1 Appearance The silkscreen LSR1WCM2A1 is printed at the upper right corner of the front panel, which is used to identify the module. The following figure depicts the appearance of the module.
Figure 1 Appearance of the LSRM1WCM2A1
2 Specifications The LSRM1WCM2A1 can provide wireless services to S9500E series switches. The following figure depicts the front panel of the LSRM1WCM2A1.
Figure 2 Front panel of the LSRM1WCM2A1
(1) Captive screw (2) Ejector lever (3) USB interface 1 (4) USB interface 2 (5) 10/100/1000Base-T out-of-band management Ethernet port (MGMNT) (6) 10/100/1000Base-T out-of-band management Ethernet port status LED (LINK) (7) 10/100/1000Base-T out-of-band management Ethernet port status LED (ACT) (8) Console port (CONSOLE)
Table1 LSRM1WCM2A1 specifications
Item Specification
CPU frequency 600 MHz
Manual Version: APW100-20090227 BOM: 3123A0A1
ii
Item Specification
CF card 256 MB
Capacity 1 GB DDRII
Dimensions (H × W × D) 40.6 × 366.7 × 340 mm (1.60 × 14.44 × 13.39 in.)
Power consumption 80 W to 105 W
Weight 3.58 kg (7.89 lb)
Interface Two USB interfaces (USB 1.1-compliant) One 10/100/1000Base-T management Ethernet port One console port
Operating temperature 0°C to 45°C (32°F to 113°F)
Operating humidity (noncondensing) 10% to 95%
Applicable device model S9505E/S9508E-V/S9512E
Applicable host software version S9500E-CMW520-A1132 or later versions
3 Installing and Removing the LSRM1WCM2A1
Avoid touching any components on the module during the installation or removal process. It is recommended to wear an ESD-preventive wrist strap and ESD-preventive gloves before installation.
The LSRM1WCM2A1 is hot swappable.
Installing the LSRM1WCM2A1
(1) Face the front panel of the switch.
(2) Choose an empty slot and remove the filler panel.
(3) Push the access controller module into the slot along the guide rails until the positioning hole of
the module is seated onto the positioning pin on the backplane.
(4) Push the ejector levers inward to lock the access controller module in place.
(5) Fasten the captive screws on the access controller module with a Philips screwdriver.
Figure 3 Installing the LSRM1WCM2A1
Manual Version: APW100-20090227 BOM: 3123A0A1
iii
(1) Push the access controller module into the slot along the guide rails until the positioning hole of the module is seated onto the positioning pin on the backplane. (2) Push the ejector levers inward to lock the access controller module in place.
Removing the LSRM1WCM2A1
(1) Face the front panel of the switch.
(2) Loosen the captive screws on the access controller module with a Philips screwdriver until all
spring pressure is released.
(3) Hold the ejector levers of the access controller module and push them outward.
(4) Gently pull the access controller module out of the slot along the guide rails.
4 Upgrading the LSRM1WCM2A1 The LSRM1WCM2A1 has its own Boot ROM program and application program with a Boot ROM menu different from that of the S9500E series switches. To update the application program of the LSRM1WCM2A1, use one of the following ways:
(1) Local update through the Boot ROM menu
Use the XMODEM protocol through the console port of the LSRM1WCM2A1
Use the TFTP protocol through the 10/100/1000Base-T Ethernet port of the LSRM1WCM2A1
(2) Remote update through CLI
Use the FTP protocol through the 10/100/1000Base-T Ethernet port of the LSRM1WCM2A1
Use the TFTP protocol through the 10/100/1000Base-T Ethernet port of the LSRM1WCM2A1
Manual Version: APW100-20090227 BOM: 3123A0A1
iv
You can upgrade the LSRM1WCM2A1 through its console port or Ethernet port. For details, refer to H3C Access Controller Module Software Maintenance Manual.
5 Guidelines
If the host software version does not match the access controller module, contact the sales
agent or the integrator for the right version.
For how to upgrade the host software version, refer to the related part in H3C S9500E Series
Routing Switches Installation Manual.
The types and specifications of the access controller modules may vary with product versions.
For the latest documentation, go to Technical Support & Document > Technical Documents
