+ All Categories
Home > Documents > ACSR Tech Data 01 · PDF fileAluminium strip Aluminium wire Aluminium alloy wire ACSR...

ACSR Tech Data 01 · PDF fileAluminium strip Aluminium wire Aluminium alloy wire ACSR...

Date post: 10-Mar-2018
Category:
Upload: lecong
View: 284 times
Download: 14 times
Share this document with a friend
9
Aluminium strip Aluminium wire Aluminium alloy wire ACSR Aluminium Conductor Steel Reinforced Other Aluminium products: AAC (All aluminium conductor) AAAC (All aluminium alloy conductor) AACSR (All aluminium alloy conductor steel reinforced) OPGW (Optic fiber protection overhead conductor) Solid sector shaped aluminium conductor www.m-tec.co.ca / [email protected] / +2716 450 8200
Transcript
Page 1: ACSR Tech Data 01 · PDF fileAluminium strip Aluminium wire Aluminium alloy wire ACSR Aluminium Conductor Steel Reinforced Other Aluminium products: AAC (All aluminium conductor)

Aluminium strip

Aluminium wire

Aluminium alloy wire

ACSR Aluminium Conductor Steel Reinforced

Other Aluminium products:

AAC (All aluminium conductor)

AAAC (All aluminium alloy conductor)

AACSR (All aluminium alloy conductor steel reinforced)

OPGW (Optic fiber protection overhead conductor)

Solid sector shaped aluminium conductor

www.m-tec.co.ca / [email protected] / +2716 450 8200

Page 2: ACSR Tech Data 01 · PDF fileAluminium strip Aluminium wire Aluminium alloy wire ACSR Aluminium Conductor Steel Reinforced Other Aluminium products: AAC (All aluminium conductor)

IEC

IEC

IEC

BS

BS EN

ASTM

CAN

Grade

g/cm3

Mpa

Conductivity Min.

Volume resistivity @ 20°C Ω.m

Coefficient of linier expansion per °C

Specific heat KJ/kg/K

Melt point °C

5 m

Min. % Nom. % 1.2 m

Al 99.650 99.700

Si - -

Fe 0.160 0.220

B 0.003 0.005

Other - -

Conductor continues maximum operating (°C)

Grease:

ASTM B231 (USA)

CAN/ CSA/C49 & C61089 (Canada) 1.22

0.60

890

7.154

Material properties

99.7 EC

658

Density / Specific gravity

Tensile strength (hard drawn)

Intermittent HV and

EHV voltages.

Up to 765kV an above

145

155

165

2

3

4

6

Thermal conductivity Air (W m-1 K-1)

Wind speed (m/sec)

Installation conditionsValue /

Variables

0.440

0.0264

16.04

Specifications:

IEC 61089

IEC 888

IEC 889 Velocity of Air (V) (m/hr.)

Ambient (°C)

Altitude (Katu Northern Cape)

Conductor surface absorbency (0.27-0.95)

Solar beam Intensity (W/m²) ID

Intensity of Solar sky radiation (W/m²) Id

The stated values are estimated and nominal values.

The installer should verify the actual conditions for the

specific location of installation.

30

75

BS 215 (British)

BS EN 50182 (British)

220°C

- 20°C to 80°C

Grease weight is calculated in

accordance with EN 50182 Annex B

Drop point IP 33 Min

Operating temperature

0.904

2.7

-

0.100

0.280

0.020

0.013

Chemical properties

Max. %

Last reviewed date: 16/01/2017.

# conductors SIL

per phase

Up to 132 & 220kV

Up to 440kV

100

130

1

Ground clearance (typical)

Aluminium

62.3

2.826x10-8

23x10-6

110-130

1.00058986Permittivity of air

Typical conductor configurations

The information contained within this document must not be copied, reprinted or reproduced in any form, either wholly or in part, without the written consent of M-TEC, The information is believed to be correct at the time of issue to the best of M-TEC’s

knowledge. M-TEC reserves the right to amend this specification without prior notification. This specification is not contractually valid unless specifically authorised by M-TEC. M-TEC shall not be liable for any damages whatsoever (including indirect,

incidental, special, punitive or consequential damages and loss of profits, opportunities or information) arising from or result from the use of or reliance on information contained in this document, and/or any inaccuracy or omission in such information

contained in this document.

ACSR Aluminium Conductor Steel Reinforced

A1/S1A

*Phase to phase clearance (typical)

www.m-tec.co.ca / [email protected] / +2716 450 8200

Page 3: ACSR Tech Data 01 · PDF fileAluminium strip Aluminium wire Aluminium alloy wire ACSR Aluminium Conductor Steel Reinforced Other Aluminium products: AAC (All aluminium conductor)

Aluminium conductor

Steel wire reinforcing

dia. area mass area mass dia. area mass

mm mm² kg/km mm² kg/km mm mm² kg/km

Nom. Nom. Nom. Nom. Nom. Nom. Nom. Nom.

Squirrel 1 / 2.11 2.11 3.5 27 6 / 2.11 21.0 57 6.33 24.48 84 (Z) RH ASTM

Gopher 1 / 2.36 2.36 4.4 34 6 / 2.36 26.2 71 7.08 30.62 105 (Z) RH ASTM

Weasel 1 / 2.59 2.59 5.3 41 6 / 2.59 31.6 85 7.77 36.88 127 (Z) RH ASTM

Fox 1 / 2.79 2.79 6.1 48 6 / 2.79 36.7 99 8.37 42.80 147 (Z) RH ASTM

Ferret 1 / 3.00 3.00 7.1 56 6 / 3.00 42.4 115 9.00 49.48 170 (Z) RH ASTM

Rabbit 1 / 3.35 3.35 8.8 69 6 / 3.35 52.9 143 10.05 61.70 212 (Z) RH ASTM

Mink 1 / 3.66 3.66 10.5 83 6 / 3.66 63.1 171 10.98 73.65 253 (Z) RH ASTM

Banana 1 / 3.75 3.75 11.0 87 6 / 3.75 66.3 179 11.25 77.31 266 (Z) RH ASTM

Quail 1 / 3.78 3.78 11.2 88 6 / 3.78 67.3 182 11.34 78.55 270 (Z) RH CAN

Beaver 1 / 3.99 3.99 12.5 98 6 / 3.99 75.0 203 11.97 87.53 301 (Z) RH BS EN

Racoon 1 / 4.09 4.09 13.1 103 6 / 4.09 78.8 213 12.27 91.97 316 (Z) RH BS EN

Otter 1 / 4.22 4.22 14.0 110 6 / 4.22 83.9 227 12.66 97.91 337 (Z) RH BS EN

Cat 1 / 4.50 4.50 15.9 125 6 / 4.50 95.4 258 13.50 111.33 383 (Z) RH BS EN

Hare 1 / 4.72 4.72 17.5 137 6 / 4.72 105.0 284 14.16 122.48 421 (Z) RH BS EN

Penguin 1 / 4.77 4.77 17.9 140 6 / 4.77 107.2 290 14.31 125.09 430 (Z) RH BS EN

Initial Final

*1200mm

(L)mH/km

Squirrel 50.2 80.4 8.02 0.70 1.374 1.646 1.276 0.011 1.694 130 2.87

Gopher 50.2 80.4 9.61 0.87 1.098 1.316 1.253 0.011 1.373 150 3.23

Weasel 50.2 80.4 11.45 1.05 0.912 1.092 1.234 0.011 1.159 170 3.56

Fox 50.2 80.4 13.10 1.22 0.786 0.941 1.219 0.011 1.016 190 3.86

Ferret 50.2 80.4 15.20 1.41 0.680 0.814 1.204 0.011 0.898 210 4.16

Rabbit 50.2 80.4 18.50 1.76 0.545 0.653 1.181 0.012 0.751 240 4.68

Mink 50.2 80.4 21.90 2.10 0.457 0.547 1.163 0.012 0.658 260 5.14

Banana 50.2 80.4 22.90 2.21 0.435 0.521 1.158 0.012 0.636 269 5.27

Quail 50.2 80.4 24.01 2.24 0.428 0.513 1.157 0.012 0.629 276 5.32

Beaver 50.2 80.4 25.90 2.50 0.384 0.460 1.146 0.012 0.584 290 5.63

Racoon 50.2 80.4 27.20 2.63 0.366 0.438 1.141 0.012 0.566 780 5.78

Otter 50.2 80.4 28.90 2.80 0.344 0.411 1.134 0.012 0.544 790 5.97

Cat 50.2 80.4 32.80 3.18 0.302 0.362 1.121 0.012 0.505 800 6.39

Hare 50.2 80.4 36.00 3.50 0.275 0.329 1.111 0.013 0.480 860 6.72

Penguin 50.2 80.4 37.87 3.57 0.269 0.322 1.109 0.013 0.475 920 6.80

Total Conductor

Ou

ter

laye

r

La

y d

ire

ctio

n

19.23

19.23

19.23

19.23

19.23

19.23

19.23

19.23

19.23

19.23

19.23

19.23

19.23

19.23

Steel core

Number/

Size

Co

ns

tru

cti

on

an

d d

ime

ns

ion

sP

hy

sic

al p

rop

ert

ies

Conductor

name

Conductor

name

19.23

Cu

rre

nt

ratin

g

dc

20°C

ac

75°C

Aluminium Outer layer(s)

* typical conductor centre spacing

Resistance

Ele

ctr

ica

l P

rop

ert

ies

Sp

ecific

atio

n

Sh

ort

cir

cu

it

ratin

g

kA.1sΩ/km

Number/

Size

Modulus of

Elasticity Coefficient

of linear

expansion

RTS

Grease

Nom.

(Case 2)kN/mm²

Nom. x10-6

/oC kN kg/km

Ind

ucta

nce

sin

gle

ph

ase

Imp

ed

an

ce

C

µF/km

Z

Ω/kmA

Ca

pa

cita

nce

The information contained within this document must not be copied, reprinted or reproduced in any form, either wholly or in part, without the written consent of M-TEC, The information is believed to be correct at the time of issue to the best of M-TEC’s

knowledge. M-TEC reserves the right to amend this specification without prior notification. This specification is not contractually valid unless specifically authorised by M-TEC. M-TEC shall not be liable for any damages whatsoever (including indirect,

incidental, special, punitive or consequential damages and loss of profits, opportunities or information) arising from or result from the use of or reliance on information contained in this document, and/or any inaccuracy or omission in such information

contained in this document.

ACSR (Aluminium Conductor Steel Reinforced)

(A1/S1A)

1 Steel centre wire + 6 Aluminium wires

www.m-tec.co.ca / [email protected] / +2716 450 8200

Page 4: ACSR Tech Data 01 · PDF fileAluminium strip Aluminium wire Aluminium alloy wire ACSR Aluminium Conductor Steel Reinforced Other Aluminium products: AAC (All aluminium conductor)

Aluminium conductor

Steel strand reinforcing

dia. area mass area mass dia. area mass

mm mm² kg/km mm² kg/km mm mm² kg/km

Nom. Nom. Nom. Nom. Nom. Nom. Nom. Nom.

Dog 7 / 1.57 4.79 13.6 106 6 / 4.72 105.0 284 11.01 118.54 390 (Z) RH ASTM

Leopard 7 / 1.75 5.34 16.8 132 6 / 5.28 131.4 355 12.31 148.21 487 (Z) RH ASTM

Hyena 7 / 1.97 6.02 21.3 168 7 / 4.39 106.0 286 10.75 127.29 454 (Z) RH ASTM

Initial Final

*1200mm

(L)mH/km

Dog 48.8 76.4 34.70 4.55 0.275 0.329 1.132 0.012 0.484 360 6.72

Leopard 48.8 76.4 42.20 5.68 0.219 0.263 1.154 0.012 0.448 410 7.57

Hyena 46.9 73.4 34.70 4.80 0.272 0.326 1.159 0.012 0.489 360 6.76

Aluminium Outer layer(s)

Cu

rre

nt

ratin

g

dc

20°C

* typical conductor centre spacing

Ph

ys

ica

l p

rop

ert

ies

Number/

Size

Co

ns

tru

cti

on

an

d

dim

en

sio

ns

Modulus of

Elasticity

7 Steel + 7 Aluminium

7 Steel + 6 Aluminium

Coefficient

of linear

expansion

RTS

Grease

Nom.

(Case 2)kN/mm²

Nom. A

Ele

ctr

ica

l P

rop

ert

ies

18.72

19.86

19.87

Total Conductor

Sp

ecific

atio

n

Ou

ter

laye

r

La

y d

ire

ctio

n

Resistance

Number/

Size

Steel core

ac

75°C

Ω/kmC

µF/km

Z

Ω/km

Ind

ucta

nce

sin

gle

ph

ase

Conductor

name Ca

pa

cita

nce

Imp

ed

an

ce

x10-6

/oC kN kg/km

The information contained within this document must not be copied, reprinted or reproduced in any form, either wholly or in part, without the written consent of M-TEC, The information is believed to be correct at the time of issue to the best of M-TEC’s

knowledge. M-TEC reserves the right to amend this specification without prior notification. This specification is not contractually valid unless specifically authorised by M-TEC. M-TEC shall not be liable for any damages whatsoever (including indirect,

incidental, special, punitive or consequential damages and loss of profits, opportunities or information) arising from or result from the use of or reliance on information contained in this document, and/or any inaccuracy or omission in such information

contained in this document.

Sh

ort

cir

cu

it

ratin

g

kA.1s

7 Steel + 6 Aluminium

7 Steel + 7 Aluminium

ACSR (Aluminium Conductor Steel Reinforced)

(A1/S1A)

7 Steel centre wire + 6, 7 Aluminium wires

7 Steel + 6 Aluminium

7 Steel + 7 Aluminium

Conductor

name

www.m-tec.co.ca / [email protected] / +2716 450 8200

Page 5: ACSR Tech Data 01 · PDF fileAluminium strip Aluminium wire Aluminium alloy wire ACSR Aluminium Conductor Steel Reinforced Other Aluminium products: AAC (All aluminium conductor)

Aluminium conductor

Steel wire reinforcing

dia. area mass area mass dia. area mass

mm mm² kg/km mm² kg/km mm mm² kg/km

Nom. Nom. Nom. Nom. Nom. Nom. Nom. Nom.

Dingo 1 / 3.35 10.23 8.8 69 18 / 3.35 158.7 429 16.75 167.47 498 (Z) RH ASTM

Chickadee 1 / 3.77 11.51 11.2 88 18 / 3.77 200.9 543 18.85 212.09 631 (Z) RH ASTM

Pelican 1 / 4.14 12.64 13.5 106 18 / 4.14 242.3 655 20.70 255.77 761 (Z) RH ASTM

Osprey 1 / 4.47 13.65 15.7 123 18 / 4.47 282.5 764 22.35 298.17 887 (Z) RH ASTM

Kingbird 1 / 4.78 14.60 17.9 141 18 / 4.78 323.0 873 23.90 340.96 1014 (Z) RH ASTM

Initial Final

*1200mm

(L)mH/km

Dingo 60.5 92.9 45.09 20.99 0.182 0.218 1.068 0.013 0.400 576 8.36

Chickadee 60.5 92.9 35.70 26.58 0.143 0.172 1.044 0.013 0.370 647 9.47

Pelican 60.5 92.9 53.80 32.05 0.119 0.143 1.025 0.014 0.352 646 10.45

Osprey 60.5 92.9 30.52 37.36 0.102 0.122 1.009 0.014 0.340 646 11.33

Kingbird 60.5 92.9 69.72 42.73 0.089 0.107 0.996 0.014 0.331 773 12.16

Aluminium Outer layer(s) Total Conductor

Number/

Size

Number/

Size

Steel core

Ou

ter

laye

r

La

y d

ire

ctio

n

Co

ns

tru

cti

on

an

d

dim

en

sio

ns

Conductor

name

kg/km

dc

20°C

Grease

Nom.

(Case 2)

Sp

ecific

atio

n

21.41

21.41

21.41

Ind

ucta

nce

sin

gle

ph

ase

Ca

pa

cita

nce

Imp

ed

an

ce

Cu

rre

nt

ratin

g

ac

75°C

Ω/kmC

µF/km

Z

Ω/kmA

kN/mm²

Modulus of

Elasticity Coefficient

of linear

expansion

RTS

* typical conductor centre spacing

Ph

ys

ica

l p

rop

ert

ies Conductor

name

Ele

ctr

ica

l P

rop

ert

ies

Nom. x10-6

/oC kN

21.41

21.41

The information contained within this document must not be copied, reprinted or reproduced in any form, either wholly or in part, without the written consent of M-TEC, The information is believed to be correct at the time of issue to the best of M-TEC’s

knowledge. M-TEC reserves the right to amend this specification without prior notification. This specification is not contractually valid unless specifically authorised by M-TEC. M-TEC shall not be liable for any damages whatsoever (including indirect,

incidental, special, punitive or consequential damages and loss of profits, opportunities or information) arising from or result from the use of or reliance on information contained in this document, and/or any inaccuracy or omission in such information

contained in this document.

kA.1s

Sh

ort

cir

cu

it

ratin

g

ACSR (Aluminium Conductor Steel Reinforced)

(A1/S1A)

1 Steel centre wire + 18 Aluminium wires

Resistance

www.m-tec.co.ca / [email protected] / +2716 450 8200

Page 6: ACSR Tech Data 01 · PDF fileAluminium strip Aluminium wire Aluminium alloy wire ACSR Aluminium Conductor Steel Reinforced Other Aluminium products: AAC (All aluminium conductor)

Aluminium conductor

Grease (if applicable)

dia. area mass area mass dia. area mass

mm mm² kg/km mm² kg/km mm mm² kg/km

Nom. Nom. Nom. Nom. Nom. Nom. Nom. Nom.

Petrel 7 / 2.34 7.02 30.1 238 12 / 2.34 51.6 139 11.70 81.71 377 (Z) RH ASTM

Skunk 7 / 2.59 7.77 36.9 291 12 / 2.59 63.2 171 12.95 100.10 462 (Z) RH ASTM

Leghorn 7 / 2.69 8.07 39.8 314 12 / 2.69 68.2 184 13.45 107.98 498 (Z) RH ASTM

Dotterel 7 / 3.08 9.24 52.2 412 12 / 3.08 89.4 242 15.40 141.56 653 (Z) RH ASTM

Oden 7 / 3.52 10.56 68.1 538 12 / 3.52 116.8 316 17.60 184.90 853 (Z) RH ASTM

Toucan 7 / 2.08 6.24 23.8 188 22 / 3.74 241.7 667 13.72 265.47 855 (Z) RH 10.586 ASTM

Flicker 7 / 2.39 7.17 31.4 248 24 / 3.58 241.6 653 14.33 272.99 901 (Z) RH 10.584 ASTM

Rook 7 / 2.76 8.28 41.9 331 24 / 4.14 323.1 873 16.56 364.95 1204 (Z) RH 10.577 ASTM

Dove 7 / 2.89 8.67 45.9 363 26 / 3.72 282.6 764 23.55 328.50 1126 (Z) RH 10.557 ASTM

Hawk 7 / 2.68 8.03 39.3 311 26 / 3.43 415.8 1,124 21.75 455.15 1435 (Z) RH 10.562 ASTM

Drake 7 / 3.45 10.36 65.6 518 26 / 4.44 402.9 1,089 28.13 468.51 1607 (Z) RH 10.543 ASTM

Initial Final

*1200mm

(L)mH/km

Petrel 46.1 70.8 57.52 8.60 0.522 0.682 1.141 0.012 0.771 150 4.63

Skunk 46.1 70.8 52.90 10.53 0.456 0.557 1.121 0.012 0.659 130 5.14

Leghorn 46.1 70.8 57.52 11.36 0.423 0.516 1.113 0.012 0.624 150 5.35

Dotterel 46.1 70.8 76.90 14.89 0.322 0.394 1.085 0.013 0.521 170 6.18

Oden 46.1 70.8 100.80 19.45 0.247 0.302 1.058 0.013 0.449 190 7.11

Toucan 58.8 90.4 68.90 40.14 0.119 0.146 1.106 0.012 0.377 452 10.55

Flicker 57.6 88.6 76.52 36.78 0.119 0.146 1.097 0.013 0.374 210 10.44

Rook 57.6 88.6 100.56 49.19 0.089 0.109 1.068 0.013 0.353 240 12.16

Dove 56.5 86.8 76.52 39.72 0.102 0.125 0.996 0.014 0.337 726 11.33

Hawk 58.9 90.6 57.52 18.47 0.069 0.085 1.012 0.014 0.329 610 13.89

Drake 56.5 86.8 57.52 30.98 0.072 0.087 0.960 0.015 0.314 830 13.66

19.85

15.61

15.61

15.61

15.61

19.84

19.29

19.29

20.52

Conductor

name

Ou

ter

laye

r

La

y d

ire

ctio

n

Resistance

7 Steel + 24 Aluminium

7 Steel + 26 Aluminium

Total Conductor

Number/

Size

Number/

Size

* typical conductor centre spacing

7 Steel + 22 Aluminium

7 Steel + 24 Aluminium

7 Steel + 26 Aluminium

20.44

Ph

ys

ica

l p

rop

ert

ies

Ele

ctr

ica

l P

rop

ert

ies

C

µF/km

Z

Ω/kmA

Ind

ucta

nce

sin

gle

ph

ase

Ca

pa

cita

nc

e

Imp

ed

an

ce

7 Steel + 12 Aluminium

ac

75°C

Ω/km

Cu

rre

nt

ratin

g

15.61

dc

20°C

Modulus of

Elasticity Coefficient

of linear

expansion

RTS

Grease

Nom.

(Case 2)kN/mm²

Nom. x10-6

/oC kN kg/km

7 Steel + 12 Aluminium

Steel core Aluminium Outer layer(s)

Steel strand reinforcing

7 Steel + 22 Aluminium

Co

ns

tru

cti

on

an

d d

ime

ns

ion

s

Conductor

name

Sp

ecific

atio

n

The information contained within this document must not be copied, reprinted or reproduced in any form, either wholly or in part, without the written consent of M-TEC, The information is believed to be correct at the time of issue to the best of M-TEC’s

knowledge. M-TEC reserves the right to amend this specification without prior notification. This specification is not contractually valid unless specifically authorised by M-TEC. M-TEC shall not be liable for any damages whatsoever (including indirect,

incidental, special, punitive or consequential damages and loss of profits, opportunities or information) arising from or result from the use of or reliance on information contained in this document, and/or any inaccuracy or omission in such information

contained in this document.

kA.1s

Sh

ort

cir

cu

it

ratin

g

ACSR (Aluminium Conductor Steel Reinforced)

(A1/S1A)

7 Steel centre wire + 12, 22, 24, 26, 30

Aluminium wires

7 Steel + 12 Aluminium

7 Steel + 22 Aluminium

7 Steel + 24 Aluminium

7 Steel + 26 Aluminium

www.m-tec.co.ca / [email protected] / +2716 450 8200

Page 7: ACSR Tech Data 01 · PDF fileAluminium strip Aluminium wire Aluminium alloy wire ACSR Aluminium Conductor Steel Reinforced Other Aluminium products: AAC (All aluminium conductor)

Aluminium conductor

Grease (if applicable)

dia. area mass area mass dia. area mass

mm mm² kg/km mm² kg/km mm mm² kg/km

Nom. Nom. Nom. Nom. Nom. Nom. Nom. Nom.

Tiger 7 / 2.36 7.21 30.6 240 30 / 2.36 131.2 355 16.52 161.85 595 (Z) RH BS EN

Wolf 7 / 2.59 7.91 36.9 290 30 / 2.59 158.1 427 18.13 194.94 717 (Z) RH BS EN

Lynx 7 / 2.79 8.52 42.8 336 30 / 2.79 183.4 496 19.53 226.20 832 (Z) RH CAN

Panther 7 / 3.00 9.16 49.5 389 30 / 3.00 212.1 573 21.00 261.54 962 (Z) RH BS

Bear 7 / 3.35 10.23 61.7 485 30 / 3.35 264.4 715 23.45 326.12 1199 (Z) RH BS EN

Lion 7 / 3.18 9.71 55.6 437 30 / 3.18 238.3 644 22.26 293.86 1081 (Z) RH BS EN

Goat 7 / 3.71 11.33 75.7 594 30 / 3.71 324.3 877 25.97 399.98 1471 (Z) RH BS EN

Deer 7 / 4.27 13.04 100.2 787 30 / 4.27 429.6 1,161 29.89 529.84 1949 (Z) RH BS EN

Elk 7 / 4.50 13.74 111.3 874 30 / 4.50 477.1 1,290 31.50 588.46 2164 (Z) RH BS EN

Tiger 54.3 83.4 57.87 15.98 0.220 0.268 1.512 0.009 0.546 260 7.57

Wolf 54.3 83.4 68.91 19.25 0.182 0.223 1.493 0.009 0.519 269 8.34

Lynx 54.3 83.4 79.30 22.34 0.157 0.192 1.478 0.009 0.503 276 9.03

Panther 54.3 83.4 90.80 25.83 0.136 0.166 1.463 0.009 0.489 290 9.74

Bear 54.3 83.4 109.38 32.21 0.109 0.133 1.441 0.009 0.472 780 10.94

Lion 54.3 83.4 98.98 29.02 0.121 0.148 1.451 0.009 0.479 790 10.36

Goat 54.3 83.4 133.28 39.50 0.089 0.109 1.420 0.009 0.459 800 12.19

Deer 54.3 83.4 175.42 52.33 0.067 0.082 1.391 0.009 0.445 860 14.13

Elk 54.3 83.4 198.80 58.12 0.060 0.074 1.381 0.010 0.440 920 14.93

7 Steel + 30 Aluminium

Co

ns

tru

cti

on

an

d d

ime

ns

ion

sP

hy

sic

al p

rop

ert

ies

kNx10-6

/oCNom.

18.31

18.31

18.31

kN/mm²

A

* typical conductor centre spacing

kg/km

18.31

18.31

Coefficient

of linear

expansion

RTS

18.31

18.31

Conductor

name

Grease

Nom.

(Case 2)

Ele

ctr

ica

l P

rop

ert

ies

Resistance

7 Steel + 30 Aluminium

Ω/kmC

µF/km

Z

Ω/km

18.31

18.31

Conductor

name

Steel strand reinforcing

Steel core Aluminium Outer layer(s)

Number/

Size

Number/

Size

L

mH/km

Cu

rre

nt

ratin

g

dc

20°C

ac

75°C

Total Conductor

Ou

ter

laye

r

La

y d

ire

ctio

n

Sp

ecific

atio

n

Initial Final

Modulus of

Elasticity

Single phase

Ind

ucta

nce

Ca

pa

cita

nce

Imp

ed

an

ce

The information contained within this document must not be copied, reprinted or reproduced in any form, either wholly or in part, without the written consent of M-TEC, The information is believed to be correct at the time of issue to the best of M-TEC’s

knowledge. M-TEC reserves the right to amend this specification without prior notification. This specification is not contractually valid unless specifically authorised by M-TEC. M-TEC shall not be liable for any damages whatsoever (including indirect,

incidental, special, punitive or consequential damages and loss of profits, opportunities or information) arising from or result from the use of or reliance on information contained in this document, and/or any inaccuracy or omission in such information

contained in this document.

kA.1s

Sh

ort

cir

cu

it

ra

tin

g

7 Steel + 30 Aluminium

ACSR (Aluminium Conductor Steel Reinforced)

(A1/S1A)

7 Steel centre wire + 30 Aluminium wires

www.m-tec.co.ca / [email protected] / +2716 450 8200

Page 8: ACSR Tech Data 01 · PDF fileAluminium strip Aluminium wire Aluminium alloy wire ACSR Aluminium Conductor Steel Reinforced Other Aluminium products: AAC (All aluminium conductor)

Aluminium conductor

Grease (if applicable)

dia. area mass area mass dia. area mass

mm mm² kg/km mm² kg/km mm mm² kg/km

Nom. Nom. Nom. Nom. Nom. Nom. Nom. Nom.

Zambezi 7 / 2.32 7.09 29.6 235 42 / 4.14 565.4 1,528 31.80 594.97 1764 (Z) RH BS EN

Tern 7 / 2.25 6.87 27.8 221 45 / 3.38 403.8 1,113 27.03 431.60 1335 (Z) RH ASTM

Ruddy 7 / 2.40 7.33 31.7 249 45 / 3.59 455.5 1,256 28.74 487.17 1505 (Z) RH ASTM

Rail 7 / 2.47 7.54 33.5 263 45 / 3.70 483.8 1,334 29.61 517.39 1597 (Z) RH ASTM

Bluejay 7 / 2.66 8.12 38.9 306 45 / 4.00 565.5 1,559 31.98 604.39 1865 (Z) RH ASTM

Bunting 7 / 2.76 8.43 41.9 329 45 / 4.12 599.9 1,654 33.00 641.80 1983 (Z) RH ASTM

Bersfort 7 / 3.32 10.14 60.6 476 48 / 4.27 687.4 1,895 35.58 747.96 2371 (Z) RH CAN

Peaceriver 7 / 2.25 6.87 27.8 219 48 / 2.90 317.0 874 24.15 344.88 1093 (Z) RH CAN

Initial Final

*1200mm

kN kg/km (L)mH/km

Zambezi 47.7 73.2 98.3 73 8.507 0.062 0.935 0.015 0.300 610 11.98

Tern 47.7 73.2 98.3 49 0.071 0.087 0.968 0.015 0.316 830 13.81

Ruddy 48.9 75.8 108.5 55 0.063 0.077 0.955 0.015 0.310 955 14.71

Rail 48.9 75.8 115.1 58 0.060 0.073 0.949 0.015 0.307 920 15.19

Bluejay 49.0 75.8 135.0 68 0.051 0.062 0.934 0.015 0.300 1,000 16.49

Bunting 49.0 75.8 142.2 72 0.048 0.059 0.927 0.016 0.297 1,100 17.01

Bersfort 48.4 74.9 180.0 77 0.042 0.051 0.912 0.016 0.291 1,132 18.27

Peaceriver 48.4 74.9 88.0 36 0.091 0.111 0.991 0.014 0.331 1,002 12.16

21.09

21.07

7 Steel + 42 Aluminium

7 Steel + 45 Aluminium

7 Steel + 48 Aluminium

RTS

Grease

Nom.

(Case 2)

Ph

ys

ica

l p

rop

ert

ies

Conductor

name

Nom. x10-6

/oC

7 Steel + 42 Aluminium

7 Steel + 45 Aluminium

7 Steel + 48 Aluminium

Conductor

name

Steel core

Ou

ter

laye

r

La

y d

ire

ctio

n

Sh

ort

cir

cu

it

ratin

g

kA.1s

Co

ns

tru

cti

on

an

d d

ime

ns

ion

s

Steel strand reinforcing

Aluminium Outer layer(s) Total Conductor

Sp

ecific

atio

n

Number/

Size

Number/

Size

7 Steel + 42 Aluminium

7 Steel + 45 Aluminium

7 Steel + 48 Aluminium

Modulus of

ElasticityIn

du

cta

nce

sin

gle

ph

ase

Ca

pa

cita

nce

Imp

ed

an

ce

Cu

rre

nt

ratin

g

dc

20°C

ac

75°C

Ω/kmC

µF/km

Z

Ω/km

21.08

21.49

Ele

ctr

ica

l P

rop

ert

ies

Resistance

Coefficient

of linear

expansion

kN/mm²

The information contained within this document must not be copied, reprinted or reproduced in any form, either wholly or in part, without the written consent of M-TEC, The information is believed to be correct at the time of issue to the best of M-TEC’s

knowledge. M-TEC reserves the right to amend this specification without prior notification. This specification is not contractually valid unless specifically authorised by M-TEC. M-TEC shall not be liable for any damages whatsoever (including indirect,

incidental, special, punitive or consequential damages and loss of profits, opportunities or information) arising from or result from the use of or reliance on information contained in this document, and/or any inaccuracy or omission in such information

contained in this document.

* typical conductor centre spacing

ACSR (Aluminium Conductor Steel Reinforced)

(A1/S1A)

7 Steel centre wire + 42, 45, 48 Aluminium wires

A

20.66

20.67

21.09

21.07

www.m-tec.co.ca / [email protected] / +2716 450 8200

Page 9: ACSR Tech Data 01 · PDF fileAluminium strip Aluminium wire Aluminium alloy wire ACSR Aluminium Conductor Steel Reinforced Other Aluminium products: AAC (All aluminium conductor)

Aluminium conductor

Grease (if applicable)

dia. area mass area mass dia. area mass

mm mm² kg/km mm² kg/km mm mm² kg/km

Nom. Nom. Nom. Nom. Nom. Nom. Nom. Nom.

Crow 7 / 2.92 8.92 46.9 368 54 / 4.27 773.3 2,090 34.38 820.16 2458 (Z) RH ASTM

Antelope 7 / 2.97 9.07 48.5 381 54 / 2.97 374.1 1,011 26.73 422.60 1392 (Z) RH BS

Bison 7 / 3.00 9.16 49.5 389 54 / 3.00 381.7 1,032 27.00 431.18 1420 (Z) RH BS

Zebra 7 / 3.18 9.71 55.6 437 54 / 3.18 428.9 1,159 28.62 484.48 1596 (Z) RH BS EN

Camel 7 / 3.35 10.23 61.7 485 54 / 3.35 476.0 1,287 30.15 537.66 1771 (Z) RH BS EN

Moose 7 / 3.53 10.78 68.5 538 54 / 3.53 528.5 1,428 31.77 596.99 1967 (Z) RH BS EN

Condor 7 / 3.08 9.41 52.2 410 54 / 3.08 402.3 1,088 27.72 454.49 1497 (Z) RH BS EN

Cardinal 7 / 3.38 10.32 62.8 493 54 / 3.38 484.5 1,310 30.42 547.33 1803 (Z) RH BS EN

Initial Final

*1200mm

kN kg/km (L)mH/km

Crow 46.7 73.2 113.0 77 0.037 0.046 0.918 0.016 0.292 780 19.24

Antelope 46.7 73.2 117.0 37 0.077 0.094 0.969 0.015 0.319 790 13.14

Bison 46.7 73.2 119.0 38 0.076 0.092 0.967 0.015 0.317 800 13.28

Zebra 46.7 73.2 133.0 43 0.067 0.082 0.955 0.015 0.311 860 14.12

Camel 46.7 73.2 147.0 48 0.061 0.074 0.944 0.015 0.306 920 14.91

Moose 46.7 73.2 162.0 53 0.055 0.067 0.934 0.015 0.301 980 15.75

Condor 46.7 73.2 127.9 40 0.072 0.088 0.961 0.015 0.315 889 13.65

Cardinal 46.7 73.2 149.2 49 0.059 0.073 0.942 0.015 0.305 1,022 15.05

Ph

ys

ica

l p

rop

ert

ies

Conductor

name

Ele

ctr

ica

l P

rop

ert

ies

Resistance

Nom.

19.85

7 Steel + 54 Aluminium

19.85

x10-6

/oC

19.85

21.29

19.85

19.85

19.85

19.85

7 Steel + 54 Aluminium

RTS

Grease

Nom.

(Case 2)

kN/mm²

Modulus of

Elasticity Coefficient

of linear

expansion

7 Steel + 54 Aluminium

Co

ns

tru

cti

on

an

d

dim

en

sio

ns

Conductor

name

Steel core Aluminium Outer layer(s) Total Conductor

Number/

Size

Number/

Size

Sp

ecific

atio

n

Ou

ter

laye

r

La

y d

ire

ctio

n

Steel strand reinforcing

ac

75°C

Ω/kmC

µF/km

Z

Ω/kmA

Sh

ort

cir

cu

it

ratin

g

kA.1sIn

du

cta

nce

sin

gle

ph

ase

Ca

pa

cita

nce

Imp

ed

an

ce

Cu

rre

nt

ratin

g

dc

20°C

The information contained within this document must not be copied, reprinted or reproduced in any form, either wholly or in part, without the written consent of M-TEC, The information is believed to be correct at the time of issue to the best of M-TEC’s

knowledge. M-TEC reserves the right to amend this specification without prior notification. This specification is not contractually valid unless specifically authorised by M-TEC. M-TEC shall not be liable for any damages whatsoever (including indirect,

incidental, special, punitive or consequential damages and loss of profits, opportunities or information) arising from or result from the use of or reliance on information contained in this document, and/or any inaccuracy or omission in such information

contained in this document.

* typical conductor centre spacing

ACSR (Aluminium Conductor Steel Reinforced)

(A1/S1A)

7 Steel centre wire + 54 Aluminium wires

www.m-tec.co.ca / [email protected] / +2716 450 8200


Recommended