Daftar Pustaka
Alipcilar, H. K. dan Ulfaz, A. C., (2000), Synthesis of Submicron Silicalite-1 Crystals from
Clear Solutions, Cryst. Res. Technol., 35 (8), 933–942
Aubert, E., et al, (2002), Location of Fluoride Counterion in As-Synthesized Silicalite-1 by
Single Crystal X-ray Diffraction, J. Phys. Chem. B, 106, 1110-1117
Breck, D. W., (1974), Zeolite Molecular Sieves: Structure, Chemistry and Use, John Wiley
and Sons, Inc., New York, 1-50
Gamboa, A., The Theory and Instrumentation of the Atomic Absorption Spectrophotometer,
http://www.physicspost.com, diakses (7 Maret 2008)
German, R. M., (1996), Sintering Theory and Practice, John Wiley & Sons, Inc., New York,
1-224
Guth, J. L., et al, (1986), in Stud. Surf. Sci. Catal., Vol. 28, Y. Murakami, A. Iijima, J. W.
Ward (eds.), Kodansha-Elsevier, Tokyo, 121
Krishna, R. dan Paschek, D., (2001), Molecular simulations of adsorption and siting of light
alkanes in silicalite-1, Phy. Chem. Chem. Phy., 1
Lee, S. and Shantz, D. F., (2005), High temperature synthesis of silicalite-1 in cationic
Microemulsions, Microporous and Mesoporous Materials, 86, 268–276
Li, L., et al, (2007), Enhanced Water Permeation of Reverse Osmosis through MFI-Type
Zeolite Membranes with High Aluminum Contents, Ind. Eng. Chem. Res., 46, 1584-1589
Masuda, T., et al, (2003), Preparation of hydrophilic and acid-proof silicalite-1 zeolite
membrane and its application to selective separation of water from water solutions of
concentrated acetic acid by pervaporation, Separation and Purification Technology, 32, 181-
189
Mulder, M., (1996), Basic Principles of membrane Technology, edisi kedua, Kluwer
Academic Publisher, Netherlands, 1-286
40
Muller, U., (1992), Inorganic Structural Chemistry, John Wiley & Sons, Inc., New York,
177
Nelson, S. A., (2006), Weathering & Clay Minerals, http://www.tulane.edu, diakses (7 Maret
2008)
Center for Studies of Origins of Life, Rensselaer Polytechnic Inst.,
http://www.origins.rpi.edu, diakses (7 Maret 2008)
Priyono, J., Refleksi Hari Air Sedunia 2007: Mengatasi Kelangkaan Air,
http://www.sutikno.org, diakses (1 September 2007)
Radiological & Environmental Management, (2006), Scanning Electron Microscope,
http://www.purdue.edu, diakses (7 Maret 2008)
Sibarani, S. O., (1994), Skripsi, Institut Teknologi Bandung, Bandung
Subkhi, U., (1999), Skripsi, Institut Teknologi Bandung, Bandung
Sutandi, A. S., (1995), Skripsi, Institut Teknologi Bandung, Bandung
Stylianou, M. A., (2007), Removal of Cu(II) in fixed bed and batch reactors using natural
zeolite and exfoliated vermiculite as adsorbents, Desalination, 215, 133–142
Tosheva, L., (1999), Tesis, Luleå University of Technology, Luleå, 1
West, A. R., (1984), Solid State Chemistry and Its Application, John Wiley & Sons, Inc.,
New York, 1-358
Wingenfelder, U., et al, (2005), Removal of Heavy Metals from Mine Waters by Natural
Zeolites, Environ. Sci. Technol., 39, 4606-4613
Lampiran A Difraktogram
A.1 Serbuk bentonit
Pos. [°2Th.] Tinggi [cts] FWHM [°2Th.] d [Å] Int. Rel. [%] Lebar tip [°2Th.]5,7699 337,10 0,5712 15,30488 84,04 0,6854
12,2149 75,25 0,6528 7,24010 18,76 0,7834 19,8217 231,81 0,4080 4,47546 57,79 0,4896 25,0694 59,59 0,6528 3,54926 14,86 0,7834 26,5880 401,14 0,3264 3,34988 100,00 0,3917 34,9314 114,43 0,9792 2,56651 28,53 1,1750 38,3598 99,84 0,3264 2,34465 24,89 0,3917 39,3426 42,86 0,4896 2,28831 10,68 0,5875 44,5271 175,06 0,3264 2,03316 43,64 0,3917 45,7557 65,37 0,3264 1,98138 16,30 0,3917 50,1363 60,70 0,4080 1,81805 15,13 0,4896 59,8877 41,19 0,4896 1,54322 10,27 0,5875 62,3228 74,21 0,7344 1,48864 18,50 0,8813 67,9758 32,34 0,9792 1,37795 8,06 1,1750 73,5622 29,09 0,9792 1,28649 7,25 1,1750 75,6708 116,17 0,3264 1,25580 28,96 0,3917 79,7970 29,50 0,4896 1,20091 7,35 0,5875
42
A.2 Silicalite-1 hasil sintesis dan literatur
Pos. [°2Th.] Tinggi [cts] FWHM [°2Th.] d [Å] Int. Rel [%] Lebar tip [°2Th.]7,8093 254,66 0,3264 11,31193 46,70 0,3917 8,6972 196,76 0,4080 10,15897 36,08 0,4896
14,6823 74,58 0,4080 6,02848 13,68 0,4896 15,6199 26,82 0,4896 5,66864 4,92 0,5875 17,5844 31,83 0,6528 5,03952 5,84 0,7834 20,8790 60,46 1,1424 4,25116 11,09 1,3709 22,9557 545,36 0,4896 3,87106 100,00 0,5875 23,7412 278,13 0,3264 3,74473 51,00 0,3917 24,2983 127,13 0,3264 3,66012 23,31 0,3917 26,7260 47,16 0,9792 3,33290 8,65 1,1750 29,7146 86,21 0,4080 3,00414 15,81 0,4896 30,8386 42,11 0,3264 2,89716 7,72 0,3917 35,8948 28,25 0,6528 2,49981 5,18 0,7834 37,2203 31,25 0,6528 2,41377 5,73 0,7834 38,1966 52,74 0,4896 2,35429 9,67 0,5875 44,5169 136,93 0,3264 2,03360 25,11 0,3917 45,3614 88,02 0,3264 1,99769 16,14 0,3917 47,2985 16,30 0,4080 1,92029 2,99 0,4896 48,3810 14,59 0,4896 1,87983 2,68 0,5875 49,8524 24,02 0,6528 1,82773 4,41 0,7834 54,7661 28,67 0,4896 1,67479 5,26 0,5875 72,5686 70,43 0,5712 1,30164 12,91 0,6854 78,1375 28,21 0,3264 1,22221 5,17 0,3917 88,0962 28,36 0,4896 1,10793 5,20 0,5875
hasil sintesis
43
44
A.3 Perbandingan antara difraktogram serbuk bentonit dan material pendukung membran bentonit
Serbuk bentonit
No. Pos. [o2Th.] Int. [%] d [Å] Lebar [o2Th.] I/I0
1. 12,42 22 7,121 1,02 65 2. 19,88 33 4,462 0,90 98 3. 25,00 25 3,558 0,90 74 4. 26,68 29 3,338 0,78 86 5. 34,98 17 2,563 1,05 50 6. 36,58 16 2,454 0,60 47 7. 41,14 10 2,192 0,69 30 8. 50,24 8 1,814 0,63 24 9. 62,44 9 1,486 1,26 27
Material pendukung membran bentonit
No. Pos. [o2Th.] Int. [%] d [Å] Lebar [o2Th.] I/I0
1. 20,88 23 4,250 0,81 58 2. 26,62 39 3,345 0,81 98 3. 33,14 13 2,701 0,90 33 4. 35,72 10 2,511 0,66 25 5. 36,62 10 2,451 0,60 25 6. 50,18 12 1,816 0,69 30 7. 60,08 9 1,538 0,63 23
45
A.4 Membran komposit silicalite-1
Pos. [°2Th.] Tinggi [cts] FWHM [°2Th.] d [Å] Int. Rel [%] Lebar tip [°2Th.]20,8077 322,51 0,4896 4,26558 22,46 0,5875 26,6280 1436,04 0,3264 3,34494 100,00 0,3917 33,2041 67,91 0,5712 2,69597 4,73 0,6854 35,6467 82,04 0,4896 2,51663 5,71 0,5875 36,5051 149,97 0,3264 2,45940 10,44 0,3917 39,4328 73,09 0,3264 2,28328 5,09 0,3917 42,4485 92,40 0,3264 2,12778 6,43 0,3917 44,5835 191,96 0,3264 2,03072 13,37 0,3917 45,8178 91,98 0,3264 1,97884 6,41 0,3917 50,1133 241,87 0,3264 1,81883 16,84 0,3917 54,8376 66,40 0,8160 1,67278 4,62 0,9792 59,9416 134,72 0,3264 1,54196 9,38 0,3917 67,9964 98,61 0,9792 1,37758 6,87 1,1750 75,6417 83,85 0,4896 1,25621 5,84 0,5875 79,9231 73,90 0,3264 1,19933 5,15 0,3917 81,3047 40,93 0,4896 1,18241 2,85 0,5875 90,6071 26,37 0,6528 1,08364 1,84 0,7834 96,1179 39,32 0,4896 1,03558 2,74 0,5875
B.1 Inte
B.2 Inte
La
erpretasi di
erpretasi di
ampiran B
ifraktogram
M
ifraktogram
B Interpr
m serbuk b
Nama FasaMontmorilloni
Bentonit Kuarsa
MuscoviteBeidellite
Illite
m silicalite-
Nama FasaSilicalite-1
Kuarsa
etasi Difr
bentonit
% beratite 14,7
14,7 7,6
31,5 14,7 16,8
-1
% berat78,0 22,0
raktogram
t
m
47
B.3 Interpretasi membran komposit silicalite-1
Nama Fasa % beratKuarsa 62,8
Cu5(OH)2(SiO3)4 37,2
Lampiran C Foto-foto
C.1 Material pendukung membran bentonit
C.2 Membran komposit silicalite-1
2,50 cm
2,50 cm
Lampiran D Contoh Perhitungan
D.1 Contoh perhitungan fluks
Fluks = VA
Contoh perhitungan fluks air menggunakan material pendukung membran bentonit dengan
laju alir 157,6 L/jam pada waktu 5 menit, yaitu:
Fluks = VA
, L , LL
, ,37,9 L/m jam
Dengan menggunakan cara perhitungan yang sama, dapat dihitung fluks untuk data-data
yang lainnya.
D.2 Contoh perhitungan konsentrasi ion Cu2+
Persamaan garis linear :
y = 0,116 x - 0,017
A = 0,116 [Cu2+] - 0,017
Contoh perhitungan konsentrasi awal ion Cu2+ dalam larutan umpan dengan filtrasi
menggunakan material pendukung membran bentonit, yaitu:
A = 0,4622
Dengan memasukkan nilai absorbansi ke dalam persamaan garis maka:
A = 0,116 [Cu2+] - 0,017
0,4622 = 0,116 [Cu2+] - 0,017
[Cu2+] = 4,13 ppm
Perhitungan konsentrasi awal ion Cu2+ :
[Cu2+] awal = 4,13 x f
= 4,13 x 20
= 82,60 ppm
Dengan menggunakan cara perhitungan yang sama maka dapat dihitung besar konsentrasi
ion Cu2+ dari nilai absorbansi untuk data-data yang lainnya.
50
D.3 Contoh perhitungan % rejeksi
f
p
f
pf
cc
1c
ccR −=
−=
Contoh perhitungan % rejeksi ion Cu2+ menggunakan material pendukung membran bentonit
pada menit ke-30, yaitu:
% R = 1-cp
cf x 100% = 1- 33,00
64,40 x 100% = 48,75%
Dengan menggunakan cara perhitungan yang sama, dapat dihitung % rejeksi untuk data-data
yang lainnya.
Lampiran E Pengukuran Fluks Air dan Fluks Garam
E.1 Pengukuran fluks air material pendukung membran bentonit
E.1.1 Pengukuran fluks air dengan kondisi laju alir 157,6 L/jam dan waktu kompaksi 45 menit
Waktu (menit)
Material pendukung membran bentonit
1 2 3 Volume
(mL) Fluks air
(L/m2 jam) Volume
(mL) Fluks air
(L/m2 jam) Volume
(mL) Fluks air
(L/m2 jam) 5 1,20 37,9 1,20 37,9 1,20 37,9 10 1,20 37,9 1,10 34,7 1,20 37,9 15 1,20 37,9 1,10 34,7 1,20 37,9 20 1,20 37,9 1,10 34,7 1,20 37,9 25 1,10 34,7 1,10 34,7 1,20 37,9 30 1,20 37,9 1,10 34,7 1,20 37,9
Fluks rata-rata (L/m2 jam) - 37,4 - 35,3 - 37,9
E.1.2 Pengukuran fluks air dengan kondisi laju alir 218,4 L/jam dan waktu kompaksi 30 menit
Waktu (menit)
Material pendukung membran bentonit 1 2 3
Volume (mL)
Fluks air (L/m2 jam)
Volume (mL)
Fluks air (L/m2 jam)
Volume (mL)
Fluks air (L/m2 jam)
5 1,80 56,9 1,80 56,9 1,80 56,9 10 1,80 56,9 1,80 56,9 1,80 56,9 15 1,80 56,9 1,80 56,9 1,80 56,9 20 1,80 56,9 1,80 56,9 1,80 56,9 25 1,80 56,9 1,80 56,9 1,80 56,9 30 1,80 56,9 1,80 56,9 1,80 56,9
Fluks rata-rata (L/m2 jam) - 56,9 - 56,9 - 56,9
52
E.1.3 Pengukuran fluks air dengan kondisi laju alir 283,4 L/jam dan waktu kompaksi 10 menit
Waktu (menit)
Material pendukung membran bentonit 1 2 3
Volume (mL)
Fluks air (L/m2 jam)
Volume (mL)
Fluks air (L/m2 jam)
Volume (mL)
Fluks air (L/m2 jam)
5 2,20 69,5 2,10 66,3 2,20 69,5 10 2,20 69,5 2,10 66,3 2,20 69,5 15 2,20 69,5 2,10 66,3 2,20 69,5 20 2,20 69,5 2,10 66,3 2,20 69,5 25 2,20 69,5 2,10 66,3 2,20 69,5
Fluks rata-rata (L/m2 jam) - 69,5 - 66,3 - 69,5
53
E.2 Pengukuran fluks air membran komposit silicalite-1
E.2.1 Pengukuran fluks air dengan kondisi laju alir 157,6 L/jam dan waktu kompaksi 2,5 jam
Waktu (menit) Membran Silicalite-1 1 Membran Silicalite-1 2
Volume (mL) Fluks air (L/m2 jam) Volume (mL) Fluks air
(L/m2 jam)30 1,60 8,4 1,60 8,4 60 1,60 8,4 1,60 8,4 90 1,60 8,4 1,60 8,4
120 1,60 8,4 1,60 8,4 150 1,60 8,4 1,60 8,4 180 1,60 8,4 1,60 8,4
Fluks air rata-rata (L/m2 jam) - 8,4 - 8,4
E.2.2 Pengukuran fluks air dengan kondisi laju alir 218,4 L/jam dan waktu kompaksi 2,5 jam
Waktu (menit) Membran Silicalite-1 1 Membran Silicalite-1 2
Volume (mL) Fluks air (L/m2 jam) Volume (mL) Fluks air
(L/m2 jam)30 1,70 8,9 1,70 8,9 60 1,70 8,9 1,60 8,4 90 1,60 8,4 1,60 8,4
120 1,70 8,9 1,70 8,9 150 1,70 8,9 1,60 8,4 180 1,70 8,9 1,70 8,9
Fluks air rata-rata (L/m2 jam) - 8,9 - 8,7
54
E.2.3 Pengukuran fluks air dengan kondisi laju alir 283,4 L/jam dan waktu kompaksi 2,5 jam
Waktu (menit) Membran Silicalite-1 1 Membran Silicalite-1 2
Volume (mL) Fluks air (L/m2 jam) Volume (mL) Fluks air
(L/m2 jam)30 1,80 9,5 1,80 9,5 60 1,80 9,5 1,60 8,4 90 1,60 8,4 1,80 9,5
120 1,80 9,5 1,80 9,5 150 1,80 9,5 1,80 9,5 180 1,80 9,5 1,80 9,5
Fluks air rata-rata (L/m2 jam) - 9,3 - 9,3
55
E.3 Pengukuran fluks garam menggunakan material pendukung membran bentonit
Waktu (menit) Volume (mL) Fluks garam (L/m2 jam)
30 3,00 15,8 60 3,00 15,8 90 3,00 15,8
120 3,00 15,8 150 3,00 15,8 180 3,00 15,8
Fluks air rata-rata(L/m2 jam) - 15,8
E.4 Pengukuran fluks garam menggunakan membran komposit silicalite-1
Waktu (menit) Volume (mL) Fluks garam (L/m2 jam)
30 1,10 5,8 60 1,10 5,8 90 1,10 5,8
120 1,10 5,8 150 1,10 5,8 180 1,10 5,8
Fluks air rata-rata(L/m2 jam) - 5,8
Lampiran F Kurva Kalibrasi
F.1 Data pengamatan
[Cu2+] (ppm) A 0,10 0,00610,50 0,03931,00 0,08623,00 0,33515,00 0,55888,00 0,9190
F.2 Kurva kalibrasi ion Cu2+
y = 0,116x ‐ 0,017R² = 0,999
‐0,2
0
0,2
0,4
0,6
0,8
1
0 2 4 6 8 10
A
[Cu2+ ] (ppm)
Lampiran G Pengukuran % Rejeksi Ion Cu2+
G.1 Pengukuran % rejeksi terhadap ion Cu2+ menggunakan material pendukung membran bentonit dengan fluks garam 15,8 L/m2 jam
Waktu (menit)
Umpan Permeat
A [Cu2+] (ppm) f [Cu2+] awal (ppm) A [Cu2+] (ppm) f [Cu2+] awal
(ppm)
0 0,4622 4,13 20 82,60 0 0 - 0
30 0,3561 3,22 20 64,40 0,0599 0,66 50 33,00
60 0,3009 2,74 20 54,80 0,0535 0,61 50 30,50
90 0,249 2,29 20 45,80 0,0488 0,57 50 28,50
120 0,2117 1,97 20 39,40 0,0376 0,47 50 23,50
150 0,1639 1,56 20 31,20 0,0280 0,39 50 19,50
Waktu (menit)[Cu2+] (ppm)
% rejeksi
Umpan Permeat
30 64,40 33,00 48,75
60 54,80 30,50 44,34
90 45,80 28,50 37,77
120 39,40 23,50 40,35
150 31,20 19,50 37,50
58
G.2 Pengukuran % rejeksi terhadap ion Cu2+ menggunakan membran komposit silicalite-1 dengan fluks garam 5,8 L/m2 jam
Waktu (menit)
Umpan Permeat
A [Cu2+] (ppm) f [Cu2+] awal (ppm) A [Cu2+] (ppm) f [Cu2+] awal
(ppm)
0 0,4740 4,23 20 84,70 0 0 - 0
30 0,0298 0,40 100 40,34 0,1205 1,19 20 23,80
60 0,0118 0,25 100 24,83 0,0582 0,65 20 13,00
90 0,0115 0,25 100 24,57 0,0557 0,63 20 12,60
120 0,0111 0,24 100 24,22 0,0076 0,21 50 10,50
150 0,0075 0,21 100 21,12 0,0258 0,37 20 7,40
Waktu (menit)Konsentrasi larutan (ppm)
% rejeksi
Umpan Permeat
30 40,34 23,80 41,00
60 24,83 13,00 47,64
90 24,57 12,60 48,72
120 24,22 10,50 56,65
150 21,12 7,40 64,96
Lampiran H Foto SEM dan EDX
H.1 Penampang muka silicalite-1
Unsur (keV) % berat % kesalahan % At Senyawa % berat Kation
O - 52,80 - - - - - -
Al K 1,486 1,48 1,34 1,67 Al2O3 2,79 0,40 2,7355
Si K 1,739 45,02 1,29 97,60 SiO2 96,32 11,66 95,7406
Fe K 6,398 0,46 3,49 0,50 FeO 0,60 0,06 1,0171
Cu K 8,040 0,24 6,69 0,23 CuO 0,30 0,03 0,5068
Total - 100,00 - 100,00 - 100,00 12,14 -
60
H.2 Penampang muka bentonit
Unsur (keV) % berat % kesalahan % At Senyawa % berat Kation
O - 47,50 - - - - - -
Mg K 1,253 1,56 0,79 4,39 MgO 2,58 0,52 2,3955
Al K 1,486 15,49 0,87 19,67 Al2O3 29,27 4,64 28,1844
Si K 1,739 26,28 0,97 64,11 SiO2 56,22 7,56 47,2222
Ca K 3,690 1,26 1,05 2,15 CaO 1,76 0,25 3,4125
Fe K 6,398 7,72 2,05 9,47 FeO 9,93 1,12 18,3519
Cu K 8,040 0,19 4,09 0,21 CuO 0,24 0,02 0,4335
Total - 100,00 - 100,00 - 100,00 14,12 -