Accessories

Preparation1 2

Spacers (2.3 mm) x 4 Adhesive Tape x 1Washers x 4Screws x 4 (M2)

Heatsinks

A x 11 B x 2 C x 4 D x 4 E x 5

Accelero TWIN TURBO IIInstallation Manual

Ensure there is no physical interference between the heatsinks and the circuit components as it may cause short circuit. Use tape to cover the circuit components when necessary.

Ensure there is no physical interference between the heatsinks and the circuit components as it may cause short circuit. Use tape to cover the circuit components when necessary.

Spacers (4 mm) x 4

Spacer

AdhesiveTape

Spacer

AdhesiveTape

X 4

Protective Film5

4 Choose the right mounting hole and spacers:

6

Instalační příručka: www.arctic.ac/fileadmin/att2/manual_cz.pdfTelepítési kézikönyv: www.arctic.ac/fileadmin/att2/manual_hu.pdfInstrukcja montażu: www.arctic.ac/fileadmin/att2/manual_pl.pdfInstallatiehandleiding: www.arctic.ac/fileadmin/att2/manual_nl.pdf

Montageanleitung: www.arctic.ac/fileadmin/att2/manual_de.pdfGuide d’installation: www.arctic.ac/fileadmin/att2/manual_fr.pdfManual de instalación: www.arctic.ac/fileadmin/att2/manual_es.pdfManual de Instalação: www.arctic.ac/fileadmin/att2/manual_pt.pdfInstallationsmanual: www.arctic.ac/fileadmin/att2/manual_se.pdf

Remove the mounting plate from the cooler and fix it on top of your VGA card to the position of the mounting holes. Now you should be able to see the exact position of the mounting plate occupied area to avoid the interference of the RAM heatsinks and mounting plate.

7

3

Please note this table is for reference only. Refer to your own VGA card holes position during installation.The updated information is available at att2.arctic.ac.

??43.2 mm - use43.2 mm - use53.2 mm - use53.2 mm - use51.0 mm - use51.0 mm - use58.4 mm - use58.4 mm - use

Not cleaning circuit components thoroughlywith an eraser leads to no adhesivenessof the G-1.

8

Must thoroughly mix the entire amount of compound of both bags for 5 minutes.Not mixing for 5 minutes will lead to no adhesiveness of the glue. Application has to be done within 15 minutes thereafter.

+

5 mins

4-pin FanPower Adapterx 1

VGA Bracketx 1

Mixing Wandx 1

G-1 (White Compound 2 g)G-1 (Grey Compound 2 g)

EN

Mounting Hole Compatible Models①① 43.2 mm x 43.2 mm NVIDIA GeForce:

6600 GT AGP, 6600 GT, 6600 LE, 6600 DDR2, 6600AMD Radeon:HD 6770, 4770, 2600 XT, X1650 XT, X1650 Pro, X1600 XT, X1600 Pro,X1550, X1300 XT, X1300 Pro, X1300

②② 53.2 mm x 53.2 mm

③③ 51.0 mm x 61.0 mm NVIDIA GeForce:GTX 560Ti, GTX 560, GTX 550 Ti, GTX 460 SE, GTX 460

Use Spacers2.3 mm

2.3 mm

4.0 mm

NVIDIA GeForce: 8800 GTX (G80), 8800 GTS (G80)

4.0 mm

NVIDIA GeForce:GTS 550, GTS 450, GT 340, GT 330, GT 320, GTS 250,GTS 240 (OEM), GT 130 (OEM), 9800 GTX+, 9800 GTX, 9800 GT, 9600 GT, 9600 GSO 512, 9600 GSO, 8800 GTS 512 (G92), 8800 GTS (G92), 8800 GT, 8800 GS (9600GSO), 7950 GT,7900 GTX, 7900 GT, 7900 GS, 7800 GTX 512, 7800 GTX,7800 GT, 6800 Ultra Extreme, 6800 Ultra, 6800 GT, 6800 GS AGP, 6800 GS, 6800 AGP, 6800, 6800 XT AGP, 6800 XT, 6800 LEAMD Radeon:HD 6950, 6870, 6850, 6790, 5870, 5850, 5830, 4890, 4870, 4850, 4830, 3870, 3850, X1950 XTX, X1950 XT, X1950 Pro, X1950 GT, X1900 XTX, X1900 XT, X1900 GT, X1800 XT, X1800 XL, X1800 GTO

58.4 mm x 58.4 mm

Installation example on GTX 560 Ti1 2

3

1

Apply thermal glue on all circuit components.

Tips for applying G-1RAM Cure time

5 hours

1 2 4

Install the heatsinks without touching the mounting plate.

4

Installation of Accelero TWIN TURBO IIThe flexible mounting plate of Accelero TWIN TURBO II is designed for fitting different GPU locations. Measure the distance between the center of the GPU and the edge of the card.The default mounting position (B) is for distance between 55 mm to 65 mm.

A x 8

Heatsinks

B x 1

Heatsinks

E x 1

Heatsinks

Apply pressure(10 sec)

3

WarrantyThis ARCTIC Product includes a 6-year limited warranty. Please visit warranty.arctic.ac for further details.

The thermal compound is already pre-applied to the heatsink. If the cooler has to be installed a second time, we highly recommend using the MX-4 from ARCTIC. Only this compound guarantees optimal performance in combination with the surface of our heatsinks.

Thermal Compound

Remove the mounting plate from the VGA card and screw it back to the cooler.2

3

Install the main cooler to the VGA card by fastening each screw alternately (screw A->D->B->C) with 2 to 3 clockwise rotations. Repeat until all 4 screws are tightened. Do not fasten the screws completely in one step.

E x 2

Heatsinks

? mm? mm

A: < 55 mmB: 55 mm - 65 mmC: > 65 mm

BBAA

CC

ARCTIC SwitzerlandHuobstrasse 48808, Pfäffikon, Switzerlandwww.arctic.ac

Copyright2011 ARCTIC (HK) Ltd. All Rights ReservedNo part of this manual including the products described in it, may be reproduced, transmitted, stored in a retrieval system, or translated into any language in any form or by any means, except documentation kept by the purchaser for backup purpose, without the express written permission of ARCTIC (HK) Ltd. In no event shall ARCTIC its directors or employees be liable for any indirect damages, incidental or consequential damages arising from any defect or error in this manual or product.

Voltage regulator(apply glue generously)Voltage regulator(apply glue generously)