E5071C ENA Network Analyzer • 9kHzto4.5/6.5/8.5GHz • 100kHzto4.5/6.5/8.5GHz(withbiastees) • 300kHzto14/20GHz(withbiastees)
E5092A Configurable Multiport Test Set
Agilent
DataSheet
2
Table of ContentsOptions ....................................................................................................................... 3
Definitions................................................................................................................. 4Boundary Conditions............................................................................................. 4Corrected System Performance ...................................................................... 5 Systemdynamicrange........................................................................................... 5 Correctedsystemperformancewithcalibrationkit .............................................7
Uncorrected System Performance................................................................13Test Port Output (Source).................................................................................14 Testportoutputfrequency ..................................................................................14 Testportoutputpower ........................................................................................15 Testportoutputsignalpurity...............................................................................17
Test Port Input ......................................................................................................18 Testportinputlevels ...........................................................................................18 Testportinput(compression)..............................................................................20 Testportinput(tracenoise)................................................................................21 Testportinput(stability) .....................................................................................23 Testportinput(dynamicaccuracy).....................................................................24 Testportinput(groupdelay)...............................................................................26
General Information ...........................................................................................28 Systembandwidths .............................................................................................28 Frontpanelinformation .......................................................................................28 Rearpanelinformation ........................................................................................29 LXIcompliance ....................................................................................................31 EMC,safetyandenvironment .............................................................................32 Analyzerenvironmentalspecificationsanddimensions.....................................33
Measurement Throughput Summary ..........................................................37 Cycletimeformeasurementcompletion(ms)...................................................37 Cycletime(ms)vs.numberofpoints.................................................................42 Cycletime(ms)vs.IFbandwidth........................................................................43 CycleTime(ms)vsRFRangeFixedMode.........................................................44 Datatransfertime(ms).......................................................................................45
E5092A Configurable Multiport Test Set ....................................................46 Testsetinput/outputperformance .....................................................................46 OptionE5092A-020portperformance..................................................................46 Controlline...........................................................................................................48 DCsource.............................................................................................................48 Operatingstorageenvironment..........................................................................48 Non-operatingstorageenvironment...................................................................48 Frontpanelinformation.......................................................................................49 Rearpanelinformation........................................................................................49 Testsetdimensionsandblockdiagram..............................................................49
Corrected System Performance for 75 Ω Measurements with 11852B 50 to 75 Ω Minimum-Loss Pads .........................................53
3
OptionsThisdocumentprovidestechnicalspecificationsfortheE5071CENAnetworkanalyzerandtheE5092Amultiporttestset.
E5071C-230 2-porttestset,9kHzto3GHzwithoutbiastees(Discontinued)E5071C-235 2-porttestset,100kHzto3GHzwithbiastees(Discontinued)E5071C-240 2-porttestset,9kHzto4.5GHzwithoutbiasteesE5071C-245 2-porttestset,100kHzto4.5GHzwithbiasteesE5071C-260 2-porttestset,9kHzto6.5GHzwithoutbiasteesE5071C-265 2-porttestset,100kHzto6.5GHzwithbiasteesE5071C-280 2-porttestset,9kHzto8.5GHzwithoutbiasteesE5071C-285 2-porttestset,100kHzto8.5GHzwithbiasteesE5071C-430 4-porttestset,9kHzto3GHzwithoutbiastees(Discontinued)E5071C-435 4-porttestset,100kHzto3GHzwithbiastees(Discontinued)E5071C-440 4-porttestset,9kHzto4.5GHzwithoutbiasteesE5071C-445 4-porttestset,100kHzto4.5GHzwithbiasteesE5071C-460 4-porttestset,9kHzto6.5GHzwithoutbiasteesE5071C-465 4-porttestset,100kHzto6.5GHzwithbiasteesE5071C-480 4-porttestset,9kHzto8.5GHzwithoutbiasteesE5071C-485 4-porttestset,100kHzto8.5GHzwithbiasteesE5071C-2D5 2-porttestset,300kHzto14GHzwithbiasteesE5071C-4D5 4-porttestset,300kHzto14GHzwithbiasteesE5071C-2K5 2-porttestset,300kHzto20GHzwithbiasteesE5071C-4K5 4-porttestset,300kHzto20GHzwithbiasteesE5092A Configurablemultiporttestset
Calibration kits and ECal modulesThisE5071CdatasheetalsoprovidestechnicalspecificationsforthefollowingcalibrationkitsandECalmodules.Formodelsnotlistedinthisdatasheet,pleasedownloadthefreeUncertaintyCalculatorfromwww.agilent.com/find/na_calculatortogeneratethecurvesforyourcalibrationkit.
85032F Calibrationkit85033E Calibrationkit85052D Calibrationkit85092C Electroniccalibration(ECal)module85093C Electroniccalibration(ECal)moduleN4691B Electroniccalibration(ECal)module
4
DefinitionsSpecification (spec.): Warrantedperformance.Allspecificationsapplyat23ºC(±5ºC),unlessotherwisestated,and90minutesaftertheinstrumenthasbeenturnedon.Specificationsincludeguardbandstoaccountfortheexpectedstatisticalperformancedistribution,measurementuncertainties,andchangesinperformanceduetoenvironmentalconditions.
Supplementalinformationisintendedtoprovideinformationthatishelpfulforusingtheinstrumentbutthatisnotguaranteedbytheproductwarranty.
Typical (typ.): Describesperformancethatwillbemetbyaminimumof80%ofallproducts.Itisnotguaranteedbytheproductwarranty.
Supplemental performance data (SPD): Supplementalperformancedatarepresentsthevalueofaparameterthatis mostlikelytooccur;theexpectedmeanoraverage.Itisnotguaranteedbytheproductwarranty.
General characteristics: Ageneral,descriptivetermthatdoesnotimplyalevelofperformance.
Note:ThespecificationsinthisdatasheetalsoapplytotheE5071CEPENAnetworkanalyzerexpressconfiguration.FormoreinformationabouttheExpressENA,visitwww.agilent.com/find/express-e5071c
Boundary ConditionsInthisdatasheet,boundaryconditionsaregivenforthespecifications.Forexample,systemdynamicrangeis98dBwiththefollowingboundaryconditions.
Option: 485 Frequency: 10MHz IF bandwidth:3kHz
Ifthesameboundaryconditionsfallundermorethanonecategoryinatable,applythebestvalue.
5
Corrected System PerformanceThespecificationsinthissectionapplytomeasurementsmadewiththeAgilentE5071Cnetworkanalyzerunderthefollowingconditions:• Noaveragingappliedtodata• Environmentaltemperatureof23°C(±5°C)withlessthan1°Cdeviation fromthecalibrationtemperature• Responseandisolationcalibrationperformed• RFRangeFixedMode:OFF
System dynamic range
Table 1. Option230/235/240/245/260/265/280/285/430/435/440/445/460/465/480/485Description Specification SPDSystem dynamic range1, 2, 3
9kHzto300kHz 72dB300kHzto10MHz IFbandwidth=3kHz 82dB10MHzto6GHz 98dB6GHzto8.5GHz 92dB
9kHzto300kHz 97dB 115dB300kHzto10MHz 107dB 115dB10MHzto6GHz IFbandwidth=10Hz 123dB 130dB6GHzto7GHz 117dB 128dB7GHzto8GHz 117dB 126dB8GHzto8.5GHz 117dB 124dB
Figure 1. System dynamic range (specification and actual measurement data example, IF bandwidth 10 Hz)
80
90
100
110
120
130
140
150
160
1.E+05 1.E+09 2.E+09 3.E+09 4.E+09 5.E+09 6.E+09 7.E+09 8.E+09
Test frequency [Hz]
Syst
em d
ynam
ic ra
nge
[dB]
E5071C specification
1. Thetestportdynamicrangeiscalculatedasthedifferencebetweenthetestportrmsnoisefloor andthesourcemaximumoutputpower.Theeffectivedynamicrangemusttakemeasurement uncertaintyandinterferingsignalsintoaccount.2. Thespecificationmightnotbemetat5MHzor50MHz.3. SystemDynamicRangemaybedegradedby10dBwhenRFRangeFixedModeisON.
6
System dynamic range (continued)
Table 2.Option2D5/2K5/4D5/4K5
Description Specification SPDSystem dynamic range1, 2
300kHzto1MHz
IFbandwidth=3kHz
70dB
1MHzto10MHz 82dB10MHzto100MHz 95dB100MHzto6GHz 98dB6GHzto8.5GHz 92dB8.5GHzto10.5GHz 80dB10.5GHzto15GHz 75dB15GHzto20GHz 71dB300kHzto1MHz
IFbandwidth=10Hz
95dB 105dB1MHzto10MHz 107dB 115dB
10MHzto100MHz 120dB 129dB100MHzto6GHz 123dB 130dB6GHzto8GHz 117dB 129dB8GHzto8.5GHz 117dB 127dB8.5GHzto10.5GHz 105dB 115dB10.5GHzto15GHz 100dB 111dB15GHzto20GHz 96dB 105dB
Figure 2. System dynamic range (specification and actual measurement data example, IF bandwidth 10 Hz)
1. Thetestportdynamicrangeiscalculatedasthedifferencebetweenthetestport’srmsnoise floorandthesource’smaximumoutputpower.Effectivedynamicrangemusttakemeasurement uncertaintyandinterferingsignalsintoaccount.2. Thespecificationmightnotbemetat5MHzor50MHz.
Frequency [Hz]
Syst
em dy
nam
ic ra
nge[
dB]
E5071C-2D5/2K5/4D5/4K5 specification
0.0E+00 5.0E+09 1.0E+10 1.5E+10 2.0E+1080
90
100
110
120
130
140
150
160
7
Corrected system performance with calibration kit
Option 230/235/240/245/260/265/280/285/430/435/440/445/460/465/480/485
Table 3. Correctedsystemperformancewithtype-Ndeviceconnectors,85032FcalibrationkitNetwork analyzer: E5071C Calibration kit: 85032F (Type-N, 50 Ω)Calibration: full 2-port
IF bandwidth = 10 Hz, no averaging applied to data, environmental temperature = 23 °C (±5 °C ) with < 1 °C deviation from calibration temperature, isolation calibration performed
Description
Specification (dB)9 kHz to 300 kHz
300 kHz to 10 MHz
10 MHz to 3 GHz
3 GHz to 6 GHz
6 GHz to 8.5 GHz
Directivity 49 49 46 40 38Sourcematch 41 41 40 36 35Loadmatch 49 49 46 40 37Reflectiontracking ±0.011 ±0.011 ±0.021 ±0.032 ±0.054Transmissiontracking ±0.027 ±0.015 ±0.018 ±0.056 ±0.088
Transmission uncertainty (specification)
Reflection uncertainty (specification)
8
Table 4.Correctedsystemperformancewithtype-Ndeviceconnectors,85092Celectroniccalibration(ECal)module
Network analyzer: E5071CCalibration module: 85092C (Type-N, 50 Ω) Electronic calibration (ECal) moduleCalibration: full 2-port
IF bandwidth = 10 Hz, no averaging applied to data, environmental temperature = 23 °C (±5 °C ) with < 1 °C deviation from calibration temperature , isolation calibration is not performed
Description
Specification (dB)300 kHz to 10 MHz
10 MHz to 3 GHz
3 GHz to 6 GHz
6 GHz to 8.5 GHz
Directivity 45 54 52 47Sourcematch 36 44 41 36Loadmatch 41 47 44 39Reflectiontracking ±0.100 ±0.040 ±0.060 ±0.070Transmissiontracking ±0.055 ±0.039 ±0.068 ±0.136
Transmission uncertainty (specification)
Reflection uncertainty (specification)
9
Table 5.Correctedsystemperformancewith3.5mmdeviceconnectortype,85033Ecalibrationkit Network analyzer: E5071CCalibration kit: 85033E (3.5 mm, 50 Ω)Calibration: full 2-port
IF bandwidth = 10 Hz, no averaging applied to data, environmental temperature = 23 °C (±5 °C ) with < 1 °C deviation from calibration temperature, isolation calibration performed
Description
Specification (dB)9 kHz to 300 kHz
300 kHz to 10 MHz
10 MHz to 3 GHz
3 GHz to 6 GHz
6 GHz to 8.5 GHz
Directivity 46 46 44 38 38Sourcematch 43 43 40 37 36Loadmatch 46 46 44 38 38Reflectiontracking ±0.006 ±0.006 ±0.007 ±0.009 ±0.010Transmissiontracking ±0.026 ±0.015 ±0.020 ±0.058 ±0.079
Transmission uncertainty (specification)
Reflection uncertainty (specification)
10
Table 6. Correctedsystemperformancewith3.5mmdeviceconnectortype,85093Celectroniccalibration(ECal)module
Network analyzer: E5071CCalibration module: 85093C (3.5 mm, 50 Ω) electronic calibration (ECal) moduleCalibration: full 2-port
IF bandwidth = 10 Hz, no averaging applied to data, environmental temperature = 23 °C (±5 °C ) with < 1 °C deviation from calibration temperature, isolation calibration is not performed
Description
Specification (dB)300 kHz to 10 MHz
10 MHz to 3 GHz
3 GHz to 6 GHz
6 GHz to 8.5 GHz
Directivity 45 52 51 47Sourcematch 36 44 39 34Loadmatch 41 47 44 40Reflectiontracking ±0.100 ±0.040 ±0.050 ±0.070Transmissiontracking ±0.055 ±0.049 ±0.068 ±0.117
Transmission uncertainty (specification)
Reflection uncertainty (specification)
11
Option 2D5/2K5/4D5/4K5
Table 7. Correctedsystemperformancewith3.5mmdeviceconnectors,85052Dcalibrationkit
Network analyzer: E5071C Calibration kit: 85052D (3.5 mm, 50 Ω)Calibration: full 2-port
IF bandwidth = 10 Hz, no averaging applied to data, environmental temperature = 23 °C (±5 °C ) with < 1 °C deviation from calibration temperature, isolation calibration performed
Description
Specification (dB)300 kHz to 500 MHz
500 MHz to 2 GHz
2 GHz to 6 GHz
6 GHz to 20 GHz
Directivity 42 42 38 36Sourcematch 37 37 31 28Loadmatch 42 42 38 36Reflectiontracking ±0.003 ±0.003 ±0.004 ±0.008Transmissiontracking ±0.068 ±0.034 ±0.100 ±0.208
Transmission uncertainty (specification)
Reflection uncertainty (specification)
0 .01
0 .1
1
10
-90-80-70-60-50-40-30-20-10010
3 0 0 K Hz to 5 0 0 M Hz5 0 0 M Hz to 2 G Hz2 G Hz to 6 G Hz6 G Hz to 2 0 G Hz
S11 = S22 = 0; Cal power = -10 dBm; Meas power = -10 dBm
Unc
erta
inty
(dB
)
Transmission Coefficient (dB)
Magnitude
0 .1
1
10
100
-90-80-70-60-50-40-30-20-10010
3 0 0 K Hz to 5 0 0 M Hz
5 0 0 M Hz to 2 G Hz
2 G Hz to 6 G Hz
6 G Hz to 2 0 G Hz
S11 = S22 = 0; Cal power = -10 dBm; Meas power = -10 dBm
Phase
Unce
rtain
ty (D
egre
es)
T rans mis s ion C oeffic ient (dB )
0
0 .01
0 .02
0 .03
0 .04
0 .05
0 0 .2 0 .4 0 .6 0 .8 1
Unce
rtain
ty (li
near
)
Reflection coefficient (linear)
Magnitude
3 0 0 K Hz to 5 0 0 MHz, 5 0 0 MHz to 2 G Hz
2 G Hz to 6 G Hz
6 G Hz to 2 0 G Hz
S2 1 = S1 2 = 0 ; Cal power = -10 dBm; Meas power = -10 dBm0
2
4
6
8
10
0 0 .2 0 .4 0 .6 0 .8 1
Unce
rtain
ty (d
egre
es)
Reflection coefficient (linear)
Phase
3 0 0 K Hz to 5 0 0 MHz, 5 0 0 MHz to 2 G Hz
2 G Hz to 6 G Hz
6 G Hz to 2 0 G Hz
S2 1 = S1 2 = 0 ; Cal power = -10 dBm; Meas power = -10 dBm
12
Table 8. Correctedsystemperformancewith3.5mmdeviceconnectors,N4691Belectroniccalibration(ECal)module Network analyzer: E5071CCalibration module: N4691B (3.5 mm, 50 Ω) electronic calibration (ECal) moduleCalibration: full 2-port
IF bandwidth = 10 Hz, no averaging applied to data, environmental temperature = 23 °C (±5 °C ) with < 1 °C deviation from calibration temperature, isolation calibration is not performed
Description
Specification (dB)10 MHz to 500 MHz
500 MHz to 2 GHz
2 GHz to6 GHz
6 GHz to 20 GHz
Directivity 46 56 54 48Sourcematch 41 47 45 44Loadmatch 38 41 39 36Reflectiontracking ±0.050 ±0.020 ±0.030 ±0.040Transmissiontracking ±0.087 ±0.086 ±0.097 ±0.130
Transmission uncertainty (specification)
Reflection uncertainty (specification)
0
0 .01
0 .02
0 .03
0 .04
0 .05
0 0 .2 0 .4 0 .6 0 .8 1
Unce
rtain
ty (li
near
)
Reflection coefficient (linear)
Magnitude
1 0 MHz to 5 0 0 MHz
5 0 0 MHz to 2 G Hz
2 G Hz to 6 G Hz
6 G Hz to 2 0 G Hz
S2 1 = S1 2 = 0 ; Cal power = -10 dBm; Meas power = -10 dBm
0
2
4
6
8
10
0 0 .2 0 .4 0 .6 0 .8 1
Unce
rtain
ty (d
egre
es)
Reflection coefficient (linear)
Phase
1 0 MHz to 5 0 0 MHz5 0 0 MHz to 2 G Hz2 G Hz to 6 G Hz6 G Hz to 2 0 G Hz
S2 1 = S1 2 = 0 ; Cal power = -10 dBm; Meas power = -10 dBm
1 0 M Hz to 5 0 0 M Hz5 0 0 M Hz to 2 G Hz2 G Hz to 6 G Hz6 G Hz to 2 0 G Hz
S 11 = S 22 = 0 ; Cal power = -10 dBm; Meas power = -10dBm0 .01
0 .1
1
10
-90-80-70-60-50-40-30-20-10010
Unce
rtain
ty (d
B)
Transmission coefficient (dB)
Magnitude
1 0 M Hz to 5 0 0 M Hz5 0 0 M Hz to 2 G Hz2 G Hz to 6 G Hz6 G Hz to 2 0 G Hz
S 11 = S 22 = 0 ; Cal power = -10 dBm; Meas power = -10dBm0 .1
1
10
100
-90-80-70-60-50-40-30-20-10010
Unce
rtain
ty (D
egre
es)
Transmission coefficient (dB)
Phase
13
Uncorrected System Performance1
Table 9. Option230/235/240/245/260/265/280/285/430/435/440/445/460/465/480/485
User correction: OFF, system correction: ON
Description
Specification (dB)9 kHz to 300 kHz
300 kHz to 3 GHz
3 GHz to 6 GHz
6 GHzto 8.5 GHz
Directivity 20dB 25dB 20dB 15dBSourcematch 20dB 25dB 20dB 15dBLoadmatch2 12dB 17dB 12dB 10dBTransmissiontracking3 ±1.5dB ±1.0dB ±1.0dB ±1.0dBReflectiontracking ±1.5dB ±1.0dB ±1.0dB ±1.0dB
Table 10. Option2D5/2K5/4D5/4K5
User correction: OFF, system correction: ON
Description
Specification (dB)300 kHz to 1 MHz
1 MHz to 1 GHz
1 GHz to 3 GHz
3 GHz to6 GHz
6 GHz to 8.5 GHz
8.5 GHz to 11 GHz
11 GHz to 20 GHz
Directivity 20dB 25dB 25dB 20dB 15dB 15dB 15dBSourcematch 20dB 25dB 25dB 20dB 15dB 15dB 15dBLoadmatch 9dB 17dB 15dB 11dB 9dB 8dB 7dBTransmissiontracking
±1.0dB ±1.0dB ±1.0dB ±1.0dB ±1.0dB ±1.0dB ±1.0dB
Reflectiontracking
±1.0dB ±1.0dB ±1.0dB ±1.0dB ±1.0dB ±1.0dB ±1.0dB
1. ThespecificationmightnotbemetwhenShiftLOModeisON.2. Loadmatchmaybedegradedby3dBwhenRFRangeFixedModeisON.3. Transmissiontrackingmaybedegradedby±4dBwhenRFRangeFixedModeisON.
14
Test Port Output (Source)Test port output frequency
Table 11. Option230/235/240/245/260/265/280/285/430/435/440/445/460/465/480/485/2D5/2K5/4D5/4K5
Description Specification TypicalFrequencyrangeOption230/430 Option240/440Option260/460 Option280/480 Option235/435 Option245/445Option265/465 Option285/485Option2D5/4D5 Option2K5/4K5
9kHzto3GHz 9kHzto4.5GHz9kHzto6.5GHz 9kHzto8.5GHz 100kHzto3GHz 100kHzto4.5GHz100kHzto6.5GHz 100kHzto8.5GHz300kHzto14GHz 300kHzto20GHz
Resolution 1Hz
SourcestabilitystandardOption1E5
±7ppm(5to40ºC) ±0.05ppm(5to40ºC),±0.5ppm/year
CWaccuracystandardOption1E5
±7ppm±0.45ppm(SerialNumberPrefixMY463/SG463andabove)±1ppm(SerialNumberPrefixMY462/SG462andbelow)
15
Test port output power1
Table 12.Option230/235/240/245/260/265/280/285/430/435/440/445/460/465/480/485
Description Specification TypicalNominalpower (presetpower) 0dBm
Levelaccuracy2,6 (steppedsweepmode)
±0.650dB(at0dBm,50MHzabsolute) ±1.0dB
Levelaccuracy2 (sweptsweepmode) ±2.5dB
Levellinearity3,5,6 (steppedsweepmode) 9kHzto5GHz 5GHzto6GHz 6GHzto7GHz 7GHzto8.5GHz
±0.75dB(–20to10dBm) ±0.75dB(–20to9dBm) ±0.75dB(–20to8dBm) ±0.75dB(–20to7dBm)
Levellinearity5(sweptsweepmode)4 9kHzto5GHz 5GHzto6GHz 6GHzto7GHz 7GHzto8.5GHz
±1.5dB(at–20to10dBm) ±1.5dB(at–20to9dBm) ±1.5dB(at–20to8dBm) ±1.5dB(at–20to7dBm)
Range5,6 9kHzto5GHz 5GHzto6GHz 6GHzto7GHz 7GHzto8.5GHz
–55to10dBm –55to9dBm –55to8dBm –55to7dBm
Sweeprange5,6 9kHzto5GHz 5GHzto6GHz6GHzto7GHz7GHzto8.5GHz
–55to10dBm –55to9dBm –55to8dBm –55to7dBm
Levelresolution 0.05dB
Description Specification SPDMaxleveledpower5,6 (Option230/235/240/245/260/ 265/280/285) 9kHzto8.5GHz
(Option430/435/440/445/460/ 465/480/485) 9kHzto6GHz 6GHzto7GHz 7GHzto8.5GHz
10dBm
10dBm 9dBm 8dBm
1. Sourceoutputperformanceonport1only.Otherportoutputperformanceistypical.2. Levelaccuracyistakenat0dBm,relativeto50MHzreferenceunlessotherwisestated.3. Levellinearitygivenisrelativeto0dBm.4. Thespecificationmightnotbemetat5MHzor50MHz.5. Thelevelaccuracyspecificationneedstobetakenintoaccountfortestportoutputpowerlevel.6. Powercalibrationusinganexternalpowermeterimproveslevelaccuracyofthetestportoutputpower. Properpowermeters/sensors,andthe82357BUSB-GPIBinterfacearerequiredtoconductpowercalibration.
16
Test port output power7 (continued)
Table 13. Option2D5/2K5/4D5/4K5Description Specification TypicalNominalpower(presetpower) –5dBmLevelaccuracy6 (steppedsweepmode)1 300kHzto1MHz1MHzto5MHz 5MHzto8.5GHz 8.5GHzto20GHz
±0.650dB(at–5dBm,50MHzabsolute) +2.0dB,–6.0dB±2.0dB ±1.0dB ±2.5dB
Levelaccuracy(sweptsweepmode)2300kHzto1GHz 1GHzto8.5GHz 8.5GHzto20GHz
±5.0dB ±2.5dB +5.0dB,–7.0dB
Levellinearity5,6 (steppedsweepmode)3 300kHzto1MHz 1MHzto6GHz 6GHzto8GHz 8GHzto10.5GHz10.5GHzto15GHz 15GHzto20GHz
±0.75dB(–25to8dBm) ±0.75dB(–25to10dBm) ±0.75dB(–25to9dBm) ±0.75dB(–25to7dBm) ±0.75dB(–25to3dBm)±0.75dB(–25to0dBm)
Levellinearity5 (sweptsweepmode)3 300kHzto1MHz 1MHzto6GHz 6GHzto8GHz 8GHzto10.5GHz 10.5GHzto15GHz 15GHzto20GHz
±1.5dB(–25to8dBm) ±1.5dB(–25to10dBm) ±1.5dB(–25to9dBm) ±1.5dB(–25to7dBm) ±1.5dB(–25to3dBm) ±1.5dB(–25to0dBm)
Range5,6 300kHzto1MHz 1MHzto6GHz 6GHzto8GHz 8GHzto10.5GHz 10.5GHzto15GHz 15GHzto20GHz
–85to8dBm –85to10dBm –85to9dBm –85to7dBm –85to3dBm –85to0dBm
Sweeprange4,5,6 300kHzto1MHz 1MHzto6GHz 6GHzto8GHz 8GHzto10.5GHz 10.5GHzto15GHz 15GHzto20GHz(Sourceattenuator=0dB)
–25to8dBm –25to10dBm –25to9dBm –25to7dBm –25to3dBm –25to0dBm
Levelresolution 0.05dB
1. Levelaccuracyistakenat–5dBm,relativeto50MHzreferenceunlessotherwisestated.2. Levelaccuracyistakenat–5dBm,relativeto50MHzreference.3. Levellinearitygivenisrelativeto–5dBm.4. Thesweeprangeshiftsbasedontheselectedsourceattenuatorvalue(0dBto60dB,10dBstep).5. Thelevelaccuracyspecificationneedstobetakenintoaccountfortestportoutputpowerlevel.6. Powercalibrationusinganexternalpowermeterimproveslevelaccuracyofthetestportoutputpower. Properpowermeters/sensors,andthe82357BUSB-GPIBinterfacearerequiredtoconductpowercalibration.7. Sourceoutputperformanceonport1only.Otherportoutputperformanceistypical.
17
Test port output power6 (continued)
Table 13. Option2D5/2K5/4D5/4K5
Description Specification SPDMaxleveledpower3,4300kHzto1MHz 1MHzto10GHz 10GHzto13GHz 13GHzto15GHz 15GHzto18GHz 18GHzto20GHz
9dBm10dBm 9dBm 7dBm 5dBm 4dBm
Test port output signal purity
Table 14.Option230/235/240/245/260/265/280/285/430/435/440/445/460/465/480/485
Description Specification TypicalHarmonics(2ndor3rd) 9kHzto2GHz 2GHzto8.5GHz
<–25dBc(at5dBm) <–20dBc(at5dBm)
Non-harmonicspurious9kHzto8.5GHz
<–30dBc(at5dBm)
Table 15. Option2D5/2K5/4D5/4K5
Description Specification TypicalHarmonics(2ndto5th)1 300kHzto1GHz 1GHzto20GHz
< –12dBc(atmaximumoutputpower)5 < –15dBc(atmaximumoutputpower)5
Non-harmonicspurious2 300kHzto20GHz
< –30dBc(at–5dBm)
1. Thisincludes6thand7thharmonicswhenthetestfrequencyisfrom1MHzto1GHz.2. Thecarrier±1/8thspuriousisexcludedfrom8.76GHzto17.52GHz.3. Thelevelaccuracyspecificationneedstobetakenintoaccountfortestportoutputpowerlevel.4. Powercalibrationusinganexternalpowermeterimproveslevelaccuracyofthetestportoutputpower. Properpowermeters/sensors,andthe82357BUSB-GPIBinterfacearerequiredtoconductpowercalibration.5. Maximumoutputpoweristhemaximumpowerof"Range"inTable13Testportoutputpower.6. Sourceoutputperformanceonport1only.Otherportoutputperformanceistypical.
18
Test Port Input
Test port input levels
Table 16. Option230/235/240/245/260/265/280/285/430/435/440/445/460/465/480/485
Description Specification TypicalMaximum test port input level
9kHzto8.5GHz +10dBmDamage level9kHzto8.5GHz +26dBm
±35VDCCrosstalk1, 2
9kHzto300kHz 300kHzto10MHz 10MHzto3GHz 3GHzto6GHz 6GHzto8.5GHz
–100dB –110dB –120dB –110dB –100dB
Description Specification SPDTest port noise floor3
9kHzto300kHz300kHzto10MHz10MHzto5GHz5GHzto6GHz6GHzto7GHz7GHzto8GHz8GHzto8.5GHz
–97dBm/Hz–107dBm/Hz–123dBm/Hz–124dBm/Hz–119dBm/Hz–120dBm/Hz–120dBm/Hz
–115dBm/Hz–115dBm/Hz–130dBm/Hz–131dBm/Hz–130dBm/Hz–129dBm/Hz–127dBm/Hz
1. Thespecificationmightnotbemetat5MHzor50MHz.2. Crosstalkmaybedegradedby10dBwhenRFRangeFixedModeisON.3. Testportnoisefloormaybedegradedby10dBwhenRFRangeFixedModeisON.
19
Test port input levels (continued)
Table 17.Option2D5/2K5/4D5/4K5
Description Specification TypicalMaximum test port input level
300kHzto20GHz +10dBm
Damage level300kHzto20GHz +26dBm
or±35VDCCrosstalk1
300kHzto1MHz 1MHzto5MHz 5MHzto10MHz 10MHzto45MHz 45MHzto4GHz 4GHzto6GHz 6GHzto8.5GHz 8.5GHzto15GHz 15GHzto20GHz
–68dB –70dB –100dB –110dB –118dB –123dB –120dB –112dB –106dB
Description Specification SPDTest port noise floor300kHzto1MHz1MHzto10MHz10MHzto100MHz100MHzto6GHz6GHzto8GHz8GHzto8.5GHz8.5GHzto10.5GHz10.5GHzto15GHz15GHzto20GHz
–97dBm/Hz–107dBm/Hz–120dBm/Hz–123dBm/Hz–118dBm/Hz–120dBm/Hz–108dBm/Hz–107dBm/Hz–106dBm/Hz
–110dBm/Hz–115dBm/Hz–129dBm/Hz–130dBm/Hz–130dBm/Hz–130dBm/Hz–120dBm/Hz–120dBm/Hz–119dBm/Hz
1. Thespecificationmightnotbemetat5MHzor50MHz.
20
Test port input (compression level)
Table 18. Option230/235/240/245/260/265/280/285/430/435/440/ 445/460/465/480/485
Description Specification SPD
Compression levelMagnitude9kHzto5GHz 5GHzto8.5GHz(maximumtestportinputlevel=+10dBm)
0.08dB 0.1dB
Phase9kHzto3GHz3GHzto5GHz5GHzto8.5GHz(maximumtestportinputlevel=+10dBm)
0.3deg0.6deg1.0deg
Table 19. Option2D5/2K5/4D5/4K5
Description Specification SPD
Compression levelMagnitude300kHzto10MHz10MHzto10GHz10GHzto15GHz15GHzto20GHz(maximumtestportinputlevel=+10dBm)
0.3dB0.182dB0.712dB1.87dB
Phase300kHzto5GHz5GHzto10GHz10GHzto15GHz15GHzto20GHz(maximumtestportinputlevel=+10dBm)
2.3deg4.3deg17.3deg20.3deg
21
Test port input (trace noise)
Table 20. Option230/235/240/245/260/265/280/285/430/435/440/445/460/465/480/485
Description Specification3 SPD
Trace noise magnitude1
9kHzto30kHz(IFBW=3kHz) 0.004dBrms 0.001dBrms30kHzto100kHz(IFBW=3kHz) 0.003dBrms 0.001dBrms100kHzto10MHz(IFBW=3kHz) 0.003dBrms 0.0005dBrms10MHzto4.38GHz(IFBW=10kHz) 0.0005dBrms4.38GHzto8.5GHz(IFBW=10kHz) 0.0006dBrms10MHzto4.38GHz(IFBW=70kHz) 0.004dBrms
(Reflection)0.001dBrms
0.003dBrms(Transmission)
4.38GHzto5GHz(IFBW=70kHz) 0.006dBrms 0.0012dBrms5GHzto6GHz(IFBW=70kHz) 0.006dBrms 0.0012dBrms6GHzto7GHz(IFBW=70kHz) 0.006dBrms 0.0012dBrms7GHzto8.5GHz(IFBW=70kHz)(atmaximumoutputpowerlevelofsweeprange)
0.006dBrms 0.0012dBrms
Trace noise phase2
9kHzto30kHz(IFBW=3kHz) 0.035degrms30kHzto10MHz(IFBW=3kHz) 0.020degrms10MHzto4.38GHz(IFBW=70kHz) 0.035degrms4.38GHzto5GHz(IFBW=70kHz) 0.050degrms5GHzto6GHz(IFBW=70kHz) 0.050degrms6GHzto7GHz(IFBW=70kHz) 0.050degrms7GHzto8.5GHz(IFBW=70kHz) (atmaximumoutputpowerlevelofsweeprange)
0.050degrms
1. Thespecificationmightnotbemetatthefollowingfrequencies:333.333kHz,406.25kHz, 857.143kHz,928.571kHz,1.3MHz,2.4MHzand4.333333MHz.2. Thespecificationmightnotbemetat5MHzor50MHz.3. WhenRFRangeFixedModeisON,multiplyby2.3.
22
Test port input (trace noise) (continued)
Table 21.Option2D5/2K5/4D5/4K5
Description Specification SPD
Trace noise magnitude1, 3
300kHzto1MHz(IFBW=3kHz)1MHzto10MHz(IFBW=3kHz)10MHzto4.38GHz(IFBW=70kHz) 4.38GHzto8.5GHz(IFBW=70kHz) 8.5GHzto13.137GHz(IFBW=70kHz) 13.137GHzto17GHz(IFBW=70kHz) 17GHzto20GHz(IFBW=70kHz)(atmaximumoutputpowerlevelofsweeprange)
0.006dBrms0.003dBrms0.004dBrms 0.006dBrms 0.009dBrms 0.013dBrms 0.023dBrms
0.0009dBrms 0.0005dBrms 0.0010dBrms 0.0012dBrms 0.0024dBrms 0.0040dBrms 0.0065dBrms
Trace noise phase2, 3
300kHzto1MHz(IFBW=3kHz) 1MHzto10MHz(IFBW=3kHz) 10MHzto4.38GHz(IFBW=70kHz) 4.38GHzto8.5GHz(IFBW=70kHz) 8.5GHzto13.137GHz(IFBW=70kHz) 13.137GHzto17GHz(IFBW=70kHz) 17GHzto20GHz(IFBW=70kHz)(atmaximumoutputpowerlevelofsweeprange)
0.040degrms 0.020degrms 0.035degrms 0.050degrms 0.064degrms 0.095degrms 0.165degrms
0.0120degrms 0.0025degrms 0.0075degrms 0.0150degrms 0.0250degrms 0.0320degrms 0.0520degrms
1. Thespecificationmightnotbemetatthefollowingfrequencies:406.25kHz,666.667kHz, 722.222kHz,857.143kHz,928.571kHz,1.444444MHz,1.714286MHz,1.8MHz,1.857143MHz, 1.95MHz,2.4375MHz,2.571429MHz,3.714286MHz,4.8MHz,5MHz,5.416667MHz, 7.583333MHz,10MHz,10.833333MHz,12.5MHz.2. Thespecificationmightnotbemetat5MHzor50MHz.3. TracenoiseSPDisdefinedwithtransmissionmeasurementsonly.
23
Test port input (stability)1
Table 22.Option230/235/240/245/260/265/280/285/430/435/440/445/460/465/480/485
Description Specification SPDStability magnitude
9kHzto3GHz ±0.005dB/°C3GHzto6GHz ±0.01dB/°C6GHzto8.5GHz ±0.04dB/°C
Stability phase9kHzto3GHz ±0.1deg/°C3GHzto6GHz ±0.2deg/°C6GHzto8.5GHz ±0.8deg/°C
Table 23.Option2D5/2K5/4D5/4K5
Description Specification SPDStability magnitude300kHzto3GHz 3GHzto6GHz 6GHzto20GHz
±0.005dB/°C ±0.01dB/°C ±0.04dB/°C
Stability phase300kHzto3GHz 3GHzto6GHz 6GHzto20GHz
±0.1deg/°C ±0.2deg/°C ±0.8deg/°C
1. Stabilityisdefinedasaratiomeasurementatthetestport.
24
Test port input (dynamic accuracy)1, 2
Table 24.Option230/235/240/245/260/265/280/285/430/435/440/445/460/465/480/485
Accuracy of the test port input power reading is relative to –10 dBm reference input power level.Description Specification TypicalDynamic accuracy magnitude10dBm ±0.207dB–30dBm ±0.045dB–100dBm ±2.00dB–110dBm ±3.0dBDynamic accuracy phase10dBm ±5.03deg–30dBm ±0.30deg–100dBm ±15.0deg
Specification
±3.0 dB (at –110 dBm, Ref.= –10 dBm, typical)
0.01
0.1
1
10
-100-90-80-70-60-50-40-30-20-10010
Accu
racy (
dB)
Test port power (dBm)
Magnitude
Accu
racy (
deg)
Test port power (dBm)
Phase
0.1
1
10
100
-100-90-80-70-60-50-40-30-20-10010
1. Dynamicaccuracyisverifiedwiththefollowingmeasurements: • compressionoverfrequency • IFlinearityattwofrequencies(1MHzand1.195GHz)usingareferencelevelof–10dBmfor aninputpowerrangeof0to–100dBm.Forvaluebelow–60dBm,referto"VNAReceiver DynamicAccuracySpecificationsandUncertaintiesN5247-90003" http://cp.literature.agilent.com/litweb/pdf/N5247-90003.pdf2. RFRangeFixedModeisOFF
25
Test port input (dynamic accuracy)1 (continued)
Table 25. Option2D5/2K5/4D5/4K5Accuracy of the test port input power reading is relative to –10 dBm reference input power level.
Description Specification TypicalDynamic accuracy magnitude10dBm ±2.49dB–30dBm ±0.046dB–100dBm ±2.00dB–110dBm ±3.0dBDynamic accuracy phase10dBm ±20.6deg–30dBm ±0.30deg–100dBm ±15.0deg
Specification
±3.0 dB (at –110 dBm, Ref.= –10 dBm, typical)
Test port power (dBm)
Accu
racy
(dB)
Magnitude
0.01
0.1
1
10
-100-90-80-70-60-50-40-30-20-10010
Test port power (dBm)
Accu
racy
(deg
)
Phase
0.1
1
10
100
-100-90-80-70-60-50-40-30-20-10010
1. Dynamicaccuracyisverifiedwiththefollowingmeasurements: • compressionoverfrequency • IFlinearityattwofrequencies(1MHzand1.195GHz)usingareferencelevelof-10dBmfor aninputpowerrangeof0to-60dBm.Forvaluebelow-60dBm,referto"VNAReceiver DynamicAccuracySpecificationsandUncertaintiesN5247-90003" http://cp.literature.agilent.com/litweb/pdf/N5247-90003.pdf.
26
Test port input (group delay)1
Table 26.Option230/235/240/245/260/265/280/285/430/435/440/445/460/465/480/485
Description Specification Supplemental informationAperture(selectable) (frequencyspan)/(number
ofpoints-1)Maximumaperture 25%offrequencyspanMinimumdelay Limitedtomeasuringnomore
than180°ofphasechangewithintheminimumaperture.
Accuracy Seegraphbelow,typical
Thefollowinggraphshowsgroupdelayaccuracywithtype-Nconnectors,full2-portcalibrationanda10HzIFbandwidth,RFRangeFixedMode:OFF
Calibrationkit(85032F).Insertionlossisassumedtobe<2dB.
Ingeneral,thefollowingformulacanbeusedtodeterminetheaccuracy,inseconds,ofaspecificgroupdelaymeasurement:±phaseaccuracy(degrees)/[360xaperture(Hz)]
Accu
racy
(nSe
c)
Aperture (MHz)
0.01 0.1 1 10 100
100
10
1
0.1
0.01
0.001
C al pow er = -10 dBm ; M eas pow er = -10 dBm ; E lectrica l Length = 10 m
Frequency = 1 G H z
1. Groupdelayiscomputedbymeasuringthephasechangewithinaspecifiedstep (determinedbythefrequencyspanandthenumberofpointspersweep).
27
Test port input (group delay)1 (continued)
Table 27. Option2D5/2K5/4D5/4K5
Description Specification Supplemental informationAperture(selectable) (frequencyspan)/(number
ofpoints-1)Maximumaperture 25%offrequencyspanMinimumdelay Limitedtomeasuringnomore
than180°ofphasechangewithintheminimumaperture.
Accuracy Seegraphbelow,typical
Thefollowinggraphshowsgroupdelayaccuracywith3.5mm(male)connectors,full2-portcalibrationanda10HzIFbandwidth.
Calibrationkit(85052D).Insertionlossisassumedtobe<2dB.
Ingeneral,thefollowingformulacanbeusedtodeterminetheaccuracy,inseconds,ofaspecificgroupdelaymeasurement:±phaseaccuracy(degrees)/[360xaperture(Hz)]
C al pow er = -10 dBm ; M eas pow er = -10 dBm ; E lectrica l Length = 10 m
Frequency = 1 G H z
Accu
racy
(nSe
c)
Aperture (MHz)
0 .001
0 .01
0 .1
1
10
100
0.01 0 .1 1 10 100
1. Groupdelayiscomputedbymeasuringthephasechangewithinaspecifiedstep (determinedbythefrequencyspanandthenumberofpointspersweep).
28
General Information
Table 28. Systembandwidth
Description General characteristicsIFbandwidthsettingsRange 10Hzto1.5MHz
Nominalsettingsare: 10,15,20,30,40,50,70,100,150,200,300,400,500,700,1k,1.5k,2k,3k,4k,5k,7k,10k,15k,20k,30k,40k,50k,70k,100k,150k,200k,300k,400k,500kHz,700kHz,1MHz, 1.5MHz
Table 29. Frontpanelinformation
Description Typical General characteristicsRF connectorsOption230/235/240/245/260/265/280/285/430/435/440/445/460/465/480/485 Option2D5/2K5/4D5/4K5
Type-N,female,50Ω
3.5mm(male),50ΩnominalProbe powerConnector 3terminalconnectorx2Voltage&maximumcurrent
+15V±2%(400mA) –12.6V±5%(300mA) (Combinedloadforbothprobeconnections)
DisplayType 10.4inTFTcolorLCD
withtouchscreenResolution XGA(1024x768)1
1. Validpixelsare99.99%andmore.Below0.01%(approx.30points)offixedpointsofblack, blue,greenorredarenotregardedasfailure.
29
Table 30. Rearpanelinformation
Description Typical General characteristicsExternal trigger input connectorType BNC,female
Inputlevel Lowthresholdvoltage:0.5VHighthresholdvoltage:2.1VInputlevelrange:0to+5V
Pulsewidth ≥2μsecPolarity Positiveornegative
External trigger output connectorType BNC,femaleMaximumoutputcurrent 50mAOutputlevel Lowlevelvoltage:0V
Highlevelvoltage:5VPulsewidth 1μsecPolarity PositiveornegativeExternal reference signal input connector
Type BNC,femaleInputfrequency 10MHz±10ppmInputlevel –3to+10dBm
Internal reference signal output connectorType BNC,femaleOutputfrequency 10MHz±7ppmSignaltype SinewaveOutputlevel 0dBm±3dBinto50ΩOutputimpedance 50Ω
Internal reference signal oven connectorType BNC,femaleOutputfrequency 10MHz±1ppmOutputlevel 0dBmminimum
30
Table 31. Rearpanelinformation (continued)
Description Typical General characteristicsBias tee input connectorType BNC,female(foreachport)Maximumvoltage ±35VDCMaximumcurrent(nodegradationinRFspecifications) ±200mAMaximumcurrent(damagelevel) ±500mA
Fuse 500mA,bi-pinstyle
Video output 15-pinminiD-Sub;female;drivesXGAcompatiblemonitors
GPIB 24-pinD-Sub(TypeD-24),female;compatiblewithIEEE-488interfacespeci-ficationisdesignedtobeusedinenvironmentwhereelectricalnoiseisrelativelylow.LANorUSBTMCinter-faceisrecommendedtouseatthehigherelectricalnoiseenvironment.
USB-host portUniversalserialbusjack,TypeAconfiguration(4contactsinline,contact1onleft);female;providesconnectiontoprinter,ECalmodule,USB/GPIBinterfaceormultiporttestset
Contact1 Vcc:4.75to5.25VDC,500mA,maximum
Contact2 –DataContact3 +DataContact4 GroundUSB (USBTMC1) interface port
Universalserialbusjack,TypeBconfiguration(4contactsinline);female;providesconnectiontoanexternalPC;compatiblewithUSBTMC-USB488andUSB2.0.
LAN 10/100/1000BaseTEther-net,8-pinconfiguration;autoselectsbetweenthetwodatarates
Handler I/O port 36-pincentronics,female;providesconnectiontohandlersystem
31
Description Typical General characteristics
Line power2
Frequency 47Hzto63HzVoltage 90-264VAC(Vpeak>120V)
VAmax 350VAmax.
PowerConsumptionOption230/235/240/245/260/265/280/285Option430/435/440/445/460/465/480/485Option2D5/2K5Option4D5/4K5
130W(SPD)155W(SPD)160W(SPD)185W(SPD)
Description Specification General characteristicsAUX input connectorType BNC,femalex2Inputrange ±1Vor±10VselectableAccuracy 1%+1mVfor±1Vinput
1%+10mVfor±10Vinput
Table 33. LXIcompliance
Description General characteristics
ClassC(onlyappliestounitsthatareshippedwithfirmwarerevisionA.08.00orlater)
Table 32. Rearpanelinformation (continued)
1. USBTestandMeasurementClass(TMC)interfacethatcommunicatesoverUSB,complyingwith theIEEE488.1andIEEE488.2standards.2. Athird-wiregroundisrequired.
32
Table 34. EMC,safetyandenvironment
Description General characteristicsEMC
EuropeanCouncilDirective2004/108/EC IEC61326-1:2005 EN61326-1:2006CISPR11:2003+A1:2004 EN55011:2007 Group1,ClassA IEC61000-4-2:1995+A2:2000 EN61000-4-2:1995+A2:2001 4kVCD/8kVAD IEC61000-4-3:2006 EN61000-4-3:2006 1-3V/m,80-1000MHz/1.4GHz-2.7GHz,80%AM IEC61000-4-4:2004 EN61000-4-4:2004 1kVpowerlines/0.5kVsignallines IEC61000-4-5:2005 EN61000-4-5:2006 0.5kVline-line/1kVline-ground IEC61000-4-6:2003+A1:2004+A2:2006 EN61000-4-6:2007 3V,0.15-80MHz,80%AM IEC61000-4-11:2004 EN61000-4-11:2004 0.5-300cycle,0%/70%
ICES-001:2006Group1,ClassA
AS/NZSCISPR11:2004Group1,ClassA
SafetyEuropeanCouncilDirective2006/95/EC IEC61010-1:2001/EN61010-1:2001 MeasurementCategoryI PollutionDegree2 IndoorUseCAN/CSAC22.2No.61010-1-04 MeasurementCategoryI PollutionDegree2 IndoorUse
EnvironmentThisproductcomplieswiththeWEEEDirective(2002/96/EC)markingrequirements.Theaffixedlabelindicatesthatyoumustnotdiscardthiselectrical/electronicproductindomestichouseholdwaste.ProductCategory:WithreferencetotheequipmenttypesintheWEEEDirectiveAnnexI,thisproductisclassedasa“MonitoringandControlinstrumentation”product.Donotdisposeindomestichouseholdwaste.Toreturnunwantedproducts,contactyourlocalAgilentoffice,orseewww.agilent.com/environment/product/formoreinformation.
33
Table 35.Analyzerenvironmentalspecificationsanddimensions
Description General characteristicsOperating environmentTemperature +5°Cto+40°C
Error-correctedtemperaturerange 23°C(±5°C)with<1°CdeviationfromcalibrationtemperatureHumidity 20%to80%atwetbulbtemperature<+29°C(non-condensation)
Altitude 0to2,000m(0to6561feet)
Vibration 0.21Gmaximum,5Hzto500Hz
Non-Operating storage environmentTemperature –10°Cto+60°C
Humidity 20%to90%atwetbulbtemperature<+40°C(non-condensation)
Altitude 0to4572m(0to15,000feet)Vibration 0.5Gmaximum,5Hzto500HzDimensions Seenextpage.Weight (net)Option230/240/260/280(2-port) Option235/245/265/285(2-port) Option430/480/440/460(4-port) Option435/445/465/485(4-port) Option2D5/2K5(2-port) Option4D5/4K5(4-port)
18.2kg 18.3kg 19.9kg 20.0kg 19.8kg 21.8kg
34
Figure 3. Dimensions (front view, E5071C with Option 230/235/240/245/260/265/280/285, in millimeters)
Figure 4. Dimensions (front view, E5071C with Option 430/435/440/445/460/465/480/485, in millimeters)
426
58 20 51 122 3727
222
221922
426
58 20 51 41 41 41 3727
222
221922
35
426
58 20 51 122 3727
222
261922
Figure 5. Dimensions (front view, E5071C with Option 2D5/2K5, in millimeters)
Figure 6. Dimensions (front view, E5071C with Option 4D5/4K5, in millimeters)
36
Figure 7. Dimensions (rear view with Option 1E5, in millimeters)
Figure 8. Dimensions (side view, E5071C Option 230/235/240/245/260/265/280/285/430/435/440/445/460/465/480/485, in millimeters)
Figure 9. Dimensions (side view, E5071C with Option 2D5/2K5/4D5/4K5, in millimeters)
1821
5
15
235
1322
2
47241732 23.4
482196422426
128
16729225
252525
22
2558
144 159 17
9 190217
64109147
25 25
47232 417 23
14
215
18
222
1323
5
37
Measurement Throughput Summary1, 2
Cycle time for measurement completion (ms)
Table 36. Option240/245/260/265/280/285/440/445/460/465/480/485
Sweep mode: Swept, analyzer display turned off with: DISP:ENAB OFF, number of traces = 1, system error correction: OFF
Number of points51 201 401 1601
Start 1 GHz, stop 1.2 GHz, 500 kHz IF bandwidthUncorrected 4 5 7 172-portcal 6 9 12 334-portcal 12 17 24 66Start 1 GHz, stop 1.2 GHz, 100 kHz IF bandwidthUncorrected 4 5 7 192-portcal 7 9 13 374-portcal 12 18 26 73Start 1 GHz, stop 1.2 GHz, 1 kHz IF bandwidthUncorrected 53 200 395 15622-portcal 106 400 790 31234-portcal 211 799 1579 6245Start 100 kHz, stop 4.5 GHz, 500 kHz IF bandwidthUncorrected 11 13 14 232-portcal 20 25 27 454-portcal 40 49 53 95Start 100 kHz, stop 4.5 GHz, 100 kHz IF bandwidthUncorrected 11 13 14 252-portcal 21 25 27 494-portcal 40 50 54 102Start 100 kHz, stop 4.5 GHz, 1 kHz IF bandwidthUncorrected 56 205 402 15812-portcal 111 409 804 31624-portcal 222 818 1608 6323
1. Supplementalperformancedata. 2. MeasuredwithfirmwareversionA.11.0xwithserialnumberprefixMY463.
38
Start 100 kHz, stop 8.5 GHz, 500 kHz IF bandwidthUncorrected 14 18 19 232-portcal 28 35 37 454-portcal 55 69 74 90Start 100 kHz, stop 8.5 GHz, 100 kHz IF bandwidth
Uncorrected 14 18 19 252-portcal 28 35 37 494-portcal 55 69 74 98Start 100 kHz, stop 8.5 GHz, 1 kHz IF bandwidthUncorrected 56 205 403 15812-portcal 112 410 805 31624-portcal 224 820 1609 6322
Number of points
51 201 401 1601Start 1 GHz, stop 1.2 GHz, 500 kHz IF bandwidthUncorrected 4 8 11 282-portcal 8 14 22 554-portcal 16 28 42 109Start 1 GHz, stop 1.2 GHz, 100 kHz IF bandwidthUncorrected 5 9 14 402-portcal 9 18 28 804-portcal 17 34 55 159Start 1 GHz, stop 1.2 GHz, 1 kHz IF bandwidthUncorrected 53 200 395 15622-portcal 106 400 790 31234-portcal 211 799 1579 6245Start 100 kHz, stop 4.5 GHz, 500 kHz IF bandwidthUncorrected 7 12 18 472-portcal 14 24 36 944-portcal 27 48 71 187
Table 37.Option240/245/260/265/280/285/440/445/460/465/480/485
Sweep mode: Stepped, analyzer display turned off with: DISP:ENAB OFF, number of traces = 1, system error correction: ON
39
Start 100 kHz, stop 4.5 GHz, 100 kHz IF bandwidthUncorrected 8 14 21 602-portcal 14 27 42 1184-portcal 28 54 83 236Start 100 kHz, stop 4.5 GHz, 1 kHz IF bandwidthUncorrected 56 205 403 15812-portcal 111 409 804 31624-portcal 222 818 1608 6323Start 100 kHz, stop 8.5 GHz, 500 kHz IF bandwidthUncorrected 8 13 19 472-portcal 14 25 36 944-portcal 28 49 72 187Start 100 kHz, stop 8.5 GHz, 100 kHz IF bandwidthUncorrected 8 14 22 592-portcal 15 28 43 1184-portcal 30 56 85 236Start 100 kHz, stop 8.5 GHz, 1 kHz IF bandwidthUncorrected 56 205 403 15812-portcal 112 410 805 31624-portcal 224 820 1609 6322
40
Table 38. Option2D5/2K5/4D5/4K5
Sweep mode: Swept, analyzer display turned off with: DISP:ENAB OFF, number of traces = 1, system error correction: OFF
Number of Points51 201 401 1601
Start 11 GHz, stop 12 GHz, 500 kHz IF bandwidthUncorrected 3 3 5 152-portcal 6 6 9 294-portcal 10 11 18 65Start 11 GHz, stop 12 GHz, 100 kHz IF bandwidthUncorrected 3 3 5 172-portcal 6 6 10 334-portcal 11 12 20 71Start 11 GHz, stop 12 GHz, 1 kHz IF bandwidthUncorrected 52 199 395 15652-portcal 103 397 789 31284-portcal 205 794 1577 6256Start 8 GHz, stop 18 GHz, 500 kHz IF bandwidthUncorrected 17 21 22 222-portcal 33 42 43 444-portcal 66 82 85 88Start 8 GHz, stop 18 GHz, 100 kHz IF bandwidthUncorrected 17 21 22 242-portcal 34 42 43 474-portcal 67 83 86 93Start 8 GHz, stop 18 GHz, 1 kHz IF bandwidthUncorrected 57 206 403 15812-portcal 114 411 805 31624-portcal 227 822 1610 6323Start 300 kHz, stop 20 GHz, 500 kHz IF bandwidthUncorrected 22 36 39 432-portcal 44 71 77 844-portcal 88 141 153 168Start 300 kHz, stop 20 GHz, 100 kHz IF bandwidthUncorrected 23 36 39 432-portcal 45 71 78 854-portcal 89 142 154 169Start 300 kHz, stop 20 GHz, 1 kHz IF bandwidthUncorrected 60 210 408 15902-portcal 118 420 816 31794-portcal 236 839 1630 6357
41
Table 39.Option2D5/2K5/4D5/4K5
Sweep mode: Stepped, analyzer display turned off with: DISP:ENAB OFF, number of traces = 1, system error correction: ON
Number of Points51 201 401 1601
Start 11 GHz, stop 12 GHz, 500 kHz IF bandwidthUncorrected 3 6 11 312-portcal 5 12 20 614-portcal 10 24 40 120Start 11 GHz, stop 12 GHz, 100 kHz IF bandwidthUncorrected 3 8 14 432-portcal 6 15 26 854-portcal 11 30 52 170Start 11 GHz, stop 12 GHz, 1 kHz IF bandwidthUncorrected 52 199 395 15652-portcal 103 397 789 31284-portcal 205 794 1577 6256Start 8 GHz, stop 18 GHz, 500 kHz IF bandwidthUncorrected 9 13 19 472-portcal 16 26 37 944-portcal 32 51 73 187Start 8 GHz, stop 18 GHz, 100 kHz IF bandwidthUncorrected 9 15 22 602-portcal 17 29 43 1184-portcal 33 58 86 236Start 8 GHz, stop 18 GHz, 1 kHz IF bandwidthUncorrected 57 206 403 15812-portcal 114 411 805 31624-portcal 227 822 1610 6323Start 300 kHz, stop 20 GHz, 500 kHz IF bandwidthUncorrected 11 18 24 562-portcal 21 35 47 1114-portcal 41 68 94 221Start 300 kHz, stop 20 GHz, 100 kHz IF bandwidthUncorrected 11 19 27 682-portcal 21 38 53 1354-portcal 42 74 106 270Start 300 kHz, stop 20 GHz, 1 kHz IF bandwidthUncorrected 60 210 408 15902-portcal 118 420 816 31794-portcal 236 839 1630 6357
42
Cycle time (ms) vs. number of points
Table 40. Option240/245/260/265/280/285/440/445/460/465/480/485
Start 1 GHz, stop 1.2 GHz, 500 kHz IF bandwidth, error correction: OFF, display update: OFF, number of traces = 1
Number of points Sweep mode: Swept, System error correction: OFF
Sweep mode: Stepped, System error correction: ON
51 4 4201 5 8401 7 111601 17 28
Table 41. Option2D5/2K5/4D5/4K5
Start 11 GHz, stop 12 GHz, 500 kHz IF bandwidth, error correction: OFF, display update: OFF, number of traces = 1
Number of points Sweep mode: Swept, System error correction: OFF
Sweep mode: Stepped, System error correction: ON
51 3 3201 3 6401 5 111601 15 31
43
Cycle time (ms) vs. IF bandwidth
Table 42.240/245/260/265/280/285/440/445/460/465/480/485
Sweep mode: Swept, analyzer display turned off with: DISP: ENAB OFF, number of traces = 1, system error correction: OFF, Frequency = 4 GHz, NOP = 201
IF BW [Hz]
Cycle time [ms]
IF BW [Hz]
Cycle time [ms]
IF BW [Hz]
Cycle time [ms]
IF BW [kHz]
Cycle time [ms]
IF BW [kHz]
Cycle time [ms]
IF BW [kHz]
Cycle time [ms]
10 19300 100 1933 1000 196 10 22 100 5 1000 515 12868 150 1290 1500 132 15 16 150 5 1500 520 9652 200 968 2000 100 20 13 200 530 6436 300 647 3000 68 30 9 300 540 4827 400 486 4000 52 40 8 400 550 3863 500 389 5000 42 50 7 500 570 2737 700 277 7000 30 70 6 700 5
Table 43.Option2D5/2K5/4D5/4K5
Sweep mode: Swept, analyzer display turned off with: DISP: ENAB OFF, number of traces = 1, system error correction: OFF, Frequency = 10 GHz, NOP = 201
IF BW [Hz]
Cycle time [ms]
IF BW [Hz]
Cycle time [ms]
IF BW [Hz]
Cycle time [ms]
IF BW [kHz]
Cycle time [ms]
IF BW [kHz]
Cycle time [ms]
IF BW [kHz]
Cycle time [ms]
10 19328 100 1931 1000 194 10 20 100 3 1000 315 12890 150 1288 1500 130 15 14 150 3 1500 320 9670 200 966 2000 98 20 11 200 330 6448 300 645 3000 66 30 7 300 340 4836 400 484 4000 50 40 6 400 350 3868 500 387 5000 40 50 5 500 370 2737 700 275 7000 28 70 4 700 3
44
Cycle time (ms) vs. RF Range Fixed Mode
Table 44. Option230/235/240/245/260/265/280/285/430/435/440/445/460/465/480/485
Sweep mode: Swept, analyzer display turned off with: DISP:ENAB OFF,number of traces = 1, system error correction: OFF, Start 1 GHz, stop 1.2 GHz, 500 kHz IF bandwidth
Number of points51 201 401 1601
RF Range Fixed Mode: ON Uncorrected 2 3 5 152-portcal 2 5 8 294-portcal 4 9 16 58RF Range Fixed Mode: OFFUncorrected 4 5 7 172-portcal 6 9 12 334-portcal 12 17 24 66
Sweep mode: Swept, analyzer display turned off with: DISP:ENAB OFF, number of traces = 1, system error correction: OFF, Start 1 GHz, stop 1.2 GHz, 100 kHz IF bandwidth
Number of points51 201 401 1601
RF Range Fixed Mode: ONUncorrected 2 3 5 172-portcal 3 5 9 334-portcal 4 10 18 65RF Range Fixed Mode: OFFUncorrected 4 5 7 192-portcal 7 9 13 374-portcal 12 18 26 73
45
Data transfer time (ms)1, 2
Table 45. Alloptions
Number of points51 201 401 1601
SCPI over GPIB3
64-bitfloatingpoint 4 12 22 8432-bitfloatingpoint 3 6 12 43ASCII 25 98 196 773SCPI over 1 Gbps LAN (Socket)3
REAL64 1 1 1 2REAL32 1 1 1 2ASCII 15 55 108 432SCPI over 1 Gbps LAN (SICL-LAN)3
REAL64 3 3 3 5REAL32 3 3 3 4ASCII 3 5 9 28SCPI over USB (SICL-USB)3
REAL64 2 2 2 3REAL32 2 2 2 3ASCII 2 6 12 43SCPI over GPIB/USB (82357B)REAL64 8 15 24 81REAL32 6 10 15 43ASCII 74 282 561 2240COM4
Varianttype 1 1 1 1
1. Supplementalperformancedata.2. MeasuredwithfirmwareversionA.11.00withserialnumberprefixMY463. 3. MeasuredusingaVEEPro7.0programrunningona3.2GHzPentium4DELLPrecision370, TransferredcomplexS11data,using:CALC1-36:DATA:FDAT?.4. MeasuredusinganE5071CVBAmacrorunninginsidetheanalyzer.TransferredcomplexS11data.
46
E5092A Configurable multiport test setThesectionprovidestestinput/outputperformancewithoutcalibrationbytheE5071C.
Table 46.Testsetinput/outputperformance
Description Specification TypicalFrequencyrange 50MHzto20GHz
Damagelevel 20dBm,±35VDC
Table 47. OptionE5092A-020portperformance
Description Specification TypicalLoad match (selected port)
SPDT switch1 50MHzto2GHz 2GHzto4GHz 4GHzto8GHz 8GHzto10GHz 10GHzto18GHz 18GHzto20GHz
17dB 11dB 8dB 7dB 4dB 4dB
SP4T switch2 50MHzto2GHz 2GHzto3GHz 3GHzto8GHz 8GHzto10GHz 10GHzto18GHz 18GHzto20GHz
17dB 11dB 8dB 7dB 4dB 4dB
Load match (unselected port)
SPDT switch1 50MHzto3GHz 3GHzto10GHz 10GHzto16GHz 16GHzto18GHz 18GHzto20GHz
17dB 11dB 8dB 6dB 4dB
SP4T switch2 50MHzto3GHz 3GHzto10GHz 10GHzto16GHz 16GHzto18GHz 18GHzto20GHz
17dB 11dB 8dB 6dB 4dB
1. SPDT:Single-pole-double-throwswitches.AppliestoSW5,SW6,SW7,SW8,SW9andSW10intheE5092A.(SeeFigure20.) 2. SP4T:Single-pole-four-throwswitches.AppliestoSW1,SW2,SW3andSW4intheE5092A.(SeeFigure20.)
47
Description Specification TypicalLoad match (common port)SPDT switch1 50MHzto2GHz 2GHzto4GHz 4GHzto8GHz 8GHzto10GHz 10GHzto20GHz
16dB 11dB 8dB 7dB 4dB
SP4T switch2 50MHzto1.3GHz 1.3GHzto4GHz 4GHzto8GHz 8GHzto10GHz 10GHzto20GHz
16dB 11dB 8dB 7dB 4dB
Insertion lossSPDT switch1 50MHzto100MHz 100MHzto2GHz 2GHzto3GHz 3GHzto4GHz 4GHzto6GHz 6GHzto8GHz 8GHzto10GHz 10GHzto14GHz 14GHzto18GHz 18GHzto20GHz
4dB 3.5dB 4.5dB 5dB 5.5dB 7dB 8dB 8.5dB 10dB 11.5dB
SP4T switch2 50to100MHz 100MHzto2GHz 2GHzto3GHz 3GHzto4GHz 4GHzto6GHz 6GHzto8GHz 8GHzto10GHz 10GHzto14GHz 14GHzto18GHz 18GHzto20GHz
4dB 3.5dB 4.5dB 5.5dB 6dB 7.5dB 8.5dB 9.5dB 10.5dB 12dB
Stability per switch Condition:EnviromentTemperature+23°C±3°CandInternalDCsource:≤100mA (Sumof4channels),noheatsourceandnowallclosetotheunit.50Mto4GHz4Gto12GHz12Gto20GHzCondition:besidestheabove50Mto4GHz4Gto12GHz12Gto20GHz
0.003dB/°C(SPD)0.005dB/°C(SPD)0.008dB/°C(SPD)
0.007dB/°C(SPD)0.012dB/°C(SPD)0.017dB/°C(SPD)
Isolation3 50MHzto500MHz 500MHzto1GHz 1GHzto2GHz 2GHzto6GHz 6GHzto10GHz 10GHzto18GHz 18GHzto20GHz
65dB 80dB 85dB 90dB 85dB 75dB 65dB(Overarbitrarilytestports)
Table 48.OptionE5092A-020portperformance(continued)
1. SPDT:Single-pole-double-throwswitches.AppliestoSW5,SW6,SW7,SW8,SW9andSW10intheE5092A.(SeeFigure20.) 2. SP4T:Single-pole-four-throwswitches.AppliestoSW1,SW2,SW3andSW4intheE5092A.(SeeFigure20.) 3. Thisspecificationisdefinedwhenallportsareterminatedwitha50ohmload.
48
Table 49. Controlline
Description Specification TypicalNumberofgroups 4
GroupA:8bitsGroupB,C,D:4bits
Inputvoltagerange1 0Vto+5V(positiveinput)–5Vto0V(negativeinput)
Maximumcurrent GroupA,B:50mAintotalofeachgroupGroupC,D:500uAintotalofeachgroup
Impedance GroupA,B:<10ohmGroupC,D:<200ohm
Table 50.DCsource
Description Specification Typical
Numberofsources 4
Outputvoltagerange 0Vto+5.2V(nominal)2
Outputvoltageaccuracy ±3%ofsetting(+1Vto+5V)at 1Mohmloadimpedance
Voltageresolution 10mV(nominal)3
Maximumcurrent 150mAforeachsource
Outputimpedance <5ohm
Table 51. Operatingstorageenvironment
Description General characteristics
Temperature +5°Cto+40°C
Humidity 20to80%atwetbulbtemperature<+29°C(non-condensing)
Altitude 0to2,000m(0to6,561feet)
Vibration 0.21Gmax.,5to500Hz
Table 52. Non-operatingstorageenvironment
Description General characteristics
Temperature –10°Cto+60°C
Humidity 20to90%atwetbulbtemperature<+40°C(non-condensing)
Altitude 0to4,572m(0to15,000feet)
Vibration 0.5Gmax.,5Hzto500Hz
1. Inputvoltagewillbeclippedatabout±5.2Vwhenoverthisrange. 2. Theoutputvoltagecanbesetinthisrange. 3. Theoutputvoltageresolutionbecomeseffectivebetween0Vto5.2V.
49
Table 53.Frontpanelinformation
Description General characteristicsRFconnectors SMA(Female)Testports 38portsControlline 15-pinD-sub,female
25-pinD-sub,female
Table 54.Rearpanelinformation
Description General characteristicsUSBport TypeB-receptacle,provide
connectiontotheE5071CLinepower1FrequencyVoltage
VAmax
47to63Hz90to132VAC,or198to264VAC(automaticallyswitched)300VAmax.
Table 55.Testsetdimensionsandblockdiagram
Description General characteristics Dimensions E5092AOption020 SeeFigures16,17,18and19 Weight E5092AOption020 9kg
Figure 10. Dimensions (front view, with Option E5092A-020, in millimeters, nominal)
426
129192
133
18
1. 1Athird-wiregroundisrequired.
50
Figure 11. Dimensions (pitch between switches, with Option E5092A-020, in millimeters, nominal)
Figure 12. Dimensions (rear view, with Option E5092A-020, in millimeters, nominal)
Figure 13. Dimensions (side view, with Option E5092A-020, in millimeters, nominal)
129 37
133
51
83
36.8
132.7
2
18.57
17
27
27
65.34
23.38
23.38
40.640.640.6
13.5 27 69.8
27
27
2727 27.8
146
1313
3
1812
614
4
47223 417 32 22
51
Figure 14. Switch configuration (E5092A-020)
Figure 15. DC control line (E5092A-020)
Control Line 1 (Group A)
Control Line 2 (Group A)
Control Line 3 (Group A)
Control Line 4 (Group A)
Control Line 8 (Group A):
Control Line 2 (Group B)Control Line 3 (Group B)Control Line 4 (Group B)
Control Line 1 (Group B)
Control Line 1 (Group C)Control Line 2 (Group C)Control Line 3 (Group C)Control Line 4 (Group C)
Control Line 1 (Group D)Control Line 2 (Group D)Control Line 3 (Group D)Control Line 4 (Group D)
::
DC Source (Group A)Control Line 1 (Group A)
DC Source (Group B)
DC Source (Group C)
DC Source (Group D)
Control Line 2 (Group B)
Control Line 2 (Group C)
Control Line 2 (Group D)Positive Input (High)
Negative Input (Low)
Positive Input (High)
Negative Input (Low)
Positive Input (High)
Negative Input (Low)
DC Source Output
DC Source Output
DC Source Output
DC Source Output
ImpedanceNegative Input (Low)
Max Current Positive Input (High)
Output Impedance
Output Voltage
SW 6 6A 6B
6C O M
SW 7
7C O M
7A 7B SW 8 8A 8B
8C O M
SW 9
9C O M
9A 9B SW 1010A 10B
10C O M
SW 5 5A
5C O M
5B
SW 1
1A 1B 1C 1D
PO R T 1 SW 2
2A 2B 2C 2D
PO R T 2 SW 3
3A 3B 3C 3D
PO R T 3 SW 4
4A 4B 4C 4D
PO R T 4
52
D-SUB 25pin assignment
Line
4
Line
3
Line
2
Line
1
Line
4
Line
3
Line
2
Line
1
Posit
ive in
put
Posit
ive in
put
Nega
tive
inpu
t
GND
DC so
urce
GND
DC so
urce
23 22 21 20 19 18 1712
GND
Nega
tive
inpu
t
24
GND
2513 11 10 9 8 7 6 5
Line
4Ne
gativ
e in
put
164
Line
3Po
sitive
inpu
t
153
Line
2DC
sour
ce
142
Line
1
1
GROUP B GROUP C GROUP D
GROUP B GROUP C GROUP D
Line
8
Line
7
Line
6
Line
5
Line
4
Line
3
Line
2
Line1
GND
Rese
rved
DC so
urce
Posit
ive in
put
Nega
tive
inpu
t
Rese
rved
Rese
rved
15 14 13 12 11 10 98 7 6 5 4 3 2 1
GROUP A
GROUP A
D-SUB 15 pin assignment
Figure 16. Control line pin assignment (E5092A-020)
53
Option 230/235/240/245/260/265/280/285/430/435/440/445/ 460/465/480/485
Table 56. Correctedsystemperformancewithtype-N75Ωdeviceconnectors, 85036Ecalibrationkit
Network analyzer: E5071C calibration kit: 85036E (type-N 75 Ω) 50 to 75 Ω adapters: 11852B calibration: full 2-port
IF bandwidth = 10 Hz, no averaging applied to data, environmental temperature = 23 °C ±5 °C with < 1 °C deviation from calibration temperature, isolation calibration performed
Typical (dB)Description 10 MHz to 3 GHzDirectivity 37Sourcematch 33Loadmatch 39Reflectiontracking ±0.015Transmissiontracking ±0.019
10 MHz to 3 GHz
S11 = S22 = 0; Source power = –10 dBm
Transmission using 85036E and 11852B
Transmission coefficient (dB)
10
1
0.1
0.01
Mag
(dB)
10 0 –10 –20 –30 –40 –50 –60 –70 –80 –90
10 MHz to 3 GHz
S11 = S22 = 0; Source power = –10 dBm
Transmission using 85036E and 11852B
Transmission coefficient (dB)
100
10
1
0.1
Phas
e (d
eg)
10 0 –10 –20 –30 –40 –50 –60 –70 –80 –90
10 MHz to 3 GHz
S21 = S12 = 0; Source power = –10 dBm
Reflection using 85036E and 11852B
Reflection coefficient (linear)
10
8
6
4
2
0
Phas
e (d
eg)
0 0.2 0.4 0.6 0.8 1
10 MHz to 3 GHz
S21 = S12 = 0; Source power = –10 dBm
Reflection using 85036E and 11852B
Reflection coefficient (linear)
0.1
0.08
0.06
0.04
0.02
0
Mag
(lin
ear)
0 0.2 0.4 0.6 0.8 1
Transmissionuncertainty10MHzto3GHz(typical)
Reflectionuncertainty10MHzto3GHz(typical)
Magnitude Phase
Magnitude Phase
Corrected System Performance for 75 Ω Measurements with 11852B50 to 75 Ω Minimum-Loss Pads (Supplemental Information)
www.agilent.comwww.agilent.com/find/ena
www.lxistandard.orgLANeXtensionsforInstrumentsputsthepowerofEthernetandtheWebinsideyourtestsystems.AgilentisafoundingmemberoftheLXIconsortium.
Agilent Channel Partnerswww.agilent.com/find/channelpartnersGetthebestofbothworlds:Agilent’smeasurementexpertiseandproductbreadth,combinedwithchannel partnerconvenience.
www.agilent.com/find/myagilentApersonalizedviewintotheinformationmostrelevanttoyou.
myAgilentmyAgilent
www.agilent.com/quality
www.agilent.com/find/AdvantageServicesAccuratemeasurementsthroughoutthelifeofyourinstruments.
Agilent Advantage Services
Three-Year Warranty
www.agilent.com/find/ThreeYearWarrantyAgilent’scombinationofproductreliabilityandthree-yearwarrantycoverageisanotherwaywehelpyouachieveyourbusinessgoals:increasedconfidenceinuptime,reducedcostofownershipandgreaterconvenience.
FormoreinformationonAgilentTechnologies’products,applicationsorservices,pleasecontactyourlocalAgilentoffice.Thecompletelistisavailableat:www.agilent.com/find/contactus
Americas Canada (877)8944414Brazil (11)41973600Mexico 018005064800 UnitedStates (800)8294444
Asia Pacific Australia 1800629485China 8008100189HongKong 800938693India 1800112929Japan 0120(421)345Korea 0807690800Malaysia 1800888848Singapore 18003758100Taiwan 0800047866OtherAPCountries (65)3758100
Europe & Middle EastBelgium 32(0)24049340Denmark 4545801215Finland 358(0)108552100France 0825010700* *0.125€/minuteGermany 49(0)70314646333 Ireland 1890924204Israel 972-3-9288-504/544Italy 390292608484Netherlands 31(0)205472111Spain 34(91)6313300Sweden 0200-882255UnitedKingdom 44(0)1189276201Forotherunlistedcountries: www.agilent.com/find/contactus(BP-3-1-13)
Productspecificationsanddescriptionsinthisdocumentsubjecttochangewithoutnotice.
©AgilentTechnologies,Inc.2013PublishedinUSA,April5,20135989-5479EN