Page 1 of 2 TB-116 / August 5, 2015 Airmar B75 transducer compatibility with BSM-3 Product: 000-12492-001, 000-12493-001, 000-12494-001, 000-12495-001, 000-12496-001, 000-12497-001, Product Description: Airmar B75 and BSM-3 Software Version: ALL Effective Date: July 2015 Inspect/Update Current Inventory: No Airmar® B75 Wiring All Navico® Airmar B75 transducers shipping with the blue 7-pin connector have been hard- wired for connection to SonarHub modules. This wiring does not match the required wiring for connection to the connectors on Simrad® BSM-3 modules. If directly connected to the port on a BSM-3, an Airmar B75 will fail to report its XID and temperature readings to the BSM-3. It is recommended to cut off the hard-wired blue 7-pin connector attached to the B75 and use the wires inside the cable to wire it directly to the terminal blocks inside the BSM-3, thus bypassing the connectors on the module. This does not affect other models of Airmar transducers. For connecting the bare wires, follow this diagram: ORANGE BLUE/ WHITE BROWN & WHITE BLACK/ WHITE SHIELD INNER SHIELD OUTER B75L ORANGE BLUE BROWN & WHITE BLACK SHIELD INNER SHIELD OUTER B75H B75M
Transcript
Page 1 of 2
TB-116 / August 5, 2015
Airmar B75 transducer compatibility with BSM-3 Product: 000-12492-001, 000-12493-001, 000-12494-001,
000-12495-001, 000-12496-001, 000-12497-001,
Product Description: Airmar B75 and BSM-3
Software Version: ALL
Effective Date: July 2015
Inspect/Update Current Inventory: No
Airmar® B75 Wiring
All Navico® Airmar B75 transducers shipping with the blue 7-pin connector have been hard-
wired for connection to SonarHub modules. This wiring does not match the required wiring for
connection to the connectors on Simrad® BSM-3 modules. If directly connected to the port on a
BSM-3, an Airmar B75 will fail to report its XID and temperature readings to the BSM-3.
It is recommended to cut off the hard-wired blue 7-pin connector attached to the B75 and use
the wires inside the cable to wire it directly to the terminal blocks inside the BSM-3, thus
bypassing the connectors on the module. This does not affect other models of Airmar
transducers.
For connecting the bare wires, follow this diagram:
ORANGE
BLUE/WHITE
BROWN&
WHITE
BLACK/WHITE
SHIELDINNER
SHIELDOUTER
B75L
ORANGE
BLUEBROWN&
WHITE
BLACK
SHIELDINNERSHIELD
OUTER
B75HB75M
Page 2 of 2
For More Information:
U.S. Based Resellers Technical and Order Support: (800) 324-4737
Canada Based Resellers Technical Support: (855) 361-1564
You may also send any inquiries via email to the addresses listed below, according to your sales-group classification:
Product Description: All Zeus2 Multi-Function Displays (MFD)
All Zeus2 Glass Helm Processors
Software Version: Zeus2_W-3.0-52.1.106-32282-r1
Zeus2_Black_Box-3.0-52.1.106-32282-r1
Effective Date: July 2015
Inspect/Update Current Inventory: Yes
B&G is pleased to announce that new software has been released for all Zeus2 multifunction displays. This is a major release that incorporates some great new features and improvements.
The software, Zeus2_W-3.0-52.1.106-32282-r1-Standard-1.upd or Zeus2_Black_Box-3.0-52.1.106-32282-r1-Standard-1.upd, can be downloaded from the Zeus2 downloads page on the B&G website www.bandg.com
New Features Race Panel
Race Panel contains a new set of race specific features available directly from the Home page or within a panel. Race Panel adds:
Integration with H5000 Start Line feature
New Scaled Start Line View with 1 boat length grid and zero burn line for the perfect start (H5000 systems only)
"What If?" panel to allow assessment of wind changes on strategy (all systems with relevant data, H5000 systems use polar data if available)
Start Line is also available to overlay on Chart panels for complete navigational awareness
Added Mean TWD data - TWD averaged over time period
Added Wind Phase - difference between TWD and Mean TWD
Added Lift/Header - Wind Phase adjusted to be relative to current tack
All available as data items for display
Expanded H5000 system support
H5000 CPU Settings available via Zeus
H5000 CPU IP address available via Zeus
Added full support, including commissioning, for H5000 Pilot Waypoint/Route enhancements
Route summary includes TWA for each leg
Option to enter waypoints via range/bearing added
Added Windward/Leeward quick course builder feature New instrument panels
3 new instrument panels added for full screen, 2-way and 4-way split screens Race Timer control
Race Timer has been added to Trip Log page as an additional tab allowing all trip features to be controlled from one location
Jeppesen MAX-N+ 2015 charting features
Full-Featured Vector Charts: Chart detail including Depth Areas and Contours, Spot Soundings, NavAids, Light Sectors, Wrecks/Obstructions, Small Craft Facilities and more
Aerial Photos: High-Definition Photos & Diagrams of ports, marinas and significant navigational marks
Custom Shaded Depths: Shaded depths make it easy to distinguish different water depths.
Dynamic Raster: Traditional “paper chart” look with unique ability to access information on buoys, lights and other details
Easy Routing: Automatically plots the shortest, safest route based on detailed chart data and vessel information. * Available only with MAX-N+ outside the Americas
Tides & Currents: Presents the time, water level and direction of tides with Tide Level graphs and indicates predicted current time, direction and strength of currents with Current Flow graphs and colored arrows
Harbor and Approach Details: Lets boaters approach any harbor and inlet with confidence
Detailed Marina Port Plans: Docking in an unfamiliar port is no problem, when you have precise layouts of thousands of marinas, including slip spaces, restricted areas, and other valuable navigation information
Page 3 of 4
Password protection for system settings
RTM 3.0 includes an optional PIN protection feature for system settings, files and GoFree Shop access. A PIN code can be applied under HOME>SETTINGS>PIN CODE. The PIN code is a 4-digit number and if forgotten the user will either need to perform a hard reset or contact customer support for an unlock code.
Fixes and Improvements Lockup on start up
An issue was identified on some Zeus2 displays that resulted in the unit reaching the boot splash screen, locking up then rebooting. This issue has been resolved in RTM 3.0.
Touch screen improvements
Improvements have been made to the touch screen drivers to resolve intermittent touch on some Zeus2 displays.
WIFI-1 software
RTM-3.0 has an important integrated software upgrade for the WIFI-1 module. After RTM 3.0 has been installed, the Zeus2 will update any WIFI-1 units on the Ethernet network. Follow the onscreen directions. Power cycle the WIFi-1 module after the upgrade.
Ethernet network stability
Radar: Improvements to Ethernet network connectivity to avoid the “No Radar” message sometimes encountered using 3G or 4G Radars.
ForwardScan: Resolved an issue where in some circumstances ForwardScan would show “No Source” message. Note: If ForwardScan transducer is connected to a SonarHub. The SonarHub module will require an update. Download the file Sonar_Hub-3.0-52.1.103-32282-r1-Standard-1.riw at bandg.com.
Power control setting
The default (Factory Reset) setting for Power Control has now changed from Slave to Master. The setting change will apply to new factory units or when a v3.0 unit has been reset to factory defaults.
Change in update procedure
There is a slight change to the behavior of the update process. Once this update has been applied:
The display will restart and will now bypass the “Update selection” menu
Zeus2 MFD: On some displays the unit will then perform a touch calibration. This will have a prompt not to touch the screen. This will take a few seconds and reboot afterwards. This step only happens during this update.
Page 4 of 4
Known Issues Listed below are a number of issues we are aware of but were not fixed in time for this release. We are working hard to resolve these issues for the next release of software later in the year.
Import of large user data files can cause a lowering of performance
Persistent Jeppesen message appearing on start-up if C-MAP chart card is used
New B&G ZC1 Software Version 1.4.0 Product: ZC1 Controller
Product Description: 000-11097-001
Software Version: ZC1 1_4_00_00.swup
Effective Date: August 2015
Inspect/Update Current Inventory: Yes
B&G is pleased to announce a software upgrade for the ZC1 Wired Controller. The new version 1.4.0.00 will supersede all previous versions. Version 1.4.0.00 has changes that can improve the stability of NMEA 2000/SimNet networks especially large networks. The power consumption of the ZC1 has been considerably reduced from 5 LEN (240 mA) down to 2 LEN (85 mA). The ZC1 software version can be checked in the Network Device List. Click on the ZC1 display and view the Device Information. The new version should show “Software Ver. 1.4.0.00”. The new software is available from the bandg.com website. Upgrades can be performed via a B&G multi-function display or using the ST10 and SWUP program. Note: Apply the upgrade to one ZC1 unit at a time.
For More Information: U.S. Based Resellers Technical and Order Support: (800) 324-4737
Canada Based Resellers Technical Support: (855) 361-1564
You may also send any inquiries via email to the addresses listed below, according to your sales-group classification:
B&G is pleased to announce that new software has been released for the ZM range of widescreen monitors. This release incorporates some important improvements.
The software upgrade is comprised of two upgrade files.
One is for the BIOS or MCU (main control unit).
The other is a FSU (Full System Update) which contains all three software components to update the Boot Loader, MCU and OSD (On Screen Display)"
The two files MUST be installed in sequential order.
First: ZM16 19 - MCU 1_4_02_00.swup
Second: ZM16 19 - FSU 1_0_03_00.swup
The two files will be rolled into one .Zip file called ZM16_19_FSU_1_0_03_00.zip. The software can be downloads page on the B&G website www.bandg.com
Improvements Touch control
Improvements have been made to the serial touch control to address reported issues of low sensitivity, intermittent touch, touch not working at startup, or taking a long time to become active.
Alarm
Resolves an issue where the monitors alarm buzzer continues to sound after the Zeus2 GH processor has been powered off.
Brightness control
This software will resolve backlight dimming issues experienced by some users.
Before commencing with the upgrade it is recommended that network traffic is minimized by de-powering unnecessary devices such as AIS transponders, and multifunction displays.
Upgrades must be performed dock side and not whilst the vessel is underway. Some NMEA 2000 devices will go into maintenance mode during the upgrade and will be off line.
Make sure all monitors to be upgrades are connected to the NMEA 2000 network.
Download the zipped software package from the B&G website
Unzip the two files to the root of a media card (SD card for Zeus2 GH, micro SD for Zeus2)
The Updaters can be run from any B&G MFD that is on the same NMEA 2000 network as the ZM Monitor. If there is another MFD other than a Zeus2 GH it is recommended to run the updater from that MFD.
How to check current versions
Before upgrading please make a note of the current versions of the monitor.
1. Press the power button on the monitor to bring up the OSD (On Screen Display) 2. Press down arrow to select CONFIGURATION 3. The software versions in the example below are
a. OSD 1.8.2 b. BIOS 1.3.3
Page 3 of 5
DO THIS FIRST!
First run the BIOS updater file “ZM16 19 - MCU 1_4_02_00.swup”
Only apply this upgrade to one monitor at a time. (Multiple monitors on a network can be powered on but only one monitor at a time should be selected for upgrade).
1. Insert the media card into the card reader of an MFD or Zeus2 GH processor. 2. From the HOME page select FILES. 3. Select the media card that holds the upgrade files. 4. Select the upgrade file “ZM16 19 - MCU 1_4_02_00.swup”.
5. Select UPGRADE to continue.
6. Select the monitor to upgrade (make sure only one is selected). Then select Start upgrade (OP40 press MENU> then select start upgrade).
7. The Upgrade process of the BIOS only takes a short time indicated by a process bar.
8. Once complete acknowledge upgrade successful message.
Page 4 of 5
9. The LED on the monitor will continue to flash for approximately 45 seconds after which the monitor (not the Zeus2 GH) will automatically restart.
10. Press X to exit installer page. 11. Apply to the next monitor.
Second run the FSU updater file “ZM16 19 - FSU 1_0_03_00.swup”
Make sure you have upgraded the BIOS (MCU 1.4.2 or later) as above.
This Upgrade can be applied to multiple monitors on the network at the same time (up to six monitors).
1. Insert the media card in to the card reader of an MFD or Zeus2 GH processor. 2. From the HOME page select FILES. 3. Select the media card that holds the upgrade files. 4. Select the upgrade file “ZM16 19 - FSU 1_0_03_00.swup”. 5. Select UPGRADE to continue. 6. Select the monitor(s) to upgrade (you can select up to six monitors at a time). Then select Start
upgrade.
7. This process will take about twenty minutes to upgrade one monitor. Allow for an extra ten minutes for each additional monitor that is selected to be upgraded. Please be patient. It is important not to remove power to the system at this stage.
8. As each monitor is upgrading the red LED status light will flash. 9. Once complete acknowledge upgrade successful message. 10. The LED on the monitor will continue to flash for approximately 45 seconds after which the
monitor (not the Zeus2 GH) will automatically restart. 11. Press X to exit installer page.
Page 5 of 5
Recheck the software versions
After applying both upgrades. Recheck the version numbers.
1. Press the power button on the monitor to bring up the OSD (On Screen Display). 2. Press down arrow to select CONFIGURATION. 3. The new software versions displayed should be
a. OSD Should now be 1.9.2 b. The BIOS should now be 1.4.2
For More Information: U.S. Based Resellers Technical and Order Support: (800) 324-4737
Canada Based Resellers Technical Support: (855) 361-1564
You may also send any inquiries via email to the addresses listed below, according to your sales-group classification:
