CMH-WM-V-AMODEL
AIR CONDITIONING SYSTEMS
CMH-WM-V-A
MEES18K070 1
CONTENTS Hydro unit
I.Hydro unit
1. SPECIFICATIONS.................................................................................................................................... 2
2. EXTERNAL DIMENSIONS ....................................................................................................................... 5
3. CENTER OF GRAVITY ............................................................................................................................ 7
4. ELECTRICAL WIRING DIAGRAMS ......................................................................................................... 8
5. SOUND LEVELS ...................................................................................................................................... 9
5-1. Sound levels .................................................................................................................................... 95-2. NC curves ........................................................................................................................................ 9
6. ELECTRICAL CHARACTERISTICS......................................................................................................... 10
7. INSTALLATION ........................................................................................................................................ 11
7-1. Lifting method .................................................................................................................................. 11
8. OPTIONAL PARTS................................................................................................................................... 12
8-1. Drain pan ......................................................................................................................................... 12
0000005070.BOOK 1 ページ 2018年11月15日 木曜日 午後6時41分
MEES18K070
Hyd
ro u
nit
2
1. SPECIFICATIONS Hydro unit
I.Hydro unit1. SPECIFICATIONS
Model name CMH-WM250V-A
Power source 1-phase 220-230-240 V
50 Hz 60 Hz
Power input Cooling kW 0.74/0.74/0.74 0.74/0.74/0.74
(220/230/240) Heating kW 0.74/0.74/0.74 0.74/0.74/0.74
Current input Cooling A 3.84/3.67/3.52 3.84/3.67/3.52
(220/230/240) Heating A 3.84/3.67/3.52 3.84/3.67/3.52
Sound pressure level (measured in anechoice room) dB <A> 60
Applicable temperature range of installation site °C (D.B.) -5~52
External finish Pre-coated galvanized steel sheets
(Lower part drain pan: Pre-coated galvanized sheets + powder coating)
Connectable outdoor/heat source unit capacity (E)M200~250
External dimension H x W x D mm 660 x 920 x 740
in. 25-63/64 x 36-7/32 x 29-9/64
Refrigerant piping diameter
To outdoor/heat source unit Connectable outdoor/heat source unit capacity
M200 M250 EM200 EM250
Liquid pipe mm (in.) 9.52 (3/8) 9.52 (3/8) 9.52 (3/8) 9.52 (3/8)
O.D. Brazed Brazed Brazed Brazed
Gas pipe mm (in.) 22.2 (7/8) 22.2 (7/8) 22.2 (7/8) 22.2 (7/8)
O.D. Brazed Brazed Brazed Brazed
Water piping diameter
To Indoor unit
Inlet Pipemm (in.)
I.D.40 (1-1/2) housing joint
Outlet Pipemm (in.)
I.D.40 (1-1/2) housing joint
Net weight kg (lbs) 112 (247) [119 (263) with water]
Standardattachment
Document –
Accessories Y-type strainer, Auto air vent valve, Joint, Elbow, Pipe
Optional parts Drain pan (PAC-SH01DP-E)
Note 1.Works not included: Installation/foundation work, electrical connection work, duct work, insulation work, power source switch, and other items are not specified in this specifications.
2.The equipment is for R32 refrigerant.
3.Install this product in a location where noise (refrigerant noise) emitted by the unit will not disturb the neighbors. (For use in quiet environments with low background noise, position the Hydro unit at least 5 m away from any indoor units.)
4.Please install the Hydro unit in a place where noise will not be an issue.
5.Please attach an expansion vessel (field supply).
6.Use copper, plastic, steel, or stainless steel pipes for the water circuit. Furthermore, when using copper pipe-work use a non-oxidative brazing method. Oxidation of the pipe-work will reduce the pump life.
7.When brazing the pipes, be sure to braze, after covering a wet cloth to the insulation pipes of the units in order to prevent it from burning and shrinking by heat.
8.Please install an air purge valve where air will gather in the water circuit.
9.Please install a pressure reducing valve and a strainer on the water supply to the Hydro unit.
10.Please refer to the databook or the installation manual for the specified water quality.
11.Please always make water circulate or pull out the circulation water completely when not using it. *Please do not use it as a drinking water.
12.Please do not use ground water and well water.
13.When installing the Hydro unit in an environment which may drop below 0 °C, please add antifreeze to the circulating water. (Refer to the data-book and the installation manual).
14.R32 is flammable, and certain restrictions apply to the installation of units. When installing new units, moving the existing units, or changing the layout of the room, ensure that installation restrictions are observed. For detail, refer to the section in the Databook on installation restrictions.
15.Drain or condensation water will be discharged from hydro units during test run. If this will be a problem, install a separately sold drain pan.
16.Do not install the unit where it could be salt-damaged.
0000005070.BOOK 2 ページ 2018年11月15日 木曜日 午後6時41分
MEES18K070
Hyd
ro u
nit
3
1. SPECIFICATIONS Hydro unit
Model name CMH-WM350V-A
Power source 1-phase 220-230-240 V
50 Hz 60 Hz
Power input Cooling kW 0.90/0.90/0.90 0.90/0.90/0.90
(220/230/240) Heating kW 0.90/0.90/0.90 0.90/0.90/0.90
Current input Cooling A 4.69/4.48/4.30 4.69/4.48/4.30
(220/230/240) Heating A 4.69/4.48/4.30 4.69/4.48/4.30
Sound pressure level (measured in anechoice room) dB <A> 60
Applicable temperature range of installation site °C (D.B.) -5~52
External finish Pre-coated galvanized steel sheets
(Lower part drain pan: Pre-coated galvanized sheets + powder coating)
Connectable outdoor/heat source unit capacity (E)M300~350
External dimension H x W x D mm 660 x 920 x 740
in. 25-63/64 x 36-7/32 x 29-9/64
Refrigerant piping diameter
To outdoor/heat source unit Connectable outdoor/heat source unit capacity
M300 M350 EM300 EM350
Liquid pipe mm (in.) 9.52 (3/8) 12.7 (1/2) 9.52 (3/8) 12.7 (1/2)
O.D. Brazed Brazed Brazed Brazed
Gas pipe mm (in.) 22.2 (7/8) 28.58 (1-1/8) 28.58 (1-1/8) 28.58 (1-1/8)
O.D. Brazed Brazed Brazed Brazed
Water piping diameter
To Indoor unit
Inlet Pipemm (in.)
I.D.40 (1-1/2) housing joint
Outlet Pipemm (in.)
I.D.40 (1-1/2) housing joint
Net weight kg (lbs) 122 (269) [126 (278) with water]
Standardattachment
Document –
Accessories Y-type strainer, Auto air vent valve, Joint, Elbow, Pipe
Optional parts Drain pan (PAC-SH01DP-E)
Note 1.Works not included: Installation/foundation work, electrical connection work, duct work, insulation work, power source switch, and other items are not specified in this specifications.
2.The equipment is for R32 refrigerant.
3.Install this product in a location where noise (refrigerant noise) emitted by the unit will not disturb the neighbors. (For use in quiet environments with low background noise, position the Hydro unit at least 5 m away from any indoor units.)
4.Please install the Hydro unit in a place where noise will not be an issue.
5.Please attach an expansion vessel (field supply).
6.Use copper, plastic, steel, or stainless steel pipes for the water circuit. Furthermore, when using copper pipe-work use a non-oxidative brazing method. Oxidation of the pipe-work will reduce the pump life.
7.When brazing the pipes, be sure to braze, after covering a wet cloth to the insulation pipes of the units in order to prevent it from burning and shrinking by heat.
8.Please install an air purge valve where air will gather in the water circuit.
9.Please install a pressure reducing valve and a strainer on the water supply to the Hydro unit.
10.Please refer to the databook or the installation manual for the specified water quality.
11.Please always make water circulate or pull out the circulation water completely when not using it. *Please do not use it as a drinking water.
12.Please do not use ground water and well water.
13.When installing the Hydro unit in an environment which may drop below 0 °C, please add antifreeze to the circulating water. (Refer to the data-book and the installation manual).
14.R32 is flammable, and certain restrictions apply to the installation of units. When installing new units, moving the existing units, or changing the layout of the room, ensure that installation restrictions are observed. For detail, refer to the section in the Databook on installation restrictions.
15.Drain or condensation water will be discharged from hydro units during test run. If this will be a problem, install a separately sold drain pan.
16.Do not install the unit where it could be salt-damaged.
0000005070.BOOK 3 ページ 2018年11月15日 木曜日 午後6時41分
MEES18K070
Hyd
ro u
nit
4
1. SPECIFICATIONS Hydro unit
Model name CMH-WM500V-A
Power source 1-phase 220-230-240 V
50 Hz 60 Hz
Power input Cooling kW 1.06/1.06/1.06 1.06/1.06/1.06
(220/230/240) Heating kW 1.06/1.06/1.06 1.06/1.06/1.06
Current input Cooling A 5.47/5.23/5.02 5.47/5.23/5.02
(220/230/240) Heating A 5.47/5.23/5.02 5.47/5.23/5.02
Sound pressure level (measured in anechoice room) dB <A> 60
Applicable temperature range of installation site °C (D.B.) -5~52
External finish Pre-coated galvanized steel sheets
(Lower part drain pan: Pre-coated galvanized sheets + powder coating)
Connectable outdoor/heat source unit capacity (E)M400~500
External dimension H x W x D mm 660 x 920 x 740
in. 25-63/64 x 36-7/32 x 29-9/64
Refrigerant piping diameter
To outdoor/heat source unit Connectable outdoor/heat source unit capacity
M400 M450/500 EM400 EM450/500
Liquid pipe mm (in.) 12.7 (1/2) 15.88 (5/8) 12.7 (1/2) 15.88 (5/8)
O.D. Brazed Brazed Brazed Brazed
Gas pipe mm (in.) 28.58 (1-1/8) 28.58 (1-1/8) 28.58 (1-1/8) 28.58 (1-1/8)
O.D. Brazed Brazed Brazed Brazed
Water piping diameter
To Indoor unit
Inlet Pipemm (in.)
I.D.50 (2) housing joint
Outlet Pipemm (in.)
I.D.50 (2) housing joint
Net weight kg (lbs) 143 (316) [157 (347) with water]
Standardattachment
Document –
Accessories Y-type strainer, Auto air vent valve, Joint, Elbow, Pipe
Optional parts Drain pan (PAC-SH01DP-E)
Note 1.Works not included: Installation/foundation work, electrical connection work, duct work, insulation work, power source switch, and other items are not specified in this specifications.
2.The equipment is for R32 refrigerant.
3.Install this product in a location where noise (refrigerant noise) emitted by the unit will not disturb the neighbors. (For use in quiet environments with low background noise, position the Hydro unit at least 5 m away from any indoor units.)
4.Please install the Hydro unit in a place where noise will not be an issue.
5.Please attach an expansion vessel (field supply).
6.Use copper, plastic, steel, or stainless steel pipes for the water circuit. Furthermore, when using copper pipe-work use a non-oxidative brazing method. Oxidation of the pipe-work will reduce the pump life.
7.When brazing the pipes, be sure to braze, after covering a wet cloth to the insulation pipes of the units in order to prevent it from burning and shrinking by heat.
8.Please install an air purge valve where air will gather in the water circuit.
9.Please install a pressure reducing valve and a strainer on the water supply to the Hydro unit.
10.Please refer to the databook or the installation manual for the specified water quality.
11.Please always make water circulate or pull out the circulation water completely when not using it. *Please do not use it as a drinking water.
12.Please do not use ground water and well water.
13.When installing the Hydro unit in an environment which may drop below 0 °C, please add antifreeze to the circulating water. (Refer to the data-book and the installation manual).
14.R32 is flammable, and certain restrictions apply to the installation of units. When installing new units, moving the existing units, or changing the layout of the room, ensure that installation restrictions are observed. For detail, refer to the section in the Databook on installation restrictions.
15.Drain or condensation water will be discharged from hydro units during test run. If this will be a problem, install a separately sold drain pan.
16.Do not install the unit where it could be salt-damaged.
0000005070.BOOK 4 ページ 2018年11月15日 木曜日 午後6時41分
MEES18K070
Hyd
ro u
nit
5
2. EXTERNAL DIMENSIONS Hydro unit
2. EXTERNAL DIMENSIONS
CMH-WM250, 350, 500V-A Unit: mm
1 2 43 5 6 7 8NO.
102
148
155
760
8080
681(678~684)29.5
105
150
290
968421550 100 94
120
83 92
150 30
0
(740)
192
230
345
175
29.5
170223
160
135 21
7
190310
400518
A
920
740 660
450 450
35
1 234
7
5
68
Fron
t vie
w
Bot
tom
vie
w
Rig
ht S
ide
view
Rea
r vie
w
Wat
er p
ipe(
EX
P.Ve
ssel
)ø2
2.0(
use
atta
chm
ent p
ipe)
[fiel
d su
pply
]
Wat
er in
let
WM
250,
350:
1-1/
2inc
h ho
usin
g jo
int
WM
500:
2inc
h ho
usin
g jo
int
Wat
er p
ipe(
Inle
t)ø2
2.0(
use
atta
chm
ent p
ipe)
[fiel
d su
pply
]
Wat
er o
utle
tW
M25
0,35
0:1-
1/2i
nch
hous
ing
join
tW
M50
0:2i
nch
hous
ing
join
tC
ontro
l box
Ser
vice
pan
elS
ervi
ce p
anel
(Mounting pitch)
(Mou
ntin
g pi
tch)
Slin
g ho
leY-
type
stra
iner
(Acc
esso
ry)
Join
t(Acc
esso
ry)
Top
view
Ref
riger
ant
pipe
<G
as>
Ref
riger
ant
pipe
<Li
quid
>
Serv
ice s
pace
Serv
ice s
pace
Det
ail o
f X s
ectio
n
For tr
ansm
ission
cable
s
For w
ires
For p
ipes
Usa
geS
peci
ficat
ions
Fro
nt thr
ough
hole
Botto
m thr
ough
hole
Front
throu
gh ho
le
Front
throu
gh ho
le
Botto
m thr
ough
hole
Botto
m thr
ough
hole
Front
throu
gh ho
le
148
× 84
Kno
ckou
t hole
ø28
Knoc
kout
hole
ø2
8 Kn
ocko
ut h
ole
ø28
Knoc
kout
hole
ø2
8 Kn
ocko
ut h
ole
ø35
Knoc
kout
hole
150
× 94
Kno
ckou
t hole
ø35
Knoc
kout
hole
Bo
ttom
throu
gh ho
le
Mod
elD
iam
eter
Ref
riger
ant p
ipe
WM
350
ø22.2
Braz
ed
ø9.5
2 Br
azed
W
M25
0
Con
nect
ing
pipe
spe
cific
atio
ns
Liqu
idG
as
ø12.
7 Br
azed
ø15.
88 B
raze
dø2
5.4 Br
azed
WM
500
(ø28.6
Braz
ed) *
1
Mod
el
WM
350
256
WM
250
A 281
WM
500
Not
e 1.
Ple
ase
refe
r to
the
next
pag
e fo
r inf
orm
atio
n re
gard
ing
nece
ssar
y fo
unda
tion
wor
k.2.
Take
not
ice
of s
ervi
ce s
pace
as
follo
ws.
(Ple
ase
give
atte
ntio
n no
t to
occu
py s
ervi
ce s
pace
by
letti
ng d
ucts
and
pip
es th
roug
h.)
3.A
t bra
zing
of p
ipes
, wra
p th
e pi
pew
ith w
et c
loth
and
kee
p th
e te
mpe
ratu
re o
f pip
e un
der 1
20°C
.4.
If de
w c
onde
nsat
ion
wat
er d
ropp
ing
from
hol
es o
n th
e un
it ba
seis
con
cern
ed, p
leas
e in
stal
l the
dra
in p
an.
5.In
stal
l thi
s pr
oduc
t in
a lo
catio
n w
here
noi
seem
itted
by
the
unit
will
not
dis
turb
the
neig
hbor
s.
<Acc
esso
ries>
· Y-ty
pe s
train
er(R
c1-1
/4)·
··W
M25
0,35
0 1p
c.· Y
-type
stra
iner
(Rc1
-1/2
)···
WM
500
1pc.
· Joi
nt(F
rom
Rc1
-1/4
to 1
-1/2
inch
hou
sing
join
t)··
·WM
250,
350
1pc.
· Joi
nt(F
rom
Rc1
-1/2
to 2
inch
hou
sing
join
t)··
·WM
500
1pc.
· Elb
ow(ID
ø25.
4×O
Dø2
5.4)
···W
M35
0,50
0 1p
c.· P
ipe
(IDø2
5.4×
OD
ø28.
6)··
·WM
350,
500
1pc.
· Aut
o ai
r ven
t val
ve(G
3/8)
···1
pc.
A P
RE
VIO
US
NO
TIC
E A
ND
MIG
HT
CH
AN
GE
.TH
E S
PE
CIF
ICAT
ION
OF
THE
PR
OD
UC
T IS
FO
R T
HE
IMP
RO
VE
ME
NT
*1 U
sing d
iffere
nce d
iamete
r pipe
joint
.*2
Con
nect
the re
friger
ant p
ipe
acco
rding
to th
e Ins
tallat
ion M
anua
l.*3
Indic
ates d
imen
sions
and c
onne
ction
spec
ificati
ons
in the
case
the u
nit is
used
in co
mbina
tion w
ith
other
outdo
or un
its.
2×2-
14×2
0 O
val h
ole
Ref
riger
ant p
ipe
<Liq
uid>
Ref
riger
ant p
ipe
<Gas
>
X
Cut
ting
poin
t
0000005070.BOOK 5 ページ 2018年11月15日 木曜日 午後6時41分
MEES18K070
Hyd
ro u
nit
6
2. EXTERNAL DIMENSIONS Hydro unit
CMH-WM250, 350, 500V-A Unit: mm
30mm max
M10 a
ncho
r bolt
<field
supp
ly req
uired
>
Fig.
A
Fixing
plate
<field
supp
ly req
uired
>Fi
g.B
1. F
ound
atio
n w
ork
1 Ta
ke in
to c
onsi
dera
tion
the
surfa
ce s
treng
th, w
ater
dra
inag
e ro
ute,
pipi
ng ro
ute,
and
wiri
ng ro
ute
whe
n pr
epar
ing
the
inst
alla
tion
site
.<N
ote
that
the
drai
n w
ater
com
es o
ut o
f the
uni
t dur
ing
oper
atio
n.>
2 B
uild
the
foun
datio
n in
suc
h w
ay th
at th
e co
rner
of t
he in
stal
latio
n le
g is
secu
rely
sup
porte
d as
sho
wn
in th
e rig
ht fi
gure
.(Fig
.A)
Whe
n us
ing
a ru
bber
isol
atin
g cu
shio
n, p
leas
e en
sure
it is
larg
e en
ough
to c
over
the
entir
e w
idth
of e
ach
of th
e un
it's
legs
.3
The
prot
rusi
on le
ngth
of t
he a
ncho
r bol
t mus
t not
exc
eed
30m
m.(F
ig.A
)4
Use
four
fixi
ng p
late
s as
sho
wn
in th
e rig
ht fi
gure
<fie
ld s
uppl
y re
quire
d>w
hen
usin
g po
st-in
stal
led
anch
or b
olts
.(Fig
.B)
5 To
pre
vent
sm
all a
nim
als
and
wat
er a
nd s
now
from
ent
erin
g th
e un
it an
d da
mag
ing
its p
arts
,cl
ose
the
gap
arou
nd th
e ed
ges
of th
roug
h ho
les
for p
ipes
and
wire
s w
ithfil
ler p
late
s <f
ield
sup
ply
requ
ired>
.6
Whe
n th
e pi
pes
or c
able
s ar
e ro
uted
at t
he b
otto
m o
f the
uni
t,m
ake
sure
that
the
thro
ugh
hole
at t
he b
ase
of th
e un
it do
es n
ot g
et b
lock
edw
ith th
e in
stal
latio
n ba
se.
7 R
efer
to th
e In
stal
latio
n M
anua
l whe
n in
stal
ling
units
on
an in
stal
latio
n ba
se.
0000005070.BOOK 6 ページ 2018年11月15日 木曜日 午後6時41分
MEES18K070
Hyd
ro u
nit
7
3. CENTER OF GRAVITY Hydro unit
3. CENTER OF GRAVITY
CMH-WM250, 350, 500V-A
Model
CMH-WM250V-A
CMH-WM350V-A
CMH-WM500V-A
X
443
433
392
Y
256
256
260
Z
398
394
406
Unit: mm
XY
Z
740 9066
0
0000005070.BOOK 7 ページ 2018年11月15日 木曜日 午後6時41分
MEES18K070
Hyd
ro u
nit
8
4. ELECTRICAL WIRING DIAGRAMS Hydro unit
4. ELECTRICAL WIRING DIAGRAMS
CMH-WM250, 350, 500V-A
t°t°
t°t°
U
U
CN
110
FT00
1
FT00
2
SC-T
SC-R
CN
DC
CNVD
C
CN2
CN
17V
CN
2
CN
301
CN
601
CN
001
CN
801
CN
002
CN
802
CN
303
CN
305
CN
RS
T
CN
401
CN
301
CN
412
CN
AC
CN
FG
CT2
SC-S
SC-P
1
SC-P
2
CN4
CN
4
CN10
2CN
101
INV-
BO
AR
D
CN
401
CN
402
CN
411
CN
413
PS
-BO
AR
DM
AIN
-BO
AR
D
CN
701
LEVM
12
31
24
53
12
56 4 3 2 112
1 2 3 1 2 3 51 2 4
31
2
CN30
6
35
42
1
35 4 2 11212234 112 56 4 3 2 1
12
12
31
2
23 1
32
14
12
35
12
4
12
31
2
234 1
LN
21 3 4 5 6
TH32
TH35
TH11
TH13
12
31
23
12
3PS
LWPS
HW
12
AC
L
SC-U
SC-V
SC-W
SV
3
whi
te
yello
w
H
WV
UM
S 3~ WP
whi
te
red
gree
n
blue
gree
n
gree
n
gree
nye
llow
red
red
blac
k
whi
te
whi
te
whi
te
pink
blac
k
blue
whi
te
red
blue
red
yello
wbla
ckgr
een
red
gree
n
red
red
2
whi
tebl
ack
red
white
black
gree
nw
hite re
d
23 1
31
4
M1
M2
TB3
X01
X02
F3.
15A
CTX
52
PTC
CT1
DS
A
Indo
or/o
utdo
orTr
ansm
issi
on L
ine
SWU0
1SW
U02
LD00
1
SWP0
2
SWP0
1UP DO
WNSW
P03
TB01
LED4
:CPU
in o
pera
tion
LED1
:Nor
mal
oper
ation
(lit)
/Erro
r(blin
k)
pow
er s
uppl
y~2
20V-
240V
50H
z/60
Hz
LED
02:N
orm
al o
pera
tion(
lit)
/Err
or(b
link)
LED
01:C
PU
in o
pera
tion
PS
R
LD60
1:po
wer
sup
ply
Prim
ary
curre
ntde
tect
ion
circu
it
31
54
2
TB-N
TB-P
RY
PN
12
Z1
yello
wC
N40
3F 6.
3AF1
5A
Not
e:1.
The
brok
en li
nes
indi
cate
the
field
-sup
plie
d pa
rts,a
nd fi
eld
wor
k.2.
TB3
is tr
ansm
issi
on te
rmin
al b
lock
.N
ever
con
nect
pow
er li
ne to
it.
3.C
ontro
l box
hou
ses
high
-vol
tage
par
ts.
Befo
re in
spec
ting
the
insi
de o
f the
con
trol b
ox, t
urn
off t
he p
ower
,ke
ep th
e un
it of
f for
at l
east
10
min
utes
, and
con
firm
that
the
volta
geof
the
conn
ecto
r RYP
N o
n IN
V-BO
ARD
has
dro
pped
to D
C20
V or
less
.4.
The
initi
al s
et v
alue
s of
sw
itch
on M
AIN
BO
ARD
are
as
follo
ws.
SWU
01:0
SWU
02:0
(Sym
bol e
xpla
natio
n)
LEV
AC
L
PS
HW
,PS
LWPr
essu
re se
nsor
(wate
r)
Sym
bol
Nam
eA
C re
acto
r
Exp
ansi
on v
alve
WP
Pum
p
Nam
eS
ymbo
l
HE
lect
ric h
eate
r
PS
RP
ress
ure
sens
or(r
efrig
eran
t)
Fuse
F
Sol
enoi
d va
lve
SV
(Ant
ifree
ze)
TB01
Term
inal
blo
ck(fo
r pow
er s
ourc
e)TB
3Te
rmin
al b
lock
(for T
rans
mis
sion
)TH
11,T
H12
,TH
32,T
H35
Ther
mis
ter s
enso
r
Z1Fu
nctio
n se
tting
conn
ecto
r
987654321
ON
ON
SW01
1
ON
10
987654321 10
87654321
SW00
1SW
002
SW
1
12
34
ON
SW1
12
34
56
ON
0000005070.BOOK 8 ページ 2018年11月15日 木曜日 午後6時41分
MEES18K070
Hyd
ro u
nit
9
5. SOUND LEVELS Hydro unit
5. SOUND LEVELS5-1. Sound levels(Measured point)
5-2. NC curves
*Measured in anechoic room.
1m
Measurement location
10
20
30
40
50
60
70
80
90
63 125 250 500 1k 2k 4k 8k
NC-40
NC-30
NC-20
NC-60
NC-70
NC-50
Power Source: 220-240V (50/60Hz)
Octave band central frequency (Hz)
Oct
ave
band
sou
nd le
vel (
dB)
Approximate minimumaudible limit oncontinuous noise
CMH-WM250, 350, 500V-A
0000005070.BOOK 9 ページ 2018年11月15日 木曜日 午後6時41分
MEES18K070
Hyd
ro u
nit
10
6. ELECTRICAL CHARACTERISTICS Hydro unit
6. ELECTRICAL CHARACTERISTICS
Symbols: MCA: Max. Circuit Amps, MFA: Max. Fuse Amps, RLA: Rated Load Amps
Hydro unitPower supply
RLA(A)Hz Volts Range+-10% MCA(A) MFA(A)
CMH-WM250V-A 50/60
220Max.: 264VMin.: 198V
4.40 15
3.84
230 3.67
240 3.52
CMH-WM350V-A 50/60
220Max.: 264VMin.: 198V
5.38 15
4.69
230 4.48
240 4.30
CMH-WM500V-A 50/60
220Max.: 264VMin.: 198V
6.28 15
5.47
230 5.23
240 5.02
0000005070.BOOK 10 ページ 2018年11月15日 木曜日 午後6時41分
MEES18K070
Hyd
ro u
nit
11
7. INSTALLATION Hydro unit
7. INSTALLATION7-1. Lifting method
When hanging the unit for transportation Use hanging holes to hang the unit.
Keep the ropes from coming into contact with the water supply and expansion vessel pipes while the unit is being hung.
Protective padProtective pad
Protective pad
Water-supply pipes
Unit
Expansion vessel
Out of contact with rope
Hanging holes
pipes
40°≤
0000005070.BOOK 11 ページ 2018年11月15日 木曜日 午後6時41分
MEES18K070
Hyd
ro u
nit
12
8. OPTIONAL PARTS Hydro unit
8. OPTIONAL PARTS8-1. Drain pan
Drain pan
CMH-WM250, 350, 500V-A PAC-SH01DP-E
CMH-WM-A
base
Hydro unit
Drain pan PAC-SH01DP-E
PAC-SH01DP-EItem
Quantity 1 2 10 (Spare included)
Shape
Detailed installation information should be referred to its Installation Manual.
ItemQuantity
Shape
Drain pan Additional panel
5 (Spare included) 12 (Spare included)Washer M10 Screw 5 × 10 KNURLED
Nut M10
0000005070.BOOK 12 ページ 2018年11月15日 木曜日 午後6時41分
MEES18K070New publication effective Nov. 2018
Specifications subject to change without notice
WarningDo not use refrigerant other than the type indicated in the manuals provided with the unit and on the nameplate.- Doing so may cause the unit or pipes to burst, or result in explosion or fire during use, repair, or at the time of disposal of the unit.- It may also be in violation of applicable laws.- MITSUBISHI ELECTRIC CORPORATION cannot be held responsible for malfunctions or accidents resulting from the use of the wrong
type of refrigerant.Our air conditioning equipment and heat pumps contain a fluorinated greenhouse gas, R32.
■
■