+ All Categories

Home > Documents > ACCEPTANCE CRITERIA FOR MECHANICAL CONNECTOR SYSTEMS FOR STEEL REINFORCING BARS (AC133) and...

ACCEPTANCE CRITERIA FOR MECHANICAL CONNECTOR SYSTEMS FOR STEEL REINFORCING BARS (AC133) and...

Date post:	13-Apr-2020
Category:	Documents
Upload:	others
View:	45 times
Download:	3 times

Download Report this document

Share this document with a friend

Embed Size (px):

7

Transcript

Page 1: ACCEPTANCE CRITERIA FOR MECHANICAL CONNECTOR SYSTEMS FOR STEEL REINFORCING BARS (AC133) and 21.11.7.4 of ACI 318 describes permitted uses for each type of splice under the IBC and

Page 2: ACCEPTANCE CRITERIA FOR MECHANICAL CONNECTOR SYSTEMS FOR STEEL REINFORCING BARS (AC133) and 21.11.7.4 of ACI 318 describes permitted uses for each type of splice under the IBC and

Page 3: ACCEPTANCE CRITERIA FOR MECHANICAL CONNECTOR SYSTEMS FOR STEEL REINFORCING BARS (AC133) and 21.11.7.4 of ACI 318 describes permitted uses for each type of splice under the IBC and

Page 4: ACCEPTANCE CRITERIA FOR MECHANICAL CONNECTOR SYSTEMS FOR STEEL REINFORCING BARS (AC133) and 21.11.7.4 of ACI 318 describes permitted uses for each type of splice under the IBC and

Page 5: ACCEPTANCE CRITERIA FOR MECHANICAL CONNECTOR SYSTEMS FOR STEEL REINFORCING BARS (AC133) and 21.11.7.4 of ACI 318 describes permitted uses for each type of splice under the IBC and

Page 6: ACCEPTANCE CRITERIA FOR MECHANICAL CONNECTOR SYSTEMS FOR STEEL REINFORCING BARS (AC133) and 21.11.7.4 of ACI 318 describes permitted uses for each type of splice under the IBC and

Page 7: ACCEPTANCE CRITERIA FOR MECHANICAL CONNECTOR SYSTEMS FOR STEEL REINFORCING BARS (AC133) and 21.11.7.4 of ACI 318 describes permitted uses for each type of splice under the IBC and

Recommended

TVC - COYOTE MPC · 2009-02-17 · Low Profile Tray (12 splice count) Cat. #80807701 (w/splice blocks) or #8001130 (blank) Ribbon Tray (72 splice count) Cat. # 80807114 (w/splice

Splice-on Connector - greenlee-cdn. · PDF filetension test (proof) be disabled for the splice-on connectors. 6. Splice Loss Estimation: The splicer will estimate the splice loss based

Mechanical Splice Report - Pennsylvania Department of ... · evaluation of offset reinforcing bar splice systems. This protocol/test is intended to ensure the conformance of such

BOND BEHAVIOR OF GRADE 100 ASTM A 1035 REINFORCING STEEL ...iri/publications/SLR07_1.pdf · BOND BEHAVIOR OF GRADE 100 ASTM A 1035 REINFORCING STEEL IN BEAM-SPLICE SPECIMENS By Michael

INSTRUCTION MANUAL- PLANT OPERATIONS - NMB Splice … Plant Operations 2014.pdf · instruction manual- plant operations nmb splice sleeve system- reinforcing bar connector revised

Example Column Splice - Non-bearing Splice

LAP SPLICE PERFORMANCE OF REINFORCING BAR IN HIGH ...

Column Splice Final

Author's personal copy - Nc State University · current ACI 318-08 [11] provisions for development and splice ... to use lap splices for reinforcing bars larger than No. 11 ... Author's

GRABB-IT Cable Splice Installation Instructions · GRABB-IT Cable Splice Installation Instructions Required Equipment: 1) GRABB-IT Cable Splice assembly and Chuck Splice (if required).

Noninvasive positron emission tomography and fluorescence … · chelator NOTA, we radiolabeled the AC133 mAb, which rec-ognizes the AC133 epitope on CD133-overexpressing cells and

16 · PDF fileall reinforcing steel shall be of ... for closely spaced bars lapping may be ... specified length of the lap splice shall be 4. clear concrete cover to

FIS Splice-On Connector Reference Guide7. Splice Sleeves: Heat shrink sleeves installed prior to splice now are moved into position centered over splice area and placed in oven. 8.

Bad splice detection