Amplifiers and
ModulatorsPremium range of VHF/UHF and
combination mast head and house
distribution amplifiers and modulators
to suit all needs. Matchmaster’s range
of mast head amplifiers have either
694MHz or 652MHz built in low pass
LTE/4G filters to reduce interference
from 4G mobile transmissions.
Products may vary from photo shown | www.matchmaster.com.au 41
42 www.matchmaster.com.au | Products may vary from photo shown
Amplifiers and Modulators4 Way Amplifier Splitter
10MM-AS38Features and Benefits
» Built in adjustable gain regulators
» Diecast housing inside heavy duty casting
» Built in power supply
» Suitable for
apartments
2 Way Amplifier Splitter
10MM-AS39Features and Benefits
» Built in adjustable gain regulators
» Diecast housing inside
heavy duty casting
» Built in power supply
» Suitable for apartments
Distribution Amplifier 40dB U/V
with Power Supply 4G Filtered
10MM-DMA42Features and Benefits
» Frequency range 45-694MHz
» Switchable inputs for UHF & VHF or U/V
» Separate gain controls for
band 1 & FM,
band 3 & UHF
» Metal casing for
excellent heat
dissipation
10MM-AS39 Specifications
Frequency Range 47-862MHZ
Gain 20dB
Gain Adjustment 0 ÷ -12dB
Max Output Level IMD3=60dB
(DIN45004B)100dBµV
Input And Output
Return Loss>10dB
Noise Figure <6dB
Port To Port Output Isolation >16dB
Power Consumption 230V ~ 50 Hz 3W
Operating Temp. Range -20°C ÷ +50°C
10MM-AS38 Specifications
Frequency Range 47-862MHZ
Gain 20dB
Gain Adjustment 0 ÷ -16dB
Max Output Level IMD3=60dB
(DIN45004B)100dBµV
Input And Output
Return Loss>10dB
Noise Figure <5dB
Test Point Attenuation -20dB
Port To Port Output Isolation >16dB
Power Consumption 230V ~ 50 Hz 3W
Operating Temp. Range -20°C ÷ +50°C
10MM-DMA42 Specifications
No. of Inputs 2 ‘F’ Type
No. of Outputs 1 ‘F’ Type
Gain UHF
VHF
40dB
33dB
Input & Output
Return Loss>10dB
Noise Figure <8dB
Gain Adjust VHF 15dB
Maximum Output 60dBIMR
35IMR
115dBµV (2 Ch)
103dBµV
(Cenelec 42Ch)
Screening VHF
UHF
>75dB
>65dB
Input/Output Impedance 75�Power Source 14-18VDC
Power Consumption 200mA
Block D & E UHF Amplifier
With LTE Filter And
Power Supply
10MM-DE34PFeatures and Benefits
» Built in 4G LTE 694MHz
low pass filter
» Filtering at 750MHz is >50dB
at maximum gain for UHF of 34dB
» Gain adjustment switch that is selectable
between 15, 25 and 34dB
» The UHF input return loss is >11dB
with a noise figure of <2.9dB for UHF
» Can be used with UHF antenna’s only
» The pack contains a 14VDC power supply and
cable ties for mounting
Products may vary from photo shown | www.matchmaster.com.au 43
Amplifiers and ModulatorsTERRA Amplifier 30dB Gain
10MM-HA024R30Features and Benefits
» Frequency range 45-862MHz
» Compact and reliable, great for
adding extra points to an indoor area
» Variable slope and gain control built-in
» Locally powered using 240V mains power
» ‘F’ connectors on all ports
» External test port, passive return path built in
» Switchable internal amplifier section allowing it to
switch effortlessly between low and medium gain
performance. This allows the gain of the amplifier
to be reduced without degrading the quality of the
signal being amplified
Amplifier Satellite/Terrestrial
10MM-HSA100Features and Benefits
» Amplifies both satellite and terrestrial services
» Terrestrial stage can be switched
to passive if it is not needed
» DC power pass through, allows power
to be passed to an LNB or masthead amplifier
» Independent gain and slope adjustment available
for both satellite and terrestrial bands.
» Foxtel approved (F30672)
» Ventilated power-supply section allowing for
greater heat dissipation and a longer MTBF
when compared to other amplifiers
10MM-HA024R30 Specifications
Gain18-20/27-30dB (Fixed
Slope Pre Correction)
Gain Adjustment17dB
Slope Adjustment
Flatness ±0.75dB
Input & Output
Return Loss
>14dB at 40MHz; -1.5
dB/Oct, But Not Less
10dB
Output Level CTB,
CSO (EN50083-3)97dBµV
Test Point -30dB
Noise Figure 8.5dB
Operating Temp. Range -20°C ÷ +50°C
10MM-HSA100 Specifications
Frequency Range SAT IF 950-2400MHz
Frequency Range
TERR TV47-862MHz
Gain SAT IF23-31dB
(Pre Correction)
Gain TERR TV
21-24dB
(Pre
Correction)/-
4dB Switchable
Gain Adjustment SAT IF 10dB
Gain Adjustment
TERR TV*18dB
Slope Adjustment SAT IF14/8dB
Switchable
Slope Adjustment
TERR TV*18dB
Input & Output Return Loss SAT
IF� 10dB
Input & Output Return Loss
TERR TV� 10dB
Maximum Output Level
IMD3=60dB (DIN45004B) TERR
TV
115dBµV
Noise Figure SAT IF 8dB
Noise Figure TERR TV 8dB
Mains Power Consumption230V ~ 50Hz
7.5W
Temperature Range -20°C ÷ +50°C
*Terrestrial gain, slope, adjustment and return path
are not available at passive terrestrial TV mode
44 www.matchmaster.com.au | Products may vary from photo shown
Amplifiers and ModulatorsAmplifier UHF 15dB 4G Filter
10MM-J15C-4GFeatures and Benefits
» U/V stabilised housing and cable tie
» Non-corrosive circuit board
» ‘F’ connectors
» Also available with power
supply (10MM-J15C-4GP)
10MM-J15C-4G/4GP Specifications
Frequency Range 520-694MHz
Gain Maximum 18dB
Noise Figure 2dB
Maximum Input Level 84dBµVMaximum Output Level 95dBµVConsumption 20mA/14VDC
Amplifier Masthead
UHF/VHF 24dB 4G Filter
10MM-J24BF-4GFeatures and Benefits
» Can be set to VHF only or combination
» Non-corrosive circuit board
» U/V stabilised housing
» Also available with power
supply (10MM-J24BF-4GP)
10MM-J24BF-4G/4GP Specifications
Band VHF UHF
Gain Maximum 24dB
Gain Control 14dB
Input Voltage 14VDC
Noise Figure 3.5dB
Input Maximum 35dBµV
Output Maximum 105dBµV
Frequency Range 174-230MHz 520-694MHz
Amplifier UHF/VHF
34dB 4G Filter
10MM-J34BF-4GFeatures and Benefits
» ‘F’ connectors
» Non-corrosive circuit board
» Also available with power
supply (10MM-J34BF-4GP)
10MM-J34BF-4G/4GP Specifications
Band VHF UHF
Gain Maximum 28dB 34dB
Gain Control -15dB
Input Voltage 14VDC
Noise Figure 3.5dB 2.5dB
Input Maximum 35dBµV
Output Maximum 105dBµV
Frequency Range 174-230MHz 520-694MHz
Amplifier 20dB Gain
Plug In 4G LTE Filter
10MM-MA20FLFeatures and Benefits
» 4G Lowpass filter output 694MHz
» Frequency 40-694MHz
» Ideal for improving
reception on a single TV.
» Warning indoor use only.
Do not allow exposure to moisture
or harmful elements.
Amplifier UHF 4G Filter
Super Low Noise
10MM-J25SLN-4GFeatures and Benefits
» Non-corrosive circuit board
» U/V stabilised housing
» Also available with power
supply (10MM-J25SLN-4GP)
10MM-J25SLN-4G/4GP Specifications
Frequency Range 520-694MHz
Gain 10-25dB
Noise Figure 1.5dB
Maximum Input Level 85dBµVMaximum Output Level 105dBµVConsumption 55mA/14VDC
Amplifier 34dB UHF/VHF
4G Filter
10MM-J34C-4GFeatures and Benefits
» ‘F’ connectors
» Non-corrosive circuit board
» Available with power
supply (10MM-J34C-4GP)
10MM-J34C-4G/4GP Specifications
Band VHF UHF
Frequency Range 174-230MHz 520-694MHz
Gain Maximum Passive-2 dB 36dB
Noise Figure 2.5dB
Maximum Input 84dBµV
Maximum Output 102dBµV
Consumption 60mA/14VDC
Products may vary from photo shown | www.matchmaster.com.au 45
Amplifiers and ModulatorsAmplifier 2 Way
4G LTE Filter
10MM-MA22FLFeatures and Benefits
» Ideal for TV and FM signals
to be split to 2 TV's
» 2 Way UHF/VHF amplifier
with integrated power
1 input 2 outputs
» Frequency range
40-694MHz
» 4G LTE low pass filter
694MHz
» 3 x A3 female IEC adaptors
» 15dB ± 3dB Gain
Amplifier 4 Way
4G LTE Filter
10MM-MA24RLFeatures and Benefits
» Power supply can be used
simultaneously for a masthead amplifier
» Warning: Indoor use only.
10MM-MA24RL Specifications
Frequency Range 45-694MHz
Number of Inputs 1
Typical Gain 8dB
Maximum Output 92dBµV at 60dB IMR
Low Noise �7.2dB
Power Supply 12V/500mA
Power Pass 230VAC/50Hz
Amplifier Masthead
4G UHF/VHF 30dB
With Power Supply
10MM-MA30PDFFeatures and Benefits
» Posistor protected right
angle regulated
power supply
» Heavy duty
clamping system
» New slide switchable
input selection
» Adjustable interstage gain on UHF & VHF
» 4G 652MHz low pass filter built in
Amplifier 4G VHF/UHF
10MM-MD15PFeatures and Benefits
» Includes 14VDC power
supply and cable
ties for mounting
» Passive VHF passing or
combining with 1.5dB
max insertion loss
» Use with a combination antenna
» LTE Filter: OFF: VHF + Ch21-69 (47MHz - 820MHz)
ON: VHF + Ch21-46 (47MHz - 652MHz)
» Filter attenuation @ 720MHz: 19dB,
@ 750MHz: 30dB
Block A, B & C UHF/VHF Amplifier
with LTE Filter and Power Supply
10MM-MB34PFeatures and Benefits
» Built in 4G LTE 610MHz low pass filter
» Filtering at 700MHz is >50dB at maximum gain for UHF of 34dB
» Gain adjustment switch that is selectable between
15, 25 and 34dB
» The VHF input return loss is >13dB and the UHF
return loss is >11dB with a noise figure of <2.9dB for UHF
» Can be used with VHF or UHF antenna’s or a combination
of both and includes a VHF on off switch
» The pack contains a 14VDC power supply
and cable ties for mounting
46 www.matchmaster.com.au | Products may vary from photo shown
Amplifiers and Modulators
4 Output Drop Amplifier
10MM-MDR6-4PFeatures and Benefits
» Forward path 85-1000MHz
» Return path 4-65MHz
» 12VDC 50Hz 150mA
» R.F Shielded
Modulator TERRA DSB
Stereo 85dBµV
10MM-MT57Features and Benefits
» Built-in test pattern generator (TPG)
for video and audio
» Frequency agile double sideband
multi standard TV modulators
» Adjustable audio input level and RF output level
» Connectors: video/audio - RCA sockets -
RF - ‘F’ female
» Foxtel Approval Number: F30811
10MM-MT57 Specifications
RF Output Level (Typical) 85dBµV
Level Adjustment 0 ÷ -20dB
Frequency Range*SC170-300MHz,
470-862MHz
Combining Through Loss
TERR/SAT1.5dB/2.5dB
Frequency Range of RF
Combining5-2150MHz
Signal/Noise Ratio �55dB
Power Consumption 230V - 50Hz 2.5W
Operating Temperature -10°C - +50°C
Dual Power Inserter
10MM-PDL1418Features and Benefits
» ‘F’ Type 500MA
» 14VDC OUT for vertical
» 18VDC OUT for horizontal
» ‘F’ type power inserter to power
satellite LNBs for horizontal
and vertical polarities
10MM-MDR6-4P Specifications
Number of Input 1
Gain 7±2dB
Insertion Loss -7±2dB
Noise Figure �4dB
Return Loss (IN & OUT) �10dB
Isolation (OUT & OUT) �20dB
MAX Output Level at -60dB IMD �106dBµV
DC Powering (INPUT-OUTPUT) Yes
UHF/VHF Pre-Amplifier
with LTE Filter
10MM-MD34Features and Benefits
» Built in 4G LTE 694MHz
low pass filter
» Filtering at 750MHz is >50dB at
maximum gain for UHF of 34dB
» Can be used with a combination
antenna or separate VHF and UHF
antennas by setting the built in switch
» Power through switch to drive extra amplifiers
for both VHF and UHF
» The pack contains cable ties for mounting
Masthead Amplifier UHF
24dB - 4G Filter And
Power Supply
10MM-MD24UPFeatures and Benefits
» 694MHz built in 4G
low pass filter
» Switchable 694MHz
low pass filter
» Gain with LTE filter 694MHz 24dB
» VHF switch diplexing max attenuation
2.84dB at 230MHz
» Heavy duty clamping system
10MM-MD24UP Specifications
GainUHF
BIII
25dB
-2±1.5dB
Return Loss �-10dB
Noise 5.5dB
Impedance 75�Operating Voltage 24VDC
Operating Current 65±10mA
Output Level for dB Gain
Amplifier (Definition per
ENBS50083-9 Standard)
�98dBµV
DC Powered 14VDC
Housing Nickle Plated
Connector75�, Female ‘F’
Type
Working Temperature -20°C - +60°C
Products may vary from photo shown | www.matchmaster.com.au 47
Amplifiers and ModulatorsPower Supply 18VDC
‘F’ Type 500MA
10MM-PSM18FFeatures and Benefits
» Zinc die cast housing, nickel plated
» Frequency range 5-2400MHz
» Insertion loss < 1dB
» Input: 100 - 240V ~ 50/60Hz
» Output: 18VDC 500MA
Power Supply 14V DC
0.3A PAL Type
10MM-PSD14PFeatures and Benefits
» Environmentally smart
» MEPS and RoHS compliant
» PAL Design Output:
14VDC 300MA
Power Inserter 24VDC
10-2050MHz
10MM-PI24Features and Benefits
» Frequency range 10-2050MHz
» Insertion loss 2dB
» Max 1.5 Amp
» Allows for mounting of the
drop amp away from the
power outlet
» Directs power to the drop amp while allowing
RF to pass to the TV
Power Supply 14V DC ‘F’ Type
10MM-PSD14Features and Benefits
» Reduces protrusion
» Environmentally smart
» MEPS and RoHS compliant
» Male ‘F’ type connection
» Output: 14VDC 300MA
Amplifier Satellite 18dB
Inline 950-2400MHz
10MM-SA18Features and Benefits
» Maximum output of
105dBµV at 35dB IMR.
» Frequency range 950-2400MHz
» Passes both DC and 22KHz
» The satellite amplifier is a fully screened remote
powered device which will work
in a voltage range of 12-18V DC
10MM-SA18 Specifications
No. of Inputs 1 ‘F’ Type
No. of Outputs 1 ‘F’ Type
Gain 20dB
Return LossInput
Output
8dB
8dB
Noise Figure 5dB
Maximum Output 105dBµV
ScreeningVHF
UHF
>75dB
>65dB
Input/Output Impedance 75�Power Source +11 ~ +20VDC
Power Consumption 40 ~ 60mA @ 18VDC
Working Temperature -20°C ~ +55°C
Universal Masthead Amplifier
With Power Supply 4G
10MM-UA30PDFFeatures and Benefits
» Passive VHF passing or combining
with 1.5dB max insertion loss
» Filter Att @ 720MHz: 19dB, @ 750MHz: 30dB
» Use with a combination antenna or separate VHF
and UHF antennas by setting the in-built switch
» 4G - 694MHz Low Pass LTE Filter
10MM-UA30PDF Specifications
Input Voltage 14VDC
VHF Input Return Loss<13dB
UHF Input Return Loss
Power Supply Included Yes
Max GainUHF Band 3 FM Band 1
30 30 30 Passive
48 www.matchmaster.com.au | Products may vary from photo shown
Amplifiers and ModulatorsAmplifier 39dB Forward Gain
5-30MHz Passive Return
14MM-BA213UFeatures and Benefits
» High output amplifier capable of high channel loads
» Ga-As push pull amplification for low distortion
» Variable gain control to set output of the amplifier
and slope adjustment for cable compensation
» Includes Passive Return Path module
» Diecast housing for high RF screening
» 230~260VAC mains powered
14MM-BA213U Specifications
Forward Path* 47-862MHz
Return Path* 5-30MHz
Forward Path Gain** 39dB
Return Path Gain -2.5dB
Flatness*** ±0.5dB
Gain Adjustment 20dB
Slope Adjustment
Typical18dB
Inverse Cable Equaliser 0-9dB in 1dB Step
Output Level CTB, CSO
(EN50083-3)****-20dB
Input and Output Return
Loss*****>14dB
Noise Figure <7dB
Test Points Attenuation -20dB
Mains Powering 230V ~ 50Hz 11W
Operating Temperature
Range-20°C - +50°C
* Depends on plug-in modules: return path passive
pd 02-xx or active pr 02-xx (return path modules
should be ordered separately)
** With link 0dB instead of interstage attenuators
are supplied in scope of the amplifier delivery
*** For amplifier with return path - ±0.7dB
**** Measured with 6dB interstage equaliser
***** When f�40MHz, return loss �14dB (40MHz) -
1.5dB/octave, but not less 10dB
Passive Return Path Module
For 14MM-BA213U
14MM-PD02-65Features and Benefits
» Used in MATV system where signal
is returned back to BA213 amplifier
» Easy plug in
14MM-PD02-65 Specifications
Frequency RangeReturn Path 5-65MHz
Forward Path 87-862MHz
AttenuationReturn Path 1.5dB
Forward Path 1dB
Active Return Path Module
For 14MM-BA213U
14MM-PR02-30Features and Benefits
» Used for TERRA BA series broadband amplifiers
» Shapes the characteristics of the amplifier
in return path
14MM-PR02-30 Specifications
Frequency RangeReturn Path 5-30MHz
Forward Path 47-862MHz
GainReturn Path 21dB
Forward Path -1dB
Output Level IMD3=60dB 113dBµV
Gain/Slope Adjustment 20dB
Noise Figure 4dB
Products may vary from photo shown | www.matchmaster.com.au 49
Amplifiers and Modulators
Specifications
Product Code 14MM-DM04 14MM-DM05Video Encoding MPEG-2 MP@ML(4:2:0) H.264 MP@L 3.0 3.0/3.1/4.0
Video Interface CVBS*1 HDMI*1
Video Resolution720x576_50i (PAL);
720x480_60i
Input: [email protected]/60FPS Output: 480p@30FPS
Input: 576i@50FPS Output: 576p@25FPS
Input: 720p@50/59.94/60FPS
Output: 720p@50/59.94/60FPS
Input: 1080i@50FPS Output: 1080p@25FPS
Input: [email protected]/60FPS Output: 1080p@30FPS
Input: [email protected]/60FPS Output: 1080p@30FPS
Video Aspect Rate - 16:9, 5:4
Video Bit Rate 1.000-19.500 Mbps 1.000-18.000 Mbps
Audio Encoding MPEG1 Layer II MPEG-1 Layer 2, MPEG-2 AAC
Audio Interface 1*Stereo/Mono -
Audio Resolution 48KHz
Audio Bit Rate64, 96, 128, 192, 256,
320, 384kbps64, 96, 128, 192, 256, 320 kbps
Modulator Section Standard DVB-T COFDM
Bandwidth 6M, 7M, 8M
Constellation QPSK, 16QAM, 64QAM
Code Rate 1/2, 2/3, 3/4, 5/6, 7/8
Guard Interval 1/32, 1/16, 1/8, 1/4
Transmission Mode 2K 2K, 8K
MER �42dB �31dB
RF Frequency 30-960MHz, 1KHz step 142.5-858 MHz, 1KHz step
RF Output Level-16 - -36dBm (73-
93dBµV), 0.1dB step-14 - +6dBm (93-113dBµV), 0.1dB step
System Management Local Control; LCD + Control Buttons
Language English
LCN Insertion Yes
Upgrade JTAG or USB USB
Power Supply DC 12V
Operating Temperature 0˚-45˚C
CVBS To COFDM Modulator
14MM-DM04Features and Benefits
» 1 x RCA input
» Standard Definition digital modulation
» Allows audio/video signal input to TV distributions
» Can be used with home entertainment systems,
surveillance control, hotel digital signage, shops etc
HDMI To COFDM Modulator
14MM-DM05Features and Benefits
» 1 x HDMI input, MPEG4 output only
» High Definition digital modulation
» Allows audio/video signal input to TV distributions
» Can be used with home entertainment systems,
surveillance control, hotel digital signage, shops etc
50 www.matchmaster.com.au | Products may vary from photo shown
Amplifiers and ModulatorsAmplifier With 30MHz
Return Path
14MM-HA205R30
Amplifier With 65MHz
Return Path
14MM-HA205R65
Amplifier With 30MHz Return
Path, Remote Powered
14MM-HD205R30Features and Benefits
» Slope adjustment for cable compensation
» Ga-As push pull amplification for low distortion
Specifications
Product Code 14MM-HA205R30 14MM-HD205R30 14MM-HA205R65Forward PathFrequency Range 47-862MHz 87-862MHz
Gain Switchable* 27/36dB
Gain Adjustment 18dB
Slope Adjustment 18dB
Interstage Equaliser -6/-3/0dB
Flatness* ±0.75dB
Input & Output Return Loss >14dB at 40MHz; -1.5dB/oct, but Not Less 10dB
Output Level CTB, CSO (EN50083-3)** 109dBµV
Noise Figure 8dB
Test Points Attenuation -20dB
Return PathFrequency Range 5-30MHz 5-65MHz
Gain Switchable 27/-4dB
Gain Adjustment 18dB
Input Attenuator -10/0dB
Output Equaliser -6/-3/0dB
Flatness ±0.75dB
Return Loss >14dB
Noise Figure 7dB (Active, 0dB Input Attenuator)
Maximum Output Level IMD3=60dB
(DIN45004B)115dBµV
GeneralPower Supply 230V 50Hz 7.5W 24-65V 50Hz 6.5W 230V 50Hz 7.5W
Operating Temperature -20°C - +50°C
* For amplifier with return path measured 10MHz after the starting frequency of forward path
** With 6dB interstage equaliser
Products may vary from photo shown | www.matchmaster.com.au 51
Amplifiers and ModulatorsTerrestrial Amplifier Broadband/
Split Band Amplifier
14MM-JA01Features and Benefits
» Interstage attenuators and dynamic range of 30 dB
» High gain (up to 40 dB), high output (122 dBµV)
» Slope adjustment on VHF/UHF and UHF inputs
» 4 inputs and 5/12 VDC switchable
UHF remote power
» Broadband / Split Band Amplifier
» VHF/UHF input with return path
14MM-JA01 Specifications
Frequency
Range
FM
B3, DAB
UHF
VHF-UHF
88-108MHz
174-240MHz
470-790MHz
5-1000MHz (RP: 5-65)
Gain
FM
B3, DAB
UHF
VHF-UHF
0-32dB
0-32dB
5-40dB
5-40dB
Return Pass Loss 2dB
Slope
AdjustmentVHF-UHF -18dB to -8dB
Maximum Input Power 110dBµV
Maximum Output Power >122dBµV
Noise Figure
FM
B3, DAB
UHF
VHF-UHF
8dB
7dB
5dB
6.5dB
Return Loss >10dB
UHF Remote
Power
B3, DAB
UHF
5 VDC (200mA)/12
VDC (100mA)
5 VDC (200mA)/12
VDC (100mA)
Supply Voltage 200-264VAC
Power Consumption 5.5W
Amplifier 40dB Satellite
34dB Terrestrial
14MM-STA40AFeatures and Benefits
» Metal casing for excellent heat dissipation
» Ideal for headend applications
» Foxtel approved (F30092)
» Wall mountable
» Separate gain and slope controls
14MM-STA40A Specifications
Terrestrial SatelliteMaximum Gain 34dB 40dB
Gain Adjust 15dB
Equalisation Adjust 17dB 7-10dB
Output Level
(42Ch/20T)103dBµV 110dBµV
Noise Figure <7dB <8dB
Number of Inputs 1
Frequency Range5-30MHz, 45-862MHz,
950-2150MHz
Return Path 5-30MHz (Passive)
Mains Voltage 240V
Connection ‘F’ Type
Return Loss >12dB
52 www.matchmaster.com.au | Products may vary from photo shown
Amplifiers and ModulatorsDistribution Amplifier
45dB UHF/VHF Terrestrial
With Internal Power Supply
14MM-TA242Features and Benefits
» Foxtel Approved (F30092)
» Metal casing for excellent heat dissipation
» Separate gain
controls
14MM-TA242 Specifications
Number of Inputs 2
Frequency Range47-144MHz, 175-230MHz,
470-862MHz
Number of Outputs 1
Amplification BI + FM, B I I I, UHF
Gain 35/35/45dB
Gain Adjust 20dB
Output Level (42Ch) 108dBµV
Noise Figure <8dB
Mains Voltage 240V
Test Points Out -30dB
Split-Band Multi-Input MATV
Amplifier
14MM-TA540AFeatures and Benefits
» 5 input terrestrial amplifier
» TV gain adjustment range 0-20dB
» Impedance 75Ohm
14MM-TA540A Specifications
Number of Inputs 5
Frequency Range47-108MHz, 175-230MHz,
3 x 470-862MHz
Number of Outputs 1
Amplification Terrestrial
Gain 40/40/45dB
Gain Adjust 20dB
Output Level (42Ch) 105dBµV
Noise Figure <8dB
Mains Voltage 240V
Test Points Out -30dB
Distribution Amplifier 40dB
14MM-TWA40Features and Benefits
» 1 input F type
» TV gain adjustment range 0-20dB
14MM-TWA40 Specifications
BandVHF
U+V/UHF
Switchable
B111 B1+FM U+V UHF
Frequency174-
230MHz
45-
144MHz
45-
862MHz
470-
862MHz
Band Gain 35dB 45dB
DSR
(Output
Level)
110dBµV 108dBµV
Flatness
Response±1.5dB
Noise
Figure<7dB <8dB
Output
VoltageDC 14V/70mA
Products may vary from photo shown | www.matchmaster.com.au 53
Amplifiers and ModulatorsDual Split Band Amplifier
SAT IF/FTA
14MM-VS95Features and Benefits
» Inputs: 2x TERR + SAT with output range
47~862MHz and 950 to 2150MHz
» Dual Band amplifier for both
Satellite and Terrestrial
» Mains power operated
» Industry standard F connectors
» Test ports integrated for measurement
» Full diecast chassis water resistant
14MM-VS95 Specifications
Frequency 47-862MHz 950-2150MHz
Amplification 23-29dB 25-32dB
Equaliser 0/5dB 0/6dB
Attenuator 0-20dB
Isolation SAT/SAT - >45dB
Noise �6
Max. Ouput Level
(DIN45004A1)106dBµV 117dBµV
Max. Output Level
(DIN45004B)118dBµV 120dBµV
Main Voltage 230VAC
Power
Consumption9W
Housing Zinc die-cast
Operating
Temperature
Range
-10˚- +50˚C
Screening Factor Class A
Max. Humidity 95%
Value Line Distribution Amplifier
Remote Feed
14MM-VX25Features and Benefits
» Distribution amplifier programmable
via hand controller
» Output range 47~862MHz
» Return path configurable from
cutoff at 30 or 65MHz
» Remote powered 27 to 65VAC
» Full diecast chassis water resistant
14MM-VX25 Specifications
Frequency Range 47/85-862MHz
Gain 36dB
Output Level CENELEC, Flat 109dBµV
- CSO/CTB �64/�60dB
Output Level CENELEC 7dB
Slope112dBµV
- CSO/CTB �63/�60dB
Attenuator 0-15dB, 0,5-dB-steps
Equaliser 0-15dB, 0,5-dB-steps
Interstage Attenuator 0/5dB
- Equaliser 0/7dB
Noise Figure <7dB
Test Socket -20dB
Operating Voltage 27-65 VAC
Power Consumption <13W
Connectors Input Output PG11
Remote Power CurrentInput < 6 A;
Output < 3 A
Ambient Temperature -20°C - +55°C
EMC CE, Class A
54 www.matchmaster.com.au | Products may vary from photo shown
Amplifiers and ModulatorsDistribution Amplifier 40dB
14MM-VX26H-3041Features and Benefits
» Output range 47-1006MHz
» 40dB Gain
» Return Path 5-30MHz 24dB
» Integrated return channel and diplexers
» Foxtel approved (F30783)
14MM-VX26H-3041 Specifications
DownstreamFrequency Range 85-862MHz
Gain Single Output 40dB
Output
Level
CENELEC
42ch, flat111dBµV
6dB Slope 114dBµV
CSO �60dB
CTB �60dB
Noise Figure �6dB
Attenuator1dB Steps 0-15dB
(Jumper) 0/10dB
Equaliser 1.5dB Steps 0-22.5dB
Interstage Slope (Jumper) 0/6dB
Interstage Attenuation
(Jumper)0/5dB
Test Socket -20dB
Return PathFrequency Range 5-65MHz
Gain (active/passive) 32dB/-3dB
Noise Figure �6dB
Output
Level
2nd Order typ. 109dBµV
3rd Order typ. 115dBµV
Max. Load 1 TS
140120dBµV
Attenuator 1dB Steps 0-15dB
Output Attenuator
(Jumper)0/5dB
Equaliser (Jumper) 0/3/6/9dB
GeneralOperating Voltage 180-265VAC
Power Consumption <21W
Connectors F-Type
Remote Power CurrentInput <6A;
Output <3A
Operating Temperature -20˚ - +55˚C
In House Distribution Amplifier
14MM-VX87Features and Benefits
» Frequency Range US/DS 5-30/47-862 MHz
» With passive return path
» Adjustable level and equalizer
» F connectors
» Wall mounting
» Metal housing
14MM-VX87 Specifications
Gain DS 28-31dB
Attenuator 0-18dB
Equaliser 3-18dB
Output Level DS
CENELEC, Flat96dBµV
Output Level DS
CENELEC, 6dB Slope98.5dBµV
Output Level DS
EN50083-5/3.Ord114dBµV
Noise Figure <8dB
Return Path -2dB
RF Inputs and Outputs ‘F’ Type
Operating Voltage 230VAC 50/60Hz
Power Consumption 3.5W
Operating Temperature -20°C - +55°C
EMC CE, Class A
5/8” To PG11 Adaptor
14MM-ZG01Features and Benefits
» Used for 14MM-VX series amplifiers
» Adaptor for distribution cable
» Chassis coupler
PG11 To F Type Adaptor
14MM-ZG28Features and Benefits
» Used for 14MM-VX24 to VX52 amplifiers
» Adaptor for distribution cable
» PG11 to F female