AccuPyc Bibliography of Peer-Reviewed Papers · PDF fileAccuPyc Bibliography of Peer-Reviewed...

AccuPyc Bibliography of Peer-Reviewed Papers

2013

TITLE AUTHORS & PUBLICATION CITATION

A methodological approach for determining

the effect of moisture content on the

compaction properties of powders: Granular

hydroxyapatite

Wade, J.B. / Martin, G.P. / Long, D.F., Powder

Technology, 246, p.511-519, Sep 2013

..was determined using helium pycnometry (Helium AccuPyc 1330, Micromeritics,

Norcross, Georgia, USA). The instrument was...a nitrogen adsorption method

(TriStar 3000, Micromeritics, Norcross, Georgia, USA). Samples were outgassed...

A methodological approach for determining

the effect of moisture content on the

compaction properties of powders: Granular

hydroxyapatite

Wade, J.B. / Martin, G.P. / Long, D.F., Powder

Technology, 246, p.511-519, Sep 2013

..using helium pycnometry (Helium AccuPyc 1330, Micromeritics, Norcross, Georgia,

USA). The instrument was...measured using a nitrogen adsorption method (TriStar

3000, Micromeritics, Norcross, Georgia, USA). Samples were outgassed...

A simple route for organic covalent grafting

onto zirconium carbide particles

Lucas, Romain / Pizon, David / Laborde, Etienne /

Trolliard, Gilles / Foucaud, Sylvie / Maître,

Alexandre, Applied Surface Science, In Press,

Corrected Proof,Oct 2013

..carbide powder, laser granulometry analyses were performed (AccuPyc II 1340,

Micrometrics France S.A. Verneuil Halatte...measured thanks to the gas adsorption

method (ASAP 2010, Micromeritics France S.A., Verneuil Halatte, France). Samples

(450...

Adsorbent density impact on gas storage

capacities

Kunowsky, Mirko / Suárez-García, Fabián /

Linares-Solano, Ángel, Microporous and

Mesoporous Materials, 173, p.47-52, Jun 2013

..was evaluated, taking into account a reference measurement without sample.

True densities were measured in a Micromeritics Accupyc 1330 pycnometer. Before

every measurement the samples were degassed at 393 K into vacuum for at least 4

h, and...

Adsorption kinetics of herbicide paraquat in

aqueous solution onto a low-cost adsorbent,

swine-manure-derived biochar

WT Tsai, HR Chen - International Journal of

Environmental Science and … - Springer

... of total pore volume and true density. g Measured by the helium-displacement

method using an AccuPyc 1340 pycnometer (Micromeritics Co., USA ... purity of

minimum 87.0 %) were immediately made with a 1.0 cm light path quartz cell in a

spectrophotometer (Hitachi U-2900) at λ

An experimental and numerical study of

packing, compression, and caking behaviour

of detergent powders

Thakur, Subhash C. / Ahmadian, Hossein / Sun,

Jin / Ooi, Jin Y., Particuology, In Press, Corrected

Proof,Sep 2013

..and mercury porosimetry. A gas pycnometer, Accupyc II 1340 (Micromeritics,

USA), was used to measure skeletal density...conducted using mercury porosimetry

(AutoPore IV, Micromeritics, USA). The instrument provides a wide range...

An experimental and numerical study of

packing, compression, and caking behaviour

of detergent powders

Thakur, Subhash C. / Ahmadian, Hossein / Sun,

Jin / Ooi, Jin Y., Particuology, In Press, Corrected

Proof,Sep 2013

..porosimetry. A gas pycnometer, Accupyc II 1340 (Micromeritics, USA), was used to

measure skeletal density...samples was conducted using mercury porosimetry

(AutoPore IV, Micromeritics, USA). The instrument provides a wide range...

Anacardium occidentale L. leaves extraction

via SFE: Global yields, extraction kinetics,

mathematical modeling and economic

evaluation

Leitão, N.C.M.C.S. / Prado, G.H.C. / Veggi, P.C. /

Meireles, M.A.A. / Pereira, C.G., The Journal of

Supercritical Fluids, 78, p.114-123, Jun 2013

..32 (4.1%), and 48 (27%). The real density of the particles was measured using

helium picnometry (Micromeritics, AccuPyc II 1340, Norcross, USA) by Analytical

Facilities of the Institute of Chemistry (IQ/Unicamp). The apparent...

Anisotropy of green stoneware evaluated by

ultrasound measurements in combination

with texture analyses

Romagnoli, Marcello / Lassinantti Gualtieri,

Magdalena / Gualtieri, Alessandro F. / Šliteris,

Reimondas / Kažys, Rymantas / Tari, Giuliano,

Journal of the European Ceramic Society, 33 (13-

14), p.2785-2792, Nov 2013

..density ( ρ t ) of the dried starting powder was determined using a gas

displacement pycnometer instrument (AccuPyc 1330, Micromeritics Inc., USA).

Total porosity ( TP ) was calculated according to 23 : (1) T P = 1 − ρ ρ t × 100

Porosimetry...

http://www.sciencedirect.com/science/article/pii/S0032591013004257












http://link.springer.com/article/10.1007%2Fs13762-012-0174-z



http://www.sciencedirect.com/science/article/pii/S167420011300179X














Anisotropy of green stoneware evaluated by

ultrasound measurements in combination

with texture analyses

Romagnoli, Marcello / Lassinantti Gualtieri,

Magdalena / Gualtieri, Alessandro F. / Šliteris,

Reimondas / Kažys, Rymantas / Tari, Giuliano,


14), p.2785-2792, Nov 2013

..a gas displacement pycnometer instrument (AccuPyc 1330, Micromeritics Inc.,

USA). Total porosity ( TP ) was calculated according...ρ ρ t × 100 Porosimetry data

were collected using an Autopore IV 9500 scanning mercury porosimeter. The

contact angle...

Ba 0.5 Sr 0.5 Co 0.8 Fe 0.2 O 3− δ (BSCF)

feedstock development and optimization for

thermoplastic forming of thin planar and

tubular oxygen separation membranes

Salehi, Mehdi / Pfaff, Ewald M. / Junior, Roberto

Morkis / Bergmann, Carlos P. / Diethelm, Stefan /

Neururer, Christoph / Graule, Thomas / (...) / Jörg

Clemens, Frank, Journal of Membrane Science,

443, p.237-245, Sep 2013

..the powders were measured by He-pycnometer (Micromeritics, AccuPyc 1330,

USA). 2.2 Feedstock preparation...of the same feedstock using He-pycnometer

(Micromeritics, AccuPyc 1330, USA). The rheology of the feedstocks...

Behaviour of a bauxite waste material as

oxygen carrier in a 500 W th CLC unit with

coal

Mendiara, T. / de Diego, L.F. / García-Labiano, F. /

Gayán, P. / Abad, A. / Adánez, J., International

Journal of Greenhouse Gas Control, 17, p.170-

182, Sep 2013

..measured by Hg intrusion in a Quantachrome PoreMaster 33. The skeletal density

of the particles was measured with a Micromeritics AccuPyc II 1340 helium

picnometer. Brunauer–Emmett–Teller (BET) surface area value was measured and a

low value...

Bimodal distribution of filler on viscosity and

thermal expansion of glass composites

Samal, Sneha / Cho, Sunghwan / Kim, Hyungsun,

Ceramics International, 39 (2), p.1659-1666, Mar

2013

..microscope (SEM; Hitachi S-4300). The densities of the green composites were

calculated by using a pycnometer (Micromeritics, Accupyc II 1340). The

crystallization phases of the green and fired composites were analyzed using XRD

techniques...

Bone marrow absorption and retention

properties of engineered scaffolds with

micro-channels and nano-pores for tissue

engineering: A proof of concept

Oh, Daniel S. / Hyuk Kim, Yoon / Ganbat, Danaa /

Han, Myung-Ho / Lim, Phillip / Back, Jung-Ho /

Lee, Francis Y. / Tawfeek, Hesham, Ceramics

International, 39 (7), p.8401-8410, Sep 2013

..micro-CT (SkyScan 1172), mechanical testing (5848 Instron MicroTester), and

helium pycnometry (porosity: AccuPyc II 1340 micromeritics). We had three scaffold

groups based on their average macro-pore sizes (450 um, 320 um, and 200 um...

Boron nitride nanotubes reinforced

aluminum composites prepared by spark

plasma sintering: Microstructure, mechanical

properties and deformation behavior

Lahiri, Debrupa / Hadjikhani, Ali / Zhang, Cheng /

Xing, Tan / Li, Lu Hua / Chen, Ying / Agarwal,

Arvind, Materials Science and Engineering: A,

574, p.149-156, Jul 2013

..reactivity of Al with BNNT. The density of the sintered pellets was measured using

helium gas pycnometry (Accupyc 1340, Micromeretics Instrument Corporation,

Norcross, GA, USA) and expressed in terms of relative density, while calculating the

true density...

Bubbling fluidization of biomass and sand

binary mixtures: Minimum fluidization

velocity and particle segregation

Oliveira, T.J.P. / Cardoso, C.R. / Ataíde, C.H.,

Chemical Engineering and Processing: Process

Intensification, 72, p.113-121, Oct 2013

..true density [14] . Therefore, the materials were oven-dried at 105 °C for 24 h

before the analyses. A Micromeritics AccuPyc 1331 gas pycnometer with a

measuring sensitivity of 10 −4 g/cm 3 was used to infer the true density of the...

Bulk, surface properties and water uptake

mechanisms of salt/acid amorphous

composite systems

Bianco, Stefano / Tewes, Frederic / Tajber, Lidia /

Caron, Vincent / Corrigan, Owen I. / Healy, Anne

Marie, International Journal of Pharmaceutics,

456 (1), p.143-152, Nov 2013

..Jaoczuk, 2010 ). 2.9 Density measurements The density of spray dried ST and STNa

was measured by an Accupyc 1330 Pycnometer (Micromeritics ® ) using helium

(99.995% purity) to determine the volume of the sample. Samples were dried prior...

Carbon meringues derived from flavonoid

tannins Szczurek, A. / Fierro, V. / Pizzi, A. / Stauber, M. /

Celzard, A., Carbon, 65, p.214-227, Dec 2013

..pycnometry using an Accupyc II 1340 (Micromeritics) automatic apparatus. For

that purpose...at −196 °C using an ASAP 2020 (Micromeritics) automatic apparatus.

All the samples...determined by mercury intrusion, using an AutoPore IV 9500

(Micrometrics) porosimeter...




http://doc.rero.ch/record/32047




http://digital.csic.es/bitstream/10261/84940/1/Behviour_of_a_bauxite_waste.pdf
















http://www.ncbi.nlm.nih.gov/pubmed/23948137






Carbon meringues derived from flavonoid

tannins Szczurek, A. / Fierro, V. / Pizzi, A. / Stauber, M. /

Celzard, A., Carbon, 65, p.214-227, Dec 2013

..was estimated by helium pycnometry using an Accupyc II 1340 (Micromeritics)

automatic apparatus. For that purpose, all samples...adsorption at −196 °C using an

ASAP 2020 (Micromeritics) automatic apparatus. All the samples were...

Carbonate-containing apatite (CAP) synthesis

under moderate conditions starting from

calcium carbonate and orthophosphoric acid

Pham Minh, Doan / Tran, Ngoc Dung / Nzihou,

Ange / Sharrock, Patrick, Materials Science and

Engineering: C, 33 (5), p.2971-2980, Jul 2013

..P°) of 0.03 to 0.99. True density of the solid powders was measured by helium

pycnometry using an Accupyc 1330 (Micromeritics). Scanning electron microscopy

(SEM) was measured on a Philips XL30 ESEM apparatus (FEI Company). Particle...

Carbonisation of resorcinol–formaldehyde

organic xerogels: Effect of temperature,

particle size and heating rate on the porosity

of carbon xerogels

Moreno, A.H. / Arenillas, A. / Calvo, E.G. /

Bermúdez, J.M. / Menéndez, J.A., Journal of

Analytical and Applied Pyrolysis, 100, p.111-116,

Mar 2013

..The adsorption analysis was carried out with a Micromeritics Tristar 3020, for the

study of microporosity and...densities of the RF carbon xerogels were measured in a

Micromeritics AccuPyc 1340 Pycnometer. Before measuring the helium density...

Ceramic/metal nanocomposites by

lyophilization: Spark plasma sintering and

hardness

Gutierrez-Gonzalez, C.F. / Agouram, S. /

Torrecillas, R. / Moya, J.S. / Lopez-Esteban, S.,

Ceramics International, In Press, Corrected

Proof,Sep 2013

..characterize the powders obtained. The density of the powders was determined by

using a Helium Pycnometer ( AccuPyc 1330 , Micromeritics France S.A. ). X-ray

diffraction analysis of the powders at different stages of the different processing...

Characterising highly active nuclear waste

simulants

Paul, Neepa / Biggs, Simon / Edmondson,

Michael / Hunter, Timothy N. / Hammond,

Robert B., Chemical Engineering Research and

Design, 91 (4), p.742-751, Apr 2013

..modification. 2.2 Particle characterisation Particle density was measured using the

Micrometrics AccuPyc 1330 helium pycnometer (Micromeritics Instrument

Corporation, US). The input weight of the solids were measured, the density is

determined...

Characterization and performance

assessment of solid dispersions prepared by

hot melt extrusion and spray drying process

Agrawal, Anjali M. / Dudhedia, Mayur S. / Patel,

Ashwinkumar D. / Raikes, Michelle S.,

International Journal of Pharmaceutics, 457 (1),

p.71-81, Nov 2013

..5.12 True density of dispersions The true density of milled solid dispersions

powder was determined using Micromeritics AccuPyc 1330 Gas pycnometer S/N-

4011 (Norcross, GA). Calibration was performed prior to each run. Sample was...

Characterization of a gluten reference

material: Wheat-contaminated oats

Alvarez, Pedro A. / Mongeon, Vanessa J. / Boye,

Joyce I., Journal of Cereal Science, 57 (3), p.418-

423, May 2013

..cases (data not shown). Bulk density was determined via an AccuPyc II 1340 gas

pycnometer using helium at 23 °C, 100 cm 3 sample chamber, and

∼

30 g sample

size (Micromeritics Instruments Corp., Norcross, GA). Moisture of flours was...

Characterization of carbon/carbon

composites prepared by different processing

routes including liquid pitch densification

process

Dekeyrel, Alixe / Dourges, Marie-Anne /

Weisbecker, Patrick / Pailler, René / Allemand,

Alexandre / Ténèze, Nicolas / Epherre, Jean-

François, Composites Part A: Applied Science and

Manufacturing, 49, p.81-88, Jun 2013

..determined by helium pycnometry using an AccuPyc 1340 pycnometer

manufactured by Micromeritics. Apparent densities were obtained

from...characterized by mercury intrusion porosimetry (Micromeritics Autopore IV)

for pre-densified preforms...




















http://www.sciencedirect.com/science/article/pii/S1359835X13000651





Characterization of carbon/carbon

composites prepared by different processing

routes including liquid pitch densification

process

Dekeyrel, Alixe / Dourges, Marie-Anne /

Weisbecker, Patrick / Pailler, René / Allemand,

Alexandre / Ténèze, Nicolas / Epherre, Jean-

François, Composites Part A: Applied Science and

Manufacturing, 49, p.81-88, Jun 2013

..using an AccuPyc 1340 pycnometer manufactured by Micromeritics. Apparent

densities were obtained from weight...characterized by mercury intrusion

porosimetry (Micromeritics Autopore IV) for pre-densified preforms.

Microstructures...

Characterization of dynamics in complex

lyophilized formulations: II. Analysis of

density variations in terms of glass dynamics

and comparisons with global mobility, fast

dynamics, and Positron Annihilation Lifetime

Spectroscopy (PALS)

Chieng, Norman / Cicerone, Marcus T. / Zhong,

Qin / Liu, Ming / Pikal, Michael J., European

Journal of Pharmaceutics and Biopharmaceutics,

85 (2), p.197-206, Oct 2013

..2.1 Density The densities of the freeze-dried samples were obtained using a helium

pycnometer (AccuPyc 1330 Gas Pycnometer, Micromeritics Instruments

Corporation, Norcross, USA), which was described previously [19] . In order to

prevent...

Characterization of laminar extrudates

manufactured at room temperature in the

absence of solvents for the delivery of drugs

Oliveira, G. / Wahl, M.A. / Pinto, J.F.,

International Journal of Pharmaceutics, 454 (1),

p.90-98, Sep 2013

..extrudates (at 0, 1, 2, 3, 7, 10 and 20 days after production) were determined in a

helium pycnometer (AccuPyc 1330, Micromeritics, USA) at room temperature (23

°C) ( n = 3). The expected densities of the extrudates were calculated...

Characterization of polyurethane networks

structure and properties based on rapeseed

oil derived polyol

Fridrihsone, Anda / Stirna, Uldis / Lazdiņa, Brigita

/ Misāne, Marija / Vilsone, Dzintra, European

Polymer Journal, 49 (6), p.1204-1214, Jun 2013

..min −1 . The density of PU films was determined by using gas picnometry. The gas

pycnometer Micromeritics AccuPyc II 1340 from Micromeritics was used. 2.6

Calculations of structure parameters Functionality is the second most important...

Characterization of the porosity in TRISO

coated fuel particles and its effect on the

relative thermal diffusivity

Bari, Klaudio / Osarinmwian, Charles / López-

Honorato, Eddie / Abram, Timothy J., Nuclear

Engineering and Design, 265, p.668-674, Dec

2013

..linear diffusion 4-noded DC3D4 element was employed as a mesh element type in

Abaqus. Helium gas pycnometry (Micromeritics, AccuPyc II 1340) was used to

measure the absolute density of the TRISO particles and the total pore volume of

the OPyC...

Chitosan macroporous foams obtained in

highly concentrated emulsions as templates

Miras, Jonathan / Vílchez, Susana / Solans,

Conxita / Esquena, Jordi, Journal of Colloid and

Interface Science, 410, p.33-42, Nov 2013

..kV. 2.6.2 Helium pycnometry Matrix or skeletal density of macroporous foams was

determined using a Helium Micromeritics AccuPyc 1330 pycnometer. The average

density was calculated by means of the measurement of four replicas. The total...

Chromatographic separation of wood model

constituents - Mathematical modeling and

parameter estimation

Westerberg, Niklas / Rasmuson, Anders,

Chemical Engineering Research and Design, In

Press, Accepted Manuscript,Oct 2013

..volume calculated from these experiments. In addition to these experiments the

solid density was measured using a Micromeritics Accupyc 1330 pycnometer. From

the solid density the total porosity of the column could be derived if the mass of

the...

CiteEnergetic salts based on 1-methoxy-5-

nitroiminotetrazoleYH Joo, JH Chung, SG Cho, EM Goh - New Journal

of Chemistry, 2013 - pubs.rsc.org

... Densities of the 1-methoxy-5-nitroiminotetrazole salts were determined at 25 °C

by employing a Micromeritics AccuPyc 1340 gas pycnometer. ... Raman (532 nm, 50

mW) ν/cm −1 3319, 3248, 3017, 2950, 1509, 1309, 1292, 1092, 1025, 967.

Comparative study of the nano-composite

electrolytes based on samaria-doped ceria

for low temperature solid oxide fuel cells (LT-

SOFCs)

Khan, M. Ajmal / Raza, Rizwan / Lima, Raquel. B.

/ Chaudhry, M. Asharf / Ahmed, E. / Abbas,

Ghazanfar, International Journal of Hydrogen

Energy, In Press, Corrected Proof,Jun 2013

..respectively. The prepared electrolytes materials are 90% dense which was

measured with He-pycnometry (AccuPyc 1340 Micromeritics, USA). The TGA curves

of the SDC: M 2 CO 3 (M = Na, Li, K) nanocomposite electrolytes are presented...

























http://pubs.rsc.org/en/content/articlelanding/nj/2013/c3nj41117f

http://pubs.rsc.org/en/content/articlelanding/nj/2013/c3nj41117f






Comparison of a xenogeneic and an

alloplastic material used in dental implants in

terms of physico-chemical characteristics and

in vivo inflammatory response

Figueiredo, Andreia / Coimbra, Patrícia / Cabrita,

António / Guerra, Fernando / Figueiredo,

Margarida, Materials Science and Engineering: C,

33 (6), p.3506-3513, Aug 2013

..mercury intrusion porosimetry (Poresizer 9320, Micromeritics Instrument Corp.,

Norcross...pycnometry (Accupyc 1330, Micromeritics Instrument Corp.),

using...adsorption technique (ASAP 2000, Micromeritics Instrument...

Comparison of a xenogeneic and an

alloplastic material used in dental implants in

terms of physico-chemical characteristics and

in vivo inflammatory response

Figueiredo, Andreia / Coimbra, Patrícia / Cabrita,

António / Guerra, Fernando / Figueiredo,

Margarida, Materials Science and Engineering: C,

33 (6), p.3506-3513, Aug 2013

..porosimetry (Poresizer 9320, Micromeritics Instrument Corp...determined by gas

pycnometry (Accupyc 1330, Micromeritics Instrument Corp.), using...adsorption

technique (ASAP 2000, Micromeritics Instrument Corp.) using...

Compressibility and dissolution

characteristics of mixed fruit tablets made

from guava and pitaya fruit powders

Zea, Lai Pei / Yusof, Yus Aniza / Aziz, Mohammad

Gulzarul / Ling, Chin Nyuk / Amin, Nor Amaiza

Mohd, Powder Technology, 247, p.112-119, Oct

2013

..Carr index [12] . The Hausner ratio and Carr index were used to calculate

flowability. A gas pycnometer (AccuPyc II 1340, Micromeritics, Norcross, USA) was

used to determine the absolute density. The particle size of the guava and the

pitaya...

Compression Prediction Accuracy From Small

Scale Compaction Studies To Production

Presses

Pitt, Kendal G. / Hill, Rachael J. Webbera / Kirsty

A. / Dey, Dipankar / J.Gamlen, Michael, Powder

Technology, In Press, Accepted Manuscript,Oct

2013

..3 Density measurements The true density of the compression blends was

measured using helium pycnometry (Accupyc 1330, Micromeritics Instrument

Corporation, U.S.A.). 3 Results and Discussion 3.1 Direct compression formulation

The...

Concentration and particle size distribution

of particulate matter inside tunnel-ventilated

high-rise layer operation houses

Wang-Li, Lingjuan / Cao, Zihan / Li, Qianfeng /

Liu, Zifei / Beasley, David B., Atmospheric

Environment, 66, p.8-16, Feb 2013

..using Eq. (5) with an assumption of the particle shape factor in 1 and with a

particle density of 1.48 g/cm 3 measured by an AccuPyc 1330 Pycnometer. b

Average of three replicates from TSP samples taken by three co-located TSP

samplers. c Average of two replicates...

Consolidation trend design based on Young's

modulus of clarithromycin single crystals

Jankovid, B. / Škarabot, M. / Lavrič, Z. / Ilid, I. /

Muševič, I. / Srčič, S. / Planinšek, O., International

Journal of Pharmaceutics, 454 (1), p.324-332, Sep

2013

..In addition, the true density of powdered Clar forms was measured in triplicate

with a helium pycnometer (AccuPyc 1330, Micromeritics, Norcross, GA, USA).

Compressibility was evaluated using “in-die” Heckel analysis ( Heckel, 1961...

Control of three-dimensional substrate

stiffness to manipulate mesenchymal stem

cell fate toward neuronal or glial lineages

Her, Goh Jih / Wu, Hsi-Chin / Chen, Ming-Hong /

Chen, Ming-Yi / Chang, Shun-Chih / Wang, Tzu-

Wei, Acta Biomaterialia, 9 (2), p.5170-5180, Feb

2013

..replicates. For porosity analysis, three replicates from each group of scaffolds were

measured by using AccuPyc 1330 Pycnometer (Micromeritics, USA). The porosity of

scaffolds was calculated with the following equation: (1) Porosity of scaffolds...

Controlling electron injection and electron

transport of dye-sensitized solar cells aided

by incorporating CNTs into a Cr-doped TiO 2

photoanode

Massihi, N. / Mohammadi, M.R. / Bakhshayesh,

A.M. / Abdi-Jalebi, M., Electrochimica Acta, 111,

p.921-929, Nov 2013

..vis) spectroscopy using a 6705 JENWAY spectrometer. The density of the TiO 2

nanostructures was measured by a Micromeritics AccuPyc 1330 pycnometer

analyzer. Photovoltaic measurements were carried out using a solar simulator under

standard test...

Correlation between processing conditions,

microstructure and charge transport in half-

Heusler alloys

Makongo, Julien P.A. / Zhou, Xiaoyuan / Misra,

Dinesh K. / Uher, Ctirad / Poudeu, Pierre F.P.,

Journal of Solid State Chemistry, 201, p.280-287,

May 2013

..13] . Densities of loose powders and pressed pellets were respectively obtained by

He gas pycnometry using a Micromeritics Accupyc II 1340 and by geometrical

measurements using a digital micrometer. The relative packing densities for all

pellets...































Correlation of microstructure and thermal

conductivity in nanoporous solids: The case

of polyurea aerogels synthesized from an

aliphatic tri-isocyanate and water

Weigold, Lena / Mohite, Dhairyashil P. / Mahadik-

Khanolkar, Shruti / Leventis, Nicholas /

Reichenauer, Gudrun, Journal of Non-Crystalline

Solids, 368, p.105-111, May 2013

..the skeletal density ( ρ solid ), via Eq. (1) . Skeletal density was obtained by helium

pycnometry using a Micromeritics AccuPyc II 1340 instrument. Before analysis,

samples were degassed for 48 h at 80 °C and then stored under vacuum in...

Coupled concentration-dependent

diffusivities of ethanol/water mixtures

through a polymeric membrane: Effect on

pervaporative flux and diffusivity profiles

Yang, Tzu-Huai / Lue, Shingjiang Jessie, Journal of

Membrane Science, 443, p.1-9, Sep 2013

..200±15 μm with a membrane density of 1.090±0.051 g/cm 3 measured using the

pycnometer (model Accupyc II 1340, Micromeritics Inc. Co., Norcross, Georgia,

USA). The characterization of the PDMS membrane has been shown in previous...

Decontamination of metals and polycyclic

aromatic hydrocarbons from slag-polluted soilS Bisone, G Mercier, JF Blais - Environmental

Technology, 2013 - Taylor & Francis

... Elmer, model Clarus 500, with column type Rxi®-17, 30 mx 0.25 mm x 0.25 µm).

10 The soil density was measured by a Micromeritics AccuPyc 1330 Pycnometer

using dry soil 11 samples of approximately 20–25 g. 12 Techno-economic evaluation

13

Deep subsoiling of a subsurface-compacted

typical hapludult under citrus orchardJC Medeiros, GC Figueiredo, ÁL Mafra… - Revista

Brasileira de …, 2013 - SciELO Brasil

... E-mail: [email protected] III Professor, Santa Catarina State University.

Av. Luiz de Camões, 2900. CEP 88520-000 Lages (SC), Brazil. ... The particle density

was evaluated using a helium pycnometer (ACCUPYC 130, Micromeritics Instrument

Corporation TM , USA).

Deformation properties of pharmaceutical

excipients determined using an in-die and

out-die method

Ilid, Ilija / Govedarica, Biljana / Šibanc, Rok / Dreu,

Rok / Srčič, Stane, International Journal of

Pharmaceutics, 446 (1-2), p.6-15, Mar 2013

..Greifensee, Switzerland). True density of tableting mixtures was determined with a

helium pycnometer (AccuPyc 1330, Micromeritics, Norcross, GA, USA).

Compressibility was determined using both in-die and out-die Heckel and Walker...

Degradation of p -nitrophenol and bacteria with TiO 2 xerogels

sensitized in situ with tetra( 4 -carboxyphenyl)porphyrins

Tasseroul, Ludivine / Lambert, Stéphanie D. /

Eskenazi, David / Amoura, Makhlouf / Páez,

Carlos A. / Hiligsmann, Serge / Thonart, Philippe /

Heinrichs, Benoît, Journal of Photochemistry and

Photobiology A: Chemistry, 272, p.90-99, Nov

2013

..in KBr (0.6 wt.% for all samples). Apparent densities, ρ app , were measured by

helium pycnometry on a Micromeritics AccuPyc 1330 device. The pore texture of

the xerogels was examined by nitrogen adsorption–desorption measurements...

Design of ceramic paste formulations for co-

extrusion

Powell, Jonathan / Assabumrungrat, Suttichai /

Blackburn, Stuart, Powder Technology, 245, p.21-

27, Sep 2013

..binder made according to the formulation given in Table 1 was measured using a

constant volume pycnometer (Accupyc 1330, Micromeritics, UK) and was found to

be 1835 kg.m − 3 . This indicates that the constituents, PVB, DBP and stearic...

Determination of texture and transport

characteristics of electrospun nanofibrous

mats

Soukup, K. / Hejtmánek, V. / Petráš, D. / Šolcová,

O., Colloids and Surfaces A: Physicochemical and

Engineering Aspects, 437, p.133-140, Nov 2013

..the ASAP2020M instrument (Micromeritics, USA) by two

independent...AUTOPORE III instrument (Micromeritics, USA) were used for

determination...He was determined on the AccuPyc 1920 instrument

(Micromeritics, USA) and porosity ɛ...

Determination of texture and transport

characteristics of electrospun nanofibrous

mats

Soukup, K. / Hejtmánek, V. / Petráš, D. / Šolcová,

O., Colloids and Surfaces A: Physicochemical and

Engineering Aspects, 437, p.133-140, Nov 2013

..the ASAP2020M instrument (Micromeritics, USA) by two

independent...porosimetry performed on AUTOPORE III instrument (Micromeritics,

USA) were used for determination...AccuPyc 1920 instrument (Micromeritics, USA)

and porosity ɛ...









http://www.tandfonline.com/doi/abs/10.1080/09593330.2013.781231

http://www.tandfonline.com/doi/abs/10.1080/09593330.2013.781231

http://www.scielo.br/scielo.php?pid=S0100-06832013000400008&script=sci_arttext

http://www.scielo.br/scielo.php?pid=S0100-06832013000400008&script=sci_arttext













Determination of the reaction rate

coefficient of sulphide mine tailings

deposited under water

Awoh, Akué Sylvette / Mbonimpa, Mamert /

Bussière, Bruno, Journal of Environmental

Management, 128, p.1023-1032, Oct 2013

..distribution measurements are given by Merkus (2009) . The relative density of

tailings was determined using a Micromeritics Accupyc 1330 helium pycnometer

(the accuracy is to within 0.03% of reading plus 0.03% of nominal full-scale sample...

Economical production of PVDF-g-POEM for

use as a blend in preparation of PVDF based

hydrophilic hollow fibre membranes

Moghareh Abed, M.R. / Kumbharkar, S.C. /

Groth, A.M. / Li, K., Separation and Purification

Technology, 106, p.47-55, Mar 2013

..in DMSO-d 6 . The density of the PVDF powder and the synthesised copolymer was

measured using a pycnometer (Micromeritics Accupyc 1330, Bedfordshire, UK). The

molecular weights of the synthesised copolymer and pure PVDF were determined...

Effect of flaxseed processing on engineering

properties and fatty acids profiles of pasta

Villeneuve, Sébastien / Des Marchais, Louis-

Philippe / Gauvreau, Vanessa / Mercier, Samuel /

Do, Chi Bao / Arcand, Yves, Food and Bioproducts

Processing, 91 (3), p.183-191, Jul 2013

..cups for bulk density measurement. True density was determined in triplicate with

a Helium Gas Pycnometer (AccuPyc II 1340, Micromeritics, Norcross, GA, USA). The

1000-grain weight was determined in triplicate according to method ASBC Barley-

2D...

Effect of operational parameters and stress

energies on the particle size distribution of

TiO 2 pigment in stirred media milling

Ohenoja, Katja / Illikainen, Mirja / Niinimäki,

Jouko, Powder Technology, 234, p.91-96, Jan

2013

..The filling ratio of the grinding media was kept constant at 70 vol.%. 2.3 Analysis A

gas pycnometer (Micromeritics AccuPyc II 1340) was used to measure the densities

of the grinding beads, and a Beckman Coulter LS 13 320 particle size...

Effect of petroleum (pet) coke addition on

the density and thermal conductivity of

cement pastes and mortars

Olmeda, J. / Sánchez de Rojas, M.I. / Frías, M. /

Donatello, S. / Cheeseman, C.R., Fuel, 107, p.138-

146, May 2013

..Pet coke has a density of approximately 1350 kg/m 3 when measured at 26 ± 2 °C

by He picnometry (model Micromeritics Accupyc 1330) and this is much lower than

that of the hydrated cement paste matrix (1900 kg/m 3 ). At 30% addition...

Effect of polymers for aerolization properties

of mannitol-based microcomposites

containing meloxicam

Pomázi, Anita / Buttini, Francesca / Ambrus, Rita

/ Colombo, Paolo / Szabó-Révész, Piroska,

European Polymer Journal, 49 (9), p.2518-2527,

Sep 2013

..parameters: 300RF lens; small volume dispersion unit (1000 rpm); true density of

MX = 1.565 g cm −3 (AccuPyc 1330, Micromeritics, Norcross, USA); 1.596 was taken

as the refractive index for dispersed particles and 1.330 for the dispersion...

Effect of silica nanoparticles on the bulk flow

properties of fine cohesive powders Kojima, Takehiro / Elliott, James A., Chemical

Engineering Science, 101, p.315-328, Sep 2013

..84 µm and σ g =1.31. The particle density of the PS-DVB microspheres measured

by a gas pycnometer (Accupyc 1330, Micromeritics, USA) was 1070 kg m −3 . The

size distribution of PS-DVB microspheres is very similar to those of the...

Effect of temperature on thermochemical

property and true density of torrefied coffee

residue

Tsai, Wen-Tien / Liu, Sii-Chew, Journal of

Analytical and Applied Pyrolysis, 102, p.47-52, Jul

2013

..very small molecule size (about 0.2 nm). A helium displacement method with a

pycnometer (Micromeritics Co., U.S.A.; Model No.: AccuPyc 1340) was used to

measure the true density of the torrefied sample in this work. Although the...

Effect of the addition of waste sawdust on

thermoplastic properties of a coal Montiano, M.G. / Barriocanal, C. / Alvarez, R.,

Fuel, 106, p.537-543, Apr 2013

..was measured by means of helium pycnometry in a Micromeritics Accupyc 1330

Pycnometer. Their apparent density ( ρ Hg ) was determined with mercury at 0.1

MPa in a Micromeritics autopore IV 9500 mercury porosimeter. From the...

Effect of the addition of waste sawdust on

thermoplastic properties of a coal Montiano, M.G. / Barriocanal, C. / Alvarez, R.,

Fuel, 106, p.537-543, Apr 2013

..was measured by means of helium pycnometry in a Micromeritics Accupyc 1330

Pycnometer. Their apparent density...was determined with mercury at 0.1 MPa in a

Micromeritics autopore IV 9500 mercury porosimeter. From the true and...




























Effects of lubricant on green strength,

compressibility and ejection of parts in die

compaction process

Enneti, Ravi K. / Lusin, Adam / Kumar, Sumeet /

German, Randall M. / Atre, Sundar V., Powder

Technology, 233, p.22-29, Jan 2013

..procedure [25] using an Arnold meter. The actual density was measured by helium

pycnometry (Model: Accupyc 1330, Vendor: Micromeritics) and the flowability was

measured by a Hall flow meter [26] . The properties of the powders used in...

Effects of magnesium for calcium

substitution in P 2 O 5 –CaO–TiO 2 glasses

Morikawa, Hiroshi / Lee, Sungho / Kasuga,

Toshihiro / Brauer, Delia S., Journal of Non-

Crystalline Solids, 380, p.53-59, Nov 2013

..theor = 2 M 2 I O + M II O + 2 M IV O 2 P 2 O 5 − 1 Glass density was measured

using a helium pycnometer (AccuPyc 1330-1000, Micromeritics GmbH, Aachen,

Germany); the estimated error limits are ± 0.01 g cm − 3 . Oxygen density was

calculated...

Efficiently trapping asphaltene-type materials

from direct coal liquefaction residue using

alkylsulfate-based ionic liquids

L Bai, Y Nie, J Huang, Y Li, H Dong, X Zhang - Fuel,

2013 - Elsevier

... The true densities of extracts were tested on a full-automatic true density type

analyzer AccuPycII1340 (Micromeritics, America) at room temperature. ... The

bands near 2920 cm −1 and 2855 cm −1 are due to aliphatic C H stretching

vibrations, which indicated that these extracts

Electrical monitoring of crack propagation

during quasi-static loading and ballistic

impact of alumina plates

Oberg, E.K. / Dunleavy, C.S. / Bourke, P. / Clyne,

T.W., Journal of the European Ceramic Society,

33 (13-14), p.2663-2675, Nov 2013

..porosity level is significantly higher in the low purity material. The density was

measured by He-Pycnometry, using a Micro Meritics AccuPyc 1330, and by

hydrostatic weighing in liquid C 11 H 20 . The Young's modulus (assumed isotropic)

was estimated...

Elemental distribution, solute solubility and

defect free volume in nanocrystalline

restricted-equilibrium Cu–Ag alloys

T Riedl / A Kirchner / K Eymann / A Shariq / R

Schlesiger / G Schmitz / M Ruhnow / B Kieback ,

Journal of Physics: Condensed Matter, 25 (11),

p.115401, Mar 2013

..Pore areas were evaluated with standard image-analysis software. Density

measurements were accomplished with a Micromeritics Accupyc 1330 He gas

pycnometer. For phase and strain analysis, x-ray diffraction (XRD) using a Bruker D8

Discover...

Elevated Pressure CO 2 Adsorption

Characteristics of K-promoted Hydrotalcites

for Pre-combustion Carbon Capture

Li, Shuang / Shi, Yixiang / Yang, Yi / Cai,

Ningsheng, Energy Procedia, 37, p.2224-2231,

Jan 2013

..determined by true density and tap density in our calculation, where the true

density is measured by a pycnometer (Micromeritics, AccuPyc 1330). Thus, we take

the true density instead of particle density, and calculation porosity cal instead of...

ENERGETIC SALTS: DEGRADATION AND

TRANSFORMATIONS Vadlamannati - 2013 - digitalcommons.uri.edu

... 3]. 2.2 Densities, Solubility and Melting Points of UN and NU Ten density

determinations for UN and NU products were obtained using a Micromeritics

AccuPyc 1340 gas pycnometer. For each determination a sample cup (1.0

Equilibrium and kinetic studies on acid dye

Acid Red 88 adsorption by magnetic ZnFe 2 O

4 spinel ferrite nanoparticles

Konicki, Wojciech / Sibera, Daniel / Mijowska,

Ewa / Lendzion-Bieluo, Zofia / Narkiewicz,

Urszula, Journal of Colloid and Interface Science,

398, p.152-160, May 2013

..by the Brunauer–Emmett–Teller (BET) method using the equipment Gemini 2360

of Micromeritics. The helium pycnometer AccuPyc 1330 of Micromeritics was

applied to determine the density of powders. The functional groups on the MNZnFe

surface...

Equilibrium and kinetic studies on acid dye

Acid Red 88 adsorption by magnetic ZnFe 2 O

4 spinel ferrite nanoparticles

Konicki, Wojciech / Sibera, Daniel / Mijowska,

Ewa / Lendzion-Bieluo, Zofia / Narkiewicz,

Urszula, Journal of Colloid and Interface Science,

398, p.152-160, May 2013

..determined by the Brunauer–Emmett–Teller (BET) method using the equipment

Gemini 2360 of Micromeritics. The helium pycnometer AccuPyc 1330 of

Micromeritics was applied to determine the density of powders. The functional

groups on the MNZnFe...

Evaluation of mechanical and physical

properties of industrial particleboard bonded

with a corn flour–urea formaldehyde

adhesive

Moubarik, Amine / Mansouri, Hamid Reza / Pizzi,

Antonio / Allal, Ahmed / Charrier, Fatima / Badia,

Miguel Angel / Charrier, Bertrand, Composites

Part B: Engineering, 44 (1), p.48-51, Jan 2013

..by measuring the mass and volume, while material density of the board was

measured with a Helium Pycnometer Accupyc 1330 (Micromeritics, USA). Porosity

was given by Rahman equation *23,24+ : e = 1 - ρ ap ρ m where e , ρ ap and ρ m

are...


















http://digitalcommons.uri.edu/oa_diss/108/

http://digitalcommons.uri.edu/oa_diss/108/












Evaluation on Properties of CaO–BaO–B 2 O 3

–Al 2 O 3 –SiO 2 Glass–Ceramic Sealants for

Intermediate Temperature Solid Oxide Fuel

Cells

Heydari, Fatemeh / Maghsoudipour, Amir /

Hamnabard, Zohreh / Farhangdoust, Sajad,

Journal of Materials Science & Technology, 29

(1), p.49-54, Jan 2013

..method (ASTM.C474-88) and powder density of the samples was measured with a

helium gas pycnometer (model Accupyc 1330, Micromeritics, Norcross, GA). The

relative density of the sintered specimens was determined by dividing bulk density

by...

Expansion of nanosized pores in low-

crystallinity nanoparticle-assembled plates

via a thermally induced increase in solid-state

density

Okada, Masahiro / Fujiwara, Keiko / Uehira,

Mayo / Matsumoto, Naoyuki / Takeda, Shoji,

Journal of Colloid and Interface Science, 405,

p.58-63, Sep 2013

..mercury intrusion porosimetry (AutoPore IV 9520; Micromeritics Instrument Corp.,

Norcross, GA), after the...samples were determined using helium pycnometry

(AccuPyc 1330; Micromeritics Instrument Corp.), after the samples were ground...

Expansion of nanosized pores in low-

crystallinity nanoparticle-assembled plates

via a thermally induced increase in solid-state

density

Okada, Masahiro / Fujiwara, Keiko / Uehira,

Mayo / Matsumoto, Naoyuki / Takeda, Shoji,

Journal of Colloid and Interface Science, 405,

p.58-63, Sep 2013

..determined using mercury intrusion porosimetry (AutoPore IV 9520; Micromeritics

Instrument Corp., Norcross, GA), after the...determined using helium pycnometry

(AccuPyc 1330; Micromeritics Instrument Corp.), after the samples were...

Fabrication of modified lithium orthosilicate

pebbles by addition of titania

Knitter, R. / Kolb, M.H.H. / Kaufmann, U. /

Goraieb, A.A., Journal of Nuclear Materials, 442

(1-3 Supplement 1), p.S433-S436, Nov 2013

..of 40 pebbles with a diameter of 1 mm. The material density of the pebbles was

measured by He pycnometry (AccuPyc 1330, Micromeritics) and the closed porosity

was calculated by considering the theoretical density of each composition. 3

Results...

Fabrication of the carbon paper by wet-laying

of ozone-treated carbon fibers with

hydrophilic functional groups

Kim, Hyunuk / Lee, Young-Ju / Lee, Dong-Chul /

Park, Gu-Gon / Yoo, Yoonjong, Carbon, 60, p.429-

436, Aug 2013

..ozone-treated CFs determined using helium pycnometry with a Micromeritics

AccuPyc II 1340 instrument is 1.93...mercury intrusion porosimetry (AutoPore IV

9500, Micromeritics). The CP from ozone-treated CFs showed higher...

Fabrication of the carbon paper by wet-laying

of ozone-treated carbon fibers with

hydrophilic functional groups

Kim, Hyunuk / Lee, Young-Ju / Lee, Dong-Chul /

Park, Gu-Gon / Yoo, Yoonjong, Carbon, 60, p.429-

436, Aug 2013

..CFs determined using helium pycnometry with a Micromeritics AccuPyc II 1340

instrument is...was measured by mercury intrusion porosimetry (AutoPore IV 9500,

Micromeritics). The CP from ozone-treated CFs showed higher...

Facile fabrication of Pickering emulsion

polymerized polystyrene/laponite composite

nanoparticles and their electrorheology

Kim, Young Jae / Liu, Ying Dan / Choi, Hyoung Jin

/ Park, Soo-Jin, Journal of Colloid and Interface

Science, 394, p.108-114, Mar 2013

..lower than that of pure laponite clay. On the other hand, the density measured

using a gas pyconometer (AccuPyc 1330, Micromeritics Instrucments Co., USA) was

1.19 g cm −3 , which is similar to the calculated density from the TGA analysis...

Filler aggregation as a reinforcement

mechanism in polymer nanocomposites

Dorigato, Andrea / Dzenis, Yuris / Pegoretti,

Alessandro, Mechanics of Materials, 61, p.79-90,

Jul 2013

..and nanofillers are reported in Table 1 . Density measurements were performed at

ambient temperature by using a Micromeritics Accupyc® 1330 helium pycnometer,

while surface area and porosity measurements were conducted by using an ASAP®

2010...

Flow and mixing efficiency characterisation in

a CO2-assisted single-screw extrusion process

by residence time distribution using Raman

spectroscopy

Common, Audrey / Rodier, Elisabeth / Sauceau,

Martial / Fages, Jacques, Chemical Engineering

Research and Design, In Press, Accepted

Manuscript,Oct 2013

..defined by: (13) S p i c = ∫ 0 ∞ I ( t ) d t 3.5 Sample characterisation Water and

helium pycnometry (Micromeritics, AccuPYC 1330) were used to determine

respectively, overall and closed porosity. The characterization of the porosity...































Fluidized bed agglomeration of skim milk

powder: Analysis of sampling for the follow-

up of agglomerate growth

Turchiuli, Christelle / Smail, Ramdane /

Dumoulin, Elisabeth, Powder Technology, 238,

p.161-168, Apr 2013

..2 mm (5 min) (density tester, Varian, Fr). Particle true density was measured with

an air pycnometer (Accupyc, Micromeretics, Fr). Flowability was estimated from the

Carr and Hausner indexes (Carr index = ρ tapped /ρ bulk ; Hausner index...

Formation of TbCu 7 -type CeFe 10 Zr 0.8 by

rapid solidification

Zhou, Chen / Pinkerton, Frederick E. / Herbst, Jan

F., Journal of Alloys and Compounds, 569, p.6-8,

Aug 2013

..and cooling in the same Perkin Elmer TGA7 system under magnetic force. Density

was measured on powders using a Micromeritics AccuPyc II gas pycnometer. X-ray

diffraction patterns for the as-spun and annealed samples were collected in a

Rigaku...

Formulation of bioadhesive

hexylaminolevulinate pellets intended for

photodynamic therapy in the treatment of

cervical cancer

Hiorth, Marianne / Liereng, Linda / Reinertsen,

Reidun / Tho, Ingunn, International Journal of

Pharmaceutics, 441 (1-2), p.544-554, Jan 2013

..density of the pellets The true density of the pellet formulations was determined

with a helium gas pycnometer (AccuPyc 1330, Micromeritics Instrument

Corporation, Norcross, GA, USA). Reported results were the mean of three

independent experiments...

Functional poly(urethane-imide)s containing

Lewis bases for SO 2 detection by Love

surface acoustic wave gas micro-sensors

Ben Youssef, Ismaïl / Alem, Halima / Sarry,

Frédéric / Elmazria, Omar / Jimenez Rioboo,

Rafael / Arnal-Hérault, Carole / Jonquières, Anne,

Sensors and Actuators B: Chemical, 185, p.309-

320, Aug 2013

..PTFE plate, small polymer disks were cut using a sharp die. Density measurements

were carried out with a helium Micromeritics AccuPyc 1330 gas pycnometer using

ca. 300 mg of pieces of polymeric films (film thickness: ca. 40 μm). Thermal...

Fused calcium zirconate for refractory

applications

Schafföner, Stefan / Aneziris, Christos G. / Berek,

Harry / Hubálková, Jana / Priese, Angelika,


16), p.3411-3418, Dec 2013

..and the solid state synthesized CaZrO 3 were investigated regarding the true

density in a helium pycnometer (Accupyc 1330, Micromeritics GmbH, Aachen,

Germany) according to the standard DIN 66137-2. In a next step test cylinders (50

mm...

Glass formation, physicochemical

characterization and photoluminescence

properties of new Sb 2 O 3 –PbO–ZnO and Sb

2 O 3 –PbO–ZnS systems

Nouadji, M. / Ivanova, Z.G. / Poulain, M. /

Zavadil, J. / Attaf, A., Journal of Alloys and

Compounds, 549, p.158-162, Feb 2013

..C for 8 h and cooled down in the annealing furnace. The density was determined

using a helium picnometer (Micromeritics, AccuPyc 1330), with ±0.001 g/cm 3

accuracy. The microhardness values were taken by Matzuzawa MXT 70 digital

microhardness...

High temperature structural and magnetic

properties of cobalt nanorods

Ait Atmane, Kahina / Zighem, Fatih / Soumare,

Yaghoub / Ibrahim, Mona / Boubekri, Rym /

Maurer, Thomas / Margueritat, Jérémie / (...) /

Viau, Guillaume, Journal of Solid State Chemistry,

197, p.297-303, Jan 2013

..respectively 0.26 g and 2.13 g cm –3 . The true density of the powder, obtained at

298 K using a helium Accupyc 1330 pycnometer from Micromeritics, was found to

be 6.76±0.41 g cm –3 . The packing factor, defined as the ratio of the volume...

Highly biocompatible, nanocrystalline

hydroxyapatite synthesized in a solvothermal

process driven by high energy density

microwave radiation

Smolen, Dariusz / Chudoba, Tadeusz / Malka,

Iwona / Kedzierska, Aleksandra / Lojkowski,

Witold / Swieszkowski, Wojciech / Kurzydlowski,

Krzysztof Jan / (...) / Lewandowska-Szumiel,

Małgorzata, International Journal of

Nanomedicine, 8, p.653-668, Jan 2013

..performed using a helium pycnometer (AccuPyc, model 1330; Micromeritics,

Gosford, Australia) using an in-house...powders was measured by the BET method

(AccuPyc, model Gemini 2360; Micromeritics). The average diameter of the

particles...


























Highly biocompatible, nanocrystalline

hydroxyapatite synthesized in a solvothermal

process driven by high energy density

microwave radiation

Smolen, Dariusz / Chudoba, Tadeusz / Malka,

Iwona / Kedzierska, Aleksandra / Lojkowski,

Witold / Swieszkowski, Wojciech / Kurzydlowski,

Krzysztof Jan / (...) / Lewandowska-Szumiel,

Małgorzata, International Journal of

Nanomedicine, 8, p.653-668, Jan 2013

..using a helium pycnometer (AccuPyc, model 1330; Micromeritics, Gosford,

Australia) using an in-house procedure...was measured by the BET method

(AccuPyc, model Gemini 2360; Micromeritics). The average diameter of the particles

was...

HydrSothermal treatment kinetics of tannin

for producing carbonaceous microspheres

Braghiroli, F.L. / Fierro, V. / Izquierdo, M.T. /

Parmentier, J. / Pizzi, A. / Celzard, A., Bioresource

Technology, In Press, Accepted Manuscript,Oct

2013

..3 ), was measured by helium pycnometry (Accupyc II 1340, Micromeritics, USA) for

all samples after HTC. Samples were...determined by krypton adsorption at -196°C

using a Micromeritics ASAP 2020 automatic apparatus. Samples were...

Indium doped niobium phosphates as

intermediate temperature proton conductors

Huang, Yunjie / Li, Qingfeng / Anfimova, Tatiana

V. / Christensen, Erik / Yin, Min / Jensen, Jens

Oluf / Bjerrum, Niels J. / Xing, Wei, International

Journal of Hydrogen Energy, 38 (5), p.2464-2470,

Feb 2013

..SEM) measurements were performed on a Carl Zeiss EVO MA10 microscope. The

density of powder was measured by Micromeritics AccuPyc 1330. 2.2.2 Conductivity

measurement For conductivity measurements, the phosphate powders were first

pressed...

Influence of MCC II fraction and storage

conditions on pellet properties

Krueger, Cornelia / Thommes, Markus /

Kleinebudde, Peter, European Journal of

Pharmaceutics and Biopharmaceutics, In Press,

Corrected Proof,Jul 2013

..6 Porosity, shrinking The helium density ( ρ He ) of the pellets was determined by a

helium pycnometer (AccuPyc, Micromeritics, Moenchengladbach, Germany). For

each tested pellet batch, three samples were analyzed. The apparent density...

Influence of Ni nanoparticle addition and

spark plasma sintering on the TiNiSn–Ni

system: Structure, microstructure, and

thermoelectric properties

Birkel, Christina S. / Douglas, Jason E. / Lettiere,

Bethany R. / Seward, Gareth / Zhang, Yichi /

Pollock, Tresa M. / Seshadri, Ram / Stucky, Galen

D., Solid State Sciences, 26, p.16-22, Dec 2013

..molar heat capacity, C p = 3 R , were utilized. Densities were obtained on the same

pieces using a pycnometer (Micromeritics AccuPyc 1330 Pycnometer) and were

found to be ≥99% of the theoretical density. For microstructural investigations...

Influence of powder characteristics on the

behaviour of PIM feedstock

Bricout, Julien / Gelin, Jean-Claude / Ablitzer,

Carine / Matheron, Pierre / Brothier, Meryl,

Chemical Engineering Research and Design, In

Press, Corrected Proof,Mar 2013

..13,320 particle size analyser), pycnometer density (obtained by with Micromeritics

AccuPyc II 1340), the Specific surface area (obtained by Micromeritics ASAP2020),

and the apparent and tap density (NF EN ISO 3953). Scanning Electron...

Influence of process parameters and

equipment on dry foam formulation

properties using indomethacin as model drug

Sprunk, Angela / Page, Susanne / Kleinebudde,

Peter, International Journal of Pharmaceutics,

455 (1-2), p.189-196, Oct 2013

..density ( ρ ), determined by AccuPyc 1330 V3.03 (Micromeritics, USA), tablet

volume ( V...analysis using a SmartPrep (Micromeritics, USA). The adsorbed

amount...using a Gemini 2375 V4.02 (Micromeritics, USA). SSA was calculated...

Influence of process parameters and

equipment on dry foam formulation

properties using indomethacin as model drug

Sprunk, Angela / Page, Susanne / Kleinebudde,

Peter, International Journal of Pharmaceutics,

455 (1-2), p.189-196, Oct 2013

..by AccuPyc 1330 V3.03 (Micromeritics, USA), tablet volume ( V...analysis using a

SmartPrep (Micromeritics, USA). The adsorbed amount...p 0 in duplicates using a

Gemini 2375 V4.02 (Micromeritics, USA). SSA was calculated...
























Influence of the membrane treatment on

structure and properties of sulfonated

poly(etheretherketone) semi-

interpenetrating polymer network

Delhorbe, Virginie / Cailleteau, Céline / Chikh,

Linda / Guillermo, Armel / Gebel, Gérard / Morin,

Arnaud / Fichet, Odile, Journal of Membrane

Science, 427, p.283-292, Jan 2013

..thicknesses of the dry and wet membranes, respectively. Density measurements

were performed with a Accupyc II 1340 gas pycnometer from Micromeritics. All

samples were dried 12 h at 40 °C under vacuum prior to measurements. Pulse Field

Gradient...

Influence of thermoplastic properties on

coking pressure generation: Part 3 – Evidence

and role of pore coalescence in the

mechanism for pressure generation

Duffy, John J. / Scholes, Oliver / Mahoney,

Merrick R. / Steel, Karen M., Fuel, 103, p.711-

718, Jan 2013

..coke samples (approximately 0.2 g) using a Micromeritics Autopore IV

Porosimeter. Tests were performed...pycnometry Helium pycnometry was

performed using a Micromeritics Accupyc 1330 Pycnometer with 10 cm 3 sample

holder. Prior...

Influence of thermoplastic properties on

coking pressure generation: Part 3 – Evidence

and role of pore coalescence in the

mechanism for pressure generation

Duffy, John J. / Scholes, Oliver / Mahoney,

Merrick R. / Steel, Karen M., Fuel, 103, p.711-

718, Jan 2013

..coke samples (approximately 0.2 g) using a Micromeritics Autopore IV

Porosimeter. Tests were performed in two...pycnometry Helium pycnometry was

performed using a Micromeritics Accupyc 1330 Pycnometer with 10 cm 3 sample

holder...

Interactions of heat and mass transfer in

steam reheating of starchy foods

Huang, Shih-Rong / Yang, Jing-Iong / Lee, Yeun-

Chung, Journal of Food Engineering, 114 (2),

p.174-182, Jan 2013

..density method ( Rahman, 2009 ). The true volume of freeze dried steamed bun

was measured by using the AccuPyc 1340 Pyconmeter (Micromeritics, Georgia) and

helium was used as a displaced fluid to ensure the best accuracy. Water was

assumed...

Jet mill grinding of portland cement,

limestone, and fly ash: Impact on particle

size, hydration rate, and strength

Sun, Hongfang / Hohl, Brian / Cao, Yizheng /

Handwerker, Carol / Rushing, Todd S. / Cummins,

Toney K. / Weiss, Jason, Cement and Concrete

Composites, 44, p.41-49, Nov 2013

..32] . Methanol was used as a dispersant. The densities required for PSD calculation

were measured by a Micromeritics Accupyc 1330 pycnometer. All mortars were

prepared in a Hobart mixer following ASTM C 305. After casting, the specimens...

LAS glass–ceramic scaffolds by three-

dimensional printing

Zocca, Andrea / Gomes, Cynthia M. / Bernardo,

Enrico / Müller, Ralf / Günster, Jens / Colombo,

Paolo, Journal of the European Ceramic Society,

33 (9), p.1525-1533, Aug 2013

..saturated and suspended mass, while the density of the crystallized powder was

measured with a pycnometer (AccuPyc 1340, Micromeritics Italia, Milano, Italy). 3

Results and discussion 3.1 Characterization of the glass–ceramic powder...

Lignin–phenol–formaldehyde aerogels and

cryogels

Grishechko, L.I. / Amaral-Labat, G. / Szczurek, A. /

Fierro, V. / Kuznetsov, B.N. / Celzard, A.,

Microporous and Mesoporous Materials, 168,

p.19-29, Mar 2013

..Envelope Density Analyser (Micromeritics, USA). A quantity of DryFlo...was

measured with an Accupyc II 1340 helium pycnometer (Micromeritics, USA). For

avoiding errors related...adsorption apparatus (Micromeritics, USA). The samples

were...

Local microarchitecture affects mechanical

properties of deposited extracellular matrix

for osteonal regeneration

Pilia, M. / Guda, T. / Pollot, B. / Aguero, V. /

Appleford, M., Materials Science and

Engineering: C, In Press, Accepted

Manuscript,Oct 2013

..volume fraction of the scaffold. True solid volumes of the scaffolds were measured

using helium pycnometry (AccuPyc 1340, Micromeritics, Norcross, GA). The length

and diameter of each scaffold were measured by averaging across three

independent...

Local solidosity of microcrystalline cellulose

during dead-end filtration and sedimentation

Mattsson, Tuve / Martínez, Eduard Laguarda /

Sedin, Maria / Theliander, Hans, Chemical

Engineering Research and Design, 91 (6), p.1155-

1162, Jun 2013

..method), with nitrogen as the adsorption gas (Micromeritics Tristar 3000); the

particle size distribution...and the solid density was determined using a

Micromeritics Accupyc 1330. The shape of the particles was investigated...





http://www.researchgate.net/publication/256712157_Influence_of_thermoplastic_properties_on_coking_pressure_generation_Part_3__Evidence_and_role_of_pore_coalescence_in_the_mechanism_for_pressure_generation























Local solidosity of microcrystalline cellulose

during dead-end filtration and sedimentation

Mattsson, Tuve / Martínez, Eduard Laguarda /

Sedin, Maria / Theliander, Hans, Chemical

Engineering Research and Design, 91 (6), p.1155-

1162, Jun 2013

..method), with nitrogen as the adsorption gas (Micromeritics Tristar 3000); the

particle size distribution was measured...and the solid density was determined using

a Micromeritics Accupyc 1330. The shape of the particles was investigated...

Low sintering temperature of ZnNb 2 O 6 for silver co-sintering

Quercioli, Regis / Bernard, Jerome / Haussonne,

Jean-Marie / Reboul, Jean-Michel / Houivet,

David, Ceramics International, In Press, Corrected

Proof,Jul 2013

..SEM, and BET specific surface measurements were made with a Micromeritics

TriStarII. Glass frits were added to ZnNb 2 O 6 with...analysed by XRD and their

density was measured with Micrometrics AccuPyc 1330 He pycnometer. Open

porosity was estimated by calculating...

Macadamia nut shell-derived carbon

composites for post combustion CO 2 capture Bae, Jun-Seok / Su, Shi, International Journal of

Greenhouse Gas Control, 19, p.174-182, Nov 2013

..out using volumetric gas adsorption analyzers (Micromeritics TriStar 3000 and

ASAP2020HD). The helium densities...carbons were measured using a helium

pycnometer (Micromeritics AccuPyc 1340). The MPSDs of samples were obtained

from...

Macadamia nut shell-derived carbon

composites for post combustion CO 2 capture Bae, Jun-Seok / Su, Shi, International Journal of

Greenhouse Gas Control, 19, p.174-182, Nov 2013

..out using volumetric gas adsorption analyzers (Micromeritics TriStar 3000 and

ASAP2020HD). The helium densities of...carbons were measured using a helium

pycnometer (Micromeritics AccuPyc 1340). The MPSDs of samples were obtained...

Magnetic susceptibility and hardness of Au –x

Pt –y Nb alloys for biomedical applications

Uyama, Emi / Inui, Shihoko / Hamada, Kenichi /

Honda, Eiichi / Asaoka, Kenzo, Acta Biomaterialia,

9 (9), p.8449-8453, Sep 2013

..v was not calculated. The specimen volume was measured five times for each

specimen using a gas pycnometer (Accupyc 1330, Micromeritics Instrument Corp.,

USA) at RT. χ v was calculated from these two data. 2.3 Vickers hardness and

phase...

Measurements and Design Calculations for a

Deep Coaxial Borehole Heat Exchanger in

Aachen, Germany

Dijkshoorn, Lydia / Speer, Simon / Pechnig,

Renate, International Journal of Geophysics,

2013, p.1-14, Jan 2013

..geophysical logs. Matrix density of the cuttings (Figure 3) is measured with a

helium gas pycnometer (Accupyc by Micromeritics [3]). The device calculates the

matrix density from the amount of helium saturating the pores of the dried...

Mechanistic characterization of bilayer tablet

formulations

Akseli, Ilgaz / Abebe, Admassu / Sprockel, Omar /

Cuitiño, Alberto M., Powder Technology, 236,

p.30-36, Feb 2013

..behavior seen with pharmaceutical materials. The true densities of powders were

measured by helium pycnometry (AccuPyc 1330, Micromeritics Instrument Corp.,

Norcross, GA) in triplicate using fresh samples each time. For MCC and

pregelatinized...

Mercury(II) removal from aqueous solution

by sorption onto alginate, pectate and

polygalacturonate calcium gel beads. A

kinetic and speciation based equilibrium study

Cataldo, Salvatore / Gianguzza, Antonio /

Pettignano, Alberto / Villaescusa, Isabel, Reactive

and Functional Polymers, 73 (1), p.207-217, Jan

2013

..values were measured by a pycnometer at T = 20 °C. Further measurements were

done with a helium pycnometer (Micromeritics AccuPyc 1330) in order to confirm

the density values previously obtained. The water content and the weight swelling

ratio...

Microstructural investigations of natural and

synthetic graphites and semi-graphites

Rodrigues, Sandra / Marques, Manuela / Suárez-

Ruiz, Isabel / Camean, Ignacio / Flores, Deolinda /

Kwiecinska, Barbara, International Journal of Coal

Geology, 111, p.67-79, May 2013

..Helium density and chemical analysis Density measurements of the samples were

made with a Helium Pycnometer Accupyc 1330 from Micromeritics. For this

purpose the samples were degassed at 100 °C and held overnight in vacuum. The

overall error...









http://www.hindawi.com/journals/ijge/2013/916541/












Microstructure and mechanical properties of

Ni/10 mol% Sc 2 O 3 –1 mol% CeO 2 –ZrO 2

cermet anode for solid oxide fuel cells

Chen, Yan / Orlovskaya, Nina / Graule, Thomas /

Kuebler, Jakob, Journal of the European Ceramic

Society, 33 (3), p.557-564, Mar 2013

..reduction were measured using mercury porosimetry (Pascal 140 and 440,

POROTEC, Italy) and He-pycnometry (AccuPyc 1330, Micromeritics, USA). The

specific surface areas were determined using N 2 adsorption isotherm by BET

measurements (Beckman-Coulter...

Mixed alkali effects in Bioglass® 45S5 Tylkowski, M. / Brauer, D.S., Journal of Non-

Crystalline Solids, 376, p.175-181, Sep 2013

..Density (ρ glass ) was measured on glass monoliths (approximately 10 g in weight)

in a helium pycnometer (AccuPyc 1330-1000, Micromeritics GmbH, Aachen,

Germany). The estimated error limits are ± 0.01 g cm − 3 . Oxygen density was

calculated...

Mixed matrix membranes containing MOFs

for ethylene/ethane separation Part A:

Membrane preparation and characterization

Ploegmakers, Jeroen / Japip, Susilo / Nijmeijer,

Kitty, Journal of Membrane Science, 428, p.445-

453, Feb 2013

..663 FeBTC 1300–1600 – 1.677 MIL-53 1100–1500 31.55 1.642 ⁎ Experimentally

determined with Micromeritics AccuPyc 1330 pycnometer. Table 2 Fit results of the

sorption isotherms of ethylene and ethane using the Sips model for...

Mixed matrix membranes containing MOFs

for ethylene/ethane separation—Part B:

Effect of Cu 3 BTC 2 on membrane transport

properties

Ploegmakers, Jeroen / Japip, Susilo / Nijmeijer,

Kitty, Journal of Membrane Science, 428, p.331-

340, Feb 2013

..was calculated from the volume of the sample (calculated from the density of the

sample as determined using a Micromeritics AccuPyc 1330 pycnometer at 26.0±0.8

°C), the mass uptake of gas of the sample, and the molar volume and molecular...

Mixing variables for prebaked anodes used in

aluminum production

Azari, Kamran / Alamdari, Houshang / Aryanpour,

Gholamreza / Picard, Donald / Fafard, Mario /

Adams, Angelique, Powder Technology, 235,

p.341-348, Feb 2013

..and a helium pycnometer (Micromeritics, AccuPyc II 1340) was used to

measure...100 A mercury porosimeter (Micromeritics, AutoPore IV) was used

to...measured using BET method (Micromeritics, TriStar II). 3 Results...


aluminum production




p.341-348, Feb 2013

..and a helium pycnometer (Micromeritics, AccuPyc II 1340) was used...100 A

mercury porosimeter (Micromeritics, AutoPore IV) was used to measure

the...measured using BET method (Micromeritics, TriStar II). 3 Results...


aluminum production




p.341-348, Feb 2013

..and a helium pycnometer (Micromeritics, AccuPyc II 1340) was used...100 A

mercury porosimeter (Micromeritics, AutoPore IV) was used to...measured using

BET method (Micromeritics, TriStar II). 3 Results 3.1 Green...

Modelling and optimizing the gas-lift effect

system for texturing silicon M Amouzgar / M Kahrizi , Journal of Physics D:

Applied Physics, 46 (13), p.135107, Apr 2013

..viscosity was measured using a Paar Phisica MCR 500 Rheometer. The density of

the liquid was measured using a Micromeritics Accupyc II 1340 Pycnometer. The

average velocity in the GLE system was calculated by measuring the time it took a

red...

Modifications on Microporosity and Physical

Properties of Cement Mortar Caused by

Carbonation: Comparison of Experimental ...

Pham, Son Tung, Advances in Materials Science

and Engineering, 2013, p.1-9, Jan 2013

..layers. The specific surface area analyser Micromeritics Gemini VII was used for

this test. From adsorption...volume of the sample using the ideal gas law.

Micromeritics helium pycnometer AccuPyc II 1340 was used for this measurement.

...








http://yadda.icm.edu.pl/yadda/element/bwmeta1.element.elsevier-d7198de8-872e-3276-8e98-027fa0751f08










http://iopscience.iop.org/0022-3727/46/13/135107

http://iopscience.iop.org/0022-3727/46/13/135107

http://www.hindawi.com/journals/amse/2013/672325/




Modifications on Microporosity and Physical

Properties of Cement Mortar Caused by

Carbonation: Comparison of Experimental ...

Pham, Son Tung, Advances in Materials Science

and Engineering, 2013, p.1-9, Jan 2013

..the layers. The specific surface area analyser Micromeritics Gemini VII was used for

this test. From adsorption desorption...actual volume of the sample using the ideal

gas law. Micromeritics helium pycnometer AccuPyc II 1340 was used for this...

MOF and UiO-67/MCM-41 adsorbents for

pre-combustion CO 2 capture by PSA:

Breakthrough experiments and process

design

Casas, Nathalie / Schell, Johanna / Blom, Richard

/ Mazzotti, Marco, Separation and Purification

Technology, 112, p.34-48, Jul 2013

..been produced. The material density and the particle density have been

characterized by Helium pycnometery (AccuPyc 1330, Micromeritics, Brussels,

Belgium) and by Hg-pycnometery (Pascal 140 and Pascal 440, Thermo Fisher

Scientific, Reinach...

Molten salt synthesis and characterization of

SiC coated carbon black particles for

refractory castable applications

Ye, Jianke / Zhang, Shaowei / Lee, William E.,

Journal of the European Ceramic Society, 33 (10),

p.2023-2029, Sep 2013

..CB and as-prepared SiC coated CB after ultrasonic dispersion were determined

using a Helium Pycnometer (AccuPyc II 1340, Micromeritics Instruments). Zeta

potential values were measured using a ZetaProbe Analyzer (Colloidal Dynamics Pty

Ltd...

Morphological and Cell Growth Assessment

in Near Dense Hydroxyapatite Scaffold

Wiria, Florencia Edith / Tay, Bee Yen /

Ghassemieh, Elaheh, Journal of Materials, 2013,

p.1-8, Jan 2013

..porosity of the scaffold was indirectly calculated from the sample’s true volume,

measured using a pycnometer (Micromeritics, AccuPyc 1330). Ten samples were

used for the measurement ( ). 2.3. Hardness Measurement Hardness

measurement...

New chemically reworkable epoxy coatings

obtained by the addition of polyesters with

star topologies to diglycidyl ether of

bisphenol A resins

Tomuta, Adrian M. / Ramis, Xavier / Fernández-

Francos, Xavier / Ferrando, Francesc / Serra,

Angels, Progress in Organic Coatings, 76 (11),

p.1616-1624, Nov 2013

..and 100.6 MHz 13 C NMR spectra were obtained with a Varian Gemini 400

spectrometer with Fourier transformed. 1 H NMR spectra...materials before and

after curing, which were determined using a Micromeritics AccuPyc 1330 Gas

Pycnometer thermostatized at 40 °C. The...

New chemically reworkable epoxy coatings

obtained by the addition of polyesters with

star topologies to diglycidyl ether of

bisphenol A resins

Tomuta, Adrian M. / Ramis, Xavier / Fernández-

Francos, Xavier / Ferrando, Francesc / Serra,

Angels, Progress in Organic Coatings, 76 (11),

p.1616-1624, Nov 2013

..shrinkage was calculated from the densities of the materials before and after

curing, which were determined using a Micromeritics AccuPyc 1330 Gas

Pycnometer thermostatized at 40 °C. The shrinkage during curing was determined

as: (3) % shrinkage...

New electrorheological fluid obtained from

mercaptosilsesquioxane-modified silicate

suspensions

Marins, Jéssica A. / Dahmouche, Karim / Soares,

Bluma G., Materials Science and Engineering: C,

33 (1), p.133-139, Jan 2013

..2.4 Sample characterization The density of SiO 2 /SSQ-SH was determined by using

a helium picnometric of Micromeritics AccuPyc 133Q V2.03N, at 25 °C. Fourier

transform infrared spectra by KBr pellet were recorded in a Bruker spectrometer...

New insight into artifactual phenomena

during in vitro toxicity assessment of

engineered nanoparticles: Study of TNF-α

adsorption on alumina oxide nanoparticle

Pailleux, Mélanie / Boudard, Delphine / Pourchez,

Jérémie / Forest, Valérie / Grosseau, Philippe /

Cottier, Michèle, Toxicology in Vitro, 27 (3),

p.1049-1056, Apr 2013

..adsorption at 77 K after out-gassing for 2 h at 200 °C (Micromeritics ASAP 2000),

using the Brunauer–Emmet–Teller (BET...densities were determined using a gas

pycnometer (Micrometrics AccuPyc 1330) working under a helium atmosphere.

Results are expressed...

New tannin–lignin aerogels

Grishechko, L.I. / Amaral-Labat, G. / Szczurek, A. /

Fierro, V. / Kuznetsov, B.N. / Pizzi, A. / Celzard,

A., Industrial Crops and Products, 41, p.347-355,

Jan 2013

..Envelope Density Analyser (Micromeritics, USA). The skeletal density...measured

by helium pycnometry (Accupyc II 1340, Micromeritics, USA) using finely crushed

samples for...automatic apparatus (ASAP 2020, Micromeritics, USA). The samples

were first...











http://www.hindawi.com/journals/jma/2013/287853/

http://www.hindawi.com/journals/jma/2013/287853/


















Nitramines with Varying Sensitivities:

Functionalized

Dipyrazolyl-N-nitromethanamines as

Energetic Materials

J Zhang, C He, DA Parrish… - Chemistry-A

European …, 2013 - Wiley Online Library

... Densities were measured at room temperature by using a Micromeritics AccuPyc

1330 gas pycnometer. Elemental analyses were carried out on an Exeter CE-440

elemental analyzer. The mass spectra were obtained by using a Shimadzu GCMS-

QP5050A mass spectrometer.

Novel flexible aerogels derived from

methyltrimeth...

Aravind, Parakkulam Ramaswamy / Niemeyer,

Philipp / Ratke, Lorenz, Microporous and

Mesoporous Materials, 181, p.111-115, Nov 2013

..was used to determine the skeletal density using Micromeritics AccuPyc II 1340

and the value was found to be 1.43 g/cm 3...adsorption at 77 K (using a Tristar II

3020, from Micromeritics, Norcross, USA). The specific surface area...

Novel flexible aerogels derived from

methyltrimeth...

Aravind, Parakkulam Ramaswamy / Niemeyer,

Philipp / Ratke, Lorenz, Microporous and

Mesoporous Materials, 181, p.111-115, Nov 2013

..used to determine the skeletal density using Micromeritics AccuPyc II 1340 and the

value was found to be 1...determined by N 2 adsorption at 77 K (using a Tristar II

3020, from Micromeritics, Norcross, USA). The specific surface area...

Novel polyvinyl alcohol nanocomposites

containing carbon nano-tubes with Fe 3 O 4

pendants for alkaline fuel cell applications

Lo, Chieh-Fang / Wu, Jung-Fen / Li, Hsieh-Yu /

Hung, Wei-Song / Shih, Chao-Ming / Hu, Chien-

Chieh / Liu, Ying-Ling / Lue, Shingjiang Jessie,

Journal of Membrane Science, 444, p.41-49, Oct

2013

..were determined using a gas pycnometer (AccuPyc II 1340, Micromeritics,

Norcross, GA, USA) using Archimedes's...which was measured using a gas

pycnometer, AccuPyc II 1340, Micromeritics, Norcross, GA, USA). V W is the van...

Novel processing of iron–manganese alloy-

based biomaterials by inkjet 3-D printing

Chou, Da-Tren / Wells, Derrick / Hong, Daeho /

Lee, Boeun / Kuhn, Howard / Kumta, Prashant N.,

Acta Biomaterialia, 9 (10), p.8593-8603, Nov 2013

..sintered 3-DP parts were measured using an AccuPyc II 1340 helium pycnometer

(Micromeritics, Norcross, GA). The envelope density...parts was measured using a

GeoPyc 1360 (Micromeritics). Using these density values, the percent...

On the influence of silica type on the

structural integrity of dense La 9.33 Si 2 Ge 4

O 26 electrolytes for SOFCs

Alves, C. / Marcelo, T. / Oliveira, F.A.C. / Alves,

L.C. / Mascarenhas, J. / Trindade, B., Journal of

the European Ceramic Society, 33 (12), p.2251-

2258, Oct 2013

..determined by laser scattering (Cilas 1064, France). True density measurements

were carried out using a AccuPyc 1330 Helium pycnometer (Micromeritics Int.

Corp., USA). Further data on the characterization of the raw materials as well as

experimental...

Paper-derived hydroxyapatite Stares, Steferson Luiz / Fredel, Márcio Celso /

Greil, Peter / Travitzky, Nahum, Ceramics

International, 39 (6), p.7179-7183, Aug 2013

..a digital dial indicator. Skeletal density ( ρ skeletal ) of the samples was measured

by He-Pycnometry (AccuPyc 1330, Micromeritics Instrument Corporation, Norcross,

GA, USA). Total porosity of the samples ( P p ) was derived from fractional...

Paper-derived β -TCP Stares, S.L. / Fredel, M.C. / Greil, P. / Travitzky,

N., Materials Letters, 98, p.161-163, May 2013

..a digital dial indicator. Skeletal density ( ρ skeletal ) of the samples was measured

by He-Pycnometry (AccuPyc 1330, Micromeritics Instrument Corporation, Norcross,

GA, USA). Total porosity of the samples ( P p ) was derived from fractional...

Performance of a bauxite waste as oxygen-

carrier for chemical-looping combustion

using coal as fuel

Mendiara, T. / Gayán, P. / Abad, A. / de Diego,

L.F. / García-Labiano, F. / Adánez, J., Fuel

Processing Technology, 109, p.57-69, May 2013

..measured by Hg intrusion in a Quantachrome PoreMaster 33. The real density of

the particles was measured with a Micromeritics AccuPyc II 1340 helium

picnometer. Brunauer–Emmett–Teller (BET) surface area value was measured and a

low value...

Performance of CLOU process in the

combustion of different types of coal with CO

2 capture

Adánez-Rubio, I. / Abad, A. / Gayán, P. / de

Diego, L.F. / García-Labiano, F. / Adánez, J.,

International Journal of Greenhouse Gas Control,

12, p.430-440, Jan 2013

..pores, was determined by He picnometry in a Micromeritics AccuPyc II 1340. The

surface area of the oxygen carrier...adsorption/desorption of nitrogen at 77 K in a

Micromeritics ASAP-2020 (Micromeritics Instruments Inc.), whereas the pore

volumes...

http://onlinelibrary.wiley.com/doi/10.1002/chem.201300747/abstract




http://en.wit.findplus.cn/?h=articles&db=edsgao&an=edsgcl.346064413





















Phosphorus flame retardant polybenzoxazine

foams based on renewable diphenolic acid

Zúñiga, Camilo / Larrechi, Maria Soledad /

Lligadas, Gerard / Ronda, Juan Carlos / Galià,

Marina / Cádiz, Virginia, Polymer Degradation

and Stability, In Press, Corrected Proof,Oct 2013

..P (161.9 MHz) NMR spectra were obtained using a Varian Gemini 400

spectrometer with Fourier transform and DMSO-d 6...The closed-cell volume

percentage was determined with a Micromeritics AccuPyc 1330 Gas Pycnometer

thermostatized at 40 °C, using...

Phosphorus flame retardant polybenzoxazine

foams based on renewable diphenolic acid

Zúñiga, Camilo / Larrechi, Maria Soledad /

Lligadas, Gerard / Ronda, Juan Carlos / Galià,

Marina / Cádiz, Virginia, Polymer Degradation

and Stability, In Press, Corrected Proof,Oct 2013

..least three measurements using different specimen. The closed-cell volume

percentage was determined with a Micromeritics AccuPyc 1330 Gas Pycnometer

thermostatized at 40 °C, using argon as gas according to a modification of ASTM

D6226-10...

Photovoltaic's silica-rich waste sludge as

supplementary cementitious material (SCM)

Quercia, G. / van der Putten, J.J.G. / Hüsken, G. /

Brouwers, H.J.H., Cement and Concrete

Research, 54, p.161-179, Dec 2013

..physical adsorption isotherm (BET method) A Micromeritics TriStar 3000

equipment using N 2 with a soaking...density by helium pycnometry A helium

pycnometer AccuPyc® II 1340 from Micromeritics was used to determine the

specific density of...

Photovoltaic's silica-rich waste sludge as

supplementary cementitious material (SCM)

Quercia, G. / van der Putten, J.J.G. / Hüsken, G. /

Brouwers, H.J.H., Cement and Concrete

Research, 54, p.161-179, Dec 2013

..Nitrogen physical adsorption isotherm (BET method) A Micromeritics TriStar 3000

equipment using N 2 with a soaking time of 12...pycnometry A helium pycnometer

AccuPyc® II 1340 from Micromeritics was used to determine the specific density of

the...

Physical characterization of sweet sorghum

bagasse, tobacco residue, soy hull and fiber

sorghum bagasse particles: Density, particle

size and shape distributions

Cardoso, C.R. / Oliveira, T.J.P. / Santana Junior,

J.A. / Ataíde, C.H., Powder Technology, 245,

p.105-114, Sep 2013

..five analyses for each biomass. 2.4 True density A Micromeritics AccuPyc 1331 gas

pycnometer with a measuring sensitivity of...ranges of the same material due to the

equipment (AccuPyc 1331) precision. The objective of these measurements...

Physical property behaviour of North Dakota

lignite in an oxygen/steam blown moving bed

gasifier

Mangena, S.J. / Bunt, J.R. / Waanders, F.B., Fuel

Processing Technology, 106, p.326-331, Feb 2013

..was of an approximately 10 g sample was determined for the gasifier turn-out

samples (crushed to below 1 mm), using a Micromeretics Accupyc instrument. The

crushed samples were dried overnight in an oven at 105 °C and then cooled in a

desiccator prior...

Poly-lactide- co -glycolide nanoparticles

containing voriconazole for pulmonary

delivery: in vitro and in vivo study

Sinha, Biswadip / Mukherjee, Biswajit / Pattnaik,

Gurudutta, Nanomedicine: Nanotechnology,

Biology and Medicine, 9 (1), p.94-104, Jan 2013

..mercury porosimeter (AutoPore IV 9500; Micromeritics Instruments, Norcross,

USA) at the lowest...density of the particles was measured using an AccuPyc 1340

helium pycnometer (Micromeritics Instruments) with a 1-mL sample chamber...

Poly-lactide- co -glycolide nanoparticles

containing voriconazole for pulmonary

delivery: in vitro and in vivo study

Sinha, Biswadip / Mukherjee, Biswajit / Pattnaik,

Gurudutta, Nanomedicine: Nanotechnology,

Biology and Medicine, 9 (1), p.94-104, Jan 2013

..was determined using a mercury porosimeter (AutoPore IV 9500; Micromeritics

Instruments, Norcross, USA) at the lowest...measured using an AccuPyc 1340

helium pycnometer (Micromeritics Instruments) with a 1-mL sample chamber

using...

Porcelain containing anatase and rutile

nanocrystals

Bouzidi, N. / Bouzidi, A. / Gaudon, P. / Merabet,

D. / Blanchart, P., Ceramics International, 39 (1),

p.489-495, Jan 2013

..were achieved by the Archimedes's method in water, and absolute densities were

measured by helium pycnometry (Micromeritics AccuPyc). Bulk and absolute

densities were used to calculate the total porosity of samples. The dielectric

properties...

Porous materials for alkali contaminated

environments

Brachhold, Nora / Aneziris, Christos G., Journal of

the European Ceramic Society, 33 (10), p.2013-

2021, Sep 2013

..volumeter. Total porosity was calculated from the true density of the material

measured by He-pycnometer AccuPyc 1330 (Micromeritics, Aachen, Germany).

Refractoriness under load was determined according to DIN EN ISO 1893 in a

NETZSCH hood...





http://www.tue.nl/en/publication/ep/p/d/ep-uid/287184/














http://www.nanomedjournal.com/article/S1549-9634%2812%2900178-5/abstract








Predicting the density and tensile strength of

viscoelastic soy powder compacts Pai, Dhananjay A. / Okos, Martin R., Journal of

Food Engineering, 116 (1), p.184-194, May 2013

..based on volume after pouring and at the end of tapping respectively. 5. True

density: Nitrogen Pycnometer (Accupyc 1330, Micromeritics, GA) ( n = 20 for Soy

Flour, n = 10 for Soy Protein Concentrate) ( Fitzpatrick et al. 2004 ). 2.2...

Preparation and characterization of low-

crystallized hydroxyapatite nanoporous

plates and granules

Uehira, Mayo / Okada, Masahiro / Takeda, Shoji /

Matsumoto, Naoyuki, Applied Surface Science, In

Press, Corrected Proof,Sep 2013

..mercury intrusion porosimetry (AutoPore IV 9520; Micromeritics Instrument Corp.,

Norcross, GA), after the...samples were determined using helium pycnometry

(AccuPyc 1330; Micromeritics Instrument Corp., Norcross, GA), after the...

Preparation and characterization of low-

crystallized hydroxyapatite nanoporous

plates and granules

Uehira, Mayo / Okada, Masahiro / Takeda, Shoji /

Matsumoto, Naoyuki, Applied Surface Science, In

Press, Corrected Proof,Sep 2013

..determined using mercury intrusion porosimetry (AutoPore IV 9520; Micromeritics

Instrument Corp., Norcross, GA), after the...determined using helium pycnometry

(AccuPyc 1330; Micromeritics Instrument Corp., Norcross, GA), after the...

Preparation and characterization of olive pits

powder as a filler to PLA-matrix Bio-

composites

Koutsomitopoulou, A.F. / Bénézet, J.C. / Bergeret,

A. / Papanicolaou, G.C., Powder Technology, In

Press, Accepted Manuscript,Nov 2013

..absolute density is determined by measuring the helium pressure change in a

calibrated volume (He Pycnometer, AccuPyc 1330 Micromeritics). The bulk density

for porous materials is defined as the density measured by considering the overall

volume...

Preparation and characterization of TiO 2

doped and MgO stabilized Na–β″-Al 2 O 3

electrolyte via a citrate sol–gel method

Shan, Shi-Jie / Yang, Li-Ping / Liu, Xiao-Min / Wei,

Xiao-Ling / Yang, Hui / Shen, Xiao-Dong, Journal

of Alloys and Compounds, 563, p.176-179, Jun

2013

..respectively. The density of the sintered samples was measured using an absolute

type analysis technique with a micromeritics Accupyc II1340 Pycnometer under 20

psi of Nitrogen. The relative density was calculated as the following equation: (3...

Preparation of high refractive index La 2 O 3 -

TiO 2 glass by aerodynamic levitation

technique and effects of Bi 2 O 3 substitution

on its thermal and optical properties

Xiang, Heng / Guan, Lu / Peng, Zhijian / Li,

Jianqiang, Ceramics International, In Press,

Accepted Manuscript,Oct 2013

..x-ray fluorescence spectrometer (PANalytical, Axios mAX ). The sample density was

measured by a gas pycnometer (Micromeritics Accupyc II 1340). The glass transition

temperature T g and crystallization onset temperature T x of the prepared glasses...

Preparation of the carbon sphere coated with

iron oxide and its application for electronic

paper

Lee, Kang Uk / Park, Kyung Ju / Kim, Myeong Ho /

Kwon, Oh Joong / Kim, Jae Jeong, Dyes and

Pigments, In Press, Accepted Manuscript,Oct

2013

..clip. 2.7 Characterization of the pigment The density of particles was measured

using gas pycnometry (AccuPyc Ⅱ1340, MICROMERITICS). The surface charge of

pigments was investigated by adopting a zeta potential analyzer (ELS-Z2plus...

Preparation, characterisation and dissolution

of a CeO 2 analogue for UO 2 nuclear fuel

Stennett, Martin C. / Corkhill, Claire L. / Marshall,

Luke A. / Hyatt, Neil C., Journal of Nuclear

Materials, 432 (1-3), p.182-188, Jan 2013

..characterisation Powder densities were measured using a Micromeritics AccuPyc II

1340 pycnometer. The pycnometer was purged 50...Surface area analysis by BET

was conducted using a Micromeritics Gemini 2360 instrument. The powder was

flushed...

Preparation, characterisation and dissolution

of a CeO 2 analogue for UO 2 nuclear fuel

Stennett, Martin C. / Corkhill, Claire L. / Marshall,

Luke A. / Hyatt, Neil C., Journal of Nuclear

Materials, 432 (1-3), p.182-188, Jan 2013

..characterisation Powder densities were measured using a Micromeritics AccuPyc II

1340 pycnometer. The pycnometer was purged...Surface area analysis by BET was

conducted using a Micromeritics Gemini 2360 instrument. The powder was flushed

with nitrogen...

Production of nepheline/quartz ceramics

from geopolymer mortars

Kuenzel, C. / Grover, L.M. / Vandeperre, L. /

Boccaccini, A.R. / Cheeseman, C.R., Journal of the

European Ceramic Society, 33 (2), p.251-258, Feb

2013

..Archimedes’ principle, 31 with the theoretical density determined on milled

samples using pycnometry (AccuPyc II 1340 He pycnometer, Micromeritics, GA,

USA). 2.4 Physical property characterisation Vickers hardness was determined on

polished...















http://jglobal.jst.go.jp/public/20090422/201402229551855146














Production of polyphenol extracts from grape

bagasse using supercritical fluids: Yield,

extract composition and economic evaluation

Farías-Campomanes, Angela M. / Rostagno,

Mauricio A. / Meireles, M. Angela A., The Journal

of Supercritical Fluids, 77, p.70-78, May 2013

..changes were observed. The true density ( ρ t ) of the particles was determined by

picnometry with helium gas (Micromeritics, model AccuPyc II 1340 V1.02, Norcross,

USA). The bed apparent density ( ρ a ) was calculated by dividing the feed...

Properties of graphite composites based on

natural and synthetic graphite powders and a

phenolic novolac binder

Magampa, P.P. / Manyala, N. / Focke, W.W.,

Journal of Nuclear Materials, 436 (1-3), p.76-83,

May 2013

..Geopyc 1360 pycnometer. The helium density was measured with Accupyc II 1340

V1.03 Helium pycnometer. The volume of the...calculating helium density. Both

pycnometers were purchased from Micromeritics Instruments Corporation, USA.

The open accessible porosity...

Pyrolysis of blends of coal and tyre wastes in

a fixed bed reactor and a rotary oven Acevedo, B. / Barriocanal, C. / Alvarez, R., Fuel,

113, p.817-825, Nov 2013

..means of helium pycnometry in a Micromeritics Accupyc 1330 Pycnometer. Their

apparent...with mercury at 0.1 MPa in a Micromeritics Autopore IV 9500 mercury

porosimeter...N 2 adsorption at 77 K on a Micromeritics ASAP 2420 apparatus. The

software...



113, p.817-825, Nov 2013

..of helium pycnometry in a Micromeritics Accupyc 1330 Pycnometer.

Their...mercury at 0.1 MPa in a Micromeritics Autopore IV 9500 mercury

porosimeter...2 adsorption at 77 K on a Micromeritics ASAP 2420 apparatus. The

software package...



113, p.817-825, Nov 2013

..of helium pycnometry in a Micromeritics Accupyc 1330 Pycnometer.

Their...mercury at 0.1 MPa in a Micromeritics Autopore IV 9500 mercury

porosimeter. From...2 adsorption at 77 K on a Micromeritics ASAP 2420 apparatus.

The...

Rapid synthesis of La 0.85 Na 0.15 MnO 3 by

spark plasma sintering: Magnetic behavior

and magnetocaloric properties

Regaieg, Y. / Sicard, L. / Monnier, J. / Delaizir, G. /

Koubaa, M. / Godart, C. / Ammar-Merah, S. /

Cheikhrouhou, A., Materials Chemistry and

Physics, 139 (2-3), p.629-633, May 2013

..Supra40 ZEISS FEG-SEM microscope operating at 10 kV. The density of the as-

produced pellets was measured with a Micromeritics AccuPyc 1330 helium

pycnometer. Quantitative analysis of chemical elements was performed by

inductively coupled plasma...

Rheo-SAXS investigation of organoclay water

in oil emulsions

Akkal, R. / Cohaut, N. / Khodja, M. / Ahmed-Zaid,

T. / Bergaya, F., Colloids and Surfaces A:

Physicochemical and Engineering Aspects, 436,

p.751-762, Sep 2013

..VG69 ® , and Geltone ® ) are used in this work. Their density ( ρ ) is measured up by

Helium pycnometry (Accupyc 1330, Micromeritics). Bentone 38 (Elementis) is an

organically modified hectorite ( ρ = 1.66 g/cm 3 ) obtained from a...

Sago starch as binder and pore-forming agent

for the fabrication of porcelain foam

Jamaludin, Abdul Rashid / Kasim, Shah Rizal /

Abdullah, Mohd Zukifly / Ahmad, Zainal Arifin,

Ceramics International, In Press, Corrected

Proof,Sep 2013

..the medium for relative comparison and ρ th is attained from the density test

measured with a gas pycnometer (Micromeritics AccuPyc 1330). m 1 is the dried

weight of the sample, whereas m 2 and m 3 are the weight of the sample measured

after...

Sintering and crystallization of plates

prepared from coarse glass ceramic frits

Piva, Jorge Henrique / Wanderlind, Augusto /

Just, Jeanini / Montedo, Oscar Rubem Klegues /

De Noni, Agenor, Junior, Ceramics International,

39 (8), p.9137-9144, Dec 2013

..densities of specimen powders, obtained by dry grinding in a tungsten carbide mill,

were measured by He picnometry (Micromeritics Accupyc 1340, Norcross, USA),

while crystalline phases were determined by X-ray diffractometry (Shimadzu XRD-

6000...

Soil property effects on wind erosion of

organic soils

Zobeck, Ted M. / Baddock, Matthew / Scott Van

Pelt, R. / Tatarko, John / Acosta-Martinez,

Veronica, Aeolian Research, 10, p.43-51, Sep 2013

..in each sample interval using the particle density measured for each site

determined with a Micromeritics AccuPyc 1330 helium pycnometer (Micromeritics

Instrument Corp., Norcross, GA, USA) from sieved bulk samples as described in the

next...













https://www.infona.pl/resource/bwmeta1.element.elsevier-f2c5b74f-1d40-3342-b6ab-745fe0afb9e3












Solid crystal suspensions containing

griseofulvin – Preparation and bioavailability

testing

Reitz, Elena / Vervaet, Chris / Neubert, Reinhard

H.H. / Thommes, Markus, European Journal of

Pharmaceutics and Biopharmaceutics, 83 (2),

p.193-202, Feb 2013

..true density ( ρ true ) of the extrudate was determined in a 3.5 ml sample holder

with a helium pycnometer (AccuPyc, Micromeritics, Moenchengladbach, Germany).

The apparent density ( ρ app ) was characterized by a mercury porosimeter...

Solid lipid particles in lipid films to control the

diffusive release of 2-heptanoneC Bilbao-Sáinz, BS Chiou, GM Glenn… - Pest

management …, 2013 - Wiley Online Library

... was monitored for the different particles using thermogravimetric analysis

(Model 2950; TA Instruments ... films and the composite SLP films was performed in

a TA Instruments DSC 2910. ... using a gas pycnometer (AccuPyc II 1340 Series

pycnometer; Micromeritics Instrument Co

Solution-based approaches for making high-

density sodalite waste forms to immobilize

spent electrochemical salts

Lepry, William C. / Riley, Brian J. / Crum, Jarrod V.

/ Rodriguez, Carmen P. / Pierce, David A., Journal

of Nuclear Materials, 442 (1-3), p.350-359, Nov

2013

..mp ), and the average pore size. Helium pycnometry was used to measure

specimen density ( ρ s ) with an AccuPyc II 1340 (Micromeritics Instrument

Corporation, Norcross, GA). 2.7 Product consistency test (PCT) Specimens of

SM1–5...

Spheronisation mechanism of MCC II-based

pellets

Krueger, Cornelia / Thommes, Markus /

Kleinebudde, Peter, Powder Technology, 238,

p.176-187, Apr 2013

..acceptable. 2.2.6 Porosity The helium density (ρ He ) of the pellets was determined

by a helium pycnometer (AccuPyc, Micromeritics, Moenchengladbach, Germany).

For each tested pellet batch three samples were analyzed. The apparent density...

Stabilization of fluorine-containing industrial

waste by production of sintered glass-

ceramics

Ponsot, Inès / Falcone, Roberto / Bernardo,

Enrico, Ceramics International, 39 (6), p.6907-

6915, Aug 2013

..materials was estimated by means of the Archimedes principle, whereas the true

density was assessed by He pycnometry (Micromeritics AccuPyc 1330, Norcross,

GA). The main crystalline phases of all heat-treated samples and untreated ground

mixtures...

Structural changes to resorbable calcium

phosphate bioceramic aged in vitro

Mehrban, Nazia / Bowen, James / Vorndran, Elke

/ Gbureck, Uwe / Grover, Liam M., Colloids and

Surfaces B: Biointerfaces, 111, p.469-478, Nov

2013

..densities were determined using a helium pycnometer (AccuPyc II 1340,

Micromeritics, UK) employing 100 measurements per sample with...analysed using

an AutoPore IV mercury porosimeter (Micromeritics, UK) at pressures in the range 3

kPa–207...

Structural changes to resorbable calcium

phosphate bioceramic aged in vitro

Mehrban, Nazia / Bowen, James / Vorndran, Elke

/ Gbureck, Uwe / Grover, Liam M., Colloids and

Surfaces B: Biointerfaces, 111, p.469-478, Nov

2013

..using a helium pycnometer (AccuPyc II 1340, Micromeritics, UK) employing 100

measurements per sample...was sealed and the sample analysed using an AutoPore

IV mercury porosimeter (Micromeritics, UK) at pressures in the range 3 kPa...

Structure and oxidation resistance of micro-

cellular Si–SiC foams derived from natural

resins

Amaral-Labat, G. / Zollfrank, C. / Ortona, A. /

Pusterla, S. / Pizzi, A. / Fierro, V. / Celzard, A.,


2013

..ρ s was measured by helium pycnometry (Accupyc II 1340, Micromeritics, USA).

For that purpose, sample pieces were crushed in a mortar...size distribution was

estimated by mercury porosimetry (AutoPore IV 9500, Micrometrics, USA). The

experiments were performed...

Structure and oxidation resistance of micro-

cellular Si–SiC foams derived from natural

resins

Amaral-Labat, G. / Zollfrank, C. / Ortona, A. /

Pusterla, S. / Pizzi, A. / Fierro, V. / Celzard, A.,


2013

..known dimensions (3×3×1.5 cm 3 ). The skeletal density ρ s was measured by

helium pycnometry (Accupyc II 1340, Micromeritics, USA). For that purpose, sample

pieces were crushed in a mortar and dried at 120 °C in vacuum overnight...

Studies on the lithium ion diffusion

coefficients of electrospun Nb 2 O 5

nanostructures using galvanostatic

intermittent titration and electrochemical

impedance spectroscopy

Reddy, M.V. / Jose, R. / Le Viet, A. / Ozoemena,

Kenneth I. / Chowdari, B.V.R. / Ramakrishna, S.,

Electrochimica Acta, In Press, Corrected

Proof,Oct 2013

..TOPAS software. Density measurement was performed using pycnometer

(AccuPyc 1330, Micromeritics) and BET surface area was evaluated by a surface area

analyzer (Micromeritics Tristar 3000). Electrodes for the Li-diffusion coefficient

studies...






























Studies on the lithium ion diffusion

coefficients of electrospun Nb 2 O 5

nanostructures using galvanostatic

intermittent titration and electrochemical

impedance spectroscopy

Reddy, M.V. / Jose, R. / Le Viet, A. / Ozoemena,

Kenneth I. / Chowdari, B.V.R. / Ramakrishna, S.,

Electrochimica Acta, In Press, Corrected

Proof,Oct 2013

..Density measurement was performed using pycnometer (AccuPyc 1330,

Micromeritics) and BET surface area was evaluated by a surface area analyzer

(Micromeritics Tristar 3000). Electrodes for the Li-diffusion coefficient studies were

prepared...

Supercritical carbonation of calcareous

composites: Influence of curing

Farahi, Elham / Purnell, Phil / Short, Neil R.,

Cement and Concrete Composites, 43, p.48-53,

Oct 2013

..measured by micrometer and weighed, providing the bulk density. They were then

tested in a helium pycnometer (AccuPyc 1330, Micromeritics) over 10 purge cycles

to provide the true densities, from which the porosity was calculated. Samples

were...

Supercritical carbonation of calcareous

composites: Influence of mix design

Farahi, Elham / Purnell, Phil / Short, Neil R.,

Cement and Concrete Composites, 43, p.12-19,

Oct 2013

..measured using a micrometer and the bulk density calculated. They were then

tested in a helium pycnometer (AccuPyc 1330, Micromeritics) over 10 purge cycles

to provide the true densities, from which the porosity was calculated. For each

case...

Superparamagnetic iron oxide nanoparticles

(SPIONs)-loaded Trojan microparticles for

targeted aerosol delivery to the lung

Tewes, Frederic / Ehrhardt, Carsten / Healy, Anne

Marie, European Journal of Pharmaceutics and

Biopharmaceutics, In Press, Corrected Proof,Sep

2013

..properties ( n = 2). 2.2.5 Particle true density The true density of the materials was

measured using an Accupyc 1330 Pycnometer (Micromeritics®) with helium

(99.995% purity) to determine the volume of accurately weighed samples. Samples...

Syndiotactic polystyrene aerogels containing

multi-walled carbon nanotubes Wang, Xiao / Jana, Sadhan C., Polymer, 54 (2),

p.750-759, Jan 2013

..specimens. The skeletal density ρ s was measured using an Accupyc 1340 Helium

Pycnometer (Micrometrics Instrument Corp...nitrogen adsorption–desorption

isotherms analyzed using Micromeritics Tristar II 3020 Analyzer. The aerogel

specimens were sectioned...

Synthesis and Characterization of Urea

Nitrate and NitroureaJC Oxley, JL Smith, S Vadlamannati… -

Propellants, …, 2013 - Wiley Online Library

... 2.2 Densities, Solubility and Melting Points of UN and NU. Ten density

determinations for UN and NU products were obtained using a Micromeritics

AccuPyc 1340 gas pycnometer. ... Ammonium nitrate exhibited additional small

peak at ca. 2900 cm −1 .

Synthetic Methods for Preparing Ionic Liquids

Containing Hypophosphite and

Carbon-Extended Dicyanamide Anions

JP Maciejewski, H Gao… - Chemistry-A European

…, 2013 - Wiley Online Library

... Chem. Eur. J., 19: 2947–2950. doi: 10.1002/chem.201203740. Author

Information. 1 ... Densities were measured by using a Micromeritics Accupyc 1330

gas pycnometer. Viscosities were measured with a Grabner MINIVIS II Portable

Micro viscometer.

Tannin-based xerogels with distinctive

porous structures

Amaral-Labat, G. / Grishechko, L.I. / Fierro, V. /

Kuznetsov, B.N. / Pizzi, A. / Celzard, A., Biomass

and Bioenergy, 56, p.437-445, Sep 2013

..pycnometry (Accupyc II 1340, Micromeritics, USA). For that purpose,

samples...automatic adsorption apparatus (Micromeritics, USA). For that

purpose...porosimetry experiments (AutoPore IV 9500, Micromeritics) were carried

out. This...

Tannin-based xerogels with distinctive

porous structures

Amaral-Labat, G. / Grishechko, L.I. / Fierro, V. /

Kuznetsov, B.N. / Pizzi, A. / Celzard, A., Biomass

and Bioenergy, 56, p.437-445, Sep 2013

..Envelope Density Analyser (Micromeritics, USA). The skeletal density...measured

by helium pycnometry (Accupyc II 1340, Micromeritics, USA). For that purpose,

samples...automatic adsorption apparatus (Micromeritics, USA). For that purpose...















http://onlinelibrary.wiley.com/doi/10.1002/prep.201200178/abstract

http://onlinelibrary.wiley.com/doi/10.1002/prep.201200178/abstract









The degree of compression of spherical

granular solids controls the evolution of

microstructure and bond probability during

compaction

Nordström, Josefina / Persson, Ann-Sofie /

Lazorova, Lucia / Frenning, Göran / Alderborn,

Göran, International Journal of Pharmaceutics,

442 (1-2), p.3-12, Feb 2013

..determined by helium displacement using a pycnometer (AccuPyc 1330,

Micromeritics, USA). Two powder samples were taken and each...measurements in

a porosimeter (Autopore III 9420, Micromeritics, USA). An amount of pellets in the

range 900...

The degree of compression of spherical

granular solids controls the evolution of

microstructure and bond probability during

compaction

Nordström, Josefina / Persson, Ann-Sofie /

Lazorova, Lucia / Frenning, Göran / Alderborn,

Göran, International Journal of Pharmaceutics,

442 (1-2), p.3-12, Feb 2013

..displacement using a pycnometer (AccuPyc 1330, Micromeritics, USA). Two

powder samples were taken and each...mercury intrusion measurements in a

porosimeter (Autopore III 9420, Micromeritics, USA). An amount of pellets in the

range...

The effect of concentration on the structure

and crystallinity of a cementitious waste

form for caustic wastes

Chung, Chul-Woo / Turo, Laura A. / Ryan, Joseph

V. / Johnson, Bradley R. / McCloy, John S., Journal

of Nuclear Materials, 437 (1-3), p.332-340, Jun

2013

..used for helium pycnometry utilizing an AccuPyc II 1340 Gas Pycnometer from

Micrometrics...intrusion porosimetry (MIP) was performed by Micromeritics on the

Cast Stone specimens using a Micromeritics AutoPore 9520 instrument capable of

pressures...

The improvement of electron transport rate

of TiO 2 dye-sensitized solar cells using mixed

nanostructures with different phase

compositions

Bakhshayesh, A.M. / Mohammadi, M.R.,

Ceramics International, 39 (7), p.7343-7353, Sep

2013

..density of TiO 2 nanostructures was measured by a Micromeritics AccuPyc 1330

pycnometer analyzer. They were also characterized...equations, respectively at

77.35 K using a Micromeritics Tristar 3000 analyzer. External surface area of...

The improvement of electron transport rate

of TiO 2 dye-sensitized solar cells using mixed

nanostructures with different phase

compositions

Bakhshayesh, A.M. / Mohammadi, M.R.,

Ceramics International, 39 (7), p.7343-7353, Sep

2013

..density of TiO 2 nanostructures was measured by a Micromeritics AccuPyc 1330

pycnometer analyzer. They were also characterized...equations, respectively at

77.35 K using a Micromeritics Tristar 3000 analyzer. External surface area of the

samples...

The influence of rolling friction on the shear

behaviour of non-cohesive pharmaceutical

granules – An experimental and numerical

investigation

Persson, Ann-Sofie / Frenning, Göran, European

Journal of Pharmaceutical Sciences, 49 (2), p.241-

250, May 2013

..cm 3 ) was measured with helium pycnometry (AccuPyc 1330, Micromeritics, USA).

The granules were stored at...from mercury pycnometry (Autopore III 9420,

Micromeritics, USA) as described by Wikberg and Alderborn...

The influence of rolling friction on the shear

behaviour of non-cohesive pharmaceutical

granules – An experimental and numerical

investigation

Persson, Ann-Sofie / Frenning, Göran, European

Journal of Pharmaceutical Sciences, 49 (2), p.241-

250, May 2013

..measured with helium pycnometry (AccuPyc 1330, Micromeritics, USA). The

granules were stored at...2) was assessed from mercury pycnometry (Autopore III

9420, Micromeritics, USA) as described by Wikberg and Alderborn...

The influence of SrSO 4 on the tribological

properties of NiCr–Al 2 O 3 cermet at

elevated temperatures

Liu, Feng / Yi, Gewen / Wang, Wenzhen / Shan,

Yu / Jia, Junhong, Ceramics International, In

Press, Corrected Proof,Oct 2013

..following analyses and tests. The density of the sintered composites was

determined by using a helium pycnometry (AccuPyc 1330, Micromeritics Int. Corp.,

USA) after calculating the volume. The hardness measurements were conducted

using MH–5...




























http://www.researchgate.net/publication/259513019_The_influence_of_SrSO4_on_the_tribological_properties_of_NiCrAl2O3_cermet_at_elevated_temperatures




The kinetics of devitrification of amorphous

alloys: The time–temperature–crystallinity

diagram describing the spark plasma

sintering of Fe-based metallic glasses

Graeve, O.A. / Saterlie, M.S. / Kanakala, R. / de la

Torre, S. Diaz / Farmer, J.C., Scripta Materialia, 69

(2), p.143-148, Jul 2013

..surfaces of the sintered specimens. The density of the powders and sintered

specimens was determined using a Micromeritics AccuPyc II 1340 ultrahigh-purity

He pycnometer. 3 Results and discussion The morphology of the sintered specimens

is...

The morphology of limestone-based pellets

prepared with kaolin-based binders

Ridha, Firas N. / Manovic, Vasilije / Anthony,

Edward J. / Macchi, Arturo, Materials Chemistry

and Physics, 138 (1), p.78-85, Feb 2013

..pore size distribution were determined on a Micromeritics analyzer (Micromeritics

Tristar II-3020) by N 2 adsorption at...was determined using helium pycnometry

(Micromeritics AccuPyc II-1340 Pycnometer). Scanning electron...

The use of egg shells to produce Cathode Ray

Tube (CRT) glass foams

Fernandes, Hugo R. / Andreola, Fernanda /

Barbieri, Luisa / Lancellotti, Isabella / Pascual,

Maria J. / Ferreira, José M.F., Ceramics

International, 39 (8), p.9071-9078, Dec 2013

..following characterization techniques were employed: (1) the absolute density was

measured using a He pycnometer (Micromeritics Accupyc 1330, USA); (2) the

apparent density of materials was determined by measuring the weight and the

dimensions...

Thermal stability and water effect on ion-

exchange resins in ethyl octyl ether

production at high temperature

Guilera, Jordi / Ramírez, Eliana / Fité, Carles /

Iborra, Montserrat / Tejero, Javier, Applied

Catalysis A: General, 467, p.301-309, Oct 2013

..to approach the industrial reactor. Skeletal density ( ρ s ) was measured by helium

displacement in an Accupyc 1330 apparatus (Micromeritics). BET surface area, S BET

, was estimated from N 2 adsorption-desorption isotherm at 77 K (krypton...

Thermoelectric Ca 0.9 Yb 0.1 MnO 3− δ grain

growth controlled by spark plasma sintering

Quetel-Weben, Simon / Retoux, Richard /

Noudem, Jacques G., Journal of the European

Ceramic Society, 33 (10), p.1755-1762, Sep 2013

..Archimedes method with a Kern ABT 220–4 M analytical balance and checked by

the helium pycnometry process with a Micromeritics AccuPyc 1330 pycnometer. X-

ray powder diffraction patterns were recorded on an X’PERT (Almelo, Netherlands...

Three-dimensional printing of SiSiC lattice

truss structures

Fu, Z. / Schlier, L. / Travitzky, N. / Greil, P.,

Materials Science and Engineering: A, 560, p.851-

856, Jan 2013

..composed of approximately 42 wt% of carbon. The density of the preforms was

determined via helium pycnometry (Accupyc 1330, Micromeretics, Norcross, USA)

and open porosity of the preforms was calculated from the measured geometrical

and pycnometrical densities...

Transmission electron microscopy study of

the reaction mechanisms involved in the

carbothermal reduction of anatase

David, J. / Trolliard, G. / Maître, A., Acta

Materialia, 61 (14), p.5414-5428, Aug 2013

..measurements were performed with a helium picnometer (AccuPyc II 1340,

Micromeritics, Verneuil, France). The specific areas of the...Emmett–Teller (BET)

method (ASAP 2000, Micromeritics, Verneuil, France), and the size of particles...

Twin screw wet granulation: Influence of

formulation parameters on granule

properties and growth behavior

El Hagrasy, A.S. / Hennenkamp, J.R. / Burke, M.D.

/ Cartwright, J.J. / Litster, J.D., Powder

Technology, 238, p.108-115, Apr 2013

..granules was measured by a helium pycnometer (AccuPyc II 1340, Micromeritics,

Norcross, GA), using granules in the size...same size fraction was measured using

Geopyc (Micromeritics, Norcross, GA). In this method, a small...

Ultrahigh-pressure consolidation and

deformation of tantalum carbide at ambient

and high temperatures

Lahiri, Debrupa / Singh, Virendra / Rodrigues,

Giovani Ritta / Costa, Tania Maria Haas / Gallas,

Marcia R. / Bakshi, Srinivasa Rao / Seal, Sudipta /

Agarwal, Arvind, Acta Materialia, 61 (11), p.4001-

4009, Jun 2013

..TaC-RT and TaC-HT, respectively. The density of the pellets was measured using

helium gas pycnometry (Accupyc 1340, Micromeretics Instrument Corporation,

Norcross, GA, USA) and expressed in terms of relative density considering the true

density of...


























Understanding the key parameters for the

rational design of layered oxide materials by

composite sol–gel procedures

Ould-Chikh, S. / Brodusch, N. / Crozet, N. /

Hemati, M. / Rouleau, L., Powder Technology,

237, p.255-265, Mar 2013

..mercury porosimetry (Autopore 4-Micromeretics). Incertitude on porous volume

is...physisorption isotherms (ASAP 2420-Micromeretics). Skeletal densities of

powders are...measured by helium pycnometry (Accupyc-Micromeretics). Powder

bulk density and grain density...

Uniaxial tension and compression

characterization of hybrid CNS–glass

fiber–epoxy composites

Markkula, Sam / Malecki, H.C. / Zupan, Marc,

Composite Structures, 95, p.337-345, Jan 2013

..density and weight percent of fiber in the composite. The density of each

composite panel was measured with a Micromeritics AccuPyc gas pycnometer for

the purpose of comparing specific properties. The weight percent of fiber in each

glass...

Use of chemically and physically mixed iron

and nickel oxides as oxygen carriers for gas

combustion in a CLC process

Pans, Miguel A. / Gayán, Pilar / Abad, Alberto /

García-Labiano, Francisco / de Diego, Luis F. /

Adánez, Juan, Fuel Processing Technology, 115,

p.152-163, Nov 2013

..density of the particles was measured with a Micromeritics AccuPyc II 1340 helium

pycnometer. The surface area...adsorption/desorption of nitrogen at 77 K in a

Micromeritics ASAP-2020 (Micromeritics Instruments Inc.), whereas the pore

volume...

Use of different supports for oil

encapsulation in powder by spray drying

Turchiuli, C. / Jimenez Munguia, M.T. /

Hernandez Sanchez, M. / Cortes Ferre, H. /

Dumoulin, E., Powder Technology, In Press,

Corrected Proof,Aug 2013

..0.2 mm) (Density tester, Varian, Fr). The solid true density was measured using an

air pycnometer (AccuPyc, Micromeritics, Fr). The determination of the total oil

content of the powder required first the reconstitution of the liquid...

Use of silica nanopowder to accelerate CO 2

sorption by Ca(OH) 2 Quintanilla, M.A.S. / Valverde, J.M., Particuology,

11 (4), p.448-453, Aug 2013

..Particle density, determined by an AccuPyc 1330 Pycnometer (Quantachrome

Instruments...the BET surface area, determined by a Micromeritics Tristar II 3020

physisorption analyzer...manual gas pycnometer (Quantachrome AccuPyc 1330

Pycnometer) consisting of two vessels...

Use of silica nanopowder to accelerate CO 2

sorption by Ca(OH) 2 Quintanilla, M.A.S. / Valverde, J.M., Particuology,

11 (4), p.448-453, Aug 2013

..AccuPyc 1330 Pycnometer (Quantachrome Instruments), is 2.36 g/cm 3 and the

BET surface area, determined by a Micromeritics Tristar II 3020 physisorption

analyzer, is 16.32 m 2 /g. Scanning electron microscope (SEM) pictures of this

powder...

Wound dressings loaded with an anti-

inflammatory jucá ( Libidibia ferrea ) extract

using supercritical carbon dioxide technology

Dias, A.M.A. / Rey-Rico, A. / Oliveira, R.A. /

Marceneiro, S. / Alvarez-Lorenzo, C. / Concheiro,

A. / Júnior, R.N.C. / (...) / de Sousa, H.C., The

Journal of Supercritical Fluids, 74, p.34-45, Feb

2013

..dressing material), and ρ solid (g/cm 3 ) is the true density measured by helium

pycnometry (Accupyc 1330 Micromeritics, Micromeritics Instrument Corporation,

USA). 2.6 Fluid handling properties 2.6.1 Oxygen permeability Oxygen...




http://www.researchgate.net/publication/257095175_Uniaxial_tension_and_compression_characterization_of_hybrid_CNSglass_fiberepoxy_composites















Date post:	28-Mar-2018
Category:	Documents
Upload:	vudien
View:	213 times
Download:	1 times

AccuPyc Bibliography of Peer-Reviewed Papers · PDF fileAccuPyc Bibliography of Peer-Reviewed...

Documents