AMERICAN MADE X SERIES LED SOLAR LIGHTING SYSTEM: X-35-LED-9750-285

SYSTEM OUTPUT 9750 LUMENS PER FIXTURE

SYSTEM VOLTAGE INPUT 12/24 VDC – OUTPUT 12/24 VDC

SYSTEM CERTIFICATION - ETL Listed compete system to – UL 1598 - Certified to CAN/CSA C22.2 No. 250.0 - Dark Sky Compliant

OPERATIONAL TEMPERATURES System is operational from -60° Celsius (with un-frozen batteries) to maximum temperature range of 60° Celsius with 90% humidity

SOLAR MODULES - High efficiency UL, CUL, and CE listed 285 watt panel Mono - 20 year warranty

BATTERY ENCLOSURE - Aluminum battery enclosure - Pre-wired and tested - Designed for a harsh or marine environment - Optional raised ridge rubber battery mat for thermal protection

ELECTRONICS - Pre-wired and mounted in battery enclosure box - Dual circuit breaker protected (no fuse replacement) - Maximum Power Point Tracking (MPPT) charge controller is

reverse polarity protected and cannot be damaged by wiring incorrectly

- Instant light test switch – no need to wait for sunset to confirm correct installation

LED LIGHT FIXTURE - Dark Sky Compliant - Glass cut off optics Phillips Illumiled LED Chips Color Temperature Options: � 4300k (standard option) � 5300k

TOP OF POLE SOLAR MOUNT Aluminum solar array mounting system to provide multiple degrees of adjustments for more precise alignment with the sun

GEL PACK BATTERY

- Zero maintenance gel pack battery - High capacity deep cycle - 3+ days back up power - Automatic low-voltage shutdown to protect battery - Battery operating temperature: -60° Celsius to 60° Celsius

SLI-AL 75W75W24V DC

AC 0.85A (max)

0.95>92%

SLI-AL 75WLED Parking Lot / Area Light, 150 - 250W HPS/MH Replacement

SLI-AL Series Style A Installation

SLI-AL Series Style B Installation

SLI-AL Series Style C Installation

SLI-AL Series Style D Installation

Hyundai Solar Module

www.hhi-green.com/solar/en

High Quality• IEC 61215 (Ed.2) and IEC 61730 by VDE• UL listed (UL 1703), Type 1 for Class A Fire Rating• Output power tolerance +3/-0 %• ISO 9001:2000, ISO 14001:2004 and ISO 50001:2011 Certified• OHSAS 18001:2007 Certified• Advanced Mechanical Test (8,000 Pa) Passed (IEC)

/ Mechanical Load Test (40 lbs/ft2) Passed (UL)• Ammonia Corrosion Resistance Test Passed• IEC 61701 (Salt Mist Corrosion Test) Passed

Limited Warranty• 1st year: 97 %• After 2nd year: 0.7 % annual degradation 80.2 % for 25 years ▶Please refer to the Hyundai Limited Warranty for more details.

※ Important Notice on Warranty The warranties apply only to the PV modules with Hyundai Heavy Industries Co., Ltd.'s logo (shown below) and product serial number on it.

Mechanical Characteristics

Dimensions 998 mm (39.29”)(W) × 1,640 mm (64.57”)(L) × 35 mm (1.38”)(H)Weight Approx. 18.7 kg (41.2 lbs)Solar cells 60 cells in series (6 ×10 matrix) with PERL technology (Hyundai cell, Made in Korea)

Output cables 4 mm2 (12AWG) cables with polarized weatherproof connectors, IEC certified (UL listed), Length 1.0 m (39.4”)

Junction box IP67, weatherproof, IEC certified (UL listed)Bypass diodes 3 bypass diodes to prevent power decrease by partial shade

Construction Front : Anti-reflective coating low-iron tempered glass, 3.2 mm (0.126”)Encapsulant : EVA Back Sheet : Weatherproof film

Frame Clear anodized aluminum alloy type 6063 (Black)

Hyundai Heavy Industries was founded in 1972 and is a Fortune 500 company. The company employs more than 48,000 people, and has a global leading 7 business divisions with sales of 51.3 Billion USD in 2013. As one of our core businesses of the company, Hyundai Heavy Industries is committed to develop and invest heavily in the field of renewable energy. Hyundai Solar is the largest and the longest standing PV cell and module manufacturer in South Korea. We have 600 MW of module production capacity and provide high-quality solar PV products to more than 3,000 customers worldwide. We strive to achieve one of the most efficient PV modules by establishing an R&D laboratory and investing more than 20 Million USD on innovative technologies.

PERLRG-Series Mono-crystalline Type

HiS-S280RG | HiS-S285RG | HiS-S290RG

Multi-crystalline TypeHiS-M265RG | HiS-M270RG | HiS-M275RG

※ Several models are under certification process.

[ Printed Date : December 2015 ]

Sales & Marketing Hyundai Bldg., 75, Yulgok-ro, Jongno-gu, Seoul 03058, Korea Tel : +82-2-746-4671, 7635, 8556 Fax : +82-2-746-7675

※All data at STC (Standard Test Conditions). Above data may be changed without prior notice.

HiS-M RG

265 270 275Nominal output (Pmpp) W 265 270 275

Voltage at Pmax (Vmpp) V 31.3 31.4 31.5

Current at Pmax (Impp) A 8.5 8.6 8.7

Open circuit voltage (Voc) V 37.9 38.0 38.2

Short circuit current (Isc) A 9.1 9.2 9.3

Output tolerance % +3/-0

No. of cells & connections pcs 60 in series

Cell type - 6” Multi-crystalline silicon with PERL technology (Hyundai cell, Made in Korea)

Module efficiency % 16.2 16.5 16.8

Temperature coefficient of Pmpp %/K -0.41 -0.41 -0.41

Temperature coefficient of Voc %/K -0.32 -0.32 -0.32

Temperature coefficient of Isc %/K 0.039 0.039 0.039

| Multi-crystalline Type |

※All data at STC (Standard Test Conditions). Above data may be changed without prior notice.

HiS-S RG

280 285 290Nominal output (Pmpp) W 280 285 290

Voltage at Pmax (Vmpp) V 31.7 31.8 32.0

Current at Pmax (Impp) A 8.8 8.9 9.1

Open circuit voltage (Voc) V 38.5 38.7 38.8

Short circuit current (Isc) A 9.4 9.5 9.7

Output tolerance % +3/-0

No. of cells & connections pcs 60 in series

Cell type - 6” Mono-crystalline silicon with PERL technology (Hyundai cell, Made in Korea)

Module efficiency % 17.1 17.4 17.7

Temperature coefficient of Pmpp %/K -0.42 -0.42 -0.42

Temperature coefficient of Voc %/K -0.30 -0.30 -0.30

Temperature coefficient of Isc %/K 0.047 0.047 0.047

| Mono-crystalline Type |

Nominal Operating Cell Temperature 46˚C ± 2

Operating Temperature -40 - 85˚C

Maximum System Voltage DC 1,000 V (IEC)DC 600 V (UL)

Maximum Reverse Current 15 A

7.5 (0.3”)

8 (0.32”)

4 (0

.16”

)

11 (0

.43”

)

8-Ø7 SLOT THRU

SECTION C-C

DETAIL B

DETAIL A

18 (0.71”)11 (0.43”)

1,64

0 (6

4.57

”)

A

B(+)(-)

1,000 mm (39.37”)4 mm2 CABLE &CONNECTOR

1,000 mm(39.37”)4 mm2 CABLE &CONNECTOR

GROUND MARK

4 X Ø4.2GROUND HOLE

C

C

4 X Ø7-L11HOLES

998 (39.29”)

548

(21.

57”)

954 (37.56”)

253 (9.96”)

360

(14.

17”)

800

(31.

49”)

60 (2.4”)

35 (1

.38”

)

30 (1.18”) 1.8 (0.07”)

1,000 W/m2

00 5 10 15 20 25 30 35 40 45

1

2

3

4

5

6

7

8

9

10

5˚C

25˚C

45˚C

65˚C

00 10 15 255 20 30 35 4540 50

1

2

3

4

5

6

7

8

9

10

Current [A]

Voltage [V]Current [A]

Voltage [V]

1,000 W/m2

800 W/m2

600 W/m2

400 W/m2

200 W/m2

| Module Diagram | | I-V Curves | (unit : mm, inch)

| Installation Safety Guide |

• Only qualified personnel should install or perform maintenance.• Be aware of dangerous high DC voltage.• Do not damage or scratch the rear surface of the module.• Do not handle or install modules when they are wet.

Electrical Characteristics

Improve PV Module and Battery Performancewith Maximum Power Point Tracking

Patented MPPT Technology IncreasesCharge Current up to 30% Or More!

FullyAdjustableSolar Lighting

Control

Patented Maximum Power Point Tracking technology allows SLI's 3724iX to increase charge current up to 30% or more compared to conventional charge controllers. Don’t waste your money by throwing PV power away! Get the power you paid for with a Solar Boost charge controller.

SLI's 3724ix’s advanced fully automatic 3-stage charge control system will properly charge flooded lead-acid, AGM and Gell batteries resulting in improved battery performance with less battery maintenance. The dual 15/20 amp rating will deliver up to 15 amps in 24 volt systems, or up to 20 amps in 12 volt systems. An automatic or manualequalize function is also provided to periodically condition flooded lead-acid batteries. To further enhance versatility, a user configurable auxiliary output and Blue Sky Energy’s advanced IPN™ network interface are also included.

The user configurable auxiliary output can serve as either a 15/20 amp load controller, or as a 2 amp auxiliary battery charger. The load control feature can be used to limit excessive battery discharge in unattended remote systems, whereas the auxiliary battery charge feature is ideal for charging a separate battery such as the engine start battery in a boat or RV. The auxiliary output can also provide fully adjustable dusk to dawn lighting control.

Solar Lighting Intl's advanced Integrated Power Net™, or IPN Network, allows up to 8 IPN capable charge controllers to communicate with each other and operate as a single machine rather than separate charge controllers. The IPN network also allows networked controllers to share an optional battery temperature sensor and remote display. The IPN network does not require a display or other special hardware to operate.

15 Amp 24 Volt & 20 Amp 12 Volt Rating Supports A Wide Range Of Applications

Optional IPN-ProRemote Display Provides Charge Control & Full-Featured Battery System Monitoring

3-Stage Charge Control with Filtered PWM Output Improves Battery Performance & Life While Minimizing Battery Maintenance

Clear Anodized Faceplate, Galvanized Mounting Box & Conformal Coated Electronics Resist Corrosion

Automatic or Manual Equalization To Periodically Condition Flooded Lead-Acid Batteries

IPN Network Interface Coordinates Multiple Controllers & Shares Optional Battery Temperature Sensor & Display

Auxiliary Output Provides 15/20 Amp Load ControlOr 2 Amp Auxiliary Battery Charge

Lighting Control Provides Separate Post-Dusk & Pre-Dawn timers

Full 12 Month Limited Warranty

SLI 3724iX

How Does SLI MPPT Charge ControllersIncrease Charge Current?SLI MPPT charge controllers increase charge current

by harvesting more PV power. A conventional chargecontroller simply connects the PV module to the batterywhen the battery is discharged which can artificially limithow much power a PV module can deliver.

Patented SLI Inc. MPPT technology operates thePV module at it’s optimum voltage where it can producethe greatest amount of power rather than at batteryvoltage. The higher power extracted from the module isthen provided to the battery as increased charge current.

The actual charge current increase you will see variesprimarily with module temperature and battery voltage.In comfortable temperatures, current increase typically

varies between 10 to 25%, with 30% or more easilyachieved with a discharged battery and cooler tempera-tures. What you can be sure of is that SLI MPPTcharge controllers will deliver the highest charge currentpossible for a given set of operating conditions.

Typical 75W PV Module Performance @ STC

Available From:

SPECIFICATIONS Solar Lighting International MPPT 3724Output Current Rating

Nominal Battery Voltage 12 / 24VDCPV Input Voltage

Power Consumption 0.20W typical standby plus 0.40W each for charge ON & Load ON Charge Algorithm

Acceptance Voltage 14.2VDC fixed (range 10.0 – 40.0VDC )

13.2VDC fixed (range 10.0 – 40.0VDC )

15.2VDC fixed (range 10.0 – 40.0VDC )

Float Voltage

Equalization Voltage15.5VDC fixed (range 10.0 – 40.0VDC )Voltage Setpoint Limit

Single output configurable as either: 20 amp 12V / 15 amp 24V load controller –or– 2A auxiliary battery charger 2 Amp typical, same charge voltage as primary battery

Auxiliary Output FunctionAux. Battery charge

Load Control / (Range 10.0 – 40.0VDC ,or battery amp-hours from full )

Temperature Compensation

Power Conversion Efficiency 97% Typical @ 28 Volt 12 Amp Output

Volt/Amp Accuracy/Range Ammeters 25.0A±0.50% FS

Communication

Environmental -40 to +50 C, 10 – 90% RH non-condensing

20 amp maximum (12V battery & 12V PV’s) 15 amp maximum (battery or PV’s > 12V nominal)

Dusk-to-Dawn Cntrl Variable Post-Dusk and Pre-Dawn timers , Range 0.5 - 20.0 Hours

As a part of our continuous improvement processspecifications are subject to change without prior notice.

Voltages double for 24V batteryWith IPN-ProRemote which may be used as a setup tool

only. Charge voltage setpoints may require modification with IPN-ProRemote based on battery manufacturer's recommendations.

Solar Lighting International's proprietary IPN Network interface

Current rating and current limit are 20A when charging a 12V battery from nominal 12V PV modules. If PV VOC ever exceeds 30V (>12V nominal PV modules) current rating and current limit become 15A.

Physical Configurationand Dimensions

57VDC maximum (Recommend maximum VOC

3-stage Bulk/Acceptance/Float plus automatic Equalize

Optional sensor adjusts charge voltage based on battery temperature–5.00 mV/°C/cell correction factor (Range 0.00 to –8.00 mV/°C/cell ) sensor range –60 to +80°C

Open frame construction with conformal coated electronics mounted to rear of 5.3” x 5.3” (13.5cm x 13.5cm)clear anodized aluminum face plate. Mounts into standard 411/16” (11.9cm) square electrical box which is included.

SpecificationCells Per Unit

Voltage Per Unit

Normal Operating Temperature Range

Capacity

Weight

Max. Discharge Current

Internal Resistance

Operating Temperature Range

6

12o

160Ah@10hr-rate to 1.80V per cell @25 C

Approx. 44.0 Kg ( ±1.5%)Tolerance

160 A (5 sec)

Approx. 4 mΩ

Discharge: -20 C~60 Co o

Charge: 0 C~50 Co o

Storage: -20 C~60 C

o o

o o25 C±5 C

Float charging Voltage

Recommended Maximum ChargingCurrent

Equalization and Cycle Service

Self Discharge

Terminal

Container Material

Terminal F5/F12

Dimensions

o13.6 to 13.8 VDC/unit Average at 25 C

43.5 A

o14.6 to 14.8 VDC/unit Average at 25 C

DC12-160 (12V160Ah)

oConstant Current Discharge Characteristics: A (25 C)

oConstant Power Discharge Characteristics: W (25 C)

F.V/Time 5MIN 10MIN 15MIN 30MIN 2HR 3HR 4HR 5HR 8HR 10HR 20HR1HR

F.V/Time 5MIN 10MIN 15MIN 30MIN 2HR 3HR 4HR 5HR 8HR 10HR 20HR1HR

SLI Valve Regulated Lead Acid (VRLA) batteries can be stored o

for more than 6 months at 25 C. Self-discharge ratio less than 3% o

per month at 25 C. Please charge batteries before using.

DC (Deep Cycle) series is specially designed for frequent cyclic discharge. By using strong grids and specially designed active material, the DC series battery offers 30% more cyclic life than the standby series. It is suitable for solar energy systems, marine and RV etc.

A.B.S. UL94-HB, UL94-V0 Optional.

All mentioned values are average values .( ±2%)Tolerance

9.60V 447.0 333.4 263.1 145.7 90.51 55.88 37.97 30.62 25.42 16.74 15.09 7.99

10.0V 434.1 317.3 257.7 143.8 89.30 54.75 37.27 30.18 25.19 16.68 14.94 7.84

10.2V 421.2 306.1 253.6 141.6 88.45 54.17 36.94 29.88 25.03 16.53 14.79 7.69

10.5V 378.2 282.4 241.5 137.7 87.37 53.46 36.61 29.44 24.82 16.38 14.65 7.54

10.8V 341.4 257.5 222.6 133.2 86.15 53.03 36.18 28.43 24.70 16.31 14.51 7.46

11.1V 291.5 230.2 199.6 128.1 84.11 50.89 35.48 28.02 24.52 16.18 14.34 7.16

9.60V 4623 3551 2894 1668 1049 654.8 447.1 366.5 304.5 200.5 180.9 96.22

10.0V 4532 3442 2847 1650 1039 646.8 440.4 361.3 301.8 199.7 179.5 94.55

10.2V 4481 3351 2815 1636 1033 642.2 438.5 358.0 299.9 198.2 177.9 92.80

10.5V 4079 3121 2685 1603 1026 634.1 434.9 353.1 297.5 196.5 176.2 91.05

10.8V 3715 2877 2482 1565 1013 629.4 430.0 341.2 296.2 195.7 174.4 90.17

11.1V 3263 2601 2234 1522 998.1 605.8 422.8 336.3 295.1 194.3 172.5 86.95

Unit: mm Dimension: 344(L) 173(W) (H)× ×285

Terminal F5

POS NEG

Terminal F12

2

37

5344

Solar Lighting International, Inc. www.solarlightingitl.com

SHENZHEN RITAR POWER CO.,LTD.SHENZHEN RITAR POWER CO.,LTD.SHENZHEN RITAR POWER CO.,LTD.SHENZHEN RITAR POWER CO.,LTD.SHENZHEN RITAR POWER CO.,LTD.

URL:www.ritarpower.comURL:www.ritarpower.comURL:www.ritarpower.comURL:www.ritarpower.comURL:www.ritarpower.com

Maintenance & Cautions

Address: Rm405,Tower C, Huahan Building,Langshan Rd16, Nanshan District, ShenZhen, 518057, ChinaAddress: Rm405,Tower C, Huahan Building,Langshan Rd16, Nanshan District, ShenZhen, 518057, ChinaAddress: Rm405,Tower C, Huahan Building,Langshan Rd16, Nanshan District, ShenZhen, 518057, ChinaAddress: Rm405,Tower C, Huahan Building,Langshan Rd16, Nanshan District, ShenZhen, 518057, ChinaAddress: Rm405,Tower C, Huahan Building,Langshan Rd16, Nanshan District, ShenZhen, 518057, China

-20℃ -10℃ 0℃ 5℃ 10℃ 20℃ 25℃ 30℃ 40℃ 45℃

6V&12V 50% 70% 83% 85% 90% 98% 100% 102% 104% 105%

2V 60% 75% 85% 88% 92% 99% 100% 103% 105% 106%

6V&12V 46% 66% 76% 83% 90% 98% 100% 103% 107% 109%

2V 55% 70% 80% 85% 92% 99% 100% 104% 108% 110%

AGMBattery

Capacity Factors With Different Temperature

Battery Type

GELBattery

0.2C＜ （A）＜1.0C

Final DischargeVoltage V/cell

Discharge Current (A)

（A）≤0.2C

1.60V

（A）≥1.0C

1.75V 1.70V

Discharge Current VS. Discharge Voltage

Bolt

Terminal

Torque

M5 M6 M8

F3 F4 F13 F18 T25 T26 F8 F11 F12-1 F15 F5 F9 F10 F12 F14 F16

6~7N-m 8~10N-m 10~12N-m

Charging Method:

Charge the batteries at least once every six months,o

if they are stored at 25 C.

-0.2Cx2h+0.1Cx7h+0.05Cx4h

Constant Voltage

Fast

Constant Current

-0.2Cx2h+14.4-14.7Vx24h,Max. Current 0.3C

-0.2Cx2h+0.3Cx3h

Cycle service

※ Avoid battery over discharge, especially battery sereis connection use.

※ Charged with recommend voltage, ensure battery can be full recharged.

In general, recharge capacity should be 1.1-1.15 times discharge capacity.

※ Effect of temperature on cycle charge voltage: -4mV/℃/Cell.

※ There are a number of factors that will affect the length of cyclic service.

The most significant are depth of discharge, ambient temperature,

discharge rate, and the manner in which the battery is recharged.

Generally specking, the most important factors is depth of discharge.

Storage characteristic

Supplementary charge required(Carry out supplementary charge before use if 100% capacity is requires)

Supplementary charge requiredbefore use.This supplementary charge will help to recover the capacity and should be made as early as possible.

Supplementary charge may oftenfail to recover the capacity.The battery should never be left standing till this state is reached

Supplementary charge and storage guidelines

30℃

Storage Time (months)

20

0

Ca

pa

city

(%)

40

60

100

80

40℃

10℃

0℃

2 4 6 8 10 12 14 16 18 20 22 24

20℃

Life characteristics of cyclic use Life characteristics of cyclic use Life characteristics of cyclic use

100%

D.O.D

80%

D.O.D

50%

D.O.D

30%

D.O.D15%

D.O.D

300 600 900 1200 1500 1800

120

100

80

60

40

20

0

Number of Cycle(Times)

Capaci

ty(%

)

Charge characteristic Curve for standby use Charge characteristic Curve for standby use Charge characteristic Curve for standby use Charge characteristic Curve for standby use Discharge characteristic Curve Discharge characteristic Curve Discharge characteristic Curve Discharge characteristic Curve

Discharge Time

0.6

min

1.2 3 6 12 30 51 2

Hr

10 20 24

1C

Term

ina

lV

oltage

(V)

3C

0.16C

0.62C

0.35C

0.093C0.05C

0.24

0.20

0.16

0.12

0.08

0.04

0

120

100

80

60

40

20

0

0 42 86 28

Charge Time（h）

1210 1614 2018 24

Ch

arg

eV

olta

ge（

V）

Charge Voltage

① Discharge

100%（0.05CA×20h）50%（0.05CA×10h）

② ChargeCharge Voltage2.275V/CCharge Current0.1CA

③ Temperature 25℃

Charge Current

Charge Volume

Ch

arg

eC

urr

en

t(C

A)

Ch

arg

eV

olu

me

(%)

13

12

11

10

9

15

14

13

12

11

10

9

12V160AhDC12-160

Solar Lighting International, Inc.Phone 803-233-3461www.solarlightingitl.com

Annex to Certificate Registration No. 10000410 QM08

Custom Manufacturing Services, Inc.

142 Brick Street Princeton, WV 24740 United States of America

This annex (edition: 2012-07-17) is only valid in connection with the above-mentioned certificate. 2 / 2

Extended Location Scope

10002998 Custom Manufacturing Services, Inc. 400 Rogers Street Princeton, WV 24740 United States of America

The off-site at 400 Rogers Street, Princeton, WV performs the following primary functions: metal fabrication and assembly.