AM 203 CV AM 243 CV / + B AM 283 CV / +B...Original operating instructions Disc Mower AM 203 CV AM...

Ori

gin

al

op

era

tin

g i

ns

tru

cti

on

s

Disc Mower

AM 203 CV AM 243 CV / + B AM 283 CV / +B

(from serial no.: 829 190)

Order no.: 150 000 003 01 en

15.06.2015

Table of Contents

2

Pos: 1 /BA/Konformitätserklärungen/Mähwerke AM Baureihe/AM-CV-Baureihe @ 72\mod_1307362438629_78.docx @ 647293 @ @ 1 CV0

EC Declaration of Conformity

We, Maschinenfabrik Bernard Krone GmbH Heinrich-Krone-Str. 10, D-48480 Spelle

hereby declare as manufacturer of the product named below, on our sole responsibility,

that the

Machine: Krone disc mower Type / Types: AM 203 CV; AM 243 CV; AM 243 CV + B; AM 283 CV;

AM 283 CV + B to which this declaration refers is in compliance with the relevant provisions of

EC Directive 2006/42/EC (Machinery) The signing Managing Director is authorised to compile the technical documents. Spelle, 20.04.10

Dr.-Ing. Josef Horstmann (Managing Director, Design and Development)

Year of manufacture: Machine No.:

Pos: 2 /BA/Vorwort/Sehr geehrter Kunde @ 0\mod_1195626300326_78.docx @ 905 @ @ 1

Dear customer, Dear customer,

You have now received the operating instructions for the KRONE product which you have purchased.

These operating instructions contain important information for the proper use and safe operation of the machine.

If these operating instructions should become wholly or partially unusable, you can obtain replacement operating instructions for your machine by stating the number given overleaf. Pos: 3 /Layout Module /---------------Seitenumbruch---------------- @ 0\mod_1196175311226_0.docx @ 4165 @ @ 1

Table of Contents

3

Pos: 4 /Überschriften/Überschriften 1/F-J/Inhaltsverzeichnis @ 31\mod_1251969952727_78.docx @ 302165 @ 1 @ 1

1 Table of Contents Pos: 5 /BA/Inhaltsverzeichnis Sprachenneutral @ 10\mod_1221574899104_0.docx @ 135495 @ @ 1

1 Table of Contents ................................................................................................................................... 3

2 Foreword ................................................................................................................................................. 6

3 Introduction ............................................................................................................................................. 7

3.1 Purpose of Use ................................................................................................................................... 7

3.2 Validity ................................................................................................................................................ 7

3.2.1 Contact ........................................................................................................................................ 7

3.3 Identification Plate .............................................................................................................................. 8

3.4 Information Required for Questions and Orders ................................................................................ 8

3.5 Intended Use ...................................................................................................................................... 9

3.6 Service life of the machine ................................................................................................................. 9

3.7 Technical data .................................................................................................................................. 10

4 Safety ..................................................................................................................................................... 11

4.1 Identifying Symbols in the Operating Instructions ............................................................................ 11

4.2 Identification of the hazard warnings ................................................................................................ 11

4.2.1 Personnel Qualification and Training ........................................................................................ 12

4.2.2 Dangers in Case of Non-compliance with the Safety Instructions ............................................ 12

4.2.3 Safety-conscious work practices ............................................................................................... 12

4.3 Safety Instructions and Accident Prevention Regulations ............................................................... 13

4.4 Attached devices .............................................................................................................................. 14

4.5 PTO operation .................................................................................................................................. 15

4.6 Hydraulic system .............................................................................................................................. 16

4.7 Maintenance ..................................................................................................................................... 16

4.8 Unauthorised Conversion/Modification and Spare Parts Production ............................................... 16

4.9 Inadmissible Modes of Operation ..................................................................................................... 16

4.10 Working in the vicinity of power transmission lines .......................................................................... 17

4.11 Introduction ....................................................................................................................................... 19

4.12 Position of the Adhesive Safety Stickers on the Machine ................................................................ 20

4.13 Position of the General Information Labels on the Machine ............................................................ 22

4.13.1 Re-Ordering the Adhesive Safety and Information Labels ....................................................... 23

4.13.2 Affixing the Adhesive Safety and Information Labels ............................................................... 23

5 Commissioning..................................................................................................................................... 24

5.1 First installation ................................................................................................................................ 24

5.2 Special Safety Instructions ............................................................................................................... 24

5.3 Mounting onto the Tractor ................................................................................................................ 25

5.3.1 Clutching points ......................................................................................................................... 25

5.3.2 Attaching the Three-Point Block ............................................................................................... 26

5.4 PTO shaft ......................................................................................................................................... 27

5.4.1 Length adjustment..................................................................................................................... 27

5.5 Adjustment Piece for Lifting Cylinder and Compensation Spring .................................................... 28

6 Start-up .................................................................................................................................................. 30

6.1 Mounting onto the Tractor ................................................................................................................ 30

6.2 Hydraulics ......................................................................................................................................... 31

6.2.1 Special Safety Instructions ........................................................................................................ 31

6.2.2 Connecting the hydraulic lines .................................................................................................. 31

6.3 PTO shaft ......................................................................................................................................... 33

6.4 Install the PTO shaft ......................................................................................................................... 33

Table of Contents

4

6.5 Intermediate PTO shaft .................................................................................................................... 34

6.6 Parking support ................................................................................................................................ 34

6.7 Fastening the Compensation Spring ................................................................................................ 35

7 Driving and Transport .......................................................................................................................... 36

7.1 Switching from working position to transport position ...................................................................... 36

7.2 Lighting ............................................................................................................................................. 37

8 Operation ............................................................................................................................................... 38

8.1 From transport into working position ................................................................................................ 38

8.2 Before mowing ................................................................................................................................. 39

8.2.1 Folding down the Safety Device ............................................................................................... 39

8.3 Using the Machine for Work ............................................................................................................. 40

8.4 Headland Position ............................................................................................................................ 40

8.5 Detaching the machine .................................................................................................................... 41

9 Settings ................................................................................................................................................. 44

9.1 Setting of the top suspension arm connecting point ........................................................................ 44

9.2 Adjusting the cutting height .............................................................................................................. 44

9.3 Adjusting the Compensation Springs ............................................................................................... 45

9.4 Setting of the pole protection mechanism ........................................................................................ 46

9.5 Default Setting of the Tractor's Lower Suspension Arms ................................................................ 47

9.6 Adjusting the Tedder Speed ............................................................................................................. 48

9.7 Adjusting the conditioner plate ......................................................................................................... 49

9.8 Adjusting the Swath Width ............................................................................................................... 49

9.9 Setting of the tine conditioner ........................................................................................................... 50

9.9.1 Deactivating the tine conditioner ............................................................................................... 51

9.10 Wide Swath Cover............................................................................................................................ 52

9.10.1 Making Adjustments for Swathing ............................................................................................. 53

10 Maintenance .......................................................................................................................................... 54


10.1.1 Test run ..................................................................................................................................... 54

10.2 Spare Parts ...................................................................................................................................... 54

10.3 Tightening torques ............................................................................................................................ 55

10.3.1 Metric Thread Screws with Control Thread .............................................................................. 55

10.3.2 Metric Thread Screws with Fine Thread ................................................................................... 56

10.3.3 Metric Thread Screws with Countersunk Head and Hexagonal Socket ................................... 56

10.3.4 Deviating Torque ....................................................................................................................... 57

10.4 Filling Quantities and Lubrication Designations for Gearboxes ....................................................... 58

10.4.1 Oil Level Check and Oil Change Intervals (Gearboxes) ........................................................... 58

10.5 Main gearbox .................................................................................................................................... 59

10.6 Speed gearbox ................................................................................................................................. 60

10.7 Oil level check and oil change on the cutter bar .............................................................................. 61

10.7.1 Oil change ................................................................................................................................. 61

10.7.2 Checking the oil level ................................................................................................................ 61

10.8 Guard Cloths .................................................................................................................................... 62

10.9 Tedder .............................................................................................................................................. 63

10.10 Maintenance of pole protection ........................................................................................................ 63

10.11 Checking the Cutter Blades and Blade Holder ................................................................................ 64

10.11.1 Cutter Blades ............................................................................................................................ 65

10.11.2 Blade Screw Connection ........................................................................................................... 66

Table of Contents

5

10.11.3 Blade Quick-Fit Device ............................................................................................................. 66

10.12 Blade Changing on Cutting Discs .................................................................................................... 67

10.13 Special Tool ...................................................................................................................................... 67

10.13.1 Blade Screw Connection ........................................................................................................... 68

10.13.2 Blade Quick-Fit Device ............................................................................................................. 69

10.14 Replacing the Linings ....................................................................................................................... 70

11 Maintenance – lubrication chart ......................................................................................................... 71


11.2 PTO shaft ......................................................................................................................................... 71

11.3 Lubrication Chart .............................................................................................................................. 72

12 Placing in Storage ................................................................................................................................ 73

13 Before the Start of the New Season ................................................................................................... 74


13.2 Test run. ........................................................................................................................................... 74

13.3 Friction Clutch .................................................................................................................................. 76

13.4 Walterscheid Overload Coupling ...................................................................................................... 76

13.4.1 Venting the Overload Coupling on the Drive Shaft to the Cutter Bar ....................................... 77

14 Special equipment ................................................................................................................................ 78


14.2 Adjusting Skids ................................................................................................................................. 78

15 Appendix - Assembly Instructions ..................................................................................................... 79

16 Disposal of the machine ...................................................................................................................... 90

16.1 Disposal of the machine ................................................................................................................... 90

Pos: 6 /Layout Module /---------------Seitenumbruch---------------- @ 0\mod_1196175311226_0.docx @ 4165 @ @ 1

Foreword

6

Pos: 7.1 /Überschriften/Überschriften 1/U-Z/Vorwort @ 0\mod_1195627720123_78.docx @ 982 @ 1 @ 1

2 Foreword Pos: 7.2 /BA/Vorwort/EasyCut/Verehrter Kunde EasyCut @ 3\mod_1204546394934_78.docx @ 70529 @ @ 1

Dear Customer! By purchasing the disc mower, you have acquired a quality product made by KRONE. We are grateful for the confidence you have invested in us in buying this machine. To be able to use the disc mower optimally, please read these operating instructions thoroughly before you start using the machine. The contents of this manual are laid out in such a way that you should be able to perform any task by following the instructions step by step. It contains extensive notes and information about maintenance, how to use the machine safely, secure working methods, special precautionary measures and available accessories. This information and these instructions are essential, important and useful for the operational safety, reliability and durability of the disc mower.

Pos: 7.3 /BA/Vorwort/EasyCut/Weiterer Verlauf EasyCut @ 3\mod_1204546850246_78.docx @ 70549 @ @ 1

Note In the operating instructions which follow, the disc mower will also be referred to as the "machine".

Pos: 7.4 /BA/Vorwort/Beachten Sie für Maschine @ 0\mod_1195626904076_78.docx @ 944 @ @ 1

Please note: The operating instructions are part of your machine. Only operate this machine after you have been trained to do so and according to these instructions. It is essential to observe the safety instructions! It is also necessary to observe the relevant accident prevention regulations and other generally recognised regulations concerning safety, occupational health and road traffic. All information, illustrations and technical data in these operating instructions correspond to the latest state at the time of publication. We reserve the right to make design changes at any time and without notification of reasons. Should you for any reason not be able to use these operating instructions either wholly or partially, you can receive a replacement set of operating instructions for your machine by quoting the number supplied overleaf. We hope that you will be satisfied with your KRONE machine. Maschinenfabrik Bernard Krone GmbH Spelle


Introduction

7

Pos: 9.1 /BA/Einleitung/Einleitung @ 0\mod_1195562498677_78.docx @ 416 @ 1 @ 1

3 Introduction

These operating instructions contain fundamental instructions. These must be observed in operation and maintenance. For this reason, these operating instructions must be read by operating personnel before commissioning and use, and must be available for easy reference. Follow both the general safety instructions contained in the section on safety and the specific safety instructions contained in the other sections.

Pos: 9.2 /Überschriften/Überschriften 2/U-Z/VVerwendungszweck @ 1\mod_1201707246738_78.docx @ 54055 @ 2 @ 1

3.1 Purpose of Use Pos: 9.3 /BA/Einleitung/Mähwerke AM Baureihe/Verwendungszweck AM-Baureihe @ 69\mod_1305029359144_78.docx @ 630919 @ @ 1

The disc mower is used for cutting crops growing on the ground. Pos: 9.4 /BA/Einleitung/Mähwerke AM Baureihe/Gültigkeit AM 203 CV / 243 CV / 283 CV @ 72\mod_1307448941646_78.docx @ 650656 @ 2 @ 1

3.2 Validity

These operating instructions apply to disc mowers of series: AM 203 CV; AM 243 CV; AM 243 CV + B; AM 283 CV and AM 283 CV + B

Pos: 9.5 /Überschriften/Überschriften 3/A-E/A/Ansprechpartner @ 0\mod_1195569394286_78.docx @ 839 @ 3 @ 1

3.2.1 Contact Pos: 9.6 /BA/Adressen/Adresse Maschinenfabrik KRONE Spelle @ 0\mod_1195568531083_78.docx @ 734 @ @ 1

Maschinenfabrik Bernard Krone GmbH Heinrich-Krone-Strasse 10 D-48480 Spelle (Germany) Telephone: + 49 (0) 59 77/935-0 (Head Office) Fax.: + 49 (0) 59 77/935-339 (Head Office) Fax.: + 49 (0) 59 77/935-239 (Spare parts - domestic) Fax.: + 49 (0) 59 77/935-359 (Spare parts - export) Email: [email protected]

Pos: 9.7 /Layout Module /---------------Seitenumbruch---------------- @ 0\mod_1196175311226_0.docx @ 4165 @ @ 1

Introduction

8

Pos: 9.8 /Überschriften/Überschriften 2/K-O/KKennzeichnung @ 0\mod_1195564622099_78.docx @ 496 @ 2 @ 1

3.3 Identification Plate Pos: 9.9 /BA/Einleitung/Kennzeichnung/AM-Mähwerke/Kennzeichnung AM 203 CV / 243 CV / 283 CV @ 72\mod_1307449162690_78.docx @ 650684 @ @ 1

Maschinenfabrik Bernard Krone GmbHHeinrich-Krone-Straße 10, D 48480 Spelle

JahrAnnée

Masch. NrNo. de série

TypeMade in

W.-Germany

AM-1-106

Fig. 1 The machine data are rendered on the type plate (1). It is attached to the carrying bar.

Pos: 9.10 /BA/Einleitung/Kennzeichnung/Angaben für Anfrage und Bestellungen_Maschnr. @ 9\mod_1220507505930_78.docx @ 126110 @ 2 @ 1

3.4 Information Required for Questions and Orders

Year

Mach. No.

Type

Note The entire identification plate represents a legal document and should not be altered or rendered illegible! When asking questions concerning the machine or ordering spare parts, be sure to provide type designation, machine number and the year of manufacture of the relevant machine: To ensure that these data are always available, we recommend that you enter them in the fields above.

Note Authentic KRONE spare parts and accessories authorised by the manufacturer help to ensure safety. The use of spare parts, accessories or additional equipment not manufactured, tested or approved by KRONE will exclude any liability for consequential damage.


Introduction

9

Pos: 9.12.1 /Überschriften/Überschriften 2/A-E/BBestimmungsgemäßer Gebrauch (alt) @ 0\mod_1196401545090_78.docx @ 7728 @ 2 @ 1

3.5 Intended Use Pos: 9.12.2 /BA/Einleitung/Bestimmungsgemäßer Gebrauch/EasyCut/Bestimmungsgemäßer Gebrauch (Einzahl) @ 3\mod_1204548357809_78.docx @ 70671 @ @ 1

The disc mower is built exclusively for customary use in agricultural work (intended use). Pos: 9.12.3 /BA/Einleitung/Bestimmungsgemäßer Gebrauch/Nicht bestimmungs gemäss (2012-03-19 16:41:15) @ 0\mod_1196401324340_78.docx @ 7690 @ @ 1

Any use of the machine for other purposes is deemed not to be in accordance with intended use. The manufacturer shall not be liable for any resulting damage; the user alone shall bear the risk. Operation in accordance with intended use also includes observing the operating, maintenance and service instructions specified by the manufacturer. Unauthorised modifications to the machine may affect the properties of the machine or disrupt proper operation. For this reason, unauthorised modifications shall exclude any liability of the manufacturer for consequential damage.

Pos: 9.13 /Überschriften/Überschriften 2/K-O/NNutzungsdauer der Maschine @ 318\mod_1423658430909_78.docx @ 2465744 @ 2 @ 1

3.6 Service life of the machine Pos: 9.14 /BA/Einleitung/Nutzungsdauer der Maschine_Text @ 318\mod_1423556613022_78.docx @ 2463145 @ @ 1

– The service life of this machine strongly depends on proper use and maintenance as well as the operating conditions.

– Permanent operational readiness as well as long service life of the machine can be achieved by observing the instructions and notes of these operating instructions.

– After each season of use, the machine must be checked thoroughly for wear and other damage.

– Damaged and worn parts must be replaced before placing the machine into service again. – After the machine has been used for five years, carry out full technical inspection of the

machine. According to the results of this inspection, a decision concerning the possibility of reuse of the machine should be taken.

– Theoretically, the service life of this machine is unlimited as all worn or damaged parts can be replaced.


Introduction

10

Pos: 9.16 /BA/Einleitung/Technische Daten/Technische Daten mit 2. Überschrift @ 0\mod_1195566374865_78.docx @ 594 @ 2 @ 1

3.7 Technical data

All information, illustrations and technical data in these operating instructions correspond to the latest state at the time of publication. We reserve the right to make design changes at any time and without notification of reasons.

Pos: 9.17 /BA/Einleitung/Technische Daten/AM-Mähwerke/AM 203 CV / 243 CV / 283 CV @ 72\mod_1307449756380_78.docx @ 650743 @ @ 1 wa

Type AM 203 CV AM 243 CV (AM 243 CV +B)

AM 283 CV (AM 283 CV +V)

Working width [mm] 2000 2400 2800

Transport width [mm] Tractor width

Number of mowing discs 3 4 5

Number of mowing drums 2 2 2

Conditioner system V-shaped prong

Speed of V-tine rotor [rpm] 600 and 900

Width of conditioner system [mm] 1600 2000 2400

Swath width [m] 0.8 – 1.6 0.9 -2 (0.9 – 2.3)

1.2 – 2.4 (1.2 – 2.7)

Acreage [ha/h] 2.5 3 3.5

Power consumption [kW/HP]

33/45 37/50 44/60

PTO speed [rpm] 540

Hydraulic connections required

1 x EW*

Service weight [kg] approx. 760

approx. 810 approx. 860

*) EW= Single-action control unit


Safety

11

Pos: 11.1 /Überschriften/Überschriften 1/P-T/Sicherheit @ 0\mod_1195566748646_78.docx @ 635 @ 1 @ 1

4 Safety Pos: 11.2 /BA/Sicherheit/6. Überarbeitete Warnhinweise/Kennzeichnung von Hinweisen in der Betriebsanleitung Einführungstext (2012-07-27 09:59:06) @ 0\mod_1195637804826_78.docx @ 1098 @ 2 @ 1

4.1 Identifying Symbols in the Operating Instructions

The safety instructions contained in this manual which could result in personal injury if not followed are identified by the general danger sign:

Pos: 11.3 /BA/Sicherheit/6. Überarbeitete Warnhinweise/Kennzeichnung der Gefahrenhinweise (2012-07-26 15:10:30) @ 28\mod_1250244370070_78.docx @ 274714 @ 2 @ 1

4.2 Identification of the hazard warnings

Danger!

DANGER! - Type and source of the hazard! Effect: Danger to life or serious injuries. • Measures for hazard prevention Warning !

WARNING! - Type and source of the hazard! Effect: Injuries, serious material damage. • Measures for hazard prevention Caution!

CAUTION! - Type and source of the hazard! Effect: Property damage • Measures for risk prevention.

Pos: 11.4 /BA/Sicherheit/6. Überarbeitete Warnhinweise/Allgemeine Funktionshinweise (2012-07-26 15:24:39) @ 0\mod_1196869714452_78.docx @ 15185 @ @ 1

General function instructions are indicated as follows: Note!

Note - Type and source of the note Effect: Economic advantage of the machine • Actions to be taken

Instructions which are attached to the machine need to be followed and kept fully legible.


Safety

12

Pos: 11.6.1 /BA/Sicherheit/Personalqualifikation und -schulung @ 0\mod_1195639383185_78.docx @ 1136 @ 3 @ 1

4.2.1 Personnel Qualification and Training

The machine may be used, maintained and repaired only by persons who are familiar with it and have been instructed about the dangers connected with it. The operator must define areas of responsibility and monitoring of personnel. Should personnel lack the required knowledge, they must receive the required training and instruction. The operator must ensure that the contents of these operating instructions have been fully understood by personnel. Repair work not described in these operating instructions should only be performed by authorised service centres.

Pos: 11.6.2 /BA/Sicherheit/Gefahren bei Nichtbeachtung der Sicherheitshinweise @ 0\mod_1195639434013_78.docx @ 1155 @ 3 @ 1

4.2.2 Dangers in Case of Non-compliance with the Safety Instructions

Failure to follow the safety instructions could result in personal injury and environmental hazards as well as damage to the machine. If the safety instructions are not respected, this could result in the forfeiture of any claims for damages. Failure to follow the safety instructions could result, for example, in the following hazards:

• Endangering of persons due to not protected working areas. • Breakdown of important machine functions • Failure of prescribed methods for repair and maintenance • Endangering of persons due to mechanical and chemical effects • Damage to the environment due to leaking hydraulic oil

Pos: 11.6.3 /BA/Sicherheit/Sicherheitsbewusstes Arbeiten_Teil1 @ 0\mod_1195639792576_78.docx @ 1174 @ 3 @ 1

4.2.3 Safety-conscious work practices

Always observe the safety instructions set out in these operating instructions, all existing accident prevention rules and any internal work, operating and safety rules issued by the operator. The safety and accident prevention regulations of the responsible professional associations are binding. The safety instructions provided by the vehicle manufacturer should also be observed. Observe the applicable traffic laws when using public roads. Be prepared for emergencies. Keep the fire extinguisher and first aid box within reach. Keep emergency numbers for doctors and fire brigade close to the telephone.

Pos: 11.6.4 /Layout Module /---------------Seitenumbruch---------------- @ 0\mod_1196175311226_0.docx @ 4165 @ @ 1

Safety

13

Pos: 11.6.5 /BA/Sicherheit/Sicherheits- und Unfallverhütungs-Vorschriften Swadro_Ladewagen_EasyCut @ 73\mod_1308298589597_78.docx @ 655493 @ 2 @ 1

4.3 Safety Instructions and Accident Prevention Regulations

1 Please follow all generally applicable safety and accident prevention regulations in addition to the safety instructions contained in these operating instructions!

2 The attached warning and safety signs provide important information for safe operation. Pay attention to these for your own safety!

3 When using public roads, make sure to observe the applicable traffic regulations! 4 Make sure that you are familiar with all equipment and controls as well as with their

functions before you begin working with the machine. It is too late to learn this when you are using the machine for work!

5 The user should wear close fitting clothes. Avoid wearing loose or baggy clothing. 6 Keep the machine clean to prevent the danger of fire! 7 Before starting or moving the machine, make certain that nobody is in the vicinity of the

machine! (Watch for children!) Make sure that you have a clear view! 8 Carrying passengers during operation and transport on the working implement is not

permitted. 9 Couple implements correctly! Attach and secure implements to specified devices only! 10 When attaching or detaching implements, place the supporting devices in the correct

positions! 11 Use extreme caution when attaching or detaching implements onto or from the tractor! 12 Always attach ballast weights properly to the fixing points provided! 13 Observe permitted axle loads, gross weight and transport dimensions! 14 Check and attach transport equipment, such as lighting, warning devices and protective

equipment! 15 Actuating mechanisms (cables, chains, linkages etc.) for remote controlled devices must be

positioned in such a way that no movements are unintentionally triggered in any transport or working positions.

16 Ensure that implements are in the prescribed condition for on-road travel and lock them in place in accordance with the manufacturer's instructions!

17 Never leave the driver's seat when the vehicle is moving! 18 Always drive at the correct speed for the prevailing driving conditions! Avoid sudden

changes in direction when travelling uphill or downhill or across a gradient! 19 Hitched implements and ballast weights affect the driving, steering and braking response of

the machine. Make sure that you are able to brake and steer the machine as required! 20 Take into account the extension radius and/or inertia of an implement when turning corners! 21 Start up implements only when all safety devices have been attached and set in the

required position! 22 Keep safety equipment in good condition. Replace missing or damaged parts. 23 Keep clear of the working range of the machine at all times! 24 Do not stand within the turning and swivel range of the implement! 25 Never operate the hydraulic folding frames if anyone is inside the swivel range! 26 Parts operated by external power (e.g. hydraulically) can cause crushing and shearing

injuries! 27 Before leaving the tractor, lower the implement onto the ground, apply the parking brake,

switch off the engine and remove the ignition key! Pos: 11.6.6 /Layout Module /---------------Seitenumbruch---------------- @ 0\mod_1196175311226_0.docx @ 4165 @ @ 1

Safety

14

Pos: 11.6.7 /BA/Sicherheit/Angebaute Geräte/Geräte angebaut EasyCut @ 3\mod_1204552588996_78.docx @ 70752 @ 2 @ 1

4.4 Attached devices

1 Use extreme caution when attaching or detaching implements onto or from the tractor! 2 Couple the respective application devices to the appropriate couplings (e.g. three-point

suspension) only and secure them in a way (transport, use) that excludes inadvertent lifting or lowering of the device.

3 When using three-point linkage, the attachment categories of the tractor and the device (e.g. PTO speed, hydraulic system) must be coordinated!

4 When using the outside controls for the three-point linkage, do not step between the tractor and the device (risk of injury)!


Safety

15

Pos: 11.6.9 /BA/Sicherheit/Zapfwellenbetrieb Traktor @ 0\mod_1199699899350_78.docx @ 33264 @ 2 @ 1

4.5 PTO operation

1 Use only PTO shafts specified by the manufacturer! 2 The guard tube and guard cone of the PTO shaft and the PTO guard must be attached and

in good working condition (on the implement side, too)! 3 Make sure that the required tube covers are in place for PTO shafts in transport and

working position! 4 Before installing or detaching PTO shafts, disengage the PTO, switch off the engine and

remove the ignition key! 5 When using PTO shafts with an overload safety or free-running coupling which are not

shielded by the guard on the tractor, mount the overload safety or free-running coupling on the implement side!

6 Always make sure that the PTO shaft is properly installed and secured! 7 Attach chains to prevent the PTO shaft guard from rotating with the shaft! 8 Before switching on the PTO, make sure that the selected PTO speed of the tractor

matches the permissible implement speed! 9 Before switching on the PTO shaft make sure that no person is in the danger zone of the

device! 10 Never switch on the PTO if the engine is switched off! 11 No one should be in the vicinity of the rotating PTO or PTO shaft when the PTO is in use. 12 Always switch off the PTO shaft when the angle is too large or the PTO shaft is not

required! 13 Caution! After disengaging the PTO danger due to the flywheel running on! Keep away from

the implement during this time. The machine may be worked on only if it is completely at standstill and if the flywheel is secured by the parking brake.

14 Cleaning, lubricating or adjusting PTO driven implements or the PTO shaft only with PTO disengaged, engine switched off and ignition key withdrawn! Secure the fly-wheel with the parking brake.

15 Place the disconnected PTO shaft onto the support provided! 16 After detaching the PTO shaft, attach the protective cover to the PTO end! 17 If damage occurs, correct this immediately before using the implement!

Pos: 11.6.10 /BA/Sicherheit/Zapfwellenbetrieb Zusatz @ 2\mod_1203524761314_78.docx @ 66513 @ @ 1

Note The instructions of the manufacturer must be observed with regard to the PTO shaft. (separate operating instructions)


Safety

16

Pos: 11.6.12 /BA/Sicherheit/Hydraulikanlage @ 2\mod_1203503691986_78.docx @ 66225 @ 2 @ 1

4.6 Hydraulic system

1 The hydraulic system is pressurised! 2 When connecting hydraulic cylinders and motors, make sure the hydraulic hoses are

connected as specified! 3 When connecting the hydraulic hoses to the tractor hydraulics, make sure that the

hydraulics of both the tractor and the implement have been depressurized! 4 In the case of hydraulic connections between tractor and machine, the coupling sleeves and

plugs should be marked to ensure a proper connection! If the connectors are interchanged, the function will be reversed (e. g. raising/lowering) - Risk of accident!

5 When searching for leaks, use suitable aids to avoid the risk of injury! 6 Liquids escaping under high pressure (hydraulic oil) can penetrate the skin and cause

serious injury! Seek medical help immediately should injuries occur! Danger of infection! 7 Before working on the hydraulic system, depressurise the system and switch off the engine!

Pos: 11.6.13 /BA/Sicherheit/Hydraulikanlage Zusatz Alterung der Hydraulikschlauchleitungen @ 3\mod_1204552944856_78.docx @ 70772 @ @ 1

8 Check the hydraulic hose lines at regular intervals and replace them if damaged or worn! The new hoses must fulfill the technical requirements set by the manufacturer of the implement!

Pos: 11.6.14 /Überschriften/Überschriften 2/U-Z/WWartung @ 33\mod_1254222340957_78.docx @ 318599 @ 2 @ 1

4.7 Maintenance Pos: 11.6.15 /BA/Sicherheit/Wartung/Wartung Pos.1 ohne Schwungmass/Feststellbremse anziehen (2013-12-18 09:48:30) @ 17\mod_1236239576347_78.docx @ 203270 @ @ 1

1 Always make certain that the drive and the engine are switched off before doing any repairs, maintenance or cleaning! - Remove the ignition key!

Pos: 11.6.16 /BA/Sicherheit/Wartung/Wartung Pos.2 bis 8 ohne Elektronik @ 73\mod_1308295728779_78.docx @ 655465 @ @ 1

2 Regularly check that nuts and bolts are properly seated and tighten if necessary! 3 When performing maintenance work with the machine raised, always secure it with suitable

supporting elements! 4 Oils, greases and filters must be disposed of correctly! 5 If protective devices and guards are subject to wear, check them regularly and replace them

in good time! 6 Replacement parts must at least comply with the technical requirements set by the

manufacturer of the implements! This is guaranteed by original KRONE spare parts! Pos: 11.6.17 /BA/Sicherheit/Wartung/Wartung Zusatz Schneidwekzeuge @ 12\mod_1224578273531_78.docx @ 151591 @ @ 1

7 When replacing working tools with cutting edges, use suitable tools and gloves! Pos: 11.6.18 /BA/Sicherheit/Eigenmächtiger Umbau und Ersatzteilherstellung @ 1\mod_1201937705539_78.docx @ 55745 @ 2 @ 1

4.8 Unauthorised Conversion/Modification and Spare Parts Production

Conversions or modifications of the machine are permitted only with prior consultation with the manufacturer. Original spare parts and accessories authorised by the manufacturer help to ensure safety. Use of other parts may void liability for resulting damage.

Pos: 11.6.19 /BA/Sicherheit/Unzulässige Betriebsweisen @ 11\mod_1223357699923_78.docx @ 145527 @ 2 @ 1

4.9 Inadmissible Modes of Operation

The operating safety of the delivered machine is guaranteed only when it is used as intended in compliance with the introductory section "Intended use" of the operating instructions. The limit values listed in the data charts should not be exceeded under any circumstances.

Safety

17

Pos: 11.7 /BA/Sicherheit/Arbeiten im Bereich von Hochspannungsleitungen @ 11\mod_1223357468516_78.docx @ 145505 @ 2 @ 1

4.10 Working in the vicinity of power transmission lines

1 Always take great care when working under or in the vicinity of power transmission lines. 2 Ensure that when in operation or being transported, the machine cannot exceed a total

height of approx. 4m. 3 If there is any need to travel under overhead lines, the machine operator must request

information on the rated voltage and the minimum height of the overhead lines from the overhead line operator.

4 Always keep the safety distances according to the table.

Rated voltage kV

Safe distance from overhead lines m

To 1 1

Above 1 to 110 2

Above 101 to 220 3

Above 220 to 380 4


Safety

18

Pos: 11.9 /Layout Module /Diese Seite ist bewusst freigelassen worden. @ 1\mod_1201783680373_78.docx @ 54443 @ @ 1

This page has been left blank deliberately!! Pos: 11.10 /Layout Module /---------------Seitenumbruch---------------- @ 0\mod_1196175311226_0.docx @ 4165 @ @ 1

Safety

19

Pos: 11.11 /BA/Sicherheit/EasyCut/Sicherheit Einführung EasyCut @ 3\mod_1204553763950_78.docx @ 70812 @ 2 @ 1

4.11 Introduction

The disc mower is equipped with all safety devices (protective devices). However, it is not possible to eliminate all potential hazards on this machine as this would impair its full functional capability. Hazard warnings are attached to the machine in the relevant areas to warn against any dangers. The safety instructions are provided in the form of so-called warning pictograms. Important information on the position of these safety signs and what they mean is given below!

Pos: 11.12 /BA/Sicherheit/2. Vorangestellte Warnhinweise/Warnung - Beschädigte oder unlesbare Warnbildzeichen @ 120\mod_1343305789479_78.docx @ 1099853 @ @ 1

WARNING! Danger of injury on machine parts if danger zones have not been marked when warning pictograms are missing, damaged or illegible. Danger of injury due to dangerous parts and other residual risks as users or third parties enter the danger area or reach into it as they are not aware of the danger. • Immediately replace damaged or illegible labels. • Following repair work, always attach appropriate adhesive safety labels to all the replaced,

modified or repaired components. • Never clean areas carrying an adhesive safety label using a high-pressure cleaner. Familiarise yourself with the statement of the warning pictograms. The adjacent text and

the selected location on the machine provide information on the special danger spots on the machine.


Safety

20

Pos: 11.14 /Überschriften/Überschriften 2/K-O/LLage der Sicherheitsaufkleber an der Maschine @ 0\mod_1195634967326_78.docx @ 1020 @ 2 @ 1

4.12 Position of the Adhesive Safety Stickers on the Machine Pos: 11.15 /BA/Sicherheit/Aufkleber/AM Mähwerke/Sicherheitsaufkleber AM 203 CV / 243 CV / 283 CV @ 72\mod_1307451611517_78.docx @ 650827 @ @ 1

6

5 6

4 3

3 1 2

Fig. 2

Safety

21

1) Before starting the machine, read and observe the operating instructions and safety instructions. Order No. 939 471-1 (1x)

2) The PTO speeds must not exceed 540 rpm! The operating pressure of the hydraulic system must not exceed 200 bar!

939 100-4

MAX.540/min

MAX.200 bar Order No. 939 100-4 (1x)

3) While parts are moving, never reach into areas where there is a risk of being crushed. Order No. 942 196-1 (3x)

4) Move the protective devices into position prior to start-up. Order No. 939 572 0 (1x)

5) Do not touch any moving parts of the machine. Wait until they have come to a complete stop. Order No. 939 410 2 (1x)

6) When the machine is running, keep your distance. Order No. 942 197 1 (2x)


942 196 -1

939 410 2STOP

942 197-1

Safety

22

Pos: 11.17 /Überschriften/Überschriften 2/K-O/LLage der allgemeinen Hinweisaufkleber an der Maschine @ 0\mod_1195635067920_78.docx @ 1039 @ 2 @ 1

4.13 Position of the General Information Labels on the Machine Pos: 11.18 /BA/Sicherheit/Aufkleber/AM Mähwerke/Hinweisaufkleber AM 203 CV / 243 CV / 283 CV @ 72\mod_1307453129666_78.docx @ 650944 @ @ 1

4 5

7

28613

Fig. 3

1)

139 888-0 139 889-0

80

139-888 139-889

939 567 1 (1x)

2)

939 180 2 (1x)

3) D

F

GB

I

D

E

939 278 2 (1x)

4)

939 515 1 (1x) AM 203 CV 939 518 2 (1x) AM 243 CV 939 519 2 (1x) AM 283 CV

5)

939 511 1 (1x) AM 203 CV 939 512 2 (1x) AM 243 CV 939 513 2 (1x) AM 283 CV

6)

942 132 0 (1x)

Safety

23

7)

939 531-1 939 531 1 (1x)

8)

15 mm

min. 3mm

942 009 2 (1x) with blade screw connection

8)

18mm

12mm939 548 0

939 548 0 (1x) with blade screw connection

Pos: 11.19 /BA/Sicherheit/6. Überarbeitete Warnhinweise/Hinweis - Nachbestellung/ Anbringung Aufkleber @ 0\mod_1195637337107_78.docx @ 1079 @ 33 @ 1

4.13.1 Re-Ordering the Adhesive Safety and Information Labels

Note Every adhesive safety and information label is assigned an order number and can be ordered directly from the manufacturer or from an authorized dealer (see Section "Contact").

4.13.2 Affixing the Adhesive Safety and Information Labels

Note - Affixing an adhesive label Effect: Adhesion of the label • The surface for affixing the adhesive label must be clean and free of dirt, oil and grease.


Commissioning

24

Pos: 13.1 /Überschriften/Überschriften 1/A-E/Erstinbetriebnahme @ 0\mod_1196314201498_78.docx @ 5855 @ 1 @ 1

5 Commissioning Pos: 13.2 /Überschriften/Überschriften 2/A-E/EErstmontage @ 1\mod_1202226261982_78.docx @ 58270 @ 2 @ 1

5.1 First installation Pos: 13.3 /BA/Erstinbetriebnahme/Erstmontage wird im Anhang beschrieben @ 72\mod_1307454124462_78.docx @ 651000 @ @ 1

The appendix in this document "Appendix - Assembly Instructions" describes how to install the device for the first time.

Pos: 13.4 /Überschriften/Überschriften 2/P-T/SSpezielle Sicherheitshinweise @ 0\mod_1196660495760_78.docx @ 9134 @ 2 @ 1

5.2 Special Safety Instructions Pos: 13.5 /BA/Sicherheit/6. Überarbeitete Warnhinweise/Warnung- Einstellarbeiten Maschinen @ 297\mod_1412757509120_78.docx @ 2333197 @ @ 1

WARNING! When performing repair, maintenance or cleaning work on the machine, or in case of technical intervention, drive elements may start moving. Thus there is a risk of serious injuries or death. • Switch off tractor engine, remove the ignition key and carry it with you. • Secure the tractor against accidental start-up and against rolling. • Wait until all machine parts have come to a complete stop and have been cooled down

completely.

Pos: 13.6 /BA/Sicherheit/7. Gefahrenhinweise alt/Gefahr - Fehlerhafter Zusammenbau @ 1\mod_1202224212591_78.docx @ 58171 @ @ 1

Danger! - Incorrect assembly Effect: Danger to life, serious injuries or serious damage to the machine. • Only authorised service centres may assemble the machine. • The machine must be assembled with special care. • Always heed the applicable accident prevention regulations. • Use only safe and sufficiently dimensioned lifting equipment and load-securing equipment. • The machine may be taken into operation only after all the safety devices have been

installed. • If unauthorised modifications are made to the machine, the manufacturer is released from

liability for any resulting damage.

Pos: 13.7 /BA/Sicherheit/7. Gefahrenhinweise alt/Gefahr - Fehlende Schutztücher Erstinbetriebnahme @ 3\mod_1204628072251_78.docx @ 71025 @ @ 1

Danger! - Missing guard cloths Effect: Lebensgefahr, schwere Verletzungen oder schwere Schäden an der Maschine. • Before starting up the machine for the first time, install all supplied guard cloths on the

machine.


Commissioning

25

Pos: 13.9 /Überschriften/Überschriften 2/A-E/AAnbau an den Traktor @ 0\mod_1199717845194_78.docx @ 34039 @ 2 @ 1

5.3 Mounting onto the Tractor Pos: 13.10 /Überschriften/Überschriften 3/K-O/Kuppelpunkte @ 9\mod_1220531326398_78.docx @ 126608 @ 3 @ 1

5.3.1 Clutching points Pos: 13.11 /BA/Erstinbetriebnahme/Mähwerke AM Baureihe/Es gibt 2 Anbaumöglichkeiten @ 72\mod_1307454866088_78.docx @ 651086 @ @ 1

There are 2 ways to attach the mowing unit: Pos: 13.12 /BA/Erstinbetriebnahme/Mähwerke AM Baureihe/Kuppelpunkte Bild AM 203 CV / 243 CV / 283 CV @ 72\mod_1307454478072_78.docx @ 651030 @ @ 1

a c

Kat. II

AM-1-001

Kat. II

3

2

1

2

Fig. 4 Pos: 13.13 /BA/Erstinbetriebnahme/Mähwerke AM Baureihe/a) Kat. II Kuppelpunkte Text AM S und AM CV Baureihe @ 69\mod_1305036909040_78.docx @ 632644 @ @ 1

a) Cat. II The standard setting of the steerable pinions is for Cat. II.

Pos: 13.14 /BA/Erstinbetriebnahme/Mähwerke AM Baureihe/c) Kat. II seitlich versetzt AM S und AM CV Baureihe @ 69\mod_1305037661078_78.docx @ 632692 @ @ 1

c) Cat. II offset to the side To offset the mower to the side for Cat. II, turn the steerable pinion (3) 180° and shift the steerable pinion (1) outwards. • Remove the screws (2) • Insert the steerable pinion (3), rotated 180° • Offset the steerable pinion (1) outwards • Tighten the screws (2) again


Commissioning

26

Pos: 13.16 /Überschriften/Überschriften 3/A-E/D/Dreipunktbock anhängen @ 73\mod_1307685439395_78.docx @ 654872 @ 3 @ 1

5.3.2 Attaching the Three-Point Block Pos: 13.17 /BA/Sicherheit/6. Überarbeitete Warnhinweise/Warnung - Unbeabsichtigtes Abkuppeln angebaute @ 291\mod_1410427253866_78.docx @ 2294307 @ @ 1

Danger! - Inadvertent uncoupling of the machine during road travel or work. Effect: Danger to life, serious injuries or serious damage to the machine. • Use extreme caution when attaching or detaching devices to or from the tractor! The

accident prevention regulations must be complied with absolutely. • The lower suspension arms on the tractor must be fixed in position

with the retaining chains or bars to prevent the machine from swivelling out during transport or work. If the lower suspension arms (1) are equipped with catch hooks, the following items must be taken into consideration:

Especially in the headland position, high forces develop in the lower suspension arm bolts (3) that act upwards in the left-hand hook. For this reason, the catch hooks must be in a flawless condition. Additionally, the catch hooks must be secured in the provided locking hole (4) against unwanted opening after the machine has been connected to the tractor.

Pos: 13.18 /BA/Erstinbetriebnahme/Mähwerke AM Baureihe/Ankuppeln Bild AM 203 CV / 243 CV / 283 CV @ 72\mod_1307456041076_78.docx @ 651114 @ @ 1

1

AM-5-010

2

53 4

Fig. 5 Pos: 13.19 /BA/Erstinbetriebnahme/Mähwerke AM Baureihe/Ankuppeln Text AM 203 CV / 243 CV / 283 CV @ 72\mod_1307456211047_78.docx @ 651142 @ @ 1

• Attach the machine onto the lower suspension arm (1) of the tractor • Fasten the top suspension arm (2) onto the top suspension arm connecting point (5) and

secure it Pos: 13.20 /Layout Module /---------------Seitenumbruch---------------- @ 0\mod_1196175311226_0.docx @ 4165 @ @ 1

Commissioning

27

Pos: 13.21 /Überschriften/Überschriften 2/F-J/GGelenkwelle @ 0\mod_1199781879794_78.docx @ 34542 @ 2 @ 1

5.4 PTO shaft Pos: 13.22 /Überschriften/Überschriften 3/K-O/Längenanpassung @ 1\mod_1201687632810_78.docx @ 53589 @ 3 @ 1

5.4.1 Length adjustment Pos: 13.23 /BA/Erstinbetriebnahme/Mähwerke AM Baureihe/Längenanpassung Bild AM_CV Baureihe @ 72\mod_1307456462200_78.docx @ 651168 @ @ 1

AM-4-0541 2

Fig. 6 Pos: 13.24 /BA/Erstinbetriebnahme/Gelenkwelle/Mähwerke/Längenanpassung_ohne Pfahlsicherung @ 10\mod_1221813873039_78.docx @ 138060 @ @ 1

The length of the PTO shaft (1) must be adjusted. • Disassemble the PTO shaft. • Install each half (1) and (2) on the tractor and machine side respectively. • Check the special section tubes and guard tubes. • Shorten special section tubes and guard tubes to an extent that the PTO shaft can move

freely in the shortest operating position. • For additional operating instructions refer to the operating instructions of the PTO shaft

manufacturer. Pos: 13.25 /BA/Sicherheit/Gelenkwelle/Achtung - Schwenkbereich/Freiraum überprüfen @ 9\mod_1220536308930_78.docx @ 126898 @ @ 1

Caution! - Swivel range of the PTO shaft Effect: Damage to the tractor or the machine • Check the swivel range and clearance of the PTO shaft!

Pos: 13.26 /BA/Erstinbetriebnahme/Gelenkwelle/Traktorwechsel Gelenkwellenlänge beachten @ 6\mod_1214996938591_78.docx @ 97742 @ @ 1

Caution! - Changing the tractor Effect: Damage to the machine When using the machine for the first time and whenever changing the tractor Check PTO shaft for the correct length. If the length of the PTO shaft does not match the tractor, always observe the chapter entitled "Adjusting the length of the PTO shaft".


Commissioning

28

Pos: 13.28 /Überschriften/Überschriften 2/U-Z/VVerstellstück Aushubzylinder/Entlastungsfeder @ 72\mod_1307514745726_78.docx @ 651448 @ 2 @ 1

5.5 Adjustment Piece for Lifting Cylinder and Compensation Spring Pos: 13.29 /BA/Inbetriebnahme/Mähwerke AM Baureihe/Verstellstück Aushubzylinder/Entlastungsfeder/Verstellstück Aushubzylinder/Entlastungsfeder Bild AM-CV Baureihe @ 72\mod_1307515644349_78.docx @ 651476 @ @ 1

AM 283 CVAM 243 CVAM 203 CV

AM 283 CV + B

2AM-5-000

Fig. 7 Pos: 13.30 /BA/Inbetriebnahme/Mähwerke AM Baureihe/Verstellstück Aushubzylinder/Entlastungsfeder/Verstellstück Aushubzylinder/Entlastungsfeder Text @ 72\mod_1307514666785_78.docx @ 651420 @ @ 1

The lower bearing bolt for the lifting cylinder and the compensation spring must be locked in a specific position depending on the type of the machine.

Pos: 13.31 /BA/Inbetriebnahme/Mähwerke AM Baureihe/Verstellstück Aushubzylinder/Entlastungsfeder/Hinweis Einstellung ist werkseitig montiert und darf nicht verändert werden @ 72\mod_1307514579470_78.docx @ 651393 @ @ 1

Note The setting is mounted in the factory and must not be changed. The bolt (1) is mounted with the lever (2).


Commissioning

29

Pos: 15 /Layout Module /Diese Seite ist bewusst freigelassen worden. @ 1\mod_1201783680373_78.docx @ 54443 @ @ 1

This page has been left blank deliberately!! Pos: 16 /Layout Module /---------------Seitenumbruch---------------- @ 0\mod_1196175311226_0.docx @ 4165 @ @ 1

Start-up

30

Pos: 17.1 /Überschriften/Überschriften 1/F-J/Inbetriebnahme @ 0\mod_1196327075811_78.docx @ 6375 @ 1 @ 1

6 Start-up Pos: 17.2 /Überschriften/Überschriften 2/A-E/AAnbau an den Traktor @ 0\mod_1199717845194_78.docx @ 34039 @ 2 @ 1

6.1 Mounting onto the Tractor Pos: 17.3 /BA/Sicherheit/6. Überarbeitete Warnhinweise/Warnung - Unbeabsichtigtes Abkuppeln angebaute @ 291\mod_1410427253866_78.docx @ 2294307 @ @ 1

Danger! - Inadvertent uncoupling of the machine during road travel or work. Effect: Danger to life, serious injuries or serious damage to the machine. • Use extreme caution when attaching or detaching devices to or from the tractor! The

accident prevention regulations must be complied with absolutely. • The lower suspension arms on the tractor must be fixed in position

with the retaining chains or bars to prevent the machine from swivelling out during transport or work. If the lower suspension arms (1) are equipped with catch hooks, the following items must be taken into consideration:

Especially in the headland position, high forces develop in the lower suspension arm bolts (3) that act upwards in the left-hand hook. For this reason, the catch hooks must be in a flawless condition. Additionally, the catch hooks must be secured in the provided locking hole (4) against unwanted opening after the machine has been connected to the tractor.

Pos: 17.4 /BA/Sicherheit/7. Gefahrenhinweise alt/Mähwerke/Warnung - Achslasten Beeinträchtigung der Lenkfähigkeit @ 9\mod_1220866555985_78.docx @ 128119 @ @ 1

Warning - Impairment of the steerability of the tractor. Effect: Damage to the tractor or the machine. The attachment of implements at the front and rear must not cause exceedance of the max. permissible weight, of the permissible axle loads and of the carrying capacities of the tractor tyres. Even with a fitted rear-mounted accessory unit, the front axle must always be loaded with a minimum 20% service weight of the tractor. Make sure that these prerequisites are met prior to driving.

Pos: 17.5 /BA/Erstinbetriebnahme/Mähwerke AM Baureihe/Ankuppeln Bild AM 203 CV / 243 CV / 283 CV @ 72\mod_1307456041076_78.docx @ 651114 @ @ 1

1

AM-5-010

2

53 4

Fig. 8 Pos: 17.6 /BA/Erstinbetriebnahme/Mähwerke AM Baureihe/Ankuppeln Text AM 203 CV / 243 CV / 283 CV @ 72\mod_1307456211047_78.docx @ 651142 @ @ 1

• Attach the machine onto the lower suspension arm (1) of the tractor • Fasten the top suspension arm (2) onto the top suspension arm connecting point (5) and

secure it Pos: 17.7 /Layout Module /---------------Seitenumbruch---------------- @ 0\mod_1196175311226_0.docx @ 4165 @ @ 1

Start-up

31

Pos: 17.8 /Überschriften/Überschriften 2/F-J/HHydraulik @ 0\mod_1199776034950_78.docx @ 34205 @ 2 @ 1

6.2 Hydraulics Pos: 17.9 /Überschriften/Überschriften 3/P-T/SSpezielle Sicherheitshinweise @ 0\mod_1197301069931_78.docx @ 17662 @ 3 @ 1

6.2.1 Special Safety Instructions Pos: 17.10 /BA/Sicherheit/Hydraulik/Warnung - Anschluss der Hydraulikleitungen @ 0\mod_1199776548685_78.docx @ 34225 @ @ 1

Warning ! - Connection of the hydraulic line Effect: severe injuries due to penetration of hydraulic oil under the skin. • When connecting the hydraulic hoses to the hydraulic system of the tractor, the system

must be relieved of the pressure on either side. • Due to the risk of injury when searching for leaks, always use suitable tools and wear

protective goggles. • Seek medical help immediately should injuries occur! Danger of infection. • Depressurise prior to uncoupling the hydraulic hoses and working on the hydraulic system! • Check the hydraulic hose lines at regular intervals and replace them if damaged or worn!

The replacement hoses must fulfil the technical requirements set by the equipment manufacturer.

Pos: 17.11 /Überschriften/Überschriften 3/F-J/Hydraulikleitungen anschließen @ 0\mod_1199777037794_78.docx @ 34244 @ 3 @ 1

6.2.2 Connecting the hydraulic lines Pos: 17.12 /BA/Sicherheit/Hydraulik/WARNUNG - Vertauschen der Hydraulikkleitungen, wenn EW @ 9\mod_1220871857985_78.docx @ 128182 @ @ 1

Warning - If the hydraulic hoses are interchanged when connecting them to the hydraulic system of the tractor, the functions will be interchanged as well. Effect: Injuries, serious damage to the machine • Identify the hydraulic connections. • Always ensure correct connection between the machine and the tractor. • When engaging the hydraulic hose, the hydraulic control unit must be in float position or in

"lowering" position.

Pos: 17.13 /BA/Sicherheit/Hydraulik/Achtung - Verschmutzung der Hydraulikanlage @ 2\mod_1202393336803_78.docx @ 59155 @ @ 1

Caution! - Soiling of the hydraulic system Effect: Damages to the machine • When connecting the quick couplings, ensure that these are clean and dry. • Note chafing areas or points of contact.

Pos: 17.14 /BA/Sicherheit/Betätigungsseil/GEFAHR! – Unbeabsichtigte Aktionen ausgelöst Betätigungsseil verlegen @ 8\mod_1219298996457_78.docx @ 111447 @ @ 1

Danger! - Unintended actions triggered. Effect: Danger to life, injuries or damage to the machine. • The actuating rope must be routed in such a way that no movements are unintentionally

triggered in any transport or working positions. • The actuating rope must not come into contact with the tractor tyres • Note chafing areas or points of contact.


Start-up

32

Pos: 17.16 /BA/Inbetriebnahme/EasyCut/Hydraulik/Hydraulikanschluss Bild AM-CV Baureihe @ 72\mod_1307516304827_78.docx @ 651506 @ @ 1

3

AM-0-011

2

Fig. 9 Pos: 17.17 /BA/Inbetriebnahme/EasyCut/Hydraulik/Steuergerät 1xEW @ 10\mod_1221486740745_78.docx @ 134020 @ @ 1

A single-action control unit is required on the tractor to operate the machine. Pos: 17.18 /BA/Inbetriebnahme/Mähwerke AM Baureihe/Anschluss Hydraulikleitung AM S / AM CV BAureihe @ 69\mod_1305092471935_78.docx @ 632836 @ @ 1

• Release the pressure from the hydraulic system on the tractor side • Insert the hydraulic hose into the hydraulic coupling of the control valve

Pos: 17.19 /BA/Inbetriebnahme/Mähwerke AM Baureihe/Betätigungsseil ablegen AM S und AM CV Baureihe @ 69\mod_1305092662177_78.docx @ 632864 @ @ 1

• Set down the actuating rope for unlocking the "transport position" at a suitable place in the tractor cab


Start-up

33

Pos: 17.21 /Überschriften/Überschriften 2/F-J/GGelenkwelle @ 0\mod_1199781879794_78.docx @ 34542 @ 2 @ 1

6.3 PTO shaft Pos: 17.22 /BA/Sicherheit/Gelenkwelle/Gefahr - Sich drehende Gelenkwelle_2 @ 0\mod_1199781692950_78.docx @ 34523 @ @ 1

Danger! - Rotating PTO shaft Effect: Danger to life or serious injuries • Install or detach the PTO shaft only with the engine switched off and the ignition key

removed. • Secure the tractor against rolling. • Make sure that the PTO shaft is coupled properly (the lock of the PTO shaft must have

snapped in). • Make sure that the protective devices are attached properly. • Never use a PTO shaft, the protective devices of which have not been attached. • Replace damaged protective devices immediately • Attach the safety chain of the PTO shaft so that the guard tube does not rotate

simultaneously with the PTO shaft.

Pos: 17.23 /BA/Sicherheit/Gelenkwelle/Gefahr - Falsche Zapfwellendrehzahl 540 U/min @ 9\mod_1220868351329_78.docx @ 128138 @ @ 1

Danger! - Incorrect PTO speed Effect: Danger to life, serious injuries or damage to the machine. • This machine may only be driven with a max. PTO speed of 540 rpm. • Before switching on the PTO, make sure that you have selected the correct PTO speed.

Pos: 17.24 /BA/Sicherheit/Gelenkwelle/Achtung - Schwenkbereich/Freiraum überprüfen @ 9\mod_1220536308930_78.docx @ 126898 @ @ 1

Caution! - Swivel range of the PTO shaft Effect: Damage to the tractor or the machine • Check the swivel range and clearance of the PTO shaft!

Pos: 17.25 /Überschriften/Überschriften 2/F-J/GGelenkwelle montieren @ 2\mod_1202398342788_78.docx @ 59253 @ 2 @ 1

6.4 Install the PTO shaft Pos: 17.26 /BA/Inbetriebnahme/Mähwerke AM Baureihe/Anbau Gelenkwelle Bild AM-CV Baureihe @ 73\mod_1307608792021_78.docx @ 652982 @ @ 1

AM-0-002-5

1

Fig. 10 Pos: 17.27 /BA/Inbetriebnahme/Mähwerke AM Baureihe/Anbau Gelenkwelle Text AM-CV @ 73\mod_1308136641780_78.docx @ 655117 @ @ 1

• Slide the PTO shaft (1) onto the gear input shaft of the disc mower and secure it • Slide the PTO shaft (1) onto the PTO end of the tractor and secure it Make sure all locks of the PTO shaft have snapped in. • Secure the PTO shaft guard against turning with the retaining chain


Start-up

34

Pos: 17.29 /Überschriften/Überschriften 2/U-Z/ZZwischengelenkwelle @ 3\mod_1204702241039_78.docx @ 71481 @ 2 @ 1

6.5 Intermediate PTO shaft Pos: 17.30 /BA/Inbetriebnahme/EasyCut/Anbau Gelenkwelle/Zwischengelenkwelle/Zwischengelenkwelle Bild AM-CV Baureihe @ 72\mod_1307511143020_78.docx @ 651283 @ @ 1

AM-4-009-1

2

1 3

Fig. 11 Pos: 17.31 /BA/Inbetriebnahme/EasyCut/Anbau Gelenkwelle/Zwischengelenkwelle/Zwischengelenkwelle mit Freilauf Text EC 280/320 CV-Q @ 10\mod_1221488055292_78.docx @ 134083 @ @ 1

The intermediate PTO shaft for the tedder drive is coupled to the gearbox via the friction clutch (1) and to the tedder via the free-wheel (2). Fasten support chain (3) to the mower.

Pos: 17.32 /BA/Inbetriebnahme/EasyCut/Hinweis Reibkupplung @ 11\mod_1223358975938_78.docx @ 145593 @ @ 1

Note - Friction Clutch Effect: Conserve functionality and increased service life • The friction clutch (2) must be vented prior to commissioning and once a year prior to

harvesting. (See section Before the Start of the New Season "Friction clutch")

Pos: 17.33 /Überschriften/Überschriften 2/A-E/AAbstellstütze @ 17\mod_1236317851151_78.docx @ 204315 @ 2 @ 1

6.6 Parking support Pos: 17.34 /BA/Bedienung /EasyCut/Abstellstütze/Achtung Abstellstütze muss eingeschoben sein @ 72\mod_1307513370887_78.docx @ 651311 @ @ 1

Caution! -Parking support not pushed in! Effect: Damage to the machine • Make certain before road/transport travel and for work that the parking support is pushed in

and secured

Pos: 17.35 /BA/Bedienung /EasyCut/Abstellstütze/Abstellstütze eingeklappt Bild AM CV-Baureihe @ 72\mod_1307513657421_78.docx @ 651339 @ @ 1

AM-1-078-1

1

Fig. 12 Pos: 17.36 /BA/Bedienung /EasyCut/Abstellstütze/Abstellstütze in Transportstellung einschieben @ 72\mod_1307514187806_78.docx @ 651367 @ @ 1

After the machine is attached, push the parking support into the transport position. • Use the three-point hydraulic system to raise the parking support somewhat • Push the parking support (1) into the transport position and secure it


Start-up

35

Pos: 17.38.1 /BA/Inbetriebnahme/Mähwerke AM Baureihe/Entlastungsfeder/Entlastungsfeder befestigen @ 69\mod_1305094434033_78.docx @ 632917 @ 2 @ 1

6.7 Fastening the Compensation Spring Pos: 17.38.2 /BA/Inbetriebnahme/Mähwerke AM Baureihe/Entlastungsfeder/GEFAHR! – Montage der Entlastungsfeder(n) @ 69\mod_1305096039051_78.docx @ 633110 @ @ 1

DANGER! – Installing the compensation spring(s) Effect: Danger to life or serious injuries • The compensation spring(s) should only be adjusted while the machine is in the transport

position. In the working position the compensation springs are subject to high tensile stress.• Severe injury can be caused if the compensation spring(s) is/are removed while in the

working position. • The lower threaded blocks on the compensation spring(s) must be fully screwed in.

Pos: 17.38.3 /BA/Inbetriebnahme/Mähwerke AM Baureihe/Entlastungsfeder/Hinweis Die hintere Entlastungsfeder kann nur in Transportstellung der Maschine montiert werden @ 69\mod_1305095664117_78.docx @ 633029 @ @ 1

Note The rear compensation spring can only be mounted in the transport position of the machine.

Pos: 17.38.4 /BA/Inbetriebnahme/Mähwerke AM Baureihe/Entlastungsfeder/Entlastungsfeder An- Abbau Bild AM-CV Baureihe @ 72\mod_1307510034549_78.docx @ 651253 @ @ 1

AM-1-084-021

4 5

3

AM-0-011

2

Fig. 13 Pos: 17.38.5 /BA/Inbetriebnahme/Mähwerke AM Baureihe/Entlastungsfeder/Entlastungsfeder Text CV @ 69\mod_1305095555287_78.docx @ 632975 @ @ 1

• Bring the machine into the transport position • Make certain the hook of the transport interlock (4) engages in the eye (5) on the

conditioner housing • Close the shut-off valve on the hydraulic hose (3) • Remove the cotter pin (1) and washer (2) from the upper retaining bolt (spacer sleeve

remains on the bolt) • Push the compensation spring (3) onto the retaining bolt • Mount the washer and cotter pin again


Driving and Transport

36

Pos: 19.1 /Überschriften/Überschriften 1/F-J/Fahren und Transport @ 0\mod_1196330049217_78.docx @ 6553 @ 1 @ 1

7 Driving and Transport Pos: 19.2 /BA/Sicherheit/Fahren und Transport/Warnung - Transport / Straßenfahrt @ 295\mod_1412076613597_78.docx @ 2318257 @ @ 1

WARNING! - Transport travel on roads Accidents may occur when the following points are not observed during transport travel on roads. Thus there is a risk of serious injuries or death. • When driving on public roads, the provisions of the Road Traffic Licensing Regulations

must be adhered to (lighting, identification, axle loads, permissible measurement of additional housing component, etc.)!

• When being transported on public roads, the mower must be lifted. • In the transport position of the mower, always observe the larger height of the vehicle. • Riding on the mower is not permitted.

Pos: 19.3 /BA/Sicherheit/Fahren und Transport/Absperrhahn/Transport / Straßenfahrt Absperrhahn schließen/Schutz einrasten EC 280/320 @ 10\mod_1221540227604_78.docx @ 134129 @ @ 1

Danger! - Transport / road travel Effect: Danger to life, serious injuries or serious damage to the machine. • In transport position, always close the hydraulic shut-off valve. • Always make certain that the lock (1) has snapped into place.

Pos: 19.4 /Überschriften/Überschriften 2/U-Z/VVon Arbeitsstellung in Transportstellung @ 2\mod_1202466246542_78.docx @ 59681 @ 2 @ 1

7.1 Switching from working position to transport position Pos: 19.5 /BA/Sicherheit/6. Überarbeitete Warnhinweise/Warnung-Hochschwenken des Mähwerks in Transportstellung @ 291\mod_1410444332756_78.docx @ 2295038 @ @ 1

WARNING! During the swivelling operation of the mower, persons may be gripped by the mower and be seriously injured. • Before swivelling the mower up into transport position, turn off the PTO shaft. • Do not swivel up the machine until

• all machine parts have come to a complete stop. • there is no one in the swivel range.


Driving and Transport

37

Pos: 19.7 /BA/Fahren und Transport/Mähwerke AM Baureihe/Fahren-Transport Bild AM-CV Baureihe @ 72\mod_1307521161070_78.docx @ 651590 @ @ 1

34

AM-1-058 AM-1-059

1 2

Fig. 14 Pos: 19.8 /BA/Fahren und Transport/Mähwerke AM Baureihe/Fahren/Transport Text AM-CV Baureihe @ 72\mod_1307521115796_78.docx @ 651562 @ @ 1

During transport / road travel the disc mower must be folded up. To do this: • To release the lock (2), pull the actuating rope (1) up from the tractor (hold the actuating

rope drawn taut until the mowing unit has reached the transport position) • Actuate the control valve for the hydraulic cylinder on the tractor. The mowing unit lifts up

into the transport position • Release the actuating rope so that the hook of the transport interlock (1) engages in the eye

(2) on the conditioner housing • Close the shut-off valve on the hydraulic hose

Pos: 19.9 /Überschriften/Überschriften 2/A-E/BBeleuchtung @ 0\mod_1195658399935_78.docx @ 1881 @ 2 @ 1

7.2 Lighting Pos: 19.10 /BA/Fahren und Transport/Mähwerke AM Baureihe/Beleuchtung Bild AM-CV Baureihe @ 72\mod_1307522519939_78.docx @ 651644 @ @ 1

AM-1-075

Fig. 15 Pos: 19.11 /BA/Fahren und Transport/Mähwerke AM Baureihe/Beleuchtung Text @ 69\mod_1305100479350_78.docx @ 633336 @ @ 1

• Push the lighting (1) into the light holder (2) from above • Secure it with a cotter pin • Check function


Operation

38

Pos: 21.1 /Überschriften/Überschriften 1/A-E/Bedienung @ 0\mod_1199789505403_78.docx @ 34825 @ 1 @ 1

8 Operation Pos: 21.2 /Überschriften/Überschriften 2/U-Z/VVon Transport in Arbeitsstellung @ 2\mod_1202466185276_78.docx @ 59662 @ 2 @ 1

8.1 From transport into working position Pos: 21.3 /BA/Sicherheit/7. Gefahrenhinweise alt/Mähwerke/Gefahr - Absenken des Mähwerks in Arbeitsstellung EC 280/320 @ 9\mod_1220879244798_78.docx @ 128439 @ @ 1

Danger! - Lowering the mowing unit into the working position Effect: Danger to life, injuries or damage to the machine. • Lower the mowing unit only when you are absolutely sure that neither persons, animals nor

objects are in the swivel range of the mowing unit. • Switch on the PTO only when the mowing unit is resting on the ground.

Pos: 21.4 /BA/Sicherheit/7. Gefahrenhinweise alt/Mähwerke/Gefahr - Verriegelung prüfen EC 280/320 @ 9\mod_1220879526173_78.docx @ 128463 @ @ 1

Danger! - Check whether the locking mechanism (1) is folded down completely. Effect: Danger to life, serious injuries or serious damage to the machine. The folded-down locking mechanism secures the mowing unit against inadvertent lifting while the machine is running.

Pos: 21.5 /BA/Bedienung /Mähwerke AM Baureihe/Von Transport in Arbeitsstellung Bild AM-CV BAureihe @ 72\mod_1307524802904_78.docx @ 651702 @ @ 1

3

AM-0-011

2

AM-1-083-1

1

Fig. 16 Pos: 21.6 /BA/Bedienung /Mähwerke AM Baureihe/Von Transport in Arbeitsstellung Text AM-CV Baureihe @ 72\mod_1307524954964_78.docx @ 651730 @ @ 1

• Open the hydraulic shut-off valve (3) on the hydraulic hose • To lower the mowing unit, pull up the lock (1) from the tractor using the actuating rope (2) • Activate the double action control valve on the tractor to slowly lower the mowing unit


Operation

39

Pos: 21.8 /Überschriften/Überschriften 2/U-Z/VVor dem Mäheinsatz @ 3\mod_1204788384465_78.docx @ 73168 @ 2 @ 1

8.2 Before mowing Pos: 21.9 /BA/Sicherheit/7. Gefahrenhinweise alt/Mähwerke/Warnung - Unerwartete Bewegung der Schneidwerkzeuge bzw. des Mähwerkes @ 299\mod_1412937148121_78.docx @ 2341087 @ @ 1

WARNING! Foreign bodies may be hurled up during the operation. Thus there is a risk for persons staying in the danger zone to be seriously hurt or killed. Therefore the following points must be observed before the machine is used: • The mower must be in working position. • Move protective equipment into protective position and make sure that it is not damaged. • Replace damaged protective equipment immediately. • Instruct persons to leave the danger zone. • Special care should be taken when working near roads and buildings. • Make sure each time before the mower is used that blades, retaining bolts, leaf springs and

cutting discs or mower drums are not damaged, worn or missing; replace them, if necessary!

Pos: 21.10 /BA/Bedienung /EasyCut/Hinweis Beim Mähen Steuerventil schwimmstellung/senken @ 9\mod_1220881412391_78.docx @ 128661 @ @ 1

Note! - While mowing Effect: Proper use of the machine • Leave control unit(s) in the "Lower" or "Float position" position for work.

Pos: 21.11 /Überschriften/Überschriften 3/P-T/SSchutzeinrichtung herunterklappen @ 9\mod_1220881079079_78.docx @ 128594 @ 3 @ 1

8.2.1 Folding down the Safety Device Pos: 21.12 /BA/Sicherheit/7. Gefahrenhinweise alt/Mähwerke/Gefahr - Fortschleudern von Steinen @ 84\mod_1318311844997_78.docx @ 733435 @ @ 1

DANGER! – Stones forcibly projected during operation Effect: Danger to life or serious injuries. • Check the guard cloths regularly. Worn or damaged guard cloths must be replaced! • The protective equipment on the mowing unit, e.g. cloths and hoods, protects against flying

stones and similar objects, and also prevents access to dangerous parts. Because of this, you must always move it to its protective position before starting work

• Fold the side plate(s) down and secure with twist locks before use


Operation

40

Pos: 21.14 /Überschriften/Überschriften 2/A-E/AArbeitseinsatz @ 5\mod_1213258631763_78.docx @ 87907 @ 2 @ 1

8.3 Using the Machine for Work Pos: 21.15 /BA/Sicherheit/7. Gefahrenhinweise alt/Mähwerke/Gefahr - Arbeitseinsatz / Mähen @ 73\mod_1307695972255_78.docx @ 654926 @ @ 1

DANGER! - Using the machine for work Effect: Danger to life, injuries or damage to the machine. • The glide skids must rest on the ground before start-up and during work • Maintain an adequate safety distance from the cutting tools during operation • There is danger of foreign objects being forcibly ejected even when the machine is

operated properly. Persons must therefore be directed out of the danger zone of the machine.

• Special care should be taken when working near roads and buildings)

Pos: 21.16 /Überschriften/Überschriften 2/U-Z/VVorgewendestellung @ 0\mod_1196414916041_78.docx @ 8116 @ 2 @ 1

8.4 Headland Position Pos: 21.17 /BA/Sicherheit/Vorgewendestellung/Gefahr - Vorgewende Mähwerke EC 280/320 @ 9\mod_1220881723360_78.docx @ 128683 @ @ 1

Danger! - Lifting the mowing unit from the working position into headland position Effect: Danger to life, injuries or damage to the machine. • Lift the mowing unit into headland position only when you are absolutely sure that neither

persons, animals nor objects are in the swivel range of the mowing unit. • During driving in the headland position, the mowing unit will only be raised or lowered by

the hydraulic cylinder of the disc mower. The locking mechanism for folding up the mowing unit must not be actuated.

Pos: 21.18 /BA/Bedienung /EasyCut/Heck/Vorgewende @ 9\mod_1220881871173_78.docx @ 128704 @ @ 1

In headland position, lift the disc mower by activating the single-action control unit on the tractor side.


Operation

41

Pos: 21.20 /Überschriften/Überschriften 2/A-E/AAbbau der Maschine @ 3\mod_1204792387824_78.docx @ 73245 @ 2 @ 1

8.5 Detaching the machine Pos: 21.21 /BA/Sicherheit/EasyCut/Gefahr - Maschine abstellen_mit Hydraulikschlauch @ 9\mod_1220883208423_78.docx @ 128830 @ @ 1

Danger! - Unexpected movements of the machine Effect: Danger to life, serious injuries • No one is permitted inside the danger zone. • Park the machine on a solid and even surface. • You should not unhitch the machine until the engine has been switched off and the ignition

key has been removed. • Secure the tractor against rolling. • Use extreme caution when attaching implements to or detaching them from the tractor! The

accident prevention regulations must be complied with absolutely. • When connecting the hydraulic hose to and disconnecting it from the hydraulic system of

the tractor, the tractor system as well as the machine system must be depressurised! Move the appropriate control valves into the flow position.

• When detaching the machine, do not walk between the tractor and the machine!

Pos: 21.22 /BA/Sicherheit/7. Gefahrenhinweise alt/Einstellarbeiten / Einstellungen/Gefahr - Einstellung an den Entlastungsfedern nur in Transportstellung Mähwerke @ 9\mod_1220883469610_78.docx @ 128852 @ @ 1

Danger! - Setting on the compensation springs Effect: Danger to life or serious injuries • The compensation springs should be adjusted only while the machine is in the transport

position. In the working position the compensation springs are subject to high tensile stress.• Severe injury can be caused if the compensation springs are removed while in the working

position. • The lower threaded blocks on the compensation springs must be fully screwed in.

Pos: 21.23 /BA/Inbetriebnahme/Mähwerke AM Baureihe/Entlastungsfeder/Entlastungsfeder An- Abbau Bild AM-CV Baureihe @ 72\mod_1307510034549_78.docx @ 651253 @ @ 1

AM-1-084-021

4 5

3

AM-0-011

2

Fig. 17 Pos: 21.24 /BA/Bedienung /Mähwerke AM Baureihe/Entlastungsfedern außer Funktion setzen AM-CV Baureihe @ 73\mod_1307526758809_78.docx @ 651758 @ @ 1

To simplify later attachment of the disc mower to the tractor, it is advisable to remove the rear compensation spring (2). To do this: • Bring the machine to the transport position (the compensation spring(s) may only be

removed in this position) • Make certain the hook of the transport interlock (4) engages in the eye (5) on the

conditioner housing • Close the shut-off valve on the hydraulic hose (3) • Pull out the cotter pin (1) on the upper retaining bolt of the rear compensation spring (2) • Remove the washer • Pull the compensation spring out of the top retaining bolt and set it down on the support • Open the shut-off valve (3) on the hydraulic hose of the disc mower • To lower the mowing unit, pull up the lock from the tractor using the actuating rope (2) • Activate the double action control valve on the tractor to slowly lower the mowing unit

Pos: 21.25 /BA/Bedienung /Mähwerke AM Baureihe/Abbau Teil 2 AM-CV Baureihe @ 73\mod_1308210707255_78.docx @ 655288 @ @ 1

Operation

42

AM-1-061-2

21

3

AM-0-011

2

Fig. 18 • Lower the parking support (2) and tighten the clamp (1) to secure it. • Disconnect the hydraulic hose (3) from the tractor (set the dust cap in place) • Take the actuating rope (2) off the tractor

Pos: 21.26 /BA/Bedienung /Mähwerke AM Baureihe/Gelenkwelle abkuppeln Bild AM 203S/243S/283S/323S @ 69\mod_1305104107656_78.docx @ 633782 @ @ 1

1

AMS-0-036

Fig. 19 Pos: 21.27 /BA/Bedienung /Mähwerke AM Baureihe/Gelenkwelle abkuppeln Text AM 203S/243S/283S/323S @ 69\mod_1305104177615_78.docx @ 633810 @ @ 1

• Remove the safety chain from the PTO shaft guard • Pull the PTO shaft off the tractor PTO and set it down on the PTO shaft support (1) • Disconnect the disc mower from the top suspension arm and lower suspension arms of the

tractor Pos: 22 /Layout Module /---------------Seitenumbruch---------------- @ 0\mod_1196175311226_0.docx @ 4165 @ @ 1

Operation

43

Pos: 23 /Layout Module /Diese Seite ist bewusst freigelassen worden. @ 1\mod_1201783680373_78.docx @ 54443 @ @ 1

This page has been left blank deliberately!! Pos: 24 /Layout Module /---------------Seitenumbruch---------------- @ 0\mod_1196175311226_0.docx @ 4165 @ @ 1

Settings

44

Pos: 25.1 /Überschriften/Überschriften 1/A-E/Einstellungen @ 0\mod_1199868783862_78.docx @ 36141 @ 1 @ 1

9 Settings Pos: 25.2 /BA/Sicherheit/7. Gefahrenhinweise alt/Mähwerke/Warnung - Einstellarbeiten angebaute Maschinen @ 254\mod_1397487875458_78.docx @ 1953794 @ @ 1

DANGER! - Unexpected movement of the machine Effect: Danger to life or serious injuries. • Setting tasks must only be performed when the drive is switched off and the engine is at a

standstill! • Switch off engine. • Remove the ignition key and carry it with you. • Secure the tractor against rolling away.

Pos: 25.3 /BA/Einstellungen/Mähwerke/Mähwerke AM Baureihe/Einstellung des Oberlenkerkoppelpunktes @ 73\mod_1307532879378_78.docx @ 651895 @ 2 @ 1

9.1 Setting of the top suspension arm connecting point

1

AM- 1-062

2

aa

Fig. 20 In the basic setting of the threaded spindle (2) on the top suspension arm connecting point, the bolt (1) is centred on the threaded spindle. The "a" distances are equal.

Pos: 25.4 /Überschriften/Überschriften 2/A-E/EEinstellen der Schnitthöhe @ 0\mod_1196660879619_78.docx @ 9191 @ 2 @ 1

9.2 Adjusting the cutting height Pos: 25.5 /BA/Einstellungen/Mähwerke/Schnitthöhe/Schnitthöhe Bild AM-CV Baureihe @ 73\mod_1307532356537_78.docx @ 651812 @ @ 1

1AM-1-053

32

Fig. 21 Pos: 25.6 /BA/Einstellungen/Mähwerke/Schnitthöhe/Schnitthöhe einstellen AM-CV Baureihe @ 73\mod_1307532492259_78.docx @ 651840 @ @ 1

Due to the disc mower's weight, it is difficult if not impossible to set the cutting height with the top suspension arm. The cutting height adjustment can be set with the crank (3). The inclination of the disc mower and thus the cutting height is set by the threaded spindle (2) on the top suspension arm connecting point (1).

Pos: 25.7 /BA/Einstellungen/Mähwerke/Schnitthöhe/Hinweis Unterlenker am Traktor mit Begrenzungsketten oder -stangen so befestigen @ 73\mod_1307532695645_78.docx @ 651868 @ @ 1

Note Fasten the lower suspension arm onto the tractor with retaining chains or bars so that the mower does not swing out during transport or mowing!


Settings

45

Pos: 25.9 /Überschriften/Überschriften 2/A-E/EEinstellung der Entlastungsfedern @ 0\mod_1196666659447_78.docx @ 10133 @ 2 @ 1

9.3 Adjusting the Compensation Springs Pos: 25.10 /BA/Sicherheit/7. Gefahrenhinweise alt/Mähwerke/Gefahr - Einstellung an den Entlastungsfedern @ 0\mod_1196751594562_78.docx @ 12575 @ @ 1

Danger! - Setting on the compensation springs Effect: Danger to life or serious injuries • The compensation springs must only be removed in transport position. In the working

position the compensation springs are subject to high tensile stress. • Severe injury can be caused if the compensation springs are removed while in the working

position. • The lower threaded blocks on the compensation springs must be fully screwed in.

Pos: 25.11 /BA/Einstellungen/Mähwerke/EasyCut/Bodendruck/Bodendruck allgemeiner Text alle EC @ 0\mod_1196667271181_78.docx @ 10190 @ @ 1

The ground pressure for the cutter bar is adjusted to local conditions by means of the compensation springs. In order to protect the sward the load on the mowing spar must be relieved so that it does not jump when mowing, yet does not leave any skid marks on the ground.

Pos: 25.12 /BA/Einstellungen/Mähwerke/Mähwerke AM Baureihe/Einstellen der Entlastungsfeder(n) Bild AM-CV Baureihe @ 73\mod_1307534057218_78.docx @ 651978 @ @ 1

1

2

5 4

3

6

AM-1-084/1 AM-1-084/2

a b

Fig. 22 Pos: 25.13 /BA/Einstellungen/Mähwerke/Mähwerke AM Baureihe/Hinweis Die Federn (2) und (3) entlasten den Mähholm an der Außenseite. @ 73\mod_1308228901018_78.docx @ 655316 @ @ 1

Note Springs (2) and (3) relieve the cutter bar on the outside.

Pos: 25.14 /BA/Einstellungen/Mähwerke/Mähwerke AM Baureihe/Hinweis Die Feder (4) entlastet den Mähholm an der Innenseite. @ 73\mod_1308228972907_78.docx @ 655371 @ @ 1

Note Spring (4) relieves the cutter bar on the inside.

Pos: 25.15 /BA/Einstellungen/Mähwerke/Mähwerke AM Baureihe/Einstellen der Entlastungsfeder(n) Text Teil 1 AM-CV Baureihe @ 73\mod_1307533229516_78.docx @ 651922 @ @ 1

• Bring the machine into the transport position

CAUTION! Make absolutely certain that the transport interlock (6) is engaged in transport position.

• Remove the compensation springs (2,3) in the transport position of the disc mower from the

top retaining bolt (1) • Turn the upper adjustment pieces to change the length The further the adjustment pieces are screwed in, the greater the relief on the mowing unit. • After the setting is made, attach the compensation spring on the retaining bolt again and

secure it with a washer and cotter pin


Settings

46

Pos: 25.17 /BA/Einstellungen/Mähwerke/Mähwerke AM Baureihe/Einstellen der Entlastungsfeder(n) Text Teil 2 AM-CV Baureihe @ 73\mod_1307533716032_78.docx @ 651950 @ @ 1

• The compensation spring (4) can be adjusted with the spindle (5) Pos: 25.18 /BA/Einstellungen/Mähwerke/Mähwerke AM Baureihe/Einstellen der Entlastungsfedern Grundeinstellung AM-CV Baureihe @ 73\mod_1307534200876_78.docx @ 652006 @ @ 1

Basic Setting: Distance "a" = 80 mm Distance "b" = 60 mm

Pos: 25.19 /BA/Einstellungen/Mähwerke/Mähwerke AM Baureihe/Hinweis bei zwei Entlastungsfedern beide gleich einstellen @ 69\mod_1305107374613_78.docx @ 634228 @ @ 1

Note In disc mowers with two compensation springs, the two compensation springs must be set to the same length.

Pos: 25.20 /Überschriften/Überschriften 2/A-E/EEinstellung der Pfahlsicherung @ 9\mod_1220961168693_78.docx @ 130388 @ 2 @ 1

9.4 Setting of the pole protection mechanism Pos: 25.21 /BA/Sicherheit/EasyCut/Achtung - Einstellung an der Pfahlsicherung @ 9\mod_1220960955600_78.docx @ 130367 @ @ 1

Caution! - Adjusting the pole protection mechanism Effect: Damage to the machine • If the setting value is changed, the trigger moment will also change. If the spring on the

pole protection mechanism is pretensioned more than prescribed by the manufacturer, there is a risk of damaging the disc mower.

• The spring on the pole protection mechanism must be tensioned at least to the extent that the pole protection mechanism does not respond in transport position even with abrupt loads.

Pos: 25.22 /BA/Einstellungen/Mähwerke/EasyCut/Pfahlsicherung/Pfahlsicherung Bild AM 203S/243S/283S/323S @ 69\mod_1305105171394_78.docx @ 634013 @ @ 1

Fig. 23 Pos: 25.23 /BA/Einstellungen/Mähwerke/EasyCut/Pfahlsicherung/Pfahlsicherung allgemein @ 9\mod_1220961293021_78.docx @ 130429 @ @ 1

In order to protect the disc mower against damages during driving over obstacles, it is equipped with a so-called pole protection mechanism. The optimal setting for the trigger moment takes place in the factory.

Pos: 25.24 /BA/Einstellungen/Mähwerke/EasyCut/Pfahlsicherung/Pfahlsicherung AM-CV Baureihe Tabelle @ 73\mod_1307534335269_78.docx @ 652035 @ @ 1

Mower type Dimension x AM 203 CV 81 mm AM 243 CV 80 mm AM 283 CV 79 mm

AM 283 CV +B 79 mm

Pos: 25.25 /BA/Einstellungen/Mähwerke/EasyCut/Pfahlsicherung/Pfahlsicherung nach dem Auslösen @ 9\mod_1220961640381_78.docx @ 130471 @ @ 1

After the pole protection mechanism is triggered, the mowing unit swings back and, at the same time, in the front area upwards. This allows the mower to climb over small obstacles, e.g., stones. The pole protection mechanism will catch again as soon as you move back.

Pos: 25.26 /BA/Einstellungen/Mähwerke/EasyCut/Pfahlsicherung/Hinweis Der Bolzen der Auslöseklinke muss immer gefettet sein. @ 69\mod_1305105580435_78.docx @ 634067 @ @ 1

Note The bolt of the trigger cam disc must always be greased.


Settings

47

Pos: 25.28 /Überschriften/Überschriften 2/F-J/GGrundeinstellung der Traktor-Unterlenker @ 73\mod_1307536423195_78.docx @ 652061 @ 2 @ 1

9.5 Default Setting of the Tractor's Lower Suspension Arms Pos: 25.29 /BA/Einstellungen/Mähwerke/Mähwerke AM Baureihe/Grundeinstellung der Traktor-Unterlenker Bild AM-S und AM-CV @ 73\mod_1307536515692_78.docx @ 652088 @ @ 1

Fig. 24 Pos: 25.30 /BA/Einstellungen/Mähwerke/Mähwerke AM Baureihe/Grundeinstellung der Traktor-Unterlenker Text AM-CV Baureihe @ 73\mod_1307536599843_78.docx @ 652116 @ @ 1

The optimum height is set when the connecting rod (1) is in the oblong hole (2) at a distance of about a = 90 mm. If it is not located here, the height must be changed as required by raising or lowering the lower suspension arm.


Settings

48

Pos: 25.32 /Überschriften/Überschriften 2/A-E/EEinstellung der Zetterdrehzahl @ 0\mod_1196668564463_78.docx @ 10266 @ 2 @ 1

9.6 Adjusting the Tedder Speed Pos: 25.33 /BA/Sicherheit/7. Gefahrenhinweise alt/Einstellarbeiten / Einstellungen/Gefahr - Einstellungen an der Maschine @ 0\mod_1196668628056_78.docx @ 10285 @ @ 1

Danger! - Settings on the machine Effect: Danger to life, injuries or damage to the machine. • Setting tasks must only be performed when the drive is switched off and the engine is at a

standstill! Remove the ignition key!

Pos: 25.34 /BA/Einstellungen/Mähwerke/Zetterdrehzahl/Zetterdrehzahl Bild AM-CV Baureihe @ 73\mod_1307536833481_78.docx @ 652144 @ @ 1

AM-0-007

1 2

A 0 B AM-0-008

3

2

1

Fig. 25 Pos: 25.35 /BA/Einstellungen/Mähwerke/Zetterdrehzahl/Zetterdrehzahl einstellen 600/900 AM-CV Baureihe @ 73\mod_1307536928332_78.docx @ 652172 @ @ 1

Two tedder speeds can be set on the speed gearbox. This affects the conditioning effect and the power consumption. Position "A" = minimum speed: 600 rpm (multifoliate crop) Position "B" = maximum speed: 900 rpm (stalk crop) Position "0" = middle position (idle) • Remove the safety cotter pin (2) • Pull out the actuating lever (1) or push it in to set the required speed

Note Turning the screw (3) with the spanner included with delivery facilitates the switching process on the actuating lever (1)

• Secure the actuating lever (2) with the safety cotter pin (1)


Settings

49

Pos: 25.37 /Überschriften/Überschriften 2/A-E/EEinstellen des Aufbereitungsblechs @ 0\mod_1196670615681_78.docx @ 10399 @ 2 @ 1

9.7 Adjusting the conditioner plate Pos: 25.38 /BA/Einstellungen/Mähwerke/Einstellung des Aufbereitungsbleches Bild AM-CV Baureihe @ 73\mod_1307543072851_78.docx @ 652394 @ @ 1

AM-1-073

1

Fig. 26 Pos: 25.39 /BA/Einstellungen/Mähwerke/Einstellung des Aufbereitungsbleches Text AM-CV Baureihe @ 73\mod_1307542906131_78.docx @ 652366 @ @ 1

The conditioning of the mowed crop can be influenced by adjusting the conditioning plate with the crank (1). The setting depends on the desired degree of conditioning of the crop. • Moving the conditioner plate closer to the tine conditioner means more intensive

conditioning • Moving the conditioner plate further from the tine conditioner means less intensive

conditioning Always check the tedder for damaged tines before the machine is used: Straighten any bent tines. Replace any broken tines.

Pos: 25.40 /Überschriften/Überschriften 2/A-E/EEinstellung der Schwadbreite @ 73\mod_1307539778398_78.docx @ 652200 @ 2 @ 1

9.8 Adjusting the Swath Width Pos: 25.41 /BA/Einstellungen/Mähwerke/Schwadbreite / Breitablage/Einstellung der Schwadablage Bild AM-CV Baureihe @ 73\mod_1307540283409_78.docx @ 652228 @ @ 1

1

2

AM-1-065

Fig. 27 Pos: 25.42 /BA/Einstellungen/Mähwerke/Schwadbreite / Breitablage/Einstellung der Schwadablage Text EC280/320 CV-Q @ 10\mod_1221551972416_78.docx @ 134968 @ @ 1

The swath width is adjusted by the swath flaps (1) on the rear of the machine. The swath flaps are locked in position by means of the ring nuts.


Settings

50

Pos: 25.44 /Überschriften/Überschriften 2/A-E/EEinstellung Zetterwalze @ 73\mod_1307597779578_78.docx @ 652425 @ 2 @ 1

9.9 Setting of the tine conditioner Pos: 25.45 /BA/Einstellungen/Mähwerke/Einstellung Zetterwalze AM-CV Bild @ 73\mod_1307607084046_78.docx @ 652925 @ @ 1

AM-1-089

21

Fig. 28 Pos: 25.46 /BA/Einstellungen/Mähwerke/Einstellung Zetterwalze AM-CV Teil 1 @ 73\mod_1307598074765_78.docx @ 652452 @ @ 1

The tine conditioner (1) with the V-tines (2) has four different settings. The setting controls the distance from the tedder to the cutter bar.

Pos: 25.47 /BA/Sicherheit/7. Gefahrenhinweise alt/Achtung - gebrochene Zinken @ 0\mod_1196670786291_78.docx @ 10437 @ @ 1

Caution! - Damaged or missing tines Effect: Damages to the machine. • Bent and broken prongs cause an imbalance. • Straighten any bent tines. • Replace any broken tines.

Pos: 25.48 /BA/Einstellungen/Mähwerke/Einstellung Zetterwalze AM-CV Teil 2 @ 73\mod_1307598241536_78.docx @ 652479 @ @ 1

2 1

21

AM-1-068

Fig. 29 • Remove the locking screws (1) for the gear segment on the right-hand and left-hand side of

the machine • Turn the right or left gearwheel (2) to turn the gear segment until the desired position is

reached. • Fit the locking screws (1) for the gear segment on the right-hand and left-hand side of the

machine


Settings

51

Pos: 25.50 /BA/Einstellungen/Mähwerke/Einstellung Zetterwalze AM-CV Teil 3 @ 73\mod_1307598800484_78.docx @ 652507 @ @ 1

1 2

3

I

II

III

IV

AM-1-069

Fig. 30 Position of the tine conditioner relative to the cutter bar: I : Basic setting II : Setting for longer crop located closer to the mower III: Setting for very long crop located closer to the mower IV: Tedder out of operation

Note The tedder must not be operated in position IV. Remove the PTO shaft completely from the machine. Switch the speed gearbox to position "0".

Pos: 25.51 /BA/Einstellungen/Mähwerke/Einstellung Zetterwalze AM-CV Teil 4 Ruhestellung @ 73\mod_1307599042691_78.docx @ 652535 @ 3 @ 1

9.9.1 Deactivating the tine conditioner

1

2

43

AM-4-072-1

Fig. 31 Before the tine conditioner is deactivated (1) (position IV= out of operation), the PTO shaft (4) must be completely removed (including from the speed gearbox). Switch the speed gearbox to position "0".

Note The PTO shaft guard (2) can only be moved past on the spacer (3) when the PTO shaft has been pulled out.


Settings

52

Pos: 25.53 /BA/Einstellungen/Mähwerke/Schwadbreite / Breitablage/Breitschwadhaube AM CV + B Ausführung @ 73\mod_1307540867392_78.docx @ 652256 @ 2 @ 1

9.10 Wide Swath Cover

Basic setting Disc mowers AM 243 CV + B and AM 283 CV + B are equipped with a wide swath cover. Mowed grass is distributed evenly over the entire surface by the V-shaped steel tine conditioner. In this way the entire surface is used for pre-wilting the forage. The deflector plate (1) is fastened in the basic setting in the marked bore holes.

AM-4-012

1

Fig. 32

AM-97-01

1

Fig. 33


Settings

53

Pos: 25.55 /BA/Einstellungen/Mähwerke/Schwadbreite / Breitablage/Einstellen auf Schwadablage AM-CV Baureihe @ 73\mod_1307541081938_78.docx @ 652283 @ 3 @ 1

9.10.1 Making Adjustments for Swathing

If necessary the grass can also be placed in the swath. To do this, fasten the deflector plates (1) in the marked bore holes and close the swath flaps (2).

AM-4-01312 2

Fig. 34

AM-97-02

2 1 2

Fig. 35


Maintenance

54

Pos: 27.1 /Überschriften/Überschriften 1/U-Z/Wartung @ 0\mod_1199883581050_78.docx @ 36685 @ 1 @ 1

10 Maintenance Pos: 27.2 /Überschriften/Überschriften 2/P-T/SSpezielle Sicherheitshinweise @ 0\mod_1196660495760_78.docx @ 9134 @ 2 @ 1

10.1 Special Safety Instructions Pos: 27.3 /BA/Sicherheit/6. Überarbeitete Warnhinweise/Warnung - Reparatur-,Wartungs- und Reinigungsarbeiten @ 299\mod_1412929917833_78.docx @ 2341058 @ @ 1

WARNING! When performing repair, maintenance or cleaning work on the machine, or in case of technical intervention, drive elements may start moving and thus there is a risk of injuries or death. • Switch off tractor engine, remove the ignition key and carry it with you. • Secure the tractor against accidental start-up and against rolling. • Wait until all machine parts have come to a complete stop and have been cooled down

completely. • Perform work on the disc mower only if it is in the working position.

Pos: 27.4 /BA/Sicherheit/7. Gefahrenhinweise alt/Mähwerke/Gefahr - Bei unregelmäßiger Kontrolle der Messerklingen und Haltebolzen @ 0\mod_1196782406281_78.docx @ 14870 @ @ 1

Danger! - When checking the cutter blades and retaining bolts only sporadically Effect: Danger to life, injuries or damage to the machine. • Always check the mowing units for damaged, missing or worn blades, retaining bolts, leaf

springs and cutting discs/blade drum before starting operation; replace any parts that are damaged, missing or worn!

• Always replace missing and damaged blades in sets to prevent unbalanced rotation! • Never mount unevenly worn blades on a drum/disc! • Whenever a blade is changed, also inspect the fasteners and replace them, if necessary!

Pos: 27.5 /Überschriften/Überschriften 3/P-T/PProbelauf @ 0\mod_1196833698843_78.docx @ 15023 @ 3 @ 1

10.1.1 Test run Pos: 27.6 /BA/Sicherheit/7. Gefahrenhinweise alt/Mähwerke/Gefahr - Probelauf Einzahl Mähwerk muss auf Boden aufliegen @ 11\mod_1223615241207_78.docx @ 148217 @ @ 1

Danger! - Testing the machine after repair, maintenance or cleaning work and after technical intervention. Effect: Danger to life or serious injuries • The mowing unit must be in working position • Do not switch on the drives until the mowing unit is resting on the ground and you are

absolutely sure that neither persons, animals nor objects are in the danger zone. • Start a trial run of the machine only from the driver’s seat.

Pos: 27.7 /Überschriften/Überschriften 2/A-E/EErsatzteile @ 0\mod_1196782991234_78.docx @ 14927 @ 2 @ 1

10.2 Spare Parts Pos: 27.8 /BA/Sicherheit/7. Gefahrenhinweise alt/Mähwerke/WARNUNG - Verwendung von nicht zugelassenen Ersatzteilen @ 308\mod_1417011577394_78.docx @ 2392925 @ @ 1

Warning! - Using non-approved spare parts. Effect: Danger to life, serious injuries or loss of warranty claims as well as exclusion of liability • Use only authentic KRONE spare parts and accessories authorised by the manufacturer.

The use of spare parts, accessories or additional equipment not manufactured, tested or approved by KRONE will exclude any liability for consequential damage.


Maintenance

55

Pos: 27.10.1 /Überschriften/Überschriften 2/A-E/AAnziehdrehmomente @ 202\mod_1385711894606_78.docx @ 1693123 @ 2 @ 1

10.3 Tightening torques Pos: 27.10.2 /Überschriften/Überschriften 3/K-O/Metrische Gewindeschrauben mit Regelgewinde @ 322\mod_1424945442462_78.docx @ 2483466 @ 3 @ 1

10.3.1 Metric Thread Screws with Control Thread Pos: 27.10.3 /BA/Wartung/Drehmomente / Anziehdrehmomente/Anziehdrehmomente Metrische Gewindeschrauben mit Regelgewinde Tabelle @ 321\mod_1424760222607_78.docx @ 2477725 @ @ 1

NOTICE

The table does not apply to countersunk screws with hexagonal socket in case the countersunk screw is tightened via hexagonal socket.

Tightening torque in Nm (unless otherwise stated)

A = thread size (stability class can be seen on screw head)

A

Stability class

5.6 8.8 10.9 12.9

Tightening torque (Nm)

M4 3.0 4.4 5.1

M5 5.9 8.7 10

M6 10 15 18

M8 25 36 43

M10 29 49 72 84

M12 42 85 125 145

M14 135 200 235

M16 210 310 365

M20 425 610 710

M22 571 832 972

M24 730 1050 1220

M27 1100 1550 1800

M30 1450 2100 2450


Maintenance

56

Pos: 27.10.5 /Überschriften/Überschriften 3/K-O/Metrische Gewindeschrauben mit Feingewinde @ 322\mod_1424945855944_78.docx @ 2484627 @ 3 @ 1

10.3.2 Metric Thread Screws with Fine Thread Pos: 27.10.6 /BA/Wartung/Drehmomente / Anziehdrehmomente/Anziehdrehmomente Metrische Gewindeschrauben mit Feingewinde Tabelle @ 321\mod_1424845229172_78.docx @ 2480186 @ @ 1



A

Stability class

5.6 8.8 10.9 12.9


M12 x 1.5:

88 130 152

M14 x 1.5 145 213 249

M16 x 1.5 222 327 382

M18 x 1.5 368 525 614

M20 x 1.5 465 662 775

M24 x 2 787 1121 1312

M27 x 2 1148 1635 1914

M30 x 1.5 800 2100 2650

Pos: 27.10.7 /Überschriften/Überschriften 3/K-O/Metrische Gewindeschrauben mit Senkkopf und Innensechskant @ 323\mod_1424945970760_78.docx @ 2484818 @ 3 @ 1

10.3.3 Metric Thread Screws with Countersunk Head and Hexagonal Socket Pos: 27.10.8 /BA/Wartung/Drehmomente / Anziehdrehmomente/Anziehdrehmomente Metrische Gewindeschrauben mit Senkkopf und Innensechskant Tabelle @ 321\mod_1424843938347_78.docx @ 2480155 @ @ 1

NOTICE

The table applies only to countersunk screws with hexagonal socket and metric thread which are tightened via hexagonal socket.



A

Stability class

5.6 8.8 10.9 12.9


M4 2.5 3.5 4.1

M5 4.7 7 8

M6 8 12 15

M8 20 29 35

M10 23 39 58 67

M12 34 68 100 116

M14 108 160 188

M16 168 248 292

M20 340 488 568

Pos: 27.11 /BA/Wartung/Muttern und Schrauben (50h) anziehen @ 0\mod_1196949864530_78.docx @ 15293 @ @ 1

Note Regularly check that nuts and bolts are tightly in place (approx. every 50 hours) and tighten them if necessary.


A

BM 400 0234

Maintenance

57

Pos: 27.13 /Überschriften/Überschriften 3/A-E/A/Abweichendes Drehmoment @ 0\mod_1196950054171_78.docx @ 15312 @ 3 @ 1

10.3.4 Deviating Torque Pos: 27.14 /BA/Wartung/Drehmomente / Anziehdrehmomente/Abweichendes Drehmoment AM-CV Baureihe @ 73\mod_1307600463856_78.docx @ 652563 @ @ 1

AM-5-066

1

2

3

Fig. 36

Screws / nuts MA [Nm]

Cutting disc screw (1) 49

Clamping pot screw (2) 215

Hexagonal nut of bearing housing (3) 42


Maintenance

58

Pos: 27.16 /Überschriften/Überschriften 2/F-J/FFüllmengen und Schmiermittelbezeichnungen der Getriebe @ 0\mod_1196951094046_78.docx @ 15335 @ 2 @ 1

10.4 Filling Quantities and Lubrication Designations for Gearboxes Pos: 27.17 /BA/Wartung/Tabellen_Füllmengen/Mähwerke/Technische Daten Betriebsstoffe Füllmengen AM-CV @ 73\mod_1307541707137_78.docx @ 652338 @ @ 1

Filling quantity

Refined oils Bio-degradable

lubricants

[litres] Brand name Brand name

Main gearbox 0.4 l

SAE 90 On request

Speed gearbox 1.5 l

Additional gearbox (1000-rpm PTO optional)

0.2 l

Cutter bar AM 203 CV 4.0 l

Cutter bar AM 243 CV (+B) 5.0 l

Cutter bar AM 283 CV (+B) 6.0 l

Pos: 27.18 /BA/Wartung/Zeitintervalle an den Getrieben 200 h @ 0\mod_1196951919921_78.docx @ 15373 @ 3 @ 1

10.4.1 Oil Level Check and Oil Change Intervals (Gearboxes)

Note - Oil level check and oil change (gearboxes) and lubricating the machine Effect: Long expected service life of machine • First oil change on all gearboxes after 50 operating hours, then every 200 operating hours

(but at least once a year). • Before using the machine always check the oil level. • With bio-degradable oils the changing intervals must be complied with absolutely because

of ageing of the oils.


Maintenance

59

Pos: 27.20.1 /Überschriften/Überschriften 2/F-J/HHauptgetriebe @ 0\mod_1197005740033_78.docx @ 15416 @ 2 @ 1

10.5 Main gearbox Pos: 27.20.2 /BA/Wartung/Ölkontrolle_Wechsel/Mähwerke/Bild Hauptgetriebe AM-S @ 69\mod_1305112110779_78.docx @ 634505 @ @ 1

Fig. 37 Pos: 27.20.3 /BA/Wartung/Ölkontrolle_Wechsel/Ölkontrolle_ALT/Ölkontrolle SAE 90 @ 0\mod_1197008973815_78.docx @ 15649 @ @ 1

Oil level check: • For time intervals, see Chapter "Oil Level Check and Oil Change Intervals (Gearboxes)". • Unscrew the inspection screw (1) • Oil level up to bore hole (1) • If necessary, top up the oil (SAE 90) • Screw the check screw (1) back in.

Pos: 27.20.4 /BA/Wartung/Ölkontrolle_Wechsel/Ölwechsel_ALT/Ölwechsel Version1 (Belüftungsfilter) @ 0\mod_1197010026283_78.docx @ 15747 @ @ 1

Oil change: • For time intervals, see Chapter "Oil Level Check and Oil Change Intervals (Gearboxes)". • Screw out the screw plug (2). • Collect the used oil in a suitable drip pan • Screw in the screw plug (2) • Fill oil (3) (oil level up to hole (1)) • Screw the inspection screw (1) and ventilation filter (3) back in.

Pos: 27.20.5 /BA/Wartung/Ölkontrolle_Wechsel/Ölqualität /Ölmenge: siehe Kapitel @ 0\mod_1197007859486_78.docx @ 15531 @ @ 1

Oil quality / oil quantity: see Chapter "Filling Quantities and Lubricant Designations for Gearboxes"

Pos: 27.20.6 /BA/Wartung/Ölkontrolle_Wechsel/Hinweis - Altöl ordnungsgemäß entsorgen @ 0\mod_1197008117002_78.docx @ 15550 @ @ 1

Note The used oil must be disposed of correctly


Maintenance

60

Pos: 27.22.1 /Überschriften/Überschriften 2/P-T/SSchaltgetriebe @ 0\mod_1197010889455_78.docx @ 15766 @ 2 @ 1

10.6 Speed gearbox Pos: 27.22.2 /BA/Wartung/Ölkontrolle_Wechsel/Mähwerke/Bild Schaltgetriebe AM-CV @ 73\mod_1307602773999_78.docx @ 652675 @ @ 1

AM-0-033A B

1

2

Fig. 38 Pos: 27.22.3 /BA/Wartung/Ölkontrolle_Wechsel/Ölkontrolle_ALT/Ölkontrolle SAE 90 @ 0\mod_1197008973815_78.docx @ 15649 @ @ 1

Oil level check: • For time intervals, see Chapter "Oil Level Check and Oil Change Intervals (Gearboxes)". • Unscrew the inspection screw (1) • Oil level up to bore hole (1) • If necessary, top up the oil (SAE 90) • Screw the check screw (1) back in.

Pos: 27.22.4 /BA/Wartung/Ölkontrolle_Wechsel/Ölwechsel_ALT/Ölwechsel Version2 @ 0\mod_1197016258486_78.docx @ 15884 @ @ 1

Oil change: • For time intervals, see Chapter "Oil Level Check and Oil Change Intervals (Gearboxes)". • Screw out the screw plug (2). • Collect the used oil in a suitable drip pan • Screw in the screw plug (2) • Fill oil (1) (oil level up to hole (1))

Pos: 27.22.5 /BA/Wartung/Ölkontrolle_Wechsel/Ölqualität /Ölmenge: siehe Kapitel @ 0\mod_1197007859486_78.docx @ 15531 @ @ 1

Oil quality / oil quantity: see Chapter "Filling Quantities and Lubricant Designations for Gearboxes"

Pos: 27.22.6 /BA/Wartung/Ölkontrolle_Wechsel/Hinweis - Altöl ordnungsgemäß entsorgen @ 0\mod_1197008117002_78.docx @ 15550 @ @ 1

Note The used oil must be disposed of correctly


Maintenance

61

Pos: 27.24.1 /Überschriften/Überschriften 2/K-O/OÖlstandskontrolle und Ölwechsel am Mähholm @ 0\mod_1197017549815_78.docx @ 15963 @ 2 @ 1

10.7 Oil level check and oil change on the cutter bar Pos: 27.24.2 /Überschriften/Überschriften 3/K-O/Ölwechsel @ 0\mod_1197021941955_78.docx @ 16139 @ 3 @ 1

10.7.1 Oil change Pos: 27.24.3 /BA/Wartung/Mähwerke/Hinweis Ein Ölwechsel am Mähholm ist nicht erforderlich. @ 68\mod_1304577391388_78.docx @ 628708 @ @ 1

Note No oil change is required on the cutter bar.

Pos: 27.24.4 /Überschriften/Überschriften 3/K-O/Ölkontrolle @ 0\mod_1197021908190_78.docx @ 16120 @ 3 @ 1

10.7.2 Checking the oil level Pos: 27.24.5 /BA/Sicherheit/7. Gefahrenhinweise alt/Mähwerke/Gefahr - Schnell rotierende Messerteller/Messertrommel_2 @ 0\mod_1197022569252_78.docx @ 16165 @ @ 1

Danger! - Rapidly rotating cutting discs/blade drums. Effect: Danger to life or serious injuries. Lower guards. Nobody should be in the danger zone around the machine.

Pos: 27.24.6 /BA/Wartung/Mähwerke/AM Baureihe/Vorbereitung Ölkontrolle / Ölwechel AM-CV Baureihe @ 73\mod_1307600994214_78.docx @ 652619 @ @ 1

• Allow the machine to run briefly • Turn off the PTO • Wait until cutting discs/blade drums have come to a complete stop • Move the cutter bar into transport position

CAUTION! Make absolutely certain that the transport interlock is engaged in transport position.

• Switch off the tractor engine and remove the ignition key • Close the shut-off valve on the hydraulic hose of the disc mower

Pos: 27.24.7 /BA/Wartung/Mähwerke/Ölkontrolle / Ölwechsel Mähholm AM-CV Baureihe Bild @ 70\mod_1305117028232_78.docx @ 634812 @ @ 1

Fig. 39 Pos: 27.24.8 /BA/Wartung/Mähwerke/Ölkontrolle Mähholm AM-S / AM-CV Baureihe @ 70\mod_1305115617542_78.docx @ 634784 @ @ 1

Check the oil level before every use • Remove the oil level inspection screw (1) from the cutter bar • The oil level must be up to the bore hole. If necessary, top up the oil (SAE 90) • Screw in the oil level inspection screw (1) again and tighten securely


Maintenance

62

Pos: 27.26 /Überschriften/Überschriften 2/P-T/SSchutztücher @ 70\mod_1305118877599_78.docx @ 634957 @ 2 @ 1

10.8 Guard Cloths Pos: 27.27 /BA/Sicherheit/7. Gefahrenhinweise alt/Gefahr - Fehlende Schutztücher / Schutztücher schützen @ 73\mod_1307606084485_78.docx @ 652870 @ @ 1

Danger! - Missing or damaged guard cloths Effect: Danger to life, serious injuries or serious damage to the machine. The protective equipment on the machine, e.g. guard cloths and hoods, protects against flying stones and similar objects and also prevents access to dangerous parts. • Damaged or worn guard cloths must be replaced without delay • Use only original cloths • Move the guard cloths into position prior to starting work

Pos: 27.28 /BA/Wartung/Mähwerke/AM Baureihe/Schutztücher AM-CV Bild @ 73\mod_1307605183383_78.docx @ 652842 @ @ 1

AM-1-076

Fig. 40 Pos: 27.29 /BA/Wartung/Mähwerke/AM Baureihe/Hinweis Der Schutzrahmen und die Schutztücher schützen vor hochgeschleuderten Gegenständen @ 70\mod_1305119565233_78.docx @ 635061 @ @ 1

Note The protective frame and guard cloths protect against objects that would be forcibly ejected upward. They also prevent contact with rotating blades.

Pos: 27.30 /BA/Wartung/Mähwerke/AM Baureihe/Die Schutztücher regelmäßig überprüfen @ 70\mod_1305119723635_78.docx @ 635088 @ @ 1

Check the guard cloths regularly. Replace worn or damaged guard cloths immediately. Pos: 27.31 /Layout Module /---------------Seitenumbruch---------------- @ 0\mod_1196175311226_0.docx @ 4165 @ @ 1

Maintenance

63

Pos: 27.32 /Überschriften/Überschriften 2/U-Z/ZZetter @ 73\mod_1307606866684_78.docx @ 652898 @ 2 @ 1

10.9 Tedder Pos: 27.33 /BA/Einstellungen/Mähwerke/Einstellung Zetterwalze AM-CV Bild @ 73\mod_1307607084046_78.docx @ 652925 @ @ 1

AM-1-089

21

Fig. 41 Pos: 27.34 /BA/Einstellungen/Mähwerke/Kontrolle der Zetterwalze @ 0\mod_1196671110947_78.docx @ 10456 @ @ 1

Note - Checking the conditioner auger Effect: Longer service life • Before putting into operation, always check the conditioner roller (1) for damaged V-tines (2).• Straighten any bent tines. • Replace any broken tines. • Check the bearing bolts and bushes on the prong bearings. To prevent the loss of prongs,

always replace bearing bolts and bushes in good time.

Pos: 27.35 /BA/Wartung/Mähwerke/AM Baureihe/Wartung Pfahlsicherung AM-S @ 70\mod_1305121132918_78.docx @ 635175 @ 2 @ 1

10.10 Maintenance of pole protection

Fig. 42 The pole protection (1) must be maintained at least once a year. To perform maintenance, release the tension on the spring (2) and remove it. Then pull the pole protection (1) apart and clean the contact surfaces of both inclined bevels. Then grease the inclined bevels and mount the pole protection.

Note For the triggering moment setting, see "Pole Protection Setting" in the Settings chapter


Maintenance

64

Pos: 27.37.1 /Überschriften/Überschriften 2/K-O/KKontrolle der Mähklingen und Messerhalterung @ 0\mod_1197265641329_78.docx @ 16323 @ 2 @ 1

10.11 Checking the Cutter Blades and Blade Holder Pos: 27.37.2 /BA/Sicherheit/7. Gefahrenhinweise alt/Mähwerke/Gefahr - Fehlende und beschädigte Mähklingen und Mähklingenhalterungen @ 0\mod_1197265722813_78.docx @ 16342 @ @ 1

Warning! - Missing and damaged cutter blades and cutter blade retainers. Effect: Danger to life, serious injuries or damage to the machine • Check cutter blades at least once per day and check retaining bolts every time you change

the blades or after contact with foreign objects. • Immediately replace missing or damaged cutter blades and cutter blade retainers

Pos: 27.37.3 /BA/Wartung/Mähwerke/Schutzvorrichtung hochklappen/runterklappen Bild AM-CV Baureihe @ 73\mod_1308549011118_78.docx @ 655617 @ @ 1

AM-0-090

Fig. 43 Pos: 27.37.4 /BA/Wartung/Mähwerke/Schutzvorrichtung hochklappen/runterklappen AM Baureihe @ 70\mod_1305177031755_78.docx @ 635507 @ @ 1

To check and fit the blades, fold up the protective device (1). Now you can access the blades (2).

Note After the inspection and installation tasks are completed, move the protective device into its protective position.


Maintenance

65

Pos: 27.37.6 /Überschriften/Überschriften 3/K-O/Mähklingen @ 0\mod_1197265959110_78.docx @ 16361 @ 3 @ 1

10.11.1 Cutter Blades Pos: 27.37.7 /BA/Wartung/Mähwerke/Die Bohrung der Mähklingen kann sich durch Verschleiß aufweiten. @ 10\mod_1221048982715_78.docx @ 131675 @ @ 1

The borehole on the cutter blades may spread due to wear.

Pos: 27.37.8 /BA/Sicherheit/7. Gefahrenhinweise alt/MähwerkeWarnung - Zu geringe Materialstärke an den Mähklingen_neu @ 312\mod_1418983956660_78.docx @ 2409555 @ @ 1

Danger! - Insufficient thickness of material on the cutter blades. Effect: Danger to life or serious injuries. • The cutter blades must be replaced at the latest when the wear limit is reached (see mark

(1) on the cutter blade; dimension a less than or equal to 13 mm).

Pos: 27.37.9 /BA/Wartung/Mähwerke/Mähklingen beidseitig verwenbar_neu @ 3\mod_1204728012601_78.docx @ 72608 @ @ 1

a

EC 253 01

Fig. 44

Note - The cutter blades can be turned around and used on both sides. • When cutter blades are missing or damaged, they must be replaced as a complete set.

This prevents dangerous unbalanced rotation


Maintenance

66

Pos: 27.37.11 /BA/Wartung/Mähwerke/Messerschraub / Messerschnellverschluss/Messerschraubverschluss Haltebolzen 12 mm AM @ 70\mod_1305177453579_78.docx @ 635533 @ 3 @ 1

10.11.2 Blade Screw Connection

DANGER! - Insufficient thickness of material on the retaining bolts. Effect: Danger to life or serious injuries. • Every time a blade is changed, check the thickness of the holding bolts material. • Damage or worn retaining bolts must always be replaced by sets on each cutting

disc/blade drum! • The material thickness of the retaining bolts must not be less than 12 mm at the weakest

point.

Fig. 45

Pos: 27.37.12 /BA/Wartung/Mähwerke/Messerschraub / Messerschnellverschluss/Messerschnellverschluss Haltebolzen 9mm AM @ 70\mod_1305178072510_78.docx @ 635701 @ 3 @ 1

10.11.3 Blade Quick-Fit Device

DANGER! – Insufficient thickness of material on the retaining bolts. Effect: Danger to life or serious injuries. • Every time a blade is changed, check the thickness of the holding bolts material. • Damage or worn retaining bolts must always be replaced by sets on each cutting disc/blade

drum! • The material thickness of the retaining bolts must not be less than 9 mm at the weakest

point. • The material thickness of the leaf spring must not be less than 3 mm at the weakest point.

Fig. 46


Maintenance

67

Pos: 27.37.14 /Überschriften/Überschriften 2/K-O/MMesserwechsel an Messertellern @ 0\mod_1197269068562_78.docx @ 16521 @ 2 @ 1

10.12 Blade Changing on Cutting Discs Pos: 27.37.15 /BA/Sicherheit/7. Gefahrenhinweise alt/Mähwerke/Gefahr - Schnell rotierende Messerteller/Messertrommeln_1 @ 0\mod_1197017696736_78.docx @ 16001 @ @ 1

Danger! - Rapidly rotating cutting discs/blade drums. Effect: Danger to life or serious injuries. • Switch off the engine and remove the ignition key. • The cutting discs/blade drums continue to run! • Do not leave the driver’s cab until the cutting discs/blade drums have come to a complete

stop.

Pos: 27.37.16 /BA/Sicherheit/7. Gefahrenhinweise alt/Mähwerke/Gefahr - Sich lösende Mähklingen @ 0\mod_1197269483265_78.docx @ 16540 @ @ 1

Danger! - Cutter blades coming loose Effect: Danger to life or serious injuries. • After changing the blades check that they fit perfectly and that they can move freely. • Whenever a blade is changed, also inspect the fasteners and replace them, if necessary! • Always replace missing and damaged blades in sets to prevent unbalanced rotation! • Never mount unevenly worn blades on a drum/disc!

Pos: 27.37.17 /BA/Wartung/Mähwerke/Spezialwerkzeug Messerschnellverschluss @ 73\mod_1307609905027_78.docx @ 653035 @ 2 @ 1

10.13 Special Tool

Fig. 47 The special tool (1) {blade wrench for blade quick-fit device} or the offset ring spanner (2) {for blade screw connection} are included in the scope of delivery. The tool (1 or 2) is located on the holder (3) on the rear hinge pipe (4) of the three-point block. After the tool has been used, insert it in the holder (3) again and secure it with the linch pin (5).


Maintenance

68

Pos: 27.37.19 /Überschriften/Überschriften 3/K-O/Messerschraubverschluss @ 0\mod_1197270941296_78.docx @ 16578 @ 3 @ 1

10.13.1 Blade Screw Connection Pos: 27.37.20 /BA/Wartung/Mähwerke/Messerschraub / Messerschnellverschluss/Beschreibung Messerwechsel Messerschraubverschluss AM @ 70\mod_1305178894100_78.docx @ 635757 @ @ 1

AM-4-032

23

4

1

5

4

1

25

Fig. 48 • Fold up the protective device • Clean the area • Remove damaged or worn blades • To fit a blade (5), insert it between the wear plate (2) and the cutting disc (1) • Insert the retaining bolt (3) from below through the wear plate, the blade and the cutting disc • Place the hex nut (4) on the bolt from above and tighten it firmly (for torque see section

"Torques"). • Repeat this process for all blades, including those on the blade drums • After fitting the blades, fold the protective device down again

Pos: 27.37.21 /BA/Wartung/Mähwerke/Messerschraub / Messerschnellverschluss/Beschreibung Messerwechsel Messerschraubverschluss Hinweis @ 71\mod_1306221707374_78.docx @ 644013 @ @ 1

Note • The cutter blades of anticlockwise rotating cutting discs / blade drums are different to those

of clockwise rotating ones. Make certain the direction of rotation is correct when installing! • The arrow on the cutter blades must match the direction of rotation of the corresponding

cutting discs / blade drums • The locknut (4) used to secure the retaining bolts must not be used more than once

Pos: 27.37.22 /BA/Wartung/Mähwerke/Messerschraub / Messerschnellverschluss/Beschreibung Messerwechsel Best.-Nr. @ 72\mod_1306221763858_78.docx @ 644041 @ @ 1

Order No. for clockwise rotating blade: 139-889 Order No. for anticlockwise rotating blade: 139-888

Pos: 27.37.23 /BA/Wartung/Mähwerke/Messerschraub / Messerschnellverschluss/Beschreibung Messerwechsel alternativ Best.-Nr. @ 72\mod_1306223454041_78.docx @ 644097 @ @ 1

Alternatively: Order No. for roof-shaped blade (clockwise and anticlockwise threading): 139 800


Maintenance

69

Pos: 27.37.25 /Überschriften/Überschriften 3/K-O/Messerschnellverschluss @ 0\mod_1197271019859_78.docx @ 16597 @ 3 @ 1

10.13.2 Blade Quick-Fit Device Pos: 27.37.26 /BA/Wartung/Mähwerke/Messerschraub / Messerschnellverschluss/Beschreibung Messerwechsel Messerschnellverschluss AM @ 70\mod_1305179210423_78.docx @ 635785 @ @ 1

Fig. 49 • Fold up the protective device • Clean the area • Remove damaged or worn blades • Push the special tool (1) (blade key) between the cutter disc (4) and leaf spring (3) and

press down with one hand • Guide a new blade (2) onto the retaining bolt and allow the blade key to return upwards • Repeat this process for all blades, including those on the blade drums • After fitting the blades, fold the protective device down again

Pos: 27.37.27 /BA/Wartung/Mähwerke/Messerschraub / Messerschnellverschluss/Beschreibung Messerwechsel Messerschnellverschluss Hinweis @ 72\mod_1306223027118_78.docx @ 644069 @ @ 1

Note • The cutter blades of anticlockwise rotating cutting discs / blade drums are different to those

of clockwise rotating ones. Make certain the direction of rotation is correct when installing! • The arrow on the cutter blades must match the direction of rotation of the corresponding

cutting discs / blade drums

Pos: 27.37.28 /BA/Wartung/Mähwerke/Messerschraub / Messerschnellverschluss/Beschreibung Messerwechsel Best.-Nr. @ 72\mod_1306221763858_78.docx @ 644041 @ @ 1

Order No. for clockwise rotating blade: 139-889 Order No. for anticlockwise rotating blade: 139-888

Pos: 27.37.29 /BA/Wartung/Mähwerke/Messerschraub / Messerschnellverschluss/Beschreibung Messerwechsel alternativ Best.-Nr. @ 72\mod_1306223454041_78.docx @ 644097 @ @ 1

Alternatively: Order No. for roof-shaped blade (clockwise and anticlockwise threading): 139 800


Maintenance

70

Pos: 27.37.31 /BA/Wartung/Mähwerke/Stoßkanten erneuern AM @ 70\mod_1305180043738_78.docx @ 635841 @ 2 @ 1

10.14 Replacing the Linings

Caution! – Linings not checked Effect: Damage to the machine • Always check the mowing unit for damaged linings prior to start-up and replace linings, if

necessary! • Adjust the welding current and the welding material to the cutter bar material and to the

lining or carry out a trial welding if necessary.

ART.NR. 150-039

MH-0-001

Fig. 50


Maintenance – lubrication chart

71

Pos: 27.39.1 /Überschriften/Überschriften 1/U-Z/Wartung - Schmierplan @ 0\mod_1197359304198_78.docx @ 18232 @ 1 @ 1

11 Maintenance – lubrication chart Pos: 27.39.2 /Überschriften/Überschriften 2/P-T/SSpezielle Sicherheitshinweise @ 0\mod_1196660495760_78.docx @ 9134 @ 2 @ 1

11.1 Special Safety Instructions Pos: 27.39.3 /BA/Sicherheit/7. Gefahrenhinweise alt/Mähwerke/Warnung - Reparatur_Wartung_Reinigungs_4 allgemein EasyCut @ 292\mod_1410941423112_78.docx @ 2299026 @ @ 1

WARNING! When performing repair, maintenance or cleaning work or in case of technical intervention, drive elements may start moving (caution: cutting discs continue to run). Effect: Danger to life, injuries or damage to the machine. • Turn off the PTO shaft. • Move the machine to the working position and lower it to the ground. • Switch off the engine of the tractor, remove the ignition key and carry it with you. • Secure the tractor against accidental start-up and against rolling. • After the repair, maintenance, cleaning work or technical modifications are completed,

mount all protective covers and safety devices properly again. • Avoid skin contact with oils, greases, cleaning agents and solvents. • In the event of injuries or burns due to oils, cleaning agents or solvents, contact a physician

immediately. • All other safety instructions must also be followed to avoid injuries and accidents.

Pos: 27.39.4 /Überschriften/Überschriften 2/F-J/GGelenkwelle @ 0\mod_1199781879794_78.docx @ 34542 @ 2 @ 1

11.2 PTO shaft Pos: 27.39.5 /BA/Wartung/Gelenkwelle schmieren/Abschmieren Gelenkwelle AM @ 70\mod_1305181059201_78.docx @ 635935 @ @ 1

AMS-1-048

Fig. 51 Lubricate the PTO shafts at the intervals indicated in the drawing with a multi-purpose grease. Follow the operating instructions of the PTO shaft manufacturer.


Maintenance – lubrication chart

72

Pos: 27.39.7 /Überschriften/Überschriften 2/P-T/SSchmierplan @ 0\mod_1197361829026_78.docx @ 18495 @ 2 @ 1

11.3 Lubrication Chart Pos: 27.39.8 /BA/Wartung/Mähwerke/EasyCut / AM Mähwerke/Schmierpläne/Schmierplan AM-CV @ 73\mod_1307629636426_78.docx @ 654808 @ @ 1

AM-1-077-2

10 h 10 h 10 h

50 h

10 h

50 h

Fig. 52 Pos: 28 /Layout Module /---------------Seitenumbruch---------------- @ 0\mod_1196175311226_0.docx @ 4165 @ @ 1

Placing in Storage

73

Pos: 29.1 /Überschriften/Überschriften 1/A-E/Einlagerung @ 0\mod_1197385459120_78.docx @ 19966 @ 1 @ 1

12 Placing in Storage Pos: 29.2.1 /BA/Einlagerung/Maschine an einem trockenem Ort abstellen @ 70\mod_1305630069850_78.docx @ 638292 @ @ 1

• Park the machine in a dry location, but not in the vicinity of artificial fertilisers or livestock buildings.

Pos: 29.2.2 /BA/Einlagerung/Vor der Einwinterung die Maschine innen und außen gründlich reinigen @ 70\mod_1305635346852_78.docx @ 638460 @ @ 1

• Before placing the machine in winter storage, clean inside and outside thoroughly. If you use a high-pressure cleaner to do this. do not keep a stream of water directed at bearing points. After cleaning is completed, lubricate all lubrication points. Do not wipe off any grease that comes out of bearing points. The hardened grease will provide additional protection against moisture.

Pos: 29.2.3 /BA/Einlagerung/Gelenkwelle auseinanderziehen und einfetten @ 70\mod_1305631424563_78.docx @ 638348 @ @ 1

• Disassemble the PTO shaft. Lubricate the inner tubes and the guard tube with grease. Grease the lubrication points on the cross joint and on the bearing rings of the guard tubes.

Pos: 29.2.4 /BA/Einlagerung/Alle Gelenkstellen einölen @ 70\mod_1305633347429_78.docx @ 638432 @ @ 1

• Oil all joint points! Pos: 29.2.5 /BA/Einlagerung/Lackschäden ausbessern, blanke Stellen gründlich mit Rostschutzmittel konservieren @ 70\mod_1305630900253_78.docx @ 638320 @ @ 1

• Touch up damaged paint and preserve all uncoated areas thoroughly with rust protection agent.

Pos: 29.2.6 /BA/Einlagerung/Alle beweglichen Bauteile überprüfen @ 70\mod_1305632768685_78.docx @ 638404 @ @ 1

• Check all movable components such as deflector rollers, joints, tension rollers, etc. to make certain they move easily. If necessary remove, clean, grease and remount. If necessary, replace with new parts.

Pos: 29.2.7 /BA/Einlagerung/Reibkupplung/Reibkupplung stillegen @ 70\mod_1305636454606_78.docx @ 638543 @ @ 1

• Shut down the overload coupling Pos: 29.2.8 /BA/Einlagerung/Verwenden Sie nur Original-KRONE-Ersatzteile @ 70\mod_1305632212285_78.docx @ 638376 @ @ 1

• Use only original KRONE replacement parts. Pos: 29.2.9 /BA/Einlagerung/Sammelliste erstellen @ 70\mod_1305626681125_78.docx @ 638264 @ @ 1

Perform the necessary repair tasks during the time immediately after the harvest season. Draw up a list of all replacement parts you will need. This will make it easier for your KRONE dealer to process your orders and you will be certain that your machine will be ready for use at the beginning of the next season.


Before the Start of the New Season

74

Pos: 29.4 /Überschriften/Überschriften 1/U-Z/Vor Beginn der neuen Saison @ 4\mod_1211272647559_78.docx @ 82867 @ 1 @ 1

13 Before the Start of the New Season Pos: 29.5 /Überschriften/Überschriften 2/P-T/SSpezielle Sicherheitshinweise @ 0\mod_1196660495760_78.docx @ 9134 @ 2 @ 1

13.1 Special Safety Instructions Pos: 29.6 /BA/Sicherheit/7. Gefahrenhinweise alt/Mähwerke/Warnung - Reparatur_Wartung_Reinigungs_4 allgemein EasyCut @ 292\mod_1410941423112_78.docx @ 2299026 @ @ 1




Pos: 29.7 /Überschriften/Überschriften 2/P-T/PProbelauf @ 0\mod_1196782963921_78.docx @ 14908 @ 2 @ 1

13.2 Test run. Pos: 29.8 /BA/Sicherheit/7. Gefahrenhinweise alt/Mähwerke/Gefahr - Probelauf Einzahl Mähwerk muss auf Boden aufliegen @ 11\mod_1223615241207_78.docx @ 148217 @ @ 1

Danger! - Testing the machine after repair, maintenance or cleaning work and after technical intervention. Effect: Danger to life or serious injuries • The mowing unit must be in working position • Do not switch on the drives until the mowing unit is resting on the ground and you are

absolutely sure that neither persons, animals nor objects are in the danger zone. • Start a trial run of the machine only from the driver’s seat.



75

Pos: 29.10 /BA/Einlagerung/EasyCut / AM Mähwerke/Die zur Konservierung verwendeten Fette und Öle abwischen @ 73\mod_1307607607042_78.docx @ 652953 @ @ 1

• Wipe off the grease and oil used for preservation Pos: 29.11 /BA/Einlagerung/EasyCut / AM Mähwerke/Vor der Saison ohne Bereifung @ 3\mod_1204731533226_78.docx @ 72767 @ @ 1

• Lubricate the machine thoroughly. Remove any condensation water which may have collected in the bearings.

• Check oil level in the gearbox(es) and top up if necessary. • Check all screws to make certain they are tight or retighten them if necessary. • Check all electrical connection cables and the lighting. Repair or replace if necessary. • Check the entire setting of the machine and correct if necessary. • Re-read the operating instructions thoroughly.

Note Use vegetable oils and greases.

Pos: 29.12 /BA/Einlagerung/Reibkupplung/Reibkupplung lüften vor der Saison @ 3\mod_1204731645242_78.docx @ 72787 @ @ 1

• Vent the friction clutch to release the adhesion of the friction lining. Pos: 29.13 /Layout Module /---------------Seitenumbruch---------------- @ 0\mod_1196175311226_0.docx @ 4165 @ @ 1


76

Pos: 29.14 /Überschriften/Überschriften 2/P-T/RReibkupplung @ 3\mod_1204782451808_78.docx @ 72905 @ 2 @ 1

13.3 Friction Clutch Pos: 29.15 /BA/Sicherheit/Reibkupplung/Achtung - Manipulation an der Reibkupplung @ 3\mod_1204732138258_78.docx @ 72825 @ @ 1

Caution! - Manipulation of the friction clutch Effect: Serious damage to the machine • Manipulation of the overload protection changes the slip torque. This will lead to a loss of

warranty claims! Original KRONE spare parts only may be used.

Pos: 29.16 /BA/Einlagerung/Reibkupplung/Hinweis Reibkupplung freidrehen bei angebautem Mähwerk AM_S @ 70\mod_1305539282870_78.docx @ 637044 @ @ 1

Note To place the machine in service again, attach it to the tractor and switch on the PTO shaft. When the overload coupling is vented, the cutting discs should not be turning with it. If the cutting discs do turn, it is because the overload coupling is jammed or rusted and stiff, in which case it must be disassembled. (Loosen the friction lining from the plates. If necessary smooth the friction surfaces with emery paper.) Then attach the PTO shaft again and proceed as described in section "Walterscheid Overload Coupling“.

Pos: 29.17 /BA/Inbetriebnahme/EasyCut/Hinweis Reibkupplung @ 11\mod_1223358975938_78.docx @ 145593 @ @ 1

Note - Friction Clutch Effect: Conserve functionality and increased service life • The friction clutch (2) must be vented prior to commissioning and once a year prior to

harvesting. (See section Before the Start of the New Season "Friction clutch")

Pos: 29.18 /Überschriften/Überschriften 2/P-T/RReibkupplung - Walterscheid @ 70\mod_1305539865257_78.docx @ 637138 @ 2 @ 1

13.4 Walterscheid Overload Coupling Pos: 29.19 /BA/Einlagerung/Reibkupplung/Reibkupplung entlüften @ 3\mod_1204732297351_78.docx @ 72885 @ @ 1

EC-257-012

Fig. 53 The friction clutch protects the tractor and the machine against damage. It is designed with a permanently adjusted turning torque MR. The torque is applied on the housing of the friction clutch (2). Venting the friction clutch Tighten the four nuts (1). Block the machine and move the friction clutch manually to the point where it slips through. Loosen the nuts again.



77

Pos: 29.21 /BA/Einlagerung/Reibkupplung/Lüften der Reibkupplung an der Antriebswelle zum Mähholm @ 70\mod_1305539924943_78.docx @ 637166 @ 3 @ 1

13.4.1 Venting the Overload Coupling on the Drive Shaft to the Cutter Bar

Pos: 29.22 /BA/Einlagerung/Reibkupplung/Reibkupplung Antriebswelle Mähholm Bild AM-S @ 70\mod_1305552829950_78.docx @ 637497 @ @ 1

Fig. 54 Pos: 29.23 /BA/Einlagerung/Reibkupplung/Achtung Das Lüften der Reibkupplung am Mähholmantrieb kann nur in Transportstellung des Scheibenmähe @ 70\mod_1305540007049_78.docx @ 637223 @ @ 1

CAUTION! The overload coupling on the cutter bar drive can only be vented in the transport position of the disc mower. The cutter bar must be secured by a transport brace.

Pos: 29.24 /BA/Einlagerung/Reibkupplung/Reibkupplung lüften Reibkupplung an der Antriebswelle zum Mähholm @ 70\mod_1305540715787_78.docx @ 637470 @ @ 1

The overload coupling must be vented when it has not been used for a long time (for example before the beginning of harvest). To do this: • Tighten the nuts (1) on the overload coupling (2) of the cutter bar drive • Tighten the PTO shaft • Turn the blade drum in any direction by hand (turning the drum loosens the discs in the

overload coupling from each other) • Loosen the nuts again after this process until there is a free space of at least 3 mm between

the nut and the housing Pos: 30 /Layout Module /---------------Seitenumbruch---------------- @ 0\mod_1196175311226_0.docx @ 4165 @ @ 1

Special equipment

78

Pos: 31.1 /Überschriften/Überschriften 1/P-T/Sonderausstattung @ 2\mod_1202808469779_78.docx @ 61649 @ 1 @ 1

14 Special equipment Pos: 31.2 /Überschriften/Überschriften 2/P-T/SSpezielle Sicherheitshinweise @ 0\mod_1196660495760_78.docx @ 9134 @ 2 @ 1

14.1 Special Safety Instructions Pos: 31.3 /BA/Sicherheit/7. Gefahrenhinweise alt/Mähwerke/Warnung - Reparatur_Wartung_Reinigungs_4 allgemein EasyCut @ 292\mod_1410941423112_78.docx @ 2299026 @ @ 1




Pos: 31.4 /Überschriften/Überschriften 2/F-J/HHochschnittkufen @ 70\mod_1305639862319_78.docx @ 638598 @ 2 @ 1

14.2 Adjusting Skids Pos: 31.5 /BA/Sonderausstatung/Gefahr Maschine sinkt unkontrolliert ab @ 70\mod_1305639968799_78.docx @ 638625 @ @ 1

DANGER! – Machine drops without control Danger to life or serious injuries. • Never walk under a raised machine • Support the raised machine safely

Pos: 31.6 /BA/Sonderausstatung/EasyCut / AM Mähwerke/Hochschnittkufen AM-Mähwerke @ 70\mod_1305555023464_78.docx @ 637582 @ @ 1

1

3

2

AMT-M-003

4

Fig. 55 Adjusting skids can be used to adjust the cutting height in two stages (see section entitled "Adjusting the Cutting Height") To do this screw on the bar (4) under the cutter bar (1). Then insert the adjusting skid (3) into the glide skid (2) and screw together with the bar at the required height (4). The adjusting skids must always be mounted underneath the cutting discs that run next to the mower drums.


Appendix - Assembly Instructions

79

Pos: 33.1 /Überschriften/Überschriften 1/A-E/Anhang Zusammenbau-Anleitung @ 73\mod_1307683902824_78.docx @ 654845 @ 1 @ 1

15 Appendix - Assembly Instructions Pos: 33.2 /BA/Sicherheit/7. Gefahrenhinweise alt/Gefahr - Fehlerhafter Zusammenbau @ 1\mod_1202224212591_78.docx @ 58171 @ @ 1

Danger! - Incorrect assembly Effect: Danger to life, serious injuries or serious damage to the machine. • Only authorised service centres may assemble the machine. • The machine must be assembled with special care. • Always heed the applicable accident prevention regulations. • Use only safe and sufficiently dimensioned lifting equipment and load-securing equipment. • The machine may be taken into operation only after all the safety devices have been

installed. • If unauthorised modifications are made to the machine, the manufacturer is released from

liability for any resulting damage.

Pos: 33.3 /BA/Anhang/AM Mähwerke/Zusammenbau-Anleitung/Zusammenbau-Anleitung @ 73\mod_1307611300831_78.docx @ 653063 @ @ 1

The following pages describe the first installation (assembly) of the Krone machine. When assembling the machine, follow the specified order of the installation steps as they are listed! Operation of the machine is described in the corresponding operating instructions.

Pos: 33.4 /Zusammenbau-Anleitungen/AM Mähwerke/AM-CV Baureihe/AM-4-000-1 Inhalt Kiste @ 73\mod_1307611638594_0.docx @ 653114 @ @ 1


80

4

27

8

7 13

2/3

30

6

1

26

5

28

34

24

11

32

33

109

2019

18

39

16 15

14

23

31

22

36

21

38

37

12

29

3517

1

AM-4-000

40

Pos: 33.5 /Zusammenbau-Anleitungen/AM Mähwerke/AM-CV Baureihe/Schraubenbeutel_AM-CV @ 73\mod_1307621695288_0.docx @ 654743 @ @ 1


81

Anzahl Typ Pos. Teile-Nr. Maße

1 50 916 096 * Ø20 x 110

- 51 Ø20 x 95

- 52 916 082 * Ø20 x 45

- 53 901 155 * M16 x 240

2 54 900 674 * M16 x 35

- 55 901 162 * M14 x 70

- 56 901 122 * M12 x 70

2 57 900 632 * M10 x 16

- 58 M8 x 110

3 59 901 425 * M8 x 60

2 60 904 882 * M12 x 25

6 AM 203 CV

61 904 751 * M10 x 20 7 AM 243 CV

9 AM 283 CV

2 62 904 732 * M8 x 25

2 63 904 730 * M8 x 16

6 AM 203 CV

64 904 710 * M6 x 16 7 AM 243 CV

9 AM 283 CV

2 65 908 716 * M16

6 AM 203 CV

66 908 758 * M10 7 AM 243 CV

9 AM 283 CV

7 67 908 706 * NM8

6 AM 203 CV

68 908 704 * M6 7 AM 243 CV

9 AM 283 CV

2 69 909 503 * M12

- 70 13 x 85

- 71 5 x 40

- 72 139 567 * Ro. 26,9/2,65x191

2 73 910 512 * 21 x 37 x 3

2 74 910 303 * 17 x 30 x 3

2 75 910 347 * 17 x 37 x 3 PE

6 AM 203 CV

76 910 609 * 13 x 37 x 3 7 AM 243 CV

9 AM 283 CV

2 77 910 353 * 11 x 34 x 3

5 78 909 908 * SKM 8

6 AM 203 CV

79 909 906 * SKM 6 7 AM 243 CV

9 AM 283 CV

1 80 917 007 * 7,5 x 42

1 81 150 032 * 20 x 185

2 82 912 670 * 8 x 40

8 84 910 363 * 15x36x6

2 85 909 909 * 10x 22x 6

4 86 908 714 * M 14

1 87 919 106 * M 8 x 1

2 88 919 105 * M 8 x 1

Pos: 33.6 /Zusammenbau-Anleitungen/AM Mähwerke/AM-CV Baureihe/AM-4-005 @ 73\mod_1307613373224_0.docx @ 653521 @ @ 1


82

AM-4-005

g

d

hb

a

c

e

i

fda

Pos: 33.7 /Zusammenbau-Anleitungen/AM Mähwerke/AM-CV Baureihe/AM-2-004 / AM-3-006 / AM-3-007 / AM-3-008 @ 73\mod_1307613460376_0.docx @ 653549 @ @ 1

AM-2-004

a9

8

AM-3-006

b

27

28

55

84

84

86

AM-3-007

c

56

88

AM-3-008

d

87

Pos: 33.8 /Zusammenbau-Anleitungen/AM Mähwerke/AM-CV Baureihe/AM-4-102 / AM-4-009 / AM-4-010 / AM-2-011 / AM-2-012 / AM-2-013 @ 73\mod_1307617244858_0.docx @ 653577 @ @ 1


83

AM-4-102

da

AM-4-009

e

11

AM-4-010

f

5870

10

67

AM-2-011

g52 10

7173

AM-2-012

h

3271

71

5182

81

80

AM-2-013

13

i



84

AM-4-015-2

II

p

jr

k

q

m n

l

l

oS


AM-3-016

j

36

53 �72

�6585

AM-3-017

k

31

57

77

7757

AM-2-018

6

7

I

5

AM-2-019

7666

61

m

Pos: 33.11 /Zusammenbau-Anleitungen/AM Mähwerke/AM-CV Baureihe/AM-2-020 / AM-2-021 / AM-2-022 / AM-2-023-1/ AM-4-024 / AM-4-104 @ 73\mod_1307618403781_0.docx @ 653969 @ @ 1


85

AM-2-020

n69

75

60

7

o

AM-2-021

29

78

63

6778

67

AM-2-022

3

64

79�68

p

26

AM-2-023-125

37

q

AM-4-104

s optional

40

40

AM-4-024

r

3337



86

AM-4-026

t uv

s

Pos: 33.13 /Zusammenbau-Anleitungen/AM Mähwerke/AM-CV Baureihe/AM-2-027 / AM-2-028-1 @ 73\mod_1307619656596_0.docx @ 654176 @ @ 1

AM-2-027

s

14

AM-2-028-1

60 mm

80 mm

151618

17

16 16

35

t

Pos: 33.14 /Zusammenbau-Anleitungen/AM Mähwerke/AM-CV Baureihe/AM-2-029 / AM-4-030-1 @ 73\mod_1307619793260_0.docx @ 654204 @ @ 1


87

AM-2-029

20

u

19

AM-4-030-1

v 37

24



88


AM-2-031

w

x zz

yyab


4

AM-2-032

w65

54 74

2

AM-2-033

x

AM-2-034

1

1

1

2

1

67

6277

y

AM-2-035

z



89

ab

6767

30

59

AM-2-036


Disposal of the machine

90

Pos: 35 /Überschriften/Überschriften 1/A-E/Entsorgung der Maschine @ 274\mod_1404207309028_78.docx @ 2060455 @ 1 @ 1

16 Disposal of the machine Pos: 36 /BA/Entsorgung der Maschine/Die Maschine entsorgen @ 274\mod_1404207434449_78.docx @ 2060544 @ 2 @ 1

16.1 Disposal of the machine

After the service life of the machine has expired, the individual components of the machine must be disposed of properly. The applicable country-specific, current waste disposal guidelines and the legal laws must be observed. Metal parts All metal parts must be brought to a metal recycling centre. The components must be freed from operating fluids and lubricants (gear oil, oil from hydraulic system, ...) before being scrapped. The operating fluids and lubricants must be brought separately to an environmentally friendly disposal point or recycling centre. Operating fluids and lubricants Operating fluids and lubricants (diesel fuel, coolant, gear oil, oil from hydraulic system, ...) must be brought to a disposal point for waste oil. Synthetic materials All synthetic materials must be brought to a recycling centre for synthetic materials. Rubber Rubber parts (hoses, tyres, …) must be brought to a rubber recycling centre. Electronic scrap Electronic parts must be brought to a disposal point for electronic scrap.

=== Ende der Liste für Textmarke Inhalt ===

91

17

A

Adjusting Skids ................................................... 78

Adjusting the Compensation Springs ................. 45

Adjusting the conditioner plate ........................... 49

Adjusting the cutting height ................................ 44

Adjusting the Swath Width .................................. 49

Adjusting the Tedder Speed ............................... 48

Affixing the Adhesive Safety and Information Labels ............................................................. 23

Appendix - Assembly Instructions ...................... 79

Attached devices ................................................ 14

Attaching the Three-Point Block ......................... 26

B

Before mowing .................................................... 39

Before the Start of the New Season ................... 74

Blade Changing on Cutting Discs ....................... 67

Blade Quick-Fit Device ................................. 66, 69

Blade Screw Connection .............................. 66, 68

C

Checking the Cutter Blades and Blade Holder ... 64

Clutching points .................................................. 25

Commissioning ................................................... 24

Connecting the hydraulic lines ............................ 31

Contact ................................................................. 7

Cutter Blades ...................................................... 65

D

Dangers in Case of Non-compliance with the Safety Instructions .......................................... 12

Default Setting of the Tractor's Lower Suspension Arms ................................................................ 47

Detaching the machine ....................................... 41

Deviating Torque ................................................ 57

Disposal of the machine ..................................... 90

Driving and Transport ......................................... 36

F

Fastening the Compensation Spring .................. 35

Filling Quantities and Lubrication Designations for Gearboxes ...................................................... 58

First installation ................................................... 24

Folding down the Safety Device ......................... 39

Friction Clutch ..................................................... 76

From transport into working position .................. 38

G

Guard Cloths ....................................................... 62

H

Headland Position .............................................. 40

Hydraulic system ................................................ 16

Hydraulics .......................................................... 31

I

Identification Plate ................................................ 8

Identifying Symbols in the Operating Instructions ....................................................................... 11

Inadmissible Modes of Operation ...................... 16

Information Required for Questions and Orders .. 8

Install the PTO shaft .......................................... 33

Intended Use ........................................................ 9

Intermediate PTO shaft ...................................... 34

Introduction .......................................................... 7

L

Lighting .............................................................. 37

Lubrication Chart ................................................ 72

M

Main gearbox ..................................................... 59

Maintenance ................................................ 16, 54

Maintenance – lubrication chart ......................... 71

Making Adjustments for Swathing ..................... 53

Metric Thread Screws with Control Thread ....... 55

Metric Thread Screws with Countersunk Head and Hexagonal Socket ................................... 56

Metric Thread Screws with Fine Thread ............ 56

Mounting onto the Tractor ............................ 25, 30

O

Oil Level Check and Oil Change Intervals (Gearboxes) ................................................... 58

Oil level check and oil change on the cutter bar 61

Operation ........................................................... 38

P

Parking support .................................................. 34

Personnel Qualification and Training ................. 12

Placing in Storage .............................................. 73

Pole protection ................................................... 63

Position of the Adhesive Safety Stickers on the Machine ......................................................... 20

Position of the General Information Labels on the Machine ......................................................... 22

PTO operation .................................................... 15

PTO shaft ............................................... 27, 33, 71

Purpose of Use .................................................... 7

92

R

Re-Ordering the Adhesive Safety and Information Labels ............................................................. 23

Replacing the Linings ......................................... 70

S

Safety .................................................................. 11

Safety Instructions and Accident Prevention Regulations ..................................................... 13

Safety-conscious work practices ........................ 12

Service life of the machine ................................... 9

Setting of the pole protection mechanism .......... 46

Setting of the tine conditioner ............................. 50

Settings ............................................................... 44

Spare Parts ......................................................... 54

Special equipment .............................................. 78

Special Tool ........................................................ 67

Speed gearbox ................................................... 60

Start-up ............................................................... 30

Switching from working position to transport position ........................................................... 36

T

Technical data .................................................... 10

Tedder ................................................................ 63

Test run .............................................................. 74

Test run .............................................................. 54

Tightening torques ............................................. 55

U

Unauthorised Conversion/Modification and Spare Parts Production ............................................ 16

Using the Machine for Work .............................. 40

W

Walterscheid Overload Coupling ....................... 76

Wide Swath Cover ............................................. 52

Working in the vicinity of power transmission lines ....................................................................... 17

MaschinenfabrikBernard Krone GmbHHeinrich-Krone-Straße 10, D-48480 SpellePostfach 11 63, D-48478 Spelle

Phone +49 (0) 59 77/935-0Fax +49 (0) 59 77/935-339Internet: http://www.krone.deeMail: [email protected]

Date post:	04-Jul-2020
Category:	Documents
Upload:	others
View:	0 times
Download:	0 times

AM 203 CV AM 243 CV / + B AM 283 CV / +B...Original operating instructions Disc Mower AM 203 CV AM...

Documents