1 9 CA R R I N G TO N ST R E E T ( C N R H I N C KS M A N ST )P O B OX 6 0 0 8 | Q U E A N B E YA N N S W 2 6 2 0PH : ( 0 2 ) 6 2 9 9 5 8 1 7 FAX : ( 0 2 ) 6 2 9 9 5 8 6 3E M A I L : s a l e s @ a l u f o r m i n te r i o r s . c o m . a uwww. a l u f o r m i n te r i o r s . c o m . a u
A L U - V E N T D O O R G R I L L E S
With a single set of angled f ixed blades on both sides, Aluform’s Alu-Vent door grilles provide easy relief for air flow and
air conditioning whilst guaranteeing occupant privacy. Supplied as a fully assembled unit, these vents can be easily
snapped together for quick installation and come with a complete telescopic back f rame for an aesthetic appearance
on both sides of the door, maintaining the maximum f ree area and keeping noise to a minimum.
D E S C R I PT I O N
+ Suits door thicknesses f rom 30 - 45mm
+ Easy installation on site
+ Available in natural anodised and powdercoated f inishes (lead time of 5 working days applies to powdercoated vents)
+ Stocked in a natural anodised f inish and are available in a range of standard sizes:
V3015 - 300 x 150mm cut out size
V4515 - 450 x 150mm cut out size
V6015 - 600 x 150mm cut out size
V6020 - 600 x 200mm cut out size
V6025 - 600 x 250mm cut out size
V6030 - 600 x 300mm cut out size
V6045 - 600 x 450mm cut out size
V6060 - 600 x 600mm cut out size
+ For custom size door vents, send us message at [email protected] or call us at 1800 995 817
(lead time of 10 working days applies to custom size vents)
F E ATU R E S
1 9 CA R R I N G TO N ST R E E T ( C N R H I N C KS M A N ST )P O B OX 6 0 0 8 | Q U E A N B E YA N N S W 2 6 2 0PH : ( 0 2 ) 6 2 9 9 5 8 1 7 FAX : ( 0 2 ) 6 2 9 9 5 8 6 3E M A I L : s a l e s @ a l u f o r m i n te r i o r s . c o m . a uwww. a l u f o r m i n te r i o r s . c o m . a u
I N STA L L AT I O N I N ST R U C T I O N S
Aluminium Door Vent
Step 1 Step 2 Step 3 Step 4
Insert clip so that middle tab fits into upper groove and one side tab fits into lower groove.
Pry second side tab into lowergroove using screw driver.
Ensure clip is installed correctly and repeat for all clips provided. Space clips proportionally on all four sides.
Place front frame into opening and press back frame into position from opposite side of the door, ensuring clips catch as shown.
Silicon seal to inside of flange will prevent movement within opening after installation. Removal of Vent after installation may result in damage to the clips and possibly the frame.
Note
Vent Flow Installation Instructions
Vent Flow Specifications
3 Criterion Industries
Aluminium Door Vent
Step 1 Step 2 Step 3 Step 4
Insert clip so that middle tab fits into upper groove and one side tab fits into lower groove.
Pry second side tab into lowergroove using screw driver.
Ensure clip is installed correctly and repeat for all clips provided. Space clips proportionally on all four sides.
Place front frame into opening and press back frame into position from opposite side of the door, ensuring clips catch as shown.
Silicon seal to inside of flange will prevent movement within opening after installation. Removal of Vent after installation may result in damage to the clips and possibly the frame.
Note
Vent Flow Installation Instructions
Vent Flow Specifications
3 Criterion Industries
N OT E
Using silicon to seal the inside of flange will prevent movement within operating after installation.
Removing the Alu-Vent Door Grille after installation may result in damage to the clips and possibly the f rame.