aeg_ewm_2500_2100

SERVICE MANUAL

Electrolux Distripart GmbHMuggenhofer Strae 135D-90429 NrnbergGermany

Fax +49 911 323 1022

DGS-TDS-N

Publ.-Nr.:599 52 93 04685

10.07

U / min Option OKTemp.

40-60 Mix20 min - 3 kg

Edition

WASHING

EN

Washing machines,Toploader

LCD-applianceEWM 2500, 2100

ENV 06Serie 6-low, Serie 6,Serie 7, Serie 7-high

AEG

Wool Plus

Dessous

Outdoor

Sportintensive

Energy Off

Silk

Quick intensive

Cottons/Coloured

DrainSchonschleudernSpin

Delicate RinseViskose

Delicates

Easy ironPlus

Synthetics

Hygiene

Jeans

Quick

Delayed start

Start / Pause

- 2 -DGS-TDS-N 10.07 R.B. Electrolux 599 52 93 04 EN

CONTENTS

Control Panel / Multifunctionsdisplay LCD.......................................................................3 - 10

Push Buttons................................................................................................................. 11 - 13

Programselector / Programme ..................................................................................... 14 - 15

Buzzer / Extra rinse cycle / Child safety .......................................................................16

Functions of the System ...............................................................................................17 - 18

Connection electronic ................................................................................................... 19

Electronic Module .......................................................................................................... 20

Door Lock ......................................................................................................................21

DSP Function (Drum Self Position) .............................................................................. 22

Float switch / Inlet valve with flow-meter-sensor ...........................................................23

Water Inlet Valve for 3-chamber detergent box ............................................................. 24

Water Distributor ...........................................................................................................25

Analogic pressure switch .............................................................................................. 26

Heating element ...........................................................................................................27

Heating Circuit ............................................................................................................... 28

Drain pump / Circulation pump / Motor ..........................................................................29

Motor / Motor control board ............................................................................................ 30

Drum movements / Spin Profiles .................................................................................. 31 - 33

Function of the FUCS ....................................................................................................34 - 35

Foam Detection ............................................................................................................. 36

Service Program ...........................................................................................................37 - 45

Demo Program ............................................................................................................. 46

Electronic-Test ..............................................................................................................47

Operating time............................................................................................................... 48

Circuit Diagram ............................................................................................................. 49 - 52

Program ........................................................................................................................53 - 59

Changes ........................................................................................................................60


B ACDEFGH

40

30

40

30 4030

4050

60

9560

30

40

40-60Mix

30 min - 2.5 kg

C BDFGHIJ

900

700

400

1200

U / min40

30

40

30 40 3040

50

60

9560

30

40

40-60Mix

E A

30 min - 2.5 kg

900

700

400

1200

U / min

Control Panel

Version Serie 6-low (Premium-design)

A Start, Pause F StainB Cycles G PrewashC Multifunctionsdisplay LCD H SpinD Quick I Programselector

Version Serie 6 (Premium-design)

A Delayed start F SensitiveB Start, Pause G StainC Cycles H PrewashD Multifunctionsdisplay LCD I SpinE Quick J Programselector

Rinse-hold

Start / Pause

Extra rines

Ende

Wash

QuickStainEasy iron Plus

Off

Wool PlusSilk

Delicates

cold

Cottons/Coloured

Synthetics

Spin

Drain

Rinse

Energy

Pre-wash

Duration

Rinse-hold

Start / Pause

Extra rines

Ende

Wash


Off

Wool PlusSilk

Delicates

cold

Cottons/Coloured

Synthetics

Spin

Drain

Rinse

Energy

Pre-wash

Duration

Sensitive


A B C

Multifunktionsdisplay LCD

A Display C Delayed startB Child safety

Display

Function:- delayed start selection with the delayed start button- cycle duration and remaining time indicated in hours and minutes 2.08 (e.g. 2h08min)- information on error codes (e.g. E10)- End of cycle when 0.00 is indicated.

Child safety

Function:- All keys are blocked (see page 16).

Delayed start

Function:- Die Startzeitvorwahl ist aktiviert (see page 10)

Standby

Function:- After 10 minutes of standby in the pre-selection position or at the end of the cycle, the light of the

Display switches off and the LED Start/Pause flashes slowly.Pressing any button or rotating the selector, the appliance returns to the normal status (followingmodel MCF-file).


B A

C BDFGHIJ

900

700

400

1400

U / min40

30

40

30 40 3040

50

60

9560

30

40

40-60Mix

E A

E CD

30 min - 3 kg

Multifunktionsdisplay LCD

A Display D Door lockB Delayed start E Child safetyC Cycles

Control Panel

Version Serie 7 (Premium-design)

A Delayed start F SensitiveB Start, Pause G StainC LED indicate H PrewashD Multifunctionsdisplay LCD I SpinE Quick J Programselector

Rinse-hold

Start / Pause

Extra rines

Overdosing


Off

Wool PlusSilk

Delicates

cold

Cottons/Coloured

Synthetics

Spin

Drain

Rinse

Energy

Pre-wash

Duration

Sensitive


Display


Delayed start


Cycles

Door lock

Function:- Das Waschprogramm wurde ber die Start/Pause-Taste aktiviert.- Die Trverriegelung hat den Gertedeckel verriegelt.

Child safety


Standby


Display switches off and the LED Start/Pause flashes slowly.Pressing any button or rotating the selector, the appliance returns to the normal status (followingmodel MCF-file).

Symbol Status processON cycle is running (lid closed)OFF lid not closed

washing rinse drain spin


ABCDEFGHI

ABCGH EF DIJ


20 min - 3 kg 40-60 Mix

Control Panel

Version Serie 7-high (Premium-design)

A Delayed start F OptionB Start, Pause G SpinC Multifunctionsdisplay LCD H TemperatureD Quick I ProgramselectorE OK

Multifunctionsdisplay LCD

A Cycles F QuickB Overdosing G Door lockC Child safety H OptionsD Delayed start I SpinE Display J Temperature

Wool Plus

Dessous

Outdoor

Sportintensive

Energy Off

Silk

Quick intensive

Cottons/Coloured



Delicates

Easy ironPlus

Synthetics

Hygiene

Jeans

Quick

Delayed start

Start / Pause


Symbol Status processON cycle is running (lid closed)OFF lid not closed

Cycles

Overdosing

Function:- wird bei berdosierung am Programmende angezeigt.

Child safety


Delayed start


Display


Quick

Function:- Die Programmlaufzeit kann durch drcken der Zeitsparen-Taste 2x reduziert werden.

z.B. Koch-/Buntwsche 60150 min 1x press ---> 140min 2x press ---> 45min

Door lock

Function:- Das Waschprogramm wurde ber die Start/Pause-Taste aktiviert.- Die Trverriegelung hat den Gertedeckel verriegelt.

Option

Function:- Depending on model there can be various additional features.

prewash washing rinse drain spin


Spin

Function:- A corresponding symbol is indicated depending on the selected speed.- Bei deaktiviertem Schleudern, erscheint keine Anzeige.- Animated spiral symbol during spin cycle.- Night cycle- and Rinse hold-Symbol

Temperature

Function:- A corresponding symbol is indicated depending on the selected temperature.- The temperature is indicated in degree Celsius.

Standby


Display switches off and the LED Start/Pause flashes slowly.Pressing any button or rotating the selector, the appliance returns to the normal status.


Push Buttons

Spin deselection button

Function:- By pressing this key, you can reduce spin-dry speed step by step down to zero, to rinse hold or to

night cycle.- Reduces the spinning speed of all spin-dry cycles.

Temperature button

Function:- To activate the temperature button it is necessary to select a program.- By pushing this button the washing temperature can be reduced to 0C step-by-step.

Start/ Pause button

Function:- The selected program is activated by pressing the start/pause button.

The LED start/pause on.- If the cycle is to be paused, press the start/pause button.

Start/ Pause-LED blinks. The program interrupt.- This is not possible after a program run time of 10 min..

Delayed Start button

Function:- Hold the delayed start button pressed, the start time will be indicated in the display and counted

up, the start time can be selected max. from 0h, 30', 60', 90', 2h - 20h.- The start time is counted down hour by hour, from 90 min in steps of 30 minutes,

from 30 min in steps of minutes.- Change of delayed start: - switch off the programselector

- select a new program again

adjust temperature

95C 60C 50C 40C 30C 0C

1500 1200 1000 800 600 400 0 Night Cycle Rinse hold1400 1200 1000 800 600 400 0 Night Cycle Rinse hold1300 1000 800 600 500 400 0 Night Cycle Rinse hold1200 1000 800 600 500 400 0 Night Cycle Rinse hold1100 800 700 600 500 400 0 Night Cycle Rinse hold1000 800 700 600 500 400 0 Night Cycle Rinse hold

LED status process (red) ON cycle is running (lid closed)

(red) Flashing cycle in pause position lid not closed) (orange) Flashing additional option key pressed, after program start. Err in display.

OFF

start/pause


Pre-Wash-button

Function:- It is heated up to max. 30 C.- Can't be combined with the programe wool, silk and sport 30.

Stains-button

Function:- The selected temperature however must be >=40C.- Separate rinsing in of stain remover through the pre-wash chamber, approx. 1.2 ltrs.- Can't be combined with the pre-wash function.- Extends the cycle duration in the main wash by 5 minutes after the first heating to 40C.

Sensitive-button

Function:- It is heated up to max. 60 C.- Das Programm besteht aus einer Hauptwsche, vier Splgngen mit einem Zwischenschleudern

(1200 1/min).

Quick-button

Function:- Die Programmlaufzeit kann durch drcken der Zeitsparen-Taste 2x reduziert werden.

e.t. Cottons/Coloured 60150 min 1x press ---> 140min 2x press ---> 45min

Option-button

Function:- Nach Auswhlen eines Waschprogrammes, knnen verschiedene Zusatzfunktionen angewhlt

werden.

OK-button

Function:- Ist eine zustzliche Funktion angewhlt, wird diese mit der OK-Taste aktiviert.

Funktion nicht aktiviert ---> Funktion aktiviert --->


Options

The selection of the options is to be carried out after switching on the appliance and setting the desiredprogramme with the selector and before pressing the start/pause button.

90C X X X X X X X X X X X X X X X X X60C X X X X X X X X X X X X X X X X X50C X X X X X X X X X X X X X X X X X40C X X X X X X X X X X X X X X X X X30C X X X X X X X X X X X X X X Xcold X X X X X X X X X X X X X X X60C X X X X X X X X X X X X X50C X X X X X X X X X X X X X40C X X X X X X X X X X X X X30C X X X X X X X X X X Xcold X X X X X X X X X X X40C X X X X X X X X X X X30C X X X X X X X X X Xcold X X X X X X X X X X40C X X X X30C X X X Xcold X X X X60C X X X X X X X50C X X X X X X X40C X X X X X X X30C X X X X X X Xcold X X X X X X X40C X X30C X X60C X X X X X X X X50C X X X X X X X X40C X X X X X X X X30C X X X X X X X Xcold X X X X X X X X40C X X X X X X30C X X X X X Xcold X X X X X X40C X X X X X30C X X X X Xcold X X X X X30C X X X X Xcold X X X X X40C X X X X X X X30C X X X X X X Xcold X X X X X X X

Sport light, Min 30C X X XSanitr 90C X X X X X X X X X5 Shorts 30C X XMIX 40-60 40C X X X X X X X X X X

90C X X X X X X X X X60C X X X X X X X X X50C X X X X X X X X X40C X X X X X X X X X60C X X X X X X X X X50C X X X X X X X X X40C X X X X X X X X X

Express 60C X X X XSensitiv Plus 60C X X X X X X X X X XQuick 30C X X XSoak 30C X X

X X X X X X XX X X X XX X X X X

XX

ConditionerDrainSpin

Gentle spin

Hygiene +

Gras

Rinsessoftener

Shoes

Lingerie

Silk

Baby, Sport intensiv

Com

patib

ility

with

pro

gram

mes

Cotton

Synthetic

Delicates

Wool

Easy iron

Blanket

Jeans

Rin

se-h

old

Nig

ht c

ycle

Pre

-was

h

Sta

ins

Ble

ach

Ext

ra ri

nse

Eas

y iro

n

Eco

Inte

nsiv

Nor

mal

Dai

ly

Ligh

t

Qui

ck

Sup

er q

uick

Red

uced

spi

n sp

eed

no s

pin

Hal

f-loa

d

Programmes

Options


Function:Rince hold

- The program is finish with water in the drum.- In order to continue a program afterwards, you first have to select a separate draining or spinning.

Function:Night Cycle

- The number of rinces are increase cotton/cotoured from three rinces to six rinces andsynthetic from three rinces to four rinces.

- All rinces are without a spinphase.- The programm is stopped in a rinse hold.- In order to continue a program afterwards, you first have to select a separate draining or spinning.- Switches off the buzzer ( if configured)

Function:Pre-Wash

- It is heated up to max. 30 C.- Can't be combined with the programe wool, silk and sport 30.

Function:Stains

- The selected temperature however must be >=40C.- Separate rinsing in of stain remover through the pre-wash chamber, approx. 1.2 ltrs.- Can't be combined with the pre-wash function.- Extends the cycle duration in the main wash by 5 minutes after the first heating to 40C.

Function:Extra rinse

- Two additional rinse cycles are added in the cycle cotton / coloured.- One additional rinse cycle are added in the cycles synthetics, delicate fabrics and silk.- No intermediate rinse, except after the last rinse cycle.

Function:Easy Iron 40With cotton/coloureds programmes:

- No intermediate spin-dry cycle.- 3 additional rinse cycles.- Pulse spin-dry- Additional loosening phase after spin-drying

With synthetics programmes:- Reduced wash temperature- Prolonged wash time and prolonged cooling phase- One additional rinse cycle- Additional loosening phase after spin-drying

Function:Energy Saving

- The washing temperature in the programs:- E90C is reduced to 67C, the max. temperature kept constantly for a certain period of time.

E60C is reduced to 40C, the max. temperature kept constantly for a certain period of time.E40C is reduced to 40C, the max. temperature achieved for a short moment.

- Can't be combined with the quick function.


Programme

Jeans

Function:- The cycle includes a main cycle, five rinse cycles. (1. and 2. rinses without intermediate spins

and 3., 4., 5. rinses with intermediate spins max.1200 1/min).- The load amount is 3kg.- Can be combined with the Night Cycle Pre-wash and Spin deselection button.

Shoes 30, 40

Function:- The program consists of a main wash, three rinses without intermediate spins but with an

end spin. (1000 1/min).- It is heated up to 40 C.- Can be comdined with the Quick, Extra rinse, Night Cycle, Pre-wash, Soaking and Spin

deselection button.

Silk 30


end spin. (700 1/min).- Washing time during main wash is 10 min.- The load amount is 1kg.

Baby 30, 40

Function:- The program consists of a main wash, three rinses with higher water levels without intermediate

spins, but with an end spin. (700 1/min).- The load amount is 2kg.

Sanitr 90

Function:- The program consists of a main wash, three rinses with intermediate spins but with an

end spin. (1200 1/min).- Washing temperature during main wash is kept constantly to 85 for 10 min.- The load amount is 5,5kg.

Programselector

Depending on the model, the electronic may includea programselector with 21-positions.The programselector includes the on/off functionand the wash programs.


Dessous 30, 40


end spin. (900 1/min).- The load amount is 1Kg.

Blanket 30, 40

Function:- The program consists of a main wash, three rinses with higher water levels

(20ltr.) intermediate and end spin. (650 1/min).- The load amount is 2,5kg.

Soak

Function:- The soaking period begins with pre-wash and soaks for about the next 30 minutes.- Can't be combined with the function pre-wash.- It is heated up to 30 C.- A short spin cycle is performed in the cycles COTTON and SYNTHETICS, before passing on to the

main wash.- You can prolong soaking time for max. 0h, 30', 60', 90', 2h - 10 h using the Start preset key.- After pressing the start key, the duration of the cycle is displayed by hours and minutes.

Sport light 30

Function:- The program consists of a main wash, two rinses with higher water levels without intermediate

spins, but with an end spin. (700 1/min).- The load amount is 2kg.

Sport intensive 30, 40

Function:- The cycle consists of prewash, higher water level, heating to 30 and spin cycle to 650 1/min, one

main wash, two rinse cycles without intermediate spin with higher water level but with final spin(900 1/min).

- The load amount is 2,5kg.

Hygiene 60

Function:- The program consists of a main wash, three rinses with intermediate spins (1000 1/min) but with

an end spin. (1500 1/min).- The load amount is 6kg.


21 4 5 63


20 min - 3 kg 40-60 Mix

Activation and deactivation of the buzzer:

Function:- Depending on the model, the electronic may include a buzzer.- Switch off the appliance.- Hold buttons 3 and 2 pressed simultaneously and turn the program selector one position to the

right. The buzzer is activated.- You can deactivate the buzzer by repeatedly pressing the key combination.

Activation and deactivation of the extra rinse cycle:

Function:- If no extra rinse key is available, you can select extra wash.- This button is effective in the cycles cotton/coloured wash, synthetics and delicate fabrics.- Two additional rinse cycles are added.- No intermediate rinse, except after the last rinse cycle.- Switch off the appliance.- Hold buttons 4 and 2 pressed simultaneously and turn the program selector one position to the

right. The extra rinse is activated.- You can deactivate extra wash by repeatedly pressing the key combination.

Activation and deactivation of the child safety:

Function:- The child safety function can be activated at the start of the program and also after

the program has started.- Press keys 4 and 3 simultaneously and hold until a symbol appears on the LCD.- The option is activated, the initiated wash program runs normally through and on

completion any further function of the appliance is disabled. The option remains saved when theappliance is turned off.

- You can deactivate child safety by repeatedly pressing the key combination.

Buzzer, Extra rinse cycle, Child safety

Wool Plus

Dessous

Outdoor

Sportintensive

Energy Off

Silk

Quick intensive

Cottons/Coloured



Delicates

Easy ironPlus

Synthetics

Hygiene

Jeans

Quick

Delayed start

Start / Pause


1

6

3 4

5 7 8

2

9 10

Functions of the System

Electronic EWM2100 with universal motor AC

1. electronic module2. motor3. heating element4. door security5. drain pump6. circulation pump7. NTC-sensor8. inlet valve with flow-meter-sensor9. analog pressure switch10. drum self position (DSP)


1

7

4 5

6 8 9

2 3

10 11

Functions of the System

Electronic EWM2500 with asynchronous three-phase motor

1. electronic module2. motor control board3. motor4. heating element5. door security6. drain pump7. circulation pump8. NTC-sensor9. inlet valve with flow-meter-sensor10. analog pressure switch11. drum self position (DSP)


87543

6

21

1110843

9

21

6

5 7

Connection cable electronic

Electronic EWM2100

1. multifunctionsdisplay LCD2. drum self position (DSP)3. analogic pressue switch4. NTC-sensor, Inlet valve with flow-meter-sensor5. motor, drain pump6. Power supply 230V7. heating element8. door security

Electronic EWM2500

1. multifunctionsdisplay LCD2. drum self position (DSP)3. flow-meter-sensor4. analogic pressue switch5. NTC-sensor, Inlet valve6. Power supply motorcontrol board7. motorcontrol board +5V, +15V8. drain pump, circulation pump9. Power supply 230V10. heating element11. door security


Electronic Module

The electronic module, including the P, controls various functions and is placed in a protective housing.

It is the communication interface between the user and the appliance.

It consists of:

- The option buttons and the multifunctiondisplay LCD.- The programselector with 21-positions.- The time display and the alarm identification.- The Start/Pause button.

Functions:- Taking data of the selected cycle programs through the module.- Water level control (antifoam, overflow level) in the tub; the level is recognized by the analog

pressure switch.- Cycle temperature control by a NTC sensor.- Power supply of the heating element.- Power supply of the drive motor (EWM2100) and control of its speed by the tachymetric generator.- Control of the motor control board (EWM2500).- Control of water inlet valves.- Control of drain pump, circulation pump, door lock and DSP (drum self position).

In case of a power failure the module saves the just paused cycle.

- When the power supply to the appliance is restored again, the cycle starts where the program waspaused.


5 4 3 2

5

2

3

4

Door Lock

Version magnetic

locking part

make-and-breakcontact

PTC bimetal

tooth lock washer

lever

magnetic coil

2 = N3 = impulse electronic4 = L5 = electronic J1-2

When closing the lid the door lock gets an impulse from the electronic by contact 3. The impulse feedsthe magnetic coil over the PTC resistor. This moves the lever down and the tooth lock washer isforwarded by another tooth. This can be heard by a click. The locking part is unlocked, the lid is closed.

When opening the lid, e.g. with the start/pause button or at the end of the cycle, the door lock gets twoimpulses from the electronic. The tooth lock washer is moved twice. Only because of the second impulsethe lid can be opened immediately.The second impulse unlocks the locking part mechanically through the tooth lock washer.Why two impulses?The door lock is controlled by a triac which is on the main circuit board. If there is a triac short circuit, theelectronic sends an impulse to the door lock. The customer could open the appliance, if the secondimpulse was not required.

If there is a power failure during a wash cycle, the door lock requires approx. 2 min until the lid can beopened. During this time the PTC bimetal cools down and the locking part opens.

Circuit Diagram

Security:(see page Service - Program fault display E40)

pin Fe


DSP (Drum-Self-Position)

Control ( check ) the DSP-Function:

1. Remove the side panel, switch on the appliance- Turn the drum to the right position ---> LED on- Turn the drum over the right position ---> LED off

2 Remove the two plugs from the DSP and checkthe resitance of the reed relay.- Turn the drum to the right position ---> > 0- Turn the drum over the right position ---> 0

3 The drum is still in the right position.Now measure the voltage. 5-6V DC- If there is no voltage ---> Cable,

Main electronic boardis defective

4. Check the In / Output electronic in the customersservice test program.- LED on ---> In / Output electronic OK.- LED off ---> In / Output electronic defective.

Function:The reed relay is closed if the metalic sheet, located on the pully, isn't between the magnet and the reedrelay. If the position of the metalic sheet is between those parts the contact of the reed relay is opened.

To mount the pulley in the correct way, you have to take care about following items:The metal sheet located on the pulley should be in the drum self positioning device, if the door of thedrum is in the upper postion. The DSP is supplied with 5-6 V DC by the main board.

Condition drum positioned:Reed contact opened, LED-Drum positioned illuminated, 5-6V DC.Condition drum out of postion:Reed contact closed, LED-Drum positioned not illuminated, 0V.

If the washing cycle is interrupted by the start pause button the drum has to be postioned within 10 sec.During this time 2-3 attempts can be excecuted.If the drum isn't positioned during this time, the lid of theappliance is released and can be opened. The LED drum positioned is not illuminated.At the end of the cycle the positioning phase is 2 min until time out is reached.

Magnet

Reed - Switch

Connections


Inlet valve with flow-meter-sensor

Depending on the type of appliance, the automatic washer can be equipped with a 2-fold inlet valve withor without flow-meter-sensor.

Function:The inlet valve includes a flow meter sensor. The flow meter sensor emits electrical pulses of 5V to themain electronic. This is enabled by a magnet which opens and shuts a reed contact. The magnet islocated on a movable turbine 2. Because of the water pressure the turbine rotates and thus givesimpulses to the main electronic. The water pressure of > 1 bar is limited by the volume regulator to 5.5 l/min +15%/-15%.(see Page Service - Program fault display EC0)

Turbine 2 with magnet

Reed-SwitchSieve

Turbine 1

Flow control regulator

Coil

Float switch

The float switch is made of a housing with a microswitch and a float body.

Function:The float switch is located in the bottom tray. Thebottom tray is constructed in a way that the water isgathering in the area of the float switch in case ofleaky components (tub, hoses, etc.). The float bodycomes up and switches a micro switch.This selects the drain pump, the existing water inthe tub is drained. The inlet valve is switched off.

FloatStyropor

Micro-switch


4

2

3

2

1

5

6

Water Inlet Valve for 3-chamber detergent box

*) Attention!The simultaneous filling through hoses 3 and 4 provides the fill-in through the softener chamber.

Softener Pre washMain wash

1 - connection water inlet hose2 - inlet valve, 2-fold3 - hose for pre-wash4 - hose for main wash5 - water distributor6 - hose for fluff filtre


Water Distributor

Pre wash chamberMain wash chamber

Water inletpre wash chamber

Water inletmain wash chamber


Analogic pressure switch

The analogic pressure switch controls the water level in the tub, it is directly connected to the electronicmodul.

If the pressure switch does not work correctly, the programm in progress is cancelled:

1. Pressure switch hose connection2. Diaphragm3. Coil (self)4. Electronic circuit (oscillator)5. Magnet6. Spring7. Adjusting screw8. Connector

Kontakt 1 = OutKontakt 2 = GNDKontakt 3 = 5V DC

When the tub is full, the pressure inside the hydraulic circuit acts on the diaphragm which moves themagnet insidethe coil.

This moving modifies the inductance of self and consequently the frequence delivered by the scillatorycircuit. the P, after frequence reading, recognizes the water level inside the tub. (see Page Service -Program fault display E30)

Frequence delivered follow the pressure ( 50 Hz)


Connection: 230V; 50Hz;Power: 1950WFuse: 10A

Heating element

The heating element is supplied with power directly from the controlelectronics by means of a relay. For security reasons, 2 switchingcontacts of the pressure switch are connected in series. Theswitching positions are monitored by control electronics via 2 controllines.

1. Heating element2. Temperature fuse3. NTC-sensor4. Connection

Check of insulation resistance with the heating

Wash a cycle for approx. 10 minutes. Switch off the appliance, unplugthe plug and remove the side panel.Draw off the connecting lines from the heater.Measure the resistance between heating (depending on connection)and mass.Resistance > 200 kOhm > heater OK.Resistance < 168 kOhm > error E68


Heating Circuit

The cycle temperature is fixed by the P depending on the selected program.The temperature control is guaranteed by the P through the NTC temperature sensor. The temperaturesensor reduces its resistance according to the temperature increase.The reduction in the ohmio value of the temperature sensor is detected by the P; as soon as theselected temperature is reached the power supply to the heating element will be paused.The NTC sensor is integrated in the heating element.

Variations of NTC resistance

Temperature (C) Resistance (Ohm)25 4815 +- 20740 2563 +- 102,560 1196 +- 26,3180 602 +- 19,89

NTC-Sensor

1. NTC resistance2. Metallic casing3. Connections4. Plastic casing

To check the NTC sensor function you can measure the ohmic resistance between the contacts J9/8 and J9/9.

Security

- The P will be break off if an anomaly on the termistance circuit is detected :cut or short-circuit. (see Page Service-Program fault display E70)

- The heating phase is not executed.


Drain pump / Circulation pump

The drain pump and circulation pump is directly controlled via triac from the control electronics.

Connection:

Motor

Electronic EWM2100

The motor is directly phase-controlled via triac from the control electronics.Relays K2, K3 are responsible for commuting the sense of rotation.Field switching (if any) is controlled by relay K4.Speed is monitored by tachometer generator g1 and controlled by control electronics.Integral overheat protection disconnects the motor from power supply at 115C.

Safety- If the triac for the motor is in short-circuit, or if the tachometer generator is interrupted, 4 trials are

executed in intervals of 5 minute each.After a break of 20 minutes, the fifth and last trial is started. If the motor does not run this time, theprogramme is aborted.(see Page Service-Program fault display E60)


Motor, Motor control board

Electronic EWM2500

These appliances include a 2-pin asynchronous three-phase motor. This motor is directly driven by aspecial inverter motor electronic system. This changes the frequencies of the rotary current inaccordance with the required rotational speed. The motor electronic system is connected with the controlelectronic system via a control line.

Connection:

The ohmic resistance of the tacho generatoramounts to approx. 119 Ohms. The measurableresistance of the motor coils can be measuredbetween the connection contacts of motorsm4-m5 / m4-m6 / m5-m6 and amount toapprox. 5.5 Ohms in each case. The phase shiftbetween the phases is 120 and peak amplitudeis 310V.

Safety- If the transistor for the motor is in short-circuit, or if the tachometer generator is interrupted, 4 trials

are executed in intervals of 5 minute each.After a break of 20 minutes, the fifth and last trial is started. If the motor does not run this time, theprogramme is aborted.(see Page Service-Program fault display E50)


D55Sek. 1/Min.12 04 5512 04 -55

N 55Sek. 1/Min.

8 08 558 08 -55

E 55Sek. 1/Min.

3 010 553 010 -55

E 55Sek. 1/Min.

3 010 503 010 -50

PWL_1Sek. 1/Min.40 01 3540 01 -35

PWL_4Sek. 1/Min.57 01 3557 01 -35

Drum movements


C01/Min. Sek. ASFUCS x nein300 0 neinFUCS x nein450 0 neinFUCS x nein450 5 nein650 0 nein

C11/Min. Sek. ASFUCS x nein

FUCS imp x neinFUCS x nein450 30 AS650 15 AS850 10 AS850 60 nein

C21/Min. Sek. ASFUCS x nein


COT_CF1/Min. Sek. ASFUCS x nein

FUCS imp x neinFUCS x nein450 30 AS650 15 AS850 5 AS1000 95 nein1150 75 nein1400 110 nein

SYN_CF1/Min. Sek. ASFUCS x nein

FUCS imp x neinFUCS x nein450 5 nein650 10 nein900 55 nein

Spin profiles


CF (Feinwsche)1/Min. Sek. ASFUCS x nein

FUCS imp x neinFUCS x nein450 35 AS700 5 AS900 20 AS

CF (Wolle)1/Min. Sek. ASFUCS x nein


Separater Schleudergang1/Min. Sek. ASFUCS x nein

FUCS imp x neinFUCS x nein450 10 AS650 10 AS850 10 AS1000 10 nein1150 10 nein1400 20 nein

EASY_IRON_IMP1/Min. Sek. ASFUCS x nein450 0 neinFUCS x nein650 0 ASFUCS x nein800 0 ASFUCS x nein900 0 AS

CSR1/Min. Sek. ASFUCS x nein

FUCS imp x neinFUCS x nein450 120 AS

Spin profiles

AS indicates that the anti-foam function is active.


1/min

1/min

Perfect balance

- Reversing- FUCS phase 0

with spin-dry pulse- Reversing- FUCS phase 1- regular spin-dry

Function of the FUCS

FUCS is an English expression and means Fast Unbalanced Control System

Function:The unbalance control includes 4 phases. These phases are of different duration and have different limitsof unbalance. The magnitude of the unbalance is calculated every 300 ms, hereby the magnitude iscompared to the fixed unbalance limits, and then it is decided whether the speed will be increased orreduced by 2 1/min. FUCS starts at 55 1/min and ends ideally when reaching 115 1/min.

Phase 0: When the unbalance threshold (850gr.) of the first phase is reached, the appliance performsa spin cycle with 100 1/min for 5 sec followed by a spin cycle pulse of 470 1/min.

Phase 1: The first phase (350gr.) takes max. 120 sec to obtain the required speed of 115 1/min. If thespeed is not reached after this 120 sec, the spinning cycle will be stopped. The laundry isdispersed and it is changed to phase 2.

Phase 2: Phase 2 (650gr.) takes max. 60 sec. Here it is tried to obtain the speed of 115 1/min withvarious unbalance limits. If the speed is not reached after 60 sec, the spinning cycle will bestopped again. The laundry is dispersed and it is changed to phase 3.

Phase 3: In phase 3 (1100gr.), the required speed is reduced to 85 1/min. Within 90 sec, speed shouldbe reached, the machine then runs a spin-dry cycle at 100 1/min for 5 sec.and a subsequentspin-dry pulse at 470 1/min, then again starting by phase 1. If the speed is reached, areduced spin-dry cycle at 650 1/min is carried out. If the speed is not reached, spin-dry isskipped.

for tub C4

for tub C3


Balancing after two attempts

- Low speed- FUCS phase 0- FUCS phase 1- FUCS phase 2

Balancing after the third phase (normal spin-speed)

- FUCS phase 0with spin pulse

- FUCS phase 1- FUCS phase 2- FUCS phase 3

with spin pulse- FUCS phase 1- FUCS phase 2- FUCS phase 3- Normal spin

Balancing after the third phase (reduced spin-speed)

- FUCS phase 0- FUCS phase 1- FUCS phase 2- FUCS phase 3

with spin pulse- FUCS phase 1- FUCS phase 2- FUCS phase 3- reduced-speed spin

Unalancing after the third phase

- FUCS phase 0- FUCS phase 1- FUCS phase 2- FUCS phase 3- FUCS phase 1- FUCS phase 2- FUCS phase 3- no spin


FUCSFUCS

Foam Detection

Anti-foam control is excited via analog pressure switch.

Spin-drySpin-dry

Pulse with200 1/Min

Pulse with200 1/Min

Anti-Foam

Spin-dry phase without foam: Spin-dry phase with little foam:

Spin-dry with little foam:

When the analogous pressure switch detects foam (45 mm full), the spinning cycle is stoppedand the drain pump keeps on running until the foam level will be fallen below (15 mm empty) andthe spinning cycle is continued.

Spin-dry with excess foam:

When the analogous pressure switch detects a foam 5 times (45 mm full), the spinning will beskipped. Draining is carried out for 1 minute with the motor at stop. If too much foam is detectedduring any wash cycle, an additional rinse cycle is added.


21 4 5 63


40-60 Mix20 min - 3 kg

Service Program

Fault indication by multifunctionsdisplay LCD- Switch off the appliance.- Hold buttons 6 and 5 pressed simultaneously and turn the program selector one position to

the right.- Hold the two selected buttons pressed until possibly a buzzer will sound and/or the LCD will

give a light.- By the program selector it is possible to interrogate the desired checking function according

to the table.

Wool Plus

Dessous

Outdoor

Sportintensive

Energy Off

Silk

Quick intensive

Cottons/Coloured



Delicates

Easy ironPlus

Synthetics

Hygiene

Jeans

Quick

Delayed start

Start / Pause

Position of the rotary switch Button Test function

Off Off21

Positions01 Button 6 1) Start of the customer service testprogram

and 2) LCD - TestButton 5 LEDs are step by step illuminated.

If you press a button the according LED is on.

02 Water channel mainwash Water intake up to savety level fS Time max. 5 min Valve mainwash Display indicates current water level in mm

03 Water channel prewash Water intake up to savety level fS Time max. 5 min Valve prewash Display indicates current water level in mm

04 Water channel softener Water intake up to savety level fS Time max. 5 min Valve mainwash and prewash Display indicates current water level in mm

05 Water channel spots Water intake up to savety level fS Time max. 5 min Valve spots or hotwater Display indicates current water level in mm

06 Heating and circulation pump Heating up to 90C Time max. 10 min Water intake over mainwash chamber Display indicates current temperature in C

07 Tub leakage test Water intake over mainwash chamber up to 1. Niv. Motor rotation 250 1/min Display indicates current speed in 1/min

08 Draining and spinning Draining Spinning up to maximium spin speed, if level < fSch Display indicates current speed in 1/min

09 DSPThe drum is positioned if level < fSch

10 Displaying the error code (programme display)


No. Electronic Software1 EWM20002 EWM1000 W1D001093 EWM1000 W1D002004 EWM1000plus5 EWM2000EVO6 EWM2000NEW7 EWM3000NEW

EWM1100EWM2120EWM2130EWM2131EWM2521EWM2531EWM3541

8

Service Program

Fault indication by multifunctionsdisplay LCD

Type

of f

ault

Rem

edy

No.

1No

.2

No.

3No

.4

No.

5No

.6

No.

7No

.8

Fau

lt co

deA

larm

C

ode

Alarm state

0 Program cycle interrupted S Start Button1 Program cycle interrupted A Off / On

Door locked2 Program cycle stopped

Drain pump is activatedt3 Heating step is skipped4 Program canceled5 DSP-function is skipped6 after 5 attempt

Composition alarm codesReactivate

the machine with


Service Program

Fault indication by multifunctionsdisplay LCDTy

pe o

f fau

ltR

emed

yNo

.1

No.

2No

.3

No.

4No

.5

No.

6No

.7

No.

8 F

ault

code

Ala

rm

Cod

e

E10

E11

No w

ater

filli

ng1

SX

XX

XX

XX

XW

ater

tap

clos

edO

pen

tap

Val

ve d

oes

not o

pen

/ int

erru

ptio

nCh

ange

the

valv

eV

alve

flow

rate

to lo

wCl

ean

filte

rA

ir tra

p sy

stem

leak

ing

Repl

ace

air t

rap

Cabl

e de

fect

Cabl

e pr

essu

re s

witc

h an

d el

ectro

nic

Elec

troni

c de

fect

Repl

ace

elec

troni

cE1

3No

t eno

ugh

wat

er1

SX

XX

XX

XX

Wro

ng d

rain

pip

e po

sitio

nCh

eck

the

drai

n pi

pe p

ositio

nV

alve

flow

rate

to lo

wCl

ean

filte

rIn

let v

alve

def

ect

Repl

ace

inle

t val

vePr

essu

re s

witc

h de

fect

Repl

ace

pres

sure

sw

itch

Hose

for p

ress

ure

switc

h le

akag

e or

blo

cked

Chec

k th

e ho

se fo

r the

pre

ssur

e sw

itch

E20

E21

No d

rain

ing

0S

XX

XX

XX

XX

Pum

p bl

ocke

d / n

ot w

orkin

gRe

mov

e fo

reig

n ob

ject

Pum

p in

terr

upte

dRe

plac

e dr

ainp

ump

Redu

ced

pum

p ou

tput

rate

Chec

k dr

aini

ng s

yste

mPr

essu

re s

witc

h de

fect

Repl

ace

pres

sure

sw

itch

Pres

sure

sen

sor d

efec

tRe

plac

e pr

essu

re s

enso

rEl

ectro

nic

defe

ctRe

plac

e el

ectro

nic

E23

Inco

ngru

ence

bet

wee

n dr

ainp

ump

and

elec

troni

cRe

plac

e dr

ainp

ump,

2

AX

XX

XX

XX

Cabl

e dr

ainp

ump

E24

Drai

n pu

mp

triac

sen

sing

failu

re 1

Inpu

t vol

tage

allw

ays

0V o

r 5V

Repl

ace

elec

troni

c2

AX

XX

XX

XX

E30

E31

Pres

sure

sen

sor d

efec

tRe

plac

e pr

essu

re s

enso

r1

AX

XX

XX

Freq

uenc

y of

the

pres

sure

sen

sor o

ut o

f lim

itCa

ble

inte

rrup

ted

Repl

ace

cabl

eE3

2Ca

libra

tion

prob

lem

s pr

essu

re s

enso

rO

pen

tap

0S

XX

XX

XA

fter i

nitia

l cal

ibra

tion

the

wat

erle

vel n

otRe

plac

e in

let v

alve

in b

etw

een

0 - 6

6mm

and

ant

iboi

l leve

l off

Clea

n fil

ter

Repl

ace

air t

rap,

Rep

lace

pre

ssur

e se

nsor

E33

Inco

ngru

ence

bet

wee

n pr

essu

re s

enso

rRe

plac

e pr

essu

re s

enso

r1

AX

XX

Xan

d an

tiboi

l leve

l 1Re

plac

e ca

ble

Faul

t has

to b

e fo

r a ti

me

long

er th

an 6

0 se

c.Re

plac

e ai

r tra

pE3

3In

cong

ruen

ce b

etw

een

pres

sure

sw

itch

Niv.

1Re

plac

e pr

essu

re s

witc

h, R

epla

ce e

lect

roni

c1

AX

XX

and

antib

oil le

vel 1

Repl

ace

heat

ing

elem

ent

Faul

t has

to b

e fo

r a ti

me

long

er th

an 3

sec

.Ca

ble

pres

sure

sw

itch

and

elec

troni

c


Service Program

Fault indication by multifunktionsdisplay LCDTy

pe o

f fau

ltR

emed

yNo

.1

No.

2No

.3

No.

4No

.5

No.

6No

.7

No.

8 F

ault

code

Ala

rm

Cod

eE3

4In

cong

ruen

ce b

etw

een

pres

sure

sen

sor

Repl

ace

pres

sure

sen

sor

1A

XX

XX

and

antib

oil le

vel 2

Repl

ace

cabl

eFa

ult h

as to

be

for a

tim

e lo

nger

than

60

sec.

Repl

ace

air t

rap

E35

Safe

ty le

vel (

Pres

sure

sen

sor)

Re

plac

e pr

essu

re s

enso

r1

AX

XX

XLe

vel h

as to

be

300m

m fo

r a ti

me

of m

ore

than

15

sec

Repl

ace

cabl

eDr

ain

pum

p w

ill be

act

ivat

ed u

ntil l

evel

is b

elow

120

mm

Repl

ace

air t

rap

E35

Safe

ty p

ress

ure

switc

h on

for a

tim

e lo

nger

than

15

sec.

Repl

ace

inle

t val

ve, R

epla

ce e

lect

roni

c2

AX

XX

XA

ir tra

p sy

stem

leak

ing

Repl

ace

pres

sure

sw

itch

Cabl

e pr

essu

re s

witc

h an

d el

ectro

nic

E36

Ant

iboi

l 1 s

ensi

ng fa

ilure

1 In

put v

olta

ge a

llway

s 0V

Repl

ace

elec

troni

c1

AX

XX

XX

XX

E37

Ant

iboi

l 2 s

ensi

ng fa

ilure

1 In

put v

olta

ge a

llway

s 0V

or 5

VRe

plac

e el

ectro

nic

1A

XX

XX

E37

Pres

sure

sw

itch

Niv.

1 se

nsin

g fa

ilure

Inpu

tvol

t. al

lway

s 0V

or 5

VRe

plac

e el

ectro

nic

1A

XX

XE3

8A

irtra

p bl

ocke

dCh

ange

airt

rap

1A

XX

XX

No p

ress

ure

diff

eren

ces

dete

cted

Clea

n ai

rtrap

E39

sen

sing

failu

re In

putv

olt.

allw

ays

0VRe

plac

e el

ectro

nic

1A

XX

XX

XX

E3A

Heat

ing

elem

ent r

elay

def

ect

Repl

ace

elec

troni

c1

AX

XX

XE4

0E4

1Li

d op

en0

SX

XX

XX

XX

XDo

or lo

ck d

efec

tRe

plac

e do

orlo

ckCa

ble

defe

ctRe

plac

e ca

ble

Elec

troni

c de

fect

Repl

ace

elec

troni

cE4

2Do

or lo

ck d

efec

tRe

plac

e do

orlo

ck0

SX

XX

XX

XX

XDo

or is

unl

ocke

d du

ring

the

cycl

e To

ut 1

5 se

cRe

plac

e ca

ble

Door

is n

ot u

nloc

king

at th

e en

d of

cyc

le T

out 4

min

Repl

ace

elec

troni

cE4

3Do

or lo

ck tr

iac

defe

ctRe

plac

e do

orlo

ck, R

epla

ce c

able

0A

XX

XX

XX

XX

Repl

ace

elec

troni

cE4

4Do

or lo

ck s

ensi

ng fa

ilure

Inpu

tvol

tage

allw

ays

0V o

r 5V

Repl

ace

elec

troni

c1

AX

XX

XX

XX

XE4

5Do

or lo

ck tr

iac

sens

ing

failu

re In

putv

olta

ge a

llway

s 0V

or 5

VRe

plac

e el

ectro

nic

1A

XX

XX

XX

XX

E50

E51

Mot

ortri

ac s

hort

circ

uit

Repl

ace

cabl

e1,

6A

XX

XX

XX

XM

otor

cab

le s

hort

circ

uit

Repl

ace

elec

troni

cE5

2No

sig

nal f

rom

tach

ogen

erat

or

Repl

ace

tach

ogne

rato

r 1,

6A

XX

XX

XX

XX

Mot

or b

lock

edRe

plac

e m

otor

Mot

or c

able

def

ectiv

eRe

plac

e ca

ble

Repl

ace

elec

troni

cE5

3M

otor

tria

c se

nsin

g fa

ilure

Inpu

t vol

tage

allw

ays

0V o

r 5V

Repl

ace

elec

troni

c1

AX

XX

XX

XX


Service Program


pe o

f fau

ltR

emed

yNo

.1

No.

2No

.3

No.

4No

.5

No.

6No

.7

No.

8 F

ault

code

Ala

rm

Cod

eE5

4M

otor

rela

y de

fect

Repl

ace

elec

troni

c1,

6A

XX

XX

XX

XE5

5M

otor

circ

uit i

nter

rupt

edRe

plac

e m

otor

, Rep

lace

cab

le1

AX

E56

No s

igna

l fro

m ta

chog

ener

ator

, No

sign

al a

fter 1

5 m

inRe

plac

e ta

chog

nera

tor

1A

XE5

7In

verte

r cur

rent

goe

s ab

ove

thre

shol

d (>

15A

)Re

plac

e m

otor

, rep

lace

cab

le1,

6A

XX

Repl

ace

mot

or c

ontro

l boa

rdE5

8M

otor

pha

se c

urre

nt g

oes

abov

e th

resh

old

(>4,

5A)

Repl

ace

mot

or, r

epla

ce c

able

1,6

AX

XRe

plac

e m

otor

con

trol b

oard

E59

No ta

cho

sign

al fo

r 3 s

econ

ds a

fter n

ew s

peed

targ

etRe

plac

e m

otor

, rep

lace

tach

ogen

erat

or1,

6A

XX

diff

eren

t fro

m z

ero

Repl

ace

mot

or c

ontro

l boa

rd, r

epla

ce c

able

E5A

Heat

Sin

k te

mpe

ratu

re g

oes

abov

e th

resh

old

(88

C)Re

plac

e m

otor

con

trol b

oard

1,6

AX

XE5

BDC

bus

vol

tage

goe

s be

low

thre

shol

d (43

0V)

Repl

ace

mot

or c

ontro

l boa

rd1,

6A

XX

E5D

FCV

can

not r

ecei

ve a

nd/o

r tra

nsm

it a

mes

sage

for m

ore

Repl

ace

cabl

e1,

6A

XX

than

2 s

econ

dsE5

ETh

ere

are

com

mun

icat

ion

prob

lem

s in

bet

wee

n FC

VRe

plac

e el

ectro

nic

1A

XX

cont

rol b

oard

and

mai

nboa

rdE5

FFC

V c

ontro

l boa

rd is

con

tinuo

usly

ask

ing

for c

onfig

urat

ion

Repl

ace

mot

or c

ontro

l boa

rd, r

epla

ce c

able

1A

XX

para

met

ers

due

to re

petit

ive

rese

tRe

plac

e el

ectro

nic

E60

E61

Insu

ffic

ient

hea

ting

Repl

ace

NTC

3S

XX

XX

XX

XX

Max

imum

hea

ting

time

expi

red

Repl

ace

heat

ing

elem

ent

NTC

defe

ctiv

eRe

plac

e ca

ble

Heat

ing

elem

ent d

efec

tCo

nnec

tion

heat

ing

elem

ent i

nter

rupt

edE6

2O

verh

eatin

g:2

AX

XX

XX

XX

XTe

mpe

ratu

re g

reat

er 8

8C

for a

tim

e lo

nger

than

5 m

inRe

plac

e NT

CNT

C de

fect

ive

Repl

ace

heat

ing

elem

ent

Cabl

e de

fect

ive

Repl

ace

cabl

eE6

6He

atin

g el

emen

t def

ect

Repl

ace

pres

sure

sw

itch

antb

oil 2

2A

XIn

cong

ruen

ce b

etw

een

antib

oil 2

and

rela

yRe

plac

e ca

ble

E66

Heat

ing

elem

ent d

efec

tRe

plac

e pr

essu

re s

witc

h an

tboi

l 12

AX

XX

XX

XX

Inco

ngru

ence

bet

wee

n an

tiboi

l 1 a

nd re

lay

Repl

ace

elec

troni

cRe

plac

e ca

ble

E68

Leak

age

curr

ent i

n th

e ap

plia

nce

too

high

.Re

plac

e he

atin

g el

emen

t7

AX

or re

plac

e ot

her c

ompo

nent

sE6

9No

hea

ting

Repl

ace

heat

ing

elem

ent

3S

XV

olta

ge v

alue

by

heat

ing

rela

is o

ut o

f lim

its (5

V)

Repl

ace

cabl

e


Service Program


pe o

f fau

ltR

emed

yNo

.1

No.

2No

.3

No.

4No

.5

No.

6No

.7

No.

8 F

ault

code

Ala

rm

Cod

e

E70

E71

NTC

shor

t circ

uit

Repl

ace

NTC,

Rep

lace

ele

ctro

nic

3S

XX

XX

XX

XX

NTC

inte

rrup

tion

Repl

ace

cabl

eE7

4NT

C is

n't i

n th

e co

rrec

t pos

ition

in th

e tu

bCh

eck

the

posi

tion

3S

XX

XX

XE8

0E8

2W

rong

sel

ecto

r res

et p

ostio

n de

tect

ion

Repl

ace

elec

troni

cA

XX

XX

XX

XE8

3W

rong

sel

ecto

r rea

ding

Wro

ng c

onfig

urat

ion

of th

e m

achi

ne4

SX

XX

XX

XX

Repl

ace

elec

troni

cE8

4Re

circ

. pum

p se

nsor

ing

failu

re In

put v

olta

ge a

llway

s 0V

or 5

VRe

plac

e el

ectro

nic

1A

XX

XX

XE8

5Re

circ

ulat

ion

pum

p de

fect

Repl

ace

reci

rcul

atio

n pu

mp

2A

XX

XX

XTr

iac

defe

ctiv

eRe

plac

e el

ectro

nic

E90

E91

Inte

rrup

ted

com

mun

icat

ion

Repl

ace

cabl

e, R

epla

ce e

lect

roni

c0

AX

XX

XX

Xbe

twee

n In

/Out

put e

lect

roni

c an

d m

aine

lect

roni

cRe

plac

e In

/Out

put e

lect

roni

cE9

2In

cong

ruen

ce b

etw

een

In/O

utpu

t ele

ctro

nic

and

elec

troni

cIn

/Out

put e

lect

roni

c is

inco

mpa

tible

1A

XX

XX

XX

with

ele

ctro

nic

E93

Conf

igur

atio

n er

ror

Wro

ng c

onfig

urat

ion

of th

e m

achi

ne1

AX

XX

XX

XX

XE9

4Lo

st o

f cyc

le d

atas

Wro

ng c

onfig

urat

ion

of th

e m

achi

ne1

AX

XX

XX

XX

XRe

plac

e el

ectro

nic

E95

Com

mun

icat

ion

erro

r bet

wee

n m

icro

proc

esso

r and

EEP

ROM

Repl

ace

elec

troni

c0

AX

XX

XX

XX

E96

Inco

ngru

ence

bet

wee

n Ha

rdw

are-

vers

ion

and

Wro

ng c

onfig

urat

ion

of th

e m

achi

ne0

AX

Xcy

cles

con

figur

atio

nRe

plac

e el

ectro

nic

E97

Inco

ngru

ence

bet

wee

n se

lect

or a

nd c

ycle

s co

nfig

urat

ion

Wro

ng c

onfig

urat

ion

of th

e m

achi

ne0

AX

XX

XX

XX

Repl

ace

elec

troni

cE9

8In

cong

ruen

ce b

etw

een

Repl

ace

elec

troni

c0

AX

mot

or c

ontro

l boa

rd a

nd e

lect

roni

cRe

plac

e w

iring

E99

Conn

ectio

n be

twee

n lo

udsp

eake

r and

In/O

utpu

t ele

ctro

nic

Repl

ace

loud

spea

ker

0A

XX

Repl

ace

wiri

ngE9

AFi

rmw

are

betw

een

loud

spea

ker a

nd In

/Out

put e

lect

roni

c no

t ok

Repl

ace

In/O

utpu

t ele

ctro

nic

0A

XX

E9F

Com

mun

icat

ion

erro

r bet

wee

nRe

plac

e el

ectro

nic

1,6

AX

mot

or c

ontro

l boa

rd a

nd e

lect

roni

cRe

plac

e w

iring


Service Program


pe o

f fau

ltR

emed

yNo

.1

No.

2No

.3

No.

4No

.5

No.

6No

.7

No.

8 F

ault

code

Ala

rm

Cod

e

EA0

EA1

DSP

defe

ctRe

plac

e DS

P, R

epla

ce e

lect

roni

c5

SX

XX

XX

XX

XRe

plac

e w

iring

, Cut

driv

e be

ltEA

2DP

S se

nsin

g de

fect

Repl

ace

elec

troni

cX

EA3

DPS

unab

le to

lock

mot

or p

ully

Repl

ace

DSP,

Rep

lace

ele

ctro

nic

XRe

plac

e w

iring

, Cut

driv

e be

ltEA

4DP

S de

fect

Repl

ace

DPS

XRe

plac

e el

ectro

nic

Repl

ace

wiri

ngEA

5Tr

iac

for D

PS d

efec

tRe

plac

e el

ectro

nic

XEA

6Dr

um h

ave

bloc

ked

in th

e fir

st c

a. 3

0sec

.Cu

t driv

e be

lt, R

epla

ce D

SP0

AX

XX

XX

Drum

lid n

ot c

lose

dEA

6Dr

um h

ave

bloc

ked

in th

e fir

st c

a. 3

sec.

Cut d

rive

belt,

Rep

lace

DSP

0A

XDr

um lid

not

clo

sed

EB

0EB

1Po

wer

sup

ply

freq

uenc

y ou

t of l

imits

Wro

ng o

r dis

turb

ed p

ower

sup

ply

line

0A

XX

XX

XX

Repl

ace

elec

troni

cEB

2Po

wer

sup

ply

volta

ge to

o hi

ghW

rong

or d

istu

rbed

pow

er s

uppl

y lin

e0

AX

XX

XX

XRe

plac

e el

ectro

nic

EB3

Pow

er s

uppl

y vo

ltage

too

low

Wro

ng o

r dis

turb

ed p

ower

sup

ply

line

0A

XX

XX

XX

Repl

ace

elec

troni

cEB

ELi

ne S

afe

rela

y fa

ulty

Repl

ace

elec

troni

c2

AX

EBF

Line

Saf

e "s

ensi

ng" f

aulty

Repl

ace

elec

troni

c2

AX

EC

0EC

1In

let v

alve

blo

cked

Repl

ace

inle

t val

ve, R

epla

ce e

lect

roni

c2

AX

XRe

plac

e w

iring

EC2

Turb

idity

sen

sor d

efec

tRe

plac

e tu

rbid

ity s

enso

rX

EF0

EF1

Filte

r dirt

yCl

eani

ng d

rain

hose

and

filte

rS

XX

XX

XX

Drai

nhos

e cl

osed

Chec

king

drai

npum

pTi

me

for d

rain

ing

to lo

ngEF

2De

terg

ent o

verd

osin

gCl

eani

ng d

rain

hose

and

filte

r6

AX

XX

XX

XTo

muc

h fo

am d

urin

g th

e dr

ain

phas

eCh

eckin

g dr

ainp

ump

Filte

r dirt

yNo

t ove

rdos

ing

Drai

nhos

e cl

osed


Service Program


pe o

f fau

ltR

emed

yNo

.1

No.

2No

.3

No.

4No

.5

No.

6No

.7

No.

8 F

ault

code

Ala

rm

Cod

eEF

3A

qua

Cont

rol s

yste

m a

ctiv

ated

Leak

age

in th

e m

achi

ne2

AX

XX

XX

XDr

ain

pum

p ca

ble

defe

ctiv

eRe

plac

e ca

ble

Drai

n pu

mp

inte

rrup

tion

Repl

ace

drai

n pu

mp

EF4

No s

igna

l fro

m fl

ow m

eter

with

ele

ctro

val

ves

switc

hed

onW

ater

tap

clos

ed o

r mai

ns p

ress

ure

0X

XX

insu

ffic

ient

.EF

5In

terr

upte

d th

e sp

inni

ng p

hase

Pay

atte

ntio

n to

the

quan

tity

of la

undr

y,0

XUn

bala

nce

to h

igh,

unb

alan

ce >

1200

grch

eck

stat

iona

ry b

ehav

iour

of w

ashe

r

EH0

EH1

Pow

er s

uppl

y fr

eque

ncy

out o

f lim

itsW

rong

or d

istu

rbed

pow

er s

uppl

y lin

e0

AX

Repl

ace

elec

troni

cEH

2Po

wer

sup

ply

volta

ge to

o hi

ghW

rong

or d

istu

rbed

pow

er s

uppl

y lin

e0

AX

Repl

ace

elec

troni

cEH

3Po

wer

sup

ply

volta

ge to

o lo

wW

rong

or d

istu

rbed

pow

er s

uppl

y lin

e0

AX

Repl

ace

elec

troni

cEH

ELi

ne S

afe

rela

y fa

ulty

Repl

ace

elec

troni

c2

AX

EHF

Line

Saf

e "s

ensi

ng" f

aulty

Repl

ace

elec

troni

c2

AX


Service Program

Rapid reading of alarm codes

The last alarm code can be displayed even if the programme selector is not in the 10th position(service test mode) or if the appliance is in normal operating mode (e.g. during the execution of anwashing programme):

- Keep buttons 6 and 5 pressed in together.

- The alarm sequence continues as long as the two buttons are held down

- While the alarms are displayed, the appliance continues to perform the cycle or, if in theprogramme selection phase, maintains the previously-selected options in memory.

Indication of error code through LEDs

The error code is additionally indicated by the START/PAUSE LED.The START/PAUSE LED is a double LED with colors orange and red.When the orange LED is flashing (0.5 sec on, 0.5 sec off), the alarm family will be indicated, when thered LED is flashing afterwards, the alarm number will be indicated.

e.g. EA4

- EA4 ---> orange LED flashes 10 x

- pause of 1.5 sec

- EA4 ---> red LED flashes 4 x

- pause of 2.5 sec, then repetition

Cancelling the last alarm

- Enter service test program (page 37)

- Press buttons 6 and 5 in together and keep them pressed in until the LCD E00.

It is good practice to cancel the last alarm:

- after reading the alarm code, to check whether the alarm re-occurs during diagnostics

- after repairing the appliance, to check whether it re-occurs during testing.

Alarm codes flashing1 1 x: :9 9 xA 10 xB 11 x: :H 17 x


21 4 5 63

40-60 Mix


20 min - 3 kg

Demo-Programm

Activate the demo - program

These appliances have a Demo-Mode for demonstration purposes.

main electronic EWM2100 Software WBD101..WBE202..

main electronic EWM2500 Software WCB101..WCC202..

1. Access to demo program- Switch off the appliance.- Keep buttons 6 and 5 pressed in together and rotate the programme selector three

positions to the right.- Keep both selected keys pressed for about 2 seconds.- You can select the individual programs and the associated option keys by using the

program selector switch.The key start/pause is disabled.

- The demo program will remain in the memory even if the appliance is switched Off.

2. Adandoning the demo program- Switch off the appliance.- Keep buttons 6 and 5 pressed in together and rotate the programme selector three

positions to the right.- Keep both selected keys pressed for about 2 seconds.- Switch Off the appliance to deactivate the demo program.

Wool Plus

Dessous

Outdoor

Sportintensive

Energy Off

Silk

Quick intensive

Cottons/Coloured



Delicates

Easy ironPlus

Synthetics

Hygiene

Jeans

Quick

Delayed start

Start / Pause


21 4 5 63

Aus

40-60 Mix


20 min - 3 kg

Electronic-Test

Activate the electronic-test

1. Access to the electronic-test

- Switch off the appliance.- Hold buttons 6 and 5 pressed simultaneously and turn the program selector one

position to the right.- Keep both selected keys pressed for about 2 seconds.- Hold buttons 6 and 5 together and pressed again.- Switch off and on the appliance- The display indicates ELE- The electronic-test it running

- Filling till 1. Niveau- Movement with 50 1/min.- Heating up to max. 50C or 20min duration.

2. Adandoning the elektronik-test

- Switch off the appliance.

Wool Plus

Dessous

Outdoor

Sportintensive

Energy Off

Silk

Quick intensive

Cottons/Coloured



Delicates

Easy ironPlus

Synthetics

Hygiene

Jeans

Quick

Delayed start

Start / Pause


Serie 6-lowSerie 6

Serie 7

Serie 7-high

21 4 5 63


40-60 Mix20 min - 3 kg

Operating time

Activate the operating time

1. Access to the operating time- Switch off the appliance.- Keep buttons 6 and 5 pressed in together and rotate the programme selector five

positions to the right.- Keep both selected keys pressed for about 2 seconds.

2. Adandoning the operating time- Switch off the applinace.

1. display after 2 sec. 2. display

e.t. 3364 operating time

Wool Plus

Dessous

Outdoor

Sportintensive

Energy Off

Silk

Quick intensive

Cottons/Coloured



Delicates

Easy ironPlus

Synthetics

Hygiene

Jeans

Quick

Delayed start

Start / Pause


Circuit Diagram

Technicl Specifications

GENERAL FEATURES

Supply voltage....................................................... 230 VDimensions (height, width, depth) ............... 85/40/60 cmDryclothes loading capacity .................................. 5,5 kgDrum rotation speed (washing/spinning)55/600-1500 r.p.mIntermediate speed ......................................... 1000 r.p.mIntermediate speed ...........................................850 r.p.m

WATER LOAD CAPACITY (without clothes) :Heating Level I .............................................................2 lHeating Level II ............................................................2 lAnti-overflow level ...................................................... 43 l

WATER PRESSURE :Max./Min. .................................................. 0,8/0,05 MPa

CONSUMPTIONS (COTTON 60) :see energie label

TECHNICAL PARTICULARS

DRAIN PUMP :Maxi head ........................................................... 100 cmMini head .............................................................. 70 cmDelivery rate ...................................................... 25 l/minPower absorbed ..................................................... 30 WWinding resistance .................................... 164/224 ohm

HEATING ELEMENT :Power absorbed ................................................. 1950 WResistance .......................................................... 27 ohm

WATER VALVE :Delivery rate ...................................................... 5,5 l/minCoil resistance ................................................ 4300 ohm

CYCLING PUMP :Delivery rate ...................................................... 12 l/minPower absorbed ..................................................... 18 WWinding resistance ........................................... 200 ohm

DOOR INTERLOCK :Type.................................................................voltmetricInternal door locking .............................................. 0,02 sInternal door release .............................................. 0,02 s

DOOR INTERLOCK :Type.................................................................voltmetricInternal door locking .................................................. 6 sInternal door release .......................................... 40-120 s

WATERSAFETY SYSTEM :Type ................................................................. 110539000

TEMPERATURE PROBE (NTC) ................ 6 kohm at 20C

PRESSURE SWITCH ANALOGIC :Analogic Level ....................................... 000 mm - 44,7 HzAnalogic Level ....................................... 300 mm - 36,1 Hz

USER INTERFACE : EWM2100Indentification mark ............................................ 13254160.Indentification mark ............................................ 13254161.Indentification mark ............................................ 13254162.Indentification mark ............................................ 13254163.

USER INTERFACE : EWM2500Indentification mark ............................................ 13254172.Indentification mark ............................................ 13254173.Indentification mark ............................................ 13254174.

MODULE REGULATION SPEED : EWM2500Module ................................................................ 13252771.Supply voltage ............................................................ 230 V

DOOR POSITIONNING (electric):Indentification mark ......................................... 146132000

DISPLAY LCD :Serie 6-low .......................................................... 13254441.Serie 6 ........................................................ ........13252918.Serie 7 ................................................................. 13252916.Serie 7-hight ........................................................ 13252903.Serie 8 ................................................................. 13254430.

CONNECTION :Water supply connection ................................... 1,5 m longWater discharge connection height ........ mini 70 / maxi 100 cmTotal power ........................................................... 2300 W


COLLECTOR MOTOR :Pulley ratio ..................................................................10,2Insulation class ............................................................... FSpinning speed ................................................. 1450 r.p.mWinding resistance (1-2) ..................................... 5,44 ohmWinding resistance (3-2) ..................................... 5,44 ohmWinding resistance (1-3) ..................................... 5,44 ohmTACHOGENERATOR :Resistance (5-4) ................................................... 115 ohm

Pulley ratio ..................................................................10,4Insulation class ............................................................ B/FSpinning speed ................................................. 1450 r.p.mWinding resistance (3-4) ..................................... 2,20 ohmWinding resistance (1-2-5) .................................. 0,55 ohmWinding resistance (2-5) ..................................... 1,10 ohmTACHOGENERATOR :Resistance (6-7) ................................................... 135 ohm

Pulley ratio ..................................................................10,4Insulation class ............................................................ B/FSpinning speed ................................................. 1450 r.p.mWinding resistance (3-4) ..................................... 1,78 ohmWinding resistance (1-2-5) .................................. 0,60 ohmWinding resistance (2-5) ..................................... 1,75 ohmTACHOGENERATOR :Resistance (6-7) .................................................. 68,7 ohm

Pulley ratio .....................................................................12Insulation class ............................................................ B/FSpinning speed ................................................. 1250 r.p.mWinding resistance (3-4) ..................................... 1,73 ohmWinding resistance (1-2-5) .................................. 1,10 ohmWinding resistance (2-5) ..................................... 1,70 ohmTACHOGENERATOR :Resistance (6-7) .................................................. 15,1 ohm

Pulley ratio .....................................................................12Insulation class ............................................................ B/FSpinning speed ................................................. 1250 r.p.mWinding resistance (3-4) ..................................... 1,65 ohmWinding resistance (1-2-5) .................................. 0,62 ohmWinding resistance (2-5) ..................................... 1,23 ohmTACHOGENERATOR :Resistance (6-7) ................................................... 135 ohm

Pulley ratio .....................................................................12Insulation class ............................................................ B/FSpinning speed ................................................. 1150 r.p.mWinding resistance (3-4) ..................................... 1,90 ohmWinding resistance (2-5) ..................................... 1,30 ohmTACHOGENERATOR :Resistance (6-7) .................................................. 68,7 ohm

Pulley ratio .....................................................................14Insulation class ............................................................B/FSpinning speed ................................................. 1050 r.p.mWinding resistance (3-4) ..................................... 1,62 ohmWinding resistance (2-5) ..................................... 1,67 ohmTACHOGENERATOR :Resistance (6-7) .................................................. 15,1 ohm

Pulley ratio .....................................................................14Insulation class ............................................................B/FSpinning speed ................................................. 1050 r.p.mWinding resistance (3-4) ..................................... 2,46 ohmWinding resistance (2-5) ..................................... 1,86 ohmTACHOGENERATOR :Resistance (6-7) .................................................. 68,7 ohm

Pulley ratio .....................................................................18Insulation class ............................................................B/FSpinning speed ...................................................850 r.p.mWinding resistance (3-4) ..................................... 1,62 ohmWinding resistance (2-5) ..................................... 1,67 ohmTACHOGENERATOR :Resistance (6-7) .................................................. 15,1 ohm



ASYNCHRONOUS THREE-PHASE MOTOR :Pulley ratio .....................................................................12Insulation class ............................................................... FSpinning speed ............................................... 17000 r.p.mWinding resistance X (4-5) .................................... 5,5 ohmWinding resistance Z (4-6) .................................... 5,5 ohmWinding resistance Y (5-6) .................................... 5,5 ohmTACHOGENERATOR :Resistance (7-8) .................................................... 119ohm

- 51 -DGS-TDS-N 10.07 R.B. Electrolu

Date post:	12-Oct-2015
Category:	Documents
Upload:	niknak68
View:	37 times
Download:	0 times

aeg_ewm_2500_2100

Documents