AGRIMAR (UK) PLC

AGRIMAR (UK) PLC

AGRIMAR (UK) PLC

CANAL COURT, 152 HIGH STREETBRENTFORD, MIDDLESEX TW8 8JAUNITED KINGDOMTEL: 00 44 (0)20 8560 1160FAX: 00 44 (0)20 8560 4466E-MAIL: info@agrimarukplc.co.ukWEB SITE: www.agrimarukplc.co.uk

TRACE ELEMENT RANGE

PRODUCT RANGE

PRODUCT SPECIFICATION USES

AGRI-FER Iron Chelate For soil applicationFe EDDHA 6%

DETA-FER Iron Chelate For foliar applicationFe EDTA 13.2%

MANGANESE Manganese Chelate For soil and foliar application

Mn EDTA 13%

ZINC Zinc Chelate For soil and foliar application

Zn EDTA 14%

COPPER Copper Chelate For soil and foliar application

Cu EDTA 14%

AGRI-MIX No. 1 High Iron Micronutrient For foliar applicationMix for general deficiencies

AGRI-MIX No. 2 Micronutrient Mix for For foliar applicationgeneral deficiencies

NITRO-BOOST High Nitrogen Mix for For foliar applicationactively growing plants

AGRI-FOL 12-6-6 NPK and Micro- For foliar feedingnutrients, all purpose feed

AGRIMAR (UK) PLC

AGRI-FER 6%

Iron Chelate (Fe EDDHA) in micro-granular form. Contains 6% Fe.

For the correction of iron deficiency in crops and ornamentals growing in alkaline and calcareous soils. Recommended for soil application.

DIRECTIONS FOR USE

Dissolve in a convenient amount of water, then apply as a coarse low pressure spray or sprinkle on as a dry powder, either by itself or mixed with an extender such as dry sand.

Applications should always be incorporated into the top few centimetres of soil as soon as possible after application and certainly within the following 1-2 hours. This can be done by harrowing or hoeing in or by irrigation.

Farm Crops:Apply to the soil before cultivation prior to sowing or planting or between the rows, alternatively apply through overhead or ground level irrigation systems.

Deep-Rooting Trees & Shrubs:Apply to the soil in a wide circular bank under the limit of the full branch spread. For best results, nutrients should be in the root zone before seasonal growth begins. For deep rooting trees in regions which have moderate to high rainfall, apply in mid to late winter to allow the rains to wash in the chelate.

Alternatively, use a pressure injector to get the solution down to the root feeding zone. Injections should be no more than one metre apart, in a wide band directly under the limit of the full branch spread. This should be done at the beginning of the season, just before re-growth commences.

If there are weeds or grass growing under the trees, increase the recommended application rate by half as much again.

Shallow Rooting Crops:Apply to the soil along the rows, beginning at the first signs of seasonal re-growth. In moderate to high rainfall areas, do not wash in. In arid regions, wash in sparingly. If the soil is densely-compacted, the surface should be broken up by hoeing or harrowing before applying.

AGRIMAR (UK) PLC1

AGRI-FER 6%

RATES OF APPLICATION

The following rates indicate upper and lower limits. Actual amounts used will depend upon the size of the bush or tree and on the degree of deficiency:

Apples, Apricots, Peaches, Pears, Plums:Apply 25-125 g per tree, depending on size.

Citrus:For young trees, apply at 500-750 g per 100m2. For mature trees, apply at 200-500g per tree.

As an annual maintenance programme, apply at 50-150 g per tree.

Grapes:Apply 10-50 g per vine or 750-1500 g per 100 metres of row, in a band or a side dressing.

Cotton, Peas and Beans, Cereals, Vegetables, Peppers, Root Crops, Potatoes, Tomatoes, Melons and Squashes:Apply 2.5-5.5 kg/ha just before sowing or planting or when iron deficiency symptoms begin to appear.

Raspberries, Strawberries, etc:Apply 750-1500 g per 100 metres of row, in a band or a side dressing.

Rhododendrons, Azaleas, Roses, Forsythias and Other Shrubs:Apply 20-50 g per plant.

Chrysanthemums, Geraniums and Similar Annuals and Perennials:Apply 10-60 g per 10m2.

Rates should be judged according to the age of the plant, variety, soil type and other local conditions.

IRRIGATIONWhen used through an irrigation system the appropriate application rate should be selected from the previous selection. This should then be applied via the irrigation system at a rate not greater than 1 kg (dry weight) per 10,000 Litres of water.

PRECAUTIONS1. Keep well sealed and store in original sealed container.2. Wash hands before meals and after work.3. Store away from children, pets, livestock and food stuffs.4. Store dry, away from strong light.5. Do not apply to crops suffering stress such as extreme temperatures, strong winds, etc.

AGRIMAR (UK) PLC2

AGRI-FER 6%

TECHNICAL DATA

IRON CHELATE (Fe EDDHA) IN MICRO-GRANULAR FORM. CONTAINS 6% Fe

Trade Name:AGRI-FER

Active IngredientFe min 6%

Chemical Name of Active Ingredient:Ferric ethylenediamine bis – (2 hydroxyphenyle acetate)

Chelate Agents:EDDHA

Physical Form:Soluble powder, red/brown in colour.

Packing:1 kg laminated bags; 10 x 1 kgs per carton box.20 kg boxes.

Storage:Store in a cool dry place in original closed container.

HEALTH HAZARDS

a) Effect on eyes – product could cause slight discomfort if allowed to come into contact with delicate eye surfaces, but no permanent damage is likely. It is always advisable to wash eyes if contact with chemicals is suspected.

b) Ingestion – the normally toxic metal ions are held in a complex form (chelated) which reduces their toxicity to a very low level. Risk of injury by accidental ingestion is minimal. In the event of accidental ingestion, the product is not accumulated and is readily eliminated from the body.

c) Effect on skin and mucous membranes – no evidence of irritation or sensitisation.

d) Inhalation – solid products can be dusty and a dust mask should be worn when handling them in bulk, since all dusts are to some extent irritant if inhaled.

FIRST AID

If accidentally ingested – rest patient, give copious amounts of water to drink and seek medical advice.

Skin contamination – wash off with copious amounts of water.

AGRIMAR (UK) PLC3

DETA-FERIron Chelate (Fe EDTA) in soluble powder form. Contains 13.2% Fe.

For the correction of iron deficiency in crops. Recommended for soil application.

DIRECTIONS FOR USE

FOLIAR APPLICATION Hydroponics:Preparation of Solution:Stir 1 part powder into 6 parts water, dilute to the required concentration.

Timing – to obtain maximum benefit, foliar applications should be started as early as possible in the season, as soon as there is sufficient leaf area to absorb the spray.

Wetting Agent – when this product is applied as a foliar spray alone (i.e. not mixed with other pesticides) it is recommended that a non-ionic wetting agent such as AGRIWET is added to the spray solution.

RATES OF APPLICATION

The following rates indicate upper and lower limits. Actual amounts will depend upon the size of plant and on the degree of deficiency.

Field Crops:General recommendation:Apply 1-2 kgs/ha in 300-1000 Litres of water/ha. For severe deficiencies repeat after two weeks.

Fruit Crops:Apply 1-2kg/ha in a repeat high volume spray programme, e.g. 4 applications of 0.5 kgs in 1000 Litres water/ha.

DO NOT EXCEED A SOLUTION OF 0-1% (1gram per Litre).

Glasshouse Crops(Foliar Application):Tomato, Cucumber, Squash etc., Cut Flowers, Carnations, Pot Plants, Potted Flowers: Apply at a rate of 50g/1000 Litres water.

Glasshouse Crops(Compost Application):If iron deficiency in plants growing in growbags or soil-less composts, Deta-Fer may be added to the irrigation water or liquid feed at a rate of 100 g per 1000 Litres water.

If iron deficiency develops first check the pH of the nutrient solution and if necessary adjust to pH 6.0. Then add Deta-Fer at the rate of 80g per 1000 Litres of nutrient solution.

If symptoms persist, repeat the treatment 10-14 days later.

A solution of 10 ppm can be made by adding 75g of Deta-Fer to 1000 Litres of nutrient solution.PRECAUTIONS

1. Keep well sealed and store in original sealed container.

2. Wash hands before meals and after work.

3. Store away from children, pets, livestock and food stuffs.

4. Store dry, away from strong light.

5. Do not apply to crops suffering stress, such as extreme temperatures, strong winds, etc.

AGRIMAR (UK) PLC4

AGRIMAR MANGANESE 13%

Manganese Chelate (EDTA) in soluble granule form. Contains 13% Mn.

For the correction of manganese deficiency in all crops.Recommended for soil and foliar application.

DIRECTIONS FOR USE

Preparation of Solution:Stir 1 part granules into 6 parts water, dilute to the required concentration.

FOLIAR APPLICATION

Timing – to obtain maximum benefit, foliar applications should be started as early as possible in the season, as soon as there is sufficient leaf area to absorb the spray.

Wetting Agent – when this product is applied as a foliar spray alone (i.e. not mixed with other pesticides) it is recommended that a non-ionic wetting agent such as AGRIWET is added to the spray solution.

SOIL APPLICATION

Apply as a course low pressure spray direct to the soil.

Application should always be incorporated into the top few centimetres of soil as soon as possible after application and certainly within the following 1-2 hours. This can be done by harrowing or hoeing in, or by irrigation.

Farm Crops:Apply to the soil before the cultivation prior to sowing or planting or between the rows or through overhead or ground level irrigation systems.

Deep-Rooting Trees and Shrubs:Apply to the soil in a wide circular band under the limit of the full branch spread. For best results, nutrients should be in the root zone before seasonal growth begins. For deep rooting trees in regions which have moderate to high rainfall, apply in mid to late winter to allow the rains to wash in the chelate.

Alternatively, use a pressure injector to get the solution down to the root feeding zone. Injections should be no more than one metre apart, in a wide band directly under the limit of the full branch spread. This should be done at the beginning of the season just before re-growth commences.

If there are weeds or grass growing under the trees, increase the recommended application rate by half as much again.

Shallow-Rooting Crops:Apply to the soil along the rows, beginning at the first signs of seasonal re-growth. In moderate to high rainfall areas, do not wash in. In arid regions, wash in sparingly. If the soil is densely-compacted, the surface should be broken up by hoeing or harrowing before applying.

AGRIMAR (UK) PLC5

AGRIMAR MANGANESE 13%

RATES OF APPLICATION

The following rates indicate upper and lower limits. Actual amounts used will depend upon the type of plant and on the degree of deficiency:

FOLIAR APPLICATION

Field Crops and Greenhouses, General Recommendation:Apply 1-2 kgs/ha in 200-400 Litres water/ha. For severe deficiencies repeat after two weeks.

Fruit Crops:Apply the above quantities in a repeat high volume spray programme.

DO NOT EXCEED A SOLUTION OF 0-1% (1 gram per Litre) WHEN APPLYING AS A FOLIAR SPRAY TO FRUIT CROPS.

SOIL APPLICATION

All Crops:3-4 kgs/ha in 200-400 Litres of water/ha.

Rates should be judged according to the age of the plant, variety, soil type and other local conditions.

IRRIGATIONWhen used through an irrigation system the appropriate application rate should be selected from the previous selection. This should then be applied via the irrigation system at a rate not greater than 1 kg (dry weight) per 10,000 Litres of water.

PRECAUTIONS1. Keep well sealed and store in original sealed container.2. Wash hands before meals and after work.3. Store away from children, pets, livestock and food stuffs.4. Store dry, away from strong light.5. Do not apply to crops suffering stress such as extreme temperatures, strong winds, etc.

AGRIMAR (UK) PLC6

AGRIMAR MANGANESE 13%

TECHNICAL DATA

MANGANESE CHELATE (EDTA) IN SOLUBLE GRANULE FORM. CONTAINS 13% Mn.

Trade Name:AGRIMAR MANGANESE 13%

Active IngredientMn EDTA 13%

Chemical Name of Active Ingredient:Disodium Manganous ethylenediamine tetra acetate

Molecular Weight:389

Physical Form:Soluble granules, white in colour.

Solubility in Water:300g/l (at 20ºC)

Density:0.70-0.85

Moisture:Not greater than 5%

Packing:1 kg laminated bags; 10 x 1 kgs per carton box.25 kgs carton boxes.

Storage:Store in a cool dry place in original closed container.

HEALTH HAZARDS

a) Effect on eyes – product could cause slight discomfort if allowed to come into contact with delicate eye surfaces, but no permanent damage is likely. It is always advisable to wash eyes if contact with chemicals is suspected.

b) Ingestion – the normally toxic metal ions are held in a complex form (chelated) which reduces their toxicity to a very low level. Risk of injury by accidental ingestion is minimal. In the event of accidental ingestion, the product is not accumulated and is readily eliminated from the body.

c) Effect on skin and mucous membranes – no evidence of irritation or sensitisation.

d) Inhalation – solid products can be dusty and a dust mask should be worn when handling them in bulk, since all dusts are to some extent irritant if inhaled.

FIRST AID

If accidentally ingested – rest patient, give copious amounts of water to drink and seek medical advice.

Skin contamination – wash off with copious amounts of water.

AGRIMAR (UK) PLC7

AGRIMAR ZINC 14%

Zinc Chelate (EDTA) in soluble granule form. Contains 14% Zn.

For the correction of zinc deficiency in all crops.Recommended for soil and foliar application.

DIRECTIONS FOR USE

Preparation of Solution:Stir 1 part granules into 6 parts water, dilute to the required concentration.

FOLIAR APPLICATION

Timing – to obtain maximum benefit, foliar applications should be started as early as possible in the season, as soon as there is sufficient leaf area to absorb the spray.

Wetting Agent – when this product is applied as a foliar spray alone (i.e. not mixed with other pesticides) it is recommended that a non-ionic wetting agent such as AGRIWET is added to the spray solution.

SOIL APPLICATION

Apply as a course low pressure spray direct to the soil.

Application should always be incorporated into the top few centimetres of soil as soon as possible after application and certainly within the following 1-2 hours. This can be done by harrowing or hoeing in or by irrigation.

Farm Crops:Apply to the soil before the cultivation prior to sowing or planting, or between the rows or through overhead or ground level irrigation systems.

Deep-Rooting Trees and Shrubs:Apply to the soil in a wide circular band under the limit of the full branch spread. For best results, nutrients should be in the root zone before seasonal growth begins. For deep rooting trees in regions which have moderate to high rainfall, apply in mid to late winter to allow the rains to wash in the chelate.

Alternatively, use a pressure injector to get the solution down to the root feeding zone. Injections should be no more than one metre apart, in a wide band directly under the limit of the full branch spread. This should be done at the beginning of the season just before re-growth commences.

If there are weeds or grass growing under the trees, increase the recommended application rate by half as much again.

Shallow-Rooting Crops:Apply to the soil along the rows, beginning at the first signs of seasonal re-growth. In moderate to high rainfall areas, do not wash in. In arid regions, wash in sparingly. If the soil is densely-compacted, the surface should be broken up by hoeing or harrowing before applying.

AGRIMAR (UK) PLC8

AGRIMAR ZINC 14%

RATES OF APPLICATION

The following rates indicate upper and lower limits. Actual amounts used will depend upon the type of plant and on the degree of deficiency:

FOLIAR APPLICATIONField Crops and Greenhouses, General Recommendation:Apply 1-2 kgs/ha in 200-400 Litres water/ha. For severe deficiencies repeat after two weeks.

Vegetables and Nurseries:Apply 0.5-2 kgs/ha in 200-400 Litres water/ha.

Citrus, Apples, Pears, Stone Fruits:Apply 1-2 kgs/ha in a repeat high volume spray programme, e.g. 4 applications of 0.5 kgs in 500 Litres water/ha.

DO NOT EXCEED A SOLUTION OF 0-1% (1 gram per Litre).

SOIL APPLICATION

Field Crops, Vegetables, Nurseries: Apply 1-5 kg/ha.Citrus, Apples, Pears, Stone Fruits: Apply 5-10 kg/ha.Grape Vineyards: Apply 8-25 kg/ha.Ornamental Trees: Apply 7-30 g/tree.Shrubs and Bushes: Apply 0.1-0.7 kg/100 bushes.Strawberries: Apply 0.1-0.3 kg/100 plants.

Rates should be judged according to the age of the plant, variety, soil type and other local conditions.

IRRIGATIONWhen used through an irrigation system the appropriate application rate should be selected from the previous selection. This should then be applied via the irrigation system at a rate not greater than 1 kg (dry weight) per 10,000 Litres of water.

PRECAUTIONS1. Keep well sealed and store in original sealed container.2. Wash hands before meals and after work.3. Store away from children, pets, livestock and food stuffs.4. Store dry, away from strong light.5. Do not apply to crops suffering stress such as extreme temperatures, strong winds, etc.

AGRIMAR (UK) PLC9

AGRIMAR ZINC 14%

TECHNICAL DATA

ZINC CHELATE (EDTA) IN SOLUBLE GRANULE FORM. CONTAINS 14% Zn.

Trade Name:AGRIMAR ZINC 14%

Active IngredientZn EDTA 14%

Chemical Name of Active Ingredient:Zinc disodium ethylenediamine tetra acetate.

Molecular Weight:399

Physical Form:Soluble granules, white in colour.

Solubility in Water:300g/l (at 20ºC)

Density:0.70-0.85

Moisture:Not greater than 5%

Packing:1 kg laminated bags; 10 x 1 kgs per carton box.25 kgs carton boxes.

Storage:Store in a cool dry place in original closed container.

HEALTH HAZARDS

a) Effect on eyes – product could cause slight discomfort if allowed to come into contact with delicate eye surfaces, but no permanent damage is likely. It is always advisable to wash eyes if contact with chemicals is suspected.

b) Ingestion – the normally toxic metal ions are held in a complex form (chelated) which reduces their toxicity to a very low level. Risk of injury by accidental ingestion is minimal. In the event of accidental ingestion, the product is not accumulated and is readily eliminated from the body.

c) Effect on skin and mucous membranes – no evidence of irritation or sensitisation.

d) Inhalation – solid products can be dusty and a dust mask should be worn when handling them in bulk, since all dusts are to some extent irritant if inhaled.

FIRST AID

If accidentally ingested – rest patient, give copious amounts of water to drink and seek medical advice.

Skin contamination – wash off with copious amounts of water.

AGRIMAR (UK) PLC10

AGRIMAR COPPER 14%

Copper Chelate (EDTA) in soluble powder form. Contains 14% Cu.

For the correction of copper deficiency in all crops.Recommended for soil and foliar application.

DIRECTIONS FOR USE

Preparation of Solution:Stir 1 part granules into 6 parts water, dilute to the required concentration.

FOLIAR APPLICATION

Timing – to obtain maximum benefit, foliar applications should be started as early as possible in the season, as soon as there is sufficient leaf area to absorb the spray.

Wetting Agent – when this product is applied as a foliar spray alone (i.e. not mixed with other pesticides) it is recommended that a non-ionic wetting agent such as AGRIWET is added to the spray solution.

SOIL APPLICATION

Apply as a course low pressure spray direct to the soil.

Application should always be incorporated into the top few centimetres of soil as soon as possible after application and certainly within the following 1-2 hours. This can be done by harrowing or hoeing in or by irrigation.

Farm Crops:Apply to the soil before the cultivation prior to sowing or planting, or between the rows or through overhead or ground level irrigation systems.

Deep-Rooting Trees and Shrubs:Apply to the soil in a wide circular band under the limit of the full branch spread. For best results, nutrients should be in the root zone before seasonal growth begins. For deep rooting trees in regions which have moderate to high rainfall, apply in mid to late winter to allow the rains to wash in the chelate.

Alternatively, use a pressure injector to get the solution down to the root feeding zone. Injections should be no more than one metre apart, in a wide band directly under the limit of the full branch spread. This should be done at the beginning of the season just before re-growth commences.

If there are weeds or grass growing under the trees, increase the recommended application rate by half as much again.

Shallow-Rooting Crops:Apply to the soil along the rows, beginning at the first signs of seasonal re-growth. In moderate to high rainfall areas, do not wash in. In arid regions, wash in sparingly. If the soil is densely-compacted, the surface should be broken up by hoeing or harrowing before applying.

AGRIMAR (UK) PLC11

AGRIMAR COPPER 14%

RATES OF APPLICATION

The following rates indicate upper and lower limits. Actual amounts used will depend upon the type of plant and on the degree of deficiency:

FOLIAR APPLICATION

Field Crops, General Recommendation:Apply 0.25-0.5 kgs/ha in 200-400 Litres water/ha. For severe deficiencies repeat after two weeks.

Vegetables and Nurseries:Apply 0.2-0.5 kgs/ha in 200-400 Litres water/ha.

Cereals:Apply 0.3-0.5 kgs/ha in 200-400 Litres water/ha.

Fruit Trees:Apply 0.9-0.7 kgs/ha in a repeat high volume spray programme, e.g. 4 applications of 125 gm/ha in 300-500 Litres water/ha.

DO NOT EXCEED A SOLUTION OF 0-1% (1 gram per Litre) WHEN APPLYING AS A FOLIAR SPRAY TO FRUIT CROPS.

SOIL APPLICATION

Field Crops, Vegetables, Nurseries: Apply 0.8-2.5 kg/ha.Fruit Trees: Apply 0.5-5 kg/ha.Ornamental Trees: Apply 7-30 g/tree.Shrubs and Bushes: Apply 0.1-0.7 kg/100 bushes.Strawberries: Apply 0.1-0.7 kg/100 plants.

Rates should be judged according to the age of the plant, variety, soil type and other local conditions.

IRRIGATIONWhen used through an irrigation system the appropriate application rate should be selected from the previous selection. This should then be applied via the irrigation system at a rate not greater than 1 kg (dry weight) per 10,000 Litres of water.

PRECAUTIONS1. Keep well sealed and store in original sealed container.2. Wash hands before meals and after work.3. Store away from children, pets, livestock and food stuffs.4. Store dry, away from strong light.5. Do not apply to crops suffering stress such as extreme temperatures, strong winds, etc.

AGRIMAR (UK) PLC12

AGRIMAR COPPER 14%

TECHNICAL DATA

COPPER CHELATE (EDTA) IN SOLUBLE POWDER FORM. CONTAINS 14% Cu.

Trade Name:AGRIMAR COPPER 14%

Active IngredientCu EDTA 14%

Chemical Name of Active Ingredient:Copper disodium ethylenediamine tetra acetate.

Molecular Weight:397

Physical Form:Soluble granules, blue in colour.

Solubility in Water:357g/l (at 20ºC)

Density:0.70

Moisture:Not greater than 5%

Packing:1 kg laminated bags; 10 x 1 kgs per carton box.25 kgs carton boxes.

Storage:Store in a cool dry place in original closed container.

HEALTH HAZARDS

a) Effect on eyes – product could cause slight discomfort if allowed to come into contact with delicate eye surfaces, but no permanent damage is likely. It is always advisable to wash eyes if contact with chemicals is suspected.

b) Ingestion – the normally toxic metal ions are held in a complex form (chelated) which reduces their toxicity to a very low level. Risk of injury by accidental ingestion is minimal. In the event of accidental ingestion, the product is not accumulated and is readily eliminated from the body.

c) Effect on skin and mucous membranes – no evidence of irritation or sensitisation.

d) Inhalation – solid products can be dusty and a dust mask should be worn when handling them in bulk, since all dusts are to some extent irritant if inhaled.

FIRST AID

If accidentally ingested – rest patient, give copious amounts of water to drink and seek medical advice.

Skin contamination – wash off with copious amounts of water.

AGRIMAR (UK) PLC13

AGRI-MIX NO. 1

A micronutrient mix for correction of nutrient deficiencies in all plants.

Formulated as soluble powder.

Recommended for foliar application and soil application in acid to neutral soils.

DIRECTIONS FOR USE

FOLIAR APPLICATION

Foliar application is recommended for fast correction of deficiencies. Phytotoxic symptoms, such as scorching, may occasionally occur on very sensitive crops after foliar application. If this occurs change to root application.

Timing – to obtain maximum benefit, foliar applications should be started as early as possible in the season, as soon as there is sufficient leaf area to absorb the spray.

In case of severe deficiencies, application may have to be repeated at 7-14 day intervals.

Wetting Agent – when this product is applied as a foliar spray alone (i.e. not mixed with other pesticides) it is recommended that a non-ionic wetting agent such as AGRIWET is added to the spray solution.

SOIL APPLICATION

Dissolve in a convenient amount of water, then apply as a coarse low pressure spray or apply mixed with liquid fertiliser.

Apply to the soil close to plants and tree trunks.

Work well into the soil after application, water carefully after each application to enhance nutrient uptake.

COMPATIBILITY:

The product can be mixed with most other fertilizers and agrochemicals without causing precipitation or scorch problems. In liquid fertilizers the mixture should be used as soon as possible.

AGRIMAR (UK) PLC14

AGRI-MIX NO. 1

COMPOSITION

Element Content Content Form

Boron B 0.40% 4.0 g/kg Mineral SaltCopper Cu 0.15% 1.5 g/kg EDTAIron Fe 5.00% 50.0 g/kg EDTAManganese Mn 2.00% 20.0 g/kg EDTAMolybdenum Mo 0.10% 1.0 g/kg Mineral SaltZinc Zn 0.20% 2.0 g/kg EDTA

AGRI-MIX No. 1 is a micronutrient mix with a higher than usual level of Iron (Fe) which has been designed specifically for use under Middle Eastern conditions.

RATES OF APPLICATION

The following rates give general recommendations. Actual amounts used will depend on the size of bush or tree and on the degree of deficiency.

Crop Foliar Application Soil Application

Cereals 1-2 kg/ha 4-10 kg/ha*Fruit Trees and Shrubs 2-5 kg/ha 4-10 kg/haVegetables 1-4 kg/ha 4-8 kg/haOrnamentals 1-4 kg/ha 2-10 g/plant

*When applying as foliar spray to fruit trees it is important to use a repeat high volume spray programme, e.g. 4 applications of 0.5 kgs in 300-1000 Litres water/ha.

DO NOT EXCEED A SOLUTION OF 0-1% (1 gram per Litre)

Rates should be judged according to the age of the plant, variety, soil type and other local conditions.

PRECAUTIONS1. Keep well sealed and store in original sealed container.2. Wash hands before meals and after work.3. Store away from children, pets, livestock and food stuffs.4. Store dry, away from strong light.5. Do not apply to crops suffering stress such as extreme temperatures, strong winds, etc.

AGRIMAR (UK) PLC15

AGRI-MIX NO. 2

A micronutrient mix for correction of nutrient deficiencies in all plants.

Formulated as soluble powder.

Recommended for foliar application and soil application in acid to neutral soils.

DIRECTIONS FOR USE

FOLIAR APPLICATION

Foliar application is recommended for fast correction of deficiencies. Phytotoxic symptoms, such as scorching, may occasionally occur on very sensitive crops after foliar application. If this occurs change to root application.

Timing – to obtain maximum benefit, foliar applications should be started as early as possible in the season, as soon as there is sufficient leaf area to absorb the spray.

In case of severe deficiencies, application may have to be repeated at 7-14 day intervals.

Wetting Agent – when this product is applied as a foliar spray alone (i.e. not mixed with other pesticides) it is recommended that a non-ionic wetting agent such as AGRIWET is added to the spray solution.

SOIL APPLICATION

Dissolve in a convenient amount of water, then apply as a coarse low pressure spray or apply mixed with liquid fertiliser.

Apply to the soil close to plants and tree trunks.

Work well into the soil after application, water carefully after each application to enhance nutrient uptake.

COMPATIBILITY:

The product can be mixed with most other fertilizers and agrochemicals without causing precipitation or scorch problems. In liquid fertilizers the mixture should be used as soon as possible.

AGRIMAR (UK) PLC16

AGRI-MIX NO. 2

COMPOSITION

Element Content Content Form

Boron B 1.5% 15.0 g/kg Mineral SaltIron Fe 3.8% 38.0 g/kg EDTAMagnesium Mg 1.6% 16.0 g/kg Mineral SaltManganese Mn 4.3% 43.0 g/kg Mineral SaltMolybdenum Mo 0.3% 3.0 g/kg Mineral SaltZinc Zn 0.2% 2.0 g/kg EDTA

AGRI-MIX No. 2 is a micronutrient mix suitable for routine applications to maintain the nutrient status and health of all crops throughout the growing season. Contains Iron EDTA chelate.

RATES OF APPLICATION

The following rates give general recommendations. Actual amounts used will depend on the size of bush or tree and on the degree of deficiency.

Crop Foliar Application Soil Application

Cereals 1-2 kg/ha 4-10 kg/ha*Fruit Trees and Shrubs 2-5 kg/ha 4-10 kg/haVegetables 1-4 kg/ha 4-8 kg/haOrnamentals 1-4 kg/ha 2-10 g/plant

*When applying as foliar spray to fruit trees it is important to use a repeat high volume spray programme, e.g. 4 applications of 0.5 kgs in 300-1000 Litres water/ha.

DO NOT EXCEED A SOLUTION OF 0-1% (1 gram per Litre)

Rates should be judged according to the age of the plant, variety, soil type and other local conditions.

PRECAUTIONS1. Keep well sealed and store in original sealed container.2. Wash hands before meals and after work.3. Store away from children, pets, livestock and food stuffs.4. Store dry, away from strong light.5. Do not apply to crops suffering stress such as extreme temperatures, strong winds, etc.

AGRIMAR (UK) PLC17

NITRO-BOOST

NITRO-BOOST is a liquid formulation designed to give additional nitrogen to crops in a fast acting foliar form. When used during periods of rapid growth or as a routine treatment NITRO-BOOST helps maintain the crop on the path of optimum yield.

Recommended for foliar application.

DIRECTIONS FOR USE

Conventional Spraying:Apply in a minimum of 220 Litres water/ha.

CAD/ULV Spraying:Volume of water can be reduced to 55 Litres/ha.

COMPATIBILITYNITRO-BOOST is compatible with a wide range of fungicides and insecticides. NITRO-BOOST should be added to the water first, followed by the pesticide.

RATES OF APPLICATION

Crop Rate per No. of Stage of CropHectare Applic.

Cereals 5-10 Ltr 3-6 From beginning of tillering up to flowering.

Vegetables, Melons, Squashes, 5-10 Ltr 1-3 As soon as sufficient foliage is Tomatoes,Cucumbers, etc. available for absorption.

Sugar Beet 3-9 Ltr 3-6 From 5-6 leaves onwards.

Maize 5-10 Ltr 1-3 From 20cm height up to maximum 4 weeks later.

Peas 2-3 Ltr 2-4 After peas are more than 15cm high.

Fruit and Ornamentals 6 Ltr 1-3 Before flowering.(under glass and outdoors)

The lower rate is recommended in the case of multiple applications to any one crop.

AGRIMAR (UK) PLC18

NITRO-BOOST

COMPOSITION

Nitrogen N 36% w/v Magnesium Mg 2.4 % w/vManganese Mn 1.3% w/v Copper Cu 0.13% w/v

NITRO-BOOST may be applied through any type of sprayer or through the irrigation system in intensive crops. For optimum effectiveness all the spray mixture should be applied to the plant foliage.

NITRO-BOOST is independent of weather conditions, but best results will be obtained if applied early morning or late evening. Do not apply in bright sunlight.

PRECAUTIONS1. Keep well sealed and store in original sealed container.2. Wash hands before meals and after work.3. Store away from children, pets, livestock and food stuffs.4. Store dry, away from strong light.5. Do not apply to crops suffering stress such as extreme temperatures, strong winds, etc.

Packed in 5 litre plastic bottles;4 x 5 Litres per carton.

AGRIMAR (UK) PLC19

AGRI-FOL

Liquid Foliar Fertiliser. Guaranteed analysis 12-6-6.

A complete foliar nutrient for application to all crops.

Recommended for foliar and soil application.

DIRECTIONS FOR USE

AGRI-FOL mixes readily with water. Stir when mixing. Spray when crop is actively growing. During hot weather spray at coolest part of the day, i.e. early morning or late evening.

DO NOT APPLY IN DIRECT SUNLIGHT.

COMPATIBILITYAGRI-FOL is compatible with a wide range of fungicides and insecticides. AGRI-FOL should be added to the water first, followed by the pesticide.

RATES OF APPLICATION

FOLIAR APPLICATION – All Crops:Apply 2.5 Litres/ha in minimum 225 Litres water/ha. Begin when leaves are large enough to absorb the nutrients and continue every 14-21 days until crop is mature.

SOIL APPLICATION – All Crops:Apply 50 Litres/ha in 1120 Litres water/ha before planting. Work lightly into the soil.

ROW APPLICATION – All Crops:Apply 5 Litres/ha in 1120 Litres water/ha at least 5cm to the side and 5cm below the row of seeds.

AGRIMAR (UK) PLC20

AGRI-FOL

COMPOSITION

Water Soluble Organic Nitrogen (urea) N 12%Available Phosphoric Acid P 6%Water Soluble Potash K 6%Magnesium Mg 0.10%Iron Fe 0.10%Manganese Mn 0.05%Copper Cu 0.05%Zinc Zn 0.05%Boron B 0.02%Molybdenum Mo 0.0005%Cobalt Co 0.0005%

CAUTIONAGRI-FOL is acidic. Avoid contact with skin, eyes or clothing. Rinse out equipment after spraying.

PRECAUTIONS1. Keep well sealed and store in original sealed container.2. Wash hands before meals and after work.3. Store away from children, pets, livestock and food stuffs.4. Store dry, away from strong light.5. Do not apply to crops suffering stress such as extreme temperatures, strong winds, etc.

AGRIMAR (UK) PLC21