Addendum 2 REVISED BID DUE DATE: Wednesday, February 19 ... · g) DRAWING M202: Remove sheet M202...

10435 Downsville Pike Hagerstown MD 21740

301-766-2800

Addendum 2 Bid #2020-16

February 6, 2020

Addendum 2

TO: All Prospective Offerors

FROM: Scott Bachtell, Supervisor of Purchasing

REF: Bid #2020 -16 Renovations for New Programs at Washington County Technical High School

REVISED BID DUE DATE: Wednesday, February 19, 2020 at 11:00 am EST

Please note the following changes/clarifications to Bid #2020-16:

Receipt of this Addendum is to be acknowledged, in the space provided in the Revised Bid Form. Failure to do so may

subject the Bid to be considered as non-responsive. This Addendum forms a part of the Contract Documents.

A. GENERAL

1. CLARIFICATIONS: a) The Bid Due Date has been revised from Friday February 4, 2020 at 11:00 a.m. EST to

Wednesday February 19, 2020 at 11:00 a.m. EST. All other bid day submission requirements remain the same.

2. CONTRACTORS QUESTIONS:

a) Question: Can the bid date be pushed back a few days due to Addendum #1? Response: Refer to a) in the Clarifications, Revised Bid Due Date is Wednesday February

19, 2020 at 11:00 a.m.

b) Question: I do not see a hardware schedule in the specs, please advise. Please advise if door #201 is going into aluminum storefront system, if so I need hardware set.

Response: Refer to Addendum #1 dated February 3, 2020.

b) Question: Do doors 103, 202, & 208 get aluminum frames, once again if so I need hardware set. Also if you look at details on A401 some details are showing center set & some are showing front set. Response: Refer to Addendum #1 dated February 3, 2020.

c) Question: Missing the panel schedule and details for Panel LHA on the drawings. Need that info for pricing. Response: Panel schedules and information are shown on Drawing E602 as provided in Addendum #1 dated February 3, 2020.


301-766-2800


d) Question: Missing the existing panel schedule and details of the MDP. Need this info to price breakers to match. Response: Refer to revised Drawing E601 in this Addendum #2. Power distribution was revised to include a new transformer fed from a new single circuit breaker in the MDP. The transformer will extend power to each of the new Panels. In addition to the provided panel manufacturer information on Drawing E601, the model number of Panel MDP is HCR5488162U with ratings of 1200A, 480V, 3-Phase & 4-Wire.

e) Question: Missing the existing panel schedules and details for Panels HA-1 and HA-2. Need this to info for pricing breakers to match. Response: Refer to Addendum #1 dated February 3, 2020. Panel schedules and information are shown on Drawing E602.

f) Question: We will need the existing Fire Alarm device types and a POC for pricing the fire alarm work. Existing facility I’m sure they have a preferred sub to use. Response: The existing Fire Alarm System is Simplex. Refer to Addendum #1 dated February 3, 2020 for specified requirements.

g) Question: There are no details on the power poles needed per drawing E302. We will need the details to get pricing. Response: Refer to revised Drawing E302 in this Addendum #2.

h) Question: Based on the drawings it appears that VAV2 is a panel? There are several VAV’s to be fed from VAV2 but it is not shown anywhere in the drawings. Need the details on this panel to know the distance needed for circuitry and what breakers we will need to match. Response: Panel VAV-2: Manufacturer – Square D. Electrical Ratings – 400A with 400A (MCB), 277/480V, 3-Phase, 4-Wire. Panel is shown on E303.

i) Question: Panel schedule LN1 shows circuits (9,11,13)(10,12,14)(15,17,19) to feed equipment in room 204. There is nothing shown for this equipment as far as location. We need those details for pricing. Response: Equipment and cord reel are mislabeled on E302 as being fed from Panel LN. These are to be fed from Panel LN1. Refer to revised E302 in this addendum.

j) Question: Drawing E304 shows a new transformer and panel that we have no feeder information for. We will need that for pricing. Response: Refer to Addendum #1 dated February 3, 2020. Transformer and panel feeders are shown on Drawing E602.


301-766-2800


k) Question: Looking for more information or at least detail information on the stub wall in the classrooms. Will there be floor cutting to route conduits for communication, power, etc.. Also could you look into the wage rates on this job, or send me information on the wages. Could we also receive more information on the specs for the cord reels? Response: There is a raised floor for the lab areas and server room. There is also a stub wall and power pole for the classroom, as such there should be no need for floor cutting to run power or data circuits in these areas. Refer to Note 5 on Drawing E302 in this Addendum #2 for cord reel manufacturer and coordinate color with owner. With regards to wage rates, they are not required for this project, please refer to specifications for all bidding requirements.

l) Question: Details 2 and 3 do not adequately show where “switch A/B” is located or if “Switch A/B” is actually “switch A” and “switch B”. Detail 2 calls for (4) data’s to be installed from “switch A/B” to WCPS Rack in server room, there are (2) WCPS racks in the server room. Does this require (4) data’s to each WCPS Rack from each student rack? (4) data’s from each triangle to each WCPS rack? (4) data’s from wherever “switch A/B:” is located to (1) of the 2 WCPS racks? The same questions apply to Detail 3 with the teacher connections. Response: Refer to revised E301 in this Addendum #2 for clarification. Four (4) data cables shall extend from the patch location on one of the two WCPS Racks to a four (4) port wall plate at each student/teacher location. There is not a switch required at each of the student/teacher locations. The data should terminate at each student/teacher location with the four (4) port wall plate. Coordinate patch rack configuration with WCPS prior to termination of cabling.

m) Question: On Drawing ID001 it shows floor finishes of ACFL-1/RF-1 for Rooms 101 and 106, but I can’t seem to figure out which portions of these rooms receive the ACFL and which portions receive the RF. Response: There is a small area of resilient flooring just inside the corridor doors, before the ramps and the raised floor. That’s what the RF-1 is.

3. CHANGES TO DRAWINGS:

a) DRAWING E301: Remove sheet E301 dated January 31, 2020 Addendum #1 in its entirety and replace with attached sheet E301 dated “February 06 Addendum #2”. i. Revised details to indicate that the cabling from each of the student/teacher locations

will be from one of the WCPS Patch Racks to a 4-port data wall plate at each “workstation”.

ii. Revised sheet to include UPS power outlet at one of the WCPS Racks. iii. Revised sheet to indicate requirement of Fiber to be extended from WCPS Racks to MDF

Room on floor above.


301-766-2800


b) DRAWING E302: Remove sheet E302 dated January 31, 2020 Addendum #1 in its entirety and replace with attached sheet E302 dated “February 06 Addendum #2”.

i. Revised sheet to correct three circuit designations to indicated to be provided power

from Panel LN1. ii. Revised sheet to add basis of design manufacturer and model of Power Poles to Number

Note 10. And added schematic detail for power pole.

c) DRAWING E304: Remove sheet E304 dated January 31, 2020 Addendum #1 in its entirety and replace with attached sheet E304 dated “February 06 Addendum #2”.

i. Revised power distribution to new Panels (LN1, LJ1, LJ2) to extend power via New

transformer on Mezzanine. ii. Power for transformer to be fed from a new breaker in MDP on Mezzanine via wire

trough and disconnect switches.

d) DRAWING E305: Remove sheet E305 dated January 31, 2020 Addendum #1 in its entirety and replace with attached sheet E305 dated “February 06 Addendum #2”.

i. Location of Air-Cooled Condensing Units associated with CRAC Units revised to be

located on the Lower Level roof.

e) DRAWING E601: Remove sheet E601 dated January 31, 2020 Addendum #1 in its entirety and replace with attached sheet E601 dated “February 06 Addendum #2”.

i. Revised power distribution to new Panels (LN1, LJ1, LJ2) to be provided via New

transformer on Mezzanine. ii. Power for transformer to be fed from a new breaker in MDP on Mezzanine via wire

trough and disconnect switches. iii. Revised Panel LN Schedule to make incorrect designated circuits spares. iv. Revised Panel LJ2 Schedule to add UPS and removed kVA load entries on spared circuits.

f) DRAWING M201: Remove sheet M201 dated January 17, 2020 in its entirety and replace with attached sheet M201 dated “February 06 Addendum #2”.

i. Rerouted piping between CRAC Units and Air -Cooled Condensing Units to

accommodate new location of outdoor units on Lower Level Roof.

g) DRAWING M202: Remove sheet M202 dated January 17, 2020 in its entirety and replace with attached sheet M202 dated “February 06 Addendum #2”.

i. Rerouted piping between CRAC Units and Air-Cooled Condensing Units to accommodate

new location of outdoor units on Lower Level Roof.


301-766-2800


h) DRAWING M203: Remove sheet M203 dated January 17, 2020 in its entirety and replace with attached sheet M203 dated “February 06 Addendum #2”.

i. Location of Air-Cooled Condensing Units associated with CRAC Units revised to be

located on the Lower Level roof.

4. ATTACHMENTS

Drawings ( 8 pages) E301, E302, E304, E305, E601, M201, M202, M203

END OF ADDENDUM 2

Addendum #2 Drawings (8 pages)

Drawing # Drawing Date E 301 Revised 2/6/2020 E 302 Revised 2/6/2020 E 304 Revised 2/6/2020 E 305 Revised 2/6/2020 E 601 Revised 2/6/2020 M201 Revised 2/6/2020 M202 Revised 2/6/2020 M203 Revised 2/6/2020

UPUP

PRN

PRN

PRN

PRN

PRN

PRN

PRN

PRN

XR

XR

PANEL LJ (XR)

+60"

+60"

+60"

+60"

+60"

+60"

+60"

+60"

LJ1-1 LJ1-2 LJ1-3 LJ1-4

LJ1-17

LJ1-18

LJ1-26

LJ1-9

LJ1-25

LJ1-27

LJ1-16

LJ1-11

LJ1-12

LJ1-13

LJ1-14

LJ1-21

LJ1-22

LJ1-23

LJ1-24

LJ1-20

LJ1-5 LJ1-6 LJ1-7 LJ1-8

LJ1-32 LJ1-33

LJ1-34

LJ1-35

LJ1-28 LJ1-29 LJ1-30

LJ1-31

PANEL LJ1

LJ1-38

CLASSROOM105

AI / CLOUDCOMPUTING

LAB106

CISCO / CRANLAB101

CLASSROOM102

SERVERROOM

104

WORK AREA103

+60"

+60"

+60"

+60"

+60"

LJ1-36

LJ1-37

LJ1-39

4

(TYP)

5

(TYP)

6

(TYP)

3

(TYP)

LJ1-10

1

(TYP)

PANEL LJ2

(SECTIONS 1 & 2)

3(TYP)

1

(TYP)

16

16(TYP)

2

(TYP)

EX. IDF ROOM207

EX. TELECOMROOM178

VMS

13

12

12

VMS

13

AVP

14

14

AVP

+60"

+60"

+60"

LJ1-19

LJ2-1

LJ2-3

LJ2-5

LJ2-7

LJ2-9

LJ2-11

LJ2-13

LJ2-15

LJ2-2

LJ2-4

LJ2-6

LJ2-8

LJ2-10

LJ2-12

LJ2-14

LJ2-16

LJ2-23

LJ2-25

LJ2-27

LJ2-29

LJ2-31

LJ2-33

LJ2-24

LJ2-26

LJ2-28

LJ2-30

LJ2-32

LJ2-34

LJ2-35

LJ2-36

LJ2-17

LJ2-18

LJ2-19

LJ2-20

LJ2-21

LJ2-22

LJ1-48

9

(TYP)

9

(TYP)

9

(TYP)

10

(TYP)

11

15

(TYP)

10

(TYP)

9

(TYP)

9

(TYP)

17

17

17

18

18

18

LJ2-37

8

19

© COPYRIGHT 2020 NOELKER AND HULL ASSOCIATES, INC

ISSUE DATE:

SCALE:

SHEET INFORMATION

M/E/P ENGINEER

STRUCTURAL ENGINEER

CIVIL ENGINEER

LANDSCAPE ARCHITECT

PROJECT ADDRESS

PROJECT OWNER

PROJECT STATUS

PROJECT INFORMATION

REVISIONS

PROJECT TEAM

ARCHITECT

JOB NUMBER:

SHEET TITLE:

SHEET NUMBER:

PROJECT TITLE

30 WEST KING STREETCHAMBERSBURG, PA | 17201-1540P: 717.263.8464 | F: 717.263.6031

NOELKERHULL.COMPA | MD | VA

TECH HIGHPROGRAMS

50 WEST OAK RIDGE DRIVEHAGERSTOWN, MD 21740

100% CD'S

01-17-2020PROJ. #19-0476

WASHINGTON COUNTYPUBLIC SCHOOLS

REV. #: DESCRIPTION: DATE:

Professional Certification. I

hereby certify that these

documents were prepared or

approved by me, and that I

am a duly licensed

professional engineer under

the laws of the State of

Maryland. License No:45511

Expiration Date: 06/03/2020

CJL ENGINEERING

TRUE NORTH

PLANNORTH

KEY PLAN

EXISTING

PROGRAM 1 PROGRAM2

5285 WESTVIEW DR., SUITE 203 | FREDERICK MD, 21703P: 301.695.9424 | F: 301.293.6338

CJL Project #19-0476

1 ADDENDUM #1 01-31-202 ADDENDUM #2 02-06-20

E301

PART FIRST FLOOR PLAN - NEW WORK -POWER & COMMUNICATION

1/4" = 1'-0"

E301

1

PART FIRST FLOOR PLAN - NEW WORK - POWER & COMMUNICATION

NUMBERED NOTES:

CONTRACTOR SHALL INSTALLED LOCATION OF POWER AND DATA, IN THE LABS, ON STUB WALL WITH ARCHITECT AND OWNER PRIOR TO

INSTALLATION. CIRCUITS SHALL BE INSTALLED AT NEAREST WALL TO THE EQUIPMENT THEY SUPPLY.

DEVICES SHALL BE INSTALLED ABOVE LOWER CABINETS. CONTRACTOR SHALL COORDINATE INSTALLATION WITH OWNER PRIOR TO

INSTALLING.

CONTRACTOR SHALL PROVIDE AND WIRE DATA CONNECTION FOR STUDENTS IN THE LABS. FOUR-PORT WALL PLATE AND DATA QUICK

CONNECTS SHALL BE INSTALLED AT EACH POINT OF CONNECTION AS SHOWN. REFER TO DETAIL 2 OF THIS DRAWING. CONTRACTOR SHALL

ALSO CLEARLY LABEL SOURCE AND DESTINATION OF EACH DATA LINE.

COORDINATE ACTUAL LOCATION AND HEIGHTS WITH OWNER PRIOR TO INSTALLING DEVICES FOR TV MONITOR.

PROVIDE 12X12X6 JUNCTION BOX FLUSH MOUNTED IN WALL AND INSTALL 1" CONDUITS INDICATED.

PROVIDE INFLOOR BOX BY HUBBELL OR APPROVED EQUAL. PROVIDE ALL THE REQUIRED MATERIALS FOR A COMPLETE INSTALLATION.

CIRCUITS SHALL BE INSTALLED ON NEAREST INTERIOR STUB WALL.

POWER STRIP, CONTRACTOR SHALL INSTALL ON RACK.

CONTRACTOR TO INSTALL NEMA L5-30R RECEPTACLE TO POWER THE UPS. CO-ORDINATE ACTUAL LOCATION OF RECEPTACLE WITH

LOCATION OF UPS.

STUDENT RACKS. FOR EACH RACK, CONTRACTOR SHALL PROVIDE ITEMS LISTED BELOW. ALSO REFER TO DETAIL 2 ON DRAWING E701 FOR

A TYPICAL STUDENT RACK DETAIL.

1. 1 TWO POST RACK WITH 5" VERTICAL FRONT AND REAR CABLE MANAGEMENT, STUDENT RACKS, WITH MODEL NUMBER

GLRR-1984BA-5FR OR EQUAL.

2. 3 STATIONARY SHELVES, STUDENT RACK, WITH MODEL NUMBER 7206-EIA.

3. 3 POWER STRIP FOR STUDENT EQUIPMENT WITH MODEL NUMBER 7219 OR EQUAL.

TEACHER RACKS. FOR EACH OF THE 2 RACKS, CONTRACTOR SHALL PROVIDE ITEMS LISTED BELOW. ALSO REFER TO DETAIL 3 ON DRAWING

E701 FOR A TYPICAL TEACHER RACK DETAIL.

1. 1 FOUR POST RACK WITH M6 MOUNTING AND 5" VERTICAL FRONT AND REAR CABLE MANAGEMENT WITH MODEL NUMBER 4PM6-29-5FR

OR EQUAL.

2. 1 POWER STRIP WITH MODEL NUMBER 7219 OR EQUAL.

WCPS RACK, CONTRACTOR SHALL PROVIDE THE FOLLOWINGS FOR THIS RACK:

1. 1 RACK ENCLOSURE WITH MOUNTING RAILS AND CABLE MANAGEMENT, WITH MODEL NUMBER GL840ENT-4048SSS OR EQUAL.

2. 4 DISCRETE DISTRIBUTION MODULE PANEL, PATCH PANEL FOR WCPS RACK, WITH MODEL NUMBER CPP-UDDM-SL-2U-48.

3. 1 HIGH DENSITY MODULAR CASSETTE SLIDING PANEL, FIBER TRAY FOR WCPS RACK, WITH MODEL NUMBER HD-1U OR EQUAL.


CONTRACTOR SHALL PROVIDE AUDIO VISUAL PLATE (AVP) WITH MINIMUM OF TWO HDMI INPUT AND ONE ETHERNET. CONTRACTOR SHALL

ALSO PROVIDE ASSOCIATED 4K HDMI CABLE FOR A COMPLETE SYSTEM.

CONTRACTOR SHALL PROVIDE TWO VIDEO MATRIX SWITCHER (VMS) -1 FOR EACH TEACHER WORKSTATION, WITH 4 HDMI SOURCES TO 4

DISPLAYS, REFER TO DETAIL 4 FOR CONNECTION RISER DETAIL. ATEN MODEL VM0404HA SHALL BE USED AS A BASIS OF DESIGN FOR THE

VMS.

CONTRACTOR SHALL PROVIDE CABINET FOR EACH VIDEO MATRIX SWITCHER. STARTECH RK619WALL CABINET SHALL USED AS A BASIS OF

DESIGN FOR THE CABINET.

WCPS RACK, CONTRACTOR SHALL PROVIDE THE FOLLOWINGS FOR THIS RACK:

1. 1 RACK ENCLOSURE WITH MOUNTING RAILS AND CABLE MANAGEMENT, WITH MODEL NUMBER GL840ENT-4048SSS OR EQUAL.

2. 4 DISCRETE DISTRIBUTION MODULE PANEL, PATCH PANEL FOR WCPS RACK, WITH MODEL NUMBER CPP-UDDM-SL-2U-48.


CONTRACTOR SHALL PROVIDE AND WIRE DATA CONNECTION FOR TEACHERS IN THE LABS. FOUR-PORT WALL PLATE AND DATA QUICK

CONNECTS SHALL BE INSTALLED AT EACH POINT OF CONNECTION AS SHOWN. REFER TO DETAIL 3 OF THIS DRAWING. CONTRACTOR SHALL

ALSO CLEARLY LABEL SOURCE AND DESTINATION OF EACH DATA LINE.

CONTRACTOR SHALL INSTALL QUAD RECEPTACLE FOR RACK POWER STRIP IN THE SUB-FLOOR IN THE PROXIMITY OF THE RACK IT IS

SUPPLYING. COORDINATE EXACT LOCATION WITH THE ARCHITECT AND OWNER.

CONTRACTOR SHALL COORDINATE ACTUAL LOCATION OF SPEAKERS WITH OWNER.

CONTRACTOR SHALL PROVIDE FIBER CABLE FROM WCPS RACK TO THE MDF ROOM ON THE MAIN FLOOR.

1

2

3

4

5

6

7

8

DATA LINE 1

DATA LINE 2

DATA LINE 3

DATA LINE 4

DATA TO PATCH PANEL

IN WCPS RACK IN

SERVER ROOM

1/4" = 1'-0"

E301

2

LAB DATA SWITCH CONNECTION FOR STUDENTS

9

10

11

12

13

14

15

DATA LINE 1

DATA LINE 2

DATA LINE 3

DATA LINE 4

FOUR-PORT

DATA

WALL-PLATE

1/4" = 1'-0"

E301

3

LAB DATA CONNECTION FOR TEACHERS

16

1/4" = 1'-0"

E301

4

LAB AUDIO-VISUAL MATRIX RISER

INPUT

OUTPUT

4X4 VIDEO MATRIX SWITCHER (VMS)

AVP

TV

(TYP. OF 4)

HDMI 1

HDMI FOR TV / MONITOR (TYP. OF 4)

HDMI 2

ETHERNET

GENERAL NOTES:

1. CONTRACTOR SHALL ROUTE ALL DATA CABLES IN THIS AREA TO THE SERVER ROOM.

17

18

2

19

2

DATA TO PATCH PANEL

IN WCPS RACK IN

SERVER ROOM

2

2

2

2

2

FOUR-PORT

DATA

WALL-PLATE

ON

KNEE-WALL

AutoCAD SHX Text

DD

AutoCAD SHX Text

DD

AutoCAD SHX Text

DD

AutoCAD SHX Text

DD

AutoCAD SHX Text

DD

AutoCAD SHX Text

DD

AutoCAD SHX Text

DD

AutoCAD SHX Text

DD

AutoCAD SHX Text

DD

AutoCAD SHX Text

DD

AutoCAD SHX Text

DD

AutoCAD SHX Text

DD

AutoCAD SHX Text

DD

AutoCAD SHX Text

DD

AutoCAD SHX Text

DD

AutoCAD SHX Text

DD

AutoCAD SHX Text

DD

AutoCAD SHX Text

DD

AutoCAD SHX Text

DD

AutoCAD SHX Text

DD

AutoCAD SHX Text

DD

AutoCAD SHX Text

DD

AutoCAD SHX Text

DD

AutoCAD SHX Text

DD

AutoCAD SHX Text

DD

AutoCAD SHX Text

DD

AutoCAD SHX Text

DD

AutoCAD SHX Text

DD

AutoCAD SHX Text

J

AutoCAD SHX Text

J

AutoCAD SHX Text

DD

AutoCAD SHX Text

DD

AutoCAD SHX Text

DD

AutoCAD SHX Text

DD

AutoCAD SHX Text

DD

AutoCAD SHX Text

DD

AutoCAD SHX Text

DD

AutoCAD SHX Text

DD

AutoCAD SHX Text

DD

AutoCAD SHX Text

DD

AutoCAD SHX Text

DD

AutoCAD SHX Text

DD

AutoCAD SHX Text

DD

AutoCAD SHX Text

DD

AutoCAD SHX Text

DD

AutoCAD SHX Text

DD

AutoCAD SHX Text

DD

AutoCAD SHX Text

DD

AutoCAD SHX Text

DD

AutoCAD SHX Text

DD

AutoCAD SHX Text

DD

AutoCAD SHX Text

DD

AutoCAD SHX Text

DD

AutoCAD SHX Text

DD

AutoCAD SHX Text

DD

AutoCAD SHX Text

DD

AutoCAD SHX Text

TV

AutoCAD SHX Text

TV

AutoCAD SHX Text

TV

AutoCAD SHX Text

TV

AutoCAD SHX Text

TV

AutoCAD SHX Text

TV

AutoCAD SHX Text

TV

AutoCAD SHX Text

TV

AutoCAD SHX Text

DD

AutoCAD SHX Text

DD

AutoCAD SHX Text

DD

AutoCAD SHX Text

DD

AutoCAD SHX Text

DD

AutoCAD SHX Text

DD

AutoCAD SHX Text

DD

AutoCAD SHX Text

DD

AutoCAD SHX Text

DD

AutoCAD SHX Text

DD

AutoCAD SHX Text

DD

AutoCAD SHX Text

DD

AutoCAD SHX Text

DD

AutoCAD SHX Text

DD

AutoCAD SHX Text

DD

AutoCAD SHX Text

DD

AutoCAD SHX Text

DD

AutoCAD SHX Text

DD

AutoCAD SHX Text

DD

AutoCAD SHX Text

DD

AutoCAD SHX Text

DD

AutoCAD SHX Text

DD

AutoCAD SHX Text

DD

AutoCAD SHX Text

DD

AutoCAD SHX Text

DD

AutoCAD SHX Text

DD

AutoCAD SHX Text

DD

AutoCAD SHX Text

DD

AutoCAD SHX Text

DD

AutoCAD SHX Text

DD

AutoCAD SHX Text

DD

AutoCAD SHX Text

DD

AutoCAD SHX Text

DD

AutoCAD SHX Text

DD

AutoCAD SHX Text

DD

AutoCAD SHX Text

DD

AutoCAD SHX Text

SS

AutoCAD SHX Text

SS

AutoCAD SHX Text

SS

AutoCAD SHX Text

W

AutoCAD SHX Text

W

AutoCAD SHX Text

W

A

B

C

D

PRN

PRN

PRN PRN

PRN

PRN

PRN

PRN

PRN

PRN

PRN

PANEL LM (XR)

PANEL LN (XR)

+60"

+60" +60"

+60"

LN-2

LN-4 LN-6

LN-7

LN-8 LN-9

LN-10 LN-11

LN-12

LN-14

LN-16

+60"

+60"

+60"

SAW

CORD REEL (TYP)

IRON

WORKER

PRESS

WELDER

LN-1

LN-3

LN-5LN-13

LN-15

LN-17

HA SECT.2 - 40

LN1-3

LN1-1 LN1-2

LHA-7,9

LHA-11,13

LN1-5

LN1-6

LN-20

LHA-2,4,6

LHA-8,10,12

PANEL LN1

LHA-1,3,5

LHA-15,17

10

3(TYP)

4

(TYP)

5

6

7

8

QA / QC205

STORAGE202

WELDING206

TRAININGUNIT SPACE

204

MACHINETECH SPACE

203

CLASSROOM201

EMERGENCY POWER OFF

FOR PANEL LN1

LN-19

9

LN1-9,11,13

LN1-15,17,19 LN1-10,12,14

8

8

8

8

8

8

8 8

TBTP

MILL

TBTP

MILL

TBTP

LATHE

TBTP

LATHE

TBTP CNC LATHETBTP CNC LATHE

TBTP CNC

MILL

TBTP CNC

MILL

DRILL

PRESS

1

(TYP)

10

2

(TYP)

2

VMS

12

11

LN-28

14

(TYP)

LN-30

LN-32

LN-33

14

(TYP)

LN-35

LN-37

LN-34

LN-36

LN-38

14

(TYP)

13

AVP

+60"

+60"+60"

15

15

15

9876


ISSUE DATE:

SCALE:

SHEET INFORMATION

M/E/P ENGINEER

STRUCTURAL ENGINEER

CIVIL ENGINEER

LANDSCAPE ARCHITECT

PROJECT ADDRESS

PROJECT OWNER

PROJECT STATUS

PROJECT INFORMATION

REVISIONS

PROJECT TEAM

ARCHITECT

JOB NUMBER:

SHEET TITLE:

SHEET NUMBER:

PROJECT TITLE



TECH HIGHPROGRAMS


100% CD'S

01-17-2020PROJ. #19-0476







am a duly licensed





CJL ENGINEERING

TRUE NORTH

PLANNORTH

KEY PLAN

EXISTING

PROGRAM 1 PROGRAM2




E302

PART FIRST FLOOR PLAN - NEW WORK -POWER & COMMUNICATION

1/4" = 1'-0"

E302

1

PART FIRST FLOOR PLAN - NEW WORK - POWER & COMMUNICATION

NUMBERED NOTES:

CONTRACTOR SHALL INSTALL POWER AND DATA, IN THE CLASSROOM, ON STUB WALL. ACTUAL LOCATION

OF EQUIPMENT SHALL BE CO-ORDINATED WITH ARCHITECT AND OWNER PRIOR TO INSTALLATION.

CIRCUITS SHALL BE INSTALLED AT NEAREST WALL TO THE EQUIPMENT THEY SUPPLY.

CONTRACTOR SHALL HARDWIRE DATA CONNECTION FOR STUDENTS AND TEACHER TO THE IDF ROOM.

CONTRACTOR SHALL ALSO CLEARLY LABEL SOURCE AND DESTINATION OF EACH DATA LINE.

COORDINATE ACTUAL LOCATION AND HEIGHTS WITH OWNER PRIOR TO INSTALLING DEVICES FOR TV

MONITOR.

PROVIDE 12X12X6 JUNCTION BOX FLUSH MOUNTED IN WALL AND INSTALL 1" CONDUITS INDICATED.

PROVIDE HUBBELL OR APPROVED EQUAL CORD REEL WITH RECEPTACLE AS INDICATED FOR 120V, ALL 3

PHASE RECEPTACLES SHALL BE COORDINATED WITH MANUFACTURERS EQUIPMENT. REELS SHALL BE

INSTALLED ON GRID WORK, COORDINATE WITH G.C. PRIOR TO INSTALLING.

HEAVY DUTY, 240V, 2 POLE, 100A, NEMA 12, NON-FUSED DISCONNECT

3 #3 & 1 #8 EGC IN 1 1/4"C

3 #12 & 1 #12 EGC IN 3/4"C

PRESS IS HYDRAULICALLY OPERATED FROM THE IRON WORKER, NO SEPARATE POWER IS REQUIRED.

POWER POLE FOR ROUTING POWER REQUIRED SEPARATION SHALL BE MAINTAINED BETWEEN POWER

AND DATA CABLES. WIREMOLD MODEL: 30TC-4V OR APPROVED EQUAL FOR THE POWER POLE. HEIGHT OF

POLE SHALL BE FIELD VERIFIED. COORDINATE COLOR AND FINISH WITH ARCHITECT AND OWNER.

CONTRACTOR SHALL PROVIDE AUDIO VISUAL WALL PLATE WITH MINIMUM OF TWO HDMI INPUT AND ONE

ETHERNET. CONTRACTOR SHALL ALSO PROVIDE ASSOCIATED 4K HDMI CABLE FOR A COMPLETE SYSTEM.

CONTRACTOR SHALL PROVIDE VIDEO MATRIX SWITCHER (VMS) WITH 8 HDMI SOURCES TO 8 DISPLAYS,

REFER TO DETAIL 2 FOR CONNECTION RISER DETAIL. ATEN MODEL VM0808HA SHALL BE USED AS A BASIS

OF DESIGN FOR THE VMS.

CONTRACTOR SHALL PROVIDE CABINET FOR VIDEO MATRIX SWITCHER.

CONTRACTOR SHALL PROVIDE POWER AND DATA DROPS FOR WIRELESS ROUTERS. ACTUAL LOCATION OF

DROPS SHALL BE CO-ORDINATED WITH WITH ARCHITECT AND OWNER PRIOR TO INSTALLATION.

CONTRACTOR SHALL COORDINATE ACTUAL LOCATION OF SPEAKERS WITH OWNER.

1

2

3

4

5

6

7

8

9

10

GENERAL NOTES:

1. CONTRACTOR SHALL ROUTE ALL DATA CABLES IN THIS AREA TO THE IDF ROOM.

11

12

13

14

1/4" = 1'-0"

E302

2

CLASS-ROOM AUDIO-VISUAL MATRIX RISER

INPUT

OUTPUT

8X8 VIDEO MATRIX SWITCHER (VMS)

AVP

TV

(TYP. OF 5)

HDMI 1

HDMI FOR TV / MONITOR (TYP. OF 5)

HDMI 2

ETHERNET

15

2

2

2

2

NONESCALE:

KNEE WALL

POWER FEED COVERPLATE.

POWER FEED CABLE.

DATA FEED COVERPLATE, PASS & SEYMOUR SS753 OR SIMILAR.

PROVIDE SPIRAL WRAP FOR MANAGING PATCH CABLES OR ZONE

CABLES FROM WALL BOX TO OFFICE PARTITION.

FLOOR

PROVIDE GROMMET STRIP

AROUND EDGE OF CABLE

OPENING TO PROTECT CABLES

FROM SHARP EDGES.

POWER POLE PARTITION FEED DETAIL

POWERPOLE

P

D

E302

3

NOTES:

1. DETAIL IS REPRESENTATIVE OF ANTICIPATED

ARRANGEMENT. THE POWER POLE FOR THE KNEE WALL

SHOULD BE INSTALLED TIGHT TO THE KNEE WALL WITH

POWER AND DATA EXTENDED INTO THE KNEE WALL IN

ACCORDANCE WITH ALL APPLICABLE CODES. POWER PLATE

SHOULD FACILITATE EXTENSION OF POWER CIRCUITS

INDICATED ON PLAN. DATA MANAGEMENT PLATE SHALL

FACILITATE EXTENSION OF CABLING TO LOCATIONS

INDICATED ON PLAN.

2

QA / QC

STORAGE202

WELDING206

TRAININGUNIT SPACE

204

MACHINETECH SPACE

203

CLASSROOM201

EX.CLASSROOM

168

LN1-16,18,20

M

AHU-1

1

2

A

B

C

D

205

9876E

DN

LHA-14,16,18

M

AIR COMPRESSOR

1

2

EX PANEL HA SECT 1

EX PANEL HA SECT 2

EX PANEL LA1 SECT 1 & 2

EX PANEL LA

EX PANEL MDP

EX TRANSFORMER

EX PANEL HA SECT 3

PANEL LHA (NEW)

TRANSFORMER (NEW)

3

TRANSFORMER (NEW)

4

WIRE TROUGH (NEW)

7

6

5

987


ISSUE DATE:

SCALE:

SHEET INFORMATION

M/E/P ENGINEER

STRUCTURAL ENGINEER

CIVIL ENGINEER

LANDSCAPE ARCHITECT

PROJECT ADDRESS

PROJECT OWNER

PROJECT STATUS

PROJECT INFORMATION

REVISIONS

PROJECT TEAM

ARCHITECT

JOB NUMBER:

SHEET TITLE:

SHEET NUMBER:

PROJECT TITLE



TECH HIGHPROGRAMS


100% CD'S

01-17-2020PROJ. #19-0476







am a duly licensed





CJL ENGINEERING

TRUE NORTH

PLANNORTH

KEY PLAN

EXISTING

PROGRAM 1 PROGRAM2




E304

PART FIRST FLOOR ANDMEZZANINE PLANS -

NEW WORK - MECHANICAL POWER

1/4" = 1'-0"

E304

1

PART FIRST FLOOR PLAN - NEW WORK - MECHANICAL POWER

NUMBERED NOTES:

HEAVY DUTY, 240V, 3 POLE, 60A, NEMA 1, NON-FUSED DISCONNECT

3 #4 & 1 #10 EGC IN 1 1/4"C

NEW FLOOR-MOUNTED 75kVA, 480-120/240V, 3-PH, TRANSFORMER TO BE FED

FROM PANEL HA. CONTRACTOR SHALL MOUNT TRANSFORMER PER

MANUFACTURER'S INSTALLATION AND MOUNTING DETAILS.

NEW FLOOR-MOUNTED 225KVA, 480-120/208V, 3-PH, TRANSFORMER TO BE

FED FROM PANEL MDP. CONTRACTOR SHALL MOUNT TRANSFORMER PER

MANUFACTURER'S INSTALLATION AND MOUNTING DETAILS.

DISCONNECT SWITCH FOR PANEL LJ1, SEE DRAWING E601 FOR SWITCH

INFORMATION.

DISCONNECT SWITCH FOR PANEL LJ2, SEE DRAWING E601 FOR SWITCH

INFORMATION.

DISCONNECT SWITCH FOR PANEL LN1, SEE DRAWING E601 FOR SWITCH

INFORMATION.

1

2

1/4" = 1'-0"

E304

2

PART MEZZANINE PLAN - NEW WORK - MECHANICAL POWER

3

4

2

5

6

7

2

ACCU-1

WEF-1

RTU-19

ACCU-2 ACCU-3

1

2

3

4

5

6

7

8

7

8

G1

G2

HA SECT. 2-37

LA1-2,4,6

LA1-5,7,9

LJ1-40,42LJ1-41,43


ISSUE DATE:

SCALE:

SHEET INFORMATION

M/E/P ENGINEER

STRUCTURAL ENGINEER

CIVIL ENGINEER

LANDSCAPE ARCHITECT

PROJECT ADDRESS

PROJECT OWNER

PROJECT STATUS

PROJECT INFORMATION

REVISIONS

PROJECT TEAM

ARCHITECT

JOB NUMBER:

SHEET TITLE:

SHEET NUMBER:

PROJECT TITLE



TECH HIGHPROGRAMS


100% CD'S

01-17-2020PROJ. #19-0476







am a duly licensed





CJL ENGINEERING

TRUE NORTH

PLANNORTH

KEY PLAN

EXISTING

PROGRAM 1 PROGRAM2




E305

PART ROOF PLAN -NEW WORK - MECHANICAL POWER

1/8" = 1'-0"

E305

1

PART ROOF PLAN - NEW WORK - MECHANICAL POWER

NUMBERED NOTES:

HEAVY DUTY, 600V, 3 POLE, 100A, NEMA 3R, FUSED DISCONNECT

WITH 70A FUSES

3 #4 & 1 #8 EGC IN 1 1/4"C

HEAVY DUTY, 240V, 3 POLE, 30A, NEMA 3R, NON-FUSED

DISCONNECT

3 #12 & 1 #12 EGC IN 3/4"C

HEAVY DUTY, 240V, 3-POLE, 60A, NEMA 3R, FUSED DISCONNECT

WITH 35A FUSES

3 #8 & 1 #10 EGC IN 1"C

HEAVY DUTY, 240V, 2 POLE, 30A, NEMA 3R, FUSED DISCONNECT

WITH 25A FUSES

2 #10 & 1 #10 EGC IN 3/4"C

1

2

3

GENERAL NOTES:

ALTERNATE #1: PROVIDE NEW GAS FIRED ROOFTOP UNIT

BASE BID: PROVIDE NEW AIR COOLED CONDENSING UNIT LOCATED

BASE BID: PROVIDE NEW AIR COOLED CONDENSING UNIT

G1

G2

G3

4

5

6

7

8

2

2

AutoCAD SHX Text

C

AutoCAD SHX Text

D

AutoCAD SHX Text

E

AutoCAD SHX Text

F

AutoCAD SHX Text

G

AutoCAD SHX Text

9

AutoCAD SHX Text

10

AutoCAD SHX Text

11

AutoCAD SHX Text

12

AutoCAD SHX Text

13

AutoCAD SHX Text

14

AutoCAD SHX Text

15


ISSUE DATE:

SCALE:

SHEET INFORMATION

M/E/P ENGINEER

STRUCTURAL ENGINEER

CIVIL ENGINEER

LANDSCAPE ARCHITECT

PROJECT ADDRESS

PROJECT OWNER

PROJECT STATUS

PROJECT INFORMATION

REVISIONS

PROJECT TEAM

ARCHITECT

JOB NUMBER:

SHEET TITLE:

SHEET NUMBER:

PROJECT TITLE



TECH HIGHPROGRAMS


100% CD'S

01-17-2020PROJ. #19-0476







am a duly licensed





CJL ENGINEERING

TRUE NORTH

PLANNORTH

KEY PLAN

EXISTING

PROGRAM 1 PROGRAM2




E601

RISER DIAGRAM & PANEL SCHEDULES

DWG.

CCT.

NO.

LOAD

kVA

TRIP

POLE

CIRCUIT DESCRIPTION

PANELBOARD

DIRECTORY

NO. NO.

PANELBOARD DESIGNATION :

LOCATION :

VOLTAGE :

MAINS : 200A MCB

GROUND BUS : COPPER

INTERRUPTING

CAPACITY

MOUNTING :

PANEL TYPE :

:

1 2

3 4

7

5

8

6

11

9

12

10

15

13

16

14

19

17

20

18

23

21

24

22

27

25

28

26

31

29

32

30

35

33

36

34

39

37

40

38

41 42

39

41

35

37

31

33

27

29

23

25

21

19

15

17

11

13

9

7

3

5

1

40

42

32

34

36

38

24

26

28

30

16

18

22

20

10

8

12

14

4

2

6

SQUARE D

SURFACE

22 KAIC

120/208V-3Ø-4W

PANEL LJ1 (NEW)

NO.

CCT.

DWG.

LOAD

kVA

TRIP

POLE

CIRCUIT DESCRIPTION

RM. 104

20/1 20/1

20/1 20/1

20/1 20/1

20/1

20/1

20/1

20/1

20/1

20/1

20/1

20/1

20/1

20/1

20/1

:TOTAL :TOTAL

24.02

25.28

0.36

0.72

0.72

0.72

0.54

0.72

0.72

0.72

0.72

0.54

0.36

20/1

20/1

20/1

20/1

20/1

25/2

20/120/1

20/1

20/1

20/1

20/1

20/1

25/2

RECEPTACLES RM 101

RECEPTACLES RM 101

RECEPTACLES RM 101

RECEPTACLES RM 101

RECEPTACLES RM 101

RECEPTACLES RM 101

RECEPTACLES RM 101

RECEPTACLES RM 106

RECEPTACLES RM 103

RECEPTACLES RM 103

ACCU-2

RECEPTACLES RM 101

RECEPTACLES RM 101

RECEPTACLES RM 101

RECEPTACLES RM 101

RECEPTACLES RM 102

RECEPTACLES RM 101

RECEPTACLES RM 101

RECEPTACLES RM 102

RECEPTACLES RM 103

RECEPTACLES RM 103

RECEPTACLES RM 106

RECEPTACLES RM 106

RECEPTACLES RM 105

RECEPTACLES RM 106

RECEPTACLES RM 106

RECEPTACLES RM 106

RECEPTACLES RM 106

RECEPTACLES RM 103

RECEPTACLES RM 101

ACCU-3

20/1

20/1

RECEPTACLES RM 106

RECEPTACLES RM 106

SPARE

0.72

0.72

0.72

0.72

0.54

0.72

0.72

0.72

0.72

0.72

0.72

0.72

0.72

0.72

0.54

DWG.

CCT.

NO.

LOAD

kVA

TRIP

POLE

CIRCUIT DESCRIPTION

PANELBOARD

DIRECTORY

NO. NO.


LOCATION :

VOLTAGE :

MAINS : 200A MCB

GROUND BUS : COPPER

INTERRUPTING

CAPACITY

MOUNTING :

PANEL TYPE :

:

1 2

3 4

7

5

8

6

11

9

12

10

15

13

16

14

19

17

20

18

23

21

24

22

27

25

28

26

31

29

32

30

35

33

36

34

39

37

40

38

41 42

39

41

35

37

31

33

27

29

23

25

21

19

15

17

11

13

9

7

3

5

1

40

42

32

34

36

38

24

26

28

30

16

18

22

20

10

8

12

14

4

2

6

SQUARE D

SURFACE

22 KAIC

120/208V-3Ø-4W

EX LN

NO.

CCT.

DWG.

LOAD

kVA

TRIP

POLE

CIRCUIT DESCRIPTION

EX 179

20/1 20/1

20/1 20/1

20/1 20/1

20/1

20/1

20/1

20/1

20/1

0.72

0.72

0.72

0.72

0.72

20/1

20/1

20/1

:TOTAL :TOTAL7.28

7.32

0.72

0.72

0.72

0.72

0.72

0.72

0.72

0.72

0.54

0.72

0.72

0.18

0.36

20/1

20/1

20/1

20/1

20/1

20/1

20/120/1

20/1

20/1

20/1

20/1

20/1

20/1

20/1

RECEPTACLES RM 201

RECEPTACLES RM 201

RECEPTACLES RM 201

RECEPTACLES RM 201

RECEPTACLES RM 201

RECEPTACLES RM 201

RECEPTACLES RM 201

RECEPTACLES RM 203

X

X

RECEPTACLES RM 201

RECEPTACLES RM 201

RECEPTACLES RM 201

RECEPTACLES RM 201

RECEPTACLES RM 201

RECEPTACLES RM 201

RECEPTACLES RM 201

RECEPTACLES RM 204

RECEPTACLES RM 204

RECEPTACLES RM 204

WIRELESS ROUTER RM 203

X

X

20/1

PANEL

LJ1

120/208V

1

2

NUMBERED NOTES

4 #4/0 & 1 #4 EGC IN 2 1/2"C

PROVIDE 350A/3P BREAKER IN EXISTING 1200A, 480V, 3-PHASE PANEL MDP FOR NEW TRANSFORMER TMDP. MDP IS

A SQUARE D PANEL WITH CAT. NO. HCR548612U . BREAKER SHALL MATCH PANEL CHARACTERISTICS.

GROUND TRANSFORMER USING 1#3/0 IN 1 1/4"C.

(2) 4 #600 & 1 #3/0 EGC IN 4"C.

4 #3/0 & 1 #6 EGC IN 2 1/2"C

REPLACE EXISTING 30A/3P SQUARE D BREAKER IN CIRCUIT 2,4,6 OF PANEL LA WITH A 35A/3P BREAKER. NEW

BREAKER SHALL MATCH EXISTING PANEL CHARACTERISTICS.

REPLACE EXISTING 20A/3P SQUARE D BREAKER IN CIRCUIT 7,9,11 OF PANEL LA WITH A 15A/3P BREAKER. NEW

BREAKER SHALL MATCH EXISTING PANEL CHARACTERISTICS.

PROVIDE HEAVY DUTY, 240V, 3 POLE, 400A FUSED DISCONNECT. FUSED FOR 225A.

PROVIDE HEAVY DUTY, 240V, 3 POLE, 200A FUSED DISCONNECT. FUSED FOR 200A.

PROVIDE NEW WIRE TROUGH, 8" X 8" X 3'-0". TAP CONDUCTOR SIZE SHALL BE (2) 4-600KCMIL & 1 #3/0 G.

3 #500 & 1 #3 EGC IN 3"C

3

4

5

NOTES:

1.

2.

ALL EQUIPMENT IS TO BE GROUNDED AND BONDED AS REQUIRED BY NEC

ALL WIRE SIZES INDICATED ON RISER DIAGRAM ARE FOR COPPER CONDUCTORS

UNLESS NOTED OTHERWISE.

SECTION 1

PANEL

LN1

120/208V

2

5

MEZZANINE

FIRST FLOOR - RM 104 FIRST FLOOR - RM 203

PARTIAL POWER RISER

43 44

25/2

CRU-1

45 4625/2

CRU-2

47 48

49 5020/1

20/1

SPARE SPARE

51 5220/1

20/1

SPARE SPARE

53 5420/1

20/1

SPARE SPARE

44

46

48

50

52

54

43

45

47

49

51

53

20/1

20/1

20/1RECEPTACLES RM 106







DWG.

CCT.

NO.

LOAD

kVA

TRIP

POLE

CIRCUIT DESCRIPTION

PANELBOARD

DIRECTORY

NO. NO.


LOCATION :

VOLTAGE :

MAINS : 225A MCB

GROUND BUS : COPPER

INTERRUPTING

CAPACITY

MOUNTING :

PANEL TYPE :

:

81

83

77

79

73

75

69

71

65

67

63

61

57

59

53

55

51

49

45

47

43

SQUARE D

SURFACE

22 KAIC

120/208V-3Ø-4W

PANEL LJ2 SECTION II (NEW)

NO.

CCT.

DWG.

LOAD

kVA

TRIP

POLE

CIRCUIT DESCRIPTION

RM. 104

20/1

20/1

EMERGENCY POWER OFF PNL LN120/1

0.72 RECEPTACLES RM 20420/1

DWG.

CCT.

NO.

LOAD

kVA

TRIP

POLE

CIRCUIT DESCRIPTION

PANELBOARD

DIRECTORY

NO. NO.


LOCATION :

VOLTAGE :

MAINS : 200A MCB

GROUND BUS : COPPER

INTERRUPTING

CAPACITY

MOUNTING :

PANEL TYPE :

:

1 2

3 4

7

5

8

6

11

9

12

10

15

13

16

14

19

17

20

18

23

21

24

22

27

25

28

26

29 30

27

29

23

25

21

19

15

17

11

13

9

7

3

5

1

24

26

28

30

16

18

22

20

10

8

12

14

4

2

6

SQUARE D

SURFACE

22 KAIC

120/208V-3Ø-4W

LN1 (NEW)

NO.

CCT.

DWG.

LOAD

kVA

TRIP

POLE

CIRCUIT DESCRIPTION

RM 203

20/1 20/1

20/1 20/1

20/1 20/1

20/1

20/1

20/1

60/3

1.0

1.0

1.0

20/1

20/1

20/3

:TOTAL :TOTAL7.625.3

1.0

1.0

20/3

20/120/1

20/1

CNC LATHE

DRILL

CNC MILL

SPARE

CORD REEL RECEPTACLE RM 204

ELECTRIC EQMT RECEPTACLE RM 204

SPARE

SPARE

CNC LATHE

SPARE

CNC MILL

SPARE

ELECTRIC EQMT RECEPTACLE RM 204

AHU-1

SPARE

SPARE

SPARE

SPARE

SPARE

20/3

20/1

20/1

SPARE20/1

SPARE20/1

SPARE20/1

0.36

0.72

0.72

0.72

0.72

0.54

0.72

0.72

0.72

0.72

0.36

0.36

WITH SHUNT TRIP

0.20

PANEL

LN

120/208V

(NEW)

(NEW)

(EXISTING)

2.50

2.50

3.52

3.52

2.3

2.3

2.3

SECTION 2

PANEL LJ2 (NEW)

225A, 120/208V

DWG.

CCT.

NO.

LOAD

kVA

TRIP

POLE

CIRCUIT DESCRIPTION

PANELBOARD

DIRECTORY

NO. NO.


LOCATION :

VOLTAGE :

MAINS : 225A MCB

GROUND BUS : COPPER

INTERRUPTING

CAPACITY

MOUNTING :

PANEL TYPE :

:

39

41

35

37

31

33

27

29

23

25

21

19

15

17

11

13

9

7

3

5

1

40

42

32

34

36

38

24

26

28

30

16

18

22

20

10

8

12

14

4

2

6

SQUARE D

SURFACE

22 KAIC

120/208V-3Ø-4W

PANEL LJ2 SECTION I (NEW)

NO.

CCT.

DWG.

LOAD

kVA

TRIP

POLE

CIRCUIT DESCRIPTION

EX 104

:TOTAL :TOTAL31.3629.16

1 2

3 4

7

5

8

6

11

9

12

10

15

13

16

14

19

17

20

18

23

21

24

22

27

25

28

26

31

29

32

30

35

33

36

34

39

37

40

38

41 42

20/1 20/1

20/1 20/1

20/1 20/1

20/1

20/1

20/1

DATA POWER STRIP RM 104











1.62

1.62

20/1

20/1

20/1DATA POWER STRIP RM 104

:TOTAL :TOTAL

81

83

77

79

73

75

69

71

65

67

63

61

57

59

53

55

51

49

45

47

43

82

84

78

80

74

76

70

72

66

68

64

62

58

60

54

56

52

50

46

48

44

82

84

78

80

74

76

70

72

66

68

64

62

58

60

54

56

52

50

46

48

44









0.20

0.20

0.20

0.20

0.20

0.20

0.20

0.20

0.20

20/1

20/1

20/1

20/1

20/1

20/1







1.62

20/1

20/1

20/1DATA POWER STRIP RM 104

UPS POWER RECEPTACLE30/1

20/1

20/1

20/1

20/1

20/1




20/1

20/1

20/1




20/1

20/1

20/1




20/1

20/1

20/1




20/1

20/1

20/1




20/1

20/1

20/1

20/1 20/1

20/1 20/1

20/1 20/1

20/1

20/1

20/1

20/1

20/1

20/1

20/1

20/1

20/1

20/1

20/1

20/1

20/1

20/1

20/1

20/1

20/1

20/1

20/1

20/1

20/1

20/1

20/1

20/1

20/1

20/1

20/1

20/1

20/1

20/1

20/1

20/1

20/1

20/1

20/1

20/1

1.62

1.62

1.62

1.62

1.62

1.62

1.62

1.62

1.62

1.62

1.62

1.62

1.62

1.62

1.62

1.62

1.62

1.62

1.62

1.62

1.62

1.62

1.62

1.62

1.62

1.62

1.62

1.62

1.62

1.62

1.62

1.62

1.62

SPARE

SPARE

SPARE

SPARE

SPARE

0.72

20/1

RECEPTACLES RM 106

SPARE

SPARE

SPARE

SPARE

SPARE

SPARE

SPARE

SPARE

SPARE

SPARE

SPARE

SPARE

SPARE

SPARE

SPARE

SPARE

SPARE

SPARE

SPARE

SPARE

SPARE

SPARE

SPARE

SPARE

SPARE

SPARE

SPARE

SPARE

SPARE

SPARE

SPARE

SPARE

SPARE

SPARE

SPARE

SPARE

SPARE

SPARE

SPARE

SPARE

SPARE

SPARE

DWG.

CCT.

NO.

LOAD

kVA

TRIP

POLE

CIRCUIT DESCRIPTION

PANELBOARD

DIRECTORY

NO. NO.


LOCATION :

VOLTAGE :

MAINS : 225A MCB

GROUND BUS : COPPER

INTERRUPTING

CAPACITY

MOUNTING :

PANEL TYPE :

:

1 2

3 4

7

5

8

6

11

9

12

10

15

13

16

14

19

17

20

18

23

21

24

22

27

25

28

26

31

29

32

30

35

33

36

34

39

37

40

38

41 42

39

41

35

37

31

33

27

29

23

25

21

19

15

17

11

13

9

7

3

5

1

40

42

32

34

36

38

24

26

28

30

16

18

22

20

10

8

12

14

4

2

6

SQUARE D

SURFACE

22 KAIC

120/208V-3Ø-4W

PANEL LA (SECTION I)

NO.

CCT.

DWG.

LOAD

kVA

TRIP

POLE

CIRCUIT DESCRIPTION

MEZZANINE

20/1 35/3

20/1

20/1

20/1

X

20/120/1

20/1

20/1

20/1

:TOTAL :TOTAL0.87

8.07

0.87

X

X

X

X

X

X

X

X

X

X

X

X

X

8.07

X

X

X

X

X

X

X

X

X

X

X

X

X

15/3

X

X

X

X

EXISTING LOAD

WEF-1

EXISTING LOAD

EXISTING LOAD

EXISTING LOAD

EXISTING LOAD

X

X

X

X

X

X

X

X

X

X

X

X

X

X

ACCU-1

EXISTING LOAD

EXISTING LOAD

EXISTING LOAD

EXISTING LOAD

X

X

X

X

X

X

X

X

X

X

X

X

X

X

X

X

X

X

7

6

6

7

NOTE: RELABEL PANEL CIRCUIT NUMBER AS SHOWN.

21.0

SPARE20/1

SPARE20/1

SPARE20/1

SPARE20/1

SPARE20/1

SPARE20/1

SPARE

SPARE

SPARE

20/1

20/1

20/1

2

2

2 2



2.20

XFMR

TMDP

225 KVA

(NEW)

3

1

5

200A

EXISTING CIRCUIT

9

8

9

4

8

9

200A

10

10

2

2

11

11

2

2

2

TO MDP

MDP

2

UPUP

EX.TELECOMM

CLOS.178

EX. IDF ROOM207

CLASSROOM102

CISCO / CRANLAB101

SERVERROOM

104

WORK AREA103

CLASSROOM105

AI / CLOUDCOMPUTING

LAB106

(XR)

32/18

RA UP

(XR)32/18

SA UP

(XR)14-3

(XR)14-2

(XR)20/18

(XR)12/12

12/12

(XR)

30/18 RA

S1

275

R1

895

14-6

14-7

14-5

14-4

14-1

S1

235

S1

240

S1

235

S1

240

S1

275

S1

275

S1

275

S1

275

30/12 RA

24/12 RA

24/8

24/8

R1

945

R1

895

R1

750

R1

750

S1

230

S1

235

S1

240

S1

240

S1

235

S1

230

S1

230

S1

230

S1

230

8Ø

8Ø

8Ø

8Ø

12/10 SA

10/10

8Ø

8Ø

8Ø

8Ø

8Ø

8Ø

8Ø

8Ø

8Ø

8Ø

8Ø

8Ø

8Ø

18/10 10/10

20/10

8Ø

8Ø

8Ø

8Ø

24/8

24/8

24/12 RA

24/14 SA

22/16 S

A

20/16 SA

20/10

12Ø

12Ø

12Ø

12Ø

12Ø

20/18

T

T

T

T

CRU-1

1

CRU-2

1

A

M201

B

M201

32/18 SA

18/10

14/10

20/10 SA

12/10

24/8

24/12 R

A

S1

275

S1

275

S1

275

14-4

14-5

T

14-7

14-6

12Ø

S2

375

R3

375

R3

375

R3

375

R3

375

S2

375

S2

375

12/12

12/12

10Ø10Ø

10Ø

10Ø

10Ø

10Ø

10Ø

10Ø

S2

375

12/12

12/12

T

1,21

14-1

RL/RS

CO

2

3/4"

3/4"

3/4"

RL/RS

CONTINUATION

TO M202

RL/RS

32/18

32/18

30/18

(XR)32/18

(XR)32/18

30/8

(XR)32/18

30/12


ISSUE DATE:

SCALE:

SHEET INFORMATION

M/E/P ENGINEER

STRUCTURAL ENGINEER

CIVIL ENGINEER

LANDSCAPE ARCHITECT

PROJECT ADDRESS

PROJECT OWNER

PROJECT STATUS

PROJECT INFORMATION

REVISIONS

PROJECT TEAM

ARCHITECT

JOB NUMBER:

SHEET TITLE:

SHEET NUMBER:

PROJECT TITLE



TECH HIGHPROGRAMS


100% CD'S

01-17-2020PROJ. #19-0476







am a duly licensed





CJL ENGINEERING

TRUE NORTH

PLANNORTH

KEY PLAN

EXISTING

PROGRAM 1 PROGRAM2




M201

PART FIRST FLOOR PLAN -NEW WORK - MECHANICAL

1/4" = 1'-0"

M201

1

PART FIRST FLOOR PLAN - NEW WORK - MECHANICAL

NUMBERED NOTES:

PROVIDE NEW COMPUTER ROOM AIR CONDITIONING

UNIT. EXTEND REFRIGERANT PIPING TO ASSOCIATED

AIR COOLED CONDENSING UNIT LOCATED ON ROOF

ABOVE. REFRIGERANT PIPING TO EXTEND IN EXISTING

SHAFT FOR RTU-14 UP TO ABOVE CEILING ON UPPER

LEVEL OUT OF SHAFT TO ASSOCIATED OUTDOOR

UNIT. CRU-1 & CRU-2 TO SHARE A COMMON

THERMOSTAT. REFER TO SCHEDULE FOR ADDITIONAL

REQUIREMENTS.

CONNECT CONDENSATE PIPING TO EXISTING STORM

WATER PIPE. VERIFY EXACT LOCATION IN FIELD PRIOR

TO NEW PIPE INSTALLATION.

1

NO SCALE

M201

A

SECTION A - NEW WORK - MECHANICAL

M201

B

SECTION B - NEW WORK - MECHANICAL

NO SCALE

2

GENERAL NOTES:

ALL REFRIGERANT PIPING SHALL BE SIZED PER

MANUFACTURER'S REQUIREMENTS.

PROVIDE ALL CLEARANCES PER MANUFACTURER'S

REQUIREMENTS.

G1.

G2.

2

QA / QC205

STORAGE202

WELDING206

TRAININGUNIT SPACE

204

MACHINETECH SPACE

203

CLASSROOM201

TBTP CNCLATHE

TBTP CNCLATHE

TBTP CNCMILL

TBTP CNCMILL

TBTP LATHE TBTP LATHE

TBTP MILL TBTP MILL

IRONWORKER

PRESS

SAWDRILLPRESS

WELDER

A

B

C

D

(XR)15/15

(XR)34/12 TYP.

(XR)25/20

(X

R)3

2/2

0

(XR)32/25

UP

(XR)36/24

UP

(XR)

UH-1

(XR)28/12

(X

R)2

4/2

0

(XR)48/18

UP

(XR)50/20

RAR

(XR)28/12

(XR)34/12

(XR)34/12 TYP.

(XR)6Ø

UP

(XR)

RL/RS

DN

RL/RS

DN

RL/RS

T

(XR)RTU

(XR)15/20

(X

R)1

5/2

0(X

R)24

/20

(X

R)32

/1

2

(XR)RL/RS

(X

R)2

4/2

0

S2

400

S2

400

S2

400

S2

400

12Ø

10Ø

10Ø

10Ø

10Ø

12/12

18/12

AHU-11

10/8

12

Ø

R4

640

R4

640

TAHU-1

8Ø

360

CFM

3

14/14

EA UP

RL/RS

DN

CO

4

3/4"

3/4"

2

5

5

6

885

CFM

RL/RS

UP

RL/RS

CONTINUATION

FROM

M201

RL/RS


ISSUE DATE:

SCALE:

SHEET INFORMATION

M/E/P ENGINEER

STRUCTURAL ENGINEER

CIVIL ENGINEER

LANDSCAPE ARCHITECT

PROJECT ADDRESS

PROJECT OWNER

PROJECT STATUS

PROJECT INFORMATION

REVISIONS

PROJECT TEAM

ARCHITECT

JOB NUMBER:

SHEET TITLE:

SHEET NUMBER:

PROJECT TITLE



TECH HIGHPROGRAMS


100% CD'S

01-17-2020PROJ. #19-0476







am a duly licensed





CJL ENGINEERING

TRUE NORTH

PLANNORTH

KEY PLAN

EXISTING

PROGRAM 1 PROGRAM2




M202

PART FIRST FLOOR PLAN -NEW WORK - MECHANICAL

1/4" = 1'-0"

M202

1

PART FIRST FLOOR PLAN - NEW WORK - MECHANICAL

NUMBERED NOTES:

PROVIDE NEW ELECTRIC AIR HANDLING UNIT LOCATED ABOVE

CEILING. EXTEND REFRIGERANT PIPING TO ASSOCIATED

OUTDOOR UNIT. SIZE AND INSTALL PER MANUFACTURER'S

REQUIREMENTS.

8" ROUND CONNECTION DOWN TO EXTRACTION ARM. INSTALL PER


BALANCE TO INDICATED AIRFLOW.

CONNECT CONDENSATE DRAIN TO EXIT THE BUILDING AT THIS

LOCATION. SPILL TO GRADE ONTO SPLASH BLOCK.

BALANCE TO INDICATED. AIRFLOW WILL BE PROVIDE FROM PRE

DEMOLITION TESTING.

ALTERNATE - #1: BALANCE TO INDICATED AIRFLOW

1 G1.

2

3

GENERAL NOTES:




REQUIREMENTS.

G1.

G2.

4

5

6

2

(XR)RTU

(XR)ACCU

(XR)

FV

ACCU-1

(XR)PRV

(XR)RTU-10

(XR)F-3

(XR)PRV

(XR)PRV-24

(XR)PRV

(XR)PRV

(XR)PRV

(XR)RTU-14

(XR)RTU-4

(XR)RTU-1

(XR)VTR

(XR)RTU-11

G

G

(XR)2"

G

G

(XR)3"

(XR)2

1

2

"

(XR)2"

G

(XR)

1

1

2

"

G

(XR)1

1

2

"

(XR)2"

1

1

2

"

G

(XR)

1

1

2

"

(XR)RTU-3

RL/RS

DN

WEF-1

4

2

RTU-191

ACCU-2

3

ACCU-3

3

RL/RS

DN


ISSUE DATE:

SCALE:

SHEET INFORMATION

M/E/P ENGINEER

STRUCTURAL ENGINEER

CIVIL ENGINEER

LANDSCAPE ARCHITECT

PROJECT ADDRESS

PROJECT OWNER

PROJECT STATUS

PROJECT INFORMATION

REVISIONS

PROJECT TEAM

ARCHITECT

JOB NUMBER:

SHEET TITLE:

SHEET NUMBER:

PROJECT TITLE



TECH HIGHPROGRAMS


100% CD'S

01-17-2020PROJ. #19-0476







am a duly licensed





CJL ENGINEERING

TRUE NORTH

PLANNORTH

KEY PLAN

EXISTING

PROGRAM 1 PROGRAM2




M203

PART ROOF PLAN -NEW WORK - MECHANICAL

1/8" = 1'-0"

M203

1

PART ROOF PLAN - NEW WORK - MECHANICAL

NUMBERED NOTES:

ALTERNATE #1: PROVIDE NEW GAS FIRED ROOFTOP UNIT ON

EXISTING STEEL. CONTRACTOR TO FIELD VERIFY AND CONNECT

TO EXISTING ROOF TOP DUCTWORK. INSTALL PER

MANUFACTURER'S REQUIREMENTS. EXTEND NEW GAS PIPE FROM

EXISTING, MATCH EXISTING PIPE SIZE AS REQUIRED.

PROVIDE NEW AIR COOLED CONDENSING UNIT LOCATED ON

EXISTING STEEL. EXTEND REFRIGERANT PIPING TO ASSOCIATED

INDOOR UNIT. SIZE AND INSTALL PER MANUFACTURER'S

REQUIREMENTS.

PROVIDE NEW AIR COOLED CONDENSING UNIT LOCATED ON NEW

ROOF SUPPORTS. EXTEND REFRIGERANT PIPING TO ASSOCIATED

INDOOR UNIT. SIZE AND INSTALL PER MANUFACTURER'S

REQUIREMENTS.

PROVIDE WELDING EXHAUST FAN ON ROOF CURB. EXTEND

DUCTWORK DOWN THROUGH TO EXTRACTION WELDING ARM.

INSTALL PER MANUFACTURER'S REQUIREMENTS.

1

GENERAL NOTES:

2

3




REQUIREMENTS.

G2.

G1.

4

2

Date post:	17-Aug-2020
Category:	Documents
Upload:	others
View:	3 times
Download:	0 times