Installaon guide Alpina B3 BITURBO 301 kW 410 PS Date: 03.03.2014 page:1 The product described in the guidance was developed, manufactured and controlled consi- dering the necessary safety reguirements. The product must be installed properly to ensure a proper funcon and avoid danger for persons and things. Please read this installaonguide inclusive safety instrucons carefully. Scope of supply: Quanty arcle 1x Tuningbox 1x loom 1x Bridge plug 1x Fastening kit 1. Open the hood. 2.Turn the ignion off! 3.Remove the ignionkey! 4.Close and lock all doors! 5.Do not open any doors while installing the tuningkit! 6.Wait 5 minutes before beginning the installaon In order to avoid damages at electronic vehicle compo- nents, you have to be sure that you have done all neces- sary methods for electostac discharge . Install the electronic in an waterproof and vibraonless place. Do not make any changes at the tuning-kit! Do not expand or shorten the loom.
Transcript
Installation guide
Alpina B3 BITURBO
301 kW 410 PS
Date: 03.03.2014 page:1
The product described in the guidance was developed, manufactured and controlled consi-
dering the necessary safety reguirements.
The product must be installed properly to ensure a proper function and avoid danger for
persons and things.
Please read this installationguide inclusive safety instructions carefully.
Scope of supply:
Quantity article
1x Tuningbox
1x loom
1x Bridge plug
1x Fastening kit
1. Open the hood.
2.Turn the ignition off!
3.Remove the ignitionkey!
4.Close and lock all doors!
5.Do not open any doors while installing the tuningkit!
6.Wait 5 minutes before beginning the installation
In order to avoid damages at electronic vehicle compo-
nents, you have to be sure that you have done all neces-
sary methods for electostatic discharge .
Install the electronic in an waterproof and vibrationless
place. Do not make any changes at the tuning-kit!
Do not expand or shorten the loom.
Installation guide
Alpina B3 BITURBO
301 kW 410 PS
Date: 03.03.2014 page:2
Overview:
The tuningkit has to be attached to the following points:
Manifold air pressure
Boost pressure sensor (under the air filter box)
Camshaft sensor
Required tools:
Cutter, Screwdriver
Vorbereitung:
Move the individual strands of the loom to the associated plug connectors
Put the required tools by your side ( if needed )
Take the fastening material at your side
To get the maximum power enhancement , you have to use „super plus“ (98 ROZ)
![Silva&Machado POS[2019] vfinal · 2019-12-07 · ñ l î õ l î ì í õ í î ñ X í X } } v v ( ( ] n & } ì í ì ì î ì ì ï ì ì ð ì ì ñ ò ó ô õ ì í î ï ð](https://static.documents.pub/doc/80x56/5fa45f5e732e8d7fe740e652/silvamachado-pos2019-vfinal-2019-12-07-l-l-.jpg)
![^ /D^ D v µ o D X/D^ X ì ì ì ì í r ì í í · D X/D^ X ì ì ì ì í r ì í í E u s o ] ] } v W Ç W o o ] } v < ZZ s o ] î ñ l ì ð l î ì í õ s ] ( ] Ç W v v ]](https://static.documents.pub/doc/80x56/5e6b120b2868a730a95c7c3b/-d-d-v-o-d-xd-x-r-d-xd-x-r-.jpg)
![lEDdD l&DDd & D d ] }D } o } D ] ] v d ] } î ì í õ î ì í ... · / lEDdD l&DDd & D d ] }D } o } D ] ] v d ] } î ì í õ î ì í ô î ì í ó î ì í ò î ì í ñ î](https://static.documents.pub/doc/80x56/5f01b4ff7e708231d400a733/leddd-lddd-d-d-d-o-d-v-d-leddd.jpg)