TITAN12L1 (1050) GATE OPENING SYSTEM QUICK START INSTALLATION GUIDE 6” 11” Weld or clamp pivot arm on gate hinge post for Pull-to-Open (left) or Push-to-Open (right). Attach Actuator to Pivot Arm Attach Actuator to Gate Bracket WASHERS FIGURE 1: INSTALLATION OF ACTUATOR TO PIVOT ARM AND GATE BRACKET GATE BRACKET 912L ACTUATOR ENSURE LEVEL PIVOT ARM 6” 13” PIVOT ARM PIVOT ARM GATE GATE PIVOT ARM: Push-To-Open PIVOT ARM: Pull-To-Open ACTUATOR AND CONTROL BOX INSTALLATION: HINGE POST HINGE POST HINGE HINGE GATE BRACKET CENTERLINE GATE BRACKET CENTERLINE Pivot Arm Top of Pivot Arm TOP VIEW TOP VIEW FRONT VIEW FRONT VIEW 1/2” 1/2” Pivot Arm 1B 1A 2 4 PULL-TO-OPEN: Fully open gate, then locate bracket on gate support. PUSH-TO-OPEN: Fully close gate, then locate bracket on gate support. Pull-To-Open Push-To-Open Push-To-Open Pull-To-Open Bracket Position Bracket Position GATE OPEN Ensure actuator arm is fully retracted, then position gate bracket on gate structural support as shown below: GATE CLOSED TOP OF PIVOT ARM Affix Gate Bracket to gate struc- tural support by welding or using bolt/nut. 5 7 8 9 10 ical release open, manually push gate to desired close limit, then push to desired open limit, and then push to halfway open position. Close mechanical release, but do not lock. actuator and minimum six feet away from pivot arm (See FIG- URE 2). cable through rubber grom- mets in bottom of control box and wire per diagram at right. For dual gate, dig trench across drive and run 2nd actuator cable through con- duit. Open mechanical release on actuator. 2 3 1 6 3 CAUTION! Do NOT weld while control board is powered! 1/2”x 2-7/8” PIVOT BOLT 1/2”x3.5” BOLT LOCK NUT LOCK NUT Manually Set Limits: With actuator mechan- Mount Control Box same side as primary Wire actuator to control board: Pass Orange Orange White White Green Green Blue Blue Yellow Yellow Red Black Red Black NOTE: Dual gate: wire Motor 1 and Motor 2 the same way. EXTREMELY IMPORTANT! Read entire manual before attempting the installation. This is NOT a “do-it-yourself” project. Use a qualified con- tractor to install this system. Read all safety information! Place Battery inside control box with ter - minals facing toward the front. CAUTION! Do not mount the control box where the person using the push button on box can come in contact with the gate! 5 5 4 4 3 3 3 3 2 2 2 2 1 1 1 1 www.apollogateopeners.com | (800) 878-7829 | [email protected]
Weld or clamp pivot arm on gate hinge post for Pull-to-Open (left) or Push-to-Open (right).
Attach Actuator to Pivot Arm
Attach Actuator to Gate Bracket
WASHERS
FIGURE 1: INSTALLATION OF ACTUATOR TO PIVOT ARM AND GATE BRACKET
GATE BRACKET
912L ACTUATOR
ENSURE LEVEL
PIVOT ARM
6”
13”
PIV
OT
AR
M PIVOT ARM
GATEGATE
PIVOT ARM: Push-To-OpenPIVOT ARM: Pull-To-Open
ACTUATOR AND CONTROL BOX INSTALLATION:
HINGE POST HINGE
POST
HINGEHINGE
GATE BRACKET CENTERLINEGATE BRACKET CENTERLINE
Pivot ArmTop of Pivot Arm
TOP VIEWTOP VIEW
FRONT VIEWFRONT VIEW
1/2”1/2”
Pivot Arm
1B1A
2
4PULL-TO-OPEN: Fully open gate, then locate bracket on gate support.
PUSH-TO-OPEN: Fully close gate, then locate bracket on gate support.
Pull-To-Open
Push-To-Open
Push-To-OpenPull-To-Open
Bracket Position
Bracket Position
GATE OPEN
Ensure actuator arm is fully retracted, then position gate bracket on gate structural support as shown below:
GATE CLOSED
TOP OF PIVOT ARM
Affix Gate Bracket to gate struc-
tural support by welding
or using bolt/nut.
5
7 8
9
10ical release open, manually push gate to desired close limit, then push to desired open limit, and then push to halfway open position.
Close mechanical release, but do not lock.
actuator and minimum six feet away from pivot arm (See FIG-URE 2).
cable through rubber grom-mets in bottom of control box and wire per diagram at right.
For dual gate, dig trench across drive and run 2nd actuator cable through con-duit.
Open mechanical release on actuator.
2 31
6
3
CAUTION! Do NOT weld while control board is powered!
1/2”x 2-7/8”PIVOTBOLT1/2”x3.5”
BOLT
LOCK NUTLOCK NUT
Manually Set Limits: With actuator mechan-
Mount Control Box same side as primary
Wire actuator to control board: Pass
Ora
nge
Ora
nge
Whi
te
Whi
te
Gre
en
Gre
en
Blu
e
Blu
e
Yello
w
Yello
w
RedBlack Red Black
NOTE: Dual gate: wire Motor 1 and Motor 2 the same way.
E X T R E M E LY IMPORTANT!
Read entire manual before attempting the installation. This is NOT a “do-it-yourself” project. Use a qualified con-tractor to install this system. Read all safety information!
Place Battery inside control box with ter-
minals facing toward the front.
CAUTION! Do not mount the control box where the person using the push button on box can come in contact with the gate!
Actuator CableBlueBUS WiringLoop WiringSolar Panel WiringAC Power Wiring
6 foot min. from pivot
install
Conduit for BlueBUS and actuator cable
BlueBUS Photo Eye
Open Limit Safety
Loop
Open Limit
Close Limit
816
9
10
34
5
15
11 11
12
1
7
7
7
26
FIGURE 2: TYPICAL TITAN GATE SYSTEM (PULL-TO-OPEN, DUAL-GATE SHOWN)
OPEN
MOTOR 2 Limit LED (Red/Green)MOTOR 1 Limit LED (Red/Green)
MOTOR 1 Inputs ButtonOXI/A RX
Green LED
Solar Panel
12VDC Battery
DO NOT USEPOWER INPUTS
12-32VDC PowerSupply (Optional)
MOTOR 2 Inputs
STOP
CLOSE
UPOKDOWN
Exi
tE
dg
e
Ent
rap
Shad
ow
Safe
ty
OXI/A Plugin Radio Receiver
DISPLAYFORCE
RESET
Display
SPEEDSafety Device Conn.
AudioAlarm
BlueBUS Connector+
FUNCTIONSDELAY
FUNCTION1. Learn
LEARNSwing
FUNCTIONSButton
PRESS
OK
OK OK
LightHeavy Average
Enter
LEARNSlide
UP Use UP/DOWN buttons to
select “Average”
BLINKING = Learn Mode
GATE LIMIT LEARN PROCEDURE:
1. Test Gate Conditions: Remove pivot bolt(s) and move gateto open/close positions. Check for free travel without bind-ing, then reconnect actuator(s) to gate.
2. Connect power: See INSTRUCTION 13, above.
3. Enter Learn Mode: See FIGURE 4. NOTE: With “ENTER”flashing, “OPEN” and “CLOSE” buttons must be helddown to operate. Complete Step 4 for each actuator/gateindividually (disconnect actuator NOT being adjusted). Re-connect both actuators prior to Step 5.
4. Adjust Limit Location: a) Hold down “OPEN” button untildesired open position reached. If motion is opposite thandesired, switch RED and BLACK wires at motor input. b)Adjust open limit until Limit LED glows GREEN. If illumi-nated RED, switch ORANGE & WHITEWHITE wires at terminalblock. c) Hold down “CLOSE” button until desired closeposition. d) Adjust close limit until Motor Limit LED illumi-nates RED. e) Hold down “OPEN” until gate at middle oftravel. If dual gate, connect both actuator cables to board.
5. Commence Limit Learn: In Learn Mode (with “ENTER” stillflashing) press “OK” and the following events will occur:a) Partial open. b) Slow travel in close direction. c) Slowtravel in open direction. d) Full speed in close direction.
Basic limit programming is complete. See the manual for ad-ditional programming.
11
12
13 16
15
14Install, and connect to con-trol board, 100 feet max. See 1050 diagram below.
al power supply, and/or solar panels to board. See 1050 dia-gram below. Run AC power to AC-DC power supply, but do NOT connect AC power direct-ly to control board!
hold OXI/A RX button until green LED lights solid, then release. b) Within 10 seconds, press/hold any key on Nice TX until green LED blinks 3 times. c) Wait 15 sec. then press TXbuttons to verify operation.
accessories, such as safety loops, strobes, photo eyes, or other safety devices. See FIGURE 3 below.
