GE.10- Agreement Concerning the Adoption of Uniform Technical Prescriptions for Wheeled Vehicles, Equipment and Parts which can be Fitted and/or be Used on Wheeled Vehicles and the Conditions for Reciprocal Recognition of Approvals Granted on the Basis of these Prescriptions* (Revision 2, including the amendments which entered into force on 16 October 1995) Addendum 47: Regulation No. 48 Revision 6 – Amendment 1 Supplement 4 to the 04 series of amendments to the Regulation: Date of entry into force: 19 August 2010 Uniform provisions concerning the approval of vehicles with regard to the installation of lighting and light-signalling devices UNITED NATIONS * Former title of the Agreement: Agreement Concerning the Adoption of Uniform Conditions of Approval and Reciprocal Recognition of Approval for Motor Vehicle Equipment and Parts, don’t at Geneva on 20 March 1958. E/ECE/324/Rev.1/Add.47/Rev.6/Amend.1-E/ECE/TRANS/505/Rev.1/Add.47/Rev.6/Amend.1 4 October 2010
Transcript
GE.10-
Agreement
Concerning the Adoption of Uniform Technical Prescriptions for Wheeled Vehicles, Equipment and Parts which can be Fitted and/or be Used on Wheeled Vehicles and the Conditions for Reciprocal Recognition of Approvals Granted on the Basis of these Prescriptions*
(Revision 2, including the amendments which entered into force on 16 October 1995)
Addendum 47: Regulation No. 48
Revision 6 – Amendment 1
Supplement 4 to the 04 series of amendments to the Regulation: Date of entry into force: 19 August 2010
Uniform provisions concerning the approval of vehicles with regard to the installation of lighting and light-signalling devices
UNITED NATIONS
* Former title of the Agreement: Agreement Concerning the Adoption of Uniform Conditions of Approval and Reciprocal Recognition of Approval for Motor Vehicle Equipment and Parts, don’t at Geneva on 20 March 1958.
Paragraph 2.7.6., insert a reference to footnote 3 and a new footnote 3 to read:
“2.7.6. … a common lamp body3;
__________________ 3 Examples to enable a decision regarding reciprocal incorporation of lamps can be found in
Annex 3, Part 7.”
Paragraph 2.8., amend to read:
“2.8. “Light emitting surface” of … see Annex 3 (See e.g. Parts 1, and 4);
…
b) … see Annex 3. (See e.g. Part 5);”
Insert a new paragraph 2.8.1., to read:
“2.8.1. “Textured outer lens” or “Textured outer lens area” means all or part of an outer lens, designed to modify or influence the propagation of light from the light source(s), such that the light rays are significantly diverted from their original direction.”
Paragraph 2.9.1., amend to read:
“2.9.1. "Illuminating surface of a lighting” … are adjustable relative to one another, the mean adjustment should be used.
In the case of AFS being installed: where a lighting function is produced by two or more simultaneously operated lighting units on a given side of the vehicle, the individual illuminating surfaces, taken together, constitute the illuminating surface to be considered (for example, in the figure of paragraph 6.22.4. below, the individual illuminating surfaces of the lighting units 8, 9 and 11, regarded together and taking into account their respective location, constitute the illuminating surface to be considered for the right hand side of the vehicle).”
Paragraph 2.9.2., amend to read:
“2.9.2. “Illuminating surface of a light-signalling device … encloses a non-lighted surface, the illuminating surface may be considered to be the light emitting surface itself. (See e.g. Annex 3, Parts 2, 3, 5 and 6)”
Paragraph 2.10., amend to read:
“2. 10. The “apparent surface” for a defined direction of observation means, at the request of the manufacturer or his duly accredited representative, the orthogonal projection of:
either the boundary of the illuminating surface projected on the exterior surface of the lens;
or the light-emitting surface;
in a plane perpendicular to the direction of observation and tangential to the most exterior point of the lens. Different examples of the application of apparent surface can be found in Annex 3 to this Regulation.”
Paragraphs 2.29.1. to 2.29.4. and 2.30. to 2.32.1., the reference to footnote 3 and footnote 3, renumber as footnote 4.
Paragraph 4.4.1., the reference to footnote 4 and footnote 4, renumber as footnote 5.
Optional Category 6 side direction indicator lamp shall be fitted in the area between the first and last quartiles of the length of a trailer.
6.5.5. Geometric visibility
6.5.5.1. Horizontal angles: (see figure below)
… The vertical angle above the horizontal may be reduced to 5° if the optional rear lamps are not less than 2,100 mm above the ground.
…”
Paragraph 6.5.8., amend to read (the reference to footnote 12 and footnote 12, renumber as footnote 13):
“6.5.8. Tell-tale
…
For the optional direction-indicator lamps on motor vehicles and trailers, operating tell-tale shall not be mandatory.”
Paragraph 6.14.4.2., amend to read:
“6.14.4.2. In height: Above the ground, not less than 250 mm nor more than 900 mm (not more than 1,200 mm if grouped with any rear lamp(s), 1,500 mm if the shape of the bodywork makes it impossible to keep within 900 mm or 1200 mm respectively).”
Paragraph 6.15.4.2., amend to read:
“6.15.4.2. In height: Above the ground, not less than 250 mm nor more than 900 mm (not more than 1,200 mm if grouped with any rear lamp(s),1,500 mm if the shape of the bodywork makes it impossible to keep within 900 mm or 1200 mm respectively).”
Paragraph 6.17.4.2., amend to read:
“6.17.4.2. In height: Above the ground, not less than 250 mm nor more than 900 mm (not more than 1,200 mm if grouped with any lamp(s), 1,500 mm if the shape of the bodywork makes it impossible to keep within 900 mm or 1200 mm respectively or if the presence of the device is not mandatory according to paragraph 6.17.1.).”
Paragraph 6.17.4.3., amend to read:
“6.17.4.3. …
However, for motor vehicles the length of which does not exceed 6 m, it is sufficient to have one side retro-reflector fitted within the first third and/or one within the last third of the vehicle length. For M1 vehicles the length of which exceeds 6 m but does not exceed 7 m it is sufficient to have one side retro-reflector fitted not further than 3 m from the front and one within the last third of the vehicle length.”
However, for vehicles the length of which does not exceed 6 m and for chassis-cabs it is sufficient to have one side-marker lamp fitted within the first third and/or within the last third of the vehicle length. For M1 vehicles the length of which exceeds 6 m but does not exceed 7 m it is sufficient to have one side-marker lamp fitted not further than 3 m from the front and one within the last third of the vehicle length.”
Paragraph 6.19., the reference to footnote 13 and footnote 13, renumber as footnote 14.
Paragraph 6.19.7.1., the reference to footnote 14 and footnote 14, renumber as footnote 15.
Paragraph 6.20.4.1., amend to read:
“6.20.4.1. In width: one cornering lamp shall be located on each side of the vehicle's median longitudinal plane.”
Paragraphs 6.21.4.1.3. and 6.21.4.2.3., the reference to footnote 15 and footnote 15, renumber as footnote 16.
Paragraph 6.21.7.1., amend to read:
“6.21.7.1. Conspicuity markings shall be considered continuous if the distance between adjacent elements are as small as possible and do not exceed 50 per cent of the shortest adjacent element length. However, if the manufacturer can prove to the satisfaction of the authority responsible for type approval that it is impossible to respect the value of 50 per cent, the distance between adjacent elements may be larger than 50 per cent of the shortest adjacent element, and it shall be as small as possible and not exceed 1000 mm.”
Paragraph 6.22.4.1.2., the reference to footnote 16 and footnote 16, renumber as footnote 17.
Paragraph 6.22.7.4.3., the reference to footnote 17 and footnote 17, renumber as footnote 18.
Paragraph 6.22.7.4.5., the reference to footnote 18 and footnote 18, renumber as footnote 19.
Paragraph 6.22.9.1., the reference to footnote 19 and footnote 19, renumber as footnote 20.
Part 5 – Example of illuminating surface incomparison with light-emitting surface in the case of a “single function lamp” (See paragraphs 2.8. to 2.9 of this Regulation)
Examples of a light source with a reflector optic behind an outer lens:
Example 1: Example 2
(Including the outer lens) (Excluding the non textured outer lens)
Examples of a light source with a reflector optic with a inner lens behind an outer lens:
Example 3: Example 4
(Including the outer lens) (Excluding the non textured outer lens)
Examples of a light source with a reflector optic with a partial inner lens behind an outer lens:
Example 5: Example 6
(Including the outer lens) (Excluding the non textured outer lens)
Example of a light guide optic behind an outer lens:
Example 7:
Example of a light guide optic or a reflector optic behind an outer lens:
Example 8:
Section
In the case where the non textured outer lens is excluded, “7b” is the apparent surface according to paragraph 2.8. b, and F1 shall not transparent to F2
In the case where the non textured outer lens is excluded, “7b” is the apparent surface according to paragraph 2.8. b.
Example of a light source with a reflector optic in combination with an area which is not part of this function, behind an outer lens:
Example 9:
Part 6 – Examples showing the determination of the light-emitting surface in comparison with illuminating surface (See paragraphs 2.8. and 2.9. of this Regulation)
Note: Reflected light could / may contribute to the determination of the light emitting surface
Example A:
Illuminating surface Declared Light-emitting surface according to 2.8.a
Edges are a and b c and d
In the case where the non textured outer lens is excluded, “7b” is the apparent surface according to paragraph 2.8. b.
Example to determine a light emitting surface according to 2.8.a in combination with an area which is not part of the function:
Declared Light-emitting surface according to 2.8.a
Edges are c-d and e-f
Example E:
Example to determine the apparent surface in combination with an area which is not part of the function and a non textured outer lens (according to 2.8.b):
Declared Light emitting surface according to 2.8b. for example
In the case where the non-textured outer lens is excluded, “7b” is the apparent surface according to paragraph 2.8 and F1 shall not be transparent to F2:
