201 P- * Adheres to metal, glass, PVC, fiberglass even * Long life * Excellent resistance Hydrophilic waterstop in a 320 ml cartridge * Stays flexible * Excellent chemical resistance * Expands up to 2 times by volume (Check chemical resistance chart) * Long life ADEKA ULTRASEAL A wide variety of uses: * Used with Adeka strip products * Cold/construction/control joints * Waterstop for expanded metal forms * Piping penetrations * Crack / joint repair * Sheet pile interlock sealant *.Precast segment sealant Utility vaults Manholes Tunnels Riser rings 800-999-3959 or www.adeka.com for more information
Transcript
201P-
* Adheres to metal, glass,PVC, fiberglass even
* Long life
* Excellent resistance
Hydrophilic waterstop in a 320 ml cartridge
* Stays flexible * Excellent chemical resistance
* Expands up to 2 times by volume(Check chemical resistance chart)
* Long life
ADEKA ULTRASEAL
A wide variety of uses:* Used with Adeka strip products * Cold/construction/control joints* Waterstop for expanded metal forms* Piping penetrations* Crack / joint repair* Sheet pile interlock sealant*.Precast segment sealant
P-201is a single component hydrophilic pasteused in water-stop and repair applications. It canbe placed on damp or uneven surfaces andfunctions in a wide range of temperatures andground water conditions.
BASIC USE
P-201 is used in piping penetrations, preventingwater penetration in sheet piles, pre-castconcrete joints, and a variety of joint and crackrepair applications. It is used in conjunctionwith formed Adeka water-stops whenever dampor rough surfaces are encountered.
BASIC INSTALLATION
Clean dirt and debris before applying P-201. Thearea may be damp but must not have standingwater. Bead size is controlled by cutting the tipof the cartridge at the proper place. Normal beadsize is approximately 0.25 by 0.50 inches. Cutthe nozzle at the first notch to obtain that beadsize. One cartridge will cover approximately 12linear feet at a bead size of 0.25 by 0.50 inches.Apply a consistent and continuous bead.Expansion occurs in three dimensions and in thedirection of least resistance. Therefore P-201must be encapsulated or injected into a crack orjoint in order to function properly. It is notsuitable for a surface application. Allow time forP-201 to cure before placing concrete.
INSTALLATION
PIPING PENETRATIONS
The P-201 should beplaced on the pipe nearthe center of the wall.
MC-2005T can be used if the pipe diameterexceeds 12 inches. Use MC-2010MN if thediameter is greater than 24 inches. Allowsufficient curing time, 24-36 hours, for the P-201. This is to avoid the possibility of the newconcrete pour tearing the P-201 from the pipe.
EXISTING WALL PENETRATIONS
Apply a ¼" by ½"bead of P-201 to thec en te r o f t hee x i s t i n g w a l l .Remove any dirt orloose debris beforeapplying the bead.
The surface does not have to be smooth or dry.Apply a consistent and continuous bead.
SHEET PILE INSTALLATION
Clean area of dirt anddebris. Stop flowingwater and inject P-201into the interlock areaas shown. Cut the tip ofthe nozzle near the tipto produce a small size
bead that can be injected into the lock. If thesheet pile is under a hydrostatic head, stop theflow of water with Adeka KM string beforeapplying the P-201.
I - BEAM INSTALLATION
Clean around the area ofthe I-Beam beforeplacing the P-201. Applya b e a d s i z eapproximately ¼ by ½inches. Do not allow anygaps in the bead.Overlap and consolidate the area where thebeads meet.
INSTALLATION WITH MC-2010MN
Apply a bead of P-201 before placing MC-2010MN on rough concrete. Apply sufficient P-201 to fill all voids or rough areas.
Use P-201 in any application where an overlapor joining occurs with any other formed water-stop.
SAW CUT CONTROL JOINT
Saw cut the control joint to a depth of 1½ ~ 2inches. Inject P-201 into the joint to a depthof ½ inches. Place backer rod on top of theP-201 as an expansion buffer. Fill theremaining joint area with grout, epoxy orhydraulic cement. There is a chance that thecovering material will be lifted off due to theexpansion pressure of the P-201 if the backerrod is not in place. Do not place P-201 in aposition where it will be exposed to directsunlight.
ADDITIONAL INSTALLATION EXAMPLES
P-201 can be used in pre-cast applications such asutility vaults and storage reservoirs.
P-201 has good resistance to a number ofchemical contaminants. Some chemicals inhigher concentrations may affect theperformance of P-201. Consult your localAdeka representative concerning anyunusual chemical contaminates.
Visit www.adeka.com for warranty and moretechnical information or call (800) 999-3959
Adeka Ultra Seal® P-201
Performance Specification Adeka Ultra Seal P-201 for use in waterstopping cracks, cold joints, construction joints, piping penetrations, between precast segments or between other structural elements against penetration of water from wet-face of structure. Used in conjunction with Adeka strip products on rough concrete. The Product shall be a Hydrophilic Urethane Paste, (cartridge or bulk), and shall meet the minimum performance requirements as shown in the above table. Hydrophilic agent shall be a urethane polymer. The product shall withstand a 150 hydrostatic head when applied in a ½" bead. Adeka Ultra Seal P-201 is manufactured by Adeka Corporation and distributed by OCM, Inc. Chicago, IL. USA Call (303) 904-4624 for sales and technical information.
1 Mass Change % measures the durability of the product. It reflects the amount of material that is lost through repeated cycles of hydration and dehydration. www.adeka.com
Volume Exp. % 100% 1 Mass Change% Not greater than 5.0 %
ADEKA ULTRA SEAL® P-201ADVANTAGES
ADEKA ULTRA SEAL P-201 is a water-swelling, single component, elasticsealant that has a putty-like consistency. P-201 cures when in the presence ofmoisture. Curing time is dependent upon bead size, temperature and humidityconditions. Time will vary but normally P-201 will become firm inapproximately 36 hours. Once cured, P-201 shows the same performance aspre-formed Adeka Ultra Seal products, that is, it exhibits a "DOUBLELOCKING" function by its expansion and its own elasticity.
* Maximum expansion of two times by volume.
* Adheres to concrete, metals, glass, PVC, fiberglass, etc.
* Can be used in damp conditions.
* Applicable to uneven or rough surfaces.
* Excellent chemical contaminant resistance.
* Use in the presence of water contaminated by gasoline, fuel oil, andother hydrocarbons. Contact your local Adeka Ultra SealRepresentative for detailed information.
* Excellent for piping penetrations.
* One of the most versatile Adeka Ultra Seal products.
P201 CURING TIME
HumidityRelative
30%
10mm (0.39") P-201 Bead
to CureDays
Deg F.
1.0862.0772.5685.0598.050
17.541
CartridgeFeet per
InchesBead Size
251/4 x 1/4171/4 x 3/8131/4 x 1/2
8.51/4 x 3/46.31/4 x 1
11.53/8 x 3/88.53/8 x 1/25.53/8 x 3/44.33/8 x 16.51/2 x 1/24.31/2 x 3/43.21/2 x 12.83/4 x 3/42.13/4 x 11.61 x 1
(approx. 11 oz or 19.5 in3)One cartridge of P-201 = 320 ml
P-201 Volume Expansion vs. TimeWeight increase from water intake = volume increase
HYDROSTATIC HEAD RESISTANCEADEKA ULTRASEAL PRODUCTS
Hydrostatic Head psi MPaMC2010MN 150 ft 72.5 0.50MC2005T 50 ft 21.8 0.15KBA 20 ft 8.7 0.06KM3030M 100 ft 43.5 0.30P-201 (3/16x3/4) 50 ft 21.8 0.15P-201 (3/8 x3/4) 150 ft 72.5 0.50
CALL 800.999.3959 OR VISIT WWW.ADEKA.COMFOR MORE INFORMATION
Action Customer
Highlight
MINIMUM CONCRETE COVERAGE
P-201
December 20, 2002
Industrial materials group
Durability data of ADEKA ULTRASEAL P-201
1. Purpose,
There is a difficulty to predict durability of materials. Because, it need to consider many
condition to estimate its durability. But we have to know materials durability to use it.
Degradation of materials is one of chemical reaction, so we can know its durability from heat
degradation. Generally, Arrhenius’s method is used to estimate durability of materials.
Relationship between speed of chemical reaction and temperature is shown as follows by S. A.
Arrhenius in 1889.
K = A exp (-Ea/RT) ----------(1)
K : velocity constant
R : gas constant
T : absolute temperature
A : frequency factor
Ea : activation energy
To estimate materials durability, expression (1) leads expression (2).
ln (t) = Ea/(RT) + const. --------(2)
t : hours
Expression (2) means, logarithm of time “t” proportional to (1/T).
So, promoted test results at high temperature can estimate life of materials at normal condition.
We choose half-life of material’s elongation data to estimate durability of ADEKA
ULTRASEAL P-201.
2. Promoted degradation test
Testing condition is shown at table-1.
Table-1) Testing condition
Test item Elongation
Temperature 50,70 and 90 degrees C
Predict method Half-life of elongation
Testing method JIS K 6251
Result
Fig.1) Relationship between change of elongation and days
We can read half-life of elongation from Fig.1) as follows, Expression (3) - (5) show
approximate expression of change of elongation and days data.
y = -6.6362 ln (x) + 10.69 --------(3)
y = -6.5231 ln (x) + 6.4195 --------(4)
y = -7.1223 ln (x) + 4.826 --------(5)
y : change of elongation
x : days
Temperature
(Deg C)/(Deg F)/(K)Days t (hrs)
90 / 194 / 363
70 / 158 / 343
50 / 122 / 323
2,203
5,705
9,370
52,884
136,932
224,886
-60
-50
-40
-30
-20
-10
0
1 1 0 1 0 0 1 0 0 0 1 0 0 0 0d a y s
Ch
an
ge
of e
lon
ga
tio
n(%
)
5 0 d e g C
7 0 d e g C
9 0 d e g C
3. Predict of material’s life
Expression (2) and Table-1 show relationship of ln (t) and 1/T as follows.
Fig.2 ) Relationship between ln (t) and (1/T)
ln (t) = 4.2122 * (1/T) * 103
– 0.633 ---------(6)
Expression (6) leads durability of ADEKA ULTRASEAL P-201 at 20 – 30 degrees C as
follows.
Table-2. Durability of ADEKA ULTRASEAL P-201
Temperature
(Deg C)/(Deg F)/(K)Predicted Durability (years)
20 / 68 / 293
25 / 77 / 298
30 / 86 / 303
106
83
66
This predict method results estimate degradation time at controlled conditions, so these data
does not estimate durability at actual condition. Materials are using in many kinds of conditions,
so its durability are different in many cases. But this durability data is useful to know ADEKA
ULTRASEAL P-201 has good degradation resist ability.
(End)
P-201
Piping Penetration
P-201
Pre-Cast
Vaultsand
Segments
0.5"
2.0" 0.5"
Grout or Joint SealantBacker rod
P-201
Control Jointand
Crack Repair
Typical Usesof
P-201
Cross Section of Manhole with riser rings
Lid
Steel Rim
P-201
Riser Rings
Barrel of Manhole
1/2" X 3/4" P-201 Bead Between Riser Rings
Not to Scale
Riser Rings
P-201
2"
Cork or similar
Grout
Grout
½" Laryer of P-201
Sealing Taper Tie Holes With Adeka Ultra Seal P-201
P-201
Approximately1/2 X 3/4 inchbead size.
P-201
Bead Sizecompressed toapproximately 1/4 X 1 1/2 inches.
