Date post: | 18-Oct-2015 |
Category: |
Documents |
Upload: | imthiyas-ahmed |
View: | 258 times |
Download: | 0 times |
5/27/2018 Acer x1130p, x1130pa, x1230pk,x1230p,x1230pa,x1237 Projectors Sm
1/109
Projector Service Manual
Model : X1130P, X1130PA, X1230PK,X1230P,X1230PA, X1237
Version: Rev3
First Edition (Jul. 2009)
RESTRICTIONS ON USE OF MATERIALS:
5/27/2018 Acer x1130p, x1130pa, x1230pk,x1230p,x1230pa,x1237 Projectors Sm
2/109
Index
REVISION LIST....................................................................................................................3
CHAPTER 1 SYSTEM SPECIFICATION ......................................................................... 4
Product Specification.................................................................................................................... 4Electrical Specification.............................................................................................11Power Supply Specification.....................................................................................15
System Block Diagram............................................................................................................... 16Product Overview........................................................................................................................ 17
CHAPTER 2 SYSTEM UTILITIES.................................................................................. 21
Firmware Upgrade SOP............................................................................................................. 21Method to enter factory menu................................................................................................... 29EDID Upgrade SOP.................................................................................................................... 30Serial Number Upgrade SOP.................................................................................................... 33How to Change Model name..................................................................................................... 35
CHAPTER 3 SYSTEM DISASSEMBLING AND REPLACEMENT................................ 36
Main Unit Disassembling............................................................................................................ 36Module Assembly Key Point - Optical Engine........................................................................ 41Module Assembly Key Point Mechanical............................................................................. 54
CHAPTER 4 TROUBLESHOOTING.............................................................................. 71
System Analysis.......................................................................................................................... 71Optical Problems Checking Items............................................................................................ 72Power Supply Problems Checking Flow................................................................................. 74LED Messages Definition........................................................................................................... 75Error Count Messages Definition.............................................................................................. 76RS232 Connection...................................................................................................................... 77Adjustment / Alignment Procedure........................................................................................... 79
CHAPTER 5 FRU LIST..................................................................................................84
Exploded Diagram....................................................................................................................... 84Module 1 Total Exploded View............................................................................................... 84Module 2 ASSY UPPER CASE............................................................................................. 86Module 3 ASSY LOWER CASE............................................................................................ 87Module 4 ASSY FRONT CASE............................................................................................. 88FRU List........................................................................................................................................ 89
APPENDIX A - CODE LIST: IR / RS232 / DDC DATA........................................................94
1. Remote Control Code:........................................................................................................... 942. RS-232 Command Code....................................................................................................... 963. DDC Data................................................................................................................................. 98
5/27/2018 Acer x1130p, x1130pa, x1230pk,x1230p,x1230pa,x1237 Projectors Sm
3/109
Revision List
VersionRelease
DateRevision History
Vendor
Model
Name
Rev0 2009.07.16 First Release
Rev0 2009.07.20 Modify FRU Listservice lamp P/N
Rev0 2009.07.27(P.5) Modify SPEC : Projection Offset = 120% 5%
Rev1 2009.07.29
Add X1230PK different part :(1) Ch1- SPEC,(2) Ch3- Disassembly process, Module Assembly Key Point(3) Ch4- alignment procedure(4) Ch5-FRU List(5) Appd. A- DDC table
Rev2 2009.09.11
Add X1130PA different part :(1) Ch1- SPEC,
(2) Ch3- Disassembly process, Module Assembly Key Point(3) Ch4- alignment procedure(4) Ch5-FRU List(5) Appd. A- DDC table
Rev3 2009.09.23 Add X1230P, X1230PA, X1237 different part(1) Ch1-SPEC(2) Ch2-How Change Model Name for X1230P/X1230PA/X1237(3) Ch3- Disassembly process(4) Ch4-Adjustment / Alignment Procedure(5) Ch5-FRU List(6) Appendix A-Remote Control Code(7) Appd. A- DDC table
5/27/2018 Acer x1130p, x1130pa, x1230pk,x1230p,x1230pa,x1237 Projectors Sm
4/109
Chapter 1 System Specification
Product Specification
1.0 Optical Performance
2.0 Image Quality3.0 Mechanical Specification
4.0 Packaging
5.0 Thermal Specification
6.0 Environmental
7.0 Regulatory
8.0 Reliability
9.0 Power Requirements
10.0 Panel Specification
11.0 Compatibility
12.0 Image Interface
13.0 Control Interface
14.0 User Interface
5/27/2018 Acer x1130p, x1130pa, x1230pk,x1230p,x1230pa,x1237 Projectors Sm
5/109
1.0 Optical PerformanceTested under 60 (diagonal) image size with Wideprojection lens position unless other specified.
1.1 ANSI BrightnessX1130P/X1130PA/X1230P: Minimum 2000 LumensX1230PK/X1230PA : Minimum 1840 LumensX1237 Minimum 2400 Lumens
1.2 Brightness Uniformity1.2.1 ANSI Uniformity Minimum 55%
1.2.2 JBMA Uniformity Minimum 75%
1.2.3 Upper-Downunbalance
0.5~2
1.2.4 Left-Rightunbalance
0.6~1.67
1.3 Contrast Ratio
1.3.1 ANSI Contrast Minimum 150:1
1.3.2 FOFO Contrastwithout APM
X1130P/X1130PA/X1230P/ X1237: Minimum 1600:1X1230PK/X1230PA: Minimum 1100:1
1.3.3 FOFO Contrast withAPM
X1130P/X1130PA/X1230P/ X1237: Minimum 2100:1X1230PK/X1230PA: Minimum 1200:1
1.4 Light Leakage
1.4.1 Light Leakage inActive Area
5/27/2018 Acer x1130p, x1130pa, x1230pk,x1230p,x1230pa,x1237 Projectors Sm
6/109
2.5.2 Clearly FocusRange
1.5~6 m(Spec. defined as item 2.6)
2.6 Focus
2.6.1 Pattern(1) If pattern can be uniformly focused (not worse than LimitSample), then pass!(2) If its difficult to judge, then check 2.6.2
2.6.2 Defocus and Flare
X1130P :Defocus: R
5/27/2018 Acer x1130p, x1130pa, x1230pk,x1230p,x1230pa,x1237 Projectors Sm
7/109
Typical
X1130P/X1130PA/X1230P/X1237:Normal mode: 34dBA @ 232C, CW x2 speedEco mode: 29dBA @ 232C, CW x2 speedNormal mode: 36dBA @ 232C, CW x3 speedEco mode: 31dBA @ 232C, CW x3 speed
X1230PK/X1230PA:
Normal mode: 36dBA @ 23 2C, CW x2 speedEco mode: 31dBA @ 23 2C, CW x2 speed
Normal mode: 38dBA @ 23 2C, CW x3 speed
Eco mode: 33dBA @ 23 2C, CW x3 speed6.3 Audible Noise Level
Maximum
X1130P/X1130PA/X1230P/X1237:Normal mode: 36dBA @ 232C, CW x2 speedEco mode: 31dBA @ 232C, CW x2 speedNormal mode: 38dBA @ 232C, CW x3 speedEco mode: 33dBA @ 232C, CW x3 speed
X1230PK/X1230PA:
Normal mode: 38dBA @ 23 2C, CW x2 speedEco mode: 33dBA @ 23 2C, CW x2 speed
Normal mode: 40dBA @ 23 2C, CW x3 speed
Eco mode: 35dBA @ 23 2C, CW x3 speed
6.4 Altitude
Operating:1. 12,000 feet @ 25C (3.5 hours)2. Altitude Ramp rate:
5/27/2018 Acer x1130p, x1130pa, x1230pk,x1230p,x1230pa,x1237 Projectors Sm
8/109
11.2 VideoNTSC/ NTSC4.43/ PAL (Including PAL-M, PAL-N)/ SECAM/PAL60/
11.3 YpbPrNTSC (480i)/ 480p/ PAL (576i)/ 576p,HDTV (720p/1080i/1080p)
11.4 DDC EDID 1.3
12.0 Image Interface Adhere to Electrical Specification section
12.1 Analog RGB Input
X1130P/X1230PK:15 pin D-Sub (Female) x 1 (Reserved 2ndVGA IN)
G(Y): Video amplitude 0.7/1.0 Vp-p : Impedance 75
RB(CbCr): Video amplitude 0.7 Vp-p : Impedance 75HD/VD/CS: TTL Level
X1130PA/ X1230P/ X1237 /X1230PA:15 pin D-Sub (Female) x 2
G(Y): Video amplitude 0.7/1.0 Vp-p : Impedance 75
RB(CbCr): Video amplitude 0.7 Vp-p : Impedance 75
HD/VD/CS: TTL Level12.2 Video Input
RCA jack (Yellow)
Video amplitude 1.0 Vp-p: Impedance 75
12.3 S-Video Input
4 pin Mini-Din (Female)
Y: Luminance amplitude 1.0 Vp-p: Impedance75
C: Chroma amplitude 0.286 Vp-p : Impedance75
12.4 YPbPr Input 15 pin D-Sub (Female) x 1
Y: Luminance amplitude1.0 Vp-p: Impedance 75
PbPr/CbCr: Chroma amplitude 0.7 Vp-p : Impedance 75
12.5 Analog RGB Output X1130P : None
X1130PA/X1230PK/X1230P/ X1237/ X1230PA:15 pin D-Sub (Female) x 1 (Only support D-sub 1)
G(Y): Video amplitude 0.7/1.0 Vp-p : Impedance 75
RB(CbCr): Video amplitude 0.7 Vp-p : Impedance 75HD/VD/CS: TTL Level
13.0 Control Interface
13.1 IR ReceiverIR Receiver x 2 (Front/Top)
Angle: 0Distance 0~10m ; 40Distance 0~8m
13.2 Serial ConnectorRS232 Mini DIN 3pin,command table adhere to Electrical Specification section
13.3 USB ConnectorX1130P : NoneX1130PA/ X1230PK/ X1230P/ X1237/ X1230PA: Mini USBTYPE B Terminal for page up/down
14.0 User Interface Adhere to Electrical Specification section
14.1 Operator Keypad9 Keys:Power ; Source ; Resync ; e ; Menu ; Left ; Right ;Up(Keystone-) ; Down(Keystone+)
14.2 Indicators3 LEDs:Power On/Off Status; Lamp Status; Temperature Status
14.3 Electric Keystone Manual vertical keystone and adjustable range 40
14.4 Auto Ceiling mount
detection
X1130P/X1130PA : None
X1230PK/ X1230P/X1237/ X1230PA: Projector willauto-detect and project by aligned screen likeauto-keystone effect no matter which projection method
5/27/2018 Acer x1130p, x1130pa, x1230pk,x1230p,x1230pa,x1237 Projectors Sm
9/109
(Front, Rear).
15.0 Audio X1130P: NoneX1130PA / X1230PK/X1230P/ X1237/ X1230PA: see belowSPEC
15.1 PC Audio Input X1130PA / X1230PK/X1230P/ X1237/ X1230PA:
3.5mm stereo mini jack
500mVrms 10 Kor more
15.2 SpeakerX1130PA /X1230PK / X1230P/ X1237/ X1230PA:
Speaker 82W X 1, Amplifier 1W X1
16.0 Lamp hourLamp hour = [Hour used in Normal Mode] + 3/4 *[Hour usedin Eco. Mode]
17.0 Closed Caption (CC)
17.1 CC version CC1/CC2/CC3/CC4
18.0 Instant On
(Running change to phase-in X1130P/X1130PA /X1230PK /X1230P/ X1237/ X1230PA MP stage)After turn off projector, there is 120 seconds called Instant
On stage. At this stage, user can turn on the projector. Aftetthis stage, projector will cooling for 20 seconds, and allkeypads are not allowed to operate.
19.0 3D Projection(Running change to phase-in X1130P/X1130PA /X1230PK /X1230P/ X1237/ X1230PA MP stage)See below detail description.
3D Projection :
This function is only for 3D contents and must wear 3D glasses.
TI DDP DDP2430 TI DDP DDP2431
Does not support FRC (Frame Rate Conversion) Can not support HQFS 60Hz 3D source from
DVD which need to go thru FRC
Can only support 120Hz 3D source from PC(VGA/DVI/HDMI)
Support FRC (Frame Rate Conversion) Can support HQFS 60Hz 3D source from
DVD which need to go thru FRC
Can support 120Hz 3D source from PC
OSD :
Add 3D, 3D Sync Invert in Image Page
3D Sync Invert is adjustable when above "3D" is on. Otherwise
When 3D is enabled, Display Mode(in Color Page) is not adjustable ().
For DDP2430 models : 3D / 3D Sync Invert , only appear for VGA/DVI/HDMI source.
Disappear if other sources.
For DDP2230/2431 models : no this limitation.
5/27/2018 Acer x1130p, x1130pa, x1230pk,x1230p,x1230pa,x1237 Projectors Sm
10/109
Reminder screen :
Pop-up screen and appear 10 sec in the center of the screen. End-users can press Menu toexit within 10 sec.
(1) When 3D enable, this screen will appear after exit OSD menu.
(2) There has reminder screen if 3D still enable when power on projector.
Priority : PWD login screen (Security fn is on)
Lamp life reminder
3D reminderScreenTimer and other OSD pup-up fn.
5/27/2018 Acer x1130p, x1130pa, x1230pk,x1230p,x1230pa,x1237 Projectors Sm
11/109
Electrical Specification
1. Timing TableThe PC timing is as following:
Resolution ModeRefresh rate
(Hz)
H-frequency
(kHz)
Clock
(MHz)VGA_60 59.940 31.469 25.175VGA_72 72.809 37.861 31.500VGA_75 75.000 37.500 31.500
640 x 480
VGA_85 85.008 43.269 36.000VGA_70 70.087 31.469 28.3221
720 x 400VGA_85 85.039 37.927 35.500
SVGA_56 56.250 35.156 36.000SVGA_60 60.317 37.879 40.000SVGA_72 72.188 48.077 50.000SVGA_75 75.000 46.875 49.500
800 x 600
SVGA_85 85.061 53.674 56.250XGA_60 60.004 48.363 65.000XGA_70 70.069 56.476 75.000XGA_75 75.029 60.023 78.750
1024 x 768
XGA_85 84.997 68.677 94.500SXGA_70 70.012 63.851 94.500
1152 x 864SXGA_75 75.000 67.500 108.000
1152 x 864 SXGA_85 84.990 77.094 121.500SXGA_60 60.020 63.981 108.000SXGA_72 72.000 76.970 134.600
SXGA_75 75.025 79.976 135.0001280 x 1024
SXGA_85 85.024 91.146 157.500QuadVGA_60 60.000 60.000 108.000
1280 x 960QuadVGA_75 75.000 75.000 126.000
1400 x 1050 SXGA+_60 59.978 65.317 121.7501600 x 1200 UXGA_60 60.000 75.000 162.000
640x480@60Hz Mac G4 59.940 31.469 25.170640x480@67Hz MAC13 66.667 35.000 30.240800x600@60Hz Mac G4 60.317 37.879 40.000832x624@75Hz MAC16 74.546 49.722 57.280
1024x768@60Hz Mac G4 60.004 48.363 65.0001024x768@75Hz MAC19 75.020 60.241 80.0001152x870@75Hz MAC21 75.061 68.681 100.00
WXGA_60 59.870 47.776 79.500WXGA_75 74.893 60.289 102.2501280 x 768
WXGA_85 84.837 68.633 117.5001280 x 720 WXGA_60 60.000 45.000 74.2501280 x 800 WXGA_60 59.810 49.702 83.5001440 x 900 WXGA+_60 59.887 55.935 106.5001680 x 1050 1680x1050_60 59.954 65.290 146.2501920 x1080 1920x1080_60 60.000 67.500 148.500
1366 x 768 acer_16:9 59.790 47.712 85.5001024 x 600 acer_timing 60.000 37.500 50.400640 x 480 VGA_120 119.518 61.910 52.500
5/27/2018 Acer x1130p, x1130pa, x1230pk,x1230p,x1230pa,x1237 Projectors Sm
12/109
800 x 600 SVGA_120 119.854 77.425 83.0001024 x 768 XGA_120 119.804 98.958 137.750
Note3D timing will phase in after MP when 3D function ready
YPbPr support timing is as following:
Signal format fh(kHz) fv(Hz)480i(525i)@60Hz 15.73 59.94
480p(525p)@60Hz 31.47 59.94576i(625i)@50Hz 15.63 50.00
576p(625p)@50Hz 31.25 50.00720p(750p)@60Hz 45.00 60.00720p(750p)@50Hz 37.50 50.001080i(1125i)@60Hz 33.75 60.001080i(1125i)@50Hz 28.13 50.00
1080P@60HZ 67.5 60.001080P@50Hz 56.26 50.00
Video, S-Video support timing is as following:
Video mode fh(kHz) fv(Hz) fsc(MHz)NTSC 15.73 60 3.58PAL 15.63 50 4.43
SECAM 15.63 50 4.25 or 4.41PAL-M 15.73 60 3.58PAL-N 15.63 50 3.58PAL-60 15.73 60 4.43
NTSC4.43 15.73 60 4.43
2. Characteristics of inputs/outputsSignal Parameter Min Type Max
Impedance 75 OhmAmplitude 0.7 Volts peak-to-peakBlack pedestal 0 Volts
RDATAGDATABDATA
Pixel Clock 165 M HzImpedance 75 OhmAmplitude 1 Volts peak-to-peakVideo amplitude 0.7 Volts peak-to-peak
Sync amplitude 0.3 Volts peak-to-peakBlack pedestal 0 Volts
GDATA_SOG
Pixel Clock 165 M HzImpedance 1 K ohmAmplitude, low level 0 0.8 voltAmplitude, high level 2.5 5 Volt
HDATA
Frequency 31 93 K HzImpedance 1 K ohmAmplitude, low level 0 0.8 voltAmplitude, high level 2.5 5 Volt
VDATA
Frequency 48 120 HzAmplitude, low level 0 0.8 voltSDADATAAmplitude, high level 2.5 5 Volt
5/27/2018 Acer x1130p, x1130pa, x1230pk,x1230p,x1230pa,x1237 Projectors Sm
13/109
Amplitude, low level 0 0.8 voltSCLDATAAmplitude, high level 2.5 5 Volt
RXD Amplitude -25 25 VoltTXD Amplitude -13.2 13.2 Volt
Amplitude, total (video+sync)
1 Volts peak to peak
Amplitude, video 0.7 Volts peak to peakAmplitude, sync 0.3 Volts peak to peak
CVBSLuminance
Impedance 75 ohmAmplitude 300 m Volts peak to peakCVBS
Chroma Impedance 75 ohmImpedance (audio in) 10 KohmAmplitude (audio in) 0 0.50 Volts rmsBandwidth 300H
z16kH
zS/N Ratio 40 %
Audio(forX1130PA /X1230PK/X1230P/X1237/X1230PA)
Total HarmonicDistortion
10 %
3. Electrical Interface CharacterInterface Definition
15 pin definition of the mini D-sub male for DDC2B protocol
Pin Definition Pin Definition Pin Definition Pin Definition
1 Red video(Pr)
2 Green Video(Y)
3 Blue Video(Pb)
4 NC
5 NC 6 Red Video Return 7 Green VideoReturn
8 Blue VideoReturn
9 DDCP 5V 10 GND 11 GND 12 Bi-directionaldata (SDA)
13 HorizontalSync
14 Vertical Sync 15 Data clock(SCL)
Video Input
S-Video inputPin Description1 GND
2 GND3 Luminance4 Chroma
Pin Definition
1 Composite video input
5/27/2018 Acer x1130p, x1130pa, x1230pk,x1230p,x1230pa,x1237 Projectors Sm
14/109
Control Port
Mini USB TYPE B (forX1130PA /X1230PK/ X1230P/ X1237/ X1230PA)
4. Functionality
External Message indicator
Message Occasion
D-sub /Composite Video /S-Video Searching The system does not detect the signalInput Not Supported The signal is over the specificationLamp is approaching the end of its useful life in full
power operation. Replacement suggested!
Lamp Hour is at 2970 hours
Pin Description1 TX2 RX3 GND
Pin Description1 Vbus2 D-3 D+4 ID
5 GND
5/27/2018 Acer x1130p, x1130pa, x1230pk,x1230p,x1230pa,x1237 Projectors Sm
15/109
Power Supply Specification
1. Input Power SpecificationSpecification Description
Input Voltage Range The unit shall meet all the operating requirements with the
range 90 ~ 264 VACFrequency Range The unit shall meet all the operating requirements with an input
frequency range 47 Hz ~ 63 HzPower Consumption Normal operation: 280W (Max)
standby mode: < 1W (loop through is disabled), at100~240VAC
Regulation Efficiency 85 % (typical) measuring at 115Vac and full load
2. Output Power RequirementThe power supply can provide DC 12V output as below
NO. Voltage Regulation Load Current Range Ripple & Noise
1 +12 V 5 % 0.15 A ~ 2.5 A 120mV/240 mV
2 +5 V 5 % 0.04 A ~ 0.5 A 50mV/100 mV
The power supply can provide DC 380V output as below
NO. Voltage Range Load Current
1 380 V 370~400V 0.5 A TYP.
3. Lamp Power specifications
Specification DescriptionApplicable Lamp Philips Normal 189W, ECO 163W AC operationStarting pulse from Ignitor 2.5KV
4. Power ProtectionItem CriteriaShort protection No damageOVP 16Vdc Max@12V
6.5Vdc Max@5VOPP DC-DC 130~250%
PFC 130~160%
5. Surge test: Meet EN61000-4-5
LN 1KV, L, N PE 2KV, Criteria B
Electrical Fast Transients (EFT):Meet EN61000-4-4
1 KV, Criteria B7. Voltage Dips: Meet EN61000-4-11
>95% reduction for 0.5 periods, Criteria BHarmonic current test: Meet EN61000-3-2
5/27/2018 Acer x1130p, x1130pa, x1230pk,x1230p,x1230pa,x1237 Projectors Sm
16/109
System Block Diagram
5/27/2018 Acer x1130p, x1130pa, x1230pk,x1230p,x1230pa,x1237 Projectors Sm
17/109
Product Overview
5/27/2018 Acer x1130p, x1130pa, x1230pk,x1230p,x1230pa,x1237 Projectors Sm
18/109
5/27/2018 Acer x1130p, x1130pa, x1230pk,x1230p,x1230pa,x1237 Projectors Sm
19/109
5/27/2018 Acer x1130p, x1130pa, x1230pk,x1230p,x1230pa,x1237 Projectors Sm
20/109
5/27/2018 Acer x1130p, x1130pa, x1230pk,x1230p,x1230pa,x1237 Projectors Sm
21/109
Chapter 2 System Utilities
Firmware Upgrade SOP
Basic Operating
Standby Mode
When standby mode, system power consumption willbe less than 1 Watt.
If user wants to enter this mode, user can just plug inpower cord. Power, Lamp, Temp LED will show Red for1 sec then power LED show red continuouslyas thefigure shown. When the power LED shows Red, it meanssystem is ready for standby.
Besides, user can press power key to turn on projectorafter plugging in power cord when power led is red.
Download ModeThis mode is applied for Download firmware.If operator wants to enter this mode, he should press
and hold keypad Power and Menu together, then plugin power cord. Release the two keypads. Power,Lamp, Temp LED will show red light continuously.Indownload mode, you can use DLP composer to downloadnew firmware and power LED will show purple whiledownloading.
Download WT6702 MCU Code(in Low-Power 1 Watt Standby)
System needs a few sec to download WT6702 MCU automatically.
When DownloadingTemp LED will show red.
When Download SuccessSystem will go back Low-Power standby mode and Power LED
will show red.When Download Fail: Lamp LED will show red.
Standby Mode
Download Mode
5/27/2018 Acer x1130p, x1130pa, x1230pk,x1230p,x1230pa,x1237 Projectors Sm
22/109
DLP Composer LIte Installation Process
(1) Installation
1. Double click the Setup file for DLP Composer Lite(to unzip TI Download Tool V1.1 (forDDP243x).rar to start to install program.
2. When the Installation Wizard appears, click Next.
3. Select to accept the License Agreement, than click Next
4. Click Next in the following steps to continue installation process.
5/27/2018 Acer x1130p, x1130pa, x1230pk,x1230p,x1230pa,x1237 Projectors Sm
23/109
Note:The default installation directory is:C:\Program Files\DLP Composer Lite9.2If you want to install to a different directory (perhapsalongside a prior release of DLP Composer Lite),click the "Browse" button on the "Select Features"
page.
5. When finishing installation, click Finish, and then restart your computer to complete the
installation process.
5/27/2018 Acer x1130p, x1130pa, x1230pk,x1230p,x1230pa,x1237 Projectors Sm
24/109
(2) Setting for your first use
Select Library:1. When start to use this program to download at first time, you need to check if the library
folder is existed under the path of Library.
2. Check if there are library files in the assigned path. If not, unzip the library file into the path.
ClickClickClickClick BrowseBrowseBrowseBrowse totototo selectselectselectselectpath for library filespath for library filespath for library filespath for library files
Click theClick theClick theClick the librarylibrarylibrarylibraryfolder to assignfolder to assignfolder to assignfolder to assignthe path.the path.the path.the path.
Then ClickThen ClickThen ClickThen Click OKOKOKOK....
5/27/2018 Acer x1130p, x1130pa, x1230pk,x1230p,x1230pa,x1237 Projectors Sm
25/109
Set communication (for download by RS232):1. Select Edit->Preference.
2. Select Communications-> Serial Port -> Config.
3. Make sure the settings are the same as below figure-> Click OK.
4. Click OK.
5/27/2018 Acer x1130p, x1130pa, x1230pk,x1230p,x1230pa,x1237 Projectors Sm
26/109
(1) Download Procedure
Notice: for X1130P, since the Main board P/Ns are different in with-3D and without-3Dfunction SKUs, need to download correct FW into corresponding Main board.
How to downloadHardware required
1. Standard RS232 Download cable2. Personal computer or laptop computer
Software required1. DLP Composer Lite program2. New version FW
Download procedure1. Connect RS-232 cable to PC and projector2. Let projector be in Download Mode :
-> Press and hold keypad Power and Menu together, then plug in power cord.-> Release the two keypads.->Power, Lamp, Temp LED will show red light continuously.
3. Execute DLP Composer Lite 9.2 program
4. To select the RS-232 communications interface, choose "Preferences" from the"Edit" menu, click the "Communications" page and choose "Serial Port".
5/27/2018 Acer x1130p, x1130pa, x1230pk,x1230p,x1230pa,x1237 Projectors Sm
27/109
5. Click on Flash Loader and browse the image file (new version firmware)
6. Select Complete Image Download, and make sure to check Skip Boot loader area(32KB)
5/27/2018 Acer x1130p, x1130pa, x1230pk,x1230p,x1230pa,x1237 Projectors Sm
28/109
7. Press Reset Bus and check the status which should show Bus Reset
8. Press Start Download to begin update new firmware.
9. Press Yes to continue. (when download new firmware and power LED will showpurple.)
5/27/2018 Acer x1130p, x1130pa, x1230pk,x1230p,x1230pa,x1237 Projectors Sm
29/109
10. Wait till composer lite notice download complete.
When download complete, LED signal on projector will show standby status.
Method to enter factory menu
1. Press keypad Power and image will show Power Down OSD function2. Press keypad Left twice then press Menu, then enter the Factory mode.
Step 1 Step 2
5/27/2018 Acer x1130p, x1130pa, x1230pk,x1230p,x1230pa,x1237 Projectors Sm
30/109
EDID Upgrade SOP
Equipment List1. PC : with parallel (printer) port2. EDID Board3. Printer cable : 25pin male-female (connect PC to EDID board)
4. D-sub cable* : with full 15pin (connect EDID board to Projector)5. HDMI cable*(connect EDID board to Projector)6. DVI cable* (connect EDID board to Projector)(*Note: Not every models EDID input (D-sub, DVI, HDMI) is the same. Need to check whatkind of file you need before download.)
Setup Equipment1. Connect between PC, EDID board and the Projector:
2. Need to set Jumper before using EDID board :J6 : 1,2 shortJ8 : 1,2 short
J10 : short
3. How to use Download Tool :
Link to Mainboard :For D-sub DDCdownload
Link to Projector :For HDMI DDCdownload (no need inX1130/ X1230/ X1230S/X1235/ X1230K series)
Link to Projector :ForDVI-D DDC download(no need in X1130/ X1230/
X1230S/ X1235/ X1230Kseries)
25pin male-female
cable (normalprinter cable)
EDID board
PC with parallel(printer) port
Please ignore thisconnector
5/27/2018 Acer x1130p, x1130pa, x1230pk,x1230p,x1230pa,x1237 Projectors Sm
31/109
Software Installation, Un-installation : Unzip the Q-EDID program files in the same directory. Install Q-EDID tool : Execute Install Q-EDID.BAT to install & register EDID Board into
the computer.
Un-install Q-EDID tool : If you want to uninstall this tool, execute UninstallQ-EDID.BAT, then it will remove EDID Board from the computer.
How to use Download Tool :(1) Execute EDID Tools V0.16:
1. Run Q-EDID-V016.exe.
2. Program will appear as below picture.
(2) Write EDID:
When write D-SUB/DVI EDID:1. EDID Type Selection : Choose EDID 128 Bytes.2. Open Files : Click Open File to select file *.DDC
(Note : If your DDC file name is not like *.DDC (e.g. *.2dc), please rename it to *.DDC)
3. Write EDID : Click Write EDID, and it will execute writing process.
4. While complete, it will show message as Write EDID OK.(Note : Check cable connection before write. It will show Write EDID OK even the connection is
not stable.)
5/27/2018 Acer x1130p, x1130pa, x1230pk,x1230p,x1230pa,x1237 Projectors Sm
32/109
(3) Read EDID:
Read D-SUB/DVI EDID:1. EDID Type Selection : Choose EDID 128 Bytes2. Read EDID : Click Read EDID.3. While complete, it will show message Read EDID OK , and the read-out DDC will
show in the table in program.
Important Note :
Be reminded to connect Only One port every time, because the software will not be able toidentify the command signal from which port. After connecting all equipment, always read DDC before writing DDC to ensure the
connection status is OK for writing DDC.
Step1
Step2Step3
Step4
Ste 1
Ste 2
Ste 3
5/27/2018 Acer x1130p, x1130pa, x1230pk,x1230p,x1230pa,x1237 Projectors Sm
33/109
Serial Number Upgrade SOP
Hardware required1. Standard RS232 Download cable2. Personal computer or laptop computer
Software required1. Acer_Service_Tool(Data)_3.1.exe
When need to use this Serial Number Upgrade program:When its time to replace Main board for repair, its necessary to rewrite original S/N and
some adjustment values into new Main board by the following process.
Upgrade procedure1. Prepare the download equipment: RS232 cable connect to PC and projector2. Plug power cord into projector, and the projector will be in stand by mode.3. Execute Acer_Service_Tool(Data)_3.1.exe, and it will appear as below picture.
4. Change to connected COM port and Click Port Open icon.
5. Read data from original Main board:Click Read system Data, and it will read the Adjustment data (except Auto keystonedata) & Serial Number from projector and show the Read complete message ininformation block.
4-1. Change toconnected COM Portnumber
4-2. Click PortOpen
5-1. Click this icon toread all data
5-2. Show ReadComplete!
5/27/2018 Acer x1130p, x1130pa, x1230pk,x1230p,x1230pa,x1237 Projectors Sm
34/109
6. Click Save to save data into the assigned file name.
7. Change new Main board:(1) Unplug power cable and RS232 cable from projector, and change new Main board
into Projector.(2) After changing Main board, reconnect power cable and RS232 cable into Projector.
8. Write S/N & data into new Main board:Press Retrieve System and write Data & SN to projector.
9. Load from data & Retrieve System :(1) Click Load from data and select load file.(2) Click Retrieve System to write the values into main board.
6-1. Click Save icon.
6-2. This window willpop out, and it showsthe file saving folder.
6-3. Enter file name here.Suggest to use SerialNum as the file name.
6-4. Click Save to savedata.
9-1. Click Load FromData to load data.
9-2. Select the filesource
9-3. Click Load tofinish file load.
10. Click Retrieve System
to write data.
5/27/2018 Acer x1130p, x1130pa, x1230pk,x1230p,x1230pa,x1237 Projectors Sm
35/109
How to Change Model name
(Only for X1230P/X1230PA/X1237)
Since X1230P/X1230PA/X1237 use the same Main board, after replacing new Main board, its
necessary to change model name:
1. Enter Factory menu.
2. Go to Page2 (as below figure).
3. Default Model name is X1230P. When change Main board on X1230PA or X1237,
please press right/left key to choose correct model name.
5/27/2018 Acer x1130p, x1130pa, x1230pk,x1230p,x1230pa,x1237 Projectors Sm
36/109
Chapter 3 System Disassembling and ReplacementMain Unit DisassemblingTool : Screw Driver --Hex (#4-40) and Cross(Mechanical : M3,M4, Opt.Engine :M2)Process :
Step Discription Photo Tool
1Disassemble the
screw*5(M3*7L)
screw
driver
2
Take off the the IR
sensor wire from
mainboard, then takeoff upper casemodule,
Notice : When takingoff upper casemodule, don't break
the IR sensor wire.
3Take off the case leftmodule and the front
case module
keypad braket
2
13
4
5
FRONT
IR BD
keypad Rubber
4
(1) Take off screws:
For X1130P :
Disassemble thescrew*2(STAND OFF
XH4#-40*6L).
For X1230PK :
Disassemble the
screw*4(STAND OFF
XH4#-40*6L).
For X1130PA/
X1230P/X1230PA/X12
37:Disassemble the
screw*6(STAND OFF
XH4#-40*6L)(2) Take off the rear
case.
screw
driver
1 234
rear case
12
For X1130P:
For X1230PK: For X1130PA/X1230P/X1230PA/X1237:
1 23 4 5 6
5/27/2018 Acer x1130p, x1130pa, x1230pk,x1230p,x1230pa,x1237 Projectors Sm
37/109
5
Disassemble the
screw*5(M3*5L), and
take off the M/B
shielding.
screw
driver
6
(1)Take off the long
wire (one of twin fan
wire), then
disassemble the twin
fan.
(2)Take off the twin
fan wire from M/B.
7
(1)Take off the C/W
FPC wire, blower fan
wire, C/W sensor wire,
Ballast 5-Pin wireform
M/B.
(2)Take off right cass
module.(X1130PA/X1
230PK/X1230P/X1237
/X1230PA have
Speaker)
twin fan
take off this long wire first
1
23
4
CLAMP
5
wire
C/W FPC wireC/W sensor wire
blower fan wireballast 5pin wire
speaker
For X1130PA/X1230PKX1230P/X1237/X1230PA:
sponge*3
8 Take off the M/BMain BD
Note:Circuit boards > 10cm2has been highlighted with the yellow
rectangle as above image shows. Please detach the Circuit boards andfollow local regulations for disposal.
5/27/2018 Acer x1130p, x1130pa, x1230pk,x1230p,x1230pa,x1237 Projectors Sm
38/109
9
(1)Disassemble the
screw*2(M3*6L), and
take off the lamp door.
(2)Disassemble the
screw*1(M3*4L) and
lamp wire, and take off
the lamp module.
screw
driver
10
(1)Disassemble the
screw*3(M3*8L).
(2)Disassemble the
grounding
screw*1(M4*6L), and
take off the Power B/DSHD.
screw
driver
11
Disassemble thewire*2 and screw*1
(M3*7L), and take off
the power BD and
ballast Mylar.
screw
driver
12
(1)Disassemble the
screw*2(M3*7L), and
take off the lamp box.
(2)Disassembly the
screw*2(M3*8L), and
take off the blower fan
screw
driver
screw*1
grounding screw *1
ballast wire
screw*1
blower fan's
thermal wire
screw*1
screw*1
screw*1screw*1
2
1
Ballast Mylar
Screw*3
Note:Circuit boards > 10cm2has been highlighted with the yellow
rectangle as above image shows. Please detach the Circuit boards andfollow local regulations for disposal.
5/27/2018 Acer x1130p, x1130pa, x1230pk,x1230p,x1230pa,x1237 Projectors Sm
39/109
13
Disassemble the
screw*3(M3*7L), and
take off the OPT eng .
screw
driver
14
Disassemble the
screw*2, the ballast
BD, and
wire*3(M3*5L).
screw
driver
15Take off the push
button .
screw
driver
16
(1)Take off the
gasket*2.
(2)Disassemble the
focus ring.
screw
driver
ringfocus
gasket*2
1 2
3
anchor
point
1
2
3pin wire
5pin wire 2pin wire
push buttonshielding
17
Take off th LENS
screw*3(M3*4L) and
Ring Zoom and Ring
Focus
screw*2(M2*3.5L)
screw
driver
1
3
2 1 2
5/27/2018 Acer x1130p, x1130pa, x1230pk,x1230p,x1230pa,x1237 Projectors Sm
40/109
18
Disassemble the
screw*4(M3*7.5L),
and take off the
HSINK and DMD chip
with Chip BD.
screw
driver
19
(1)Disassemble the
baffle DMD.
(2)Disassemble the
screw*3(M3*4L) and
take off the CW
module.
screw
driver
20
Rotate to open the
switch on socket, and
take off the DMD
chip.
screw
driver
21
(1)Disassemble ILL
module screw*2
(M2.5*5L).
(2)Take off
screw*1(M2*8L), FM
holder, fold mirror, FM
clip*2, clip CM front,
clip CM side and
sponge.
screw
driver
22
(1)Disassembly the
screw*1(M2*3L).
(2)Take off the LP
module and LP
screw*2(M2*8L).
screw
driver
1
2
3
4
3
screw*1
1
2sponge
screw*1
1
2
1
2
CW module
baffle DMD
L/P
Note:Circuit boards > 10cm2has been highlighted with the yellow
rectangle as above image shows. Please detach the Circuit boards and
follow local regulations for disposal.
5/27/2018 Acer x1130p, x1130pa, x1230pk,x1230p,x1230pa,x1237 Projectors Sm
41/109
Module Assembly Key Point - Optical Engine
1. Light Pipe Module assembly and overfill alignment
1.1 Assembly LP Module to HSG DMD
(1) Assembly two Overfill adjustment screws to HSG DMD (Fig. 1-1).
** Adjustment criteria refer to below item
(2) Assembly Clip LP and lock with screw well (Fig. 1-2).
(3) Press CLIP of RE_BKT_LP first, and then push it into the hole (Fig. 1-3).
(4) Placed LP Module on LP datum of DMD HSG and adjustment screw well (Fig.1-4).
(5) Assembly Baffle LP first (Fig. 1-5-1) & push Baffle LP to hook DMD HSG, and then
lock with screw well (Fig. 1-5-2).
1.2 Overfill Adjustment @ LP Module
Overfill Adjustment Criteria:(1) Pre-assembly 2 adjusting screws. Criteria shown as Fig.1-6.
(2) Alignment Sequence:
a. To adjust Horizontal Adjustment Screw firstly, and then Vertical Adjustment
Screw.
b. Refer to Fig. 1-6.
(3) For Overfill Re-adjustment:
a. Those 2 Adjustment Screws must be released closely to the Pre-assembly
positions first.
b. Follow adjustment steps shown in Item 1.2.
Fig. 1-1 Fig. 1-2
Overfill VerticalAdjustment Screw
Overfill HorizontalAdjustment Screw
Clip LP
5/27/2018 Acer x1130p, x1130pa, x1230pk,x1230p,x1230pa,x1237 Projectors Sm
42/109
Fig. 1-3
Fig. 1-4
1. Press downthe Clip
2. Insertthe LPModule
Overfill adjustment screwsLP Datum of DMD HSG
5/27/2018 Acer x1130p, x1130pa, x1230pk,x1230p,x1230pa,x1237 Projectors Sm
43/109
Fig. 1-5-1 Fig. 1-5-2
Fig. 1-6
1. Place Clips onBKT surface
2. Push Baffle LPto hook DMD HSG
3. Lock screw
Pre assemble this screwnot over the side surface.
Pre assemble this screw notover the bottom surface.
5/27/2018 Acer x1130p, x1130pa, x1230pk,x1230p,x1230pa,x1237 Projectors Sm
44/109
2. Assembly FM Module:Place FM on HLD FM surface(Fig. 2-1) and use Clip FM to fix FM(Fig. 2-2).
Fig. 2-1 Fig. 2-2
3. Assembly HSG ILL Module:3.1 CM Assembly
I. Insert Clip CM Side first, and then place Clip Front CM to fixed-shaft of ILL SUB
before locking screw (Fig. 3-1, Fig. 3-2).
II. Assemble CM to HSG ILL and to make CM contact three datum on the HSG ILLWell (Fig. 3-3).
III. Assemble CLIP TOP CM (with forceps) to the HSG IL (Fig. 3-4,).
IV. To check and make sure CLIP of CM hooks the HSG ILL very Well (Fig. 3-5).
V. Paste Sponge tube AL on cannelure of HSG ILL (Fig. 3-6).6.2 FM Module Assembly
1. FM Module must be placed to fixed shaft and on the datum surface of ILL SUB
and then lock with screw well (Fig. 3-7).
Fig. 3-1 Fig. 3-2
Screw
Clip CM Side
Fixed shaftsof ILL SUB
Touch theside surface
Clip FM hookthe punchpoints
5/27/2018 Acer x1130p, x1130pa, x1230pk,x1230p,x1230pa,x1237 Projectors Sm
45/109
Fig. 3-3
Fig. 3-4 Fig. 3-5
Fig. 3-6
Datum1
Datum2
Datum3
Clip UP CM
Sponge
5/27/2018 Acer x1130p, x1130pa, x1230pk,x1230p,x1230pa,x1237 Projectors Sm
46/109
Fig. 3-7
4. AL, HSG ILL and HSG DMD Assembly:4.1 Placed AL on the HSG DMD. The raised surface of AL shall toward DMD
direction (Fig. 4-1).4.2 To assemble HSG ILL SUB Module with HSG DMD and cover over on AL and the
then lock with screws (Fig. 4-2).
Fig. 4-1 Fig. 4-2
AL
DMD Direction
screw
Fixed shafts& holes
screw
5/27/2018 Acer x1130p, x1130pa, x1230pk,x1230p,x1230pa,x1237 Projectors Sm
47/109
5. DMD and Chip B/D Module:5.1. Judge Chip B/D and DMD alignment keying first (Fig. 5-1, 5-2).5.2. Alight keying and Assemble DMD to Chip B/D (Fig. 5-3).5.3. Push DMD slightly and use screwdriver rotate clockwise button to lock (close notation)DMD on Chip B/D (Fig. 5-4).
Fig. 5-1 Fig. 5-2
Fig. 5-3 Fig. 5-4
5.4 Place Damper on the surface of Chip-BD Fig. 5-5.
.Fig. 5-5
Dam er
Alignment keying
ButtonOpen notation
Close notation
5/27/2018 Acer x1130p, x1130pa, x1230pk,x1230p,x1230pa,x1237 Projectors Sm
48/109
6. Assembly Optical Engine:6.1 Assemble BKT Link Lamp & CW shield on DMD HSG and then lock with screws well(Fig. 6-1).
Fig. 6-17. Assembly OP ENG
7.1 Assemble Baffle DMD to HSG DMD (Fig.7-1).
7.2 Assemble Sponge DMD to HSG DMD (Fig.7-1).
7.3 Assemble Chip B/D Module to HSG DMD (Fig. 7-2).
Fig.7-1
Screw
Shield CW
BKT LinkLamp
Baffle DMD
Sponge DMD
Alignment keying
5/27/2018 Acer x1130p, x1130pa, x1230pk,x1230p,x1230pa,x1237 Projectors Sm
49/109
Fig.7-2-1
Fig.7-2
7.4 Assemble Thermal Pad & Gasket Hest-sink then place contact DMD (Fig. 7-3).
i. Pre-fastening Sequence: [ 1 ] - [ 2 ] - [ 3 ] - [ 4 ].
ii. Fastening Sequence: [ 2 ] - [ 1 ] - [ 4 ] - [ 3 ].
iii. Screw Torque must be confirmed to be 6 kg-cm.
Fixed shafts of
DMD HSG
Fixed holes of DMD
5/27/2018 Acer x1130p, x1130pa, x1230pk,x1230p,x1230pa,x1237 Projectors Sm
50/109
Fig. 7-3
7.5 Assemble CW Module to DMD HSG and lock with screws well (Fig.7-4).
Fig.7-4
Gasket
Screw
Fixed shaftsof DMD HSG
Screw
1
2
3
4
5/27/2018 Acer x1130p, x1130pa, x1230pk,x1230p,x1230pa,x1237 Projectors Sm
51/109
7.6 Assemble Mylar Antidust well (Fig. 7-5).
Fig.7-5
7.7 Assemble PL LENS and lock with screws well (Follow MP522 assembly) (Fig. 7-6).
Fig. 7-6
Fixed shafts of DMD HSG
Mylar Antidust
Screw
5/27/2018 Acer x1130p, x1130pa, x1230pk,x1230p,x1230pa,x1237 Projectors Sm
52/109
7.8 Assemble Ring Zoom and lock with screws well (Fig. 7-7).
Fig. 7-7
7.9 Assemble Ring Focus (Fig. 7-8).
Fig. 7-8
Screws* 2PCS
Insert and push Ring Focus until fix on the pin of LENS
5/27/2018 Acer x1130p, x1130pa, x1230pk,x1230p,x1230pa,x1237 Projectors Sm
53/109
7.10 Assemble Lamp Module to BKT Link Lamp and then lock with screw well (Fig. 7-10,
Fig. 7-11).
Fig. 7-10
Fig. 7-11
Screw
Fixed shafts
5/27/2018 Acer x1130p, x1130pa, x1230pk,x1230p,x1230pa,x1237 Projectors Sm
54/109
Module Assembly Key Point Mechanical
1. Assemble Lower case
This module includes LC*1pcs,Sponge*1pcs
SHD LC*1pcsScrew*3pcs
Screw*3pcs
Sponge pasted as lower case, must closedto hook.
5/27/2018 Acer x1130p, x1130pa, x1230pk,x1230p,x1230pa,x1237 Projectors Sm
55/109
2. Lower case and Adjust foot
3. Blower module assemble with LCThis step includes blower module*1pcs and screw2pcs
4. Ballast wire Alignment dressed
It needs screw*2pcs
Spring no bend
Screw*2pcs
5/27/2018 Acer x1130p, x1130pa, x1230pk,x1230p,x1230pa,x1237 Projectors Sm
56/109
The EMI cord will behindthe mylar-ballast
Ballast to Lamp wire shouldalign in to this groove
screws*2
The wire neednt around
this rib.
5/27/2018 Acer x1130p, x1130pa, x1230pk,x1230p,x1230pa,x1237 Projectors Sm
57/109
5. Mylar-ballast and blower module assembly
6. Lamp box assemble with lower case Rib
This step needs screw*2pcs to fix assembly lamp-box with LC!
First: assy Blower module
Second: assy Mylar Ballast
Ballast to Lamp wirealso should align in toMylar Ballast groove
5/27/2018 Acer x1130p, x1130pa, x1230pk,x1230p,x1230pa,x1237 Projectors Sm
58/109
5/27/2018 Acer x1130p, x1130pa, x1230pk,x1230p,x1230pa,x1237 Projectors Sm
59/109
7. PWR BD board must check the height of soldering tin
This step needs check connector and boss height.
A piece of screw*1pcs needs dress.
8. The assembly of OPE and LC
This step needs screw/8F.VA564.7R0*3pcs to tighten.
And the sequence needs obey according to picture.
For EMI, the rubber power is necessary.
This cord direction should like this
Screw*1pc
5/27/2018 Acer x1130p, x1130pa, x1230pk,x1230p,x1230pa,x1237 Projectors Sm
60/109
9. Fix PWR between SHD-PWR and LCAssemble SHD-Power
This assembly includes SHD/3K.0R501.031*1pcs, saddle/4B.0R501.001*1pcs and a
piece of mylar/4K.0R501.001*1pcs.
This step needs screw*4pcs to tighten parts.
Screw*3pcs
Rubber Power
5/27/2018 Acer x1130p, x1130pa, x1230pk,x1230p,x1230pa,x1237 Projectors Sm
61/109
Confirm the position of EMI cord right.
Screw
Screw
5/27/2018 Acer x1130p, x1130pa, x1230pk,x1230p,x1230pa,x1237 Projectors Sm
62/109
10. Main BD assembly and connector position
Need check the connectors OK completely
This step adds sponge*1pcs
5/27/2018 Acer x1130p, x1130pa, x1230pk,x1230p,x1230pa,x1237 Projectors Sm
63/109
11. Assemble Main BD SHD
CW sensor board wire and CW FPC alignment
Please align the CW FPC, then put the sensor wire into the saddle together.
Second, screw*4pcs will be done firstly.
The add screw*1pcs and clip*1pcsFinally, assemble fan and fix the wire by clip.
Screw*1
First Screw*4pcs
5/27/2018 Acer x1130p, x1130pa, x1230pk,x1230p,x1230pa,x1237 Projectors Sm
64/109
12. Front IR wire to MB alignment
Front IR wire should alignin to these grooves
5/27/2018 Acer x1130p, x1130pa, x1230pk,x1230p,x1230pa,x1237 Projectors Sm
65/109
13. Stick the leakage Mylar
Align IR-holder side (A and B) paste mylar
14. Dress the Inlet-case, outlet-case and rear-case
It is necessary to confirm the position of SHD when assembling the rear-case!
A
B
5/27/2018 Acer x1130p, x1130pa, x1230pk,x1230p,x1230pa,x1237 Projectors Sm
66/109
Please attention a piece of Mylar on Rear-case
Refer to its assembly as follows:
Shield K-LUCK light leakage
Action: add new Mylar at rear case
No adhesive
area
Align this side
Align this side
5/27/2018 Acer x1130p, x1130pa, x1230pk,x1230p,x1230pa,x1237 Projectors Sm
67/109
15. Assembly side case
Assy case-inlet:
Assy case-outlet: (For X1130PA / X1230PK/ X1230P/ X1237/ X1230PA)
It includes Case-outlet*1pcs, sponge*3pcs, speaker*1pcs and screw*2pcs.
5/27/2018 Acer x1130p, x1130pa, x1230pk,x1230p,x1230pa,x1237 Projectors Sm
68/109
For this module, pay attention to the first position of sponge and the orientation of SPK.
16. Assembling the case-upper
Align this side pasted sponge
Push bkt-key and key closed
Add washer and screw to hold key-bkt
5/27/2018 Acer x1130p, x1130pa, x1230pk,x1230p,x1230pa,x1237 Projectors Sm
69/109
Add a piece of sponge for light leakage
17. Ballast to lamp wire alignment
Lamp box should close up the opening of lower case
Lamp connector assemble with rib
5/27/2018 Acer x1130p, x1130pa, x1230pk,x1230p,x1230pa,x1237 Projectors Sm
70/109
18. Lamp Door screw assemble sequence
19. Protect firm at upper case must have no bubbleMust use a scraper to removed the bubbles.
20. Add a piece of Mylar for light leakage
5/27/2018 Acer x1130p, x1130pa, x1230pk,x1230p,x1230pa,x1237 Projectors Sm
71/109
Chapter 4 TroubleshootingSystem Analysis
Keypad LED OK?
Lamp On?
Step
1. Check Lamp Door
2. Check Connection between Power BD and Main BD
3. Check Power Board and Interlock
4. Check Main Board
NO
YES
Step
1. Check Lampen wire , Lamp wire and Ballast wire
2. Check C/W and wire connection
3. Check Main board
4. Check Lamp
5. Check Ballast
NO
No Signal?
Step
1. Check Input Cable2. Check OSD Source set up
3. Check Main board
YES
YES
Power Auto Turn Off?
Step
1. Check OSD Lamp Hours
2. Check Lamp Door
3. Check Lamp still light or not?
4. Check Fan still spin or not?
5. Check Thermal status
YES
NO
IR Remote Control NG?
Step
1. Check Remote module battery
2. Check Remote module
3. Check IR wire between Main board and IR board
4. Check IR Reciver on IR board
YES
Pixel Fail?
Step
1. Check the connection between
Main BD and Chip BD
2. Check the connection between
OP engine and DMD Chip
3. Check Chip board
4. Check Main board
YES
NO
NO
5/27/2018 Acer x1130p, x1130pa, x1230pk,x1230p,x1230pa,x1237 Projectors Sm
72/109
Optical Problems Checking ItemsNo. Item Trouble Shooting Guide
1 Brightness 1. Change lamp
2 Uniformity 1. Change lamp
3 FOFO Contrast
1. Check ADC calibration
2. Check users menu brightness & contrast are default3. Clean DMD
4. Clean PL
5. Check ILL stop assy
4 ANSI Contrast
1. Clean PL
2. Clean DMD
3. Change PL
5 Color1. Check color wheel delay
2. Check CW 50% point. Replace CW if necessary6 Color Uniformity 1. Change lamp
7 Blue Edge
1. Refer to next page
2. Change CM
3. Change SUB HSG
8 Blue/Purple Border
1. Refer to next page
2. Change CM
3. Change SUB HSG
9 Focus 1. Change Projection Lens2. Check PL datum and DMD parallel
10 Dust Clean DMD
11Horizontal/VerticalStrips
1. Check connector between chip BD and Main BD
2. Re-install DMD with chip BD
3. Check if any pin of C-Spring is missing, damaged or dirty
4. Change new Chip BD/C-Spring
5. Change new DMD12 Pixel Fail Change new DMD
5/27/2018 Acer x1130p, x1130pa, x1230pk,x1230p,x1230pa,x1237 Projectors Sm
73/109
Blue Edge Trouble Shooting:
I. Re-adjust Overfill first.For Overfill Re-adjustment:
i. Those 2 Adjustment Screws must be released for around 2 mm first.
ii. Alignment Sequence:
a. To adjust Horizontal Adjustment Screw firstly, then Vertical AdjustmentScrew.
b. Refer to below Figure.
II. Re-assemble LP moduleinclude LP, LP Baffle, LP clip.
(2) Overfill VerticalAdjustment Screw
(1) Overfill HorizontalAdjustment Screw
5/27/2018 Acer x1130p, x1130pa, x1230pk,x1230p,x1230pa,x1237 Projectors Sm
74/109
Power Supply Problems Checking Flow
5/27/2018 Acer x1130p, x1130pa, x1230pk,x1230p,x1230pa,x1237 Projectors Sm
75/109
LED Messages DefinitionExternal Status indicatorLED Name Detailed DescriptionPower LED Display the power on/off sequence statusLamp Status LED Display the Lamp status (Lamp fail, Lamp spoil etc.)Temperature Status LED Display the Thermal status (Fan Fail, Over Temperature, etc.)
Lamp_LED Temp_LED Power_LED Power_LED Red Red Red Blue
Power Plug Flash ON to OFF Flash ON to OFF Flash ON to OFF --
Standby -- -- ON --
Power button ON -- -- -- ON
Lamp retry -- -- --0.5 second H(On), 0.5second L(Off) flashing
Cooling state -- --0.5 second H(ON),0.5 second L(OFF)
flashing--
Power button OFF:Cooling completed;Standby Mode
-- -- ON --
Firmware Download ON ON
Thermal sensor error(T2 8
5
) (LampOver Temperature)OSD showsProjectorOverheated
-- ON -- ON
Thermal sensor error(T1 40 ) OSD
shows ProjectorOverheated
-- ON -- ON
Fan lock error OSDshows red Fan Fail,Will automatically turnoff soon
--0.5 second H(On), 0.5second L(Off) flashing
-- ON
Lamp error (Lamp,ballast)
ON -- -- ON
Color Wheel fail0.5 second H(ON),0.5 second L(OFF)
flashing-- -- ON
5/27/2018 Acer x1130p, x1130pa, x1230pk,x1230p,x1230pa,x1237 Projectors Sm
76/109
Error Count Messages Definition
Error Count Definition Specification
LAMP Fail error LAMP OFF DETECT LAMPLIT
FAN 1 Speed Error LAMP FAN SPEED ERROR SPEED OVER 20%
FAN 2 Speed Error BALLAST FAN SPEED ERROR SPEED OVER 20%
FAN 3 Speed Error BLOWER FAN SPEED ERROR SPEED OVER 20%
Sensor 1 Open Error Main Board SENSOR ERROR DETECT Sensor 1
Sensor 2 Open Error Power board SENSOR ERROR DETECT Sensor 2
Sensor 1 Short Error Main Board SENSOR ERROR DETECT Sensor 1
Sensor 2 Short Error Power board SENSOR ERROR DETECT Sensor 2
Temperature 1 Error over limited temperature N/A
Temperature 2 Error over limited temperature N/A
FAN IC I2C ERROR I2C communication error N/A
Fan 1 :Lamp Fan
Fan 2 :Power Fan
Fan 3 :Blower Fan
Thermal sensor 2
Thermalsensor 1 LED
message
5/27/2018 Acer x1130p, x1130pa, x1230pk,x1230p,x1230pa,x1237 Projectors Sm
77/109
RS232 Connection
1. Connection:Below shows the illustration of connection between PC and Projector.
Make sure that your computer and projector are turned off before connection.
Power on the computer first, and then plug the power cord of the projector. (It maycause Com port incorrect function, if you do not follow this instruction)
Adapters may be necessary depending on the PC connected to this projector. Pleasecontact with your dealer for further details.
2. Hardware connection
5/27/2018 Acer x1130p, x1130pa, x1230pk,x1230p,x1230pa,x1237 Projectors Sm
78/109
Interface SettingsRS-232 protocolBaud Rate 115200 bpsData Length 8 bitParity Check NoneStop Bit 1 bit
Flow Control None
Command CategoryRefer to Appendix A
5/27/2018 Acer x1130p, x1130pa, x1230pk,x1230p,x1230pa,x1237 Projectors Sm
79/109
Adjustment / Alignment Procedure
Content :
1. Color Wheel Delay Alignment2. Overfill adjustment
3. PC Alignment Procedure4. Keystone Calibration
5/27/2018 Acer x1130p, x1130pa, x1230pk,x1230p,x1230pa,x1237 Projectors Sm
80/109
1. Color Wheel Delay Alignment
Procedure:1. Enter Factory Mode2. Enter Block 13. Change CW Delay by adjusting the following gray pattern to smooth
32 Gray pattern
5/27/2018 Acer x1130p, x1130pa, x1230pk,x1230p,x1230pa,x1237 Projectors Sm
81/109
2. Overfill adjustment (Blue Edge adjustment)1. Full White Pattern is suggested for this alignment.2. Adjust 2 LP-alignment Screws (upper side / lower front side of Optical Engine) behind
Color Wheel.3. Alignment Criteria is to adjust these 2 screws until No Dark Edges and No
Shadows can be observed in image.
5/27/2018 Acer x1130p, x1130pa, x1230pk,x1230p,x1230pa,x1237 Projectors Sm
82/109
3. PC Alignment Procedure
OSD Default value:
Item Value
Cal R Offset 512
Cal G Offset 512
Cal B Offset 512Cal R Gain 1024
Cal G Gain 1024
Cal B Gain 1024
YPbPr R Offset 512
YPbPr B Offset 512
Procedure:
Gray Level:
1. Connect power cord, D-sub cable, and pattern generator into projector
2. Light on projector3. Change Timing and pattern of pattern generator4. Timing:
For X1130P/X1130PA : 800*600 @60Hz (SVGA)For X1230PK/X1230P/ X1230PA/ X1237: 1024*768@60Hz (XGA)
5. Pattern: pattern 16. Press keypad Resync to confirm image frame is correct7. Enter factory mode and select 3rd page in factory mode8. Set Factory values to default9. Change Timing and pattern of pattern generator10. Timing:
For X1130P/X1130PA : 800*600 @60Hz (SVGA)For X1230PK/ X1230P/ X1230PA/ X1237: 1024*768@60Hz (XGA)
11. Pattern: As Figure above {A near white color (240,240,240) and a near black color(16,16,16)}
12. Press Calibration RGB to let the black level to just distinguish, and the light outputof white level to just max
13. Check the 32 levels of gray. All steps must appear14. Done.
White-black pattern
5/27/2018 Acer x1130p, x1130pa, x1230pk,x1230p,x1230pa,x1237 Projectors Sm
83/109
4. Keystone Calibration
ConditionHorizontal plane(0)
1. Make projector be horizontal2. Enter factory menu
3. Enter into Block 3 in factory menu4. Select item AutoKeystoneCal5. Press key Left or Right to do auto calibration6. Finish 0 calibration and bellow items will show data :
AutoKeystoneXCal: 5 AutoKeystoneXOffset: 20
5/27/2018 Acer x1130p, x1130pa, x1230pk,x1230p,x1230pa,x1237 Projectors Sm
84/109
Chapter 5 FRU ListExploded Diagram
Module 1 Total Exploded View
5/27/2018 Acer x1130p, x1130pa, x1230pk,x1230p,x1230pa,x1237 Projectors Sm
85/109
5/27/2018 Acer x1130p, x1130pa, x1230pk,x1230p,x1230pa,x1237 Projectors Sm
86/109
Module 2 ASSY UPPER CASE
5/27/2018 Acer x1130p, x1130pa, x1230pk,x1230p,x1230pa,x1237 Projectors Sm
87/109
Module 3 ASSY LOWER CASE
5/27/2018 Acer x1130p, x1130pa, x1230pk,x1230p,x1230pa,x1237 Projectors Sm
88/109
Module 4 ASSY FRONT CASE
5/27/2018 Acer x1130p, x1130pa, x1230pk,x1230p,x1230pa,x1237 Projectors Sm
89/109
FRU List
Model CATEGORY PARTNAME ACER PART NO. Photo
X1130P ACCESSORY
Projector RemoteControl Qisda RCQ5 layout (25keys w/o Laser,w/o Mouse, withPgUp/PgDn)
VZ.K0300.002
X1130PA/X1230PK/X1230PA/X1230P/X1237
ACCESSORY
Projector RemoteControl Qisda RCQ3 layout (25keys w/o Laser,Mouse,PgUp/PgDn)
VZ.K0300.001
X1130P BOARDMAIN BOARD(W/KEYPADBOARD)
55.K060Q.001
X1130PA BOARDMAIN BOARD (W/KEYPADBOARD)
55.K090Q.001
X1230PK BOARDMAIN BOARD(W/KEYPADBOARD)
55.K030Q.001
X1230PA/X1230P/X1237
BOARDMAIN BOARD(W/KEYPADBOARD)
55.K100Q.001
X1130P/X1130PA/X1230PK/X1230PA/X1230P/X1237
BOARDBALLAST (LAMPDRIVER)
55.K060Q.002
X1130P/X1130P
A/X1230PK/X1230PA/X1230P/X1237
BOARD POWER BOARD 55.K060Q.003
X1130P/X1130PA/X1230PK/X1230PA/X1230P/X1237
BOARD DMD CHIP BAOD 55.K060Q.004
X1130P/X1130PA/X1230PK/X1230PA/X1230P/X1237
BOARDIR SENSORBOARD
55.J900Q.005
5/27/2018 Acer x1130p, x1130pa, x1230pk,x1230p,x1230pa,x1237 Projectors Sm
90/109
X1130P/X1130PA/X1230PK/X1230PA/X1230P/X1237
CABLEPOWER CORDUK
27.LDW0Q.001 -
X1130P/X1130PA/X1230PK/X1230PA/X1230P/X
1237
CABLEPOWER CORDEUR
27.LBJ0Q.001 -
X1130P/X1130PA/X1230PK/X1230PA/X1230P/X1237
CABLEPOWER CORDSWIS
50.LE20Q.004 -
X1130P/X1130PA/X1230PK/X1230PA/X1230P/X1237
CABLEPOWER CORDARF
27.LCE0Q.002 -
X1130P/X1130PA/X1230PK/X12
30PA/X1230P/X1237
CABLEPOWER CORD
US
27.LBJ0Q.002 -
X1130P/X1130PA/X1230PK/X1230PA/X1230P/X1237
CABLEPOWER CORDAUS
27.LBJ0Q.004 -
X1130P/X1130PA/X1230PK/X1230PA/X1230P/X1237
CABLEPOWER CORDCHINA
50.LE10Q.004 -
X1130P/X1130PA/X1230PK/X12
30PA/X1230P/X1237
CABLEPOWER CORD
THAILAND27.J900Q.001 -
X1130P/X1130PA/X1230PK/X1230PA/X1230P/X1237
CABLEPOWER CORDINDIA
27.LCE0Q.001 -
X1130P/X1130PA/X1230PK/X1230PA/X1230P/X1237
CABLEPOWER CORDJP
27.LE20Q.001 -
X1130PA/X1230
P/X1237 CABLE
POWER CORD
KOR 27.K090Q.001
X1130P/X1130PA/X1230PK/X1230PA/X1230P/X1237
CABLE D-SUB CABLE 50.J900Q.001 -
X1230PK/X1230P/X1237
CABLE RCA CABLE 50.J900Q.002
X1130P/X1130PA/X1230PK/X1230PA/X1230P/X
1237
CABLECABLE M/B TOIR BOARD
50.J900Q.003
5/27/2018 Acer x1130p, x1130pa, x1230pk,x1230p,x1230pa,x1237 Projectors Sm
91/109
X1130P/X1130PA/X1230PK/X1230PA/X1230P/X1237
CABLECABLE BALLASTTO LAMP
50.K060Q.001
X1130P/X1130P
A/X1230PK/X1230PA/X1230P/X1237
CABLECABLE POWERBOARD TOBALLAST
50.K060Q.002
X1130P/X1130PA/X1230PK/X1230PA/X1230P/X1237
CABLECABLE M/B TOBALLAST
50.K060Q.003
X1130PCASE/COVER/BRACKET
ASSEMBLY
REAR CASE 60.K060Q.001
X1230PKCASE/COVER/BRACKETASSEMBLY
REAR CASE 60.K030Q.001
X1130PA/X1230PA/X1230P/X1237
CASE/COVER/BRACKETASSEMBLY
REAR CASE 60.K090Q.001
X1130P/X1130PA/X1230PK/X1230PA/X1230P/X1237
CASE/COVER/BRACKETASSEMBLY
INTEL CASE 60.K060Q.002
X1130P/X1130PA/X1230PK/X1230PA/X1230P/X1237
CASE/COVER/BRACKETASSEMBLY
OUTLET CASE 60.J900Q.003
X1130P/X1130PA/X1230PK/X1230PA/X1230P/X1237
CASE/COVER/BRACKETASSEMBLY
UPPER CASE(W/ KEYPADRUBBER&BRACKET)
60.K060Q.003
X1130P/X1130PA/X1230PK/X1230PA/X1230P/X1237
CASE/COVER/BRACKETASSEMBLY
LOWER CASE(W/ ADJUSTFOOT)
60.J900Q.005
X1130P/X1130PA/X1230PK/X1230PA/X1230P/X1237
CASE/COVER/B
RACKETASSEMBLY
FRONT CASE(W/O IR BOARD) 60.J900Q.006
5/27/2018 Acer x1130p, x1130pa, x1230pk,x1230p,x1230pa,x1237 Projectors Sm
92/109
X1130P/X1130PA/X1230PK/X1230PA/X1230P/X1237
CASE/COVER/BRACKETASSEMBLY
LAMP DOOR 60.J900Q.007
X1130P/X1130P
A/X1230PK/X1230PA/X1230P/X1237
CASE/COVER/BRACKETASSEMBLY
ZOOM RING 60.J900Q.008
X1130P/X1130PA/X1230PK/X1230PA/X1230P/X1237
CASE/COVER/BRACKETASSEMBLY
FOCUS RING 60.J900Q.009
X1130P/X1130PA/X1230PK/X12
30PA/X1230P
DIGITAL LIGHTDEVICE
PhillipsX1130P/X1230PKLamp Module
189W, DIT85,DDP2430
EC.K0600.001
X1237DIGITAL LIGHTDEVICE
Lamp Module forX1237 (PhillipsUHP 185-163W/E20.6-B)
EC.K1200.001
X1130P/X1130PA/X1230PK/X1230PA/X1230P/X1237
DIGITAL LIGHTDEVICE
COLOR WHEELMODULE(W/SENSOR BD &CABLE)
57.K060Q.001
X1130P/X1130PA/X1230PK/X1230PA/X1230P/X1237
DIGITAL LIGHTDEVICE
LIGHT PIPE 57.J900Q.002
X1130P/X1130PA/X1230PK/X1230PA/X1230P/X1237
DIGITAL LIGHTDEVICE
LENS 57.K060Q.002
X1130P/X1130PA
DIGITAL LIGHTDEVICE
DMD CHIP 57.K060Q.003
X1230PK/X1230PA
DIGITAL LIGHTDEVICE
DMD CHIP 57.K030Q.001
X1230P/X1237DIGITAL LIGHTDEVICE DMD CHIP TBC
5/27/2018 Acer x1130p, x1130pa, x1230pk,x1230p,x1230pa,x1237 Projectors Sm
93/109
X1130P/X1130PA
DIGITAL LIGHTDEVICE
ENGINEMODULE
57.K060Q.004
X1230PK/X1230PA
DIGITAL LIGHTDEVICE
ENGINEMODULE
57.K030Q.002
X1230P/X1237DIGITAL LIGHTDEVICE
ENGINEMODULE
TBC
X1130P/X1130PA/X1230PK/X1230PA/X1230P/X1237
FAN FAN (X2) 23.K060Q.001
X1130P/X1130PA/X1230PK/X1230PA/X1230P/X1237
FANFAN BLOWERMODULE
23.K060Q.002
X1130PA/X1230PK/X1230PA/X1230P/X1237
SPEAKER SPEAKER 23.K030Q.001
X1130P/X1130PA/X1230PK/X1230PA/X1230P/X1237
MISCELLANEOUS
FOOT ADJFOOT 47.J900Q.001
X1130P/X1130PA/X1230PK/X1230PA/X1230P/X1237
MISCELLANEOUS
RUBBERADJFOOT PAD
47.J900Q.002
X1130P/X1130PA/X1230PK/X1230PA/X1230P/X1237
JIG BOARDTOOL KIT FOREDID UPLOAD
6K.J900Q.001
(Note) The updated P/N refers to latest Spare Part List
5/27/2018 Acer x1130p, x1130pa, x1230pk,x1230p,x1230pa,x1237 Projectors Sm
94/109
Appendix A - Code List: IR / RS232 / DDC Data
1. Remote Control Code:IR setting value
Frequency: 38kHzProtocal: NEC format
b. IR command codeX1130P:Customer code0813
5/27/2018 Acer x1130p, x1130pa, x1230pk,x1230p,x1230pa,x1237 Projectors Sm
95/109
X1130PA/ X1230PK/ X1230P/ X1230PA/ X1237:Customer code0813
5/27/2018 Acer x1130p, x1130pa, x1230pk,x1230p,x1230pa,x1237 Projectors Sm
96/109
2. RS-232 Command Code
General command type (Projector receives commands)
No Code (character) Function feature Note
1 OKOKOKOKOK Power On support
2 * 0 IR 001 Power On support3 * 0 IR 002 Power Off support
4 * 0 IR 004 Keystone support
5 * 0 IR 006 Mute support
6 * 0 IR 007 Freeze support
7 * 0 IR 008 Menu support
8 * 0 IR 009 Up support
9 * 0 IR 010 Down support
10 * 0 IR 011 Right support
11 * 0 IR 012 Left support
12 * 0 IR 013 Enter Unsupport
13 * 0 IR 014 Re-Sync support
14 * 0 IR 015 Source Analog RGB for D-sub support
15 * 0 IR 016 Source Digital RGB Unsupport
16 * 0 IR 017 Source PbPr for D-sub Unsupport
17 * 0 IR 018 Source S-Video support
18 * 0 IR 019 Source Composite Video support
19 * 0 IR 020 Source Component Video support
20 * 0 IR 021 Aspect ratio 16:9 support
21 * 0 IR 022 Aspect ratio 4:3 support
22 * 0 IR 023 Volume + support
23 * 0 IR 024 Volume support
24 * 0 IR 025 Brightness support
25 * 0 IR 026 Contrast support
26 * 0 IR 027 Color Temperature support
27 * 0 IR 028 Source Analog RGB for DVI Port Unsupport
28 * 0 IR 029 Source Analog YPbPr for DVI Port Unsupport
29 * 0 IR 030 Hide support
30 * 0 IR 031 Source support
31 * 0 IR 032 Video: Color saturation adjustment support
32 * 0 IR 033 Video: Hue adjustment support
33 * 0 IR 034 Video: Sharpness adjustment support
34 * 0 IR 035 Query Model name support
35 * 0 IR 036 Query Native display resolution support
36 * 0 IR 037 Query company name support
37 * 0 IR 040 Aspect ratioL.Box Unsupport38 * 0 IR 041 Aspect ratio 1:1 Unsupport
39 * 0 IR 042 Keystone Up support
40 * 0 IR 043 Keystone Down support
5/27/2018 Acer x1130p, x1130pa, x1230pk,x1230p,x1230pa,x1237 Projectors Sm
97/109
41 * 0 IR 044 Keystone Left Unsupport
42 * 0 IR 045 Keystone Right Unsupport
43 * 0 IR 046 Zoom support
44 * 0 IR 047 e-Key support
45 * 0 IR 048 Color RGB support
46 * 0 IR 049 Language support
47 * 0 IR 050 Source HDMI Unsupport
General command type (Projector transmits commands)
NO Code (character) Function feature Note
1 Model XXXXXXXX Return the Model name support
2 Res XXXXXReturn the Native displayresolution
support
3 Name XXXXXXXX Return the company name support
Lamp command type (Projector receives commands)
NO Code (character) Function feature Note
1 * 0 Lamp ? Query the lamp ON/OFF support
2 * 0 Lamp Query the lamp hours support
Lamp command type (Projector transmits commands)
NO Code (character) Function feature Note
1 Lamp 0 Return Lamp OFF status support
2 Lamp 1 Return Lamp ON status support
3 XXXX Return Lamp hours support
Source command type (Projector receives commands)
NO Code (character) Function feature Note
1 * 0 Src ? Query source input type support
5/27/2018 Acer x1130p, x1130pa, x1230pk,x1230p,x1230pa,x1237 Projectors Sm
98/109
3. DDC Data
X1130P EDID
EDID Block 0, Bytes 0-127 [00H-7FH]Block Type: EDID 1.3
0 1 2 3 4 5 6 7 8 9 A B C D E F
________________________________________________________________0 | 00 FF FF FF FF FF FF 00 04 72 05 06 01 00 00 00
10 | 01 13 01 03 0E 00 00 78 0A D1 8A A5 57 58 96 2320 | 17 50 60 3F CF 80 31 7C 45 7C 61 7C 81 80 81 C030 | 81 00 95 00 B3 00 A0 0F 20 00 31 58 1C 20 28 8040 | 14 00 00 00 00 00 00 1E 00 00 00 FD 00 30 78 1F50 | 5D 11 00 0A 20 20 20 20 20 20 00 00 00 FC 00 5860 | 31 31 33 30 50 0A 20 20 20 20 20 20 00 00 00 FF70 | 00 4B 30 36 30 35 30 30 31 38 34 30 31 0A 00 AF
______________________________________________________________________
(08H-09H) ID Manufacturer Name _________________________ = ACR
(0AH-0BH) Product ID Code ______________________________ = 0605(0CH-0FH) Last 5 Digits of Serial Number _______________ = 00001(10H) Week of Manufacture __________________________ = 01(11H) Year of Manufacture __________________________ = 2009(12H) EDID Version Number __________________________ = 1(13H) EDID Revision Number _________________________ = 3
(14H) VIDEO INPUT DEFINITION:Analog Signal0.700, 0.300 (1.000 Vp-p)Sync on Green, Composite Sync, Separate Syncs
(15H) Maximum Horizontal Image Size ________________ = mm(16H) Maximum Vertical Image Size __________________ = mm(17H) Display Gamma ________________________________ = 2.20
(18H) DPMS and Supported Feature(s):Preferred Timing ModeDisplay Type = R/G/B Color
(19H-22H) CHROMA INFO:Red x - 0.647 Green x - 0.344 Blue x - 0.139 White x - 0.314Red y - 0.341 Green y - 0.587 Blue y - 0.090 White y - 0.377
(23H) ESTABLISHED TIMING I:640 x 480 @ 60Hz (IBM,VGA)640 x 480 @ 67Hz (Apple,Mac II)640 x 480 @ 72Hz (VESA)640 x 480 @ 75Hz (VESA)800 x 600 @ 56Hz (VESA)800 x 600 @ 60Hz (VESA)
(24H) ESTABLISHED TIMING II:800 x 600 @ 72Hz (VESA)800 x 600 @ 75Hz (VESA)1024 x 768 @ 60Hz (VESA)1024 x 768 @ 70Hz (VESA)1024 x 768 @ 75Hz (VESA)1280 x 1024 @ 75Hz (VESA)
(25H) Manufacturer's Reserved Timing:1152 x 870 @ 75Hz (Apple,Mac II)
(38-53) Standard Timing Identification:Standard Timing ID 1: 640 x 480 @120Hz
5/27/2018 Acer x1130p, x1130pa, x1230pk,x1230p,x1230pa,x1237 Projectors Sm
99/109
Standard Timing ID 2: 800 x 600 @120HzStandard Timing ID 3: 1024 x 768 @120HzStandard Timing ID 4: 1280 x 1024 @60HzStandard Timing ID 5: 1280 x 720 @60HzStandard Timing ID 6: 1280 x 800 @60HzStandard Timing ID 7: 1440 x 900 @60HzStandard Timing ID 8: 1680 x 1050 @60Hz
______________________________________________________________________
(36H-47H) Detailed Timing / Descriptor Block 1:800x600 Pixel Clock: 40.00 MHz
______________________________________________________________________Horizontal Image Size: 0 mm Vertical Image Size: 0 mmRefreshed Mode: Non-Interlaced Normal Display - No Stereo
Horizontal:Active Count: 800 pixels Blanking Count: 256 pixelsSync Offset: 40 pixels Sync Pulse Width: 128 pixelsBorder: 0 pixels Frequency: 37.88 kHz
Vertical:Active Count: 600 lines Blanking Count: 28 linesSync Offset: 1 lines Sync Pulse Width: 4 linesBorder: 0 lines Frequency: 60.32 Hz
Digital Separate, Horizontal Polarity (+) Vertical Polarity (+)______________________________________________________________________
(48H-59H) Detailed Timing / Descriptor Block 2:
Monitor Range Limits:Min Vertical Freq - 48 HzMax Vertical Freq - 120 HzMin Horiz. Freq - 31 kHz
Max Horiz. Freq - 93 kHzPixel Clock - 170 MHzGTF - Not Used
______________________________________________________________________
(5AH-6BH) Detailed Timing / Descriptor Block 3:
Monitor Name:X1130P
______________________________________________________________________
(6CH-7DH) Detailed Timing / Descriptor Block 4:
Monitor Serial Number:K06050018401
(7EH) Block No: No Extension EDID Block(s)(7FH) CheckSum OK
5/27/2018 Acer x1130p, x1130pa, x1230pk,x1230p,x1230pa,x1237 Projectors Sm
100/109
X1130PA EDID
EDID Block 0, Bytes 0-127 [00H-7FH]Block Type: EDID 1.3
0 1 2 3 4 5 6 7 8 9 A B C D E F________________________________________________________________
0 | 00 FF FF FF FF FF FF 00 04 72 05 09 01 00 00 0010 | 01 13 01 03 0E 00 00 78 0A D1 8A A5 57 58 96 2320 | 17 50 60 3F CF 80 31 7C 45 7C 61 7C 81 80 81 C030 | 81 00 95 00 B3 00 A0 0F 20 00 31 58 1C 20 28 8040 | 14 00 00 00 00 00 00 1E 00 00 00 FD 00 30 78 1F50 | 5D 11 00 0A 20 20 20 20 20 20 00 00 00 FC 00 5860 | 31 31 33 30 50 41 0A 20 20 20 20 20 00 00 00 FF70 | 00 4B 30 39 30 35 30 30 31 38 34 30 31 0A 00 88
______________________________________________________________________
(08H-09H) ID Manufacturer Name _________________________ = ACR(0AH-0BH) Product ID Code ______________________________ = 0905(0CH-0FH) Last 5 Digits of Serial Number _______________ = 00001(10H) Week of Manufacture __________________________ = 01
(11H) Year of Manufacture __________________________ = 2009(12H) EDID Version Number __________________________ = 1(13H) EDID Revision Number _________________________ = 3
(14H) VIDEO INPUT DEFINITION:Analog Signal0.700, 0.300 (1.000 Vp-p)Sync on Green, Composite Sync, Separate Syncs
(15H) Maximum Horizontal Image Size ________________ = mm(16H) Maximum Vertical Image Size __________________ = mm(17H) Display Gamma ________________________________ = 2.20
(18H) DPMS and Supported Feature(s):
Preferred Timing ModeDisplay Type = R/G/B Color
(19H-22H) CHROMA INFO:Red x - 0.647 Green x - 0.344 Blue x - 0.139 White x - 0.314Red y - 0.341 Green y - 0.587 Blue y - 0.090 White y - 0.377
(23H) ESTABLISHED TIMING I:640 x 480 @ 60Hz (IBM,VGA)640 x 480 @ 67Hz (Apple,Mac II)640 x 480 @ 72Hz (VESA)640 x 480 @ 75Hz (VESA)800 x 600 @ 56Hz (VESA)
800 x 600 @ 60Hz (VESA)
(24H) ESTABLISHED TIMING II:800 x 600 @ 72Hz (VESA)800 x 600 @ 75Hz (VESA)1024 x 768 @ 60Hz (VESA)1024 x 768 @ 70Hz (VESA)1024 x 768 @ 75Hz (VESA)1280 x 1024 @ 75Hz (VESA)
(25H) Manufacturer's Reserved Timing:1152 x 870 @ 75Hz (Apple,Mac II)
(38-53) Standard Timing Identification:Standard Timing ID 1: 640 x 480 @120HzStandard Timing ID 2: 800 x 600 @120HzStandard Timing ID 3: 1024 x 768 @120HzStandard Timing ID 4: 1280 x 1024 @60Hz
5/27/2018 Acer x1130p, x1130pa, x1230pk,x1230p,x1230pa,x1237 Projectors Sm
101/109
Standard Timing ID 5: 1280 x 720 @60HzStandard Timing ID 6: 1280 x 800 @60HzStandard Timing ID 7: 1440 x 900 @60HzStandard Timing ID 8: 1680 x 1050 @60Hz
______________________________________________________________________
(36H-47H) Detailed Timing / Descriptor Block 1:800x600 Pixel Clock: 40.00 MHz
______________________________________________________________________Horizontal Image Size: 0 mm Vertical Image Size: 0 mmRefreshed Mode: Non-Interlaced Normal Display - No Stereo
Horizontal:Active Count: 800 pixels Blanking Count: 256 pixelsSync Offset: 40 pixels Sync Pulse Width: 128 pixelsBorder: 0 pixels Frequency: 37.88 kHz
Vertical:Active Count: 600 lines Blanking Count: 28 linesSync Offset: 1 lines Sync Pulse Width: 4 linesBorder: 0 lines Frequency: 60.32 Hz
Digital Separate, Horizontal Polarity (+) Vertical Polarity (+)______________________________________________________________________
(48H-59H) Detailed Timing / Descriptor Block 2:
Monitor Range Limits:Min Vertical Freq - 48 HzMax Vertical Freq - 120 HzMin Horiz. Freq - 31 kHzMax Horiz. Freq - 93 kHzPixel Clock - 170 MHzGTF - Not Used
______________________________________________________________________
(5AH-6BH) Detailed Timing / Descriptor Block 3:
Monitor Name:X1130PA
______________________________________________________________________
(6CH-7DH) Detailed Timing / Descriptor Block 4:
Monitor Serial Number:K09050018401
(7EH) Block No: No Extension EDID Block(s)(7FH) CheckSum OK
5/27/2018 Acer x1130p, x1130pa, x1230pk,x1230p,x1230pa,x1237 Projectors Sm
102/109
X1230PK EDID
EDID Block 0, Bytes 0-127 [00H-7FH]Block Type: EDID 1.3
0 1 2 3 4 5 6 7 8 9 A B C D E F________________________________________________________________
0 | 00 FF FF FF FF FF FF 00 04 72 05 03 01 00 00 0010 | 01 13 01 03 0E 00 00 78 0A D1 8A A5 57 58 96 2320 | 17 50 60 3F CF 80 31 7C 45 7C 61 7C 81 80 81 C030 | 81 00 95 00 B3 00 64 19 00 40 41 00 26 30 18 8840 | 36 00 00 00 00 00 00 18 00 00 00 FD 00 30 78 1F50 | 5D 11 00 0A 20 20 20 20 20 20 00 00 00 FC 00 5860 | 31 32 33 30 50 4B 0A 20 20 20 20 20 00 00 00 FF70 | 00 4B 30 33 30 35 30 30 31 38 34 30 31 0A 00 B5
______________________________________________________________________
(08H-09H) ID Manufacturer Name _________________________ = ACR(0AH-0BH) Product ID Code ______________________________ = 0305(0CH-0FH) Last 5 Digits of Serial Number _______________ = 00001
(10H) Week of Manufacture __________________________ = 01(11H) Year of Manufacture __________________________ = 2009(12H) EDID Version Number __________________________ = 1(13H) EDID Revision Number _________________________ = 3
(14H) VIDEO INPUT DEFINITION:Analog Signal0.700, 0.300 (1.000 Vp-p)Sync on Green, Composite Sync, Separate Syncs
(15H) Maximum Horizontal Image Size ________________ = mm(16H) Maximum Vertical Image Size __________________ = mm(17H) Display Gamma ________________________________ = 2.20
(18H) DPMS and Supported Feature(s):Preferred Timing ModeDisplay Type = R/G/B Color
(19H-22H) CHROMA INFO:Red x - 0.647 Green x - 0.344 Blue x - 0.139 White x - 0.314Red y - 0.341 Green y - 0.587 Blue y - 0.090 White y - 0.377
(23H) ESTABLISHED TIMING I:640 x 480 @ 60Hz (IBM,VGA)640 x 480 @ 67Hz (Apple,Mac II)640 x 480 @ 72Hz (VESA)640 x 480 @ 75Hz (VESA)
800 x 600 @ 56Hz (VESA)800 x 600 @ 60Hz (VESA)
(24H) ESTABLISHED TIMING II:800 x 600 @ 72Hz (VESA)800 x 600 @ 75Hz (VESA)1024 x 768 @ 60Hz (VESA)1024 x 768 @ 70Hz (VESA)1024 x 768 @ 75Hz (VESA)1280 x 1024 @ 75Hz (VESA)
(25H) Manufacturer's Reserved Timing:1152 x 870 @ 75Hz (Apple,Mac II)
(38-53) Standard Timing Identification:Standard Timing ID 1: 640 x 480 @120HzStandard Timing ID 2: 800 x 600 @120HzStandard Timing ID 3: 1024 x 768 @120Hz
5/27/2018 Acer x1130p, x1130pa, x1230pk,x1230p,x1230pa,x1237 Projectors Sm
103/109
Standard Timing ID 4: 1280 x 1024 @60HzStandard Timing ID 5: 1280 x 720 @60HzStandard Timing ID 6: 1280 x 800 @60HzStandard Timing ID 7: 1440 x 900 @60HzStandard Timing ID 8: 1680 x 1050 @60Hz
______________________________________________________________________
(36H-47H) Detailed Timing / Descriptor Block 1:1024x768 Pixel Clock: 65.00 MHz
______________________________________________________________________Horizontal Image Size: 0 mm Vertical Image Size: 0 mmRefreshed Mode: Non-Interlaced Normal Display - No Stereo
Horizontal:Active Count: 1024 pixels Blanking Count: 320 pixelsSync Offset: 24 pixels Sync Pulse Width: 136 pixelsBorder: 0 pixels Frequency: 48.36 kHz
Vertical:Active Count: 768 lines Blanking Count: 38 linesSync Offset: 3 lines Sync Pulse Width: 6 linesBorder: 0 lines Frequency: 60.00 Hz
Digital Separate, Horizontal Polarity (-) Vertical Polarity (-)
______________________________________________________________________
(48H-59H) Detailed Timing / Descriptor Block 2:
Monitor Range Limits:Min Vertical Freq - 48 HzMax Vertical Freq - 120 HzMin Horiz. Freq - 31 kHzMax Horiz. Freq - 93 kHz
Pixel Clock - 170 MHzGTF - Not Used______________________________________________________________________
(5AH-6BH) Detailed Timing / Descriptor Block 3:
Monitor Name:X1230PK
______________________________________________________________________
(6CH-7DH) Detailed Timing / Descriptor Block 4:
Monitor Serial Number:
K03050018401
(7EH) Block No: No Extension EDID Block(s)(7FH) CheckSum OK
5/27/2018 Acer x1130p, x1130pa, x1230pk,x1230p,x1230pa,x1237 Projectors Sm
104/109
X1230PA EDID
EDID Block 0, Bytes 0-127 [00H-7FH]Block Type: EDID 1.3
0 1 2 3 4 5 6 7 8 9 A B C D E F________________________________________________________________
0 | 00 FF FF FF FF FF FF 00 04 72 05 10 01 00 00 0010 | 01 13 01 03 0E 00 00 78 0A D1 8A A5 57 58 96 2320 | 17 50 60 3F CF 80 31 7C 45 7C 61 7C 81 80 81 C030 | 81 00 95 00 B3 00 64 19 00 40 41 00 26 30 18 8840 | 36 00 00 00 00 00 00 18 00 00 00 FD 00 30 78 1F50 | 5D 11 00 0A 20 20 20 20 20 20 00 00 00 FC 00 5860 | 31 32 33 30 50 41 0A 20 20 20 20 20 00 00 00 FF70 | 00 4B 31 30 30 35 30 30 31 38 34 30 31 0A 00 B4
______________________________________________________________________
(08H-09H) ID Manufacturer Name _________________________ = ACR(0AH-0BH) Product ID Code ______________________________ = 1005(0CH-0FH) Last 5 Digits of Serial Number _______________ = 00001(10H) Week of Manufacture __________________________ = 01
(11H) Year of Manufacture __________________________ = 2009(12H) EDID Version Number __________________________ = 1(13H) EDID Revision Number _________________________ = 3
(14H) VIDEO INPUT DEFINITION:Analog Signal0.700, 0.300 (1.000 Vp-p)Sync on Green, Composite Sync, Separate Syncs
(15H) Maximum Horizontal Image Size ________________ = mm(16H) Maximum Vertical Image Size __________________ = mm(17H) Display Gamma ________________________________ = 2.20
(18H) DPMS and Supported Feature(s):
Preferred Timing ModeDisplay Type = R/G/B Color
(19H-22H) CHROMA INFO:Red x - 0.647 Green x - 0.344 Blue x - 0.139 White x - 0.314Red y - 0.341 Green y - 0.587 Blue y - 0.090 White y - 0.377
(23H) ESTABLISHED TIMING I:640 x 480 @ 60Hz (IBM,VGA)640 x 480 @ 67Hz (Apple,Mac II)640 x 480 @ 72Hz (VESA)640 x 480 @ 75Hz (VESA)800 x 600 @ 56Hz (VESA)
800 x 600 @ 60Hz (VESA)
(24H) ESTABLISHED TIMING II:800 x 600 @ 72Hz (VESA)800 x 600 @ 75Hz (VESA)1024 x 768 @ 60Hz (VESA)1024 x 768 @ 70Hz (VESA)1024 x 768 @ 75Hz (VESA)1280 x 1024 @ 75Hz (VESA)
(25H) Manufacturer's Reserved Timing:1152 x 870 @ 75Hz (Apple,Mac II)
(38-53) Standard Timing Identification:Standard Timing ID 1: 640 x 480 @120HzStandard Timing ID 2: 800 x 600 @120HzStandard Timing ID 3: 1024 x 768 @120HzStandard Timing ID 4: 1280 x 1024 @60Hz
5/27/2018 Acer x1130p, x1130pa, x1230pk,x1230p,x1230pa,x1237 Projectors Sm
105/109
Standard Timing ID 5: 1280 x 720 @60HzStandard Timing ID 6: 1280 x 800 @60HzStandard Timing ID 7: 1440 x 900 @60HzStandard Timing ID 8: 1680 x 1050 @60Hz
______________________________________________________________________
(36H-47H) Detailed Timing / Descriptor Block 1:1024x768 Pixel Clock: 65.00 MHz
______________________________________________________________________Horizontal Image Size: 0 mm Vertical Image Size: 0 mmRefreshed Mode: Non-Interlaced Normal Display - No Stereo
Horizontal:Active Count: 1024 pixels Blanking Count: 320 pixelsSync Offset: 24 pixels Sync Pulse Width: 136 pixelsBorder: 0 pixels Frequency: 48.36 kHz
Vertical:Active Count: 768 lines Blanking Count: 38 linesSync Offset: 3 lines Sync Pulse Width: 6 linesBorder: 0 lines Frequency: 60.00 Hz
Digital Separate, Horizontal Polarity (-) Vertical Polarity (-)______________________________________________________________________
(48H-59H) Detailed Timing / Descriptor Block 2:
Monitor Range Limits:Min Vertical Freq - 48 HzMax Vertical Freq - 120 HzMin Horiz. Freq - 31 kHzMax Horiz. Freq - 93 kHzPixel Clock - 170 MHzGTF - Not Used
_____________________________________________________________________
(5AH-6BH) Detailed Timing / Descriptor Block 3:
Monitor Name:X1230PA
______________________________________________________________________
(6CH-7DH) Detailed Timing / Descriptor Block 4:
Monitor Serial Number:K10050018401
(7EH) Block No: No Extension EDID Block(s)
(7FH) CheckSum OK
5/27/2018 Acer x1130p, x1130pa, x1230pk,x1230p,x1230pa,x1237 Projectors Sm
106/109
X1230P EDID
EDID Block 0, Bytes 0-127 [00H-7FH]Block Type: EDID 1.3
0 1 2 3 4 5 6 7 8 9 A B C D E F________________________________________________________________
0 | 00 FF FF FF FF FF FF 00 04 72 05 11 01 00 00 0010 | 01 13 01 03 0E 00 00 78 0A D1 8A A5 57 58 96 2320 | 17 50 60 3F CF 80 31 7C 45 7C 61 7C 81 80 81 C030 | 81 00 95 00 B3 00 64 19 00 40 41 00 26 30 18 8840 | 36 00 00 00 00 00 00 18 00 00 00 FD 00 30 78 1F50 | 5D 11 00 0A 20 20 20 20 20 20 00 00 00 FC 00 5860 | 31 32 33 30 50 0A 20 20 20 20 20 20 00 00 00 FF70 | 00 4B 31 31 30 35 30 30 31 38 34 30 31 0A 00 D3
______________________________________________________________________
(08H-09H) ID Manufacturer Name _________________________ = ACR(0AH-0BH) Product ID Code ______________________________ = 1105(0CH-0FH) Last 5 Digits of Serial Number _______________ = 00001(10H) Week of Manufacture __________________________ = 01
(11H) Year of Manufacture __________________________ = 2009(12H) EDID Version Number __________________________ = 1(13H) EDID Revision Number _________________________ = 3
(14H) VIDEO INPUT DEFINITION:Analog Signal0.700, 0.300 (1.000 Vp-p)Sync on Green, Composite Sync, Separate Syncs
(15H) Maximum Horizontal Image Size ________________ = mm(16H) Maximum Vertical Image Size __________________ = mm(17H) Display Gamma ________________________________ = 2.20
(18H) DPMS and Supported Feature(s):
Preferred Timing ModeDisplay Type = R/G/B Color
(19H-22H) CHROMA INFO:Red x - 0.647 Green x - 0.344 Blue x - 0.139 White x - 0.314Red y - 0.341 Green y - 0.587 Blue y - 0.090 White y - 0.377
(23H) ESTABLISHED TIMING I:640 x 480 @ 60Hz (IBM,VGA)640 x 480 @ 67Hz (Apple,Mac II)640 x 480 @ 72Hz (VESA)640 x 480 @ 75Hz (VESA)800 x 600 @ 56Hz (VESA)
800 x 600 @ 60Hz (VESA)
(24H) ESTABLISHED TIMING II:800 x 600 @ 72Hz (VESA)800 x 600 @ 75Hz (VESA)1024 x 768 @ 60Hz (VESA)1024 x 768 @ 70Hz (VESA)1024 x 768 @ 75Hz (VESA)1280 x 1024 @ 75Hz (VESA)
(25H) Manufacturer's Reserved Timing:1152 x 870 @ 75Hz (Apple,Mac II)
(38-53) Standard Timing Identification:Standard Timing ID 1: 640 x 480 @120HzStandard Timing ID 2: 800 x 600 @120HzStandard Timing ID 3: 1024 x 768 @120HzStandard Timing ID 4: 1280 x 1024 @60Hz
5/27/2018 Acer x1130p, x1130pa, x1230pk,x1230p,x1230pa,x1237 Projectors Sm
107/109
Standard Timing ID 5: 1280 x 720 @60HzStandard Timing ID 6: 1280 x 800 @60HzStandard Timing ID 7: 1440 x 900 @60HzStandard Timing ID 8: 1680 x 1050 @60Hz
______________________________________________________________________
(36H-47H) Detailed Timing / Descriptor Block 1:1024x768 Pixel Clock: 65.00 MHz
______________________________________________________________________Horizontal Image Size: 0 mm Vertical Image Size: 0 mmRefreshed Mode: Non-Interlaced Normal Display - No Stereo
Horizontal:Active Count: 1024 pixels Blanking Count: 320 pixelsSync Offset: 24 pixels Sync Pulse Width: 136 pixelsBorder: 0 pixels Frequency: 48.36 kHz
Vertical:Active Count: 768 lines Blanking Count: 38 linesSync Offset: 3 lines Sync Pulse Width: 6 linesBorder: 0 lines Frequency: 60.00 Hz
Digital Separate, Horizontal Polarity (-) Vertical Polarity (-)______________________________________________________________________
(48H-59H) Detailed Timing / Descriptor Block 2:
Monitor Range Limits:Min Vertical Freq - 48 HzMax Vertical Freq - 120 HzMin Horiz. Freq - 31 kHzMax Horiz. Freq - 93 kHzPixel Clock - 170 MHzGTF - Not Used
______________________________________________________________________
(5AH-6BH) Detailed Timing / Descriptor Block 3:
Monitor Name:X1230P
_