesively Attached Components

SAE J2215

Test Method for Quality Requirements of Exterior Plastic Parts TS 371-0-4, (10) Double-Coated Adhesive Tapes for Interior Trim Materials TSK5702G Ash & Filler Content Standard Test Method for Ash Content in Plastics ASTM D5630 Determination of Ash Content of Resins FLTM BO 006-01 Determination of Ash Content of Molding Materials FLTM BO 006-02 Determination of Filler Content in Polytetrafluoroethylene FLTM BO 006-03 Resistance of Polyurethane Foam to Deterioration FLTM BO 012-01 Determination of Inert Fillers in Polymers FLTM BO 106-04 Determination of Ash Content of Moulded Materials FLTM EU BO 006-02 Ash Content of Plastics GM9306P Variable Surface Temperature Heat Exposure Test GM9310P Plastics – Determination of ash – Part 1: General Methods ISO 3451-1 Plastics – Determination of ash – Part 4: Polyamides ISO 3451-4 Determination of Percentage Ash Solids LP 463DB-13-01 Volatile Loss of Thermoplastic Materials LP 463DD-4-01 Bend Test, Flexibility & Deflection Standard Test Method for Seal Quality of Anodic Coatings on Aluminum by Acid Dissolution

ASTM B680

Standard Specification for Flexible Cellular Materials - Sponge or Expanded Rubber

ASTM D1056

Standard Test Method for Brittleness Temperature of Plastic Sheeting by Impact

ASTM D1790

Standard Test Methods for Flexible Cellular Materials-Slab, Bonded, and Molded Urethane Foams

ASTM D3574

Standard Test Methods for Flexible Cellular Materials Made from Olefin Polymers

ASTM D3575

TEST TEST METHOD

(A2LA Cert. No. 2743.01) Revised 02/28/2011 Page 4 of 24

Standard Test Method for Brittleness Temperature of Plastics and Elastomers by Impact

ASTM D746

Standard Test Methods for Flexural Properties of Unreinforced and Reinforced Plastics and Electrical Insulating Materials

ASTM D790

Standard Test Method for Rubber Property—Plasticity and Recovery (Parallel Plate Method)

ASTM D926

Bend Test for Coating Adhesion FLTM BI 009-05 Evaluating Brittleness of Painted Plastics and Sealants by Means of a Mandrel

GM9503P

Loading IP-0021 Rigid Cellular Plastics – Determination of Flexural Properties – Basic Bending Test

ISO 1209

Plastics - Determination of Flexural Properties ISO 178 Plastics - Determination of the Brittleness Temperature by Impact

ISO 974

Testing Method for Flexuarl Properties of Rigid Plastics JIS K7203 Load Deflection Test LP 463AB−5−08 Low Temperature-Mandrel Bend Test (Brittleness) LP 463AB-25-01 Load Deflection Test LP 463AB-5-04 Plastic – Cellular - Molded Polyurethane High Resilience - Seal Applications

MS-DC634

Test Method for Quality Requirements of Exterior Plastic Parts TS 371-0-4 Chemical/Staining Resistance & Cleanability Standard Test Method for Effect of Household Chemicals on Clear and Pigmented Organic Finishes

ASTM D1308

Standard Practices for Evaluating the Resistance of Plastic to Chemical Reagents

ASTM D543

Standard Test Methods for Rubber Property—Staining of Surfaces (Contact, Migration, and Diffusion)

ASTM D925

Standard Test Methods for Fluid Resistance of Gasket Materials ASTM F146 Exterior Paint System Fluid Spotting Resistance DVM 0037-PA Cleanability of Exterior Grained Surfaces DVM-0012-OR Soiling & Cleanability – Interior Trim Materials DVM-0017-MA Chemical Compatibility DVM-0027-MA Fluid Spotting Resistance DVM-0037-PA Exterior Finish High Pressure Water Wash DVM-0041-PA Road Asphalt Stain Resistance DVM-27881 Padding, Polyester Fiber, Pressure Sensitive Adhesive Backed, Needled 0.339kg/m2

ESB-M17H158-A

Resistance of Textiles to Bleeding, Perspiration and Water Spotting

FLTM AN 101-01

Water and Soap Spotting Test for Paint FLTM BI 113-01 Resistance to Acid Spotting FLTM BI 113-02 Resistance to Synthetic Perspiration Staining FLTM BI 113-03 Cleanability Test for Outside Vinyl Coated Material FLTM BN 012-06 Soiling and Cleanability for Interior Trim Materials FLTM BN 112-08 Determination of Fuel Resistance of Plastic Parts FLTM BO 101-05 Resistance of Painted Plastic Parts to High Pressure Cleaning Operations

FLTM BO 160-04

TEST TEST METHOD

(A2LA Cert. No. 2743.01) Revised 02/28/2011 Page 5 of 24

Staining of Surfaces by Polymers and Elastomers FLTM BP 153-01 Cleanability of Textiles and Plastics, Test for GM9126P Compatibility of Plastic Rolled Goods and Leather to White Vinyl and to White Leather

GM9141P

Cleanability of Convertible Top and Roof Trim Materials GM9147P Method for Determining the Soil Pick-up and Cleanability of Vinyl Materials

GM9156P

Water Jet Tests GM9531P Soil and Cleaner Resistance of Automotive Materials GMW3402 Performance Requirements for Exterior Plastic Parts GM7452M Test for Resistance to Hydrogen Sulfide Staining GM9069P Water Spotting GM9133P Staining Resistance GM9172P Gasoline Puddle Test for Gasoline Fill Areas GM9500P Gasoline Dip Test for Painted Parts GM9501P Solvent Rub Method for Determining Cure of Painted Metal or Plastic Substrates

GM9509P

Asphalt Staining Test GM9689P Sulfur Dioxide Spot Test GM9736P Sunscreen Lotion Resistance of Interior Coatings GMN10033 Migration – Bleeding Resistance and Contact Stain Compatibility of PVC with other Materials

GMW14069

Resistance to Fuels of Exterior Automotive Materials and Components

GMW14333

Chemical Resistance to Fluids GMW14334 Sunscreen and Insect Repellent Resistance GMW14445 Procedure for Determining the Staining of Trim Materials Due to Sulfur Dioxide, SO2, and Hydrogen Sulfide, H2S

GMW14864

Procedure for Determining Soil and Cleaner Resistance of Automotive Materials

GMW3402

Rubber, Vulcanized or Thermoplastic – Methods of Tests for Staining in Contact with Organic Material

ISO 3865

Motor Gasoline JIS K 2202 Kerosine JIS K 2203 Staining of Soft Trim Materials LP 463CB-14-01 Cleanability of Interior Trim LP 463KC-04-01 Acid Spot Test LP 463PB-06-01 Resistance of Paint Films to Various Fluids LP 463PB-31-01 Solvent Wipe Resistance Test LP 463PB-7-01 Water Spotting Resistance of Soft Trim Materials LP-463KC-03-01B Cleanability of Interior Trim LP-463KC-04-01-H High Pressure Car Wash Resistance MDT-060 Plastic - Cellular – Molded Polyurethane – High Resilience – Seal Applications

MS-DC634

Cellular – Molded Polyurethane – High Resilient (HR) Type – Seat Applications

MS-DC-648

Chemical Resistance Test Methods for Plastic Parts NES M0133 Clouding Test NES M7083 Suntan Lotion Resistance TM-GEN-022B Grease Staining Resistance Test Method for Interior Parts Paint TSH1562G

TEST TEST METHOD

(A2LA Cert. No. 2743.01) Revised 02/28/2011 Page 6 of 24

Performance, Polymeric Foam For Seating Applications, Including Cushions, Armrests, And Headrestraints - Staining

WSS-M15P20-B1/B2

Cold Cracking & Impact Cold Impact 77211-SJC-A000-20 Side Impact Specification for Door LNG Side Impact – (Dynamic Test)

8352Z-STXA-A000

Door LNG Side Impact Specification 8352ZSZA_A000 Specification for Front Door LNG Side Impact 8352Z-TA0A-V000 Spec for RR Door LNG Side Impact 8373Z-TA0A-V000 High Impact PP for Center Pillar Lower Specification 8412Z-SEP-A020-M2 Standard Test Methods for Impact Resistance of Plastic Film by the Free-Falling Dart Method

ASTM D1709

Standard Test Methods for Determining the Izod Pendulum Impact Resistance of Plastics

ASTM D256

Standard Test Method for Resistance of Organic Coatings to the Effects of Rapid Deformation (Impact)

ASTM D2794

Standard Test Method for High Speed Puncture Properties of Plastics Using Load and Displacement Sensors

ASTM D3763

Standard Test Method for Impact Resistance of Flat, Rigid Plastic Specimen by Means of a Striker Impacted by a Falling Weight (Gardner Impact)

ASTM D5420

Molding Impact Test DVM-14144v4 Polymeric Materials – Low Temperature Flexibility FLTM BN 102-01 Low Temperature Impact Test for Plastics FLTM BO 151-01; FLTM BO 151-02; GM9011P Cold Flexibility of Plastic Film and Sheeting FLTM EU BO 051-09 Interior Impact FMVSS 201 Test for Determining Impact Strength of Plastics GM9032P Resistance to Cold Cracking of Leather and Plastic Rolled Goods

GM9140P

Impact Test for Plastic Materials – Instrumented or Non-Instrumented

GM9300P

Impact Test Exterior Body Side Moldings GM9528P Cold Slam Test GM9773P Multi-Axial Impact Test GM9904P Determination of Impact Resistance of Plastic Components GMW14093 General Test Methods of Resin Materials for Vehicles HES D 2500 Impact Durability Honda 3575Z-SNA-0000, 3.18 Test Ef: Impact, Pendulum Hammer. Amendment 1 (1993) IEC 68-2-62 Determination of Izod Impact Strength ISO 180 Determination for Multiaxial Impact Behaviour of Rigid Plastics - Falling Dart Method

ISO 6603-1

Determination of Puncture Impact Behaviour of Rigid Plastics – Instrumented Impact Testing

ISO-6603-2

Method of Izod Impact Test for Rigid Plastics JIS K7110 Impact Resistance – Parts or Test Plaques – Gardner Falling Weight Test Apparatus

LP 463DB-14-01

Impact Resistance LP 463PB-19-01 Cold Cracking Resistance of General Trim Materials LP-463LB-11-01 Cold Cracking Resistance of General Trim Materials LP-463LB-11-01B

TEST TEST METHOD

(A2LA Cert. No. 2743.01) Revised 02/28/2011 Page 7 of 24

Bonded Moldings, Die-Cast Ornaments, and Appliqués LP-463TB-9-01 Falling Ball Impact test Methods for Synthetic Resin Parts NES M0134 Instrument Panel Module System Requirements: Cold Impact Requirements

PF-11014, 3.3

Plastic Parts (Gardner) Impact Resistance PF-4992 Test Method for Determining Cold Cracking of Flexible Plastic Materials

SAE J323

Impact Resistance Seat System Plastic Ornamentation ST-0005 Compression Compression and Recovery of Textile Materials FLTM BN-015-01 Compression and Recovery of Textile Materials FLTM BN-015-02 Compression Deflection GM6086M Flexible Cellular Polymeric Materials – Determination of Compression Set

ISO 1856

Rigid Cellular Plastics – Determination of Compression Properties

ISO 844

Compression Test of Urethane Foam Materials LP-463DB-5-03 Compression Set Resistance to LP-463KB-5-01 Die Shear Strength MIL-STD-883G Method 2019.7 Compression and Recovery of Insulation Padddings SAE J1352 Load Test SPP-GTP-2005 Density/Specific Gravity Density ASTM B328 Standard Test Methods for Specific Gravity (Relative Density) and Density of Plastics by Displacement

ASTM D792

Standard Test Methods for Apparent Density, Bulk Factor, and Pourability of Plastic Materials

ASTM D1895

Standard Test Method for Mass Per Unit Area (Weight) of Fabric

ASTM D3776

Determination of Mass per Area GMW3182 Plastics - Methods for Determining the Density of Non-Cellular Plastics

ISO 1183

Cellular Plastics And Rubbers - Determination of Apparent (Bulk) Density

ISO 845

Plastics- Methods for Determining the Density and Relative Density of Non-Cellular Plastics

JIS K 7112

Specific Gravity - Determination of – Friction Materials – Brake Linings

LP-463FB-02-01

Dimensional Stability Substrate Surface Appearance and Smoothness DVM-0006-PA Dimensional Stability-Interior Trim DVM-6394 Overall Appearance DY-0001 Dimensional Stability GMW4217 Cellular Plastics, Rigid – Test for Dimensional Stability ISO 2796 External Visual MIL-STD-883G-2009.9 Internal Visual (Monolithic) MIL-STD-883G-2010.11 Test Method for Determining Resistance to Fiber Loss, SAE J1530

TEST TEST METHOD

(A2LA Cert. No. 2743.01) Revised 02/28/2011 Page 8 of 24

Resistance to Abrasion and Bearding of Automotive Carpet Materials Test Method for determining Dimensional Stability of Automotive Textile Materials

SAE J883

Durability, Vibration & Operational Performance Specification for Instrumental Parts (General) 0094Z-SFA-9000 Nissan Design Specification - Nozzle-Def 27800NDS00 Nissan Design Specification - Duct-Vent 27860NDS00 Emblem (Rad Grille) (Nissan Design Specification) 62890NDS00 Vibration 65840NDS00 Specification for Inner Garnish Front/Rear Door Sash 7244Z-STKA-A000 Specification for Front Windshield Side Garn 7315ZS5A_0000_R4Y21094_E Specification for Front Inner Fender 7410Z-SDA-A000 Vibration Durability 7412Z-S9V-A010-M1 Handle Assembly, Tailgate Preliminary Specification 7481ZSZAAA000_SZAAF2387_E MLDG Set-Side (Nissan Design Specification) 76840NDS00 Mud Guard Set-Ctr (Nissan Design Specification) 76850NDS00 Light Aging, Friction Resistance, Scratch Resistance 7710Z-S2K-9000 Specification for ISNT Parts (General) 7710Z-SCC-9000 General Spec Inst. Parts 7710Z-SCC-9001 SEPA Spec Inst Panel 7710Z-SEP-A010-M1 TPU SKIN Specification for SEPA 7710Z-SEP-A210-M1 SEPA Seamless IP 7710Z-SEP-A810-M1 Instrument Panel Specification for SZAA 7710Z-SZAA-V000 DOC070529 Inst Panel Specification for TK4 7710ZTK4_A110M1 V/F TPO I/P Skin Specification for TK4 7710ZTK4_A210M1 Seamless I/P Specification for TK4 7710ZTK4_A910M1 Seamless I/P Specification for WZXA 7710Z-WZXA-R800 SOK Inst Panel 7711Z-SOK-A011-M1 AS Seamless SRS System Specification 7785Z-STX-A810-M1_C4624034_E AS Seamless Srs System Specification for STX 7785Z-STXA-A810-M1 Wheel Assy, Strg for SNA 7850ZSNA_N901_R4523058_E_ FIN-Door (Nissan Design Specification) 80900NDS00 Fabric Specification for Trim Cover, Seat 8102Z-SDAX-A500 Specification for Floor Carpet with Fiber Layer, Massback & Insulator

8330Z-STX-A010-M1

Specification for High Wear Center Console and Door Lining Armrests

8341Z-S84-A000

Spec for Assy LNG, Door/Side (General) 8350Z-SDA-9000 Specification for Assy LNG, Door/side (General) 8350Z-SNA-0000 Specification for Door LNG Assembly 8350Z-SNA-N000 Specification for PLR Garnish 8410Z-SJD-9000 Specification for Internal Collision Material 8412Z-S5A-A010-M1 Garnish Testing 8420Z-SLJ-0000 Specification for Assembly Trunk Parts (General) 8460Z-SEA-0000 Specification for RR Side LNG Assy, Preliminary Specification for SZAA

8461Z-SZAA-V000

American National Standard for Roadway Lighting Equipment – Luminaire Vibration

ANSI C136.31-2001

TEST TEST METHOD

(A2LA Cert. No. 2743.01) Revised 02/28/2011 Page 9 of 24

Standard Test Method for Random Vibration Testing of Shipping Containers

ASTM D4728-06

Vibration Testing Bellcore GR-63-CORE Instrument Panel and Console System DVM 0001-IP Squeak and Rattle DVM 0002-IP Other IP or Console Compartments/Components Cycle Life DVM 0019-IP Air Register Life Cycle DVM 0041-IP Cup Holder Life Cycle DVM-0004-IP Seat System Material Performance DVM-0005-ST Garnish Assembly DWG 74300-ASJCA-A020 Vibration, BSR DWG MA851317 (Mitsubishi) Global Door Latch System Component Technical Specification ES000003970-02 Mechanical Shock & Drop Test ES-6L2T-14540-AB, 5.31 Vibration ES-6L2T-14540-AB, 5.55 Lock Assembly Durability ES-84510 Performance Requirements for Exterior Plastic Parts (Do Not Use on New Applications. Being Replaced by GMW14650)

GM7452M

Adhesion and Durability of Exterior Trims GM9758P Interior Paint Finish Durability (Plastic Substrates) GMN10083 General Specification for Electrical/Electronic Component Analytical/Development/Validation (A/D/V) Procedures for Conformance to Vehicle Environmental, Reliability, and Performance Requirements

GMW3172

Test Method for Connectors HES D3127 Intier Closure Specification - Vibration Test ICS 000005173 Hood Latch Ajar Switch Specifications ICS 000007601 07 (GMX001) Side Door Module System ICS Z10296-E00 U222/228 and 354 Lightbar ICS Z10432 HB Power Cinch & Power Quick Release Liftgate Latch System ICS Z10450 (GMT920/930) Cargo Door Latches & Strikers ICS Z10463 ND Railway applications – Rolling stock equipment – Shock and vibration tests

IEC 61373

Test Fd: Random Vibration Wide Band -Reproducibility High IEC 68-2-34 Test Fc: Vibration (Sinusoidal) IEC 68-2-6 Test Fh: Vibration, Broadband Random (Digital Control) and Guidance

IEC 68-2-64

Operation Efforts IP-0022 Air Register Operating Efforts IP-0115 Vibration testing methods for automobile parts JIS D1601 Plasticized Polyvinyl Chloride Compounds JIS K6723 General Motors Lambda System Test Specification MCS E.S.000003970-02 Material Standard, Vinyl for Automobiles MES MN 401D Test Method for Fabrics, Carpets MES MN 405 Instrument Panel Common Standard MES PA 55000B Automobiles Parts Standard, Decoration Film (for Interior) MES PA 55219A Crash Pads MES PA 60350C Glove Lid Assy MES PA 64030B Automobiles Parts Standard, Consoles MES PA 64390A Operational Durability - Consoles MES PA 64410C Automobiles Parts Standard, Ashtrays MES PA 64610C

TEST TEST METHOD

(A2LA Cert. No. 2743.01) Revised 02/28/2011 Page 10 of 24

Interior/Exterior Plastic Parts for Decoration MES PW PT001C Vibration MIL-STD-202G-201A Vibration MIL-STD-202G-201A Vibration MIL-STD-810E-514.4 Altitude Test MIL-STD-810F-500.4 Vibration MIL-STD-810F-514.5 Acoustic Noise MIL-STD-810F-515.5 Shock MIL-STD-810F-516.5 Constant Acceleration MIL-STD-883E-2001.2 Mechanical Shock MIL-STD-883E-2002.3 Vibration- Variable Frequency MIL-STD-883E-2007.3 Washer System Windshield PF-10563 Air Outlet Assembly – Climate Control PF-10799 Window Regulators – Manual and Electric PF-10817 Cup Holder Assembly – Instrument Panel Mounted – Model Year 2007 and Beyond

PF-10915

Life Cycle Test PF-11014 Instrument Panel Component & System Buzz, Squeak, and Rattle/Vibration Requirements

PF-8243

Integral/Modular Door Latch and Power Door Lock Actuator Plus Latch Striker Assembly

PF-8684

Integral/Modular Door Latch & Power Door Actuator Plus Latch Striker Assembly

PF-8684-A

Door Inside Handle Specifications PF8926 Lint/Fiber Durability Test SOP 420-41-01 Reclining/Rearward Folding Seat Back Life Cycle ST-0051 Resonance Point Test TSE2512G Test Method for Strength and Durability of Door Armrests TSF7206G Durability Test Method for Shifting Hole Cover TSF7303G Test Method for Strength and Durability of Glove Compartment Door

TSF7304G

Test Method for Material Properties of Plastic Instrument Panel Assemblies

TSF7350G

Criteria for Opening and Closing Durability Test of Console Compartment Door

TSF7356G

Overload Test Method for Console Compartment Door TSF7357G Performance Test Methods for Push Type Ashtrays TSF7358G Durability Test Methods for Push Type Ashtrays TSF7359G Material Properties for Package Tray Trim TSF7360G Strength and Durability Test Method for Assist-Grip TSF7363G Test Method for Door Trim Material Characteristics TSF7754 G Test Method Regarding Material Properties for Pillar Garnishes TSF7755G Package Tray Trim Cover Materials TSL 3607G Criteria for Vibration Durability Test of Steering Wheel Assembly with Electrical Airbag

TSM6709G

Engineering Spec. A/C Duct VE-3W1H-19893-AA Intier Specified Vibration Testing Z10270 G00 Intier Specified Vibration Testing Z10296-E00 Intier Closure Specification - Vibration Test Z10365-C00 Inside Side Door Handle Specification For Gm Z10419

TEST TEST METHOD

(A2LA Cert. No. 2743.01) Revised 02/28/2011 Page 11 of 24

Inside Side Door Handle Specification for GM Z10419 Power Cinch & Power Quick Release Liftgate Latch System Z10450 ND Cargo Door Latches & Strikers Z10463 Environmental/Aging Heat Cycle Test Specification for Exterior Parts 0096Z-SYP-0000 Sunload Resistance 31826-SDS Heat Age Exposure 32163-SDS Heat Resistance to: 7710Z-S3VA-A010-M1 Specification for Carpet Light Resistance 8330Z-S9V-0000 Standard Practice for Xenon-Arc Exposure of Plastics Intended for Outdoor Applications

ASTM D2565

Standard Test Method for Thermal-Oxidative Stability of Polypropylene Using a Specimen Rotator Within an Oven

ASTM D3012

Standard Practice for Heat Ageing of Plastics Without Load ASTM D3045 Standard Practice for Fluorescent UV-Condensation Exposures of Paint and Related Coatings

ASTM D4587

Standard Test Method for Rubber Deterioration in Carbon—Arc Weathering Apparatus

ASTM D750

Environmental Exposure DVM -19195 Environmental Exposure DVM -19298 Performance (Thermal Cycling) for Plastic Parts DVM-0004-RG Thermal Shock Performance DVM-0019-OR Thermal Cycling DVM-004-RG Sunload Resistance DVM-31826 Heat Age Exposure DVM-32163 Accelerated Light Resistance ES-X33035 Accelerated Light Resistance ES-X60210 Accelerated Light Resistance ES-X83239 Thermal Shock Test for Paint Adhesion FLTM BI 107-05 Color Matching with Artificial Light FLTM BI 109-01 Fade (SAE J1885) Resistance of Materials to FLTM BN 101-01 Accelerated Exposure of Automotive Exterior Materials by Xenon Arc (SAE J1960)

FLTM BO 101-03

Environmental Test Cycles FLTM BQ 104-07 Resistance of Materials to Fade (SAE J1885) FLTM EU BN 001-01 Resistance to Artificial Weathering (Xenon Arc) FLTM EU BO 050-01 Adhesion Requirements of Bonded Interior Assemblies GM3602M Weatherstrips GM3803M Test for Thermal-Oxidative Stability Characteristics of Plastics GM9059P Procedures for Laboratory Accelerated Exposure of Automotive Materials

GM9125P

Accelerated Aging and Steaming GM9200P Procedure for Determining Heat Build-up of Insulating Material GM9202P Oven Aging Test Procedure for Painted Plastic Substrates GM9504P Automotive Environmental Cycles GM9505P Exterior Plastic Painted Parts Performance GM4497M Thermal Shock Test for Paint Adhesion GM9525P Environmental Cycling/Resistance to Temperature Cycling GMW14124 Colorfastness to Artificial Weathering GMW14162

TEST TEST METHOD

(A2LA Cert. No. 2743.01) Revised 02/28/2011 Page 12 of 24

Ageing GMW3232 Accelerated Test Method for Light Resistance with Xenon-Arc Lamp

HES D 6601

Basic Environmental Testing Procedures: Test M Low Air Pressure

IEC 68-2-13

Basic Environmental Testing Procedures IEC 68-2-38 Environmental Stability IP-0023 Heat Aging Performance (Type II Oven) ISO 188 Accelerated Aging Tests ISO 2440 Light-Exposure and Light-and-Water-Exposure Apparatus (Enclosed Carbon-Arc Type)

JIS B 7751

Light-Exposure and Light-and-Water-Exposure Apparatus (Xenon-Arc lamp type)

JIS B 7754

Test Method of Weatherability for Automotive parts JIS D 0205 Low Temperature Testing Methods for Rubber, Vulcanized or Thermoplastic

JIS K 6261

Plastics-Methods of Exposure to Laboratory Light Sources. Part 4: Open-flame carbon-arc lamps

JIS K 7350-4

Heat, Humidity and Cold Ageing Test for Adhesives LP 463CB-10-01 Weatherometer Test of Automotive Type Trim Materials LP 463KB-12-01 Fadeometer Test-Automotive Trim Materials LP 463KB-7-01 Heat Ageing of Trim Materials LP 463LB-13-01 Weather-Ometer Test LP 463PB-16-01 Fade-Ometer Test LP 463PB-17-01 Weather Resistance LP 463TB-2-01 Ice Freeze Resistance of Dual Durometer Weatherstrips LP-463AB-53-01 High Temperature MIL STD 810F-501.4 Low Temperature MIL STD 810F-502.4 Thermal Shock MIL-STD-202G-107G High Temperature Test MIL-STD-810E-501.3 Low Temperature MIL-STD-810E-502.3 High Temp Test MIL-STD-810F-501.4 Low Temp Test MIL-STD-810F-502.4 Temperature Shock MIL-STD-810F-503.4 Rain MIL-STD-810F-506.4 Humidity MIL-STD-810F-507.4 Sand and Dust MIL-STD-810F-510.4 Immersion MIL-STD-810F-512.4 Stabilization Bake MIL-STD-883E-1008.2 Temperature Cycling MIL-STD-883E-1010.7 Thermal Shock MIL-STD-883E-1011.9 Molded Plastic Parts – Interior Use MS-210-05 Methods of High Temperature Test for Passenger Compartment Synthetic Resin Parts

NES M0131

Methods of Thermal Cycle Test Method for Plastic Parts NES M0132 Weatherability and Light Resistance Test Methods for Synthetic Resin Parts

NES-M0135

Interior Automotive Plastic Part Testing. Dimensional Stability, At Service Temperature

SAE-J1717, B85

Accelerated Exposure of Automotive Interior Trim Components SAE-J1885

TEST TEST METHOD

(A2LA Cert. No. 2743.01) Revised 02/28/2011 Page 13 of 24

Using a Controlled Irradiance Water Cooled Xenon-Arc Apparatus Accelerated Exposure of Automotive Exterior Materials Using a Controlled Irradiance Water-Cooled Xenon Arc Apparatus

SAE-J1960

Accelerated Environmental Testing for Bonded Automotive Assemblies

SAE-J2100

Accelerated Exposure of Automotive Interior Trim Components Using a Controlled Irradiance Air-Cooled Xenon-Arc Apparatus

SAE J2212

Exposure of Automotive Exterior Materials Using A Controlled Irradiance Xenon-Arc Apparatus

SAE-J2527

Sunshine Carbon Arc TSH 1528G Carbon Arc Lamp Type Test Method for Accelerated Weather Resistance of Paint Films

TSH 1582G

Test Method for Light Transmittance of Paint Film TSH1520G Carbon Arc Lamp Type for Accelerated Weathering Resistance of Paint Film

TSH1582G

Xenon-Arc Lamp-Type Test Methods for Accelerated Weathering Resistance of Paint Film

TSH1585G

Acrylonitrile Butadiene Styrene Resin Molding Materials TSM-5512G Paint Performance, Plastic Substrates, Interior WSS-M2P188-A1 Flammability Standard Test Method for Rate of Burning and/or Extent and Time of Burning of Plastics in a Horizontal Position

ASTM D635

Flammability of Interior Material ES-X60410 Flammability Test for Automotive Materials FLTM BN 024-02 Flammability Test for Automotive Interior Materials FLTM EU BN 024-02 Flammability FMVSS 302 Flammability of Automotive Interior Materials-Horizontal Test Method

FMVSS 571.302

Flammability of Materials GM6090M Procedure for Testing Flammability of Materials GM9070P Test Method for Determining the Flammability of Interior Trim Materials

GMW3232

Flammability of Automotive Interior Materials HES C206 Flammability Test Method for Automotive Interior Materials HES D6003 Determination of Burning Behaviour of Interior Materials ISO 3795 Flammability of Automotive Interior Trim Material LP 463KC-13-01 Flammability of Interior Parts MES CF 050 Flammability for Interior Parts MES CF050D Flammability Resistance – Interior Materials MS-300-8 Test Method of Flammability of Interior Materials for Automobiles

NES M0094

Flammability of Polymeric Interior Materials – Horizontal Test Method

SAE J369

Flammability Test Method for Interior Non-Metallic Materials TSM 0500G Flammability for Non-Metallic Materials in Engine Compartment

TSM0504G

Test for Flammability of Plastic Materials for Parts in Devices and Appliances

UL 94

TEST TEST METHOD

(A2LA Cert. No. 2743.01) Revised 02/28/2011 Page 14 of 24

Fogging & Haze Standard Test Method for Specular Gloss ASTM D523 Standard Test Method for Haze and Luminous Transmittance of Transparent Plastics

ASTM D1003

Standard Test Method for Reflection Haze of High-Gloss Surfaces

ASTM D4039

Standard Test Method for Specular Gloss ASTM D523 Determination of the Windscreen Fogging Characteristics of Trim Materials in Motor Vehicles

DIN 75 201

Fogging Test FLTM EU BO 016-02 Sound Barrier Material - Interior GM2212; TSL 57056 Determination of Fogging Characteristics Of Automotive Interior Trim Materials

GM9305P

Fogging Characteristics of Trim Materials GMW3235 Test Method for Fogging of Interior Materials for Automobiles HES D 6508 Determination of Fogging Resistance of Interior Materials LP 463DB-12-01 Method of Fogging Test for Interior Materials NES M0161 Test Procedure to Determine the Fogging Characteristics of Interior Automotive Materials

SAE J1756

Fogging Test Method for Non-metallic Materials TSM 0503G Glass Haze TSM1564G General Plastics, Plastic Films & Rubber Tests Specification for BJ4H-HC Polypropylene Material 0094Z-S3V-A200 Specification for V/F TPO I/P Skin 7710ZSTX_A211M1_C4625320_E Specification for Preformed TPO V/F Composite 7710Z-STXA-A210-M1 New Flocking Specification for Molded Parts 8410Z-SE3-0001 Standard Test Method for Tear Resistance (Graves Tear) of Plastic Film and Sheeting

ASTM D1004

Standard Specification for Rubber Insulating Line Hose ASTM D1050 Standard Test Methods for Volatile Loss From Plastics Using Activated Carbon Methods

ASTM D1203

Standard Test Method for Rubber Property—Compression Set at Low Temperatures

ASTM D1229

Standard Test Method for Melt Flow Rates of Thermoplastics by Extrusion Plastometer

ASTM D1238

Standard Test Method for Resistance to Short-Time Hydraulic Pressure of Plastic Pipe, Tubing, and Fittings

ASTM D1599

Standard Test Method for Environmental Stress-Cracking of Ethylene Plastics

ASTM D1693

Standard Test Method for Apparent Viscosity of Plastisols and Organosols at Low Shear Rates

ASTM D1824

Standard Test Methods for Particle Size (Sieve Analysis) of Plastic Materials

ASTM D1921

Standard Test Method for Rubber Property—Durometer Hardness

ASTM D2240

Standard Test Method for Weight Loss of Plasticizers on Heating

ASTM D2288

TEST TEST METHOD

(A2LA Cert. No. 2743.01) Revised 02/28/2011 Page 15 of 24

Standard Test Method for Specular Gloss of Plastic Films and Solid Plastics

ASTM D2457

Standard Test Method for Ignition Loss of Cured Reinforced Resins

ASTM D2584

Standard Test Method for Rubber Property—Resilience by Vertical Rebound

ASTM D2632

Standard Test Method for Transition Temperatures and Enthalpies of Fusion and Crystallization of Polymers by Differential Scanning Calorimetry

ASTM D3418

Standard Test Methods for Rubber—Identification by Infrared Spectrophotometry

ASTM D3677

Standard Test Methods for Rubber Hose ASTM D380 Standard Test Methods for Rubber Property—Compression Set ASTM D395 Standard Test Methods for Vulcanized Rubber and Thermoplastic Elastomers— Tension

ASTM D412

Standard Test Method for Rubber Property—Effect of Liquids ASTM D471 Standard Test Method for Rubber—Deterioration in an Air Oven

ASTM D573

Rubber Properties in Compression ASTM D575 Standard Test Method for Tear Strength of Conventional Vulcanized Rubber and Thermoplastic Elastomers

ASTM D624

Standard Test Method for Determination of Moisture in Plastics by Loss in Weight

ASTM D6980

Shrinkage from Mold Dimensions of Molded Plastics ASTM D955 Standard Practices for General Techniques of Infrared Quantitative Analysis

ASTM E168

Standard Test Method for Compositional Analysis by Thermogravimetry

ASTM E1131

Standard Test Methods for Creep Relaxation of a Gasket Material

ASTM F38

Trapezoid Tear Strength FLTM BN 022-01 Material Specification Plastic - Plastic Parts GM7400M Glass Content of Reinforced Plastics GM9077P PP Resins for Automobiles HES C 252 General Test Methods for Resin Materials for Vehicles HES D2500-99A Test Methods for PP Resin Materials for Interior of Automobiles

HES D2502-02

Determination of the Melt Mass-Flow Rate (MFR) and the Melt Volume-Flow Rate (MVR) of Thermoplastics

ISO 1133

Plastics – Thermogravimetry (TG) of Polymers ISO 11358-1 & -2 Cellular plastics - Polyethylene-Methods of Test ISO 7214 Flexible cellular polymeric materials - Determination of tear strength

ISO 8067

Rubber, Vulcanized - Determination of Low-Temperature Brittleness

ISO 812

Permanent Set Testing Methods for Rubber, Vulcanized or Thermoplastic

JIS K 6262

Testing Method for Polyethylene Foams JIS K 6767 Plastics-Film and Sheeting-Determination of Tear Resistance – Part 1: Trouser Tear Method

JIS K 7128

TEST TEST METHOD

(A2LA Cert. No. 2743.01) Revised 02/28/2011 Page 16 of 24

Physical testing methods for Vulcanized Rubber JIS K6301 Polyethylene Films for Packaging JIS Z 1702 Heat Shrinkage Plastic Films for Packaging JIS Z 1709 Molding Retention MTL 4333 Thermoplastic Olefin Seat for Automobiles NES M7108 Testing Methods of Physical Property for Thermoplastics NES M8020 Mold Shrinkage of Injection Molded Thermoplastics SAE J1639 Interior Automotive Plastic Part Testing SAE J1717 Test Method for Measuring Mass (Weight) of Organic Trim Materials

SAE J860

Resin Content TI 134 Test Method Regarding to Material Properties for Plastic Consoles

TSF7354G

Test Method for Regarding Material Properties for Plastic and Polyurethane Bumper Covers and Front Spoilers

TSF1354G

Test Method Regarding Material Properties for Plastic Engine Under Cover

TSF2251G

Test Method for Material Properties of Plastic Scuff Plates TSF2254G Test Methods Regarding Material Properties of Plastic Louver Cowl Top Ventilators

TSF2256G

Test Method Regarding Material Properties of Plastic Material for Radiator Grilles

TSF3253G

Test Method Regarding Material Properties for Plastic Side Mud Guards

TSF3256G

Test Methods for Material Properties of Mud Guards TSF3550G Test Method Regarding Material Properties for Plastic Assist Grips

TSF7204G

Test Method for Material Properties of Plastic Finish Panels of Instrument Cluster

TSF7351G

Silencer Pad Materials TSL3505G General Test Methods for Vinyl Leathers TSL5100G General Test Method Regarding Material Properties for Plastic Parts

TSM 0502G

Standard Test Methods for Plastic Molding Materials TSM0501G General Test Method Regarding Material Properties for Plastic Parts

TSM0502G

Standard Test Methods for Plastic Molding Materials for Compliance with ISO

TSM0506G

Polypropylene Resin Molding Materials TSM5514G Polyacetal Resin Molding Materials TSM5515G Polyethylene Resin Molding Material TSM5518G Acrylonitryle X Styrene Resin Molding Materials TSM5523G Composite Reinforced Polypropylene Molding Materials TSM5601G Super Olefin Polymer Molding Materials (TSOP) TSM5608G Polypropylene Foam Resin Molding Materials for Energy Absorber for Bumper

TSM5725G

Polyethylene Films TSM7500G Indication Method of Material Marking for Plastic Parts and Rubber Parts

TSZ6005G

TEST TEST METHOD

(A2LA Cert. No. 2743.01) Revised 02/28/2011 Page 17 of 24

Hardness Standard Test Method for Rubber Property—International Hardness

ASTM D1415

Standard Test Methods for Indentation Hardness of Organic Coatings

ASTM D1474

Standard Test Method for Rockwell Hardness of Plastics and Electrical Insulating Materials

ASTM D785

Standard Hardness Conversion Tables for Metals Relationship Among Brinell Hardness, Vickers Hardness, Rockwell Hardness, Superficial Hardness, Knoop Hardness, and Scleroscope Hardness

ASTM E140

Standard Test Method for Microindentation Hardness of Materials

ASTM E384

Standard Test Method for Vickers Hardness of Metallic Materials

ASTM E92

Pencil Hardness of Paint Films FLTM BI 151-01 Material and Performance Requirements for Metroc and Customary Series Case Hardened Tapping Screws

GM6010M

Hardness Test and Hardness Number Conversions GM9053P Microhardness Testing GM9054P Determination of Hardness (Indentation) ISO 2439 Flexible Cellular Polymeric Materials - Determination of Hardness (Indentation Technique)

ISO 868

Hardness Testing Methods for Rubber, Vulcanized or Thermoplastic

JIS K 6253

Pencil Hardness Test LP 463PA-2-01 Metric Thread Rolling Screws SAE J1237 Hardness Tests and Hardness Number Conversions SAE J417 Test Method for Hardness of Paint Film TSH1500G Humidity Humidity Ageing 32067-SDS Standard Practice for Test Water Resistance of Coatings in 100% Relative Humidity

ASTM D2247

Humidity Aging for Tape Attachments DVM-19297 Condensing Water Vapor Test FLTM BI 104-02 Water Fog Humidity Test GM4465P Mildew Growth GM9128P Procedures for High Humidity Test GMW14729 Basic Environmental Testing Procedures: Test Z/AD Composite Temperature /Humidity Cyclic Test

IEC 68-2-38

Humidity Cabinet Test LP 461H-15 Resistance to Humidity, Hot, and Cold Cycling of Trim Materials Test

LP 463LB-12-01

Humidity Exposure LP 463PB-09-01 Humidity (Steady State) MIL-STD202F-103B Instrumented & Non-Instrumented Colour Color Differences of Opaque Materials Visual Evaluation of ASTM D1729

TEST TEST METHOD

(A2LA Cert. No. 2743.01) Revised 02/28/2011 Page 18 of 24

Diffusely-Illuminated Opaque Materials Standard Practise for Calculation of Color Tolerances and Color Differences From Instrumentally Measured Color Coordinate

ASTM D2244

Grey Scale for Assessing Change in Colour JIS L 0804 General Principles of Testing Methods for Colour Fastness JIS L0801 Resistance to Dye Transfer (Water Dye Test) LP-463KC-1-01 Instrumental Color Difference Measurement for Exterior Finishes, Textiles and Colored Trim

SAE J1545

Criteria for Test for Quality of Color Change by Ageing TSL 0601G Metallic Ores and Products (All Forms, Articles of Metal) Standard Test Method for Evaluating the Microstructure of Graphite in Iron Castings

ASTM A247

Standard Test Methods and Definitions for Mechanical Testing of Steel Products

ASTM A370

Standard Guide for Defining and Rating the Microstructure of High Carbon Bearing Steels

ASTM A892

Standard Test Method for Weight [Mass] of Coating on Iron and Steel Articles with Zinc or Zinc-Alloy Coatings

ASTM A90

Test Method for Estimating the Depth of Decarburization of Steel Specimens

ASTM E1077

Standard Test Methods for Determining Average Grain Size ASTM E112 Standard Test Methods for Rockwell Hardness of Metallic Materials

ASTM E18

Standard Test Methods for Determining the Inclusion Content of Steel

ASTM E45

Standard Test Methods for Tension Testing of Metallic Materials

ASTM E8

Standard Test Methods for Estimating the Largest Grain Observed in a Metallographic Section (ALA Grain Size)

ASTM E930

Metallic Sheet, Mechanical Properties Testing GMW3335 Chromate Conversion Coatings on Zinc, Cadmium, Aluminum-Zinc Alloys and Zinc-Aluminum Alloys - Test Methods

ISO 3613

General Rules for Inspection of Steel JIS G 0303 Alloy Tool Steels JIS G 4404 Hot-Rolled Carbon Steel Sheets and Strip MES MM 100A Cold-Rolled High Tensile Strength Steel Plates, Sheets and Strip

MES MM 106A

Hardemability Bands for Carbon and Alloy H Steels SAE J1268 Miscellaneous Specification for Curlfit Panel 7729Z-S5A-0000 Genuine Leather (Chrome Free) for Trim Cover, Seat 8102Z-SEP-A000 Specification for New Light Felt 8330Z-SV4-J010-M1 Standard Test Method for Boiling Point of Engine Coolants ASTM D1120 Standard Test Method for Flash Point by Tag Closed Cup Tester ASTM D56 Standard Test Method for Thickness of Highloft Nonwoven Fabrics

ASTM D5736

Standard Practices for General Techniques of Infrared Quantitative Analysis

ASTM E168

TEST TEST METHOD

(A2LA Cert. No. 2743.01) Revised 02/28/2011 Page 19 of 24

Surface Friction DVM-0011-BPv3 Wax Build-Up on Grained Surfaces DVM-0013-OR Test for Contaminants in Textile Material FLTM AN 101-03 Determination of the Surface Roughness of Cold Rolled Sheet Steel

FLTM BA 003-01

Under-Vehicle and Under-Hood Component Rating Scale GM8101G Dust-Out From Fiber Sound Absorber Pad GM9635P Procedure for Determining Fiber Degradation of Automotive Textiles

GM9771P

Determination of Resistance to Mildew Growth GMW3259 General Test Methods For Fabrics HES D6506-00 Environmental Testing – Part 2: Dust Test, Free Settling Dust, Test L Dust and Sand

IEC 68-2-68, 1994

Hydraulic Fluid Power - Fluids - Method for Coding the Level of Contamination by Solid Particles

ISO 4406

General Rules of Dust Test for Automobile Parts JIS D 0207 Test Powders and Test Particles JIS Z 8901 Friction Index LP 463AB-52-01 Substance Use Restrictions NES M0301 Felt for Automobiles NES M7101 Low Voltage Primary Cable SAE J1128 Zinc-Composite Silicon-Based Resin Coating (Hexavalent Chrome-Free)

TSH7702G

Silencer Pad Materials TSL 3505G Standard Test Methods for Woven Fabrics and Knitted Fabrics TSL2100G Fabrics for Trims and Console Doors TSL2613G General Test Methods for Boards TSL3101G Hardboards TSL3503G Sound-Absorbing Materials in Engine Compartment TSL3608G (Except Section 4.11) Safety Pad Materials with Vacuum-Formed Outer Layer TSM6700G Odor and Volatile and Semi-Volatile Organic Compounds (VOC and SVOC) Emissions Specification for test method for VOC 0094Z-SNA-0000 Standard Test Method for Volatile Content of Coatings ASTM D2369 Hot Odor Test for Insulation Materials CPNM-LOS-ST-10-06-07-E Odor Test CPNM-MOS-ST-10-04-08-E Determination and Assessment of Odor From Interior Trim Materials/Composites/Assemblies

FLTM BO 131-01

Interior Odor Test FLTM BO 131-03 Determination of Volatile and Semi-Volatile Organic Compounds from Vehicle Interior Materials

GMW15634

Test Method for Determining the Resistance to Odor Propagation of Interior Materials

GMW3205

Static Headspace GC-MS for Interior Materials Interior Emissions

GMW8081

Odor Test for Materials or Material Assemblies LP 463KC-09-01 Test Method of Odor for Interior Materials MS-300-34 Method of Testing the Smell of Interior Parts NES M0160 Hot Odor Test for Insulation Material SAE J1351 Volatile Component Measurement Method Using Sampling Bag TSM0508G

TEST TEST METHOD

(A2LA Cert. No. 2743.01) Revised 02/28/2011 Page 20 of 24

(VOC) Measuring Volatile Substances Under Heat Desorption Method TSM0509G Smell Quality of Non-Metallic Materials TSM0505G Control Method for Substances of Environmental Concern TSZ0001G Test Method for Analyzing Content of Substances of Environmental Concern in Automotive Materials and Parts

TSZ0003G

Polyurethane (PUR) Foam, High Resilient WSB-M2D402-A3 Paints, Coatings & Plating Systems Specification for Paintable High Modulus Bumper Facia Material

0094Z-SJC-A210-M1

Quality of Coating for Interior Resin Parts 0096Z-SEC-A000 Quality of Coating for Interior Resin Parts 0096Z-SEC-A000 Quality of Coating on Resin Exterior Parts 0096Z-SIE-E000 Polycarbonated Door Outer Handle Coating Specification 7214ZST7 0000 R4P21051E Specification for Front Windshield Side Garnish 7315ZS5A 0000 R4Y21094E Standard Test Method for Measurement of Coating Mass per Unit Area on Anodically Coated Aluminum

ASTM B137-95

Standard Specification for Electrodeposited Coating of Copper Plus Nickel Plus Chromium and Nickel Plus Chromium

ASTM B456

Standard Test Method for Measurement of Metal and Oxide Thickness by Microscopical Examination of Cross Section

ASTM B487

Coating Thickness by the Magnetic Method: Nonmagnetic Coatings on Magnetic Base Materials

ASTM B499

Standard Test Method for Measurement of Thickness of Metallic Coatings by the Coulometric Method

ASTM B504

Standard POractice for Qualitative Adhesion Testing of Metallic Coatings

ASTM B571

Standard Guide for Measuring Thickness of Metallic & Inorganic Coating

ASTM B659

Standard Test Method for Simultaneous Thickness and Electrode Potential Determination of Individual Layers in Multilayer Nickel Deposit (STEP Test)

ASTM B764

Method for Non-destructive Measurement of Dry Film Thickness of Nonmagnetic Coatings Applied to a Ferrous Base

ASTM D1186

Dry Film Thickness of Non-Conductive Coatings Applied to a Nonferrous Metal Base

ASTM D1400

Standard Practice for Testing Water Resistance of Coating Using Water Fog Apparatus

ASTM D1735

Standard Test Method for Chipping Resistance of Coatings ASTM D3170 Standard Test Method for Film Hardness by Pencil Test ASTM D3363 Standard Practice for Measurement of Wet Film Thickness by Notch Gages

ASTM D4414

Standard Test Method for Evaluating Degree of Blistering of Paints

ASTM D714

Water Resistance Test for Exterior Paint DVM-0026-PA Exterior Paint System Chip Resistance - Grit Blast Method DVM-0039-PA Exterior Paint System Chip Resistance- Gravelometer Method DVM-0040-PA Exterior Clearcoat - Scratch Resistance on Rigid Substrates DVM-0058-PA Exterior Paint Acid Etch Resistance DVM-5861

TEST TEST METHOD

(A2LA Cert. No. 2743.01) Revised 02/28/2011 Page 21 of 24

Coating Quality Standard of ABS Resin Exterior Parts DWG 0096Z-SM4-0000 Quality of TPU Plastic Exterior Brilliant Flexible Paint DWG 096Z-S5N-C000 Chip Resistance Test for Painted Panels FLTM BI 007-01 Water Immersion Test for Painted Parts and Panels FLTM BI 104-01 Paint Adhesion Test FLTM BI 106-01 Measurement of the Gloss of Paint Panels FLTM BI 110-01 Thickness Measurement of Paint Films FLTM BI 117-01 Chip Resistance Test for Painted Panels FLTM BI 157-05 High Performance Chip Resistance Test New Rating Scale FLTM BI 157-06 Mar Resistance Determination for Automotive Coatings FLTM BI 161-01 Plastic and Tapes Resistance to Protective Waxes and Dewaxing Materials

FLTM BO 155-01

Stone Chip Resistance Test FLTM EU BI 057-02 Measuring Thickness of Electrodeposits and Anodic Coatings GM4260P Decorative Chromium Plating - Copper, Nickel, Chromium Type

GM4372M; GM4373M; GM4374M

Chip Resistance of Coatings GM9508P Colorfastness to Crocking (Rubbing) GM9033P Tape Adhesion for Paint Finishes GM9071P Dime Scrape Test to Determine Paint Adhesion and Brittleness GM9506P Thumbnail Hardness Test for Painted Parts GM9507P Abrasion Resistance of Organic Coatings (Taber Abraser Method)

GM9515P

Cleaning/Solvent Resistance of Automotive Components During Normal Customer Use

GM9900P

Minimum Performance Requirements for Decorative Chromium Plated Plastic Parts

GMW14668

Stone Impact Resistance of Coatings GMW14700 Plastic Painted Parts Performance Requirements GMW14797 Tape Adhesion Test for Paint Finishes GMW14829 Thermal Shock Test for Paint Adhesion GMW15919 Corrosion-Proof Coating (On Metals) HES D 2021-07 General Test Method for Coating HES D 6501-06 Electroplating (for Corrosion Prevention, Rust Prevention and Decoration)

HES D2003-04

General Coating (On Resins) HES D2018.99 General Test Method for Plating HES D6001, 4.2 General Test Methods for Plating HES D6001-04A Chipping Resistance HES D6500 Test Method for Paint Finish ISC-E00-006 Determination of Loss on Ignition ISO 1172 Metallic and Oxide Coatings – Measurement of Coating Thickness – Microscopical Method

ISO 1463

Paints and Varnishes – Determination of Film Thickness ISO 2808 Testing Method for Paints JIS K 5400 Testing Methods for Paints- Mechanical Property, Scratch Hardness (Stylus Method)

JIS K 5600-5-5

Cycle Testing of Painted Surfaces LP 463PB-22-01 Chip Resistance on Surface Coatings LP 463PB-39-01 Paint Film MES MN 600H

TEST TEST METHOD

(A2LA Cert. No. 2743.01) Revised 02/28/2011 Page 22 of 24

Test Method for Paint Film MES MN 601G Paint – Multi-Purpose for Interior Parts – Solvent or Waterborne MS-PD-48-1 Testing Method for Automotive Paint NES M 0007 Methods of Test for Coating of Synthetic Resin NES M0141 Paint Film Quality of Plastic Parts and Chrome Plated Parts NES M5081 Exterior Paint Acid Etch Resistance PA-0145 Test for Chip Resistance of Surface Coatings SAE J400 Test Method for Electrodeposition Film Properties TSH 1551G Coating Quality of Paints for Plastic Parts TSH 3111G Paint Quality for Interior Parts TSH 3130G Electroplated Zinc Coating TSH 6500G Test Method for Print Resistance of Paint Film TSH1501G Test Method for Adhesive Property of Paint Film TSH1503G Test Method for Flexibility of Paint Film TSH1504G Test Method for Water Resistance of Paint Film TSH1505G Test Method for Volatile Solvent Resistance of Paint Film TSH1508G Test Method for Chemical Resistance of Paint Film TSH1509G Test Method for Gloss of Paint Film TSH1519G Test Method for Light Transmittance of Paint Film TSH1520G Test Method for Hardness of Paint Film TSH1539G Test Method for Nail Scratch Resistance of Paint Film TSH1544G Coating Quality of Exterior Parts TSH3131G Paint Performance, Rigid Substrates, Exterior WSS-M2P180-A (Except 4.3) Paint Performance, Flexible Substrates, Exterior WSS-M2P181-A (Except 4.3) Salt Spray, CASS & Cyclic Corrosion Standard Practice for Operating Salt Spray (Fog) Apparatus ASTM B117 Standard Test Method for Copper-Acceleratied Acetic Acid-Salt Spray (Fog) Testing (CASS)

ASTM B368

Standard Test Method for Copper-Acceleratied Acetic Acid-Salt Spray (Fog) Testing (CASS)

ASTM B368

Standard Test Method for Evaluation of Pzainted or Coated Specimens Subjected to Corrosive Environments

ASTM D1654

Simulated Corrosion Lifetime - Salt Spray DVM -0002-BM Fan Cyclic Corrosion Test DVM 0066-CF Corrosion DVM-0008 Exterior Lighting DVM - Salt Spray DVM-0014-EX Salt Spray Resistance Test for Painted Panels and Parts FLTM BI 103-01 Painted Sheet Metal Corrosion Test FLTM BI 123-01 Component Corrosion Test FLTM BI 123-03 Acid Dissolution Test for Decorative Aluminum Parts FLTM BQ 007-02 Copper-Accelerated Acetic Acid-Salt Spray Testing (CASS Test)

FLTM BQ 105-01

CASS Test – Copper Accelerated Acetic Acid Salt Spray Test GM4476P Corrosion Creepback Test Method GM9102P Scab Corrosion Creepback of Paint on Metal Substrate GM9511P Accelerated Corrosion Test GM9540P Salt Spray Test GM4298P Procedure for Copper-Accelerated Acetic Acid Salt Spray (CASS) Test

GMW14458

TEST TEST METHOD

(A2LA Cert. No. 2743.01) Revised 02/28/2011 Page 23 of 24

Cyclic Corrosion Laboratory Test GMW14872 Corrosion-Proof Coating (On Metals) HES D 2021-07 Electroplating (For Corrosion Prevention, Rust Prevention and Decoration)

HES D2003

Test Ka: Salt Mist IEC 68-2-11 Test Kb: Salt Mist, Cyclic (Sodium Chloride Solution) IEC 68-2-52 Corrosion Resistance for Plated Parts ISC-E00-005-5.1 Corrosion tests in artificial atmospheres – Salt spray tests ISO 9227 Method of Moisture Rain & Spray Test for Automobile Parts JIS D 0203 Methods of Salt Spray Testing JIS Z2371 Salt Spray (Corrosion) MIL-STD202F-101D Salt Fog MIL-STD-810F-509.4 Methods of CASS Testing NES M0138-91 Salt Spray Testing NES M0140 Guidelines for Laboratory Cyclic Corrosion Test Procedures for Painted Automotive Parts

SAE J1563

Laboratory Cyclic Corrosion Test SAE J2334 Test Method of Salt Spray TSH 1552G Tensile Properties Standard Test Method for Breaking Strength and Elongation of Textile Fabrics (Grab Test)

ASTM 5034

Standard Guide for Evaluating Nonwoven Fabrics ASTM D1117 Standard Test Method for Tensile Properties of Plastics by Use of Microtensile Specimens

ASTM D1708

Standard Test Method for Tensile-Impact Energy to Break Plastics and Electrical Insulating Materials

ASTM D1822

Standard Test Method for Tearing Strength of Fabrics by the Tongue (Single Rip) Procedure (Constant-Rate-of-Extension Tensile Testing Machine)

ASTM D2261

Standard Test Methods for Tensile, Compressive, and Flexural Creep and Creep-Rupture of Plastics

ASTM D2990

Standard Test Method for Breaking Strength and Elongation of Textile Fabrics (Grab Test)

ASTM D5034

Standard Test Method for Tearing Strength of Nonwoven Fabrics by the Trapezoid Procedure

ASTM D5733

Standard Test Method for Tensile Properties of Plastics ASTM D638 Standard Test Method for Tensile Properties of Thin Plastic Sheeting

ASTM D882

Standard Test Methods for Tension Testing of Nonmetallic Gasket Materials

ASTM F152

Tensile Adhesion of Adhesively Attached Ext. Ornamentation DVM -18401 Flexible cellular polymeric materials - Determination of Tensile Strength and Elongation at Break

ISO 1798

Rigid cellular plastics - Determination of Tensile Properties ISO 1926 Rubber, vulcanized or thermoplastic – Determination of tensile stress-strain properties

ISO 37

Plastics - Determination of Tensile Properties ISO 527-1/2 Physical testing methods for vulcanized rubber JIS K 6301 Rubber, Vulcanized or Thermoplastic - Determination of JIS K6251

TEST TEST METHOD

(A2LA Cert. No. 2743.01) Revised 02/28/2011 Page 24 of 24

Tensile Stress - Strain Properties Rubber, Vulcanized or Thermoplastic - Determination of Tear Strength

JIS K6252

Test Pieces for Tensile Test for Metallic Materials JIS Z 2201 Method of Tensile Test for Metallic Materials JIS Z 2241 Tensile Strength – Determination of (Tape or Film) LP 463TB-4-01 Passive Sphere Tension Test TP-10110 Water Immersion & Absorption Standard Test Method for Water Absorption of Core Materials for Structural Sandwich Constructions

ASTM C272

Standard Test Method for Water Absorption of Rigid Cellular Plastics

ASTM D2842

Water Resistance Using Controlled Condensation ASTM D4585 Standard Test Method for Water Absorption of Plastics ASTM D570 Standard Practice for Testing Water Resistance of Coatings Using Water Immersion

ASTM D870

Water Ingress BS EN 60529, Sect. 14.2.1, IPX1 Water Ingress BS EN 60529, Sect. 14.2.2, IPX2 Water Resistance Test for Exterior Paint DVM-0026-PA Degrees of protection provided by enclosures (IP Code) IEC 60529 Rigid cellular plastics - Determination of Water Absorption ISO 2896 Moisture Resistance MIL-STD-202F-106F Moisture Resistance MIL-STD-883E-1004.7 Test Method for Wicking of Automotive Fabrics and Fibrous Materials

SAE J1913

A2LA has accredited

SCI-LAB MATERIALS TESTING, INC. Kitchener, Ontario, CANADA

for technical competence in the field of

Mechanical Testing

This laboratory is accredited in accordance with the recognized International Standard ISO/IEC 17025:2005 General Requirements for the Competence of Testing and Calibration Laboratories. This accreditation demonstrates technical competence for a defined scope and the

operation of a laboratory quality management system (refer to joint ISO-ILAC-IAF Communiqué dated 8 January 2009).

Presented this 16th day of March 2009.

_______________________ President & CEO For the Accreditation Council Certificate Number 2743.01 Valid to March 31, 2011 Revised February 28, 2011

For the tests or types of tests to which this accreditation applies, please refer to the laboratory’s Mechanical Scope of Accreditation.